When controller lockup condition is detected,
we should fail all outstanding commands and disable
the controller. This will enable multipath solutions
to recover gracefully.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We weren't filling in the transfer length of the
flush cache command (it transfers 4 bytes of zeroes).
Firmware didn't seem to be bothered by this, but it
should be fixed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The currentsd[] array in hpsa_update_scsi_devices had room for
256 devices. The code was iterating over however many physical
and logical devices plus an additional number of possible external
MSA2XXX controllers, which together could potentially exceed 256.
We increased the size of the currentsd array to 1024 + 1024 + 32 + 1
elements to reflect a reasonable maximum possible number of devices
which might be encountered. We also don't just walk off the end
of the array if the array controller reports more devices than we
are prepared to handle, we just ignore the excessive devices.
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Rename HPSA_MAX_SCSI_DEVS_PER_HBA to HPSA_MAX_DEVICES
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Set the max hardware sectors in the SCSI host template to 8192
to allow for larger i/o's (8192 is the same limit the cciss
driver currently has.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During heavy I/O (CPU-affinity mode enabled) and CLI/Agent
interactions, the driver would report periodic mailbox command
timeout statuses. Within the CPU-affinity ISR handler, the
driver should check the 'disable-msix-handshake' flag in deciding
whether or not to clear HCCRX_CLR_RISC_INT. The mode is not
specific to a dedicated queue, instead, applies to the current
'ha' context.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When SRR LS_ACC is dropped, the driver was not issuing ABTS for SRR when it
times out. Since the target received SRR, it was able to send the XFER_RDY and
the the original IO request completed successfully. In this condition ABTS was
not sent during bnx2fc_srr_compl(). Fix this by first checking for ELS timeout
and issue ABTS before checking if original IO request is complete.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the IO and the corresponding ABTS are not responded by a target, cleanup the
IO and issue explicit logout when ulp timer expires while waiting for ABTS to
complete. Wait for the session to be ready before returning to the SCSI layer.
If the session is not ready let the SCSI-ml escalate the error recovery.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The call to complete() in st_scsi_execute_end() wakes up sleeping thread
in write_behind_check(), which frees the st_request, thus invalidating
the pointer to the associated bio structure, which is then passed to the
blk_rq_unmap_user(). Fix by storing pointer to bio structure into
temporary local variable.
This bug is present since at least linux-2.6.32.
CC: stable@kernel.org
Signed-off-by: Petr Uzel <petr.uzel@suse.cz>
Reported-by: Juergen Groß <juergen.gross@ts.fujitsu.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make sure that SCSI device removal via scsi_remove_host() does finish
all pending SCSI commands. Currently that's not the case and hence
removal of a SCSI host during I/O can cause a deadlock. See also
"blkdev_issue_discard() hangs forever if underlying storage device is
removed" (http://bugzilla.kernel.org/show_bug.cgi?id=40472). See also
http://lkml.org/lkml/2011/8/27/6.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: <stable@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There is no reason to limit the SCSI disk namespace to sdXXX.
Add new error messages to sd_probe() in the unlikely event that either
ida_get_new() or sd_format_disk_name() fail.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The driver was setting the action to MPI2_CONFIG_ACTION_PAGE_READ_CURRENT,
which only returns active volumes. In order to get info on inactive volumes,
the driver needs to change the action to
MPI2_RAID_PGAD_FORM_GET_NEXT_CONFIGNUM, and traverse each config till the
iocstatus is MPI2_IOCSTATUS_CONFIG_INVALID_PAGE returned.
Added a change in the driver to remove the instance of
sas_device object when the driver returns "1" from the slave_configure callback.
Also fixed code to report the hot spares to the operating system with a /dev/sg
assigned.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is due to the slave_configuration routine is getting called when
host reset is active, and config page reads are failing, and driver
attempts to added device with stale config data.
To fix the issue, added error checking in slave_configure to check
for configuration pages failing, and return "1" so the device is
not configured. The config pages are failing if raid volume is
configured while issuing a host reset, thus driver is reading stale
data and proceeding to attempt to add. The fix is to return error
so the volume is not configured.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is due to driver reporting a device missing to the OS then the OS sending
a SYNC_CACHE request to driver while the IO queues are locked due to host reset.
To fix the issue, the driver will be waking up the port enable context
immediately when the driver receives the reply message, instead of waiting
on the hot plug worker threads.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix for dead lock occurring between host_lock and sas_device_lock.
The deadlock is between two spin locks, between the shost->host_lock
and driver ioc->sas_device_lock.
The fix is to rearrange the code in the FW/Driver device removal
handshake so the ioc->sas_device_lock is not occurring when the
shost->host_lock is taken.
[jejb: zero initialise sas_address to fix spurious compiler warning]
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The fix is in the driver-firmware handshake device removal code. We
need to read the controller ioc_state to see if controller is OPERATIONAL
prior to sending target reset and OP_REMOVE. Previously it was checking
the flag ioc->shost_recovery flag, which is always set when host reset is
active, thus preventing drives from getting properly deleted.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The fix is to inhibit the warning message in _scsih_get_sas_address
when the MPI2_IOCSTATUS_CONFIG_INVALID_PAGE ioc status is returned.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix for issue : While discovery is in progress, hot unplug and hot plug of
enclosure connected to the controller card is causing system to hang.
When a device is in the process of being detected at driver load time then
if it is removed, the device that is no longer present will not be added
to the list. So the code in _scsih_probe_sas() is rearranged as such so
the devices that failed to be detected are not added to the list.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
New feature Fast Load Support.
(1)Asynchronous SCSI scanning: This will allow the drivers to scan
for devices in parallel while other device drivers are loading at
the same time. This will improve the amount of time it takes for the
OS to load.
(2) Reporting Devices while port enable is active: This feature will
allow devices to be reported to OS immediately while port enable is
active. The previous implementation waits for port enable to complete,
and then report devices. This feature is only enabled on IT firmware
configurations when there are no boot device configured in BIOS Configuration
Utility, else the driver will wait till port enable completes reporting
devices. For IR firmware, this feature is turned off. This feature is to
address large SAS topologies (>100 drives) when the boot OS is using onboard
SATA device, in other words, the boot devices is not
connected to our controller.
(3) Scanning for devices after diagnostic reset completes: A new routine
_scsih_scan_start is added. This will scan the expander pages, IR pages,
and sas device pages, then reporting new devices to SCSI Mid layer. It
seems the driver is not supporting adding devices while diagnostic reset
is active. Apparently this is due to the sanity checks on
ioc->shost_recovery flag throughout the context of kernel work thread FIFO,
and the mpt2sas_fw_work.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
1)Added ProxyVF_ID field to Configuration Request message.
2)Added IO Unit Page 8, IO Unit Page 9,and IO Unit Page 10.
3)Added SASNotifyPrimitiveMasks field to IOC Page 7.
4)Added SAS NOTIFY Primitive event.
5)Added Temperature Threshold Event.
6)Added Host Message Event.
