Commit b9a50f7490 ("ARM: 7450/1: dcache: select DCACHE_WORD_ACCESS for
little-endian ARMv6+ CPUs") added support for word-at-time path
comparisons, relying on the ability to perform unaligned loads with
negligible performance impact in hardware.
For nommu configurations without MPU support, this is unpredictable and
so we should fall back to the byte-by-byte routines.
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Recent ARMv7 toolchains assume that unaligned memory accesses will not
fault and will instead be handled by the processor.
For the nommu case (without an MPU), memory will be treated as
strongly-ordered and therefore unaligned accesses may fault regardless
of the SCTLR.A setting.
This patch passes -mno-unaligned-access to GCC when compiling for nommu
targets, preventing the generation of unaligned memory access in the
kernel.
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch keeps disabled the strict alignment CP15 bit for
all armv6 and armv7 processor without the mmu. This behaviour
is now same as in the mmu case.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is what is done for the regular interrupts in kernel/irqs/proc.c
already, before calling arch_show_interrupts(). Not doing so for the
IPIs causes the column headers not to match with the content whenever
some CPUs are offline.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Previously, the ASoC 'platform' (PCM/DMA) object was instantiated via a
platform_device. This didn't represent the hardware well, since there
was no separate hardware associated with this platform_device; it was a
virtual device with sole purpose to call snd_soc_register_platform().
This change removes the platform_device completely. Each Samsung DAI now
registers the ASoC 'platform' itself. Machine drivers are adjusted for
the new 'platform' name.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
6e20a0a429
(gpio: pcf857x: enable gpio_to_irq() support)
added gpio_to_irq() support on pcf857x driver,
but it used pdata->irq.
This patch modifies driver to use client->irq instead of it.
It modifies kzm9g board platform settings,
and device probe information too.
This patch is tested on kzm9g board
Reported-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the MPC5200B based a3m071 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
* pci/mjg-pci-roms-from-efi:
x86: Use PCI setup data
PCI: Add support for non-BAR ROMs
PCI: Add pcibios_add_device
EFI: Stash ROMs if they're not in the PCI BAR
HSMMC IP on AM33xx need a special setting to handle High-speed cards.
Other platforms like TI81xx, OMAP4 may need this as-well. This depends
on the HSMMC IP timing closure done for the high speed cards.
From AM335x TRM (SPRUH73F - 18.3.12 Output Signals Generation):
The MMC/SD/SDIO output signals can be driven on either falling edge or
rising edge depending on the SD_HCTL[2] HSPE bit. This feature allows
to reach better timing performance, and thus to increase data transfer
frequency.
There are few pre-requisites for enabling the HSPE bit
- Controller should support High-Speed-Enable Bit and
- Controller should not be using DDR Mode and
- Controller should advertise that it supports High Speed in
capabilities register and
- MMC/SD clock coming out of controller > 25MHz
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The at91-mci driver is not needed anymore since the atmel-mci driver now
supports all Atmel devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Pull MIPS fixes from Ralf Baechle:
"These are the fixes for the N32 syscall bugs found by Al, an
extraneous break that broke detection for R3000 and R3081 processors,
an endless loop processing signals for kernel task (x86 received the
same fix a while ago) and a fix for transparent huge page which took
ages to track down because it was so hard to come up with a workable
test case."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix endless loop when processing signals for kernel tasks
MIPS: R3000/R3081: Fix CPU detection.
MIPS: N32: Fix signalfd4 syscall entry point
MIPS: N32: Fix preadv(2) and pwritev(2) entry points.
MIPS: Avoid mcheck by flushing page range in huge_ptep_set_access_flags()
The vmclear function will be assigned to the callback function pointer
when loading kvm-intel module. And the bitmap indicates whether we
should do VMCLEAR operation in kdump. The bits in the bitmap are
set/unset according to different conditions.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
This patch provides a way to VMCLEAR VMCSs related to guests
on all cpus before executing the VMXOFF when doing kdump. This
is used to ensure the VMCSs in the vmcore updated and
non-corrupted.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
I've legally changed my name with New York State, the US Social Security
Administration, et al. This patch propagates the name change and change
in initials and login to comments in the kernel source as well.
Signed-off-by: Nadia Yvette Chambers <nyc@holomorphy.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CAST5 and CAST6 both use same lookup tables, which can be moved shared module
'cast_common'.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are two cases we need to adjust page size in set_spte:
1): the one is other vcpu creates new sp in the window between mapping_level()
and acquiring mmu-lock.
2): the another case is the new sp is created by itself (page-fault path) when
guest uses the target gfn as its page table.
In current code, set_spte drop the spte and emulate the access for these case,
it works not good:
- for the case 1, it may destroy the mapping established by other vcpu, and
do expensive instruction emulation.
- for the case 2, it may emulate the access even if the guest is accessing
the page which not used as page table. There is a example, 0~2M is used as
huge page in guest, in this huge page, only page 3 used as page table, then
guest read/writes on other pages can cause instruction emulation.
Both of these cases can be fixed by allowing guest to retry the access, it
will refault, then we can establish the mapping by using small page
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Since GCC 4.4, there have been __builtin_bswap32() and __builtin_bswap16()
intrinsics. A __builtin_bswap16() came a little later (4.6 for PowerPC,
48 for other platforms).
By using these instead of the inline assembler that most architectures
have in their __arch_swabXX() macros, we let the compiler see what's
actually happening. The resulting code should be at least as good, and
much *better* in the cases where it can be combined with a nearby load
or store, using a load-and-byteswap or store-and-byteswap instruction
(e.g. lwbrx/stwbrx on PowerPC, movbe on Atom).
When GCC is sufficiently recent *and* the architecture opts in to using
the intrinsics by setting CONFIG_ARCH_USE_BUILTIN_BSWAP, they will be
used in preference to the __arch_swabXX() macros. An architecture which
does not set ARCH_USE_BUILTIN_BSWAP will continue to use its own
hand-crafted macros.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Implement ONE_REG interface for EPCR register adding KVM_REG_PPC_EPCR to
the list of ONE_REG PPC supported registers.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: remove HV dependency, use get/put_user]
Signed-off-by: Alexander Graf <agraf@suse.de>
Add EPCR support in booke mtspr/mfspr emulation. EPCR register is defined only
for 64-bit and HV categories, we will expose it at this point only to 64-bit
virtual processors running on 64-bit HV hosts.
Define a reusable setter function for vcpu's EPCR.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: move HV dependency in the code]
Signed-off-by: Alexander Graf <agraf@suse.de>
When delivering guest IRQs, update MSR computation mode according to guest
interrupt computation mode found in EPCR.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: remove HV dependency in the code]
Signed-off-by: Alexander Graf <agraf@suse.de>
In BookE, EPCR is defined and valid when either the HV or the 64bit
category are implemented. Reflect this in the field definition.
Today the only KVM target on 64bit is HV enabled, so there is no
change in actual source code, but this keeps the code closer to the
spec and doesn't build up artificial road blocks for a PR KVM
on 64bit.
Signed-off-by: Alexander Graf <agraf@suse.de>
Extend MAS2 EPN mask to retain most significant bits on 64-bit hosts.
Use this mask in tlb effective address accessor.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Mask high 32 bits of MAS2's effective page number in tlbwe emulation for guests
running in 32-bit mode.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Mask high 32 bits of effective address in emulation layer for guests running
in 32-bit mode.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: fix indent]
Signed-off-by: Alexander Graf <agraf@suse.de>
Add emulation helper for getting instruction ea and refactor tlb instruction
emulation to use it.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: keep rt variable around]
Signed-off-by: Alexander Graf <agraf@suse.de>
Add interrupt handling support for 64-bit bookehv hosts. Unify 32 and 64 bit
implementations using a common stack layout and a common execution flow starting
from kvm_handler_common macro. Update documentation for 64-bit input register
values. This patch only address the bolted TLB miss exception handlers version.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
GET_VCPU define will not be implemented for 64-bit for performance reasons
so get rid of it also on 32-bit.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
64-bit GCC 4.5.1 warns about an uninitialized variable which was guarded
by a flag. Initialize the variable to make it happy.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: reword comment]
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently, if a machine check interrupt happens while we are in the
guest, we exit the guest and call the host's machine check handler,
which tends to cause the host to panic. Some machine checks can be
triggered by the guest; for example, if the guest creates two entries
in the SLB that map the same effective address, and then accesses that
effective address, the CPU will take a machine check interrupt.
To handle this better, when a machine check happens inside the guest,
we call a new function, kvmppc_realmode_machine_check(), while still in
real mode before exiting the guest. On POWER7, it handles the cases
that the guest can trigger, either by flushing and reloading the SLB,
or by flushing the TLB, and then it delivers the machine check interrupt
directly to the guest without going back to the host. On POWER7, the
OPAL firmware patches the machine check interrupt vector so that it
gets control first, and it leaves behind its analysis of the situation
in a structure pointed to by the opal_mc_evt field of the paca. The
kvmppc_realmode_machine_check() function looks at this, and if OPAL
reports that there was no error, or that it has handled the error, we
also go straight back to the guest with a machine check. We have to
deliver a machine check to the guest since the machine check interrupt
might have trashed valid values in SRR0/1.
If the machine check is one we can't handle in real mode, and one that
OPAL hasn't already handled, or on PPC970, we exit the guest and call
the host's machine check handler. We do this by jumping to the
machine_check_fwnmi label, rather than absolute address 0x200, because
we don't want to re-execute OPAL's handler on POWER7. On PPC970, the
two are equivalent because address 0x200 just contains a branch.
Then, if the host machine check handler decides that the system can
continue executing, kvmppc_handle_exit() delivers a machine check
interrupt to the guest -- once again to let the guest know that SRR0/1
have been modified.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix checkpatch warnings]
Signed-off-by: Alexander Graf <agraf@suse.de>
When we change or remove a HPT (hashed page table) entry, we can do
either a global TLB invalidation (tlbie) that works across the whole
machine, or a local invalidation (tlbiel) that only affects this core.
Currently we do local invalidations if the VM has only one vcpu or if
the guest requests it with the H_LOCAL flag, though the guest Linux
kernel currently doesn't ever use H_LOCAL. Then, to cope with the
possibility that vcpus moving around to different physical cores might
expose stale TLB entries, there is some code in kvmppc_hv_entry to
flush the whole TLB of entries for this VM if either this vcpu is now
running on a different physical core from where it last ran, or if this
physical core last ran a different vcpu.
There are a number of problems on POWER7 with this as it stands:
- The TLB invalidation is done per thread, whereas it only needs to be
done per core, since the TLB is shared between the threads.
- With the possibility of the host paging out guest pages, the use of
H_LOCAL by an SMP guest is dangerous since the guest could possibly
retain and use a stale TLB entry pointing to a page that had been
removed from the guest.
- The TLB invalidations that we do when a vcpu moves from one physical
core to another are unnecessary in the case of an SMP guest that isn't
using H_LOCAL.
- The optimization of using local invalidations rather than global should
apply to guests with one virtual core, not just one vcpu.
(None of this applies on PPC970, since there we always have to
invalidate the whole TLB when entering and leaving the guest, and we
can't support paging out guest memory.)
To fix these problems and simplify the code, we now maintain a simple
cpumask of which cpus need to flush the TLB on entry to the guest.
(This is indexed by cpu, though we only ever use the bits for thread
0 of each core.) Whenever we do a local TLB invalidation, we set the
bits for every cpu except the bit for thread 0 of the core that we're
currently running on. Whenever we enter a guest, we test and clear the
bit for our core, and flush the TLB if it was set.
On initial startup of the VM, and when resetting the HPT, we set all the
bits in the need_tlb_flush cpumask, since any core could potentially have
stale TLB entries from the previous VM to use the same LPID, or the
previous contents of the HPT.
Then, we maintain a count of the number of online virtual cores, and use
that when deciding whether to use a local invalidation rather than the
number of online vcpus. The code to make that decision is extracted out
into a new function, global_invalidates(). For multi-core guests on
POWER7 (i.e. when we are using mmu notifiers), we now never do local
invalidations regardless of the H_LOCAL flag.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The mask of MSR bits that get transferred from the guest MSR to the
shadow MSR included MSR_DE. In fact that bit only exists on Book 3E
processors, and it is assigned the same bit used for MSR_BE on Book 3S
processors. Since we already had MSR_BE in the mask, this just removes
MSR_DE.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes various issues in how we were handling the VSX registers
that exist on POWER7 machines. First, we were running off the end
of the current->thread.fpr[] array. Ultimately this was because the
vcpu->arch.vsr[] array is sized to be able to store both the FP
registers and the extra VSX registers (i.e. 64 entries), but PR KVM
only uses it for the extra VSX registers (i.e. 32 entries).
Secondly, calling load_up_vsx() from C code is a really bad idea,
because it jumps to fast_exception_return at the end, rather than
returning with a blr instruction. This was causing it to jump off
to a random location with random register contents, since it was using
the largely uninitialized stack frame created by kvmppc_load_up_vsx.
In fact, it isn't necessary to call either __giveup_vsx or load_up_vsx,
since giveup_fpu and load_up_fpu handle the extra VSX registers as well
as the standard FP registers on machines with VSX. Also, since VSX
instructions can access the VMX registers and the FP registers as well
as the extra VSX registers, we have to load up the FP and VMX registers
before we can turn on the MSR_VSX bit for the guest. Conversely, if
we save away any of the VSX or FP registers, we have to turn off MSR_VSX
for the guest.
To handle all this, it is more convenient for a single call to
kvmppc_giveup_ext() to handle all the state saving that needs to be done,
so we make it take a set of MSR bits rather than just one, and the switch
statement becomes a series of if statements. Similarly kvmppc_handle_ext
needs to be able to load up more than one set of registers.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds basic emulation of the PURR and SPURR registers. We assume
we are emulating a single-threaded core, so these advance at the same
rate as the timebase. A Linux kernel running on a POWER7 expects to
be able to access these registers and is not prepared to handle a
program interrupt on accessing them.
This also adds a very minimal emulation of the DSCR (data stream
control register). Writes are ignored and reads return zero.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently, if the guest does an H_PROTECT hcall requesting that the
permissions on a HPT entry be changed to allow writing, we make the
requested change even if the page is marked read-only in the host
Linux page tables. This is a problem since it would for instance
allow a guest to modify a page that KSM has decided can be shared
between multiple guests.
To fix this, if the new permissions for the page allow writing, we need
to look up the memslot for the page, work out the host virtual address,
and look up the Linux page tables to get the PTE for the page. If that
PTE is read-only, we reduce the HPTE permissions to read-only.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes a bug in the code which allows userspace to read out the
contents of the guest's hashed page table (HPT). On the second and
subsequent passes through the HPT, when we are reporting only those
entries that have changed, we were incorrectly initializing the index
field of the header with the index of the first entry we skipped
rather than the first changed entry. This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
With HV-style KVM, we maintain reverse-mapping lists that enable us to
find all the HPT (hashed page table) entries that reference each guest
physical page, with the heads of the lists in the memslot->arch.rmap
arrays. When we reset the HPT (i.e. when we reboot the VM), we clear
out all the HPT entries but we were not clearing out the reverse
mapping lists. The result is that as we create new HPT entries, the
lists get corrupted, which can easily lead to loops, resulting in the
host kernel hanging when it tries to traverse those lists.
This fixes the problem by zeroing out all the reverse mapping lists
when we zero out the HPT. This incidentally means that we are also
zeroing our record of the referenced and changed bits (not the bits
in the Linux PTEs, used by the Linux MM subsystem, but the bits used
by the KVM_GET_DIRTY_LOG ioctl, and those used by kvm_age_hva() and
kvm_test_age_hva()).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
A new ioctl, KVM_PPC_GET_HTAB_FD, returns a file descriptor. Reads on
this fd return the contents of the HPT (hashed page table), writes
create and/or remove entries in the HPT. There is a new capability,
KVM_CAP_PPC_HTAB_FD, to indicate the presence of the ioctl. The ioctl
takes an argument structure with the index of the first HPT entry to
read out and a set of flags. The flags indicate whether the user is
intending to read or write the HPT, and whether to return all entries
or only the "bolted" entries (those with the bolted bit, 0x10, set in
the first doubleword).
This is intended for use in implementing qemu's savevm/loadvm and for
live migration. Therefore, on reads, the first pass returns information
about all HPTEs (or all bolted HPTEs). When the first pass reaches the
end of the HPT, it returns from the read. Subsequent reads only return
information about HPTEs that have changed since they were last read.
