Add support for the V4L2_PIX_FMT_RGBA444, V4L2_PIX_FMT_RGBX444,
V4L2_PIX_FMT_ABGR444, V4L2_PIX_FMT_XBGR444, V4L2_PIX_FMT_BGRA444 and
V4L2_PIX_FMT_BGRX444 formats to the VSP driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the V4L2_PIX_FMT_BGRA32, V4L2_PIX_FMT_BGRX32,
V4L2_PIX_FMT_RGBA32 and V4L2_PIX_FMT_RGBX32 formats to the VSP driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Amlogic G12A SoC embeds a second CEC controller with a totally
different design.
The two controller can work in the same time since the CEC line can
be set to two different pins on the two controllers.
This second CEC controller is documented as "AO-CEC-B", thus the
registers will be named "CECB_" to differentiate with the other
AO-CEC driver.
Unlike the other AO-CEC controller, this one takes the Oscillator
clock as input and embeds a dual-divider to provide a precise
32768Hz clock for communication. This is handled by registering
a clock in the driver.
Unlike the other AO-CEC controller, this controller supports setting
up to 15 logical addresses and supports the signal_free_time settings
in the transmit function.
Unfortunately, this controller does not support "monitor" mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CrosEC CEC driver never decremented the HDMI device refcount.
CEC drivers only need the HDMI device pointer as a key in the
notifier list, it never accesses the device, so there is no
need to keep a reference.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The SECO CEC driver never decremented the HDMI device refcount.
CEC drivers only need the HDMI device pointer as a key in the
notifier list, it never accesses the device, so there is no
need to keep a reference.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Tegra CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The STI CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The S5P CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The meson CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add helper function to parse the DT for the hdmi-phandle property
and return the corresponding struct device pointer.
It takes care to avoid increasing the device refcount since all
we need is the device pointer. This pointer is used in the
notifier list as a key, but it is never accessed by the CEC driver.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Wen Yang <wen.yang99@zte.com.cn>
Acked-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
I previously added an RC_CORE dependency here, but missed the corner
case of CONFIG_VIDEO_SECO_CEC=y with CONFIG_RC_CORE=m, which still
causes a link error:
drivers/media/platform/seco-cec/seco-cec.o: In function `secocec_probe':
seco-cec.c:(.text+0x1b8): undefined reference to `devm_rc_allocate_device'
seco-cec.c:(.text+0x2e8): undefined reference to `devm_rc_register_device'
drivers/media/platform/seco-cec/seco-cec.o: In function `secocec_irq_handler':
seco-cec.c:(.text+0xa2c): undefined reference to `rc_keydown'
Refine the dependency to disallow building the RC subdriver in this case.
This is the same logic we apply in other drivers like it.
Fixes: f27dd0ad68 ("media: seco-cec: fix RC_CORE dependency")
Cc: <stable@vger.kernel.org> # 5.1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In function ts2020_set_tuner_rf(), local variable "utmp" could
be uninitialized if function regmap_read() returns -EINVAL.
However, this value is used in if statement and written to
the register, which is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The timestamps in ir-keytable -t output showed that the Xbox DVD
IR dongle decodes scancodes every 64ms. The last scancode of a
longer button press is decodes 64ms after the last-but-one which
indicates the decoder doesn't use a timeout but decodes on the last
edge of the signal.
267.042629: lirc protocol(unknown): scancode = 0xace
267.042665: event type EV_MSC(0x04): scancode = 0xace
267.042665: event type EV_KEY(0x01) key_down: KEY_1(0x0002)
267.042665: event type EV_SYN(0x00).
267.106625: lirc protocol(unknown): scancode = 0xace
267.106643: event type EV_MSC(0x04): scancode = 0xace
267.106643: event type EV_SYN(0x00).
267.170623: lirc protocol(unknown): scancode = 0xace
267.170638: event type EV_MSC(0x04): scancode = 0xace
267.170638: event type EV_SYN(0x00).