7)Added Send Host Message request and reply.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* 'for-linus' of git://git.open-osd.org/linux-open-osd: (21 commits)
ore: Enable RAID5 mounts
exofs: Support for RAID5 read-4-write interface.
ore: RAID5 Write
ore: RAID5 read
fs/Makefile: Always inspect exofs/
ore: Make ore_calc_stripe_info EXPORT_SYMBOL
ore/exofs: Change ore_check_io API
ore/exofs: Define new ore_verify_layout
ore: Support for partial component table
ore: Support for short read/writes
exofs: Support for short read/writes
ore: Remove check for ios->kern_buff in _prepare_for_striping to later
ore: cleanup: Embed an ore_striping_info inside ore_io_state
ore: Only IO one group at a time (API change)
ore/exofs: Change the type of the devices array (API change)
ore: Make ore_striping_info and ore_calc_stripe_info public
exofs: Remove unused data_map member from exofs_sb_info
exofs: Rename struct ore_components comps => oc
exofs/super.c: local functions should be static
exofs/ore.c: local functions should be static
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
dp83640: free packet queues on remove
dp83640: use proper function to free transmit time stamping packets
ipv6: Do not use routes from locally generated RAs
|PATCH net-next] tg3: add tx_dropped counter
be2net: don't create multiple RX/TX rings in multi channel mode
be2net: don't create multiple TXQs in BE2
be2net: refactor VF setup/teardown code into be_vf_setup/clear()
be2net: add vlan/rx-mode/flow-control config to be_setup()
net_sched: cls_flow: use skb_header_pointer()
ipv4: avoid useless call of the function check_peer_pmtu
TCP: remove TCP_DEBUG
net: Fix driver name for mdio-gpio.c
ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
ipv4: fix ipsec forward performance regression
jme: fix irq storm after suspend/resume
route: fix ICMP redirect validation
net: hold sock reference while processing tx timestamps
tcp: md5: add more const attributes
Add ethtool -g support to virtio_net
...
Fix up conflicts in:
- drivers/net/Kconfig:
The split-up generated a trivial conflict with removal of a
stale reference to Documentation/networking/net-modules.txt.
Remove it from the new location instead.
- fs/sysfs/dir.c:
Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
with Eric Biederman's changes for tagged directories.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: Karen Xie <kxie@chelsio.com>
Cc: linux-scsi@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The P600 requires a small delay when changing states. Otherwise we may think
the board did not reset and we bail. This for kdump only and is particular
to the P600.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Udev uses the connection's persistent address/port in the
/dev/disk/by-path name. qla4xxx is not exporting this value
so its iscsi disk names have been lacking the iscsi info.
In the old driver we did not have this information but
we do now and can fix this by just setting the flags to tell
libiscsi/scsi_transport_iscsi to export this info in sysfs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If an adapter dump times out, the ipr driver will abort the
dump and proceed to reset and recover the adapter. When an
adapter dump completes, the work thread which is reading the
adapter dump will initiate an adapter reset to recover the
adapter. However, when the adapter dump gets aborted, the
work thread should not initiate an adapter reset, since an
adapter reset is already in progress. This fixes a case of
calling pci_block_user_cfg_access overlapped, which results
in a BUG.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas will fix a potential bad pointer access
in megasas_reset_timer(), when a MegaRAID 9265/9285 or 9360/9380 gets a
timeout. megasas_build_io_fusion() sets SCp.ptr to be a struct
megasas_cmd_fusion *, but then megasas_reset_timer() was casting SCp.ptr to be
a struct megasas_cmd *, then trying to access cmd->instance, which is invalid.
Just loading instance from scmd->device->host->hostdata in
megasas_reset_timer() fixes the issue.
Signed-off-by: Adam Radford <aradford@gmail.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following warning message may be confusing to some users:
dev_warn(&pdev->dev, "Controller claims that "
"'Bit 2 doorbell reset' is "
"supported, but not 'bit 5 doorbell reset'. "
"Firmware update is recommended.\n");
Most users don't know or care what bit we may be hitting. Also change
"recommended" to "required."
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Userspace was sending the priority/id part of the vlan tag
and sysfs was displaying the id in the vlan file. This
renames the vlan sysfs file to vlan_id to reflect that it
was showing the id and to match the vlan_priority file.
This also adds a ISCSI_NET_PARAM_VLAN_TAG iscsi nl command
to relfect that we are sending down the vlan/priority
part of the tag.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This has the driver use helpers for a common operation and fixes
a issue where if multiple iscsi params are sent they could be
sent at offsets that cause unaligned accesses. The nla helpers
account for the padding needed to align properly for the driver.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use the same format for link local variables. Instead
of linklocal do link_local.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Replaced the iscsi_get_next_target_id with IDA to make
target-id allocation efficient for iscsi offload drivers
This patch should be applied after Jonathen Cameron Patch
"ida : simplified functions for id allocation"
Signed-off-by: John Soni Jose <jose0here@gmail.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is just a cleanup, to silence static checker warnings. It
doesn't change how the code works.
buf[] can either be BUF_SIZE if this is called from sysfs, or it can
be 16 if it's called from aac_get_adapter_info() via
aac_get_serial_number(). We use the smaller limit here.
sizeof(dev->supplement_adapter_info.MfgPcbaSerialNo) is 12 so there
is actually no chance of hitting either limit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Achim Leubner <Achim_Leubner@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change driver version to 8.3.27
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix queue allocation failure recovery
- Move the allocation of the Queues closer to the creation of the queues.
- If there is a problem with creation, or if the HBA is reset, the queues
will be completely freed and re allocated.
- Only allocate fcp_eq_hdl if cfg_fcp_eq_count is non-zero.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implemented new algorithm for getting physical port name for all SLI4 devices
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Changed the timeout value for flash-based SLI_CONFIG (0x9B)
mailbox command to 300 seconds for worst case flash delays.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Miscellanous logic and interface fixes
- Fix lpfc_init_vfi_cmpl to check the interface type for interface type 0
before parsing the results.
- Cast uint32_t values that are multiplied to uint64_t before the
multiplication.
- Instead of "break" statement when PCI read returned error, use the goto
statement to the end of the routine after setting return value
- moved the msleep(10) to the beginning of the wait loop for checking the
SLIPort_Status register
- Added the code to follow the existing wait for SLIPort_Status register RDY,
ERR, and RN bits to be set by the port before proceeding to perform PCI
function reset.
- Do not override ulpCt_h and ulpCt_l for SLI 4 ports.
- For vport delete, call lpfc_nlp_put when the vport's vpi state is not
marked with VPI_REGISTERED.
- Added missed fields into the driver's Controller Attributes Structure
- Changed ringing EQ/CQ/RQ doorbell register to be dependent on the size
of the queue.
- Return -EACCES in issue_reset if cfg_enable_hba_reset is zero.
- Added new logging flag LOG_FCP_UNDER 0x00040000 to qualify underrun logging.
- Add a check in the fabric name display routine to display 0 if the port
state is <= FLOGI.
- Add a check to the switch statement in lpfc_decode_firmware_rev to check
for an 'X'.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas updates the
ChangeLog.megaraid_sas file and updates the driver version.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas adds a driver workaround for
PERC5/1068 based controller FW that keeps a command from the main
kernel that the driver cannot cancel which was causing a kernel panic
in shutdown of the kdump kernel.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When sendtargets response is greater then max receive data segment length,
the passthrough IOCB failed with data overrun status. Solution is to
allocate space for iSCSI header in the IOCB response buffer.
JIRA Key: UPSISCSI-147
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When iscsid restarted for an existing active session, set DDB will
fail with status already logged in. In this case, we have to send
logged in event to iscsid.
JIRA Key: OPENISCSI-21
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Devices are getting blocked during continuous link up and down.