A read that finds no changed HPTEs in the HPT following where the last
read finished will return 0 bytes.
The format of the data provides a simple run-length compression of the
invalid entries. Each block of data starts with a header that indicates
the index (position in the HPT, which is just an array), the number of
valid entries starting at that index (may be zero), and the number of
invalid entries following those valid entries. The valid entries, 16
bytes each, follow the header. The invalid entries are not explicitly
represented.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix documentation]
Signed-off-by: Alexander Graf <agraf@suse.de>
This makes a HPTE removal function, kvmppc_do_h_remove(), available
outside book3s_hv_rm_mmu.c. This will be used by the HPT writing
code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This uses a bit in our record of the guest view of the HPTE to record
when the HPTE gets modified. We use a reserved bit for this, and ensure
that this bit is always cleared in HPTE values returned to the guest.
The recording of modified HPTEs is only done if other code indicates
its interest by setting kvm->arch.hpte_mod_interest to a non-zero value.
The reason for this is that when later commits add facilities for
userspace to read the HPT, the first pass of reading the HPT will be
quicker if there are no (or very few) HPTEs marked as modified,
rather than having most HPTEs marked as modified.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes a bug where adding a new guest HPT entry via the H_ENTER
hcall would lose the "changed" bit in the reverse map information
for the guest physical page being mapped. The result was that the
KVM_GET_DIRTY_LOG could return a zero bit for the page even though
the page had been modified by the guest.
This fixes it by only modifying the index and present bits in the
reverse map entry, thus preserving the reference and change bits.
We were also unnecessarily setting the reference bit, and this
fixes that too.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This restructures the code that creates HPT (hashed page table)
entries so that it can be called in situations where we don't have a
struct vcpu pointer, only a struct kvm pointer. It also fixes a bug
where kvmppc_map_vrma() would corrupt the guest R4 value.
Most of the work of kvmppc_virtmode_h_enter is now done by a new
function, kvmppc_virtmode_do_h_enter, which itself calls another new
function, kvmppc_do_h_enter, which contains most of the old
kvmppc_h_enter. The new kvmppc_do_h_enter takes explicit arguments
for the place to return the HPTE index, the Linux page tables to use,
and whether it is being called in real mode, thus removing the need
for it to have the vcpu as an argument.
Currently kvmppc_map_vrma creates the VRMA (virtual real mode area)
HPTEs by calling kvmppc_virtmode_h_enter, which is designed primarily
to handle H_ENTER hcalls from the guest that need to pin a page of
memory. Since H_ENTER returns the index of the created HPTE in R4,
kvmppc_virtmode_h_enter updates the guest R4, corrupting the guest R4
in the case when it gets called from kvmppc_map_vrma on the first
VCPU_RUN ioctl. With this, kvmppc_map_vrma instead calls
kvmppc_virtmode_do_h_enter with the address of a dummy word as the
place to store the HPTE index, thus avoiding corrupting the guest R4.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In order to support the generic eventfd infrastructure on PPC, we need
to call into the generic KVM in-kernel device mmio code.
Signed-off-by: Alexander Graf <agraf@suse.de>
EFI can provide PCI ROMs out of band via boot services, which may not be
available after boot. Add support for using the data handed off to us by
the boot stub or bootloader.
[bhelgaas: added Seth's boot_params section mismatch fix]
[bhelgaas: drop "boot_params.hdr.version < 0x0209" test]
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
EFI provides support for providing PCI ROMs via means other than the ROM
BAR. This support vanishes after we've exited boot services, so add support
for stashing copies of the ROMs in setup_data if they're not otherwise
available.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
The problem occurs [1] when a kernel-mode task returns from a system
call with a pending signal.
A real-life scenario is a child of 'khelper' returning from a failed
kernel_execve() in ____call_usermodehelper() [ kernel/kmod.c ].
kernel_execve() fails due to a pending SIGKILL, which is the result of
"kill -9 -1" (at least, busybox's init does it upon reboot).
The loop is as follows:
* syscall_exit_work:
- work_pending: // start_of_the_loop
- work_notifysig:
- do_notify_resume()
- do_signal()
- if (!user_mode(regs)) return;
- resume_userspace // TIF_SIGPENDING is still set
- work_pending // so we call work_pending => goto
// start_of_the_loop
More information can be found in another LKML thread:
http://www.serverphorums.com/read.php?12,457826
[1] The problem was also reproduced on !CONFIG_VM86 x86, and the
following fix was accepted.
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=29a2e2836ff9ea65a603c89df217f4198973a74f
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3571/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Broken since e05ea74fc56f347f872ef9946d27c53e8bf20864 (lmo) rsp.
cea7e2dfde (kernel.org) [MIPS: Sort out CPU
type to name translation.] These CPUs are no longer very popular to say
the least ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Murphy McCauley <murphy.mccauley@gmail.com>
This needs to use the compat entry point or it's going to fail on big
endian systems.
Noticed by Al Viro.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The DMA API allows to avoid DMA unmaps because they are NOPs on some
plattforms. But not on s390, so force them.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
VMX behaves now as SVM wrt to FPU initialization. Code has been moved to
generic code path. General-purpose registers are now cleared on reset and
INIT. SVM code properly initializes EDX.
Signed-off-by: Julian Stecklina <jsteckli@os.inf.tu-dresden.de>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Bit24 in VMX_EPT_VPID_CAP_MASI is not used for address-specific invalidation capability
reporting, so remove it from KVM to avoid conflicts in future.
Signed-off-by: Zhang Xiantao <xiantao.zhang@intel.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Bit 6 in EPT vmexit's exit qualification is not defined in SDM, so remove it.
Signed-off-by: Zhang Xiantao <xiantao.zhang@intel.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
The PCI instructions may be used in IRQ context so scheduling is forbidden.
Use udelay and shorten the delay since we are now polling.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
struct timex is different on arm and arm64; adjtimex(2) takes care to
convert, clock_adjtime(2) doesn't...
Signed-off-by: Al Viro <viro@ZenIV.linux.org.uk>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
In order to be able to reuse the save-restore code in KVM, move
it to a pair of macros, similar to what the 32bit code does.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The architecture doesn't mandate any reset value for vttbr_el2.
Better set it to a known value before some HYP code gets confused.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
If booted in EL2, install an dummy hypervisor whose only purpose
is to be replaced by a full fledged one.
A minimal API allows to:
- obtain the current HYP vectors (__hyp_get_vectors)
- set new HYP vectors (__hyp_set_vectors)
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
To be able to signal the availability of EL2 to other parts of
the kernel, record the boot mode.
Once booted, two predicates indicate if HYP mode is available,
and if not, whether this is due to a boot mode mismatch or not.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This macro is also useful to other bits defining vectors (hypervisor
stub, KVM...).
Move it to a common location.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The general purpose registers in AArch32 are mapped in an
architecturally defined manner into the AArch64 registers.
It allows the AArch32 registers of an application or a virtual
machine to be inspected by the OS or an hypervisor.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We want to use the virtual counter at EL0, as the physical counter
may not track the current clocksource for guests running under a
hypervisor.
This patch updates the vdso and generic timer driver to use the virtual
counter. The kernel EL2 entry code is also updated to ensure that the
virtual offset is initialised to zero.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Shifting the nanosecond component of the computed timespec early can
lead to sub-ns inaccuracies when using the truncated value as input to
further arithmetic for things like conversions to monotonic time.
This patch defers the timespec shifting until after the final value has
been computed.
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In preparation for sub-ns precision in the vdso timespec maths, change
the __do_get_tspec register allocation so that we return the clocksource
shift value instead of the unused xtime tspec.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When returning coarse realtime values from clock_gettime, we must still
check the sequence counter to ensure that the kernel does not update
the vdso datapage whilst we are loading the coarse timespec as this
could potentially result in time appearing to go backwards.
This patch delays the coarse realtime check until after we have loaded
successfully from the vdso datapage. This does mean that we always load
the wtm timespec, but conditionalising the load and adding an extra
sequence test is unlikely to buy us anything other than messy code,
particularly as the sequence test implies a read barrier.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The generic timer clocksource has 56 bits of precision and as such must
be masked appropriately after we have read it. The current mask
generated by a movn instruction is off by 4 bits, so we accidentally
include the top 4 bits in the final value.
This patch fixes the broken mask.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The existing clk.c code for ColdFire CPUs has one set of functions to
support those CPU types that have selectable clocks (those with a PPMCR
register), and a duplicate simpler set for those with static clocks.
Modify the clk.c code so there is just one set of support functions. All
CPU types now define a list of clocks (in "struct clk"s), so we only need
a single set of clock functions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The clock support code for ColdFire CPUs currently supports those that
have the clock control register PPMCR. Expose the struct clk for all CPU
types and add a definition for all other ColdFire CPU types.
With this we will be able to define simple clock trees for all ColdFire
CPU types, even though they will not be able to be enabled or disabled.
They will be able to report the clock rate.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
When compiling for original 68000 or ColdFire targets you will get the
following warning when compiling arch/m68k/lib/memcpy.c:
CC arch/m68k/lib/memcpy.o
arch/m68k/lib/memcpy.c: In function ‘__builtin_memcpy’:
arch/m68k/lib/memcpy.c:13:15: warning: unused variable ‘temp1’
This is easily fixed by moving the definition of temp1 into the code block
where it is used.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The page_to_virt() macro for m68knommu is currently effectively returning
an int type. But the equivilent m68k macro returns a void * virtual address.
Modify the non-MMU macro to return a void * as well (using the __va macro).
This change will remove compiler warnings in common m68k code that use this
macro.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The ColdFire 5249 and 525x family of SoCs are very similar. Most of the
internals are the same, and are mapped the same. We can use a single set of
peripheral definitions for all of them.
So merge the current m5249sim.h and m525xsim.h definitions into a single
file. The 5249 is now obsolete, and the 525x parts are current, so I have
chosen to move everything into the existing m525xsim.h file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
As pointed out by Geert, MC68000 target needs to be disabled when
MMU support is enabled.
From Geert:
This needs a "depends on !MMU".
Else allmodconfig will select it, causing -m68000 to be passed to the assembler,
which may break the build depending on your version of binutils, a.o.
arch/m68k/kernel/entry.S:186: Error: invalid instruction for this
architecture; needs 68020 or higher (68020 [68k, 68ec020], 68030
[68ec030], 68040 [68ec040], 68060 [68ec060]) -- statement `bfextu
%sp@(50){#0,#4},%d0' ignored
arch/m68k/kernel/entry.S:211: Error: invalid operand mode for this
architecture; needs 68020 or higher -- statement `jbsr
@(sys_call_table,%d0:l:4)@(0)' ignored
Cfr. http://kisskb.ellerman.id.au/kisskb/buildresult/7416877/
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Allow the M68000 option to be user configurable, for systems based on
the original stand alone 68000 CPU.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
This patch merges all 68000 core cpus into one directory.
There is a lot of common code in the 68328, 68EZ328 and 68VZ328 directories.
This will also facilitate easy development of support for original stand
alone MC68000 CPU machines.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
By using the native syscall entry point the kernel was also expecting
64-bit iovec structures.
This is broken since ddd9e91b71 [preadv/
pwritev: MIPS: Add preadv(2) and pwritev(2) syscalls.] which originally
added these two syscalls. I walked through piles of code, including
libc and couldn't find anything that would have worked around the issue
so this change the API to what it should always have been.
Noticed and patch suggested by Al Viro.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull sparc fixes from David Miller:
"Two small fixes for Sparc, nobody uses sparc, so these are low risk :-)
1) Piggyback is too picky about the symbol types that _start and _end
have in the final kernel image, and it thus breaks with newer
binutils. Future proof by getting rid of the symbol type checks.
2) exit_group() should kill register windows on sparc64 the same way
we do for plain exit(). Thanks to Al Viro for spotting this."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Fix piggyback with newer binutils.
sparc64: exit_group should kill register windows just like plain exit.
Problem:
1) Huge page mapping of anonymous memory is initially invalid. Will be
faulted in by copy-on-write mechanism.
2) Userspace attempts store at the end of the huge mapping.
3) TLB Refill exception handler fill TLB with a normal (4K sized)
invalid page at the end of the huge mapping virtual address range.
4) Userspace restarted, and re-attempts the store at the end of the
huge mapping.
5) Page from #3 is invalid, we get a fault and go to the hugepage
fault handler. This tries to map a huge page and calls
huge_ptep_set_access_flags() to install the mapping.
6) We just call the generic ptep_set_access_flags() to set up the page
tables, but the flush there assumes a normal (4K sized) page and
only tries to flush the first part of the huge page virtual address
out of the TLB, since the existing entry from step #3 doesn't
conflict, nothing is flushed.
7) We attempt to load the mapping into the TLB, but because it
conflicts with the entry from step #3, we get a Machine Check
exception.
The fix: Flush the entire rage covered by the huge page in
huge_ptep_set_access_flags(), and remove the optimization in
local_flush_tlb_range() so that the flush actually does the correct
thing.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Hillf Danton <dhillf@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/4661/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit dd617f258cc39d36be26afee9912624a2d23112c)
The current rules have the .dtb files build in a different directory
from the .dts files. This patch changes microblaze to use the generic dtb
rule which builds .dtb files in the same directory as the source .dts.
This requires moving parts of arch/microblaze/boot/Makefile into newly
created arch/microblaze/boot/dts/Makefile, and updating
arch/microblaze/Makefile to call the new Makefile. linked_dtb.S is also
moved into boot/dts/ since it's used by rules that were moved.
Cc: Michal Simek <monstr@monstr.eu>
Cc: microblaze-uclinux@itee.uq.edu.au
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The current rules have the .dtb files build in a different directory
from the .dts files. This patch changes c6x to use the generic dtb
rule which builds .dtb files in the same directory as the source .dts.
This requires moving parts of arch/c6x/boot/Makefile into newly created
arch/c6x/boot/dts/Makefile, and updating arch/c6x/Makefile to call the
new Makefile. linked_dtb.S is also moved into boot/dts/ since it's used
by rules that were moved.
Acked-by: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: linux-c6x-dev@linux-c6x.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The current rules have the .dtb files build in a different directory
from the .dts files. This patch changes openrisc to use the generic dtb
rule which builds .dtb files in the same directory as the source .dts.
This requires renaming arch/openrisc/boot/Makefile to
arch/openrisc/boot/dts/Makefile, and updating arch/openrisc/Makefile to
call the new Makefile.
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Based on Rob Herring's patches for arch/arm, this patch adds a dtbs
target to arch/arm64/boot/Makefile.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
If the DIU framebuffer driver is not enabled, then there's no point in
compiling any platform DIU code, because it will never be used. Most of
the platform code was protected in the appropriate #ifdef, but not all.
This caused a break in some randconfig builds.
This is only a problem on the 512x platforms. The P1022DS and MPC8610HPCD
platforms are already correct.
This patch reverts commit 12e36309f8 ("powerpc:
Option FB_FSL_DIU is not really optional for mpc512x") and restores the
ability to configure DIU support.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Newer versions of binutils mark '_end' as 'B' instead of 'A' for
whatever reason.
To be honest, the piggyback code doesn't actually care what kind
of symbol _start and _end are, it just wants to find them and
record the address.
So remove the type from the match strings.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 9d73fc2d64 ("open*(2) compat fixes (s390, arm64)") I said:
>
> The usual rules for open()/openat()/open_by_handle_at() are
> 1) native 32bit - don't force O_LARGEFILE in flags
> 2) native 64bit - force O_LARGEFILE in flags
> 3) compat on 64bit host - as for native 32bit
> 4) native 32bit ABI for 64bit system (mips/n32, x86/x32) - as for native 64bit
>
> There are only two exceptions - s390 compat has open() forcing O_LARGEFILE and
> arm64 compat has open_by_handle_at() doing the same thing. The same binaries
> on native host (s390/31 and arm resp.) will *not* force O_LARGEFILE, so IMO
> both are emulation bugs.
Three exceptions, actually - parisc open() is another case like that.
Native 32bit won't force O_LARGEFILE, the same binary on parisc64 will.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current rules have the .dtb files build in a different directory
from the .dts files. This patch changes arm64 to use the generic dtb
rule which builds .dtb files in the same directory as the source .dts.