267.234621: lirc protocol(unknown): scancode = 0xace
267.234636: event type EV_MSC(0x04): scancode = 0xace
267.234636: event type EV_SYN(0x00).
267.298623: lirc protocol(unknown): scancode = 0xace
267.298638: event type EV_MSC(0x04): scancode = 0xace
267.298638: event type EV_SYN(0x00).
267.543345: event type EV_KEY(0x01) key_down: KEY_1(0x0002)
267.543345: event type EV_SYN(0x00).
267.570015: event type EV_KEY(0x01) key_up: KEY_1(0x0002)
267.570015: event type EV_SYN(0x00).
Add a protocol with the repeat value and set the timeout in the
driver to 10ms (to have a bit of headroom for delays) so the Xbox
DVD remote performs more responsive.
Signed-off-by: Matthias Reichl <hias@horus.com>
Acked-by: Benjamin Valentin <benpicco@googlemail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Later datasheet versions (rev 1.00) clarifies that the FLD register
should be set after LINKCNT.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Latest information from hardware engineers reveals that H3 ES2 and ES3
behave differently when working with link speeds bellow 250 Mpbs.
Add a SoC match for H3 ES2.* and use the correct startup sequence.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The latest datasheet (rev 1.50) updates the start procedure for V3M and
E3. Update the driver to match these changes.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Later versions of the datasheet updates the reset procedure to more
closely resemble the standby mode. Update the driver to enter and exit
the standby mode instead of resetting the hardware before and after
streaming is started and stopped. This replaces the software reset
(SRST.SRST) control.
While at it break out the full start and stop procedures from
rcsi2_s_stream() into the existing helper functions.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If VIDIOC_CREATE_BUFS is called with a sizeimage smaller than the
queue sizeimage, fail with -EINVAL instead of correcting the size
and continuing without error. This is required by v4l2-compliance.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance sets colorimetry on the output queue and then verifies
that querying colorimetry on the capture queue returns the same
configuration. For this to work, the encoder must allow setting context
colorimetry parameters on the output queue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The stateful encoder API requires VIDIOC_ENUM_FRAMESIZES to be
implemented.
Allow enumeration of supported frame sizes for encoding.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Return -ENOTTY when userspace tries to call VIDIOC_(TRY_)ENCODER_CMD on
a decoder instance or VIDIOC_(TRY_)DECODER_CMD on an encoder instance.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add min number of buffers for capture (decoder) and output (encoder)
controls, which are required by the stateful video decoder / encoder
interface specification.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The error return value is not written by some firmware codecs, such as
MPEG-2 decode on CodaHx4. Clear the error return value before starting
the picture run to avoid misinterpreting unrelated values returned by
sequence initialization as error return value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since levels are specified in terms of maximum values, there is no
reason to filter out lower levels than the supported maximum.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The chosen codec depends on the coded format, which is known as soon as
the S_FMT call on the coded queue. This allows to use the codec in
callbacks that may be called before start_streaming, such as buf_queue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Calling VIDIOC_DQBUF can release the core serialization lock pointed to
by vb2_queue->lock if it has to wait for a new buffer to arrive.
However, if userspace dup()ped the video device filehandle, then it is
possible to read or call DQBUF from two filehandles at the same time.
It is also possible to call REQBUFS from one filehandle while the other
is waiting for a buffer. This will remove all the buffers and reallocate
new ones. Removing all the buffers isn't the problem here (that's already
handled correctly by DQBUF), but the reallocating part is: DQBUF isn't
aware that the buffers have changed.
This is fixed by setting a flag whenever the lock is released while waiting
for a buffer to arrive. And checking the flag where needed so we can return
-EBUSY.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Syzbot <syzbot+4180ff9ca6810b06c1e9@syzkaller.appspotmail.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ctrl_check_input() function is called from pvr2_ctrl_range_check().
