xhci_find_next_ext_cap doesn't check for PCI hotplug removal and may use
the PCI master abort bit pattern (~0) to calculate a new PCI address
offset to read/write. The has lead to reproducable crashes when testing
surprise removal during device initialization on a Stratus platform, at
least after commit d5ddcdf4d6 ("xhci: rework xhci extended capability
list parsing functions").
The crash is repeatable on a Stratus platform when injecting hardware
faults to induce xHCI host controller hotplug during driver
initialization. If a PCI read in xhci_find_next_ext_cap returns the
master abort pattern, quirk_usb_handoff_xhci may start using a bogus
ext_cap_offset to start searching more bogus PCI addresses.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the existing two extended capability parsing helper functions with
one called xhci_find_next_ext_cap().
The extended capabilities are read both in pci-quirks before xhci driver is
loaded, and inside the xhci driver when adding ports. The existing helpers
did not suit well for these cases and a lot of custom parsing code was
needed.
The new helper function simplifies these two cases a lot.
The motivation for this rework was that code to support xhci debug
capability needed to parse extended capabilities, and it included
yet another capability parsing helper specific for its needs. With
this solution it debug capability code can use this new helper as well
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wrong capability bit was checked for best effort service latency.
bit 20 indicate port is BESL LPM capable (BLC),
bit 19 is hardware LPM capable (HLC)
This patch should be backported to kernels as old as 3.11, that
contain the commit a558ccdcc7 "usb: xhci:
add USB2 Link power management BESL support"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Steve Cotton <steve@s.cotton.clara.co.uk>
Cc: stable@vger.kernel.org
usb 2.0 devices with link power managment (LPM) can describe their idle link
timeouts either in BESL or HIRD format, so far xHCI has only supported HIRD but
later xHCI errata add BESL support as well
BESL timeouts need to inform exit latency changes with an evaluate
context command the same way USB 3.0 link PM code does.
The same xhci_change_max_exit_latency() function is used as with USB3
but code is pulled out from #ifdef CONFIG_PM as USB2.0 BESL LPM
funcionality does not depend on CONFIG_PM.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Re-define XHCI_LEGACY_DISABLE_SMI and used it in right way. All SMI enable
bits will be cleared to zero and flag bits 29:31 are also cleared to zero.
Other bits should be presvered as Table 146.
This patch should be backported to kernels as old as 2.6.31.
Signed-off-by: Alex He <alex.he@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Check the host's USB2 LPM capability.
USB2 software LPM support is optional for xHCI 0.96 hosts. xHCI 1.0 hosts
should support software LPM, and may support hardware LPM.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xHCI 1.0 spec specifies the xHC shall halt within 16ms after software clears
Run/Stop bit. In xHCI 0.96 spec the time limit is 16 microframes (2ms), it's
too short and often cause dmesg shows "Host controller not halted, aborting
reset." message when rmmod xhci-hcd.
Modify the time limit to comply with xHCI 1.0 specification and prevents the
warning message showing when remove xhci-hcd.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
According "5.3.6 Capability Parameters (HCCPARAMS)" of xHCI rev0.96 spec,
value of xECP register indicates a relative offset, in 32-bit words,
from Base to the beginning of the first extended capability.
The wrong calculation will cause BIOS handoff fail (not handoff from BIOS)
in some platform with BIOS USB legacy sup support.
Signed-off-by: Edward Shao <laface.tw@gmail.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the first of many patches to add support for USB 3.0 devices and
the hardware that implements the eXtensible Host Controller Interface
(xHCI) 0.95 specification. This specification is not yet publicly
available, but companies can receive a copy by becoming an xHCI
Contributor (see http://www.intel.com/technology/usb/xhcispec.htm).
No xHCI hardware has made it onto the market yet, but these patches have
been tested under the Fresco Logic host controller prototype.
This patch adds the xHCI register sets, which are grouped into five sets:
- Generic PCI registers
- Host controller "capabilities" registers (cap_regs) short
- Host controller "operational" registers (op_regs)
- Host controller "runtime" registers (run_regs)
- Host controller "doorbell" registers
These some of these registers may be virtualized if the Linux driver is
running under a VM. Virtualization has not been tested for this patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Joe Lawrence