This requires moving parts of arch/arm64/boot/Makefile into newly created
arch/arm64/boot/dts/Makefile, and updating arch/arm64/Makefile to call the
new Makefile.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The current rules have the .dtb files build in a different directory
from the .dts files. The only reason for this is that it was what
PowerPC has done historically. This patch changes ARM to use the generic
dtb rule which builds .dtb files in the same directory as the source .dts.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[swarren: added rm command for old stale .dtb files]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Without the patch, kind of below warning will be dumped if DMA-API
debug is enabled:
[ 11.069763] ------------[ cut here ]------------
[ 11.074645] WARNING: at lib/dma-debug.c:948 check_unmap+0x770/0x860()
[ 11.081420] ehci-omap ehci-omap.0: DMA-API: device driver failed to
check map error[device address=0x0000000
0adb78e80] [size=8 bytes] [mapped as single]
[ 11.095611] Modules linked in:
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This prevents hwmod _enable_clocks...omap2_dflt_clk_enable path
from enabling modulemode inside CLKCTRL using its clk->enable_reg
field. Instead is left to _omap4_enable_module though soc_ops, as
the one in charge of this setting.
According to comments received[1] for related patches the idea is
to get rid of leaf clocks in future. So remove these two while at it.
[1] http://lkml.org/lkml/2012/8/20/226
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Use runtime PM functionality interfaced with hwmod enable/idle
functions, to replace direct clock operations and sysconfig
handling.
Due to reset sequence, pm_runtime_[get|put]_sync must be used, to
avoid possible operations with the module under reset. Because of
this and given that the driver uses spin_locks to protect their
critical sections, we must use pm_runtime_irq_safe in order for the
runtime ops to be happy, otherwise might_sleep_if checks in runtime
framework will complain.
The remaining pm_runtime out of iommu_enable and iommu_disable
corresponds to paths that can be accessed through debugfs, some of
them doesn't work if the module is not enabled first, but in future
if the mmu is idled withouth freeing, these are needed to debug.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Use hwmod data and device attributes to build and register an
omap device for iommu driver.
- Update the naming convention in isp module.
- Remove unneeded check for number of resources, as this is now
handled by omap_device and prevents driver from loading.
- Now unused, remove platform device and resource data, handling
of sysconfig register for softreset purposes, use default
latency structure.
- Use hwmod API for reset handling.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The dereference to 'zdev' should be moved below the NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Using kmem_cache_zalloc() instead of kmem_cache_alloc() and memset().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for XOR instruction for use with X/K.
s390 JIT support for the new BPF_S_ALU_XOR_* instructions introduced
with 9e49e889 "filter: add XOR instruction for use with X/K".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for MOD operation for s390's JIT.
Same as 280050cc "x86 bpf_jit: support MOD operation" for x86 which
adds JIT support for the generic new MOD operation introduced with
b6069a9570 "filter: add MOD operation".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the previously unused TPIDRPRW register to store percpu offsets.
TPIDRPRW is only accessible in PL1, so it can only be used in the kernel.
This replaces 2 loads with a mrc instruction for each percpu variable
access. With hackbench, the performance improvement is 1.4% on Cortex-A9
(highbank). Taking an average of 30 runs of "hackbench -l 1000" yields:
Before: 6.2191
After: 6.1348
Will Deacon reported similar delta on v6 with 11MPCore.
The asm "memory clobber" are needed here to ensure the percpu offset
gets reloaded. Testing by Will found that this would not happen in
__schedule() which is a bit of a special case as preemption is disabled
but the execution can move cores.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This passes the lm resource to register the AMBA devices on the
LM as contained within the LM resource.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Conflicts:
arch/x86/kernel/ptrace.c
Pull the latest RCU tree from Paul E. McKenney:
" The major features of this series are:
1. A first version of no-callbacks CPUs. This version prohibits
offlining CPU 0, but only when enabled via CONFIG_RCU_NOCB_CPU=y.
Relaxing this constraint is in progress, but not yet ready
for prime time. These commits were posted to LKML at
https://lkml.org/lkml/2012/10/30/724, and are at branch rcu/nocb.
2. Changes to SRCU that allows statically initialized srcu_struct
structures. These commits were posted to LKML at
https://lkml.org/lkml/2012/10/30/296, and are at branch rcu/srcu.
3. Restructuring of RCU's debugfs output. These commits were posted
to LKML at https://lkml.org/lkml/2012/10/30/341, and are at
branch rcu/tracing.
4. Additional CPU-hotplug/RCU improvements, posted to LKML at
https://lkml.org/lkml/2012/10/30/327, and are at branch rcu/hotplug.
Note that the commit eliminating __stop_machine() was judged to
be too-high of risk, so is deferred to 3.9.
5. Changes to RCU's idle interface, most notably a new module
parameter that redirects normal grace-period operations to
their expedited equivalents. These were posted to LKML at
https://lkml.org/lkml/2012/10/30/739, and are at branch rcu/idle.
6. Additional diagnostics for RCU's CPU stall warning facility,
posted to LKML at https://lkml.org/lkml/2012/10/30/315, and
are at branch rcu/stall. The most notable change reduces the
default RCU CPU stall-warning time from 60 seconds to 21 seconds,
so that it once again happens sooner than the softlockup timeout.
7. Documentation updates, which were posted to LKML at
https://lkml.org/lkml/2012/10/30/280, and are at branch rcu/doc.
A couple of late-breaking changes were posted at
https://lkml.org/lkml/2012/11/16/634 and
https://lkml.org/lkml/2012/11/16/547.
8. Miscellaneous fixes, which were posted to LKML at
https://lkml.org/lkml/2012/10/30/309, along with a late-breaking
change posted at Fri, 16 Nov 2012 11:26:25 -0800 with message-ID
<20121116192625.GA447@linux.vnet.ibm.com>, but which lkml.org
seems to have missed. These are at branch rcu/fixes.
9. Finally, a fix for an lockdep-RCU splat was posted to LKML
at https://lkml.org/lkml/2012/11/7/486. This is at rcu/next. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The usual rules for open()/openat()/open_by_handle_at() are
1) native 32bit - don't force O_LARGEFILE in flags
2) native 64bit - force O_LARGEFILE in flags
3) compat on 64bit host - as for native 32bit
4) native 32bit ABI for 64bit system (mips/n32, x86/x32) - as for
native 64bit
There are only two exceptions - s390 compat has open() forcing
O_LARGEFILE and arm64 compat has open_by_handle_at() doing the same
thing. The same binaries on native host (s390/31 and arm resp.) will
*not* force O_LARGEFILE, so IMO both are emulation bugs.
Objections? The fix is obvious...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes PINCTRL related config options visible.
Otherwise there is no way to build pinctrl drivers for MMP2, PXA168 and PXA910.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull RCU fix from Ingo Molnar:
"Fix leaking RCU extended quiescent state, which might trigger warnings
and mess up the extended quiescent state tracking logic into thinking
that we are in "RCU user mode" while we aren't."
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Fix unrecovered RCU user mode in syscall_trace_leave()
Pull perf fixes from Ingo Molnar:
"This is mostly about unbreaking architectures that took the UAPI
changes in the v3.7 cycle, plus misc fixes."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf kvm: Fix building perf kvm on non x86 arches
perf kvm: Rename perf_kvm to perf_kvm_stat
perf: Make perf build for x86 with UAPI disintegration applied
perf powerpc: Use uapi/unistd.h to fix build error
tools: Pass the target in descend
tools: Honour the O= flag when tool build called from a higher Makefile
tools: Define a Makefile function to do subdir processing
x86: Export asm/{svm.h,vmx.h,perf_regs.h}
perf tools: Fix strbuf_addf() when the buffer needs to grow
perf header: Fix numa topology printing
perf, powerpc: Fix hw breakpoints returning -ENOSPC
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=w+UN
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm2
From Tony Lindgren:
Remaining patches to allow omap2+ to build with multiplatform
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
* tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
Conflicts due to surrounding changes in:
arch/arm/mach-omap2/omap_hwmod_2420_data.c
arch/arm/mach-omap2/omap_hwmod_2430_data.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yFcc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/headers
From Tony Lindgren:
Move most of remaining omap iommu code to drivers/iommu.
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
* tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
Conflicts due to surrounding changes in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
drivers/media/platform/omap3isp/ispvideo.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yFcc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Move most of remaining omap iommu code to drivers/iommu.
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
* tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
Conflicts due to surrounding changes fixed up in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
drivers/media/platform/omap3isp/ispvideo.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull x86 fixes from Peter Anvin.
This includes the resume-time FPU corruption fix from the chromeos guys,
marked for stable.
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, fpu: Avoid FPU lazy restore after suspend
x86-32: Unbreak booting on some 486 clones
x86, kvm: Remove incorrect redundant assembly constraint
Pull assorted signal-related fixes from Al Viro:
"uml regression fix (braino in sys_execve() patch) + a bunch of fucked
sigaltstack-on-rt_sigreturn uses, similar to sparc64 fix that went in
through davem's tree. m32r horrors not included - that one's waiting
for maintainer."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
microblaze: rt_sigreturn is too trigger-happy about sigaltstack errors
score: do_sigaltstack() expects a userland pointer...
sh64: fix altstack switching on sigreturn
openrisk: fix altstack switching on sigreturn
um: get_safe_registers() should be done in flush_thread(), not start_thread()
* 'arm-privcmd-for-3.8' of git://xenbits.xen.org/people/ianc/linux:
xen: arm: implement remap interfaces needed for privcmd mappings.
xen: correctly use xen_pfn_t in remap_domain_mfn_range.
xen: arm: enable balloon driver
xen: balloon: allow PVMMU interfaces to be compiled out
xen: privcmd: support autotranslated physmap guests.
xen: add pages parameter to xen_remap_domain_mfn_range
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
After merging the xen-two tree, today's linux-next build (x86_64
allmodconfig) produced this warning:
arch/x86/xen/enlighten.c: In function 'init_hvm_pv_info':
arch/x86/xen/enlighten.c:1617:16: warning: unused variable 'ebx' [-Wunused-variable]
arch/x86/xen/enlighten.c:1617:11: warning: unused variable 'eax' [-Wunused-variable]
Introduced by commit 9d02b43dee ("xen PVonHVM: use E820_Reserved area
for shared_info").
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When a cpu enters S3 state, the FPU state is lost.
After resuming for S3, if we try to lazy restore the FPU for a process running
on the same CPU, this will result in a corrupted FPU context.
Ensure that "fpu_owner_task" is properly invalided when (re-)initializing a CPU,
so nobody will try to lazy restore a state which doesn't exist in the hardware.
Tested with a 64-bit kernel on a 4-core Ivybridge CPU with eagerfpu=off,
by doing thousands of suspend/resume cycles with 4 processes doing FPU
operations running. Without the patch, a process is killed after a
few hundreds cycles by a SIGFPE.
Cc: Duncan Laurie <dlaurie@chromium.org>
Cc: Olof Johansson <olofj@chromium.org>
Cc: <stable@kernel.org> v3.4+ # for 3.4 need to replace this_cpu_write by percpu_write
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: http://lkml.kernel.org/r/1354306532-1014-1-git-send-email-vpalatin@chromium.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
CPUID.7.0.EBX[1]=1 indicates IA32_TSC_ADJUST MSR 0x3b is supported
Basic design is to emulate the MSR by allowing reads and writes to a guest
vcpu specific location to store the value of the emulated MSR while adding
the value to the vmcs tsc_offset. In this way the IA32_TSC_ADJUST value will
be included in all reads to the TSC MSR whether through rdmsr or rdtsc. This
is of course as long as the "use TSC counter offsetting" VM-execution control
is enabled as well as the IA32_TSC_ADJUST control.
However, because hardware will only return the TSC + IA32_TSC_ADJUST +
vmsc tsc_offset for a guest process when it does and rdtsc (with the correct
settings) the value of our virtualized IA32_TSC_ADJUST must be stored in one
of these three locations. The argument against storing it in the actual MSR
is performance. This is likely to be seldom used while the save/restore is
required on every transition. IA32_TSC_ADJUST was created as a way to solve
some issues with writing TSC itself so that is not an option either.
The remaining option, defined above as our solution has the problem of
returning incorrect vmcs tsc_offset values (unless we intercept and fix, not
done here) as mentioned above. However, more problematic is that storing the
data in vmcs tsc_offset will have a different semantic effect on the system
than does using the actual MSR. This is illustrated in the following example:
The hypervisor set the IA32_TSC_ADJUST, then the guest sets it and a guest
process performs a rdtsc. In this case the guest process will get
TSC + IA32_TSC_ADJUST_hyperviser + vmsc tsc_offset including
IA32_TSC_ADJUST_guest. While the total system semantics changed the semantics
as seen by the guest do not and hence this will not cause a problem.
Signed-off-by: Will Auld <will.auld@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
In order to track who initiated the call (host or guest) to modify an msr
value I have changed function call parameters along the call path. The
specific change is to add a struct pointer parameter that points to (index,
data, caller) information rather than having this information passed as
individual parameters.
The initial use for this capability is for updating the IA32_TSC_ADJUST msr
while setting the tsc value. It is anticipated that this capability is
useful for other tasks.
Signed-off-by: Will Auld <will.auld@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Create a new subsystem that probes on kernel boundaries
to keep track of the transitions between level contexts
with two basic initial contexts: user or kernel.
This is an abstraction of some RCU code that use such tracking
to implement its userspace extended quiescent state.
We need to pull this up from RCU into this new level of indirection
because this tracking is also going to be used to implement an "on
demand" generic virtual cputime accounting. A necessary step to
shutdown the tick while still accounting the cputime.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
[ paulmck: fix whitespace error and email address. ]
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
These are three fixes for the Marvell EBU family and one for the Samsung
s3c platforms. All of them are obvious should still make it into 3.7.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zrCM
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"These are three fixes for the Marvell EBU family and one for the
Samsung s3c platforms. All of them are obvious should still make it
into 3.7."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: Kirkwood: Update PCI-E fixup
Dove: Fix irq_to_pmu()
Dove: Attempt to fix PMU/RTC interrupts
ARM: S3C24XX: Fix potential NULL pointer dereference error
These were originally prepared by Krzysztof Halasa but not submitted
in time for v3.7 due to some confusion about how ixp4xx patches should
be handled. Jason Cooper thankfully offered to help out sending the
patches upstream through arm-soc now, but given the timing, we could
as well delay them for 3.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=GlCa
-----END PGP SIGNATURE-----
Merge tag 'ixp4xx-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM ixp4xx bug fixes from Arnd Bergmann:
"These were originally prepared by Krzysztof Halasa but not submitted
in time for v3.7 due to some confusion about how ixp4xx patches should
be handled. Jason Cooper thankfully offered to help out sending the
patches upstream through arm-soc now, but given the timing, we could
as well delay them for 3.8."
* tag 'ixp4xx-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
IXP4xx: use __iomem for MMIO
IXP4xx: map CPU config registers within VMALLOC region.
IXP4xx: Always ioremap() Queue Manager MMIO region at boot.
ixp4xx: Declare MODULE_FIRMWARE usage
IXP4xx crypto: MOD_AES{128,192,256} already include key size.
WAN: Remove redundant HDLC info printed by IXP4xx HSS driver.
IXP4xx: Remove time limit for PCI TRDY to enable use of slow devices.
IXP4xx: ixp4xx_crypto driver requires Queue Manager and NPE drivers.
IXP4xx: HW pseudo-random generator is available on IXP45x/46x only.
IXP4xx: Fix off-by-one bug in Goramo MultiLink platform.
IXP4xx: Fix Goramo MultiLink platform compilation.
CC arch/arm/mach-sunxi/sunxi.o
./arch/arm/mach-sunxi/sunxi.c: In function 'sunxi_restart':
./arch/arm/mach-sunxi/sunxi.c:55:3: error: implicit declaration of function 'mdelay' [-Werror=implicit-function-declaration]
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
This is for Samsung board updates just for s3c64xx
* 'next/board-samsung-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Add dummy supplies for Glenfarclas LDOs
ARM: S3C64XX: Add registration of WM2200 Bells device on Cragganmore
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
This is including Samsung small updates(developments) for v3.8.
Add node PL330 MDMA1 and UART3 for DEBUG_LL and secondary cpu bring-up
for exynos4412.