It's supposed to validate user supplied input and return true or false
depending on whether the input is valid or not. The problem is that
negative shifts or shifts greater than 31 are undefined in C. In
practice with GCC they result in shift wrapping so this function returns
true for some inputs which are not valid and this could result in a
buffer overflow:
drivers/media/usb/pvrusb2/pvrusb2-ctrl.c:205 pvr2_ctrl_get_valname()
warn: uncapped user index 'names[val]'
The cptr->hdw->input_allowed_mask mask is configured in pvr2_hdw_create()
and the highest valid bit is BIT(4).
Fixes: 7fb20fa38c ("V4L/DVB (7299): pvrusb2: Improve logic which handles input choice availability")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
syzkaller reported crashes on kfree() called from
vivid_vid_cap_s_selection(). This looks like a simple typo, as
dev->bitmap_cap is allocated with vzalloc() throughout the file.
Fixes: ef834f7836 ("[media] vivid: add the video capture and output
parts")
Signed-off-by: Alexander Potapenko <glider@google.com>
Reported-by: Syzbot <syzbot+6c0effb5877f6b0344e2@syzkaller.appspotmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If a buffer is queued to a request, followed by an attempt to queue
the same buffer again, then the second qbuf returns an error since
the buffer is not in the DEQUEUED state anymore.
However, before it gets to that check it executes the code under the
'if (!vb->prepared)' condition. This clears previously set data needed
for request handling, and now querybuf will no longer report that this
buffer is part of a request.
Move the state check to before the 'if' and make sure to only do the
state check when called from QBUF and if V4L2_BUF_FLAG_REQUEST_FD is
set.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Update referenced frame buffer's reference count when playing vp9
content which has show_existing_frame flag, and copy enough buffer
data to current shown frame.
Signed-off-by: Maoguang Meng <maoguang.meng@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver returns an error if unsupported media bus pixel code is
requested by VIDIOC_SUBDEV_S_FMT.
But according to Documentation/media/uapi/v4l/vidioc-subdev-g-fmt.rst,
Drivers must not return an error solely because the requested format
doesn't match the device capabilities. They must instead modify the
format to match what the hardware can provide.
So select default format code and return success in that case.
This is detected by v4l2-compliance.
Cc: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Register V4L2 subdevice implemented by the driver to the V4L2
asynchronous subdevice framework.
[Sakari Ailus: Remove extra call to v4l2_i2c_subdev_set_name]
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In preparation for adding asynchronous subdevice support to the driver,
don't acquire v4l2_clk from the driver .probe() callback as that may
fail if the clock is provided by a bridge driver which may be not yet
initialized. Move the v4l2_clk_get() to ov6650_video_probe() helper
which is going to be converted to v4l2_subdev_internal_ops.registered()
callback, executed only when the bridge driver is ready.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
After removal of clock_start() from before soc_camera_init_i2c() in
soc_camera_probe() by commit 9aea470b39 ("[media] soc-camera: switch
I2C subdevice drivers to use v4l2-clk") introduced in v3.11, the ov6650
driver could no longer probe the sensor successfully because its clock
was no longer turned on in advance. The issue was initially worked
around by adding that missing clock_start() equivalent to OMAP1 camera
interface driver - the only user of this sensor - but a propoer fix
should be rather implemented in the sensor driver code itself.
Fix the issue by inserting a delay between the clock is turned on and
the sensor I2C registers are read for the first time.
Tested on Amstrad Delta with now out of tree but still locally
maintained omap1_camera host driver.
Fixes: 9aea470b39 ("[media] soc-camera: switch I2C subdevice drivers to use v4l2-clk")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the application was streaming from both videoX and vbiX, and streaming
from videoX was stopped, then the vbi streaming also stopped.
The cause being that stop_streaming for video stopped the subdevs as well,
instead of only doing that if dev->streaming_users reached 0.
au0828_stop_vbi_streaming was also wrong since it didn't stop the subdevs
at all when dev->streaming_users reached 0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Enable and disable source interfaces aren't consistent in enforcing
how video and audio share the tuner resource.