Solution is, during relogin unblock the session, using iscsi_conn_start,
before sending connection logged in event.
JIRA Key: UPSISCSI-138
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During link down, iscsid tries to do re-login to failed session. In case of
link down-up-down, LLD was sending connection login failed event to iscsid,
which is destroying the session, instead we have to continue re-login by
sending connection err event.
JIRA Key: UPSISCSI-134
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Unable to login to session if login-logout issued consecutively for
multiple sessions. Solution is to clear idx in DDB map on the basis
of no-active connection asynchronous event (AEN).
JIRA Key: UPSISCSI-135
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Firmware reserves DDBs if there are entries in the FLASH.
So there are no free DDBs left when a iSCSI login is initiated
by user space tool like iscsiadm.
Since now login is not controlled by firmware, LLD need to free
up the DDBs after firmware init. This will ensure free DDBs are
available for iSCSI logins using iscsiadm.
JIRA Key: UPSISCSI-151
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If a boot target has a BIDI CHAP enabled, then read the user/secret from
CHAP table. Do not assume BIDI chap at peer CHAP index + 1
JIRA Key: UPSISCSI-156
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The driver failed to export primary boot target if secondary target did not
exist in the FLASH. If boot targets are not valid then driver assumed 0 and
1 as default boot targets. Since these target did not exist in flash, the
driver failed exporting all the targets.
JIRA Key: UPSISCSI-148
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
QLogic applications store the CHAP information in FLASH. During login,
authentication information is provided using an index into the CHAP region.
In order to support QLogic applications along with iscsiadm, updated the
LLD to not add duplicate CHAP entries in the CHAP region and preserve the
existing CHAP info in the CHAP region in FLASH.
This allows QLogic applications to pre-write the CHAP entries in the
CHAP region.
With iscsiadm, when the CHAP authentication information is sent to the LLD, the
LLD searches for the entry in CHAP region in FLASH, if exists then do not add.
If CHAP entry does not exist then add the CHAP entry in the CHAP region.
JIRA Key: UPSISCSI-146
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver was not setting the bidirectional CHAP bit correctly in
the DDB entry.
JIRA Key: UPSISCSI-108
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes a situation when wrb was not being memset to zero
before being used
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes a bug where the task->sc was cleaned up earlier on a
different thread, possibly abort, and the completion comes later.
This was causing a crash which has been reported in multiple places
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes wrong dmsg setting when we send out wrb.
If the ttt is not ISCSI_RESERVED_TAG then we should be setting
dmsg=1 so that the completion is done without waiting for a
iscsi level response from the target
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes the Kdump failure reported by Redhat wich was caused by
be2iscsi resetting the Chip when be2iscsi detects it is in crashdump mode. If
be2net was loaded before be2iscsi then this leaves be2net driver hanging on to
resources that the chip stopped recognising after the reset.
This patch replaces chip reset with Function reset so that only the
particular function and not the whole chip is affected
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
qlogicpti times out for some tape library operations (like mtx
inventory). It seems SCSI command timeout is hardcoded into the driver.
Fix it by propagating the timeout from scsi request to the controller as
suggested by James Bottomley.
Tested on Sun Ultra 1 with Sun StorEdge L8 Autoloader.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds one more check-condition for scsi_dh_alua handler. Without
this, the handler attach fails sometimes during the discovery. I have noticed
this with NetApp E-Series storage with alua mode. Also removed some
unnecessary brackets {} for consistency.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The write buffer command is used to download and burn new IOA FW images.
The same interface can now be used to flash FPGA and flash back DRAM images.
To download and flash the new images takes more than 15 minutes, so increase
the write buffer command timeout to 30 minutes.
The FPGA and flash back DRAM images don't have the same card_type as the IOA FW
image. So, remove the sanity checking from the driver. The adapter has sanity
checking and will only accept a valid image.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
port->dev_list maintains a list of devices attached to a given sas root port.
It needs to be mutated under a lock as contexts outside of the
single-threaded-libsas-workqueue access the list via sas_find_dev_by_rphy().
Fixup locations where the list was being mutated without a lock.
This is a follow-up to commit 5911e963 "[SCSI] libsas: remove expander
from dev list on error", where Luben noted [1]:
> 2/ We have unlocked list manipulations in sas_ex_discover_end_dev(),
> sas_unregister_common_dev(), and sas_ex_discover_end_dev()
Yes, I can see that and that is very unfortunate.
[1]: http://marc.info/?l=linux-scsi&m=131480962006471&w=2
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support for get_lesb so that the valid statistics are returned by the
remote peer when RLS command is issued.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Except for obtaining the netdev from lport, fcoe_get_lesb is the common code
for the LLDs.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Link may not be up when the driver receives ulp_start event, and hence
fcoe_ctlr_link_up is not called. Call fcoe_ctlr_link_up during
indicate_netevent only when the interface is enabled. (It has to be called when
enabled because that is an indication that the vlan discovery is completed).
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow the sas-transport-class to update events for local phys via a new
PHY_FUNC_GET_EVENTS command to ->lldd_control_phy(). Fixup drivers that
are not prepared for new enum phy_func values, and unify
->lldd_control_phy() error codes.
These are the SAS defined phy events that are reported in a
smp-report-phy-error-log command:
* /sys/class/sas_phy/<phyX>/invalid_dword_count
* /sys/class/sas_phy/<phyX>/running_disparity_error_count
* /sys/class/sas_phy/<phyX>/loss_of_dword_sync_count
* /sys/class/sas_phy/<phyX>/phy_reset_problem_count
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixes a bug where any phy removed from the port set the port
state to "stopping" - do this only when the last phy removed
from the port.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
DONE_CRC_ERR is not a RNC suspension condition, so do not change the
state to expect the incoming suspension notification.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
[djbw: dropped DONE_CMD_LL_R_ERR change]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since libsas has it's own means to escalate SATA/STP device error
handling depending on task status codes, return all SATA/STP I/O
on the normal path.
i.e. skip sas_task_abort() and let sas_ata_task_done() disposition the
qc. Longer term we want to audit non-essential calls to
sas_task_abort().
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Based on original implementation from Jiangbi Liu and Maciej Trela.
ATAPI transfers happen in two-to-three stages. The two stage atapi
commands are those that include a dma data transfer. The data transfer
portion of these operations is handled by the hardware packet-dma
acceleration. The three-stage commands do not have a data transfer and
are handled without hardware assistance in raw frame mode.
stage1: transmit host-to-device fis to notify the device of an incoming
atapi cdb. Upon reception of the pio-setup-fis repost the task_context
to perform the dma transfer of the cdb+data (go to stage3), or repost
the task_context to transmit the cdb as a raw frame (go to stage 2).
stage2: wait for hardware notification of the cdb transmission and then
go to stage 3.
stage3: wait for the arrival of the terminating device-to-host fis and
terminate the command.
To keep the implementation simple we only support ATAPI packet-dma
protocol (for commands with data) to avoid needing to handle the data
transfer manually (like we do for SATA-PIO). This may affect
compatibility for a small number of devices (see
ATA_HORKAGE_ATAPI_MOD16_DMA).
If the data-transfer underruns, or encounters an error the
device-to-host fis is expected to arrive in the unsolicited frame queue
to pass to libata for disposition. However, in the DONE_UNEXP_FIS (data
underrun) case it appears we need to craft a response. In the
DONE_REG_ERR case we do receive the UF and propagate it to libsas.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This will synchronize the version string with internal driver.