* 'next/devel-samsung-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: add node for PL330 MDMA1 controller for exynos4
ARM: EXYNOS: Add support for secondary CPU bring-up on Exynos4412
ARM: EXYNOS: add UART3 to DEBUG_LL ports
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
Just adding camif gpio setup and clkdev.
* 'next/cam-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C24XX: Add clkdev entry for camif-upll clock
ARM: SAMSUNG: Add s3c24xx/s3c64xx CAMIF GPIO setup helpers
+ Linux 3.7-rc6
Conflicts due to the 3.7-rc6 sync: arch/arm/mach-highbank/system.c
include/linux/clk-provider.h, resolved as in other branches.
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
* 'next/pm-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add flush_cache_all in suspend finisher
ARM: EXYNOS: Remove scu_enable from cpuidle
ARM: EXYNOS: Fix soft reboot hang after suspend/resume
ARM: EXYNOS: Add support for rtc wakeup
ARM: EXYNOS: fix the hotplug for Cortex-A15
+ Linux 3.7-rc6
- Add support for l2x0 cache on mvebu boards
- Depends on mvebu/everything
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQtOFbAAoJEAi3KVZQDZAeRbkH/3IWYaAFXi6wnM4yHdYJbp5A
X1375b4Tkjd2Q05gujtNZLDS1gR4O65gJ9nxoV4OuYtqt1WnFUTDU4WozaYFdj8G
1hojkI6qKUddV+EZdMkx1/0YXORsNbGx8PHFPzsLfMHL/qEWjdMgOf4UW+9AogVt
hOwQwIs7SuhDnu0QR0dUH65iU848n5dYSczr/j71l2fqooJ/+KaU1hKKYf/rFvX2
3f9TaDydeglgAUGs7FUL1EbuLQiygIGy1wDhxyVK+g7inAzdQGzVZ7faK8M3NScM
YixWH+uy35ZAS8LlPCpY7DFts4pMtB/5fFvWiMYaBXv53mClgqSaymQDZLObJi8=
=rcOU
-----END PGP SIGNATURE-----
Merge tag 'mvebu_cache_l2x0_for_3.8' of git://git.infradead.org/users/jcooper/linux into late/mvebu
From Jason Cooper:
mvebu cache-l2x0 for v3.8
- Add support for l2x0 cache on mvebu boards
- Depends on mvebu/everything
* tag 'mvebu_cache_l2x0_for_3.8' of git://git.infradead.org/users/jcooper/linux:
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
- due to the complex interdependencies of the received pull requests
I decided to keep this in one branch the way they recommended merging it
- this was their first attempt at doing pull requests, we'll work on it
with them
- added SMP support for mvebu SoCs
- added coherency fabric
- added mdio and mvneta drivers
- added mirabox board
- added openblocks ax3-4 board
- clock fixes and improvements
- converted mv_xor driver to devicetree (extensive series in itself)
merge conflicts with orion/*
- arch/arm/mach-kirkwood/Kconfig
- select everything
- arch/arm/mach-kirkwood/board-dt.c
- remove AUXDATA
- keep all of_machine_is_compatible()
- use of_platform_populate(NULL, kirkwood_dt_match_table, NULL, NULL)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQsFAhAAoJEAi3KVZQDZAedzgH/3VodO3dDqL4A5HCoUj56HXF
Chkv1cl+1VS3sPnsbbluG0fmDdB619i4Oi2bUWc1YdLpEE0xgyjeAzl5vZDFBjrS
tb8nhWCd2vEcKFSC+HVU2Rhj0NwgUoQifoeD7NSovYZJE6+z+KEY5ny0sE4uaWE1
NL+StBI9dH+SvMi59rnsAxteAnBEAosUoY4KaoHcTHvPsqm9xW5GBh1MkSXQB7fx
kwRrdCaM8U3y3J933/Y4C3maDDQVL7v27YgQp+U5r/eRyN7fVVccxLr6xwl9sck2
fjEpbNRYMImvCOKh8+dhllf/8ZOmjdOore4ORbk4Ulame2KL6pG/2fZ+5N+FrRQ=
=QHBZ
-----END PGP SIGNATURE-----
Merge tag 'mvebu_everything_for_3.8' of git://git.infradead.org/users/jcooper/linux into late/mvebu
From Jason Cooper. Unfortunately this is a combined branch with all
mvebu code as one drop, something we normally try to avoid and instead
slice vendor topics across our branches. Hopefully we can avoid doing
this again for 3.9!
mvebu everything for v3.8
- due to the complex interdependencies of the received pull requests
I decided to keep this in one branch the way they recommended merging it
- this was their first attempt at doing pull requests, we'll work on it
with them
- added SMP support for mvebu SoCs
- added coherency fabric
- added mdio and mvneta drivers
- added mirabox board
- added openblocks ax3-4 board
- clock fixes and improvements
- converted mv_xor driver to devicetree (extensive series in itself)
* tag 'mvebu_everything_for_3.8' of git://git.infradead.org/users/jcooper/linux: (85 commits)
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
arm: mvebu: Add support for coherency fabric in mach-mvebu
arm: mvebu: update defconfig to include XOR driver
arm: mvebu: update defconfig to include network driver
...
Signed-off-by: Olof Johansson <olof@lixom.net>
All architectures that use cmd_dtc do so in almost the same way. Create
a central build rule to avoid duplication. The one difference is that
most current uses of dtc build $(obj)/%.dtb from $(src)/dts/%.dts rather
than building the .dtb in the same directory as the .dts file. This
difference will be eliminated arch-by-arch in future patches.
MIPS is the exception here; it already uses the exact same rule as the
new common rule, so the duplicate is removed in this patch to avoid any
conflict. arch/mips changes courtesy of Ralf Baechle.
Update Documentation/kbuild to remove the explicit call to cmd_dtc from
the example, now that the rule exists in a centralized location.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Olof Johansson <olof@lixom.net>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: linux-c6x-dev@linux-c6x.org
Cc: Mark Salter <msalter@redhat.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-xtensa@linux-xtensa.org
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
CONFIG_PCI is disabled by default currently.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add some s390 specific sysfs attributes to the PCI device directory.
The following attributes are introduced:
- function_id (PCI function ID)
- function_handle (PCI function handle)
- pchid (PCI channel ID)
- pfgid (PCI function group ID aka PCI root complex)
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add SCLP PCI configure/deconfigure and implement a PCI hotplug
controller (s390_pci_hpc). The hotplug controller creates a slot
for every PCI function in stand-by or configured state. The PCI
functions are named after the PCI function ID (fid). By writing to
the power attribute in /sys/bus/pci/slots/<fid>/power the PCI function
is moved to stand-by or configured state. If moved to the configured
state the device is automatically scanned by the s390 PCI layer.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add CHSC store-event-information support for PCI (notfication type 2)
and report error and availability events to the PCI architecture layer.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add DMA IOMMU support using 4K page table entries. Implement dma_map_ops.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Support PCI adapter interrupts using the Single-IRQ-mode. Single-IRQ-mode
disables an adapter IRQ automatically after delivering it until the SIC
instruction enables it again. This is used to reduce the number of IRQs
for streaming workloads.
Up to 64 MSI handlers can be registered per PCI function.
A hash table is used to map interrupt numbers to MSI descriptors.
The interrupt vector is scanned using the flogr instruction.
Only MSI/MSI-X interrupts are supported, no legacy INTs.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.
Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.
So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.
The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.
Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.
Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.
Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.
Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.
[1] https://patchwork.kernel.org/patch/1519591/#
cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JSAM
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/devel-prcm-signed' into omap-for-v3.8/cleanup-headers-prepare-multiplatform-v3
omap prcm changes via Paul Walmsley <paul@pwsan.com>:
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
Conflicts:
arch/arm/mach-omap2/cm33xx.c
arch/arm/mach-omap2/io.c
arch/arm/mach-omap2/prm_common.c
The flogr instruction scans a bitmap starting from the leftmost bit.
Implement support for these bitops. This could be useful to scan
bitmaps like an interrupt vector set by the hardware starting
at the leftmost bit.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CLP instructions are used to query the firmware about detected PCI
functions, the attributes of those functions and to enable or disable
a PCI function. The CLP interface is the equivalent to a PCI bus scan.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add PCI support for s390, (only 64 bit mode is supported by hardware):
- PCI facility tests
- PCI instructions: pcilg, pcistg, pcistb, stpcifc, mpcifc, rpcit
- map readb/w/l/q and writeb/w/l/q to pcilg and pcistg instructions
- pci_iomap implementation
- memcpy_fromio/toio
- pci_root_ops using special pcilg/pcistg
- device, bus and domain allocation
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
ERROR: "allnodes" [drivers/w1/masters/w1-gpio.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
[grant.likely: allnodes is too generic; rename to of_allnodes]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Ville Syrjala <syrjala@sci.fi>
Fix 32 vs 32k typo:
arch/arm/mach-omap2/timer.c: In function 'omap4_local_timer_init':
arch/arm/mach-omap2/timer.c:633:2: error: implicit declaration of function 'omap4_sync32_timer_init' [-Werror=implicit-function-declaration]
arch/arm/mach-omap2/timer.c: At top level:
arch/arm/mach-omap2/timer.c:610:2: warning: 'omap4_sync32k_timer_init' defined but not used [-Wunused-function]
Also, mark the omap4_local_timer_init() stub as __init (and take off
the explicit inline and let the compiler do the work instead).
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JSAM
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/devel-prcm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm2
From Tony Lindgren:
omap prcm changes via Paul Walmsley <paul@pwsan.com>:
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
* tag 'omap-for-v3.8/devel-prcm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (49 commits)
ARM: OMAP2+: omap_device: Correct resource handling for DT boot
ARM: OMAP2+: hwmod: Add possibility to count hwmod resources based on type
ARM: OMAP2+: hwmod: Add support for per hwmod/module context lost count
ARM: OMAP2+: PRM: initialize some PRM functions early
ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP2xxx: clock: drop obsolete clock data
ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP3+: DPLL: drop !CONFIG_COMMON_CLK sections
ARM: AM33xx: clock: drop obsolete clock data
ARM: OMAP3xxx: clk: drop obsolete clock data
ARM: OMAP3: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP44xx: clock: drop obsolete clock data
ARM: OMAP4: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP: hwmod: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP: clock: Switch to COMMON clk
ARM: OMAP2: clock: Add 24xx data using common struct clk
ARM: OMAP3: clock: Add 3xxx data using common struct clk
ARM: AM33XX: clock: add clock data in common clock format
ARM: OMAP4: clock: Add 44xx data using common struct clk
ARM: OMAP2+: clock: add OMAP CCF convenience macros to mach-omap2/clock.h
...
Some context conflicts due to nearby changes resolved in
arch/arm/mach-omap2/io.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
By Lee Jones (42) and others
via Olof Johansson (13) and others
* next/dt: (249 commits)
ARM: ux500: Rename dbx500 cpufreq code to be more generic
ARM: dts: add missing ux500 device trees
ARM: ux500: Stop registering the PCM driver from platform code
ARM: ux500: Move board specific GPIO info out to subordinate DTS files
ARM: ux500: Disable the MMCI gpio-regulator by default
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
...
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XZ+L
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Timer clean-up to get us closer to moving timer code to drivers,
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
By Jon Hunter (32) and others
via Tony Lindgren
* tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (71 commits)
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: OMAP2+: Fix compiler warning for 32k timer
ARM: OMAP: Remove unnecessary inclusion of dmtimer.h
ARM: OMAP: Add platform data header for DMTIMERs
ARM: OMAP: Remove unnecessary omap_dm_timer structure declaration
ARM: OMAP2+: Remove unnecessary local variable in timer code
ARM: OMAP: Don't store timers physical address
ARM: OMAP: Define omap_dm_timer_prepare function as static
ARM: OMAP: Clean-up dmtimer reset code
ARM: OMAP: Remove __omap_dm_timer_set_source function
ARM: OMAP: Remove unnecessary call to clk_get()
ARM: OMAP: Add dmtimer interrupt disable function
ARM: OMAP: Fix spurious interrupts when using timer match feature
ARM: OMAP: Don't restore DMTIMER interrupt status register
ARM: OMAP: Don't restore of DMTIMER TISTAT register
ARM: OMAP: Fix dmtimer reset for timer1
ARM: OMAP2+: Don't use __omap_dm_timer_reset()
ARM: OMAP2/3: Define HWMOD software reset status for DMTIMERs
ARM: OMAP3: Correct HWMOD DMTIMER SYSC register declarations
...
Change/change conflict in arch/arm/mach-omap2/board-cm-t3517.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
vmcs->cpu indicates whether it exists on the target cpu, -1 means the vmcs
does not exist on any vcpu
If vcpu load vmcs with vmcs.cpu = -1, it can be directly added to cpu's percpu
list. The list can be corrupted if the cpu prefetch the vmcs's list before
reading vmcs->cpu. Meanwhile, we should remove vmcs from the list before
making vmcs->vcpu == -1 be visible
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Per Alan Cox, Nx586 did not support WP in supervisor mode, making it a
386 by Linux kernel standards. As such, it is too unsupported now.
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Link: http://lkml.kernel.org/r/20121128205203.05868eab@pyramind.ukuu.org.uk
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Simplify the implementation of sync_core() for the case where we may
not have the CPUID instruction available.
[ v2: stylistic cleanup of the #else clause per suggestion by Borislav
Petkov. ]
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1354132230-21854-9-git-send-email-hpa@linux.intel.com
Cc: Borislav Petkov <bp@alien8.de>
* pm-cpuidle:
cpuidle: Measure idle state durations with monotonic clock
cpuidle: fix a suspicious RCU usage in menu governor
cpuidle: support multiple drivers
cpuidle: prepare the cpuidle core to handle multiple drivers
cpuidle: move driver checking within the lock section
cpuidle: move driver's refcount to cpuidle
cpuidle: fixup device.h header in cpuidle.h
cpuidle / sysfs: move structure declaration into the sysfs.c file
cpuidle: Get typical recent sleep interval
cpuidle: Set residency to 0 if target Cstate not enter
cpuidle: Quickly notice prediction failure in general case
cpuidle: Quickly notice prediction failure for repeat mode
cpuidle / sysfs: move kobj initialization in the syfs file
cpuidle / sysfs: change function parameter
* pm-cpufreq: (21 commits)
cpufreq: ondemand: update sampling rate only on right CPUs
cpufreq: SPEAr: Add CPUFreq driver
cpufreq: governors: Fix jiffies/cputime mixup (revisited)
cpufreq: ondemand: fix wrong delay sampling rate
cpufreq: exynos: Use static for functions used in only this file
cpufreq: exynos: Broadcast frequency change notifications for all cores
cpufreq: remove use of __devexit
cpufreq: remove use of __devinit
cpufreq: remove use of __devexit_p
cpufreq: Remove unnecessary initialization of a local variable
cpufreq: Make sure target freq is within limits
cpufreq: Avoid calling cpufreq driver's target() routine if target_freq == policy->cur
cpufreq: Fix sparse warning by making local function static
cpufreq: Fix sparse warnings by updating cputime64_t to u64
cpufreq: governors: remove redundant code
cpufreq: return early from __cpufreq_driver_getavg()
cpufreq: fix jiffies/cputime mixup in conservative/ondemand governors
cpufreq: Improve debug prints
cpufreq: Move common part from governors to separate file, v2
cpufreq / core: Fix printing of governor and driver name
...
* acpi-general: (38 commits)
ACPI / thermal: _TMP and _CRT/_HOT/_PSV/_ACx dependency fix
ACPI: drop unnecessary local variable from acpi_system_write_wakeup_device()
ACPI: Fix logging when no pci_irq is allocated
ACPI: Update Dock hotplug error messages
ACPI: Update Container hotplug error messages
ACPI: Update Memory hotplug error messages
ACPI: Update CPU hotplug error messages
ACPI: Add acpi_handle_<level>() interfaces
ACPI: remove use of __devexit
ACPI / PM: Add Sony Vaio VPCEB1S1E to nonvs blacklist.
ACPI / battery: Correct battery capacity values on Thinkpads
Revert "ACPI / x86: Add quirk for "CheckPoint P-20-00" to not use bridge _CRS_ info"
ACPI: create _SUN sysfs file
ACPI / memhotplug: bind the memory device when the driver is being loaded
ACPI / memhotplug: don't allow to eject the memory device if it is being used
ACPI / memhotplug: free memory device if acpi_memory_enable_device() failed
ACPI / memhotplug: fix memory leak when memory device is unbound from acpi_memhotplug
ACPI / memhotplug: deal with eject request in hotplug queue
ACPI / memory-hotplug: add memory offline code to acpi_memory_device_remove()
ACPI / memory-hotplug: call acpi_bus_trim() to remove memory device
...
