As we've enabled multiplatform kernels on ARM, and greatly done away with
the contents under arch/arm/mach-*, there's still need for SoC-related
drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
with power management blocks on these SoCs for use by clock, regulator and
bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be confused with
PSCI (Power State Coordination Interface). SCPI is used to communicate with
the assistant embedded cores doing power management, and we have yet to see
how many of them will implement this for their hardware vs abstracting in
other ways (or not at all like in the past).
- To make confusion between SCPI and PSCI more likely, this release also
includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWQC+cAAoJEIwa5zzehBx3jEUP/0GpxfDVanEUkudVLLe7J0RH
CNlRan107Cw6hXRUJo7elEsuCALjccXjc1CAH4+RnNpOAeBKW97n+WU7trTv+wUZ
sQX4SkBPKFBlgwGF2qhsi5q74gms/BrgtCa4kNb9joOYso039tlfIOPzK80DMkOm
TkyIJdUCgFJMjCQLhX6kGT0PDcrbIjb6aA2cF3FAVeaJA7uz8lNe/eHJr3oHxIEY
CvC651yJ2mIHQUU4BJx/AJo+wXg3dRUXNCAtBjwLRPEAzduYZXYm1ZTVIby/1q9r
dR2KDFEuibODXmXrDBzKNJwCu/TLJEwo/1oPaEIVfY91XLKfiWUhgVqa1o1I+d9U
XoGPibCW461qFahjQW87MfInALpCOA7/RbTNjFp+MVyipCYvkaYq7KFiYEldgFDx
z4Qx/J4hYc2TlDWrpNiUCZMfmhwi7y+Ib+tnenYTO1eyMuw0e9mfnVdjk5iU3Pvk
Ye4qPqpYclJruyHbYi164878+1lLaW2NCUgC3rkBO/GWPAzp7d9iLWoZ3PuyD5i5
PEjs668UcRdZYbI4rdrhGHL8Eq9Gnuc4Rthu7HxPOK+DG0XgP8r97PhM8aYGYVDO
+yikBtjWRsA9fPj3rMKA3UsQ61DAeR9LmZ0XPGjWFMCjCG0JlUoIMaA+Uu0i8fr8
95qxBVxbO7rhL39r1rhV
=dm+I
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9u+p
-----END PGP SIGNATURE-----
Merge tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
Merge "ARM System Control and Power Interface(SCPI) support" from Sudeep Holla
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
* tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
hwmon: Support thermal zones registration for SCP temperature sensors
hwmon: Support sensors exported via ARM SCP interface
firmware: arm_scpi: Extend to support sensors
Documentation: add DT bindings for ARM SCPI sensors
cpufreq: arm_big_little: add SCPI interface driver
clk: scpi: add support for cpufreq virtual device
clk: add support for clocks provided by SCP(System Control Processor)
firmware: add support for ARM System Control and Power Interface(SCPI) protocol
Documentation: add DT binding for ARM System Control and Power Interface(SCPI) protocol
The TMP75C has a different control register layout and only supports
12-bit temperature samples (0.0625 deg C).
The continuous sample rate is ~12 Hz.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Create a driver to add support for SoC sensors exported by the System
Control Processor (SCP) via the System Control and Power Interface
(SCPI). The supported sensor types is one of voltage, temperature,
current, and power.
The sensor labels and values provided by the SCP are exported via the
hwmon sysfs interface.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Sudeep Holla <sudeep.holla@arm.com>
NCT6793D is register compatible with NCT6792D.
Also move nct6775_sio_names[] closer to enum kinds to simplify
adding new chips.
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch updates description of fam15h_power driver, its scope is
extended to family 16h processsors.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC3886 is a is a dual PolyPhase DC/DC synchronous step-down switching
regulator controller. It is mostly command compatible to LTC3883,
but supports two phases instead of one.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2980 and LTM2987 are command compatible to LTC2977. They consist of
two LTC2977 on a single die, and are instantiated as two separate chips,
each supporting eight channels.
Suggested-by: Michael Jones <mike@proclivis.com>
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2975 is mostly compatible to LTC2974, but supports input current
and power measurement.
Tested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC3882 is mostly compatible with LTC3880. Major differences are that it
does not measure the input current, and it no longer supports LTC's legacy
mechanism to identify the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add device IDs and references for Texas Instruments TPS544B20, TPS544B25,
TPS544C20, and TPS544C25 to the generic PMBus driver.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX20751 is a multiphase power controller with internal buck converter.
It uses VR12.0 to report the output voltage. This requires an explicit
driver, since the VR version can not be auto-detected.
The chip supports a manufacturer specific command to fine-tune the output
voltage. This command is not currently supported.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the IT8732F. This chip is pretty similar to IT8721F,
with the main difference being that the ADC LSB is 10.9 mV instead of
12 mV.
Signed-off-by: Justin Maggard <jmaggard@netgear.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADM1293 and ADM1294 are mostly compatible with other chips of the same
series, but have more configuration options. There are also some
differences in register details.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pwm attributes have well defined names, which should be used.
Cc: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
Cc: stable@vger.kernel.org #v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add an item to the checklist when submitting a new hwmon driver: only
some I2C addresses can be probed, others should not for safety
reasons.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Add pwm[4-7] and the associated pwm[4-7]_mode attributes.
Signed-off-by: Roger Lucas <vt8231@hiddenengine.co.uk>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Add hwmon driver for the Microchip TC74.
The TC74 is a single-input 8-bit I2C temperature sensor,
with +-2 degrees centigrade accuracy.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for the ntc thermistor NCPXXWF104 series.
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I2C address 0x37 may be used by EEPROMs, which can result in false
positives. Do not attempt to detect a chip at this address.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8620E is mostly compatible to IT7828F. Add generic support for it.
IT8620E supports up to 6 fan tachometers and 6 pwm controls.
Support for the 6th tachometer and for the additional pwm controls
are addded in separate patches.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8790E is a super-IO chip with three fan tachometers. It is mostly
compatible to IT8728F, but only supports three fan tachometers
instead of five.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The NCT7904D is a hardware monitor supporting up to 20 voltage sensors,
internal temperature sensor, Intel PECI and AMD SB-TSI CPU temperature
interface, up to 12 fan tachometer inputs, up to 4 fan control channels
with SmartFan.
Signed-off-by: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
[Guenter Roeck: Fixed whitespace errors, dropped redundant comment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8786E is mostly compatible with IT8771 / IT8772.
Parameters determined by testing various combinations.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Thomas Lorblanches <zlika_ese@hotmail.com>
[Guenter Roeck: merged from github, addressed review comments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TS3000GB0 has a new device ID (0x2913). Since IDT's datasheets suggest
that the upper 8 bit of the device ID reflect the chip ID and the lower
8 bit reflect the version number, modify the code to accept all chips
with ID 0x29xx.
Also add support for TS3001 and TSE2004.
Some of the datasheets for older chips are no longer available from
the IDT web site, so replace explicit links in the documentation with
a generic note.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8781F is mostly compatible to IT8782F. Major difference is that it only
supports four instead of six UART channels, and therefore does not share
the uart6 pins.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for "ina231" as compatible string, and update
Documentation and Kconfig accordingly.
