The FORTIFY_SOURCE tests were split between bugs.c and fortify.c. Move
tests into fortify.c, standardize their naming, add CONFIG hints, and
add them to the lkdtm selftests.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210818174855.2307828-3-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CONFIG hints about why the ARRAY_BOUNDS test might fail, and
similarly include the CONFIGs needed to pass the ARRAY_BOUNDS test via
the selftests, and add to selftests.
Cc: kernelci@groups.io
Suggested-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210818174855.2307828-2-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake in a dev_dbg debug message. Fix it.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210815214206.47970-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
General Electric Healthcare's PPD has a secondary processor from
NXP's Kinetis K20 series. That device has two SPI chip selects:
The main interface's behaviour depends on the loaded firmware
and is currently unused.
The secondary interface can be used to update the firmware using
EzPort protocol. This is implemented by this driver using the
kernel's firmware API. The firmware is being flashed into
non-volatile flash memory, so it is enough to flash it once
and not on every boot. Flashing will wear the flash memory
(it has a life time of at least 10k programming cycles). At
the same time only occasional FW updates are expected (like e.g.
a BIOS update). Thus the firmware update is triggered via sysfs
instead of doing it in the driver's probe routine like many
other drivers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210802172309.164365-4-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Tegra186 and later, a portion of the SYSRAM may be reserved for use
by TZ. Non-TZ memory accesses to this portion, including speculative
accesses, trigger SErrors that bring down the system. This does also
happen in practice occasionally (due to speculative accesses).
To fix the issue, add a flag to the SRAM driver to only map the
device tree-specified reserved areas depending on a flag set
based on the compatibility string. This would not affect non-Tegra
systems that rely on the entire thing being memory mapped.
If 64K pages are being used, we cannot exactly map the 4K regions
that are placed in SYSRAM - ioremap code instead aligns to closest
64K pages. However, since in practice the non-accessible memory area
is 64K aligned, these mappings do not overlap with the non-accessible
memory area and things work out.
Reviewed-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Link: https://lore.kernel.org/r/20210715103423.1811101-1-mperttunen@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().
Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.
Cc: Robin Holt <robinmholt@gmail.com>
Cc: Steve Wahl <steve.wahl@hpe.com>
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20210803141621.780504-17-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Buffers and structures passed to MEI bus and client API can be made
const for safer code and clear indication that it is not modified.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210729102803.46289-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
put_tty_driver() is an alias for tty_driver_kref_put(). There is no need
for two exported identical functions, therefore switch all users of
old put_tty_driver() to new tty_driver_kref_put() and remove the former
for good.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the parent pointer of the misc device to ensure a relationship
between PCI and misc dev. That way it is possible to see in
/sys/class/misc/ which pci_endpoint_test instance serves what
PCI device.
Signed-off-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20210706154310.26773-1-richard@nod.at
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The virtual machine monitor (QEMU) exposes the pvpanic-pci
device to the guest. On guest side the module exists but
currently isn't loaded automatically. So the driver fails
to be probed and does not its job of handling guest panic
events.
Instead of requiring manual modprobe, let's include a device
database using the MODULE_DEVICE_TABLE macro and let the
module auto-load when the guest gets exposed with such a
pvpanic-pci device.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20210629072214.901004-1-eric.auger@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
refcount_t type and corresponding API can protect refcounters from
accidental underflow and overflow and further use-after-free situations.
Acked-by: Dimitri Sivanich <sivanich@hpe.com>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Link: https://lore.kernel.org/r/1626517043-42696-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core ignores the return value of this callback because there
is only little it can do when a device disappears.
This is the final bit of a long lasting cleanup quest where several
buses were converted to also return void from their remove callback.
Additionally some resource leaks were fixed that were caused by drivers
returning an error code in the expectation that the driver won't go
away.
With struct bus_type::remove returning void it's prevented that newly
implemented buses return an ignored error code and so don't anticipate
wrong expectations for driver authors.
Reviewed-by: Tom Rix <trix@redhat.com> (For fpga)
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio)
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts)
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media)
Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform)
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com> (For xen)
Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd)
Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb)
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus)
Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio)
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec)
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack)
Acked-by: Geoff Levand <geoff@infradead.org> (For ps3)
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt)
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th)
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia)
Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI)
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr)
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid)
Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM)
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa)
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire)
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid)
Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox)
Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss)
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC)
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups. Highlights
are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM4qQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylKvQCfbh+OmTkDlDlDhSWlxuV05M1XTXoAoLUcLZru
s5JCnwSZztQQLMDHj7Pd
=Zupm
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM7jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yloDQCfZOlLYXF+2KgXJQqevNnRiu7/B1gAn3aCX6xh
UWVUfu5LDIXi2uFERRT1
=Ze3R
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core changes from Greg KH:
"Here is the small set of driver core and debugfs updates for 5.14-rc1.
Included in here are:
- debugfs api cleanups (touched some drivers)
- devres updates
- tiny driver core updates and tweaks
Nothing major in here at all, and all have been in linux-next for a
while with no reported issues"
* tag 'driver-core-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
docs: ABI: testing: sysfs-firmware-memmap: add some memmap types.
devres: Enable trace events
devres: No need to call remove_nodes() when there none present
devres: Use list_for_each_safe_from() in remove_nodes()
devres: Make locking straight forward in release_nodes()
kernfs: move revalidate to be near lookup
drivers/base: Constify static attribute_group structs
firmware_loader: remove unneeded 'comma' macro
devcoredump: remove contact information
driver core: Drop helper devm_platform_ioremap_resource_wc()
component: Rename 'dev' to 'parent'
component: Drop 'dev' argument to component_match_realloc()
device property: Don't check for NULL twice in the loops
driver core: auxiliary bus: Fix typo in the docs
drivers/base/node.c: make CACHE_ATTR define static DEVICE_ATTR_RO
debugfs: remove return value of debugfs_create_ulong()
debugfs: remove return value of debugfs_create_bool()
scsi: snic: debugfs: remove local storage of debugfs files
b43: don't save dentries for debugfs
b43legacy: don't save dentries for debugfs
...
Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanna driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems mushed
together" tree...
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM8jQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymECgCg0yL+8WxDKO5Gg5llM5PshvLB1rQAn0y5pDgg
nw78LV3HQ0U7qaZBtI91
=x+AR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanalabs driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems
mushed together" tree...
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
mcb: Use DEFINE_RES_MEM() helper macro and fix the end address
PNP: moved EXPORT_SYMBOL so that it immediately followed its function/variable
bus: mhi: pci-generic: Add missing 'pci_disable_pcie_error_reporting()' calls
bus: mhi: Wait for M2 state during system resume
bus: mhi: core: Fix power down latency
intel_th: Wait until port is in reset before programming it
intel_th: msu: Make contiguous buffers uncached
intel_th: Remove an unused exit point from intel_th_remove()
stm class: Spelling fix
nitro_enclaves: Set Bus Master for the NE PCI device
misc: ibmasm: Modify matricies to matrices
misc: vmw_vmci: return the correct errno code
siox: Simplify error handling via dev_err_probe()
fpga: machxo2-spi: Address warning about unused variable
lkdtm/heap: Add init_on_alloc tests
selftests/lkdtm: Enable various testable CONFIGs
lkdtm: Add CONFIG hints in errors where possible
lkdtm: Enable DOUBLE_FAULT on all architectures
lkdtm/heap: Add vmalloc linear overflow test
lkdtm/bugs: XFAIL UNALIGNED_LOAD_STORE_WRITE
...
- Added option for per CPU threads to the hwlat tracer
- Have hwlat tracer handle hotplug CPUs
- New tracer: osnoise, that detects latency caused by interrupts, softirqs
and scheduling of other tasks.
- Added timerlat tracer that creates a thread and measures in detail what
sources of latency it has for wake ups.
- Removed the "success" field of the sched_wakeup trace event.
This has been hardcoded as "1" since 2015, no tooling should be looking
at it now. If one exists, we can revert this commit, fix that tool and
try to remove it again in the future.
- tgid mapping fixed to handle more than PID_MAX_DEFAULT pids/tgids.
- New boot command line option "tp_printk_stop", as tp_printk causes trace
events to write to console. When user space starts, this can easily live
lock the system. Having a boot option to stop just after boot up is
useful to prevent that from happening.
- Have ftrace_dump_on_oops boot command line option take numbers that match
the numbers shown in /proc/sys/kernel/ftrace_dump_on_oops.
- Bootconfig clean ups, fixes and enhancements.
- New ktest script that tests bootconfig options.
- Add tracepoint_probe_register_may_exist() to register a tracepoint
without triggering a WARN*() if it already exists. BPF has a path from
user space that can do this. All other paths are considered a bug.
- Small clean ups and fixes
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYN8YPhQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qhxLAP9Mo5hHv7Hg6W7Ddv77rThm+qclsMR/
yW0P+eJpMm4+xAD8Cq03oE1DimPK+9WZBKU5rSqAkqG6CjgDRw6NlIszzQQ=
=WEPR
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Added option for per CPU threads to the hwlat tracer
- Have hwlat tracer handle hotplug CPUs
- New tracer: osnoise, that detects latency caused by interrupts,
softirqs and scheduling of other tasks.
- Added timerlat tracer that creates a thread and measures in detail
what sources of latency it has for wake ups.
- Removed the "success" field of the sched_wakeup trace event. This has
been hardcoded as "1" since 2015, no tooling should be looking at it
now. If one exists, we can revert this commit, fix that tool and try
to remove it again in the future.
- tgid mapping fixed to handle more than PID_MAX_DEFAULT pids/tgids.
- New boot command line option "tp_printk_stop", as tp_printk causes
trace events to write to console. When user space starts, this can
easily live lock the system. Having a boot option to stop just after
boot up is useful to prevent that from happening.
- Have ftrace_dump_on_oops boot command line option take numbers that
match the numbers shown in /proc/sys/kernel/ftrace_dump_on_oops.
- Bootconfig clean ups, fixes and enhancements.
- New ktest script that tests bootconfig options.
- Add tracepoint_probe_register_may_exist() to register a tracepoint
without triggering a WARN*() if it already exists. BPF has a path
from user space that can do this. All other paths are considered a
bug.
- Small clean ups and fixes
* tag 'trace-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (49 commits)
tracing: Resize tgid_map to pid_max, not PID_MAX_DEFAULT
tracing: Simplify & fix saved_tgids logic
treewide: Add missing semicolons to __assign_str uses
tracing: Change variable type as bool for clean-up
trace/timerlat: Fix indentation on timerlat_main()
trace/osnoise: Make 'noise' variable s64 in run_osnoise()
tracepoint: Add tracepoint_probe_register_may_exist() for BPF tracing
tracing: Fix spelling in osnoise tracer "interferences" -> "interference"
Documentation: Fix a typo on trace/osnoise-tracer
trace/osnoise: Fix return value on osnoise_init_hotplug_support
trace/osnoise: Make interval u64 on osnoise_main
trace/osnoise: Fix 'no previous prototype' warnings
tracing: Have osnoise_main() add a quiescent state for task rcu
seq_buf: Make trace_seq_putmem_hex() support data longer than 8
seq_buf: Fix overflow in seq_buf_putmem_hex()
trace/osnoise: Support hotplug operations
trace/hwlat: Support hotplug operations
trace/hwlat: Protect kdata->kthread with get/put_online_cpus
trace: Add timerlat tracer
trace: Add osnoise tracer
...