Conflicts:
include/linux/acpi.h (two additions at the end of the same file)
Commit c22618a1, "drivers/of: Constify device_node->name and
->path_component_name" changes device_node name to a const value, but
the PowerPC scom code still assigns it to a non-void field in
debugfs_blob_wrapper. The /right/ solution might be to change the
debugfs_blob_wrapper->data to also be const, but that is a bit
risky. Instead, cast the value to (void*). It is a bit ugly, but it
is the safest change until it can be investigated where
debugfs_blob_wrapper can be modified.
Reported-by: Michael Neuling <mikey@neuling.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Kernel does not contain symbol HAVE_SPARSE_IRQ. Definition
in arch/arm64/Kconfig seems typo because valid symbol is
MAY_HAVE_SPARSE_IRQ.
In any case SPARSE_IRQ is selected by default and we just
remove selecting of this symbol.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The AArch64 Linux port relies on the mm code to wrprotect clean ptes.
This however is not the case with newly created ptes and
PAGE_SHARED(_EXEC) is writable but !dirty.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
From Kukjin Kim <kgene.kim@samsung.com>:
Samsung fixes for v3.7
* 'v3.7-samsung-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C24XX: Fix potential NULL pointer dereference error
This would have been ok to delay to 3.8 according to Kukjin, but since
it's an obvious bug fix and a potential NULL pointer dereference, it
seem appropriate for a late 3.7 submission.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We use XENMEM_add_to_physmap_range which is the preferred interface
for foreign mappings.
Acked-by: Mukesh Rathor <mukesh.rathor@oracle.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
From Jason Cooper <jason@lakedaemon.net>:
ixp4xx fixes for v3.7
* tag 'ixp4xx_fixes_for_3.7' of git://git.infradead.org/users/jcooper/linux:
IXP4xx: use __iomem for MMIO
IXP4xx: map CPU config registers within VMALLOC region.
IXP4xx: Always ioremap() Queue Manager MMIO region at boot.
ixp4xx: Declare MODULE_FIRMWARE usage
IXP4xx crypto: MOD_AES{128,192,256} already include key size.
WAN: Remove redundant HDLC info printed by IXP4xx HSS driver.
IXP4xx: Remove time limit for PCI TRDY to enable use of slow devices.
IXP4xx: ixp4xx_crypto driver requires Queue Manager and NPE drivers.
IXP4xx: HW pseudo-random generator is available on IXP45x/46x only.
IXP4xx: Fix off-by-one bug in Goramo MultiLink platform.
IXP4xx: Fix Goramo MultiLink platform compilation.
These were originally prepared by Krzysztof Halasa but not submitted
in time for v3.7 due to some confusion about how ixp4xx patches should
be handled. Jason thankfully offered to help out sending the patches
upstream through arm-soc now, but given the timing, I did not feel
comfortable sending them just before the 3.8 merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
For Xen on ARM a PFN is 64 bits so we need to use the appropriate
type here.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v2: include the necessary header,
Reported-by: Fengguang Wu <fengguang.wu@intel.com> ]
The code is now in a state where can just enable it.
Drop the *_xenballloned_pages duplicates since these are now supplied
by the balloon code.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The ARM platform has no concept of PVMMU and therefor no
HYPERVISOR_update_va_mapping et al. Allow this code to be compiled out
when not required.
In some similar situations (e.g. P2M) we have defined dummy functions
to avoid this, however I think we can/should draw the line at dummying
out actual hypercalls.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Also introduce xen_unmap_domain_mfn_range. These are the parts of
Mukesh's "xen/pvh: Implement MMU changes for PVH" which are also
needed as a baseline for ARM privcmd support.
The original patch was:
Signed-off-by: Mukesh Rathor <mukesh.rathor@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This derivative is also:
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
This patch adds support for DMA_ATTR_FORCE_CONTIGUOUS attribute for
dma_alloc_attrs() in IOMMU-aware implementation. For allocating physically
contiguous buffers Contiguous Memory Allocator is used.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
the first one is equal to signal_pt_regs(), the second is never used
(and always NULL, while we are at it).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Always equal to task_pt_regs(current); defined only when we are in
signal delivery. It may be different from current_pt_regs() - e.g.
architectures like m68k may have pt_regs location on exception
different from that on a syscall and signals (just as ptrace handling)
may happen on exceptions as well as on syscalls.
When they are equal, it's often better to have signal_pt_regs
defined (in asm/ptrace.h) as current_pt_regs - that tends to be
optimized better than default would be. However, optimisation is
the only reason why we might want an arch-specific definition;
if current_pt_regs() and task_pt_regs(current) have different
values, the latter one is right.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... and get rid of idiotic struct pt_regs * in asm-generic/syscalls.h
prototypes of the same, while we are at it. Eventually we want those
in linux/syscalls.h, of course, but that'll have to wait a bit.
Note that there are *three* variants of sys_clone() order of arguments.
Braindamage galore...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* no need to restore everything from switch_stack when we only need $26
* no need to pass current_pt_regs() manually, we can just as easily
calculate it in alpha_clone/alpha_vfork ($8 + constant)
* interpretation of zero usp as "use the parent's" is simpler in copy_thread();
let fork and vfork just pass 0.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
incidentally, declaring a local variable as __user (!) to make
sparse STFU is really sick. Especially since sparse had been
100% right - it *is* a bug.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In loaded_vmcs_clear, loaded_vmcs->cpu is the fist parameter passed to
smp_call_function_single, if the target cpu is downing (doing cpu hot remove),
loaded_vmcs->cpu can become -1 then -1 is passed to smp_call_function_single
It can be triggered when vcpu is being destroyed, loaded_vmcs_clear is called
in the preemptionable context
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
As Frederic pointed idle_cpu() may return false even if async fault
happened in the idle task if wake up is pending. In this case the code
will try to put idle task to sleep. Fix this by using is_idle_task() to
check for idle task.
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As on ia64 builds we get:
include/xen/interface/version.h: In function 'xen_running_on_version_or_later':
include/xen/interface/version.h:76: error: implicit declaration of function 'HYPERVISOR_xen_version'
We can later on make this function exportable if there are
modules using part of it. For right now the only two users are
built-in.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Some internal kernel symbols were referenced in the exported setup.h.
This splits out the internal bits from the exported uapi bits.
Signed-off-by: Mark Salter <msalter@redhat.com>
The recent commit "ARM: EXYNOS: add support for EXYNOS5440 SoC" broke
support for exynos5250 because of_machine_is_compatible() was used too
early in the boot process. It also probably meant that the exynos5440
failed to use the proper iotable. Switch to use
of_flat_dt_is_compatible() in both of these cases.
The failure I was seeing in exynos5250 because of this was:
Division by zero in kernel.
[<80015ed4>] (unwind_backtrace+0x0/0xec) from [<8045c7a4>] (dump_stack+0x20/0x24)
[<8045c7a4>] (dump_stack+0x20/0x24) from [<80012990>] (__div0+0x20/0x28)
[<80012990>] (__div0+0x20/0x28) from [<8021ab04>] (Ldiv0_64+0x8/0x18)
[<8021ab04>] (Ldiv0_64+0x8/0x18) from [<80068560>] (__clocksource_updatefreq_scale+0x54/0x134)
[<80068560>] (__clocksource_updatefreq_scale+0x54/0x134) from [<8006865c>] (__clocksource_register_scale+0x1c/0x54)
[<8006865c>] (__clocksource_register_scale+0x1c/0x54) from [<80612a18>] (exynos_timer_init+0x100/0x1e8)
[<80612a18>] (exynos_timer_init+0x100/0x1e8) from [<8060d184>] (time_init+0x28/0x38)
[<8060d184>] (time_init+0x28/0x38) from [<8060a754>] (start_kernel+0x1e0/0x3c8)
[<8060a754>] (start_kernel+0x1e0/0x3c8) from [<40008078>] (0x40008078)
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
[olofj: fixed two build errors, one missing include and one !CONFIG_OF failure]
Signed-off-by: Olof Johansson <olof@lixom.net>
Add dma-debug interface debug_dma_mapping_error() to debug drivers that fail
to check dma mapping errors on addresses returned by dma_map_single() and
dma_map_page() interfaces.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Add dma-debug interface debug_dma_mapping_error() to debug drivers that fail
to check dma mapping errors on addresses returned by dma_map_single() and
dma_map_page() interfaces.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Add dma-debug interface debug_dma_mapping_error() to debug drivers that fail
to check dma mapping errors on addresses returned by dma_map_single() and
dma_map_page() interfaces.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Add dma-debug interface debug_dma_mapping_error() to debug drivers that fail
to check dma mapping errors on addresses returned by dma_map_single() and
dma_map_page() interfaces.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Add support for debug_dma_mapping_error() call to avoid warning from
debug_dma_unmap() interface when it checks for mapping error checked
status. Without this patch, device driver failed to check map error
warning is generated.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Add dma-debug interface debug_dma_mapping_error() to debug drivers that fail
to check dma mapping errors on addresses returned by dma_map_single() and
dma_map_page() interfaces.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Add dma-debug interface debug_dma_mapping_error() to debug drivers that fail
to check dma mapping errors on addresses returned by dma_map_single() and
dma_map_page() interfaces.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Acked-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Add dma-debug interface debug_dma_mapping_error() to debug drivers that fail
to check dma mapping errors on addresses returned by dma_map_single() and
dma_map_page() interfaces.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Add the registers used to configure the CSI-2 receiver PHY on OMAP3430 and
3630 and map them in the ISP driver. The register is part of the control
block but it only is needed by the ISP driver.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The OMAP_I2C_FLAG_RESET_REGS_POSTIDLE is not used anymore
in the i2c driver. Remove the flag.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The SP804 driver statically initialises the cpumask of the clock event
device to be cpu_all_mask, which is derived from the compile-time
constant NR_CPUS. This breaks SMP_ON_UP systems where the interrupt
controller handling the sp804 doesn't have the irq_set_affinity callback
on the irq_chip, because the common timer code fails to identify the
device as cpu-local and ends up treating it as a broadcast device
instead.
This patch fixes the problem by using cpu_possible_mask at runtime,
which will correctly represent the possible CPUs when SMP_ON_UP is being
used.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* linus/master: (1428 commits)
futex: avoid wake_futex() for a PI futex_q
watchdog: using u64 in get_sample_period()
writeback: put unused inodes to LRU after writeback completion
mm: vmscan: check for fatal signals iff the process was throttled
Revert "mm: remove __GFP_NO_KSWAPD"
proc: check vma->vm_file before dereferencing
UAPI: strip the _UAPI prefix from header guards during header installation
include/linux/bug.h: fix sparse warning related to BUILD_BUG_ON_INVALID
Linux 3.7-rc7
powerpc/eeh: Do not invalidate PE properly
ALSA: hda - Fix build without CONFIG_PM
of/address: sparc: Declare of_iomap as an extern function for sparc again
PM / QoS: fix wrong error-checking condition
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
MPI: Fix compilation on MIPS with GCC 4.4 and newer
MIPS: Fix crash that occurs when function tracing is enabled
MIPS: Merge overlapping bootmem ranges
jbd: Fix lock ordering bug in journal_unmap_buffer()
...
These GPIO init and exit functions have no place in platform data, they
should be part of the driver instead,
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We're currently carrying two 'struct bu21013_platform_device's which
are identical for no apparent reason. Here we remove the extra burden
and apply the same information to the two different instances of the
bu21012_tp driver registration.
[Dmitry Torokhov: picked it up to (hopefully) reduce merge conflict with
bu21013_ts update that follows.]
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As requested by Glauber, do not update kvmclock area on vcpu->pcpu
migration, in case the host has stable TSC.
This is to reduce cacheline bouncing.
Acked-by: Glauber Costa <glommer@parallels.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
With master clock, a pvclock clock read calculates:
ret = system_timestamp + [ (rdtsc + tsc_offset) - tsc_timestamp ]
Where 'rdtsc' is the host TSC.
system_timestamp and tsc_timestamp are unique, one tuple
per VM: the "master clock".
Given a host with synchronized TSCs, its obvious that
guest TSC must be matched for the above to guarantee monotonicity.
Allow master clock usage only if guest TSCs are synchronized.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
KVM added a global variable to guarantee monotonicity in the guest.
One of the reasons for that is that the time between
1. ktime_get_ts(×pec);
2. rdtscll(tsc);
Is variable. That is, given a host with stable TSC, suppose that
two VCPUs read the same time via ktime_get_ts() above.
The time required to execute 2. is not the same on those two instances
executing in different VCPUS (cache misses, interrupts...).
If the TSC value that is used by the host to interpolate when
calculating the monotonic time is the same value used to calculate
the tsc_timestamp value stored in the pvclock data structure, and
a single <system_timestamp, tsc_timestamp> tuple is visible to all
vcpus simultaneously, this problem disappears. See comment on top
of pvclock_update_vm_gtod_copy for details.
Monotonicity is then guaranteed by synchronicity of the host TSCs
and guest TSCs.
Set TSC stable pvclock flag in that case, allowing the guest to read
clock from userspace.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Register a notifier for clocksource change event. In case
the host switches to clock other than TSC, disable master
clock usage.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Improve performance of time system calls when using Linux pvclock,
by reading time info from fixmap visible copy of pvclock data.
Originally from Jeremy Fitzhardinge.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Hook into generic pvclock vsyscall code, with the aim to
allow userspace to have visibility into pvclock data.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Originally from Jeremy Fitzhardinge.
Introduce generic, non hypervisor specific, pvclock initialization
routines.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Originally from Jeremy Fitzhardinge.
So code can be reused.
Acked-by: Glauber Costa <glommer@parallels.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Originally from Jeremy Fitzhardinge.
We can copy the information directly from "struct pvclock_vcpu_time_info",
remove pvclock_shadow_time.
Reviewed-by: Glauber Costa <glommer@parallels.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Originally from Jeremy Fitzhardinge.
pvclock_get_time_values, which contains the memory barriers
will be removed by next patch.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
We want to expose the pvclock shared memory areas, which
the hypervisor periodically updates, to userspace.
For a linear mapping from userspace, it is necessary that
entire page sized regions are used for array of pvclock
structures.
There is no such guarantee with per cpu areas, therefore move
to memblock_alloc based allocation.
Acked-by: Glauber Costa <glommer@parallels.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Otherwise its possible for an unrelated KVM_REQ_UPDATE_CLOCK (such as due to CPU
migration) to clear the bit.
Noticed by Paolo Bonzini.
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Reviewed-by: Glauber Costa <glommer@parallels.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Add missing PL330 MDMA1 controller node to the device tree (DT).
[ Currently there is no problem with using 'non-secure' mdma1 address
instead of 'secure' one on revision 0 of Exynos4210 SOC (as used by
Universal C210 board) as this SOC revision is unsupported by DT. ]
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos4412 uses different information register for each core. This
patch adjusts the bring-up code to take that into account.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for using UART3 for DEBUG_LL on exynos.
[dianders: added depend on ARCH_EXYNOS.]
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The s3c-camif driver uses "camera" clock conn_id for the "camif-upll"
(s3c244x) and "camera" (s3c64xx) platform clock. By adding this new
clkdev entry the platform differences are isolated from the driver.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds default helper functions for the camera port
pin configuration. Whenever pinctrl support for s3c24xx/s3c64xx
SoCs is available these code should be removed and proper pinctrl
API should be used in the CAMIF driver.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
With device tree support enabled for dwmci controller, the unused
non-dt support for dwmci controller can be removed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
[kgene.kim@samsung.com: updated as per Seungwon Jeon's pointing out]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The core cpu_suspend code no longer calls flush_cache_all to
optimize the cpu idle flow. Add a call for the same in the
exynos specific suspend code.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cortex A9 based exynos4 has a memory mapped SCU while the Cortex
A15 based exynos5 does not. Hence, remove the call to scu_enable
for exynos5.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Inderpal Singh <inderpal.singh@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Upon wake-up, clear the sleep mode set in INFORM1 register.
Signed-off-by: Inderpal Singh <inderpal.singh@samsung.com>
Tested-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Set the gic arch extension callback to support rtc wakeup.