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
with 1 expander, connect 8 HDD, the write performance will be
improved by 80%.
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-- change connection behavior
-- set bit8 to 1 for performance tuning
-- set bit0 to 0 to enable retry for no_dest reject case.
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
spin up issue: some direct attached SAS device can't spin up
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support for Marvell 88SE9480 SAS/SATA HBA
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Expanders fail to link when the phy rates are mismatched.
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Needed to jump to scic_lock unlock.
Also spotted by coccicheck.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Kill the local smp response buffer.
Besides being unnecessary, it is too small (currently truncates
responses to 60 bytes). The mid-layer will have already allocated a
sufficiently sized buffer, just kmap and copy into it directly.
Cc: <stable@kernel.org>
Reported-by: Derick Marks <derick.w.marks@intel.com>
Tested-by: Derick Marks <derick.w.marks@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Code Inspection: found two missing break directives. First one will
result in not retrying an a task that report
IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY, the second will result in cosmetic
debug printk conflicting statement stutter. Because checkpatch.pl came
up with a warning regarding unnecessary space before a newline on one of
the fragments associated with the diff context, I took the liberty of
fixing all the cases of this issue in the pair of files touched by this
defect. These cosmetic changes hide the break changes :-(
To help focus, break changes are in pm8001_hwi.c fragment line 1649 for
the IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY case statement and pm8001_sas.c
line 1000 deals with the conflicting debug print stutter.
Signed-off-by: Mark Salyzyn <mark_salyzyn@us.xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On the pm8001, when a device is in the process of going away (device
power off or hot plug), depending on the timing, the driver would return
SAS_PHY_DOWN as the return value to the queuecommand DEV_IS_GONE logic.
The net result is an near infinite retry (especially if SAS debugging is
enabled), the logs will fill with:
kernel: mpi_ssp_completion 2119:e21:SSP IO status 0x13 tag 0xcc1c0000
dlen=90 param=0xe
kernel: wwn=5000c50034069e86 cdb=12 00 00 00 5a 00 00 00 00 00 00 00 00
00 00 00
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
. . .
This patch changes to leverage the port_attached logic to complete the
command with a status of PHY_DOWN so that the disposition can be handled
immediately and correctly.
Signed-off-by: Mark Salyzyn <mark_salyzyn@us.xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently fcoe_ddp_min doesn't have default value
so by default not used, so setting up default value
as 4k as this works better by avoiding overhead
of programing DDP for small IOs.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use real dev in case it has HW vlan acceleration
support since in this case the real dev would
do needed vlan processing, this way unnecessary
vlan layer processing avoided and it gives
slightly better IOPS with 512B size IOs.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
fix holes and better cache aligned fields.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Re-arrange its fields to avoid padding and have better
cacheline alignments.
Removed not used start_time, end_time and last_pkt_time
fields.
This all reduced this struct size to 448 from 480 and
that also reduced one cacheline on x86_64 beside
eliminating 8 pads. However kept logical fields together.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since fcoe_percpu_thread_create() creates percpu kthread, it makes sense
to use kthread_create_on_node() to get proper NUMA affinity for kthread
stack.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Libsas forget to set the sas_address and device type of rphy lead to file
under /sys/class/sas_x show wrong value, fix that.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Tested-by: Crystal Yu <crystal_yu@usish.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas handles:
1/ limiting ata scanning to lun0
2/ changes to /sys/block/<sdX>/device/queue_depth for ata devices
libata handles turning off ncq globally via kernel command line
(libata.force=noncq) or sysfs (echo 1 >
/sys/block/<sdX>/device/queue_depth). A lldd specific compile option is
not necessary.
Cc: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas now handles:
1/ limiting ata scanning to lun0
2/ maximizing the queue_depth of sas devices (up to 256, mvsas only
supports 64)
3/ changes to /sys/block/<sdX>/device/queue_depth for ata devices
Acked-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The queue-depth for libsas-attached devices initializes to 32 and can
only be increased manually via sysfs to a max of 64, while mpt2sas
attached devices initialize to 254 and dynamically float via the
midlayer ->change_queue_depth interface.
No performance regression was observed with this change on the isci
driver.
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pass queue_depth change requests to libata, and prevent queue_type
changes for ATA devices.
Otherwise:
1/ we do not honor the libata specific restrictions on the queue depth
2/ libsas drivers that do not set sdev->tagged_supported are unable to
change the queue_depth of ata devices via sysfs
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently mvsas and pm8001 have custom ->slave_alloc implementations to
achieve this. Uplevel it for all libsas drivers as isci encounters problems
with atapi devices when scanning past lun0.
Just do what Darrick suggested [1], and limit the scan for ata devices.
[1] http://marc.info/?l=linux-scsi&m=116604101119861&w=2
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow expander table-to-table attachments for
expanders that support it.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
I hit a crash in qla2x00_abort_all_cmds() if the qla2xxx module is
unloaded right after it is loaded. I debugged this down to the abort
handling improperly treating a command of type SRB_ADISC_CMD as if it
had a bsg_job to complete when that command actually uses the iocb_cmd
part of the union. (I guess to hit this one has to unload the module
while the async FC initialization is still in progress)
It seems we should only look for a bsg_job if type is SRB_ELS_CMD_RPT,
SRB_ELS_CMD_HST or SRB_CT_CMD, so switch the test to make that explicit.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* git://bedivere.hansenpartnership.com/git/scsi-rc-fixes-2.6:
[SCSI] 3w-9xxx: fix iommu_iova leak
[SCSI] cxgb3i: convert cdev->l2opt to use rcu to prevent NULL dereference
[SCSI] scsi: qla4xxx needs libiscsi.o
[SCSI] libsas: fix failure to revalidate domain for anything but the first expander child.
[SCSI] aacraid: reset should disable MSI interrupt
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Following reports on the list, it looks like the 3e-9xxx driver will leak dma
mappings every time we get a transient queueing error back from the card.
This is because it maps the sg list in the routine that sends the command, but
doesn't unmap again in the transient failure path (even though the command is
sent back to the block layer). Fix by unmapping before returning the status.
Reported-by: Chris Boot <bootc@bootc.net>
Tested-by: Chris Boot <bootc@bootc.net>
Acked-by: Adam Radford <aradford@gmail.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This oops was reported recently:
d:mon> e
cpu 0xd: Vector: 300 (Data Access) at [c0000000fd4c7120]
pc: d00000000076f194: .t3_l2t_get+0x44/0x524 [cxgb3]
lr: d000000000b02108: .init_act_open+0x150/0x3d4 [cxgb3i]
sp: c0000000fd4c73a0
msr: 8000000000009032
dar: 0
dsisr: 40000000
current = 0xc0000000fd640d40
paca = 0xc00000000054ff80
pid = 5085, comm = iscsid
d:mon> t
[c0000000fd4c7450] d000000000b02108 .init_act_open+0x150/0x3d4 [cxgb3i]
[c0000000fd4c7500] d000000000e45378 .cxgbi_ep_connect+0x784/0x8e8 [libcxgbi]
[c0000000fd4c7650] d000000000db33f0 .iscsi_if_rx+0x71c/0xb18
[scsi_transport_iscsi2]
[c0000000fd4c7740] c000000000370c9c .netlink_data_ready+0x40/0xa4
[c0000000fd4c77c0] c00000000036f010 .netlink_sendskb+0x4c/0x9c
[c0000000fd4c7850] c000000000370c18 .netlink_sendmsg+0x358/0x39c
[c0000000fd4c7950] c00000000033be24 .sock_sendmsg+0x114/0x1b8
[c0000000fd4c7b50] c00000000033d208 .sys_sendmsg+0x218/0x2ac
[c0000000fd4c7d70] c00000000033f55c .sys_socketcall+0x228/0x27c
[c0000000fd4c7e30] c0000000000086a4 syscall_exit+0x0/0x40
--- Exception: c01 (System Call) at 00000080da560cfc
The root cause was an EEH error, which sent us down the offload_close path in
the cxgb3 driver, which in turn sets cdev->l2opt to NULL, without regard for
upper layer driver (like the cxgbi drivers) which might have execution contexts
in the middle of its use. The result is the oops above, when t3_l2t_get attempts
to dereference L2DATA(cdev)->nentries in arp_hash right after the EEH error handler sets it to NULL.