Merge more updates from Andrew Morton:
"190 patches.
Subsystems affected by this patch series: mm (hugetlb, userfaultfd,
vmscan, kconfig, proc, z3fold, zbud, ras, mempolicy, memblock,
migration, thp, nommu, kconfig, madvise, memory-hotplug, zswap,
zsmalloc, zram, cleanups, kfence, and hmm), procfs, sysctl, misc,
core-kernel, lib, lz4, checkpatch, init, kprobes, nilfs2, hfs,
signals, exec, kcov, selftests, compress/decompress, and ipc"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (190 commits)
ipc/util.c: use binary search for max_idx
ipc/sem.c: use READ_ONCE()/WRITE_ONCE() for use_global_lock
ipc: use kmalloc for msg_queue and shmid_kernel
ipc sem: use kvmalloc for sem_undo allocation
lib/decompressors: remove set but not used variabled 'level'
selftests/vm/pkeys: exercise x86 XSAVE init state
selftests/vm/pkeys: refill shadow register after implicit kernel write
selftests/vm/pkeys: handle negative sys_pkey_alloc() return code
selftests/vm/pkeys: fix alloc_random_pkey() to make it really, really random
kcov: add __no_sanitize_coverage to fix noinstr for all architectures
exec: remove checks in __register_bimfmt()
x86: signal: don't do sas_ss_reset() until we are certain that sigframe won't be abandoned
hfsplus: report create_date to kstat.btime
hfsplus: remove unnecessary oom message
nilfs2: remove redundant continue statement in a while-loop
kprobes: remove duplicated strong free_insn_page in x86 and s390
init: print out unknown kernel parameters
checkpatch: do not complain about positive return values starting with EPOLL
checkpatch: improve the indented label test
checkpatch: scripts/spdxcheck.py now requires python3
...
kernel.h is being used as a dump for all kinds of stuff for a long time.
Here is the attempt to start cleaning it up by splitting out panic and
oops helpers.
There are several purposes of doing this:
- dropping dependency in bug.h
- dropping a loop by moving out panic_notifier.h
- unload kernel.h from something which has its own domain
At the same time convert users tree-wide to use new headers, although for
the time being include new header back to kernel.h to avoid twisted
indirected includes for existing users.
[akpm@linux-foundation.org: thread_info.h needs limits.h]
[andriy.shevchenko@linux.intel.com: ia64 fix]
Link: https://lkml.kernel.org/r/20210520130557.55277-1-andriy.shevchenko@linux.intel.com
Link: https://lkml.kernel.org/r/20210511074137.33666-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to append device id even if eeprom have a label property set as some
platform can have multiple eeproms with same label and we can not register
each of those with same label. Failing to register those eeproms trigger
cascade failures on such platform (system is no longer working).
This fix regression on such platform introduced with 4e302c3b56
Reported-by: Alexander Fomichev <fomichev.ru@gmail.com>
Fixes: 4e302c3b56 ("misc: eeprom: at24: fix NVMEM name with custom AT24 device name")
Cc: stable@vger.kernel.org
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The __assign_str macro has an unusual ending semicolon but the vast
majority of uses of the macro already have semicolon termination.
$ git grep -P '\b__assign_str\b' | wc -l
551
$ git grep -P '\b__assign_str\b.*;' | wc -l
480
Add semicolons to the __assign_str() uses without semicolon termination
and all the other uses without semicolon termination via additional defines
that are equivalent to __assign_str() with the eventual goal of removing
the semicolon from the __assign_str() macro definition.
Link: https://lore.kernel.org/lkml/1e068d21106bb6db05b735b4916bb420e6c9842a.camel@perches.com/
Link: https://lkml.kernel.org/r/48a056adabd8f70444475352f617914cef504a45.camel@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Merge misc updates from Andrew Morton:
"191 patches.
Subsystems affected by this patch series: kthread, ia64, scripts,
ntfs, squashfs, ocfs2, kernel/watchdog, and mm (gup, pagealloc, slab,
slub, kmemleak, dax, debug, pagecache, gup, swap, memcg, pagemap,
mprotect, bootmem, dma, tracing, vmalloc, kasan, initialization,
pagealloc, and memory-failure)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (191 commits)
mm,hwpoison: make get_hwpoison_page() call get_any_page()
mm,hwpoison: send SIGBUS with error virutal address
mm/page_alloc: split pcp->high across all online CPUs for cpuless nodes
mm/page_alloc: allow high-order pages to be stored on the per-cpu lists
mm: replace CONFIG_FLAT_NODE_MEM_MAP with CONFIG_FLATMEM
mm: replace CONFIG_NEED_MULTIPLE_NODES with CONFIG_NUMA
docs: remove description of DISCONTIGMEM
arch, mm: remove stale mentions of DISCONIGMEM
mm: remove CONFIG_DISCONTIGMEM
m68k: remove support for DISCONTIGMEM
arc: remove support for DISCONTIGMEM
arc: update comment about HIGHMEM implementation
alpha: remove DISCONTIGMEM and NUMA
mm/page_alloc: move free_the_page
mm/page_alloc: fix counting of managed_pages
mm/page_alloc: improve memmap_pages dbg msg
mm: drop SECTION_SHIFT in code comments
mm/page_alloc: introduce vm.percpu_pagelist_high_fraction
mm/page_alloc: limit the number of pages on PCP lists when reclaim is active
mm/page_alloc: scale the number of pages that are batch freed
...