Signed-off-by: Inderpal Singh <inderpal.singh@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The sequence of cpu_enter_lowpower() for Cortex-A15 is
different from the sequence for Cortex-A9. This patch
implements cpu_enter_lowpower() for EXYNOS5 SoC which
has Cortex-A15 cores.
Basded on original patch has been submitted by Changhwan Youn
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
[kgene.kim@samsung.com: use flush_cache_louis() instead of
flush_cache_all() as per Lorenzo and Santosh's suggestion]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
These are not actually connected but it saves them going through probe
deferral.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There appear to have been some 486 clones, including the "enhanced"
version of Am486, which have CPUID but not CR4. These 486 clones had
only the FPU flag, if any, unlike the Intel 486s with CPUID, which
also had VME and therefore needed CR4.
Therefore, look at the basic CPUID flags and require at least one bit
other than bit 0 before we modify CR4.
Thanks to Christian Ludloff of sandpile.org for confirming this as a
problem.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Many cpuidle drivers measure their time spent in an idle state by
reading the wallclock time before and after idling and calculating the
difference. This leads to erroneous results when the wallclock time gets
updated by another processor in the meantime, adding that clock
adjustment to the idle state's time counter.
If the clock adjustment was negative, the result is even worse due to an
erroneous cast from int to unsigned long long of the last_residency
variable. The negative 32 bit integer will zero-extend and result in a
forward time jump of roughly four billion milliseconds or 1.3 hours on
the idle state residency counter.
This patch changes all affected cpuidle drivers to either use the
monotonic clock for their measurements or make use of the generic time
measurement wrapper in cpuidle.c, which was already working correctly.
Some superfluous CLIs/STIs in the ACPI code are removed (interrupts
should always already be disabled before entering the idle function, and
not get reenabled until the generic wrapper has performed its second
measurement). It also removes the erroneous cast, making sure that
negative residency values are applied correctly even though they should
not appear anymore.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
SPEAr is an ARM based family of SoCs. This patch adds in support of cpufreq
driver for SPEAr SoCs. It is supported via DT only and so bindings are present
in binding document.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
From Lee Jones <lee.jones@linaro.org>:
* 'ste-dt-for-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Rename dbx500 cpufreq code to be more generic
ARM: dts: add missing ux500 device trees
ARM: ux500: Stop registering the PCM driver from platform code
ARM: ux500: Move board specific GPIO info out to subordinate DTS files
ARM: ux500: Disable the MMCI gpio-regulator by default
This follows up on the previous ux500 DT changes. Most importantly, it
resolves a build error in the dts files that was the result of referring
to a board specific device node from the common dtsi file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cpufreq driver doesn't only handle the db8500 anymore. There
are new variants which rely on it too, so we've renamed the
driver to be more generic.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds hrefprev60, hrefv60plus and ccu9540 to device trees compiled
during build.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
We now initialise the PCM driver through the MSP DAI, so there is
no need to register it though platform code anymore. This patch
strips out all PCM platform registration.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
GPIO numbers for the newly created gpio-regulator will differ from
board to board. Therefore it's not sensible to leave this information
in the top level DTSI file. Let's move them out to the DTS files
where they can correctly vary.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Not all supported boards will require a MMCI gpio-regulator,
therefore it's a good idea to only enable the node when and if
it is required. Let's disable it by default.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
do clk_get on connection id "fck" to support OMAP based
platforms having multiple clocks for module. Without this
driver change clk_get fails on am335x.
This patch is based on the discussion in community
http://marc.info/?l=linux-kernel&m=135166018907827&w=2
Signed-off-by: Manjunathappa <prakash.pm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Configure below LCDC configurations to optimal values, also have an
option configure these optional parameters for platform.
1) AC bias configuration: Required only for passive panels
2) Dma_burst_size:
3) FIFO_DMA_DELAY:
4) FIFO threshold: Does not apply for da830 LCDC.
Patch is verified for 16bpp and 24bpp configurations on da830, da850 and
am335x EVMs.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Merge SH Mobile LCDC patches from Laurent.
* 'lcdc-next' of git://linuxtv.org/pinchartl/fbdev:
fbdev: sh_mobile_lcdc: Make sh_mobile_lcdc_sys_bus_ops static
sh: kfr2r09: Use the backlight API for brightness control
ARM: mach-shmobile: ag5evm: Use the backlight API for brightness control
fbdev: sh_mobile_lcdc: Remove unused get_brightness pdata callback
sh: ecovec24: Remove unused get_brightness LCDC callback
sh: ap325rxa: Remove unused get_brightness LCDC callback
ARM: mach-shmobile: mackerel: Removed unused get_brightness callback
fbdev: sh_mobile_lcdc: Store the backlight brightness internally
fbdev: sh_mipi_dsi: Remove the unused sh_mipi_dsi_info lcd_chan field
ARM: mach-shmobile: Remove the unused sh_mipi_dsi_info lcd_chan field
fbdev: sh_mipi_dsi: Remove last reference to LCDC platform data
fbdev: sh_mipi_dsi: Use the LCDC entity default mode
fbdev: sh_mipi_dsi: Use the sh_mipi_dsi_info channel field
ARM: mach-shmobile: Initiliaze the new sh_mipi_dsi_info channel field
fbdev: sh_mipi_dsi: Add channel field to platform data
ARM: mach-shmobile: ag5evm: Add LCDC tx_dev field to platform data
fbdev: sh_mobile_lcdc: Remove priv argument from channel and overlay init
fbdev: sh_mobile_lcdc: Rename mode argument to modes
fbdev: sh_mobile_lcdc: Get display dimensions from the channel structure
fbdev: sh_mobile_lcdc: use dma_mmap_coherent
Pull ARM fixes from Russell King:
"Not much here, just a couple minor/cosmetic fixes and a patch for the
decompressor which fixes problems with modern GCC and CPUs."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7583/1: decompressor: Enable unaligned memory access for v6 and above
ARM: 7572/1: proc-v6.S: fix comment
ARM: 7570/1: quiet down the non make -s output
In __emulate_1op_rax_rdx, we use "+a" and "+d" which are input/output
constraints, and *then* use "a" and "d" as input constraints. This is
incorrect, but happens to work on some versions of gcc.
However, it breaks gcc with -O0 and icc, and may break on future
versions of gcc.
Reported-and-tested-by: Melanie Blower <melanie.blower@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/B3584E72CFEBED439A3ECA9BCE67A4EF1B17AF90@FMSMSX107.amr.corp.intel.com
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Issues that need to be handled:
* Handle PIC interrupts on any CPU irrespective of the apic mode
* In the apic lowest priority logical flat delivery mode, be prepared to
handle the interrupt on any CPU irrespective of what the IO-APIC RTE says.
* Because of above, when the IO-APIC starts handling the legacy PIC interrupt,
use the same vector that is being used by the PIC while programming the
corresponding IO-APIC RTE.
Start with all the cpu's in the legacy PIC interrupts cfg->domain.
By the time IO-APIC starts taking over the PIC interrupts, apic driver
model is finalized. So depend on the assign_irq_vector() to update the
cfg->domain and retain the same vector that was used by PIC before.
For the logical apic flat mode, cfg->domain is updated (during the first
call to assign_irq_vector()) to contain all the possible online cpu's (0xff).
Vector used for the legacy PIC interrupt doesn't change when the IO-APIC
starts handling the interrupt. Any interrupt migration after that
doesn't change the cfg->domain or the vector used.
For other apic modes like physical mode, cfg->domain is updated
(during the first call to assign_irq_vector()) to the boot cpu (cpu-0),
with the same vector that is being used by the PIC. When that interrupt is
migrated to a different cpu, cfg->domin and the vector assigned will change
accordingly.
Tested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1353970176.21070.51.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
A comment in entry.S incorrectly stated that interrupt vectors
called __do_IRQ() and that int6 vector was used for syscalls.
Both statements are incorrect for the current kernel, so this
patch cleans up the wording to reflect current reality.
Signed-off-by: Mark Salter <msalter@redhat.com>
This series will do the following:
- Switch the Integrator/AP and /CP to use the SoC bus
when booting from device tree.
- Group all devices on the SoC below this bus so as to
set a good example of how to do this. The bus was
invented by Lee Jones, let's show how it's to be used
on a DT:ed SoC.
- Fetch the special system controller offsets from two
special device tree nodes for each case and replace
the static mappings with these at boot.
- Move some static remaps to the ATAG-only code path
and delete some static maps that aren't used.
- Push dependencies on system controller remaps down
to the Integrator/AP board file and the PCIv3 driver
respectively and use only dynamic remappings.
- Fix up conditional BUG() usage in the PCIv3 driver
to be simpler and more to the point.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zpgo
-----END PGP SIGNATURE-----
Merge tag 'integrator-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/cleanup
From Linus Walleij <linus.walleij@linaro.org>:
This series will do the following:
- Switch the Integrator/AP and /CP to use the SoC bus
when booting from device tree.
- Group all devices on the SoC below this bus so as to
set a good example of how to do this. The bus was
invented by Lee Jones, let's show how it's to be used
on a DT:ed SoC.
- Fetch the special system controller offsets from two
special device tree nodes for each case and replace
the static mappings with these at boot.
- Move some static remaps to the ATAG-only code path
and delete some static maps that aren't used.
- Push dependencies on system controller remaps down
to the Integrator/AP board file and the PCIv3 driver
respectively and use only dynamic remappings.
- Fix up conditional BUG() usage in the PCIv3 driver
to be simpler and more to the point.
* tag 'integrator-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
ARM: integrator: hook the CP into the SoC bus
ARM: integrator: hook the AP into the SoC bus
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since the clk framework has already taken necessary locks before calling
into the arch clk ops code, no further locks are needed while setting
the parent of dsib clk. This patch removes a comment that indicated
otherwise, and yet did not take any locks.
Signed-off-by: Sivaram Nair <sivaramn@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
For Tegra30, pll_p clk's parent is wrongly specified as clk_m instead of
pll_ref in the tegra30_clk_init_table and this is resulting in a
boot-time warning. This patch fixes this by correcting the clk init
table.
Signed-off-by: Sivaram Nair <sivaramn@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
With Xen acpi pad logic added into kernel, we can now revert xen mwait related
patch df88b2d96e ("xen/enlighten: Disable
MWAIT_LEAF so that acpi-pad won't be loaded. "). The reason is, when running under
newer Xen platform, Xen pad driver would be early loaded, so native pad driver
would fail to be loaded, and hence no mwait/monitor #UD risk again.
Another point is, only Xen4.2 or later support Xen acpi pad, so we won't expose
mwait cpuid capability when running under older Xen platform.
Signed-off-by: Liu, Jinsong <jinsong.liu@intel.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Patch f055f1f6 [ARM: sunxi: Add sun4i and cubieboard support] missed
this sun4i.dtsi include file. This patch finally brings it upstream
enabling support for sun4i boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Pgtable bits are assigned dynamically depending on processor feature and
statically based on kernel configuration. To make sense out of the
disassembled TLB exception handlers a list of the actual assignments
used for a particular configuration and hardware setup can be very useful.
Output the actual TLB exception handlers in a format that simplifies their
post processsing from dmesg output.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
From a software perspective R5000 and R5000A are the same thing which is
why the symbol CPU_R5000A never got used, so finally delete it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Correct option should be LEDS_TRIGGERS, not LEDS_TRIGGER.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The kvm_seq value has nothing to do what so ever with this other KVM.
Given that KVM support on ARM is imminent, it's best to rename kvm_seq
into something else to clearly identify what it is about i.e. a sequence
number for vmalloc section mappings.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves shirq interrupt controllers driver and header file out of
plat-spear directory. It is moved to drivers/irqchip/ directory.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
shirq layer has been adapted to DT, add corresponding nodes in all
SPEAr3xx variants.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
SPEAr3xx architecture includes shared/multiplexed irqs for certain set
of devices. The multiplexor provides a single interrupt to parent
interrupt controller (VIC) on behalf of a group of devices.
There can be multiple groups available on SPEAr3xx variants but not
exceeding 4. The number of devices in a group can differ, further they
may share same set of status/mask registers spanning across different
bit masks. Also in some cases the group may not have enable or other
registers. This makes software little complex.
Present implementation was non-DT and had few complex data structures to
decipher banks, number of irqs supported, mask and registers involved.
This patch simplifies the overall design and convert it in to DT. It
also removes all registration from individual SoC files and bring them
in to common shirq.c.
Also updated the corresponding documentation for DT binding of shirq.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch fixes the platform data for compact flash controller.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Few fields are not required to be programmed in platform data of spi controller
now, as it comes via DT. Remove them.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch moves some global macro definitions to the files where they are used.
Its a step towards removing spear.h completely later on.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
amba-pl011 driver supports two pin state "default" and "sleep" and it
expect from dt to provide this pinctrl states and phandler otherwise it
gives a warning message.
To remove this warning message pass default state with null phandler to uart
pins in device node (In our case all the pins are configured in default states
so we pass null phandler to pins).
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch modifies the DT bindings for the GMAC IP existings for the
SPEAr family. The DT bindings now additionally pass the phy mode as a
configuration parameter for the ethernet device.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
SPEAr platform provides a provision to control chipselects of ARM PL022 Prime
Cell spi controller through its system registers, which otherwise remains under
PL022 control which some protocols do not want.
This patch adds spics controller nodes in device tree for various SPEAr13xx
SoCs.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Merge in orion's cleanup branch together with the DT contents. Ideally
the cleanup branch should have been the base for the DT branch to avoid
these, but that was missed when first merging. So we're doing it now to
reduce the amount of silly conflicts due to internal tree organization.
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge in the cleanups that should have been used as the base of the DT
branch instead of letting the conflicts be exposed all the way up to
the toplevel merges.
All of these are caused by cleanups being done both in the cleanup branch
and the dt branch, resulting in remove/remove conflicts of header files.
By Andrew Lunn (3) and others
via Jason Cooper
* orion/cleanup:
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
Remove/remove conflicts in:
arch/arm/mach-kirkwood/board-dockstar.c
arch/arm/mach-kirkwood/board-goflexnet.c
arch/arm/mach-kirkwood/board-lsxl.c
Signed-off-by: Olof Johansson <olof@lixom.net>
- ehci-orion dt binding
- gpio-poweroff
- use dt regulators
- move mpp to DT/pinctrl
Depends on:
- orion/boards
- merge conflicts
- keep all 'select's in Kconfig
- remove all #includes in board-*.c
- pinctrl/devel up to:
- 06763c7 pinctrl: mvebu: move to its own directory
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQsEfdAAoJEAi3KVZQDZAeBd8IAIAkBGIJyUJSmQJEWkZ/9ezq
UOLec1t/TnLhAQ1Sk8g4C41wmHKYNqmZSVaAXC+QP6Yw+Gdhlw+V6YBjOYDzA7Y4
k8ljw3SFbvS+AIx0qK26j6Tf6En2H5lMXsdlKoarCV+G+MxAHsQO7jL6y7BFwTlX
QnwJFz+NRzMFxaPiCS+43oZuxIIzkHe8wKMb0y7nSiNQYUUv8TdKvyK+ekFuszOp
v6uo/MI1p1/xdUxDbEKxOwmUjAy7x+t0LUFi1dsWuiDHdrG+BVT4NkJuFaD8Ui13
VoUD1ogyWHQZV2hq0dfj+9Hed5NEgl6toAzGN9LPLmsuVUXCnB2CdBprhuDv5F8=
=yaX1
-----END PGP SIGNATURE-----
Merge tag 'orion_dt_for_3.8' of git://git.infradead.org/users/jcooper/linux into next/dt
From Jason Cooper:
orion dt for v3.8
- ehci-orion dt binding
- gpio-poweroff
- use dt regulators
- move mpp to DT/pinctrl
Depends on:
- orion/boards
- merge conflicts
- keep all 'select's in Kconfig
- remove all #includes in board-*.c
- pinctrl/devel up to:
- 06763c7 pinctrl: mvebu: move to its own directory
* tag 'orion_dt_for_3.8' of git://git.infradead.org/users/jcooper/linux: (211 commits)
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
ARM: Kirkwood: Convert dnskw to pinctrl
ARM: Kirkwood: Convert iConnect to pinctrl.
ARM: Kirkwood: Convert TS219 to pinctrl.