Tested with the Exynos5422-based odroid-xu3 board which has on-board
INA231 sensors.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This attribute allows to configure the update interval of ina226. Although
the bus and shunt voltage conversion times remain hardcoded to 1.1 ms, we can
now modify said interval by changing the averaging rate.
While we're at it - add an additional variable to ina2xx_data, which holds
the current configuration settings - this way we'll be able to restore the
configuration in case of an unexpected chip reset.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The shunt resistance can only be set via platform_data or device tree. This
isn't suitable for devices in which the shunt resistance can change/isn't
known at boot-time.
Add a sysfs attribute that allows to read and set the shunt resistance.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TMP435 supports a range of I2C addresses, not just 0x4c.
Cc: Patrick Titiano <ptitiano@baylibre.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM95233 is similar to LM95234, but it only supports two
instead of four external temperature sensors.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM95235 is register compatible to LM95245.
Also update link to LM95245 data sheet, and drop the link to the
datasheet from the driver source to simplify code maintenance.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6792D is similar to NCT6791D. Only beep control and temperature
monitoring registers are different.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Document support for NCT6102D/NCT6104D/NCT6106D and NCT6791D.
Document that NCT5573D is compatible to NCT6775F with the same chip ID.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is basically a faster lm75 with improved (11 bit) resolution.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Added driver to support the 14F021P00 BMC Hardware Monitoring.
The BMC is a Board Management Controller including monitoring of the
board voltages.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds temperature monitoring support for F15h M60h processor.
- Add new pci device id for the relevant processor
- The functionality of REG_REPORTED_TEMPERATURE is moved to
D0F0xBC_xD820_0CA4 [Reported Temperature Control]
- So, use this to get CUR_TEMP value
- Since we need an indirect register access, protect this with
a mutex lock
- Add Kconfig, Doc entries to indicate support for this processor.
Signed-off-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
[Guenter Roeck: Declare new mutex and function static]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pwm-fan driver enables control of fans connected to PWM lines.
This driver uses the PWM framework, so it is compatible with all
PWM devices that provide drivers through the PWM framework.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
[Guenter Roeck: Last argument to devm_of_pwm_get is pointer, use NULL]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For TI power management chip TPS40422, READ_TEMPERATURE_2 command is supported on
page 1 of the chip, but the original driver(pmbus.c) only tried to detect this command
on page 0, this will lead to a result that the temperature sensor in page 1 couldn't
be detected. This change is to isolate the tps40422 driver from pmbus.c into a solo
front-end driver.
Signed-off-by: Zhu Laiwen <richard.zhu@nsn.com>
[Guenter Roeck: Dropped unnecessary license text (fixes checkpatch warning)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Not all supported chips support the entire I2C address range.
Only accept specific chips at the addresses supported by that chip.
Check for invalid values in conversion rate and status registers.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
This patch adds support for the ntc thermistor B57330V2103 from EPCOS.
Signed-off-by: Johannes Pointner <johannes.pointner@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Driver for the TI TMP103.
The TI TMP103 is similar to the TMP102. It differs from the TMP102
by having only 8 bit registers.
Signed-off-by: Heiko Schocher <hs@denx.de>
[linux@roeck-us.net: Select REGMAP_I2C in Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for Lattice's POWR1220 power manager IC. Read
access to all the ADCs on the chip are supported through the hwmon
sysfs files.
Signed-off-by: Scott Kanowitz <skanowitz@echo360.com>
[Guenter Roeck: Removed some extra ( )]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Murata Manufacturing Co., Ltd is the vendor for
NTC (Negative Temperature coefficient) based Thermistors.
But, the driver extensively uses "NTC" as the vendor name.
This patch corrects the vendor name also updates the
compatibility strings according to the vendor-prefix.txt
Note: Drivers continue to support the previous compatible strings
but further addition of these compatible strings in device tree
is deprecated.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Sensirion SHTC1 and compatible temperature and humidity
sensors.
Signed-off-by: Tomas Pop <tomas.pop@sensirion.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
New chip support to existing drivers:
Add support for STTS2004 and AT30TSE004 to jc42 driver
Add support for EMC1402/EMC1412/EMC1422 to emc1403 driver
Other notable changes:
Document hwmon kernel API
Convert jc42, lm70, lm75, lm77, lm83, lm92, max1619, tmp421,
and tmp102 drivers to use new hwmon API functions
Replace function macros in lm80, lm92, and jc42 drivers with
real code
Convert emc1403 driver to use regmap, add support for additional
attributes, and add device IDs for EMC1412, EMC1413, and EMC1414
Various additional cleanup and minor bug fixes in several drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dytt
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging into next
Pull hwmon updates from Guenter Roeck:
"New driver for NCT6683D
New chip support to existing drivers:
- add support for STTS2004 and AT30TSE004 to jc42 driver
- add support for EMC1402/EMC1412/EMC1422 to emc1403 driver
Other notable changes:
- document hwmon kernel API
- convert jc42, lm70, lm75, lm77, lm83, lm92, max1619, tmp421, and
tmp102 drivers to use new hwmon API functions
- replace function macros in lm80, lm92, and jc42 drivers with real
code
- convert emc1403 driver to use regmap, add support for additional
attributes, and add device IDs for EMC1412, EMC1413, and EMC1414
- various additional cleanup and minor bug fixes in several drivers"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (60 commits)
hwmon: (nct6775) Fix probe unwind paths to properly unregister platform devices
hwmon: (nct6683) Fix probe unwind paths to properly unregister platform devices
hwmon: (ultra45_env) Introduce managed version of kzalloc
hwmon: Driver for NCT6683D
hwmon: (lm80) Rearrange code to avoid forward declarations
hwmon: (lm80) Convert fan display function macros into functions
hwmon: (lm80) Convert voltage display function macros into functions
hwmon: (lm80) Convert temperature display function macros into functions
hwmon: (lm80) Normalize all temperature values to 16 bit
hwmon: (lm80) Simplify TEMP_FROM_REG
hwmon: (lm83) Convert to use devm_hwmon_device_register_with_groups
hwmon: (lm83) Rearange code to avoid forward declarations
hwmon: (lm83) Drop FSF address
hwmon: (max1619) Convert to use devm_hwmon_device_register_with_groups
hwmon: (max1619) Drop function macros
hwmon: (max1619) Rearrange code to avoid forward declarations
hwmon: (max1619) Drop FSF address
hwmon: (max1619) Fix critical alarm display
hwmon: (jc42) Add support for STTS2004 and AT30TSE004
hwmon: (jc42) Convert function macros into functions
...
The temp[1-*]_min_hyst sysfs attribute is already implemented by 3
hwmon drivers (adt7x10, lm77 and lm92) but was missing from the
standard interface.