Use vma_lookup() to find the VMA at a specific address. As vma_lookup()
will return NULL if the address is not within any VMA, the start address
no longer needs to be validated.
Link: https://lkml.kernel.org/r/20210521174745.2219620-16-Liam.Howlett@Oracle.com
Signed-off-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Optimise SVE switching for CPUs with 128-bit implementations.
- Fix output format from SVE selftest.
- Add support for versions v1.2 and 1.3 of the SMC calling convention.
- Allow Pointer Authentication to be configured independently for
kernel and userspace.
- PMU driver cleanups for managing IRQ affinity and exposing event
attributes via sysfs.
- KASAN optimisations for both hardware tagging (MTE) and out-of-line
software tagging implementations.
- Relax frame record alignment requirements to facilitate 8-byte
alignment with KASAN and Clang.
- Cleanup of page-table definitions and removal of unused memory types.
- Reduction of ARCH_DMA_MINALIGN back to 64 bytes.
- Refactoring of our instruction decoding routines and addition of some
missing encodings.
- Move entry code moved into C and hardened against harmful compiler
instrumentation.
- Update booting requirements for the FEAT_HCX feature, added to v8.7
of the architecture.
- Fix resume from idle when pNMI is being used.
- Additional CPU sanity checks for MTE and preparatory changes for
systems where not all of the CPUs support 32-bit EL0.
- Update our kernel string routines to the latest Cortex Strings
implementation.
- Big cleanup of our cache maintenance routines, which were confusingly
named and inconsistent in their implementations.
- Tweak linker flags so that GDB can understand vmlinux when using RELR
relocations.
- Boot path cleanups to enable early initialisation of per-cpu
operations needed by KCSAN.
- Non-critical fixes and miscellaneous cleanup.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAmDUh1YQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNDaUCAC+2Jy2Yopd94uBPYajGybM0rqCUgE7b5n1
A7UzmQ6fia2hwqCPmxGG+sRabovwN7C1bKrUCc03RIbErIa7wum1edeyqmF/Aw44
DUDY1MAOSZaFmX8L62QCvxG1hfdLPtGmHMd1hdXvxYK7PCaigEFnzbLRWTtgE+Ok
JhdvNfsoeITJObHnvYPF3rV3NAbyYni9aNJ5AC/qb3dlf6XigEraXaMj29XHKfwc
+vmn+25oqFkLHyFeguqIoK+vUQAy/8TjFfjX83eN3LZknNhDJgWS1Iq1Nm+Vxt62
RvDUUecWJjAooCWgmil6pt0enI+q6E8LcX3A3cWWrM6psbxnYzkU
=I6KS
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"There's a reasonable amount here and the juicy details are all below.
It's worth noting that the MTE/KASAN changes strayed outside of our
usual directories due to core mm changes and some associated changes
to some other architectures; Andrew asked for us to carry these [1]
rather that take them via the -mm tree.
Summary:
- Optimise SVE switching for CPUs with 128-bit implementations.
- Fix output format from SVE selftest.
- Add support for versions v1.2 and 1.3 of the SMC calling
convention.
- Allow Pointer Authentication to be configured independently for
kernel and userspace.
- PMU driver cleanups for managing IRQ affinity and exposing event
attributes via sysfs.
- KASAN optimisations for both hardware tagging (MTE) and out-of-line
software tagging implementations.
- Relax frame record alignment requirements to facilitate 8-byte
alignment with KASAN and Clang.
- Cleanup of page-table definitions and removal of unused memory
types.
- Reduction of ARCH_DMA_MINALIGN back to 64 bytes.
- Refactoring of our instruction decoding routines and addition of
some missing encodings.
- Move entry code moved into C and hardened against harmful compiler
instrumentation.
- Update booting requirements for the FEAT_HCX feature, added to v8.7
of the architecture.
- Fix resume from idle when pNMI is being used.
- Additional CPU sanity checks for MTE and preparatory changes for
systems where not all of the CPUs support 32-bit EL0.
- Update our kernel string routines to the latest Cortex Strings
implementation.
- Big cleanup of our cache maintenance routines, which were
confusingly named and inconsistent in their implementations.
- Tweak linker flags so that GDB can understand vmlinux when using
RELR relocations.
- Boot path cleanups to enable early initialisation of per-cpu
operations needed by KCSAN.
- Non-critical fixes and miscellaneous cleanup"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (150 commits)
arm64: tlb: fix the TTL value of tlb_get_level
arm64: Restrict undef hook for cpufeature registers
arm64/mm: Rename ARM64_SWAPPER_USES_SECTION_MAPS
arm64: insn: avoid circular include dependency
arm64: smp: Bump debugging information print down to KERN_DEBUG
drivers/perf: fix the missed ida_simple_remove() in ddr_perf_probe()
perf/arm-cmn: Fix invalid pointer when access dtc object sharing the same IRQ number
arm64: suspend: Use cpuidle context helpers in cpu_suspend()
PSCI: Use cpuidle context helpers in psci_cpu_suspend_enter()
arm64: Convert cpu_do_idle() to using cpuidle context helpers
arm64: Add cpuidle context save/restore helpers
arm64: head: fix code comments in set_cpu_boot_mode_flag
arm64: mm: drop unused __pa(__idmap_text_start)
arm64: mm: fix the count comments in compute_indices
arm64/mm: Fix ttbr0 values stored in struct thread_info for software-pan
arm64: mm: Pass original fault address to handle_mm_fault()
arm64/mm: Drop SECTION_[SHIFT|SIZE|MASK]
arm64/mm: Use CONT_PMD_SHIFT for ARM64_MEMSTART_SHIFT
arm64/mm: Drop SWAPPER_INIT_MAP_SIZE
arm64: Conditionally configure PTR_AUTH key of the kernel.