ARM: Kirkwood: Add DTSI files for pinctrl
ARM: Kirkwood: Make use of mvebu pincltl and gpio drivers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- mach-orion5x/ joins the dark side! (devicetree)
- Lacie Network Space family
- Lacie Ethernet Disk mini v2
- USI TopKick
- ZyXEL NSA310
- MPL CEC4
- Plat'Home OpenBlocks A6 (kirkwood, AX3-4 is armada xp)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQrc/qAAoJEAi3KVZQDZAeGIcIAJ70hcz/cKdEKNpekMRoMWpz
LoDXtPqRuUvCqBdUNFkJyPAhHHkWwnU6KRcBRz1dknTtJ7nyCkDQYRG/JIroIs8I
X9N6JbPH7FMU+Z1ZUAM2ww+pEAIQkwX06erAy9u/a7ivMj/0LeXboNK+ngIx1jgL
xz2SS4wJrujPwvT2rYo4nJ+WwGiiIPbRjiY7r87rD/DQ9nY9DxKgfve7pRhaCCZS
Baw48u8qTe6M9LGcXw+b/MSHGCTB6YabqaRHMAr/1NK0Z3JDGU8tEpOuMCnFX7SA
6CxEymw5/8fzyTgdRz7FRd9Hg28y5Cd+T2l48X4tSL/M16H4EeBOxj6ub4zCi9s=
=nsDw
-----END PGP SIGNATURE-----
Merge tag 'orion_boards_for_3.8' of git://git.infradead.org/users/jcooper/linux into next/boards
From Jason Cooper:
orion boards for v3.8
- mach-orion5x/ joins the dark side! (devicetree)
- Lacie Network Space family
- Lacie Ethernet Disk mini v2
- USI TopKick
- ZyXEL NSA310
- MPL CEC4
- Plat'Home OpenBlocks A6 (kirkwood, AX3-4 is armada xp)
* tag 'orion_boards_for_3.8' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: Add Plat'Home OpenBlocks A6 support
ARM: Dove: update defconfig
ARM: Kirkwood: update defconfig for new boards
arm: orion5x: add DT related options in defconfig
arm: orion5x: convert 'LaCie Ethernet Disk mini v2' to Device Tree
arm: orion5x: basic Device Tree support
arm: orion5x: mechanical defconfig update
ARM: kirkwood: Add support for the MPL CEC4
arm: kirkwood: add support for ZyXEL NSA310
ARM: Kirkwood: new board USI Topkick
ARM: kirkwood: use gpio-fan DT binding on lsxl
ARM: Kirkwood: add Netspace boards to defconfig
ARM: kirkwood: DT board setup for Network Space Mini v2
ARM: kirkwood: DT board setup for Network Space Lite v2
ARM: kirkwood: DT board setup for Network Space v2 and parents
leds: leds-ns2: add device tree binding
ARM: Kirkwood: Enable the second I2C bus
- remove unused includes in kirkwood
- fix sparse warnings in kirkwood
- checkpatch cleanup in kirkwood
- use common code in pcie on kirkwood
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQrbKoAAoJEAi3KVZQDZAeojYH/0m7nrIMrLQ1A9FjglAzZQrE
Q7UrP4HWlTnG+aNF4a0G4CpO+vZYJd6mSKW3kP18AuncCK5hylAPdHyGRWT+RLQg
BCKVib2S/Gxqh3Qc9Re6vReKN5icyzYkB0Sv6/kpBLqfx3f7d1WJPUyA+RsCQhBn
crp7rYOBK3vcmRjgrrzCkyNzsTHt6pCfQio3uCru34gCCHZpellZLGzMScVpuQqM
LO9WVJTBe1RSRXej+StutcPR/5sy7yjKrA2y42tAmqKTPgzCdcXsbc2BqQRNZ4X2
UzXAYOMLr2BK43t68DBaX2QGy4AxWqgCqCKpoWwjBEtAD5mh/X+NAbs7kyUov3c=
=JCyB
-----END PGP SIGNATURE-----
Merge tag 'orion_cleanup_for_3.8' of git://git.infradead.org/users/jcooper/linux into next/cleanup
From Jason Cooper:
orion cleanup for v3.8
- remove unused includes in kirkwood
- fix sparse warnings in kirkwood
- checkpatch cleanup in kirkwood
- use common code in pcie on kirkwood
* tag 'orion_cleanup_for_3.8' of git://git.infradead.org/users/jcooper/linux:
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
From Kukjin Kim:
This is adding support for exynos5440, including Quad ARM Cortex-A15
cores and its reference board SSDK5440.
Note, at this moment, just enabled minimal system part for initial kernel
boot and pinctrl driver.
* 'next/soc-exynos5440' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add pin controller node for Samsung EXYNOS5440 SoC
pinctrl: exynos5440: add pinctrl driver for Samsung EXYNOS5440 SoC
ARM: dts: add initial dts file for EXYNOS5440, SSDK5440
ARM: EXYNOS: add support for EXYNOS5440 SoC
Add/add conflict in arch/arm/boot/dts/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
Here is second Samsung DT stuff for v3.8.
This is including power domain DT support for exynos and Google ARM
Chromebook, Snow board and exynos4210-origen updates.
* 'next/dt-samsung-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Use drive strength 3 for SD pins for exynos4
ARM: dts: Set up power domains for exynos4
ARM: EXYNOS: Bind devices to power domains using DT
ARM: EXYNOS: Fix power domain name initialization
ARM: EXYNOS: Detect power domain state on registration from DT
ARM: dts: Add vmmc fixed voltage regulator for exynos4210-origen
ARM: dts: Update sdhci nodes for current bindings for exynos4210-origen
ARM: dts: Update for pinctrl-samsung driver for exynos4210-origen
ARM: dts: Split memory sections for exynos4210-origen
ARM: EXYNOS: add all i2c busses to auxdata for DT
ARM: dts: Add aliases for i2c controller for exynos4
ARM: dts: Add board dts file for Snow board (ARM Chromebook)
ARM: dts: Move the dwmmc aliases from smdk5250 dts to exynos
Add/add conflicts resolved in arch/arm/boot/dts/exynos5250-smdk5250.dts
and arch/arm/mach-exynos/mach-exynos5-dt.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=IZiZ
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-1' of git://git.pengutronix.de/git/imx/linux-2.6 into next/soc
From Sascha Hauer:
ARM i.MX SoC updates for v3.8
* tag 'imx-soc-1' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM i.MX6: remove gate_mask from pllv3
ARM i.MX6: Fix ethernet PLL clocks
ARM i.MX6: rename PLLs according to datasheet
ARM i.MX6: Add pwm support
ARM i.MX51: Add pwm support
ARM i.MX53: Add pwm support
ARM: mx5: Replace clk_register_clkdev with clock DT lookup
Signed-off-by: Olof Johansson <olof@lixom.net>
them as the second mxs/dt pull request for 3.8. Please consider to
pull.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQreEpAAoJEFBXWFqHsHzOem0H/A+agUbLlYNT1Uxc8L6eq0Fg
DkY/BMHoCqlG1+/Yr7nrkTxBWbWTqEfU+DcKyDZrW25CXvNA1WRT3qwfTWC0FxqH
SxXlnyDYa4iHsc63EJVltBoiw3ojN7vhbA41Pp3qGD7h8f+j9RVVxl0HuxwCYsI2
pf141gqFZbB2qiskQUCdfR4E2YKri+SoMXPcLCW+cIyO2UOD1URuAHCPcC/t2vuJ
y1oRvTZCM8UQavfQYG1tpNfUzB79n25vfsL1zTRw8+vp7c9bZzJKbCfWraqfQI8K
ufy21eqNpTAotiknfLySu4JRgiBuv1OL7t5kF7n1jo0w/KV50zRfEIlLGiKtxmA=
=XFM8
-----END PGP SIGNATURE-----
Merge tag 'mxs-dt-3.8-2' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo:
They are a few mxs dts updates coming a little bit late. I'm sending
them as the second mxs/dt pull request for 3.8. Please consider to
pull.
* tag 'mxs-dt-3.8-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: mxs: add oled support for the cfa-10036
ARM: mxs: Add SchulerControl SPS1 DTS file
ARM: imx23-olinuxino: Add spi support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQss0FAAoJEHm+PkMAQRiG6cEH/An3PYsWBBy27tzoLyVfJKF1
3m3vR8HS2tnHg6erxms+738jos59vrWXV0Ygnvw0DHbGR0HNb4rkwce/KXu/jgOD
MRYNYhlhMFJTEUFrSrcwKITrAV3kVPWXxPXgAR6Gzpr6NPKKM9TBzEv0ze56TFYz
asOxqeBcPSS7aFZlkoNsy1wG4l0Quo5ke8VZIxo9Me5qlqubAoZ6pING4wAGXqeE
tf81CevSdpe0nqr8/dlYyCvLjrurgpJQczxRCBI3mP6kLWGfUCVzZmcu86PfT9b+
35zNJwDneIoN+D9bVDHy6mrq9uQdmhWnQuhv1joTPn6RDn1nyBRBd+A5qLxSov4=
=CPoy
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc7' into next/cleanup
Merging in mainline back to next/cleanup since it has collected a few
conflicts between fixes going upstream and some of the cleanup patches.
Git doesn't auto-resolve some of them, and they're mostly noise so let's
take care of it locally.
Conflicts are in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
arch/arm/plat-omap/i2c.c
drivers/video/omap2/dss/dss.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull powerpc EEH bugfixes from Benjamin Herrenschmidt.
Two one-liner fixes for the new EEH code.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/eeh: Do not invalidate PE properly
powerpc/pseries: Fix oops with MSIs when missing EEH PEs
Pull MIPS fixes from Ralf Baechle:
"Three issues fixed accross the field:
- Some functions that were recently outlined as part of a preemption
fix were causing problems with function tracing.
- The recently merged in-kernel MPI library uses very outdated
headers that contain MIPS-specific code which won't build on with
gcc 4.4 or newer.
- The MIPS non-NUMA memory initialization was making only a very
half-baked attempt at merging adjacent memory ranges. This kept
the code simple enough but is now causing issues with kexec."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MPI: Fix compilation on MIPS with GCC 4.4 and newer
MIPS: Fix crash that occurs when function tracing is enabled
MIPS: Merge overlapping bootmem ranges
Merge my own merge branch to get various fixes from there
and upstream, especially the hvc console tty refcouting fixes
which which testing is quite a bit harder...
While the EEH does recovery on the specific PE that has PCI errors,
the PCI devices belonging to the PE will be removed and the PE will
be marked as invalid since we still need the information stored in
the PE. We only invalidate the PE when it doesn't have associated
EEH devices and valid child PEs. However, the code used to check
that is wrong. The patch fixes that.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
The RaidEngine is a new Freescale hardware that used for parity
computation offloading in RAID5/6.
This patch adds the device node in device tree and related binding
documentation.
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Naveen Burmi <naveenburmi@freescale.com>
Signed-off-by: Xuelin Shi <b29237@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PAMU bypass enable register added to the ccsr_guts structure.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
ePAPR v1.1 requires the spin table to be in cached memory. So we need
to change the call argument of ioremap to enable cache and coherence.
We also flush the cache after writing to spin table to keep it compatible
with previous cache-inhibit spin table. Flushing before and after
accessing spin table is recommended by ePAPR.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Power supply for PCI controller ATMU registers is off when system go to
deep-sleep state. So ATMU registers should be re-setup during PCI
controllers resume from sleep.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Function fsl_pcibios_fixup_bus() is available only if PCI is enabled. The
MPC8610 HPCD platform file was not protecting the assigned with an #ifdef,
which results in a link failure when PCI is disabled. Every other platform
already has this #ifdef.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The third argument for of_get_property() is a pointer, hence pass
NULL instead of 0.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Pull x86 arch fixes from Peter Anvin:
"Here is a collection of fixes for 3.7-rc7. This is a superset of
tglx' earlier pull request."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64: Fix ordering of CFI directives and recent ASM_CLAC additions
x86, microcode, AMD: Add support for family 16h processors
x86-32: Export kernel_stack_pointer() for modules
x86-32: Fix invalid stack address while in softirq
x86, efi: Fix processor-specific memcpy() build error
x86: remove dummy long from EFI stub
x86, mm: Correct vmflag test for checking VM_HUGETLB
x86, amd: Disable way access filter on Piledriver CPUs
x86/mce: Do not change worker's running cpu in cmci_rediscover().
x86/ce4100: Fix PCI configuration register access for devices without interrupts
x86/ce4100: Fix reboot by forcing the reboot method to be KBD
x86/ce4100: Fix pm_poweroff
MAINTAINERS: Update email address for Robert Richter
x86, microcode_amd: Change email addresses, MAINTAINERS entry
MAINTAINERS: Change Boris' email address
EDAC: Change Boris' email address
x86, AMD: Change Boris' email address
OpenBlocks A6 has three leds via GPIO. This supports them.
And this fix typo about led, because hardware manual has typo.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
EHCI driver enables by default in kirkwood.dtsi.
This removes kirkwood_ehci_init function.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
OpenBlocks A6 uses second I2C with RTC of s35390a.
This supports them.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Second I2C bus is supported by 88f6282 and 88f6283.
This creates kirkwood-6282.dtsi, and defines DT table
of second I2C bus.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Marvell 98DX412x SoC embed a kirkwood variant that does not have
pinctrl support yet. Even though this kirkwood is very similar to the
88f6281, on the MPP front a lot of pins are not available. That's why a
new kirkwood pinctrl variant is needed.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Make use of the pinctrl driver for configuring all the pins, instead
of using the Orion mpp code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There are a couple of different variants of Kirkwood, which differ in
the pin muxing. These DTSI files set the correct compatibility and
define commonly used groups of pins, which board dbs files can
reference.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Select the generic mvebu kirkwood pincltr driver and generic mvebu
gpio driver. This requires minor changes to the DT, and the calls to
configure plat-orion gpio driver are removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Tested-by: Joshua Coombs <josh.coombs@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
SolidRun CuBox has a led on a gpio pin. As there is now DT pinctrl
support for Dove, make use of a pinhog to ensure the pin is set to
gpio.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Following the ongoing conversion of Orion SoCs to DT, make use of
gpio and pinctrl drivers through DT. The main dtsi for Dove is prepared
to allow board specific descriptors to make use of pinctrl muxing.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Control the power to USB and HDD using a fixed regulator.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Control the power to USB using a fixed regulator.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Josh Coombs <josh.coombs@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Control the power to SATA0 and SATA1 using a fixed regulator.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
A few boards use a GPIO line to enable power to subsystems, eg USB or
SATA devices. Pull in the regulator framework as the first step to
controlling these GPIO lines are regulators.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Also enable the gpio-poweroff driver when DT is used.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The default chip-delay of 25us is a bit too tight for some DNS-320's,
and D-Link seem to specify 30us in their kernels for both devices.
Increase to 35us to make sure the NAND is stable.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the EHCI driver has DT support, drop old style configuration
of it and add DT in its place. Since all the boards enable the EHCI,
enable it by default in kirkwood.dtsi. Any new boards which don't have
USB can specifically disable it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Run Time Average Power Limiting interface
is currently model specific, present on Sandy Bridge
and Ivy Bridge processors.
These #defines correspond to documentation in the latest
"Intel® 64 and IA-32 Architectures Software Developer Manual",
plus some typos in that document corrected.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
Now that turbostat is built in the kernel tree,
it can share MSR #defines with the kernel.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
Simple build regression fix for DT device drivers on Sparc. An earlier
change had masked out the of_iomap() helper on SPARC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yKFc
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull device tree regression fix from Grant Likely:
"Simple build regression fix for DT device drivers on Sparc. An
earlier change had masked out the of_iomap() helper on SPARC."
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6:
of/address: sparc: Declare of_iomap as an extern function for sparc again
This bug-fix makes sure that of_iomap is defined extern for sparc so that the
sparc-specific implementation of_iomap is once again used when including
include/linux/of_address.h in a sparc context. OF_GPIO that is now available for
sparc relies on this.
The bug was inadvertently introduced in a850a75, "of/address: add empty static
inlines for !CONFIG_OF", that added a static dummy inline for of_iomap when
!CONFIG_OF_ADDRESS. However, CONFIG_OF_ADDRESS is never defined for sparc, but
there is a sparc-specific implementation /arch/sparc/kernel/of_device_common.c.
This fix takes the same approach as 0bce04b that solved the equivalent problem
for of_address_to_resource.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull i2c fixes from Wolfram Sang:
"Bugfixes for the i2c subsystem.