Fix these issues to enforce the following rules and allow
sharing between audio and video applications.
- When DVB is streaming, audio/video/vbi/s-video/composite
should find the resource busy. DVB holds the tuner in
exclusive mode.
- When video/VBI is streaming, audio can share the tuner and vice versa.
- v4l2 allows multiple applications to open video device.
- Video applications call enable source multiple times during their
run-time. Resource should stay locked until the last application
releases it.
- A shared resource should stay in shared state and locked when it is
in use by audio and video. More than one video application is allowed
to use the tuner as long as video streaming protocol allows such usage.
Resource is released when the last video/audio application releases it.
- S-Video and Composite hold the resource in exclusive mode.
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Media Device Allocator API to allows multiple drivers share a media device.
This API solves a very common use-case for media devices where one physical
device (an USB stick) provides both audio and video. When such media device
exposes a standard USB Audio class, a proprietary Video class, two or more
independent drivers will share a single physical USB bridge. In such cases,
it is necessary to coordinate access to the shared resource.
Using this API, drivers can allocate a media device with the shared struct
device as the key. Once the media device is allocated by a driver, other
drivers can get a reference to it. The media device is released when all
the references are released.
Change au0828 to use Media Device Allocator API to allocate media device
with the parent usb struct device as the key, so it can be shared with the
snd_usb_audio driver.
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Media Device Allocator API to allows multiple drivers share a media device.
This API solves a very common use-case for media devices where one physical
device (an USB stick) provides both audio and video. When such media device
exposes a standard USB Audio class, a proprietary Video class, two or more
independent drivers will share a single physical USB bridge. In such cases,
it is necessary to coordinate access to the shared resource.
Using this API, drivers can allocate a media device with the shared struct
device as the key. Once the media device is allocated by a driver, other
drivers can get a reference to it. The media device is released when all
the references are released.
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Do not access sd_formats[] if num_of_sd_formats is zero, ie
subdev sensor didn't expose any formats.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Report overrun error only when it exceeds a given threshold.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are several places where a break statement occurs before
a following break statement; these are unnecessary and can be
removed to clean up the code a little.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Enlarge the plane number to support more complex case
and add the support for fmt change case.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Media bus codes were being mapped to pixelformats, which causes a
limitation on vimc because not all pixelformats can be mapped to media
bus codes.
Also, media bus codes are an internal configuration from the device.
Userspace only assures media bus codes matches between pads and expects
the image in a given pixelformat. So we can allow almost any media bus
format to be configured between pads, except for debayer that expects a
media bus code of type bayer in the sink pad.
[hverkuil-cisco@xs4all.nl: drop use of v4l2_get_fourcc_name: not yet available]
[hverkuil-cisco@xs4all.nl: made vimc_mbus_list static]
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add bayer format information in struct v4l2_format_info table.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add two new API helpers, v4l2_fill_pixfmt and v4l2_fill_pixfmt_mp,
to be used by drivers to calculate plane sizes and bytes per lines.
Note that driver-specific padding and alignment are not
taken into account, and must be done by drivers using this API.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Minor fix for helper function and comment, s/v4l2_vb2_buffer/vb2_v4l2_buffer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is mandatory to write CEC_CFGR only when CECEN=0. To protect
transmission, a check have been added to delayed logical address
modification. This patch is necessary tp pass all tests of compliance.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ISC will output the "ARGB32" configuration in byte order: B, G, R, Alpha.
This is in fact the format BGRA, aka ABGR32.
If alpha is missing, the same format is equivalent to XBGR32.
Added both formats and removed ARGB32 which is wrong.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This change is a redesign in the formats and the way the ISC is
configured w.r.t. sensor format and the output format from the ISC.
I have changed the splitting between sensor output (which is also ISC input)
and ISC output.
The sensor format represents the way the sensor is configured, and what ISC
is receiving.
The format configuration represents the way ISC is interpreting the data and
formatting the output to the subsystem.