The fix is to prevent the setting of the NULL pointer until after there are no
further users of it. The t3cdev->l2opt pointer is now converted to be an rcu
pointer and the L2DATA macro is now called under the protection of the
rcu_read_lock(). When the EEH error path:
t3_adapter_error->offload_close->cxgb3_offload_deactivate
Is exectured, setting of that l2opt pointer to NULL, is now gated on an rcu
quiescence point, preventing, allowing L2DATA callers to safely check for a NULL
pointer without concern that the underlying data will be freeded before the
pointer is dereferenced.
This has been tested by the reporter and shown to fix the reproted oops
[nhorman: fix up unitinialised variable reported by Dan Carpenter]
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Karen Xie <kxie@chelsio.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
sector_t can be different types, so cast it to its largest possible
type.
drivers/scsi/qla2xxx/qla_isr.c:1509:5: warning: format '%lx' expects type 'long unsigned int', but argument 5 has type 'sector_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SCSI_ISCI needs to select SCSI_SAS_HOST_SMP to ensure that all
needed symbols are available to it.
Fixes this build error:
ERROR: "try_test_sas_gpio_gp_bit" [drivers/scsi/isci/isci.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the ipr driver decides to dump the adapter, it changes the
sdt_state to GET_DUMP, then prepares the adapter so that the dump
can be read. However, if the ipr worker thread wakes up for some
reason before the driver has put the adapter in a state where it
can succesfully dump the adapter, the driver will start dumping
the adapter too early, which can potentially trigger a BUG check
in the pci config blocking API. Fix this by adding a new
sdt_state to differentiate between the ipr driver wanting to dump
the adapter in the near future and wanting to dump the adapter now.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Gracefully handle bnx2fc_map_sg failure, so that queuecommand returns host busy
and SCSI-ml can retry the IO.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
scsi_dma_map doesn't work for NPIV since vport dev isn't fully initialized.
For more details: http://marc.info/?l=linux-scsi&m=118312448030633&w=2 and
commit - c59fd9ebc4.
Signed-off-by: Nithin Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The OSD protocol calls for all kind of security levels that use
CRYPTO_HMAC and SH1, but the current code only supports NO_SEC,
which does not use any of these.
Remove a wrong FIXME that calls for them. Thanks Maxin for
reporting on this.
Reported-by: "Maxin B. John" <maxin.john@gmail.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Sizeof a pointer-typed expression returns the size of the pointer, not that
of the pointed data.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *e;
type T;
identifier f;
@@
f(...,(T)e,...,
-sizeof(e)
+sizeof(*e)
,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mutual exclusion is redundant here because all the paths in the call graph
leading to esp_driver_ops.send_dma_cmd() happen under spin_lock_irqsave/
spin_lock_irqrestore. Remove it.
Tested on a Mac Quadra 660av and a Mac LC 630.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Support added for controllers capable of multi reply queues.
The following are the modifications to the driver to support NUMA.
1) Create the new structure adapter_reply_queue to contain the reply queue
info for every msix vector. This object will contain a
reply_post_host_index, reply_post_free for each instance, msix_index, among
other parameters. We will track all the reply queues on a link list called
ioc->reply_queue_list. Each reply queue is aligned with each IRQ, and is
passed to the interrupt via the bus_id parameter.
(2) The driver will figure out the msix_vector_count from the PCIe MSIX
capabilities register instead of the IOC Facts->MaxMSIxVectors. This is
because the firmware is not filling in this field until the driver has
already registered MSIX support.
(3) If the ioc_facts reports that the controller is MSIX compatible in the
capabilities, then the driver will request for multiple irqs. This count
is calculated based on the minimum between the online cpus available and
the ioc->msix_vector_count. This count is reported to firmware in the
ioc_init request.
(4) New routines were added _base_free_irq and _base_request_irq, so
registering and freeing msix vectors were done thru simple function API.
(5) The new routine _base_assign_reply_queues was added to align the msix
indexes across cpus. This will initialize the array called
ioc->cpu_msix_table. This array is looked up on every MPI request so the
MSIxIndex is set appropriately.
(6) A new shost sysfs attribute was added to report the reply_queue_count.
(7) User needs to set the affinity cpu mask, so the interrupts occur on the
same cpu that sent the original request.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds couple more Vendor/Product IDs for RDAC.. There are no
functional changes.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Basic support to initialize the gpio unit, accept an incomming
SAS_GPIO_REG_TX_GP bitstream, and translate it to the ODx.n fields in
the hardware registers. If register indexes outside the supported range
are specified in the SMP frame we simply accept the write and return how
many registers (SFF-8485) were written (libsas reports this as residue
in the request).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
output_data_select registers are off by one u32
delete the macros we will never use.
Reported-by: Artur Wojcik <artur.wojcik@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add SFF-8485 v0.7 / SAS-1 smp-write-gpio register support to libsas.
Defer SAS-2 support unless/until it defines an sgpio interface.
Minimum implementation needed to get the lights blinking.
try_test_sas_gpio_gp_bit() provides a common method to parse the
incoming write data (raw bitstream), and the to_sas_gpio_gp_bit() helper
routine can be used as a basis for the set/clear operations for the
'read' implementation. Host implementations parse as many bits
(ODx.[012]) as are locally supported and report the number of registers
successfully written. If the submitted data overruns the internal
number of registers available report the write as a success with the
number of bytes remaining reported in ->resid_len.
Example (assuming an active backplane) set the "identify" pattern for
the first 21 devices:
smp_write_gpio --count=2 --data=92,49,24,92,24,92,49,24 -t 4 --index=1 /dev/bsg/sas_hostX
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In an enclosure model where there are chaining expanders to a large body
of storage, it was discovered that libsas, responding to a broadcast
event change, would only revalidate the domain of first child expander
in the list.
The issue is that the pointer value to the discovered source device was
used to break out of the loop, rather than the content of the pointer.
This still remains non-compliant as the revalidate domain code is
supposed to loop through all child expanders, and not stop at the first
one it finds that reports a change count. However, the design of this
routine does not allow multiple device discoveries and that would be a
more complicated set of patches reserved for another day. We are fixing
the glaring bug rather than refactoring the code.