Also add temp[1-*]_lcrit_hyst for consistency, even though no driver
implement that one for the time being.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Also fix links to datasheets for other supported sensors from
ST Microelectronics, and add links to several Atmel datasheets.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips in this chip series only support a single hysteresis value. Having
multiple writable hysteresis attributes is therefore confusing, since a single
write affects all hysteresis temperatures. Make all but one (temp1_crit_hyst)
read-only.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
With the driver now supporting several chip variants,
it is about time to document what is supported.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hwmon subsystem has been around for a while. Time to document
its kernel API.
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Updating the hysteresis value when updating the critical temperature limit
was following the rule of 'least surprise'. However, it had the undesirable
side effect of changing the hysteresis for all other attributes, which
defeats the purpose of least surprise. In addition, it could result in
invalid hysteresis values if the resulting hysteresis was too large. In such
cases the resulting hysteresis ended up changed anyway, which again defeats
the purpose. So drop that code and document the new behavior.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon updates from Jean Delvare:
"This includes a number of driver conversions to
devm_hwmon_device_register_with_groups, a few cleanups, and
support for the ITE IT8623E"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (it87) Add support for IT8623E
hwmon: (it87) Fix IT8603E define name
hwmon: (lm90) Convert to use hwmon_device_register_with_groups
hwmon: (lm90) Create all sysfs groups in one call
hwmon: (lm90) Always use the dev variable in the probe function
hwmon: (lm90) Create most optional attributes with sysfs_create_group
hwmon: Avoid initializing the same field twice
hwmon: (pc87360) Avoid initializing the same field twice
hwmon: (lm80) Convert to use devm_hwmon_device_register_with_groups
hwmon: (adm1021) Convert to use devm_hwmon_device_register_with_groups
hwmon: (lm63) Avoid initializing the same field twice
hwmon: (lm63) Convert to use devm_hwmon_device_register_with_groups
hwmon: (lm63) Create all sysfs groups in one call
hwmon: (lm63) Introduce 'dev' variable to point to client->dev
hwmon: (lm63) Add additional sysfs group for temp2_type attribute
hwmon: (f71805f) Fix author's address
Add support for the IT8623E found on Asus motherboards. It has same
hardware monitoring block as IT8603E.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Adding new PCI ID to support AMD F16 M30h processor (Mullins).
While at it, modify Kconfig and Doc files to reflect the
support for newer processors
Note: PCI ID for this processor will make it into pci_ids.h
as part of this patch:
http://marc.info/?l=linux-kernel&m=139291362126057&w=2
which should be pulled into 3.15 when merge window opens
(It currently sits in 'for-next' branch of bp.git-
https://git.kernel.org/cgit/linux/kernel/git/bp/bp.git/log/?h=for-next)
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The chip's programming interface is quite similar to LTC3880
and supports the same set of sensors.
Reviewed-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hysteresis register is shared among both temperature sensors.
This means changing one also affects the other. To avoid confusion,
established way to express this is to make only the first instance writable
and keep all other instances as read-only. Otherwise users may be
confused that changing the second writable value also affects the first,
while it is more obvious that a writable value may affect a different
read-only value.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
ADC128D818 is a System Monitor with Temperature Sensor. It is similar to LM80
and LM96080, but has 16 bit wide sensor registers and no fan speed monitoring.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC4260 is a Positive Voltage Hot Swap Controller.
The driver currently only supports voltage monitoring, not voltage control.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for IT8603E.
This closes bug #57861:
https://bugzilla.kernel.org/show_bug.cgi?id=57861
[JD: Fixes and clean-ups.]
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull hwmon fixes and updates from Jean Delvare:
"All lm90 driver fixes and improvements"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Documentation: dt: hwmon: Add OF document for LM90
hwmon: (lm90) Add power control
hwmon: (lm90) Add support for TI TMP451
hwmon: (lm90) Use enums for the indexes of temp8 and temp11
hwmon: (lm90) Add support to handle IRQ
hwmon: (lm90) Define status bits
hwmon: (lm90) Fix max6696 alarm handling
TI TMP451 is mostly compatible with ADT7461, except for
local temperature low byte and max conversion rate.
Add support to the LM90 driver.
Signed-off-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull hwmon fixes from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (emc6w201) Do not declare enum variable
hwmon: (w83792d) Update module author
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
w83792d was written by me in 2004, I'd like to update my first name
into my current one to keep consistent, and delete invalid address.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The temperature reporting interface stays the same, so we just
add the PCI-ID to the list.
Verified on AMD Olive Hill.
Signed-off-by: Wei Hu <wei@aristanetworks.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Corrected the word adventerous to adventurous.
Signed-off-by: Stefan Huber <steffhip@gmail.com>
Signed-off-by: Matthias Schid <aircrach115@gmail.com>
Signed-off-by: Simon Puels <simon.puels@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for ads1115 device to ads1015 driver.
Based on work of Emiliano Carnati <carnatiatebneuro.com>.
Tested on ARM CPU based board.
Signed-off-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for DS1631, DS1721, and DS1731 to ds1621 driver
Remove detect function from ds1621 driver as unreliable
Bug fixes in nct6775, iio_hwmon, and adm1021 drivers
Remove redundant platform_set_drvdata in various drivers
Add device tree support to ina2xx driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=OdGw
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver to support GMT G762/G763 pwm fan controllers
- add support for DS1631, DS1721, and DS1731 to ds1621 driver
- remove detect function from ds1621 driver as unreliable
- bug fixes in nct6775, iio_hwmon, and adm1021 drivers
- remove redundant platform_set_drvdata in various drivers
- add device tree support to ina2xx driver
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ds1621) Fix temperature rounding operations
hwmon: (nct6775) Drop unsupported fan alarm attributes for NCT6775
hwmon: (nct6775) Fix temperature alarm attributes
Add support for GMT G762/G763 PWM fan controllers
hwmon: (ina2xx) Add device tree support to pass the shunt resistor
hwmon: (ds1621) Update documentation
hwmon: (ds1621) Add DS1731 chip support to ds1621 driver
hwmon: (iio_hwmon) add alias table
hwmon: (adm1021) Do not create min sysfs attributes for LM84
hwmon: (ds1621) Remove detect function
hwmon: (ds1621) Add ds1631 chip support to ds1621 driver and documentation
hwmon: (ds1621) Add ds1721 update interval sysfs attribute
hwmon: (ds1621) Add ds1721 chip support
hwmon: (w83627ehf) Remove redundant platform_set_drvdata()
hwmon: (ntc_thermistor) Remove redundant platform_set_drvdata()
hwmon: (i5k_amb) Remove redundant platform_set_drvdata()
hwmon: (coretemp) Remove redundant platform_set_drvdata()
hwmon: (abituguru3) Remove redundant platform_set_drvdata()
GMT G762/763 fan speed PWM controller is connected directly to a fan
and performs closed-loop or open-loop control of the fan speed. Two
modes - PWM or DC - are supported by the chip. Introduced driver
provides various knobs to control the operations of the chip (via
sysfs interface). Specific characteristics of the system can be passed
either using board init code or via DT. Documentation for both the
driver and DT bindings are also provided.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding another way that is device tree to pass the shunt resistor
value to driver except for platform data.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[Guenter Roeck: Added missing of.h include]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replace some written information with tables to improve readability
and to simplify adding newer devices in the future.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These changes add DS1731 chip support to the ds1621 driver,
Kconfig, and documentation.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Due to a lack of device and vendor identification registers, the
Dallas/Maxim DS16xx devices cannot be uniquely detected, sometimes
resulting in false positives. Therefore, the detect function is
being removed in favor of explicit device instantiation.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add definitions, information, and code for ds1631 chip support
to the ds1621 driver.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ds1721 device can be configured for 9..12 bit resolutions;
add a sysfs attribute for userspace to configure this attribute.