Now it's much easier to figure out what is the ISC configuration for input, and
what is the configuration for output.
The non-raw format can be obtained directly from sensor or it can be done
inside the ISC. The controller format list will include a configuration for
each format.
The old supported formats are still in place, if we want to dump the sensor
format directly to the output, the try format routine will detect and
configure the pipeline accordingly.
This also fixes the previous issues when the raw format was NULL which
resulted in many crashes for sensors which did not have the expected/tested
formats.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add following V4L2 QP parameters for H.264:
* V4L2_CID_MPEG_VIDEO_H264_I_FRAME_MIN_QP
* V4L2_CID_MPEG_VIDEO_H264_I_FRAME_MAX_QP
* V4L2_CID_MPEG_VIDEO_H264_P_FRAME_MIN_QP
* V4L2_CID_MPEG_VIDEO_H264_P_FRAME_MAX_QP
These controls will limit QP range for intra and inter frame,
provide more manual control to improve video encode quality.
Signed-off-by: Fish Lin <linfish@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
commit f1a2e44a3a ("bpf: add queue and stack maps") introduced new BPF
helper functions:
- BPF_FUNC_map_push_elem
- BPF_FUNC_map_pop_elem
- BPF_FUNC_map_peek_elem
but they were made available only for network BPF programs. This patch
makes them available for tracepoint, cgroup and lirc programs.
Signed-off-by: Alban Crequy <alban@kinvolk.io>
Cc: Mauricio Vasquez B <mauricio.vasquez@polito.it>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The exposure control is clustered with the autoexposure control and
flagged as volatile, but the g_volatile_ctrl() doesn't handle
V4L2_CID_EXPOSURE_AUTO. So, the value of the exposure control can't be
read in autoexposure mode.
This enables to get the exposure control in autoexposure mode by making
ov7740_get_volatile_ctrl() deal with V4L2_CID_EXPOSURE_AUTO.
This also sets the exposure control as volatile by specifying the
argument to v4l2_ctrl_auto_cluster() instead of manually flagging it.
Cc: Wenyou Yang <wenyou.yang@microchip.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of doing the cast, just change the type to char.
Suggested-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The strncpy() function is being deprecated upstream. Replace
it by the safer strscpy().
While here, replace a few occurences of strlcpy() that were
recently added to also use strscpy().
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The support for those two formats are archtecture-dependent.
Use the endianness to CPU macros to do it right.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The st_register() returns have changed over time, but these days it
never returns -1. We should just be checking for any negative error
codes.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Smatch marks skb->data as untrusted so it warns that "evt_hdr->dlen"
can copy up to 255 bytes and we only have room for two bytes. Even
if this comes from the firmware and we trust it, the new policy
generally is just to fix it as kernel hardenning.
I can't test this code so I tried to be very conservative. I considered
not allowing "evt_hdr->dlen == 1" because it doesn't initialize the
whole variable but in the end I decided to allow it and manually
initialized "asic_id" and "asic_ver" to zero.
Fixes: e8454ff7b9 ("[media] drivers:media:radio: wl128x: FM Driver Common sources")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
'vb' null check should be done before dereferencing it in
tw5864_handle_frame, otherwise a NULL pointer dereference
may occur.
Fixes: 34d1324edd ("[media] pci: Add tw5864 driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case usb_alloc_coherent fails, the fix returns -ENOMEM to
avoid a potential NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
devm_kcalloc may fail and return a null pointer. The fix returns
-ENOMEM upon failures to avoid null pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This member is never read throughout the code, so remove it.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem
buffer helpers") fixed the return types for mem2mem buffer helper
functions by changing a few local variables from vb2_buffer to
vb2_v4l2_buffer. However, it left a few accesses to vb2_buffer::planes
as-is, accidentally turning them into accesses to
vb2_v4l2_buffer::planes and resulting in values being read from/written
to the wrong place.
Fix this by inserting vb2_buf into these accesses so they mimic their
original behavior.
