Fix 2.6.12 CONFIG_ACPI=n build regression.
CONFIG_ACPI_BOOT shall be set only if CONFIG_ACPI.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Delete quirk_via_bridge(), restore quirk_via_irqpic() -- but now
improved to be invoked upon device ENABLE, and now only for VIA devices
-- not all devices behind VIA bridges.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The original pwc author raised some questions about the reverse
engineering of the decompressor algorithms used in the pwc driver.
Having done some detailed investigation it appears those concerns that
clean room policy was not followed are reasonable. I've also had a
friendly discussion with Philips to ask their view on this.
This removes the problem items of code which reduces the pwc
functionality in the kernel a little but leaves all the framework for
setup that will be needed for decompressors in user space (where they
eventually belong). This change set is designed to be the minimal risk
change set given that 2.6.12 is hopefully close to hand, with a view to
merging the much updated pwc code in 2.6.13 series kernels.
Someone else can then redo the decompressors properly (clean room) in
user space.
Note that while its easy to say that it should have been caught earlier,
but the violation was really only obvious to someone who had access to
both the proprietary source and the 'GPL' source.
A new driver bnx2 for Broadcom bcm5706 is available.
The patch also includes new 1000BASE-X advertisement bit definitions in
mii.h
Thanks to David Miller and Jeff Garzik for reviewing and their valuable
feedback.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correcting the list traversal makes the problem go away.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Marcello Maggioni <hayarms@gmail.com>
Problem: Some drives (NEC 3500, TDK 1616N, Mad-dog MD-16XDVD9, RICOH
MP5163DA, Memorex DVD9 drive and IO-DATA's too for sure), if a
CD/DVD is inserted into the tray when the system is booted and if
before the OS bootup the BIOS checked for the presence of a bootable
CD/DVD into the drive, during the IDE probe phase the drive may
result busy and remain so for the next 25/30 seconds . This cause the
drive to be skipped during the booting phase and not begin usable
until the next reboot (if the reboot goes well and the drive doesn't
timeout again).
Solution: Rising the timeout time from 10 seconds to 35 seconds
(during these 35 seconds every drive should wake up for sure
according to the tests I've done).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
From: Stuart Hayes <Stuart_Hayes@dell.com>
The system can panic with a null pointer dereference using ide-scsi if
PIO is being done on scatter gather pages that are in high memory,
because page_address() returns 0. We are actually seeing this using a
tape drive. This patch will kmap_atomic() the pages before performing
PIO.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
* add ide_bus_match() and export ide_bus_type
* split ide_remove_driver_from_hwgroup() out of ide_unregister()
* move device cleanup from ide_unregister() to drive_release_dev()
* convert ide_driver_t->name to driver->name
* convert ide_driver_t->{attach,cleanup} to driver->{probe,remove}
* remove ide_driver_t->busy as ide_bus_type->subsys.rwsem
protects against concurrent ->{probe,remove} calls
* make ide_{un}register_driver() void as it cannot fail now
* use driver_{un}register() directly, remove ide_{un}register_driver()
* use device_register() instead of ata_attach(), remove ata_attach()
* add proc_print_driver() and ide_drivers_show(), remove ide_drivers_op
* fix ide_replace_subdriver() and move it to ide-proc.c
* remove ide_driver_t->drives, ide_drives and drives_lock
* remove ide_driver_t->drivers, drivers and drivers_lock
* remove ide_drive_t->driver and DRIVER() macro
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
When testing ATAPI PIO data transfer on the ppc64 platform, __atapi_pio_bytes() got zero when
sg_dma_len() is used. I checked the <asm-ppc64/scatterlish.h>, the struct scatterlist is defined as:
struct scatterlist {
struct page *page;
unsigned int offset;
unsigned int length;
/* For TCE support */
u32 dma_address;
u32 dma_length;
};
#define sg_dma_address(sg) ((sg)->dma_address)
#define sg_dma_len(sg) ((sg)->dma_length)
So, if the scatterlist is not DMA mapped, sg_dma_len() will return zero on ppc64.
The same problem should occur on the x86-64 platform.
On the i386 platform, sg_dma_len() returns sg->length, that's why the problem does not occur on an i386.
Changes:
- Use sg->length if the scatterlist is not DMA mapped (yet).
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
This patch shows the correct locations of the heat sensors present in iBook
and PowerBooks G4, instead of displaying them as being on CPU and GPU
(which is not always the case).
Signed-off-by: Colin Leroy <colin@colino.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch limits therm_adt746x to currently existing fan controllers in
Apple laptops. It may avoid problems with future hardware.
Signed-off-by: Colin Leroy <colin@colino.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make MTU field in SA PathRecord and MCMemberRecord a u8 rather than an enum
to avoid complications with endianness.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Free all unclaimed MAD receive buffers when userspace closes our file so we
don't leak memory.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Check if a client passes a NULL callback into an SA query, and if so, never
call back. This fixes an oops if someone unloads ib_ipoib and ib_sa in
rapid succession. ib_ipoib does an MCMember delete with a NULL callback
and 0 timeout on unload, which is usually fine since the delete completes
successfully. However, if ib_sa is unloaded immediately afterwards, the
delete will be canceled and ib_sa will try to call the (now already
unloaded) ib_ipoib module back with the cancel completion, which triggers
the oops.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It looks like the recent IPMI patches had some -mm-onlyisms.
Signed-off-by: Neil Horman <nhorman@redhat.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't try to access the i2c bus if the register wasn't successful.
Signed-off-by: Gerd Knorr <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This has been sitting for a while, and is causing lots of grief for
people burning CDs. It relaxes the dma restriction for ide-cd,
requiring only the length to be 32-byte aligned, address should be fine
at normal double word alignment.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's a bigger Speedtouch update coming your way after 2.6.12 but in
the meantime, let's at least make it automatically resync if the DSL
signal is lost.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a c99ism.
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 'if' clause for ULI526X in tulip_mdio_write allows for
spin_unlock_irqrestore to be called twice for tp->mii_lock. I believe
this is caused by the unintentional omission of a return at the end
of that clause. This patch adds that return.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As a result of the split of the kobject-registration and the
corresponding hotplug event, the order of events for device_add() has
changed. This restores the old order, cause it confused some userspace
applications.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Len Brown