The definition, description, details, and usage are shown in the
documentation and were crafted from an LM73 driver patch done by
Chris Verges & Guenter Roeck).
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update the ds1621 documentation, driver, and Kconfig with
ds1721 chip support.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Ever since commit 45f035ab9b ("CONFIG_HOTPLUG should be always on"),
it has been basically impossible to build a kernel with CONFIG_HOTPLUG
turned off. Remove all the remaining references to it.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Basically it's the same as the original DS75 but much faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Most LM75-compatible chips can either sample much faster or with a
much better resolution than the original LM75 chip. So far the lm75
driver did not let the user take benefit of these improvements. Do it
now.
I decided to almost always configure the chip to use the best
resolution possible, which also means the longest sample time. The
only chips for which I didn't are the DS75, DS1775 and STDS75, because
they are really too slow in 12-bit mode (1.2 to 1.5 second worst case)
so I went for 11-bit mode as a more reasonable tradeoff. This choice is
dictated by the fact that the hwmon subsystem is meant for system
monitoring, it has never been supposed to be ultra-fast, and as a
matter of fact we do cache the sampled values in almost all drivers.
If anyone isn't pleased with these default settings, they can always
introduce a platform data structure or DT support for the lm75. That
being said, it seems nobody ever complained that the driver wouldn't
refresh the value faster than every 1.5 second, and the change made
it faster for all chips even in 12-bit mode, so I don't expect any
complaint.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
- OpenFirmware/DeviceTree support for the Power Supply core: the core now
automatically populates supplied_from hierarchy from the device tree.
With these patches chargers and batteries can now lookup each other
without the board files support shim. Rhyland Klein at NVIDIA did the
work;
- New ST-Ericsson ABX500 hwmon driver. The driver is heavily using the
AB85xx core and depends on some recent changes to it, so that is why the
driver comes through the battery tree. It has an appropriate ack from
the hwmon maintainer (i.e. Guenter Roeck). Martin Persson at ST-Ericsson
and Hongbo Zhang at Linaro authored the driver;
- Final bits to sync AB85xx ST-Ericsson changes into mainline. The changes
touch mfd parts, but these were acked by the appropriate MFD maintainer
(i.e. Samuel Ortiz). Lee Jones at Linaro did most of the work and lead
the submission process.
Minor changes, but still worth mentioning:
- Battery temperature reporting fix for Nokia N900 phones;
- Versatile Express poweroff driver moved into drivers/power/reset/.
- Tree-wise: use devm_kzalloc() where appropriate;
- Tree-wise: dev_pm_ops cleanups/fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJRf1BPAAoJEGgI9fZJve1bwyoP/3Gv+qStzbN7mUtIVEvH3EAe
aVJwlODFzEZjk5xoiw7Dc8PuBE8O948hWOnQyCuUQ8+OfK6SyNIjexPYy3Z25a0F
cX9JMj7rtPWHvxo2q/YuKwBPZoxj/JIPyxwUT7akwXoHAV059fvcy9R1DfFX2Qur
hSP0NXTg+guvEpxGV4bC2l+LWZPmDFK9n0RsorttYaBvsiRDWl0c2TY2byofYlBw
++m/rI8Qgl8db8pKq/WDue62HtMt3kmZj6ZIgej3Wb0+GIRmYHMyPIyAkf82Wlw2
g2sGNPT7cstrSNOozegzJ7UghJObcYDFf10NCgvFMNjmAT1dAwdneQHEWy6Ek7pT
9X3e0LmaFqVbufFp4xFiLkMutsCLLTnGyXIbzs7RkTm3XBVIUqiDWtI6I6X44ohG
6PJn8vUlufu7owXrqFpgSBar2U1vfoQdhInmz4hbQeff0qn2nX/BGNwhxYptZ549
TudsI9WGzJ6fvYQ56zh6+BfiA0FmjhUiSKOtrXImrhxE6gUf3IOJyMQlkxLx5t8D
uuhBmO0J6kDi2lqF6alOEo+UDefJj4mUJn2tnIdis90+lNQlSV02GEtiwFT1zt1z
LFW0xshQkxZ4lMa28h35FB1/Z11ApUOe4Es+OKADDJhAnxdZzXcAwIRyPRRPgdsy
jTnJno+Kxk9wXLcekxVE
=5BdE
-----END PGP SIGNATURE-----
Merge tag 'for-v3.10' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Highlights:
- OpenFirmware/DeviceTree support for the Power Supply core: the core
now automatically populates supplied_from hierarchy from the device
tree. With these patches chargers and batteries can now lookup
each other without the board files support shim. Rhyland Klein at
NVIDIA did the work
- New ST-Ericsson ABX500 hwmon driver. The driver is heavily using
the AB85xx core and depends on some recent changes to it, so that
is why the driver comes through the battery tree. It has an
appropriate ack from the hwmon maintainer (i.e. Guenter Roeck).
Martin Persson at ST-Ericsson and Hongbo Zhang at Linaro authored
the driver
- Final bits to sync AB85xx ST-Ericsson changes into mainline. The
changes touch mfd parts, but these were acked by the appropriate
MFD maintainer (ie Samuel Ortiz). Lee Jones at Linaro did most of
the work and lead the submission process.
Minor changes, but still worth mentioning:
- Battery temperature reporting fix for Nokia N900 phones
- Versatile Express poweroff driver moved into drivers/power/reset/
- Tree-wide: use devm_kzalloc() where appropriate
- Tree-wide: dev_pm_ops cleanups/fixes"
* tag 'for-v3.10' of git://git.infradead.org/battery-2.6: (112 commits)
pm2301-charger: Fix suspend/resume
charger-manager: Use kmemdup instead of kzalloc + memcpy
power_supply: Populate supplied_from hierarchy from the device tree
power_supply: Add core support for supplied_from
power_supply: Define Binding for power-supplies
rx51_battery: Fix reporting temperature
hwmon: Add ST-Ericsson ABX500 hwmon driver
ab8500_bmdata: Export abx500_res_to_temp tables for hwmon
ab8500_{bmdata,fg}: Add const attributes to some data arrays
ab8500_bmdata: Eliminate CamelCase warning of some variables
ab8500_btemp: Make ab8500_btemp_get* interfaces public
goldfish_battery: Use resource_size()
lp8788-charger: Use PAGE_SIZE for the sysfs read operation
max8925_power: Use devm_kzalloc()
da9030_battery: Use devm_kzalloc()
da9052-battery: Use devm_kzalloc()
ds2760_battery: Use devm_kzalloc()
ds2780_battery: Use devm_kzalloc()
gpio-charger: Use devm_kzalloc()
isp1704_charger: Use devm_kzalloc()
...