Fixes: 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem buffer helpers")
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This code generates a static checker warning:
drivers/media/v4l2-core/v4l2-ctrls.c:2921 v4l2_querymenu()
warn: should '(1 << i)' be a 64 bit type?
The problem is that "ctrl->menu_skip_mask" is a u64 and we're only
testing the lower 32 bits.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
clang warns about a possible variable use that gcc never
complained about:
drivers/media/platform/davinci/isif.c:982:32: error: variable 'frame_size' is uninitialized when used here
[-Werror,-Wuninitialized]
dm365_vpss_set_pg_frame_size(frame_size);
^~~~~~~~~~
drivers/media/platform/davinci/isif.c:887:2: note: variable 'frame_size' is declared here
struct vpss_pg_frame_size frame_size;
^
1 error generated.
There is no initialization for this variable at all, and there
has never been one in the mainline kernel, so we really should
not put that stack data into an mmio register.
On the other hand, I suspect that gcc checks the condition
more closely and notices that the global
isif_cfg.bayer.config_params.test_pat_gen flag is initialized
to zero and never written to from any code path, so anything
depending on it can be eliminated.
To shut up the clang warning, just remove the dead code manually,
it has probably never been used because any attempt to do so
would have resulted in undefined behavior.
Fixes: 63e3ab142f ("V4L/DVB: V4L - vpfe capture - source for ISIF driver on DM365")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Building tda1997x fails now unless V4L2_FWNODE is selected:
drivers/media/i2c/tda1997x.o: in function `tda1997x_parse_dt'
undefined reference to `v4l2_fwnode_endpoint_parse'
While at it, also sort the selections alphabetically
Fixes: 9ac0038db9 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: stable@vger.kernel.org # v4.17+
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In order to prevent ISOC URBs from being infinitely resubmitted,
the driver's USB disconnect handler must kill all the in-flight URBs.
While here, change the URB packet status message to a debug level,
to avoid spamming the console too much.
This commit fixes a lockup caused by an interrupt storm coming
from the URB completion handler.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Smatch warns about small size on two structs:
drivers/media/platform/qcom/venus/hfi_parser.c:103 parse_profile_level() error: memcpy() 'proflevel' too small (8 vs 128)
drivers/media/platform/qcom/venus/hfi_parser.c: drivers/media/platform/qcom/venus/hfi_parser.c:129 parse_caps() error: memcpy() 'cap' too small (16 vs 512)
The reason is that the hfi_parser actually expects:
- multiple data entries on hfi_capabilities
- multiple profile_level on hfi_profile_level_supported
However, the structs trick gcc, making it to believe that
there's just one value for each.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The only way for p_set to be NULL would be if vin_coef_set would be an
empty array.
On such case, the driver will OOPS, as it would try to de-reference a
NULL value. So, the check if p_set is not NULL doesn't make any sense.
Solves those two smatch warnings:
drivers/media/platform/rcar-vin/rcar-dma.c:489 rvin_set_coeff() warn: variable dereferenced before check 'p_set' (see line 484)
drivers/media/platform/rcar-vin/rcar-dma.c:494 rvin_set_coeff() error: we previously assumed 'p_set' could be null (see line 489)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
At the error logic, ipc_buf was already asigned to &ctx->ipc_buf_struct,
with can't be null, as warned by smatch:
drivers/media/platform/sti/delta/delta-ipc.c:223 delta_ipc_open() warn: variable dereferenced before check 'ctx->ipc_buf' (see line 183)
So, remove the uneeded check.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The way the code works, compression will be a valid value (less or equal to 3)
on both set_video_mode_foo() calls at the beginning of the while() loop.
So, the value for pChoose can't be NULL.