...
Add SLAB and page allocator tests for init_on_alloc. Testing for
init_on_free was already happening via the poisoning tests.
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210623203936.3151093-10-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For various failure conditions, try to include some details about where
to look for reasons about the failure.
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210623203936.3151093-8-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Where feasible, I prefer to have all tests visible on all architectures,
but to have them wired to XFAIL. DOUBLE_FAIL was set up to XFAIL, but
wasn't actually being added to the test list.
Fixes: cea23efb4d ("lkdtm/bugs: Make double-fault test always available")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210623203936.3151093-7-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to the existing slab overflow and stack exhaustion tests, add
VMALLOC_LINEAR_OVERFLOW (and rename the slab test SLAB_LINEAR_OVERFLOW).
Additionally unmarks the test as destructive. (It should be safe in the
face of misbehavior.)
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210623203936.3151093-6-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mei extension header was build as array of flexible structures
which will not work if actually more headers are added.
(Currently only vtag header was used).
Sparse reports:
drivers/misc/mei/hw.h:253:32: warning: array of flexible structures
Use basic type u8 for the variable sized extension.
Define explicitly mei_ext_hdr_vtag structure.
And also fix mei_ext_next() function to point correctly to the
end of the header.
Note: the headers are part of firmware interface and need to be __packed.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20210621193756.134027-2-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Over time the functions were renamed,
but this was not always reflected in kdoc, fix that.
Signed-off-by: Tamar Mashiah <tamar.mashiah@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20210621193756.134027-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is code related to hard-reset, which is done in gaudi specific
code. However, this code can be used by future ASICs and therefore it
is better to move it to the common code section.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We add support for NIC DERR ECC error events, in case this error
is received a device reset will be performed.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In preparation for a new feature that allows the user to reserve
signals ahead of submissions, we need to change a current assumption
in the code.
Currently, the driver uses 2 SOBs to support signal CS. When the first
SOB reaches max value, the driver switches to the other one and assumes
that when it will need to switch back to the first one, all of the
signals have already been handled.
This assumption won't hold when the new feature will be added, because
using signal reservation, the driver can reach the max SOB value very
fast.
The change is to add a validity check when submitting a signal CS, to
make sure the previous SOB is available (all the signals attached to
it indeed finished).
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
We introduce a new type of reset which is reset upon device release.
This reset is very similar to soft reset except the fact it is
performed only upon device release and not upon user sysfs request
nor TDR.
The purpose of this reset is to make sure the device is returned to
IDLE state after the current user has finished working with the device.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
To be able to debug long-running CS better, without changing the
userspace code, we are adding a new option through debugfs interface
to skip the reset of the device in case of CS timeout.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Currently driver sends fc interrupt id to FW instead of using
cpu interrupt id. We intend to fix that and keep backward
compatibility by using the same interrupt values.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There was a rogue #ifdef that crept into the upstream code for
backwards compatibility which isn't needed of course.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case QMAN has an error and stop_on_err is true, print specific
information of the "offending" command buffer batch.
If the error occurred on one of the higher CPs, the CQ pointer and size
will be printed along with (up to) last 8 PQEs of the stream.
If the error occurred in the lower CP, the CQ pointer and size will be
printed along with (up to) last 8 PQEs of ALL upper CPs as we have no
way to know which upper CP sent the job there.
This is done so higher SW levels will be able to debug their CS by
extracting the raw data of the offending command buffer batch and
examine those offline to detect the issue.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In a system with multiple ASICs, there is a need to provide monitoring
tools with information on how long a device was opened and how many
times a device was opened.
Therefore, we add a new opcode to the INFO ioctl to provide that
information.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Update STMTCSR and STMSYNCR values in order to reduce amount of sync
packets
Signed-off-by: Tal Albo <talbo@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
fix the following smatch warnings:
goya_pin_memory_before_cs()
warn: '&userptr->job_node' not removed from list
gaudi_pin_memory_before_cs()
warn: '&userptr->job_node' not removed from list
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
pin_user_pages_fast() might fail and return a negative number, or pin
less pages than requested and return the number of the pages that were
pinned.
For the latter, it is informative to print also the memory size and the
number of requested pages.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 2e5eda4681 ("habanalabs: PCIe Advanced Error Reporting support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Firmware in habanalabs devices is composed of several components.
During device initialization, we read these versions from the device.
Print them during device initialization to allow better visibility in
automated systems.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Hard reset flow on PLDM might take more than 2 minutes.
Hence add a dedicated hard reset timeout of 6 minutes for PLDM.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In current code, for dynamic f/w loading flow, DRAM scrambling is
enabled post Linux fit image is loaded to the card. This can cause the
device CPU to go into reset state.
The correct sequence should be:
1. Load boot fit image
2. Enable scrambling
3. Load Linux fit image
This commit aligns the DRAM scrambling enabling with the static f/w load
flow.
Signed-off-by: Bharat Jauhari <bjauhari@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
If there is an error in the QMAN/engine, there is no point of trying
to continue running the workload. It is better to stop to allow the
user to debug the program.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In case we have EQ fault we would like to know about it.
For this, a status bitmask was added in which EQ_FAULT bit is
set by FW in case of EQ fault.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When there is an ECC error in the HBM, return a standard error code,
-EIO in this case, and not a positive value.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When converting virtual address to physical we need to add correct
offset to the physical page.