TMP432 is similar to TMP431 with a second external temperature sensor.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Each of ST-Ericsson X500 chip set series consists of both ABX500 and DBX500
chips. This is ABX500 hwmon driver, where the abx500.c is a common layer for
all ABX500s, and the ab8500.c is specific for AB8500 chip. Under this designed
structure, other chip specific files can be added simply using the same common
layer abx500.c.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
NCT6775, NCT6776, and NCT6779 have a number of variants with the same
chip ID but different chip labels. Add text "or compatible" to the
message displayed when the driver is loaded and rephrase the Kconfig
entry to reflect that it also supports compatible chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TMP431 is compatible to TMP401.
Also add support for additional I2C addresses supported by TMP411B
and TMP411C.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
So far the driver reported the voltage on VAUX as "vout2". This was not
entirely appropriate as it is not an output voltage, and complicates
the code. Use the new virtual "VMON" register set and report the voltage
as "vmon" instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some sysfs attributes are only supported on LTC2978 and not on LTC3880.
Update documentation to reflect which attributes are supported for which chips.
Output current attributes supported on LTC3880 were described as providing
input current values. Fix text to reflect that the attributes provide output
current values.
"reset history" attribute descriptions were misleading and seemed to imply
that all history was reset when writing a single attribute. Replace with more
accurate text.
Replace 'internal temperature" with "chip temperature". Temperature limits
not only apply to the chip temperature, but also to external temperatures
on LTC3880, so remove the word "chip" from the attribute description.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The NCT677X series support weighted fan control. In this mode, a secondary
temperature source is used in addition to the primary temperature source to
control fan speed. Add support for this feature.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver will replace the w83627ehf driver for NCT6775F and NCT6776F,
and provides support for NCT6779D.
This patch provides support for voltage monitor attributes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7310/adt7320 is the SPI version of the adt7410/adt7420. The register map
layout is a bit different, i.e. the register addresses differ between the two
variants, but the bit layouts of the individual registers are identical. So both
chip variants can easily be supported by the same driver. The issue of non
matching register address layouts is solved by a simple look-up table which
translates the I2C addresses to the SPI addresses.
The patch moves the bulk of the adt7410 driver to a common module that will be
shared by the adt7410 and adt7310 drivers. This common module implements the
driver logic and uses a set of virtual functions to perform IO access. The
adt7410 and adt7310 driver modules provide proper implementations of these IO
accessor functions for I2C respective SPI.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7410 driver supports the ADT7420, but its documentation file
makes no mention of that. Add this refrence, and a brief a description
of the differences between the ADT7410 and the ADT7420.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Links to datasheets are no longer valid. Provide links to product information
instead (which provides links to the datasheets and is hopefully more
persistent).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Most of the hwmon driver documentation still listed my old invalid e-mail
address. Fix it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
MAX34460 is a PMBus 12-Channel Voltage Monitor & Sequencer.
MAX34461 is a PMBus 16-Channel Voltage Monitor & Sequencer.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the ZL6100 compatible chips support monitoring a separate voltage pin,
VMON (ZL2004) or VDRV (ZL91xx). Report it as in2 / vmon.
The chips support implicit warning limits for VMON/VDRV, as percentage of the
respective critical voltage. Support by reading/writing the critical voltages
and calculating the associated warning voltages.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the TI / Burr-Brown INA209 voltage / current / power
monitor.
Cc: Paul Hays <haysp@magma.net>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for temp1_min_alarm and temp1_max_alarm
Signed-off-by: Chris Verges <kg4ysn@gmail.com>
[linux@roeck-us.net: cleanup; dropped platform data and interrupt support]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The LM73 supports four A/D conversion resolutions. The default used by
the existing lm73 driver is the chip's default, 11-bit (0.25 C/LSB).
This patch enables changing of this resolution from userspace via the
update_interval sysfs attribute. Full details on usage are included in
Documentation/hwmon/lm73.
Signed-off-by: Chris Verges <kg4ysn@gmail.com>
[linux@roeck-us.net: cleanup]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Assume that IT8771E and IT8772E are fully compatible with IT8728F.
IT8771E support contributed by Kelly Anderson.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Add support for MAX6581, MAX6602, MAX6622, MAX6636, MAX6689, MAX6693,
MAX6694, MAX6697, MAX6698, and MAX6699 temperature sensors
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
SENSORS_LIMIT and clamp_val have the same functionality, so retire SENSORS_LIMIT
as it is no longer needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
IT8721 and IT8728 support Intel PECI temperature reporting. Each sensor
can be programmed to display the temperature reported on the PECI interface.
If configured for Intel PECI, the driver reported the wrong sensor type for
the respective thermal sensor. Fix the code to correctly report it as
"Intel PECI (6)".
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
This is the HWMON patch for DA9055 PMIC and has got dependency on the
DA9055 MFD core.
This patch monitors the DA9055 PMIC's ADC channels vddout, junction temperature
and auxiliary channels.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Guenter Roeck: Dropped __devinit, __devexit, __devexit_p]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADS7830 device is almost the same as the ADS7828,
except that it does 8-bit sampling, instead of 12-bit.
This patch extends the ads7828 driver to support this chip.
Signed-off-by: Guillaume Roguez <guillaume.roguez@savoirfairelinux.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As there is no reliable way to identify the chip, it is preferable to
remove the detect callback, to avoid misdetection.
Module parameters are not worth it here, so let's get rid of them and
add an ads7828_platform_data structure instead.
Clean the code by removing unused macros, fixing coding style issues,
avoiding function prototypes and using convenient macros such as
module_i2c_driver().
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
hwmon framework driver for Versatile Express sensors, providing
information about board level voltage (only when regulator driver
is not configured), currents, temperature and power/energy usage.
Labels for the values can be defined as DT properties.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
TjMax for the CE4100 series of Atom CPUs was previously reported to be
110 degrees C.
cpuinfo logs on the web show existing CPU types CE4110, CE4150, and CE4170,
reported as "model name : Intel(R) Atom(TM) CPU CE41{1|5|7}0 @ 1.{2|6}0GHz"
with model 28 (0x1c) and stepping 10 (0x0a). Add the three known variants
to the tjmax table.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
cc: stable@vger.kernel.org
Acked-by: Jean Delvare <khali@linux-fr.org>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Jean Delvare <khali@linux-fr.org>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Rob Landley <rob@landley.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull ACPI & Thermal updates from Len Brown:
"The generic Linux thermal layer is gaining some new capabilities
(generic cooling via cpufreq) and some new customers (ARM).