Except for a few one-liners, there is mainly one revert because of an
overlooked dependency. Since there is no linux-next at the moment, I
did some extra testing, and all was fine for me."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Fix code to free gpios
i2c: omap: ensure writes to dev->buf_len are ordered
Revert "ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints"
i2c: at91: fix SMBus quick command
Pull sparc fix from David Miller:
"Bug fix from Al Viro"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: not any error from do_sigaltstack() should fail rt_sigreturn()
I missed one pull request from Samsung with one fix in the previous
batch. Here it is -- a dma driver fix for an early version of silicon
that they still support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bSmr
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull one more ARM SoC fix from Olof Johansson:
"I missed one pull request from Samsung with one fix in the previous
batch. Here it is -- a dma driver fix for an early version of silicon
that they still support."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: PL330 MDMA1 fix for revision 0 of Exynos4210 SOC
There's no reason to mark compat_get_sigframe inline explicitly, so
remove the annotation and let the compiler decide what's best.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We only have one type of frame (rt_sigframe) for arm64, so just return
that type directly and dispense with the framesize argument, which is
presumably a hangover from code copied from arch/arm/.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
setup_return is a void function, so make compat_setup_return look the
same rather then unconditionally return 0.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
To allow debuggers to unwind through signal frames, we create a fake
stack unwinding prologue containing the link register and frame pointer
of the interrupted context. The signal frame is then offset by 16 bytes
to make room for the two saved registers which are pushed onto the frame
of the *interrupted* context, rather than placed directly above the
signal stack.
This doesn't work when an alternative signal stack is set up for a SEGV
handler, which is raised in response to RLIMIT_STACK being reached. In
this case, we try to push the unwinding prologue onto the full stack and
subsequently take a fault which we fail to resolve, causing setup_return
to return -EFAULT and handle_signal to force_sigsegv on the current task.
This patch fixes the problem by including the unwinding prologue as part
of the rt_sigframe definition, which is populated during setup_sigframe,
ensuring that it always ends up on the signal stack.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
This patch updates the arm64 asm/Kbuild file to include the clkdev.h
generic header.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Viresh Kumar <Viresh.kumar@linaro.org>
A recent patch changed some irq routines from inlines to functions.
These routines are called by the tracer code. Now that they're functions,
if they are compiled for function tracing they will call the tracer
and crash the system due to infinite recursion. The fix disables
tracing in these functions by using "notrace" in the function
definition.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: David Daney <david.daney@cavium.com>
Pathchwork: https://patchwork.linux-mips.org/patch/4564/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Without this, we may end up with something like this in /proc/iomem:
01100000-014fffff : System RAM
01100000-013bf48f : Kernel code
013bf490-0149e01f : Kernel data
01500000-0c0fffff : System RAM
but the two System RAM ranges should be one single range. This particular
case will result in kexec failure on Octeon systems if the kernel being
loaded by kexec is bigger than the already running kernel.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pulling in a newer version of the depend branch from the gpio tree,
since there was some randconfig breakage introduced at the version we
had, and we want to keep those things as bisectable as possible. It's
not bad enough to warrant a rebase though, so there'll be a window of
exposure to this.
* depends/gpio-devel:
gpio: SPEAr: add spi chipselect control driver
gpio: gpio-max710x: Support device tree probing
gpio: twl4030: Use only TWL4030_MODULE_LED for LED configuration
gpio: tegra: read output value when gpio is set in direction_out
gpio: pca953x: Add compatible strings to gpio-pca953x driver
gpio: pca953x: Register an IRQ domain
gpio: mvebu: Set free callback for gpio_chip
gpio: tegra: Drop exporting static functions
gpio: tegra: Staticize non-exported symbols
gpio: tegra: fix suspend/resume apis
gpio-pch: Set parent dev for gpio chip
gpio: em: Fix build errors
Signed-off-by: Olof Johansson <olof@lixom.net>
Modern GCC can generate code which makes use of the CPU's native
unaligned memory access capabilities. This is useful for the C
decompressor implementations used for unpacking compressed kernels.
This patch disables alignment faults and enables the v6 unaligned
access model on CPUs which support these features (i.e., v6 and
later), allowing full unaligned access support for C code in the
decompressor.
The decompressor C code must not be built to assume that unaligned
access works if support for v5 or older platforms is included in
the kernel.
For correct code generation, C decompressor code must always use
the get_unaligned and put_unaligned accessors when dealing with
unaligned pointers, regardless of this patch.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a kernel is configured with a DT containing more /cpu nodes than
nr_cpu_ids, the number of cpus must be capped in the DT parsing
code. Current code carries out the check, but fails to cap the
value and the check is executed after the cpu logical index is used,
which can lead to memory corruption due to index overflow.
This patch refactors the check against nr_cpu_ids and move it before
any computed index is used in the parsing code.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit e50c541 (ARM: perf: add guest vs host discrimination) broken the
link as perf_instruction_pointer and perf_misc_flags are not defined
when CONFIG_HW_PERF_EVENTS is not selected.
As it make little sense to try and profile a guest without any HW event,
just fallback to the original code when this config option is not selected.
Reported-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow drivers to enable/disable ccwgroup devices.
Acked-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
I was chasing down a bug of random validity intercepts on s390.
(guest prefix page not mapped in the host virtual aspace). Turns out
that the problem was a wrong address space control element. The
cause was quite complex:
During paging activity a DAT protection during SIE caused a program
interrupt. Normally, the sie retry loop tries to catch all
interrupts during and shortly before sie to rerun the setup. The
problem is now that protection causes a suppressing program interrupt,
causing the PSW to point to the instruction AFTER SIE in case of DAT
protection. This confused the logic of the retry loop to not trigger,
instead we jumped directly back to SIE after return from
the program interrupt. (the protection fault handler itself did
a rewind of the psw). This usually works quite well, but:
If now the protection fault handler has to wait, another program
might be scheduled in. Later on the sie process will be schedules
in again. In that case the content of CR1 (primary address space)
will be wrong because switch_to will put the user space ASCE into CR1
and not the guest ASCE.
In addition the program parameter is also wrong for every protection
fault of a guest, since we dont issue the SPP instruction.
So lets also check for PSW == instruction after SIE in the program
check handler. Instead of expensively checking all program
interruption codes that might be suppressing we assume that a program
interrupt pointing after SIE was always a program interrupt in SIE.
(Otherwise we have a kernel bug anyway).
We also have to compensate the rewinding, since the C-level handlers
will do that. Therefore we need to add a nop with the same length
as SIE before the sie_loop.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: stable@vger.kernel.org
CC: Heiko Carstens <heiko.carstens@de.ibm.com>
The current single step code is racy in regard to concurrent delivery
of signals. If a signal is delivered after a PER program check occurred
but before the TIF_PER_TRAP bit has been checked in entry[64].S the code
clears TIF_PER_TRAP and then calls do_signal. This is wrong, if the
instruction completed (or has been suppressed) a SIGTRAP should be
delivered to the debugger in any case. Only if the instruction has been
nullified the SIGTRAP may not be send.
The new logic always sets TIF_PER_TRAP if the program check indicates PER
tracing but removes it again for all program checks that are nullifying.
The effect is that for each change in the PSW address we now get a
single SIGTRAP.
Reported-by: Andreas Arnez <arnez@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow to generate code that only runs on zEC12 machines.
Also add a check which prevents the kernel to run on machines which
do not have any of the following new facilities installed:
- (48) decimal-floating-point zoned-conversion
- (49) execution-hint
- (49) load-and-trap
- (49) miscellaneous-instruction-extensions
- (49) processor-assist
- (50) constrained transactional-execution
- (73) transactional-execution
48, 49, 50 and 73 are the bit numbers of the facility indications for
each of the required facilities.
Note that we assume that user-space gets compiled with the same
compiler options, therefore we also test for a dfp facility even
if the kernel doesn't make use of it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Mainly merge all different per-cpu arrays into a single array which
holds all topology information per logical cpu.
Also fix the broken core vs socket variable naming and simplify the
locking a bit.
When running in environments without topology information also
invent book, socket and core ids, so that not all ids are zero.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Keep related functions together and move to appropriate file.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move and rename init_storage_keys() to pageattr.c, so it can also be
used from the sclp memory hotplug code in order to initialize
storage keys.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Just convert fault_init() to an early initcall. That's still early
enough since it only needs be called before user space processes get
executed. No reason to externalize it.
Also add the function to the init section and move the store_indication
variable to the read_mostly section.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let the dasd driver and qdio use ccw_device_get_schid and
get rid of other similar functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This will be needed by the new virtio-ccw transport.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the BUG_ON's that check for failure or incomplete
results of the s390 hardware crypto instructions.
Rather report the errors as -EIO to the crypto layer.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Preinitialize the program check table, so we can put it into the
read-only data section.
Also use only four byte entries for the table, since each program
check handler resides within the first 2GB. Therefore this reduces
the size of the table by 50% on 64 bit builds.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use 1MB frames for vmemmap if EDAT1 is available in order to
reduce TLB pressure
Always use a 1MB frame even if its only partially needed for
struct pages. Otherwise we would end up with a mix of large
frame and page mappings, because vmemmap_populate gets called
for each section (256MB -> 3.5MB memmap) separately.
Worst case is that we would waste 512KB.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use 2GB frames for indentity mapping if EDAT2 is
available to reduce TLB pressure.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull input updates from Dmitry Torokhov:
"This fixes recent regression where /dev/input/mice got assigned wrong
device node which messed up setups with static /dev, and a regression
in ads7846 GPIO debounce setup."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
ARM - OMAP: ads7846: fix pendown debounce setting
Input: ads7846 - enable pendown GPIO debounce time setting
Input: mousedev - move /dev/input/mice to the correct minor
Input: MT - document new 'flags' argument of input_mt_init_slots()
From Kukjin Kim:
Here is Samsung fixes for v3.7 and it is for fixing of mdma1 address
for exynos4210 rev0 SoC.
* 'v3.7-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: PL330 MDMA1 fix for revision 0 of Exynos4210 SOC
Signed-off-by: Olof Johansson <olof@lixom.net>
The new EEH code introduced a small regression, if the EEH PEs
are missin (which happens currently in qemu for example), it
will deref a NULL pointer in the MSI code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A few more fixes for final 3.7. Two dealing with pinmux setup on OMAP, and
one dealing with TV output on DaVinci. And one small MAINTAINER update.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=FhMC
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few more fixes for final 3.7. Two dealing with pinmux setup on
OMAP, and one dealing with TV output on DaVinci. And one small
MAINTAINER update."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: davinci: dm644x: fix out range signal for ED
ARM: OMAP4: TWL: mux sys_drm_msecure as output for PMIC
ARM: OMAP3: igep0020: Set WIFI/BT GPIO pins in correct mux mode
ARM: OMAP: Add maintainer entry for IGEP machines
This is two bug fixes: one fixes a loophole where rt_sigprocmask() with the
wrong values panics the box (Denial of Service) and the other fixes an
aliasing problem with get_shared_area() which could cause data corruption.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQrfisAAoJEDeqqVYsXL0MabcIALeL/hMtLSdwo01AG47Z6v6u
jNuQIE6v3mvsaoJ5zxhM570/SZc+waDojfNpax+RjJc4vppDHq40xhI19RHczCvo
AIASYIZynMHF1kqXsFpWfDtOGUzRtFjn8g60rfX593ghtpuliTXm+WgYCl43SyYm
Ee1rLAFrEiXKAHyTO+QXi/EiTHPDGxw84fZdypIC7Bxi0JZg7SX5g/KXwGC2JT7M
fRW2SmrfgFOLMvmYYbyk4BWvZ4dneikcUhOJGiLcpSy++MJF6ccjbfiCD4i6gD9e
cM57jLnHnV2U+qp4e2Rcosi9AQwfSYRkr7j37/OT0KoCLmSRZbwqpF1RMjMKyGM=
=ckHH
-----END PGP SIGNATURE-----
Merge tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
Pull PARISC fixes from James Bottomley:
"This is two bug fixes: one fixes a loophole where rt_sigprocmask()
with the wrong values panics the box (Denial of Service) and the other
fixes an aliasing problem with get_shared_area() which could cause
data corruption.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] fix user-triggerable panic on parisc
[PARISC] fix virtual aliasing issue in get_shared_area()
The armada_cfg_base() function returns the base address of the
registers that allow to configure the decoding for a particular
address window. On Armada 370/XP, the lower windows have more
configuration registers (4 registers) than the higher windows (2
registers). This armada_cfg_base() takes this into account by doing a
different offset calculation depending on the window number, but this
offset calculation was wrong for the higher windows.
Even though we were not using high window numbers until now (only
window 0 is used to map the BootROM, needed for SMP), we use this
function at boot time to disable all windows to ensure that nothing
remains intialized from what the bootloader has done.
Unfortunately, the U-Boot on the OpenBlocks AX3-4 uses a window with a
high number (above 8) to remap the BootROM. And then when the kernel
boots, it remaps the BootROM in window 0. Normally, this is not a
problem, because all windows have previously been disabled. Except
that due to our wrong offset calculation, the windows with high
numbers were not properly disabled, leading to the BootROM being
mapped twice. The visible result of this bug was that the kernel was
unable to get the second CPU started on the OpenBlocks AX3-4
platform. With this fix, all windows are properly cleared at boot
time, the BootROM is remapped only once in window 0, and the second
CPU boots fine.
Thanks a lot to Lior Amsamlen <alior@marvell.com> for his help in
debugging this problem.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
Strictly speaking, this bug was introduced in 3.7, but since the only
platforms supported in 3.7 were Armada 370 and Armada XP, and there
was anyway no SMP support at this time, it isn't really worth the
effort to push this patch in 3.7.
Now that the additional enable bits in the enet PLL are handled
as gates, the gate_mask is identical for all plls. Remove the
gate_mask from the code and use the BM_PLL_ENABLE bit for
enabling/disabling the PLL.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
In current code the ethernet PLL is not handled correctly. The PLL runs at 500MHz
and has different outputs. Only the enet reference clock is implemented. This
patch changes the PLL so that it outputs 500MHz and adds the additional outputs
as dividers. This now matches the datasheet which says:
> This PLL synthesizes a low jitter clock from 24 MHz reference clock.
> The PLL outputs a 500 MHz clock. The reference clocks generated by this PLL are:
> • Ref_PCIe = 125 MHz
> • Ref_SATA = 100 MHz
> • Ref_ethernet, which is configurable based on the PLL_ENET[1:0] register field.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
In recent reference manuals the PLLs were renumbered. PLL8 now is
PLL6 and vice versa. Change the code according to the reference
manual to avoid confusion.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Set "y_skip_top" to zero and revise comment as I do not see this line
corruption on two different mt9v022 setups. The first read-out line
is perfectly fine. Add mt9v022 platform data configuring y_skip_top
for platforms that have issues with the first read-out line. Set
y_skip_top to 1 for pcm990 board.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The purpose of this series is to add the SMP support for the Armada XP
SoCs. Beside the SMP support itself brought by the last 3 commits,
this series also adds the support for the coherency fabric unit and
the power management service unit.
The coherency fabric is responsible for ensuring hardware coherency
between all CPUs and between CPUs and I/O masters. This unit is also
available for Armada 370 and will be used in an incoming patch set
for hardware I/O cache coherency.
The power management service unit is responsible for powering down and
waking up CPUs and other SOC units.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCs+5oACgkQCwYYjhRyO9UywACfVp3WPDHLxE8ypew3AWoTyxe3
JcMAoIjojnjWCd44cqDJ4uEpvi6KNquE
=BR8m
-----END PGP SIGNATURE-----
Merge tag 'marvell-armadaxp-smp-for-3.8' of github.com:MISL-EBU-System-SW/mainline-public into mevbu-dt-additions
SMP support for Armada XP
The purpose of this series is to add the SMP support for the Armada XP
SoCs. Beside the SMP support itself brought by the last 3 commits,
this series also adds the support for the coherency fabric unit and
the power management service unit.
The coherency fabric is responsible for ensuring hardware coherency
between all CPUs and between CPUs and I/O masters. This unit is also
available for Armada 370 and will be used in an incoming patch set
for hardware I/O cache coherency.
The power management service unit is responsible for powering down and
waking up CPUs and other SOC units.
Conflicts:
arch/arm/mach-mvebu/armada-370-xp.c
Mark Brown