Signed-off-by: Mark Salyzyn <msalyzyn@us.xyratex.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
qla4xxx now uses iscsi_boot_sysfs to export the targets used
for boot to sysfs. It needs to select that config option
to make sure that module is also built.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Firmware asserts when the same CQE is armed twice. This scenario happens during
RSCN stress tests as driver incorrects arms the CQ after the session is
offloaded.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It is not required to hold rtnl_lock and bnx2fc_dev_lock when calling
bnx2fc_if_destroy, as the locking is only required to serialize creation and
deletion of fcoe instances. More importantly, this unnecessary locking causes
deadlock as bnx2fc_if_destroy calls fc_remove_host holding rtnl_lock.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When bnx2fc receives an UNREGISTER event on a vlan interface it calls
destroy on all interfaces that matches the physical interface. Add
vlan_id check to destroy only the vlan interface that generated the
event.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
ABTS was not issued for timed out REC, as REC completion handler exits out if
the IO completed. Check for timed out REC and issue ABTS before proceeding with
further processing in REC completion handler. Also, initialize rec_retry and
srr_retry before starting the IO.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Link up event is generated to the driver even before vlan discovery has
started. Because of this driver can send discovery solicitation on a stale
vlan. Call fcoe_ctlr_link_up() only when the driver is in enabled state, which
implies the vlan discovery is complete before sending solicitation.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the max receive frame size is changed during link down, the driver uses the
same value after linkup unless it is reset to default.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch does several things:
- introduces __ethtool_get_settings which is called from ethtool code and
from drivers as well. Put ASSERT_RTNL there.
- dev_ethtool_get_settings() is replaced by __ethtool_get_settings()
- changes calling in drivers so rtnl locking is respected. In
iboe_get_rate was previously ->get_settings() called unlocked. This
fixes it. Also prb_calc_retire_blk_tmo() in af_packet.c had the same
problem. Also fixed by calling __dev_get_by_index() instead of
dev_get_by_index() and holding rtnl_lock for both calls.
- introduces rtnl_lock in bnx2fc_vport_create() and fcoe_vport_create()
so bnx2fc_if_create() and fcoe_if_create() are called locked as they
are from other places.
- use __ethtool_get_settings() in bonding code
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v2->v3:
-removed dev_ethtool_get_settings()
-added ASSERT_RTNL into __ethtool_get_settings()
-prb_calc_retire_blk_tmo - use __dev_get_by_index() and lock
around it and __ethtool_get_settings() call
v1->v2:
add missing export_symbol
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> [except FCoE bits]
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in drivers/scsi/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a resend from the original, changing the title from PATCH to
RFC(since this is a review for commit, and I should have put that the first go around).
and also removing some of the commit's with ia64 and bash since it is significant.
let me know if I might have missed anything etc..
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since printk_ratelimit() shouldn't be used anymore (see comment in
include/linux/printk.h), replace it with printk_ratelimited.
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* git://bedivere.hansenpartnership.com/git/scsi-rc-fixes-2.6: (25 commits)
[SCSI] bnx2i: Fixed the endian on TTT for NOP out transmission
[SCSI] libfc: fix referencing to fc_fcp_pkt from the frame pointer via fr_fsp()
[SCSI] libfc: block SCSI eh thread for blocked rports
[SCSI] libfc: fix fc_eh_host_reset
[SCSI] fcoe: Fix deadlock between fip's recv_work and rtnl
[SCSI] qla2xxx: Update version number to 8.03.07.07-k.
[SCSI] qla2xxx: Set the task attributes after memsetting fcp cmnd.
[SCSI] qla2xxx: Correct inadvertent loop state transitions during port-update handling.
[SCSI] qla2xxx: Save and restore irq in the response queue interrupt handler.
[SCSI] qla2xxx: Double check for command completion if abort mailbox command fails.
[SCSI] qla2xxx: Acquire hardware lock while manipulating dsd list.
[SCSI] qla2xxx: Fix qla24xx revision check while enabling interrupts.
[SCSI] qla2xxx: T10 DIF - Fix incorrect error reporting.
[SCSI] qla2xxx: T10 DIF - Handle uninitalized sectors.
[SCSI] hpsa: fix physical device lun and target numbering problem
[SCSI] hpsa: fix problem that OBDR devices are not detected
[SCSI] isci: add version number
[SCSI] isci: fix event-get pointer increment
[SCSI] isci: dynamic interrupt coalescing
[SCSI] isci: Leave requests alone if already terminating.
...
When CONFIG_NET is disabled, SCSI_QLA_ISCSI selects SCSI_ISCSI_ATTRS,
which uses network interfaces, so the build fails with multiple errors:
warning: (ISCSI_TCP && SCSI_CXGB3_ISCSI && SCSI_CXGB4_ISCSI && SCSI_QLA_ISCSI && INFINIBAND_ISER) selects SCSI_ISCSI_ATTRS which has unmet direct dependencies (SCSI && NET)
ERROR: "skb_trim" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "netlink_kernel_create" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "netlink_kernel_release" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
...
so make SCSI_QLA_ISCSI also depend on NET to prevent the build errors.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: iscsi-driver@qlogic.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The alua device handler starts the first retry after 10 seconds,
and increases it times 10 for each round.
This leads to an unnecessary delay. This patch modifies it to
start after one second, and increase by a factor of two.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For Target Portal Group IDs occupying the full 2 bytes in the
RTPG response, the following group_id check in the alua_rtpg
routine always fails in scsi_dh_alua.c:
if (h->group_id == (ucp[2] << 8) + ucp[3]) {
This causes the ALUA handler to wrongly identify the AAS of
a specified device as well as incorrectly interpreting the
supported AAS of the target as seen by the following entries
in the /var/log/messages:
"alua: port group 3ea state A supports tousna"
"alua: port group 3e9 state A supports tousna"
This is because 'ucp' is wrongly declared in alua_rtpg as
a character pointer instead of an unsigned character pointer.
Signed-off-by: Martin George <marting@netapp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Avoid attaching a hardware handler to a device which is
already scheduled for deletion.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When activating a patch we should always update the TPGS state
as it might have changed in between.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some device handler types are not tied to the vendor/model
but rather to a specific capability. Eg ALUA is supported
if the 'TPGS' setting in the standard inquiry is set.
This patch implements a 'match' callback for device handler
which supersedes the original vendor/model lookup and
implements the callback for the ALUA handler.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixup some kernel-doc comments to reference to the
correct function name.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of issuing a standard inquiry from within the
alua device handler we can evaluate the TPGS setting from
the existing inquiry data of the sdev and save us the I/O.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
->queuecommand must return either 0, or one of the SCSI_MLQUEUE_* return
values. Non-transient errors are indicated by setting cmd->result before
calling ->scsi_done and returning 0. Fix libsas to adhere to this calling
convention. Note that the DID_ERROR for returns from the low-level driver
might not be correct for all cases, but it's the best we can do with
the current layering in libsas. I also suspect that the pre-existing
handling of -SAS_QUEUE_FULL should really be SCSI_MLQUEUE_HOST_BUSY, but
I'll leave that for a separate change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Switch sas_queuecommand to a normal indentation and goto based error handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
sd_ioctl() still use printk() for log output.
It should use sd_printk() instead of printk(), as well as other sd_*.
All SCSI messages should output via s*_printk() instead of printk().
Signed-off-by: Nao Nishijima <nao.nishijima.xt@hitachi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since it is already called in the right context with rtnl_lock and dev_mutex
held.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix SYSFS interface issues.