For this we need to use mask that include ALL bits of page offset.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Get rid of the need to check if boot_dev_sts is valid on every access
to value read from these registers.
This is done by storing the register value in hdev props ONLY if
register is enabled.
This way if register is NOT enabled all capability bits will not be set.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
If device is not idle after user closes the FD we must reset device
as next user that will try to open FD will encounter a non-functional
device.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Sometimes it is useful to allow the command to continue running despite
the timeout occurred, to differentiate between really stuck or just very
time consuming commands. This can be achieved by passing a new debug
flag alongside the cs, HL_CS_FLAGS_SKIP_RESET_ON_TIMEOUT.
Anyway, if the timeout occurred, a warning print shall be issued,
however this shall not fail the submission.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order for driver to be aware of process or thread crashes inside
GAUDI's CPU, we introduce a new event which contains all relevant
information. Upon event reception, driver will dump information and
will reset the device.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In the collective wait, we put jobs on the QMANs of all the NICs. The
code takes into account if a port is disabled only in case of PCI card.
When this info arrives from the f/w, the code doesn't take it into
account, and it tries to schedule jobs on NICs that aren't enabled and
thats a bug.
To fix this, after the f/w sends us the list of disabled ports, we
update the state of the QMANs according to that list. In addition,
we need to update the HW_CAP bits so the collective wait operation
will not try to use those QMANs. We also need to update the collective
master monitor mask.
Moreover, we need to add a protection for such future cases and in case
the user will try to submit work to those QMANs.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Current implementation uses a single interrupt interface towards
FW, this interface is causing races between interrupt types.
We split this interface to interface per interrupt type.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There is no dependency when probing multiple devices so indicate to the
kernel that it can probe our devices in ASYNC fashion.
This shortens insmod of the driver from ~2 minutes to 20 seconds on
a system with 8 devices.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Update the QM stop on error masks to also stop on ARB errors.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
nic_ports_mask is used by the networking part of the driver.
In the compute part, we use the HW_CAP bits to select what is active
and what is not.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This fix was applied since there was an incorrect reported CPU ID to GIC
such that an error in MME2 QMAN aliased to be an arriving from DMA0_QM.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
After all the latest changes to the reset code, there were some
redundancy and errors in the flows.
If the Linux FIT is loaded to the ASIC CPU, we need to communicate
with it only via GIC. If it is not loaded, we need to either use
COMMS protocol (for newer f/w) or MSG_TO_CPU register (for older f/w).
In addition, if we halted the device CPU then we need to mark that
the driver will do the reset, regardless of the capabilities.
Also, to prevent false errors, we need to keep track whether the
device CPU was already halted. If so, we shouldn't try to halt it
again.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Using negative logic (i.e. fw_security_disabled) is confusing.
Modify the flag to use positive logic (fw_security_enabled).
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This is needed because legacy FW 'communication' protocol will soon
become obsolete.
Because COMMS is a boot protocol, communicating through it is supported
only until Linux is loaded to the device CPU, where in that case we
will fallback to the former implementation.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Security is set based on PCI ID, and after reading preboot status bits.
GIC usage is set in both scenarios since GIC can't be used when security
is enabled.
Moreover, writing to GIC/SP is enabled only after Linux is fully loaded.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
On newer releases, host won't be able to trigger an interrupt directly
to the ASIC GIC controller.
To be able to decide whether GIC can/not be used, we must read device's
preboot status bits in a stage that precedes the possible first use of
GIC (when device is in dirty state).
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
To harden the event queue mechanism, we add a running index to the
control header of the entry.
The firmware writes the index in each entry and the driver verifies
that the index of the current entry is larger by 1 of the index of
the previous entry.
In case it isn't, the driver will treat the entry as if it wasn't
valid (it won't process it but won't skip it).
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Scrubbing memory after every unmap is very costly in terms of
performance. If a user wants it he can enable it but the default
should prioritize performance.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
As iATU configuration is done by FW, driver should not try and
move HBM bar.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reading of GIC privileged status will be done after F/W is loaded,
because privileged GIC capability is only available with the correct
ARMCP version, and after it's loaded.
Such versions necessarily support COMMS, so GIC alternatives (SP regs)
will be read directly from dynamic regs.
As well, initiation of DMA QMANs will occur after F/W is loaded
since it depends on GIC configuration.
In case F/W isn't loaded there's no problem since either way
there won't be any GIC IRQ handling.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Fix issue in which the input to the function is_asic_secured was device
PCI_IDS number instead of the asic_type enumeration.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
LKD should provide hard reset cause to preboot prior to
loading any FW components (in case needed).
Current implementation is based on the new FW 'COMMS' protocol
In cased 'COMMS' is disabled - reset cause won't be sent.
Currently, only 2 reset causes are shared: HEARTBEAT & TDR.
Sending the reset cause will provide the missing watchdog
info that the firmware needs to provide to the BMC.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
An information print notifying on starting to load the f/w was removed
by mistake when moving to the new dynamic f/w loading mechanism.
Restore that print as the F/W loading usually takes between 10 to 20
seconds and this print helps the user know the status of the driver
load.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Due to new security restrictions, GIC controller can no
longer be accessed from user/kernel.
To monitor that, a new status bit will be read from preboot
caps, indicating whether direct access to GIC is blocked.
In case it is blocked, driver will use scratchpad registers
instead of using GIC interface on two main scenarios:
The first of which LKD triggers interrupts to F/W through GIC,
and the second of when LKD configures all engines/QMANs
to write to GIC when they want to report an error.