Also, an ACPI EC bug fix plus a regression fix."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (30 commits)
tools/power/acpi/acpidump: remove duplicated include from acpidump.c
ACPI idle, CPU hotplug: Fix NULL pointer dereference during hotplug
cpuidle / ACPI: fix potential NULL pointer dereference
ACPI: EC: Add a quirk for CLEVO M720T/M730T laptop
ACPI: EC: Make the GPE storm threshold a module parameter
thermal: Exynos: Fix NULL pointer dereference in exynos_unregister_thermal()
Thermal: Fix bug on cpu_cooling, cooling device's id conflict problem.
thermal: exynos: Use devm_* functions
ARM: exynos: add thermal sensor driver platform data support
thermal: exynos: register the tmu sensor with the kernel thermal layer
thermal: exynos5: add exynos5250 thermal sensor driver support
hwmon: exynos4: move thermal sensor driver to driver/thermal directory
thermal: add generic cpufreq cooling implementation
Fix a build error.
thermal: Fix potential NULL pointer accesses
thermal: add Renesas R-Car thermal sensor support
thermal: fix potential out-of-bounds memory access
Thermal: Introduce locking for cdev.thermal_instances list.
Thermal: Unify the code for both active and passive cooling
Thermal: Introduce simple arbitrator for setting device cooling state
...
Conflicts:
drivers/staging/omap-thermal/omap-thermal-common.
OMAP supplied dummy TC1 and TC2,
at the same time that the thermal tree removed them
from thermal_zone_device_register()
drivers/thermal/cpu_cooling.c b/drivers/thermal/cpu_cooling.c
propogate the upstream MAX_IDR_LEVEL re-name
to prevent a build failure
Previously-fixed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Len Brown <len.brown@intel.com>
This movement is needed because the hwmon entries and corresponding sysfs
interface is a duplicate of utilities already provided by
driver/thermal/thermal_sys.c. The goal is to place it in thermal folder
and add necessary functions to use the in-kernel thermal interfaces.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: SangWook Ju <sw.ju@samsung.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This Patch adds support for mcp3221 chip to the
mcp3021 driver.
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
INA220 is register compatible to INA219, and INA230 is register compatible to
INA226, so all we need to do is to add name aliases for those two chips.
Cc: Lothar Felten <l-felten@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Add support for LM74 and LM71 to LM70 driver.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Removing the 3wire limitation on LM70 as the component also allows
operation on 4wire SPI bus
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MAX197 is an A/D converter, made by Maxim. This driver currently
supports the MAX197, and MAX199. They are both 8-Channel, Multi-Range,
5V, 12-Bit DAS with 8+4 Bus Interface and Fault Protection.
The available ranges for the MAX197 are {0,-5V} to 5V, and {0,-10V} to
10V, while they are {0,-2V} to 2V, and {0,-4V} to 4V on the MAX199.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch brings basic support for the Analog Devices ADT7410 temperature
sensor. The following functionality has been implemented:
* get current temperature
* get/set minimum, maximum and critical temperature
* get/set hysteresis
* get alarm events for minimum, maximum and critical temperature
All implemented sysfs attributes have been sucessfully tested at temperatures
of 15°C to 40°C.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This is a new driver for the Honeywell Humidicon HIH-6130/HIH-6131 humidity sensor.
The driver is based on the existing Sensiron sht21 driver with the necessary changes
to the probe, update_measurements and conversion functions necessary to use the
Honeywell sensors.
There's no difference between the 6130 & 6131 other than the 6131 having an external
condensation filter attached.
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
devres functions are the preferred means to allocate resources in hwmon drivers.
Document it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
The DA9052 PMIC provides an Analogue to Digital Converter with 10 bits
resolution and 10 channels.
This patch monitors the DA9052 PMIC's ADC channels mostly for battery
parameters like battery temperature, junction temperature, battery
current etc.
This patch is functionally tested on Samsung SMDKV6410
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Guenter Roeck: __init --> __devinit for probe function]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Document the Atom series D2000 and N2000 (Cedar Trail) as being supported.
List and set TjMax for those series.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Document the new Atom series (Tunnel Creek and Medfield) as being
supported, and list TjMax for the Atom E600 series.
Also enable the Atom tjmax heuristic for these Atom CPU models.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
New driver for INA219 and INA226, added support for IT8782F and IT8783E/F to
it87 driver, plus cleanups in a couple of drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=ZX6H
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New driver for INA219 and INA226, added support for IT8782F and
IT8783E/F to it87 driver, plus cleanups in a couple of drivers."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (it87) Make temp3 attribute conditional for IT8782F
hwmon: (it87) Convert to use devm_kzalloc and devm_request_region
hwmon: INA219 and INA226 support
hwmon: (it87) Create voltage attributes only if voltage is enabled
hwmon: (ntc_thermistor) Fix checkpatch warning
hwmon: (ntc_thermistor) Optimize and fix build warning
hwmon: (ntc_thermistor) Return error code from hwmon_device_register
hwmon: (ntc_thermistor) Convert to devm_kzalloc
hwmon: (ad7314) Remove unused defines, and rename OFFSET to SHIFT
acpi_power_meter: clean up code around setup_attrs
acpi_power_meter: drop meter_rw_attrs, use common meter_attrs
acpi_power_meter: remove duplicate code between register_{ro,rw}_attrs
acpi_power_meter: use a {RW,RO}_SENSOR_TEMPLATE macro to clean things up
acpi_power_meter: use the same struct {rw,ro}_sensor_template for both
hwmon: use module_pci_driver
hwmon: (it87) Add support for IT8782F and IT8783E/F
Add support for the Texas Instruments INA219 and INA226 power monitors.
Signed-off-by: Lothar Felten <l-felten@ti.com>
[guenter.roeck@ericsson.com: formatting cleanup; check for smbus word data;
select PGA=8 for INA219]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Merge with latest Linus' tree, as I have incoming patches
that fix code that is newer than current HEAD of for-next.
Conflicts:
drivers/net/ethernet/realtek/r8169.c
The on-chip northbridge's temperature sensor of the upcoming
AMD Trinity CPUs works the same as for the previous CPUs.
Since it has a different PCI-ID, we just add the new one to the list
supported by k10temp.
This allows to use the k10temp driver on those CPUs.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add I2C driver for MCP3021 that is an ADC chip from Microchip.
The MCP3021 is a successive approximation A/D converter (ADC)
with 10-bit resolution.
The driver export the value of Vin to sysfs, the voltage unit is
mV. Through the sysfs interface, lm-sensors tool can also display
Vin voltage.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Based on a patch by David Jander that mostly did s/mc13783/mc13xxx/ .
Additionally use dev_get_drvdata instead of to_platform_device +
platform_get_drvdata in mc13783_adc_read (spotted by Jean Delvare).
Cc: David Jander <david.jander@protonic.nl>
Signed-off-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
GMT G781 is a ADM1032-compatible temperature sensor chip.
Add support to the LM90 driver.
Cc: Mike Gorchak <lestat@i.com.ua>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull trivial tree from Jiri Kosina:
"It's indeed trivial -- mostly documentation updates and a bunch of
typo fixes from Masanari.
There are also several linux/version.h include removals from Jesper."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
kcore: fix spelling in read_kcore() comment
constify struct pci_dev * in obvious cases
Revert "char: Fix typo in viotape.c"
init: fix wording error in mm_init comment
usb: gadget: Kconfig: fix typo for 'different'
Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
writeback: fix typo in the writeback_control comment
Documentation: Fix multiple typo in Documentation
tpm_tis: fix tis_lock with respect to RCU
Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
Doc: Update numastat.txt
qla4xxx: Add missing spaces to error messages
compiler.h: Fix typo
security: struct security_operations kerneldoc fix
Documentation: broken URL in libata.tmpl
Documentation: broken URL in filesystems.tmpl
mtd: simplify return logic in do_map_probe()
mm: fix comment typo of truncate_inode_pages_range
power: bq27x00: Fix typos in comment
...