- In the lpfc_sli4_pdev_status_reg_wait() routine, after initial 100ms delay
following write to PHYSDEV_CONTROL register for the firmware reaction, check
the RN bit and ERR bit of the SLIPORT_STATUS register. If none of them
became 1, the previous PHYSDEV_CONTROL register should be considered failed
due to lack of privilege and error for no permission should be returned
immediately without getting into the wait for RDY bits on the SLIPORT_STATUS
register.
- Remove the driver check on dev->is_physfn before proceed to perform the
PHYSDEV_CONTROL register write, and let the PCI function's privilege
setting and driver handling of PHYSDEV_CONTROL register write failure to
handle the reset-ability through the SLI port.
- Added key to ctlreg_write to prevent unauthorized or unexpected write to
the control register.
- Change return to EACCES for sysfs access that are failed because hba_reset
is disabled.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix HBA initialization issues
- Swap all values that come from the firmware image on little endian systems.
Created a new bf_get_be macro that does the same as the bf_get_le macro but
for big endian data instead of little endian data.
- Moved the incrementing of temp_offset after the copy
fixed the write object loop to use temp_offset to figure out where the end
of the image is instead of offset.
- Added the necessary codes for properly bringing the driver instance offline
and then trying to bring the port back online with the PCI function IP reset.
If it fails to bring the SLI port back online, it will fall through to
bringing the SLI port to HBA error offline.
- Add a call in the probe_one_s3 and probe_one_s4 routines to get the Modeldesc
- Change OCe50100 to OCe15100
- Made the error log also include the PCI BAR bitmap returned from kernel call
pci_select_bars().
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix issues pertaining to SCSI/FC protocol.
- Allow frames destined to 0xFFFFFE to be processed by the driver by matching
that DID with the physical port.
- Call lpfc_sli_issue_iocb with context1 set to ndlp
- In echo command accept function, adjust memcpy to limit memcpy to 1K
- Set LPFC_SLI3_BG_ENABLED properly upon completion.
- Skip the INIT_VFI call in lpfc_register_fcf if the FCF is already
registered and go immediately to initial flogi.
- use "status" variable instead of "ret" variable to hold the return of the
fc_block_scsi_eh.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds call to pci_disable_device during
rmmod and shutdown. The lack of this call was causing hang in
insmod - rmmod loop test
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds a shutdown routine. It fixes a bug where when be2net
and be2iscsi are both used be2iscsi was not cleaning up its resources
properly causing be2net to fail to get loaded when the system is
rebooted.
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix be2iscsi driver to use a separate pointer for each irq action->name
field and avoid display corruption in /proc/interrupts. The be2iscsi driver
was using a single static array in a function for the irq action->name field.
This results in garbage output from /proc/interrupts
The pointer for action->name is garbage and scribbles the output on the screen.
This patch fixes the problem:
156: 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 PCI-MSI-X beiscsi_msix_0017
This patch is based on Prarit's patch here:
http://www.spinics.net/lists/linux-scsi/msg52325.html
but I have fixed up the failure paths and removed
redundant check for !i suggested by Eike.
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since active_mask is first assigned in an "else" block, the compiler throws
a warning saying that the active_mask variable may be used uninitialized in
a print statement later. Initialize active_mask to 0 in the declaration to
stop the warning.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Return sysfs error codes that match the conditions encountered.
This prevents sysfs from retrying a request which is conditioned
to fail under the current circumstance.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Provide bsg interface for updating VPD attached on the I2C serial bus.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Corrects the return value for the cases where read/write edc fails;
this prevents sysfs from retrying the operation until forever.
Corrects the printk width specifier for the first byte of buf.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver is not releasing the lock if ql2xdontresethba is set, this might lead
to a lockup.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Minidump allows us to catpure a snapshot of the firmware/hardware states at the
time of failure for further analysis.
[jejb: added missing #include <linux/vmalloc.h>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> ]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi_nopout task's TTT is defined as __be32 while the DMA
memory to the chip is CPU specific. This creates a problem for
unsolicited NOP-In responses where the TTT is not the RESERVED
tag of 0xFFs. This patch adds a call to be32_to_cpu for the TTT
specified.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In commit 6a716a8, while releasing the DDP context in case frame_send() failed,
the frame may already be freed, so we should store the pointer to fc_fcp_pkt and
release the DDP context using the locally stored fsp instead of getting fsp from
the fr_fsp(fp) on a frame.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Reported-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Call fc_block_scsi_eh() in all fcoe eh to blocks
the scsi_eh thread for blocked rports.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Current fc_eh_host_reset leaves lport offline
permanently due to FLOGI response getting
handled by LOGO response from last reset as both
had same exchange id.
So fix this by having end to end exches clean-up
using exchange abort along exches reset
done from fc_eh_host_reset. This would avoid
exchanges collision between the sessions across
the reset. In this case implicit login should have
done that but no aborting support for FIP
frames, so just wait till lport->r_a_tov before
restarting next flogi to ensure all exchanges
are good to use again for next session.
Below is the trace of LOGO from older session
coming ahead of FLOGI response with same exche id
0x203:-
617 86.435165 4e.00.0b -> ff.ff.fc FC ELS LOGO 0x203
618 86.435195 4e.00.0b -> b6.02.00 FC ELS LOGO 0x213
619 86.435220 4e.00.0b -> 18.03.00 FC ELS LOGO 0x223
620 86.435244 4e.00.0b -> 18.02.00 FC ELS LOGO 0x233
621 86.435267 4e.00.0b -> 18.01.00 FC ELS LOGO 0x243
622 86.435349 00.00.00 -> ff.ff.fe FC ELS FLOGI 0x203
623 86.435549 ff.ff.fc -> 4e.00.0b FC ELS ACC (LOGO) 0x203
624 86.438721 ff.ff.fe -> 4e.00.0b FC ELS ACC (FLOGI) 0x203
625 86.442059 18.03.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x223
626 86.443683 b6.02.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x213
627 86.447693 18.01.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x243
628 86.453499 18.02.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x233
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Increase it to NVRAM configured limit or 1024 whichever is less.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DIF/DIX support for zfcp is no longer experimental,
and config option is no longer necessary.
Return error from queuecommand for unsupported data directions.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The Marvell Universal Message Interface (UMI) defines a messaging
interface between host and Marvell products (Plato, for example). It
considers situations of limited system resource and optimized system
performance.
UMI driver translates host request to message and sends message
to FW via UMI, FW receives message and processes it, then sends response
to UMI driver.
FW generates an interrupt when it needs to send information or
response to UMI driver
Signed-off-by: Jianyun Li <jyli@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Export the name of iface session is attached to. This is needed
so tools like iscsiadm/iscsistart can match the sessions to
userspace ifaces when rebuilding iscsid's state during boot.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added new sysfs attr 'host_reset' in scsi_sysfs.c to
perform adapter or firmware reset as suggested by
Mike Christie here:
http://marc.info/?l=linux-scsi&m=127359347111167&w=2
user/application can write "adapter" or "firmware" on
this attr and it will call newly added function hook
in scsi_host_template to call LDD adapter or firmware
reset implementation.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This command is used to read ACB params from firmware
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This command will causes the firmware to update all
configurations to pre-defined factory default settings.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some CD-ROMs fail to report a media change correctly. The specific
one for this patch simply fails to respond to commands, then gives a
UNIT ATTENTION after being reset which returns ASC/ASCQ 28/00. This
is out of spec behaviour, but add a check in the eat CC/UA on reset
path to catch this case so the CD-ROM will function somewhat properly.