Solves those smatch warnings:
drivers/media/usb/pwc/pwc-ctrl.c: drivers/media/usb/pwc/pwc-ctrl.c:252 set_video_mode_Timon() warn: variable dereferenced before check 'pChoose' (see line 248)
drivers/media/usb/pwc/pwc-ctrl.c: drivers/media/usb/pwc/pwc-ctrl.c:302 set_video_mode_Kiara() warn: variable dereferenced before check 'pChoose' (see line 298)
and simplifies the code a little bit.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are some macros at cx2341x_update() with seemed to
be introduced in order to ensure that lines would be less
than 80 columns.
Well, the thing is that they make the code harder to be analized,
not only by humans, but also for static code analyzers:
drivers/media/common/cx2341x.c:1116 cx2341x_update() error: we previously assumed 'old' could be null (see line 1047)
So, remove the "force" var, and replace the NEQ macro to a
better designed one that makes clearer about what it is doing.
While here, also remove the "temporal" var, as it is just another
way of doing the same type of check as the new CMP_FIELD() macro
already does.
Finally, fix coding style at the block code.
remove such macros.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As warned by smatch:
drivers/media/i2c/imx214.c:591 imx214_set_format() warn: variable dereferenced before check 'format' (see line 589)
It turns that the code at imx214_set_format() has support for being
called with the format being NULL. I've no idea why, as it is only
called internally with the pointer set, and via subdev API (with
should also set it).
Also, the entire logic there depends on having format != NULL, so
just remove the bogus broken support for a null format.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Indentation is odd in several places, especially when printing messages
to the kernel log. Fix it to match the usual coding style.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
for stateless decoder, set the output pixelformat
to V4L2_PIX_FMT_FWHT_STATELESS and the pix info to
pixfmt_stateless_fwht
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Implement a stateless decoder for the new node.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: add 'return 0;' before default case in vicodec_try_ctrl()]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add stateless decoder instance field to the dev struct and
register another node for the statelsess decoder.
The stateless API for the node will be implemented in further patches.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix typo: videdev-stateless-dec -> stateless-decoder]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add V4L2_PIX_FMT_FWHT_STATELESS to the list of pixelformats that
v4l_fill_fmtdesc() understands.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add structs and definitions needed to implement stateless
decoder for fwht and add I/P-frames QP controls to the
public api.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add struct 'vicodec_dev_instance' for the fields in vicodec_dev
that have have both decoder and encoder versions.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the stateless decoder the reference buffer is null if the
frame is an I-frame (flagged with FWHT_FL_I_FRAME).
Make sure not to dereference it in that case.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename 'v4l2_fwht_default_fmt' to 'v4l2_fwht_find_nth_fmt'
and add a function 'v4l2_fwht_validate_fmt' to check if
a format info matches the parameters.
This function will also be used to validate the stateless
params when adding support for stateless codecs.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move the code that validates version dependent header
values to a separate function 'validate_by_version'
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the decoder, save the inner reference frame in the same
format as the capture buffer.
The decoder writes directly to the capture buffer and then
the capture buffer is copied to the reference buffer.
This will simplify the stateless decoder.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the field 'buf' to fwht_raw_frame to indicate
the start of the raw frame buffer.
This field will be used to copy the capture buffer
to the reference buffer in the next patch.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Introduce 'prepare_raw_frame' function that fills the values
of a raw frame struct according to the format.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function 'v4l2_m2m_buf_copy_metadata' should
be called even if decoding/encoding ends with
status VB2_BUF_STATE_ERROR, so that the metadata
is copied from the source buffer to the dest buffer.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_fwht_encode returns either an error code on
failure or the size of the compressed frame on
success. So change the var assigned to it from
'ret' to 'comp_sz_or_errcode' to clarify that.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If one of the controls fails to set,
then 'v4l2_ctrl_request_setup'
immediately returns with the error code.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
'v4l2_m2m_ctx_release' calls request complete
so it should be called before 'v4l2_ctrl_handler_free'.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The logic of g_selection was wrong: encoders support crop,
decoders support compose, but the code allowed both.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The selection api should check only single buffer types
because multiplanar types are converted to
single in drivers/media/v4l2-core/v4l2-ioctl.c
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Laurent Pinchart