From F/W perspective, it will poll on all SPs, and once IRQ
number is retrieved, SP register is cleared, and it will perform the
write to the GIC to trigger the IRQ handler.
Signed-off-by: Koby Elbaz <kelbaz@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Maintain both STS1 and ERR1 registers used for status communication
with F/W.
Those are not maintained as we currently have less than 31
statuses/error defined and so LKD did not refer to those register.
The reason to read them now is to try to support future f/w versions
with current driver.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When attempting to read FW component's version we should break if input
FW component is invalid in order to avoid using uninitialized
destination pointer.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When setting "DMA mask from FW" we are reading PSOC_GLOBAL_CONF register
which is allowed only once FW has done it's iATU configuration.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Some users might want to implement their own policy of when the device
is unusable so we need to ignore this status in the driver and continue
loading as normal.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Implementing dynamic linux image load to the device.
This patch also implements the FW communication steps during the
boot-fit.
This patch also enables the dynamic protocol based on the compatibility
flag.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Implementing dynamic boot fit image load to the device.
Note that some necessary adjustment were added to the static loader as
well so that both loaders can co-exist.
as this is not the final FW load stage the dynamic FW load is still
forced to be non functional.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Hint address failure that results in a valid mapping with an address
that was allocated by the driver is not a real failure.
Therefore, the driver shouldn't notify about this in kernel log. The
user is responsible to check the returned address.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Indicate "progress" instead of "error" when reporting progress status.
Change "u-boot stopped by user" to "Cannot boot" message as
CPU_BOOT_STATUS_UBOOT_NOT_READY may indicate a fatal error that prevent
u-boot from loading firmware.
Signed-off-by: Guy Nisan <gnisan@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
iATU (internal Address Translation Unit of the PCI controller)
configuration is being done by FW right after driver enables
the PCI device. Hence, driver must add a minor sleep afterwards
in order to make sure FW finishes configuring iATU regions.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Update the common and GAUDI firmware header files to the latest version.
The latest version use the correct endianness types so this commit also
contains minor changes to the code to use the correct conversions when
reading/writing to the firmware structures.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
LKD has interfaces in which it receives device address.
For instance the debugfs_read/write variants receives device address for
CFG/SRAM/DRAM for read/write and need to translate to the mapped PCI BAR
address.
In addition, the dynamic FW load protocol dictates that the address to
which the LKD will copy the image for the next FW component will be
received as a device address and can be placed either in SRAM or DRAM.
We need to distinguish those regions as the access methods to those
regions are different (in DRAM we possibly need to set the BAR base).
Looking forward this code will be used to remove duplicated code in the
debugfs_read/write that search the memory region for the input device
address.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
First stage of the dynamic FW load protocol is to reset the protocol to
avoid residues from former load cycles.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Instead of using multiple ASIC specific copies of functions to read the
FW version use single common one that gets ASIC specific arguments.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Use mmu cache range invalidation instead of entire cache invalidation
because it yields better performance.
In GOYA and GAUDI, always use entire cache invalidation because these
ASICs don't support range invalidation.
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Replace multiple arguments to init device CPU function by passing
firmware loader managing structure that is initialized per ASIC with
the loader parameters.
In addition, the FW loader management structure is now part of the
habanalabs device, this way the loader parameters will be able to be
communicated across various boot stages.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
This refactor is needed due to the dynamic FW load in which requesting
the FW file (and getting its attributes) is not immediately followed by
copying FW file content.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Start the skeleton for the dynamic F/W load by marking current preboot
code path as legacy.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
On PLDM, in case of NIC hangs, the ELBI reset to take much longer than
expected. As a result an increase in the ELBI reset timeout is required.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
checkpatch looks for the tag on the first line.
So delete empty first line
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20210610214438.3161140-4-trix@redhat.com
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add the ARM64_PTR_AUTH_KERNEL config and deals with the
build aspect of it.
Userspace support has no dependency on the toolchain therefore all
toolchain checks and build flags are controlled the new config
option.
The default config behavior will not be changed.
Signed-off-by: Daniel Kiss <daniel.kiss@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210613092632.93591-2-daniel.kiss@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into tty-next
We want the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into driver-core-next
We need the driver core fix in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into char-misc-next
We need the fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes:
drivers/misc/eeprom/at25.c:181:28: warning: field width should have type 'int', but argument has type 'unsigned long'
drivers/misc/eeprom/at25.c:386:13: warning: cast to smaller integer type 'int' from 'const void *'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Fixes: fd307a4ad3 ("nvmem: prepare basics for FRAM support")
Link: https://lore.kernel.org/r/20210611142706.27336-1-jiri.prchal@aksignal.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added enum and string for FRAM (ferroelectric RAM) to expose it as file
named "fram".
Added documentation of sysfs file.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Link: https://lore.kernel.org/r/20210611094601.95131-2-jiri.prchal@aksignal.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
aspm (Active State Power Management)
rtsx_comm_set_aspm: this function is for driver to make sure
not enter power saving when processing of init and card_detcct
ASPM_MODE_CFG: 8411 5209 5227 5229 5249 5250
Change back to use original way to control aspm
ASPM_MODE_REG: 5227A 524A 5250A 5260 5261 5228
Keep the new way to control aspm
Fixes: 121e9c6b5c ("misc: rtsx: modify and fix init_hw function")
Reported-by: Chris Chiu <chris.chiu@canonical.com>
Tested-by: Gordon Lack <gordon.lack@dsl.pipex.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20210607101634.4948-1-ricky_wu@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When iterating over child firmware nodes restore printing the name of ones
that are not supported.
While at it, refactor loop body to clearly show that we stop at the first match.