[jejb: fixed up white space and accepted without signoff]
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hook qla4xxx in fw boot sysfs interface so iscsi tools
can use the info to create boot sessions.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
1. Remove device database entry (ddb) state.
2. Remove device database (DDB) list building.
With open-iscsi integration the logins to the target devices are
handled by the user space. So the information of target is now
maintained in the iscsi_session object. This is handled at
libiscsi level so there is no need to maintain a list of DDBs in
the qla4xxx LLD.
3. qla4xxx: Remove add_device_dynamically.
Since autologin in FW is disabled with open-iscsi integration,
driver will never get an AEN for which driver has not requested
a DDB index. So remove the add_device_dynamically function.
4. Remove qla4xxx_tgt_dscvr
Since firmware autologin is disabled this function will not work.
Now user has the ability to do the target discovery and login to
each target individually. Firwmare will not do the login on its own.
5. Remove relogin related code
All relogin is handled by userspace now. qla4xxx just need to
notify userspace of a connection failure, this triggers the
relogin.
6. Remove add_session and alloc_session
Now qla4xxx uses iscsi_session_setup that would do the necessary
allocations for session and ddb_entry.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add scsi_transport_iscsi hooks in qla4xxx to support
iSCSI session management using iscsiadm.
This patch is based on discussion here
http://groups.google.com/group/open-iscsi/browse_thread/thread/e89fd888baf656a0#
Now users can use iscsiadm to do target discovery and do login/logout to
individual targets using the qla4xxx iSCSI class interface.
This patch leaves some dead code, but to make it easier to review
we are leaving and in the next patch we will remove that old code.
V2 - NOTE: Added code to avoid waiting for AEN during login/logout
in the driver, instead added a kernel to user event
to notify iscsid about login status. Because of this
iscsid will not get blocked.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Offload drivers like qla4xxx will offload the sending of the login/logout
pdus still, so this patch adds iscsi_conn_login_event which is
used by these types of drivers to notify userspace that the connection
has changed state.
It also adds a iscsi_is_session_online helper so the lld
can query the sessions state field.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds bsg support to qla4xxx.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds bsg support to the iscsi class. There is only
1 request, the host vendor one, supported. It is expected that
this would be used for things like flash updates.
This patch is made over this one
http://marc.info/?l=linux-scsi&m=131149780020992&w=2
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support to set VLAN and show vlan settings in sysfs
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
[Patch updated to new defines]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libiscsi does not support markers and if someone tries
to set them the driver does a BUG(). There is not need
to be that extreme. Just return -ENOSYS.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support to set vlan priority and enable/disble a vlan.
Patch based on code from Vikas Chaudhary.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
iscsi_session_to_shost is a macro around dev_to_shost which returns a
Scsi_Host so there is no need to cast.
iscsi_session_to_shost is a macro around shost_priv which
returns a void pointer so no need to cast.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's host attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We can replace the iface param mask with the
attr_is_visible callback.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's session attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and drivers to use the attribute container
sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A iscsi host can have multiple interfaces. This patch
adds a new iface iscsi class for this. It exports the
network settings now, and will be extended to also
export iscsi initiator port settings like the isid
and initiator name for drivers that can support multiple
initiator ports.
Based on patch from Lalit Chandivade.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Move all ipaddress related param to "struct ipaddress_config"
from "struct scsi_qla_host"
- update function - qla4xxx_update_local_ip()
- Rename IPOPT_IPv4_PROTOCOL_ENABLE to IPOPT_IPV4_PROTOCOL_ENABLE
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
[update for new ISCSI_IFACE values]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allows user space (iscsiadm) to send down network configuration
parameters for LLD to set private network configuration on the iSCSI
adapters.
Based on patches from Vikas Chaudhary.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allows user space (iscsiadm) to send down network configuration
parameters for LLD to set private network configuration on the iSCSI
adapters.
Based on patch from Lalit Chandivade.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During kdump testing I noticed timeouts when initialising each IPR
adapter. While the driver has logic to detect an adapter in an
indeterminate state, it wasn't triggering and each adapter went
through a 5 minute timeout before finally going operational.
Some analysis showed the needs_hard_reset flag wasn't getting set.
We can check the reset_devices kernel parameter which is set by
kdump and force a full reset. This fixes the problem.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds a validation step before allowing creation of a new NPIV port.
It checks whether the WWPN passed for the new NPIV port to be created is unique
for the given physical port.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
bnx2x driver would obtain the WWNN/WWPN from the shared memory and can be
obtained by the bnx2fc driver via ndo_fcoe_get_wwn.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Export fcoe_get_wwn, fcoe_validate_vport_create and fcoe_wwn_to_str so that all
LLDs can use these common function.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As an initiator, driver need not handle incoming ABTS. It initiates an ABTS if
any IO requests time out.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Free session resources before rport logoff
- Do not free session resources in bnx2fc_alloc_session_resc() as it is handled
in caller's error handling path.
- Do not call bnx2fc_free_session_resc() if bnx2fc_init_tgt() fails as cq_lock
is not yet initialized.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There exists a race condition between CQ doorbell unmap and IO completion path
that arms the CQ which causes a NULL dereference. Protect the ctx_base with
cq_lock to avoid this. Also, wait for the CQ doorbell to be successfully mapped
before arming the CQ.
Also, do not count uncolicited CQ completions for free_sqes.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During the unsolicited LOGO processing, the session is uploaded and offloaded
after the relogin is complete. In between any new IOs are errored back as the
upload completion flag is set. Upon exhausting the retry count, the application
fails the IOs. Return target busy for all the cases when session is not ready.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
CFC_DELETE is issued 2 secs after CONN_TERM is completed. If the session is
uploaded and offloaded immediately, it has to wait for the connection id to be
available.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since this flag was never cleared, the driver does not wait for firmware
destroy completions, causing missed KCQEs.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since the driver holds the reference for vlan netdev, the reference has to be
released by the driver when the vlan device is removed. Driver handles this in
NETDEV_UNREGISTER event.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Move interface specific cleanup functionality to from bnx2fc_if_destroy to
bnx2fc_interface_cleanup. Do not access interface/hba in bnx2fc_if_destroy as
by the time this function is called interface may already be destroyed. This
patch is in preparation to handle NETDEV_UNREGISTER on a vlan device.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Change them to bnx2fc_interface_setup/bnx2fc_interface_cleanup in preperation
for the patches to follow. Interface specific cleanup functionality will be
moved to bnx2fc_interface_cleanup.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When NPIV ports are created/deleted rapidly there is a race condition between
bnx2fc_vport_destroy() from sysfs and bnx2fc_flogi_resp(), which could try to
delete the NPIV port from the list twice. Fix is to loop through the list of
NPIV ports to find a match, and only when it exists remove it.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During sequence cleanup, an additional reference for an IO has been
taken. Because of this, the IO is never released into the free list.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Look up p->work_list to process cq completions, and correct the error check for
thread creation.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reset max receive frame size every time before attempting FLOGI. Without this,
the stale MFS value will be used.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
mpt2sas_base_detach() call was removed from _scsih_remove() while
doing some code shuffling. Mainly when we work on adding code for
scsih_shutdown(). I have added back mpt2sas_base_detach() which will
get callled from _scsih_remove().
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Now that isci has added a 3rd open coded user of this functionality just
share the libsas version.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Moger, Babu