Add support for the watchdog integrated into the SMSC SCH5627 and
SCH5636 superio-s. Since the watchdog is part of the hwmon logical device
and thus shares ioports with it, the watchdog driver is integrated into the
existing hwmon drivers for these.
Note that this version of the watchdog support for sch56xx superio-s
implements the watchdog chardev interface itself, rather then relying on
the recently added watchdog core / watchdog_dev. This is done because
currently some needed functionality is missing from watchdog_dev, as soon
as this functionality is added (which is being discussed on the
linux-watchdog mailinglist), I'll convert this driver over to using
watchdog_dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[guenter.roeck@ericsson.com: Added missing linux/slab.h include]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
We don't really use or need separate device IDs for the various JC42.4 compliant
chips, so remove them and just stick with jc42.
Also update a datasheet references for SE98A, STTS424, and STTS424E02.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
ZL9101M and ZL9117M are compatible to ZL6100. Add support to the zl6100 driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
MDT040 is supported by the generic PMBus driver. Add device ID and reference to
datasheet. Also mention Lineage Power device support in Kconfig.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TPS40400 and TPS40422 are supported by the generic PMBus driver.
Add device IDs and data sheet references.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX34440 and compatibles support reporting the lowest measured output voltage.
Add support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Add detection of the National Semiconductor (now Texas Instruments)
LM96080. It is functionally compatible with the LM80 but detection is
completely different.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Intersil reports that all chips supported by the zl6100 driver require
an interval between chip accesses, even ZL2004 and ZL6105 which were thought
to be safe.
Reported-by: Vivek Gani <vgani@intersil.com>
Cc: stable@vger.kernel.org # 3.2+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add description of pwm[1-4]_start_output, pwm[1-4]_step_output,
pwm[1-4]_stop_output, and pwm[1-4]_max_output attributes to driver
documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Properly set the source of temp2 for the W83627UHG. Also fix a
comment right before that, and document the W83627UHG as reporting up
to 3 temperatures.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
These are fully compatible with Jedec JC 42.4 as far as I can see.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The temp[1-*]_type attribute reports the temperature sensor type. Sensor type 1
is described as "PII/Celeron Diode", which is quite restrictive; other CPUs
may also have an embedded temperature sensor diode with similar characteristics.
Change description to "CPU embedded diode" to be more generic.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Until we get a datasheet for the IT8728F, treat it as fully compatible
with the IT8721F, as it seems to work reasonably well.
This closes kernel bug #27262.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The LM63 and compatible devices have a lookup table to control the fan
speed automatically. Expose it in sysfs. Values are cached for 5
seconds, independently of the other register values to avoid slowing
down "sensors". We might make the table values writable in the future.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
On the LM64, the tachometer function has a dedicated pin and fan speed
monitoring is always enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
On LM96163, the external temperature sensor type is configurable to
either a thermal diode or a 3904 transistor. The chip reports a wrong
temperature if misconfigured. Add writable attribute to support it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The update interval is configurable on LM63 and compatibles. Add
support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
LM96163 is an enhanced version of LM63 with improved PWM resolution. Add chip
detection code as well as support for improved PWM resolution if the chip is
configured to use it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for Ericsson BMR450, BMR451, BMR462, BMR463, and BMR464, which are
based on ZL2005 and ZL2008, to zl6100 driver. Remove BMR450 and BMR451 device
IDs from generic PMBus driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add explicit support for ZL2005. Functionality is almost the same as with other
Zilker Labs / Intersil chips, but limit register detection does not work reliably.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
This is essentially a stripped down version of the W83627DHG. Noticeable
difference is that it is still powered with +5V, as older models, even
though the ADC resolution is 8 mV as newer models have.
Thanks to Ulf Bruman (Saab Group) for doing all the testing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Explain why clones of the LM75 are generally not detected by the
driver, and why this isn't going to change. Also update the
documentation to reflect the list of chip names currently supported by
the driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add datasheet reference and device ID for ADT75.
The ADT75, like some other LM75 derivatives, needs to be instantiated
using methods 1, 2, or 4.
For more information see Documentation/i2c/instantiating-devices.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add device IDs and reference to datasheets for Lineage Power DC-DC converters.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
The LTC3880 PMBus command set is comparable to LTC2978. Add support for it
to the LTC2978 driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Provide explicit driver for LTC2978 to enable support for minimum and peak
attributes. Remove ltc2978 chip id from generic pmbus driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Driver for AD7314, ADT7301, and ADT7302, ported from IIO.
Currently dropped power down mode support.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
[guenter.roeck@ericsson.com: Added MODULE_DEVICE_TABLE]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Provide more documentation describing PMBus driver functionality and the API
between the PMBus core driver and PMBus chip drivers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
This patch allows to read temperature
from TMU(Thermal Management Unit) of SAMSUNG EXYNOS4 series of SoC.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
ADM1276 is mostly compatible to ADM1275, with added support for input power
measurement. Add support for it to the ADM1275 driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
ADM1275 supports a second current limit, which can be configured as either lower
or upper limit. Add support for it and report it as either lower or upper
critical current limit.
Also replace error return code EINVAL for unsupported pages with ENXIO as this
is more appropriate for the observed condition.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
With commit c814a4c7c4, the meaning of tempX_max
was changed. It no longer returns the value of bits 8:15 of
MSR_IA32_TEMPERATURE_TARGET, but instead returns the value of CPU threshold
register T1. tempX_max_hyst was added to reflect the value of temperature
threshold register T0.
As it turns out, T0 and T1 are used on some systems, presumably by the BIOS.
Also, T0 and T1 don't have a well defined meaning. The thresholds may be used
as upper or lower limits, and it is not guaranteed that T0 <= T1. Thus, the new
attribute mapping does not reflect the actual usage of the threshold registers.
Also, register contents are changed during runtime by an entity other than the
hwmon driver, meaning the values cached by the driver do not reflect actual
register contents.
Revert most of c814a4c7c4 to address the problem.