Fixes: db15d73e5f ("eeprom: idt_89hpesx: Support both ACPI and OF probing")
Cc: Huy Duong <qhuyduong@hotmail.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210607221757.81465-2-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_get_next_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
Fixes: db15d73e5f ("eeprom: idt_89hpesx: Support both ACPI and OF probing")
Cc: Huy Duong <qhuyduong@hotmail.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210607221757.81465-1-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using list_move_tail() instead of list_del() + list_add_tail() in bcm_vk_msg.c.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Link: https://lore.kernel.org/r/20210609071430.1337400-1-libaokun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable err is being assigned a value that is never read, the
assignment is redundant and can be removed. Also remove some empty
lines.
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210603131210.84763-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'pvpanic_remove()' is referenced only by a 'devm_add_action_or_reset()'
call in 'devm_pvpanic_probe()'. So, we know that its parameter is non-NULL.
Axe the unneeded check to save a few lines of code.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/8e425618f4042a8ab8366be4d34026972e77bd40.1622911768.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from iLO ASIC 'Neches' with subsystem device id 0x00E4,
bar 5 is used for shared memory region mapping instead of bar 2
because bar 2 is made inaccessible after system POST for security
reason.
As this holds true for future iLO ASIC generations, it does not
make sense to map shared memory region according to the subsystem
device id of each following generations.
Map iLO shared memory region with PCI revision id that maps to the
iLO ASIC generation, starting from Neches (Rev 7).
Signed-off-by: Matt Hsiao <matt.hsiao@hpe.com>
Link: https://lore.kernel.org/r/20210531085551.26421-1-matt.hsiao@hpe.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some tiny char/misc driver fixes for 5.13-rc4.
Nothing huge here, just some tiny fixes for reported issues:
- 2 interconnect driver fixes
- kgdb build warning fix for gcc-11
- hgafb regression fix
- soundwire driver fix
- mei driver fix
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYLJIxQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykGCgCfX/NsOhFfGDwuLB1cdvCbz7yAy0wAn2RkpPEd
rvLlnmp4+mAxDXmBsAqP
=cgtc
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some tiny char/misc driver fixes for 5.13-rc4.
Nothing huge here, just some tiny fixes for reported issues:
- two interconnect driver fixes
- kgdb build warning fix for gcc-11
- hgafb regression fix
- soundwire driver fix
- mei driver fix
All have been in linux-next with no reported issues"
* tag 'char-misc-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: request autosuspend after sending rx flow control
kgdb: fix gcc-11 warnings harder
video: hgafb: correctly handle card detect failure during probe
soundwire: qcom: fix handling of qcom,ports-block-pack-mode
interconnect: qcom: Add missing MODULE_DEVICE_TABLE
interconnect: qcom: bcm-voter: add a missing of_node_put()
Since the macro was introduced in 2019 (commit bb6243b4f7 ("drivers:
platform: provide devm_platform_ioremap_resource_wc()") there is only a
single user which hardly justifies the function for the small task it
provides.
So drop the helper and open-code it in the only user. Adapt the non-wc
case accordingly.
For a all-mod-config build on amd64 this change introduces the following
changes according to bloat-o-meter:
add/remove: 0/1 grow/shrink: 1/0 up/down: 20/-252 (-232)
Function old new delta
devm_platform_ioremap_resource_wc 252 - -252
sram_probe 796 816 +20
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210525103711.956438-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A rx flow control waiting in the control queue may block autosuspend.
Re-request autosuspend after flow control been sent to unblock
the transition to the low power state.
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20210526193334.445759-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving the call to ee1004_set_current_page() to ee1004_eeprom_read()
allows to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/2829a131-51e3-8865-462a-564080158b0b@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value of ee1004_current_page applies to all SPD eeproms connected
to the adapter. Therefore it's sufficient if we set ee1004_current_page
when the first device is added.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/b9240e58-08bb-3d71-7a9c-9a323b470ab6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c_new_dummy_device() calls i2c_new_client_device() that complains
if it fails to create the device. Therefore we don't have to emit an
error message in case of failure. In addition ensure that
ee1004_set_page is only set if creating the device succeeded.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/d38df5ac-6ecb-7d5f-b5c3-39bfc6a1e8a1@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have to read 512 bytes only, therefore read performance isn't really
a concern. Don't bother the user if i2c block read isn't supported.
For i2c_smbus_read_i2c_block_data_or_emulated() to work it's sufficient
if I2C_FUNC_SMBUS_READ_I2C_BLOCK or I2C_FUNC_SMBUS_READ_BYTE_DATA is
supported. Therefore remove the check for I2C_FUNC_SMBUS_READ_WORD_DATA.
In addition check for I2C_FUNC_SMBUS_WRITE_BYTE (included in
I2C_FUNC_SMBUS_BYTE) which is needed for setting the page.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/840c668e-6310-e933-e50e-5abeaecfb39c@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c_smbus_read_i2c_block_data_or_emulated() checks its length argument,
so we don't have to do it. In addition remove the unlikely hint from
the checks, we do i2c reads and therefore are in a slow path.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/eb2a8bff-43ec-c763-a417-9d741e6f0034@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sysfs_kf_bin_read() checks this for us already. In addition
the function works correctly also w/o this check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/33889bff-3614-4b73-5010-701635e1edab@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify code and turn 'pvpanic_probe()' into a managed resource version.
This simplify callers that don't need to do some clean-up on error in the
probe and on remove.
Update pvpanic-mmio.c and pvpanic-pci.c accordingly.
'pvpanic_remove()' don't need to be exported anymore.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/9212cdc8c1e5c187a2f1129a6190085c2a10d28a.1621665058.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kees Cook