Support for T0 and T1 will be added back in with a separate commit, using new
attribute names.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
On old CPUs (and even some recent Atom CPUs) TjMax can't be read from
the CPU registers, so it is guessed by the driver using a complex
heuristic which isn't reliable. So let users who know their CPU's
TjMax pass it as a module parameter.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The chips supported by the max16065 driver should not be accessed using direct
i2ctools commands. Add warning to driver documentation to alert users.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (24 commits)
hwmon: (lm90) Refactor reading of config2 register
hwmon: (lm90) Make SA56004 detection more robust
hwmon: (lm90) Simplify handling of extended local temp register
hwmon: (pmbus) Add client driver for LM25066, LM5064, and LM5066
hwmon: (max34440) Add support for peak attributes
hwmon: (max8688) Add support for peak attributes
hwmon: (max16064) Add support for peak attributes
hwmon: (adm1275) Add support for peak attributes
hwmon: (pmbus) Add support for peak attributes
hwmon: Add new attributes to sysfs ABI
hwmon: (pmbus) Strengthen check for status register existence
hwmon: (pmbus) Add support for virtual pages
hwmon: (pmbus) Support reading and writing of word registers in device specific code
hwmon: (pmbus) Increase attribute name size
hwmon: (pmbus) Add ADP4000, NCP4200 and NCP4208 to list of supported devices
hwmon: (pmbus) Add support for VID output voltage mode
hwmon: (pmbus) Move PMBus drivers to drivers/hwmon/pmbus
hwmon: (coretemp) Add core/pkg threshold support to Coretemp
hwmon: (lm95241) Add support for LM95231
hwmon: LM95245 driver
...
Add support for voltage, current, and temperature peak (historic maximum)
attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for voltage and temperature peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for voltage and current peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add the following attributes to the sysfs ABI.
in[0-*]_average
in[0-*]_lowest
in[0-*]_highest
in[0-*]_reset_history
in_reset_history
curr[1-*]_average
curr[1-*]_lowest
curr[1-*]_highest
curr[1-*]_reset_history
curr_reset_history
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add ADP4000, NCP4200 and NCP4208 to the list of devices supported by the generic
PMBus driver, and add device IDs to enable explicit instantiation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch adds the core and pkg support to coretemp.
These thresholds can be configured via the sysfs interfaces tempX_max
and tempX_max_hyst. An interrupt is generated when CPU temperature reaches
or crosses above tempX_max OR drops below tempX_max_hyst.
This patch is based on the documentation in IA Manual vol 3A, that can be
downloaded from here:
http://download.intel.com/design/processor/manuals/253668.pdf
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
A hwmon driver for the National Semiconductor LM95245 dual temperature
sensors chip.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for Philips SA56004, an LM86 compatible temperature sensor.
Signed-off-by: Stijn Devriendt <sdevrien@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for NTC Thermistor series. In this release, the
following thermistors are supported: NCP15WB473, NCP18WB473, NCP03WB473,
and NCP15WL333. This driver is based on the datasheet of MURATA.
The driver in the patch does conversion from the raw ADC value
(either voltage or resistence) to temperature. In order to use
voltage values as input, the circuit schematics should be provided
with the platform data. A compensation table for each type of thermistor
is provided for the conversion.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds support for MAX1668 and compatible temperature sensors.
Signed-off-by: David George <david.george@ska.ac.za>
[guenter.roeck@ericsson.com: minor cleanup of probe error path]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Declare myself the maintainer of the lm78 driver. I still have a
running system with one of these chips.
Also count myself as a co-author of the driver. With 34 commits over
6 years, it seems fair.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds a new driver for SMSC SCH5636 Super I/O chips.
The chips include an embedded microcontroller for hardware monitoring
solutions, allowing motherboard manufacturers to create their own
custom hwmon solution based upon the SCH5636.
Currently the sch5636 driver only supports the Fujitsu Theseus SCH5636
based hwmon solution. The sch5636 driver runs a sanity check on
loading to ensure it is dealing with a Fujitsu Theseus and not with
another custom SCH5636 based hwmon solution.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add some CPU series IDs and links to the Fam12h datasheets.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The F71869A is almost the same as the F71869F/E, except that it has
the normal number of temp and pwm zones for a F71882FG derived chip,
rather then the limited number of the F71869F/E.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Max Baldwin <archerseven@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is a new driver for the SMSC EMC6W201 hardware monitoring device.
The device is functionally close to the EMC6D100 series, but is
register-incompatible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Harry G McGavran Jr <w5pny@arrl.net>
Tested-by: Jeff Rickman <jrickman@myamigos.us>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The MAX6650 has only one fan input.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: "Hans J. Koch" <hjk@hansjkoch.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
MAX6650 device detection is unreliable, we got reports of false
positives. We now have many ways to let users instantiate the devices
explicitly, so unreliable detection should be dropped.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: "Hans J. Koch" <hjk@hansjkoch.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This CPU family provides NB register values to gather following
TDP information
* ProcessorPwrWatts: Specifies in Watts the maximum amount of power
the processor can support.
* CurrPwrWatts: Specifies in Watts the current amount of power being
consumed by the processor.
This driver provides
* power1_crit (ProcessorPwrWatts)
* power1_input (CurrPwrWatts)
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
AMDs upcoming CPUs use the same mechanism for the internal
temperature reporting as the Fam10h CPUs, so we just needed to add
the appropriate PCI-ID to the list.
This allows to use the k10temp driver on those CPUs.
While at it change the Kconfig entry to be more generic.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
After the merge of pkgtemp functionality into the coretemp driver,
the pkgtemp driver is no longer necessary. Remove it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch merges the pkgtemp with coretemp driver.
The sysfs interfaces for all cores in the same pkg
are shown under one directory, in hwmon. It also
supports CONFIG_HOTPLUG_CPU. So, the sysfs interfaces
are created when each core comes online and are
removed when it goes offline.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
[guenter.roeck@ericsson.com: Fixed section reference errors]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for Analog Devices ADM1275 Hot-Swap Controller and Digital Power
Monitor
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Hardware monitoring support for TI UCD90120, UCD90124, UCD9090, and UCD90910
Sequencer and System Health Controllers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
This patch adds hardware monitoring support for TI UCD9220, UCD9222, UCD9224,
UCD9240, UCD9244, UCD9246, and UCD9248 Digital PWM System Controllers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
This patch adds hardware monitoring support for Maxim MAX16065, MAX16066,
MAX16067, MAX16068, MAX16070, and MAX16071 flash-configurable system managers
with nonvolatile fault registers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
The sht15 sensor allows validating exchanges to and from the device
using a crc8 function. An utility function to reverse a byte has also
been added.
Signed-off-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* Add support for:
- Heater.
- End of battery notice.
- Ability not to reload from OTP.
- Low resolution (12bit temp, 8bit humidity).
* Add an utility function to read individual bytes from the device.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* Add a documentation file for the device.
* Respect a bit more the kernel-doc syntax.
* Rename some variables for clarity.
* Use bool type for flags.
* Use an enum for states (actions being done).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
MAX6642 is a SMBus-Compatible Remote/Local Temperature Sensor with
Overtemperature Alarm from Maxim.
Signed-off-by: Per Dalen <per.dalen@appeartv.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Recent Xeon processor thermal sensors are supported by the coretemp
driver and not the adm1021 driver. Only one old generation of Xeon
processors (the first Netburst ones) are supported by the adm1021
driver.
Reported-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The lm90 driver's attribute update interval is configurable.
Reflect this information in the driver documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for ADT7461A and NCT1008 to the lm90 driver.
Both chips have identical functionality and report the same manufacturing ID
and device ID values.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
MAX34440 and MAX34441 have their own driver, thus there should be explicit
documentation instead of mentioning the chips in the generic PMBus driver
documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Linus Torvalds