Media bus codes were being mapped to pixelformats, which causes a
limitation on vimc because not all pixelformats can be mapped to media
bus codes.
Also, media bus codes are an internal configuration from the device.
Userspace only assures media bus codes matches between pads and expects
the image in a given pixelformat. So we can allow almost any media bus
format to be configured between pads, except for debayer that expects a
media bus code of type bayer in the sink pad.
[hverkuil-cisco@xs4all.nl: drop use of v4l2_get_fourcc_name: not yet available]
[hverkuil-cisco@xs4all.nl: made vimc_mbus_list static]
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is mandatory to write CEC_CFGR only when CECEN=0. To protect
transmission, a check have been added to delayed logical address
modification. This patch is necessary tp pass all tests of compliance.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ISC will output the "ARGB32" configuration in byte order: B, G, R, Alpha.
This is in fact the format BGRA, aka ABGR32.
If alpha is missing, the same format is equivalent to XBGR32.
Added both formats and removed ARGB32 which is wrong.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This change is a redesign in the formats and the way the ISC is
configured w.r.t. sensor format and the output format from the ISC.
I have changed the splitting between sensor output (which is also ISC input)
and ISC output.
The sensor format represents the way the sensor is configured, and what ISC
is receiving.
The format configuration represents the way ISC is interpreting the data and
formatting the output to the subsystem.
Now it's much easier to figure out what is the ISC configuration for input, and
what is the configuration for output.
The non-raw format can be obtained directly from sensor or it can be done
inside the ISC. The controller format list will include a configuration for
each format.
The old supported formats are still in place, if we want to dump the sensor
format directly to the output, the try format routine will detect and
configure the pipeline accordingly.
This also fixes the previous issues when the raw format was NULL which
resulted in many crashes for sensors which did not have the expected/tested
formats.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The strncpy() function is being deprecated upstream. Replace
it by the safer strscpy().
While here, replace a few occurences of strlcpy() that were
recently added to also use strscpy().
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The support for those two formats are archtecture-dependent.
Use the endianness to CPU macros to do it right.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
devm_kcalloc may fail and return a null pointer. The fix returns
-ENOMEM upon failures to avoid null pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This member is never read throughout the code, so remove it.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem
buffer helpers") fixed the return types for mem2mem buffer helper
functions by changing a few local variables from vb2_buffer to
vb2_v4l2_buffer. However, it left a few accesses to vb2_buffer::planes
as-is, accidentally turning them into accesses to
vb2_v4l2_buffer::planes and resulting in values being read from/written
to the wrong place.
Fix this by inserting vb2_buf into these accesses so they mimic their
original behavior.
Fixes: 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem buffer helpers")
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
clang warns about a possible variable use that gcc never
complained about:
drivers/media/platform/davinci/isif.c:982:32: error: variable 'frame_size' is uninitialized when used here
[-Werror,-Wuninitialized]
dm365_vpss_set_pg_frame_size(frame_size);
^~~~~~~~~~
drivers/media/platform/davinci/isif.c:887:2: note: variable 'frame_size' is declared here
struct vpss_pg_frame_size frame_size;
^
1 error generated.
There is no initialization for this variable at all, and there
has never been one in the mainline kernel, so we really should
not put that stack data into an mmio register.
On the other hand, I suspect that gcc checks the condition
more closely and notices that the global
isif_cfg.bayer.config_params.test_pat_gen flag is initialized
to zero and never written to from any code path, so anything
depending on it can be eliminated.
To shut up the clang warning, just remove the dead code manually,
it has probably never been used because any attempt to do so
would have resulted in undefined behavior.
Fixes: 63e3ab142f ("V4L/DVB: V4L - vpfe capture - source for ISIF driver on DM365")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Smatch warns about small size on two structs:
drivers/media/platform/qcom/venus/hfi_parser.c:103 parse_profile_level() error: memcpy() 'proflevel' too small (8 vs 128)
drivers/media/platform/qcom/venus/hfi_parser.c: drivers/media/platform/qcom/venus/hfi_parser.c:129 parse_caps() error: memcpy() 'cap' too small (16 vs 512)
The reason is that the hfi_parser actually expects:
- multiple data entries on hfi_capabilities
- multiple profile_level on hfi_profile_level_supported
However, the structs trick gcc, making it to believe that
there's just one value for each.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The only way for p_set to be NULL would be if vin_coef_set would be an
empty array.
On such case, the driver will OOPS, as it would try to de-reference a
NULL value. So, the check if p_set is not NULL doesn't make any sense.
Solves those two smatch warnings:
drivers/media/platform/rcar-vin/rcar-dma.c:489 rvin_set_coeff() warn: variable dereferenced before check 'p_set' (see line 484)
drivers/media/platform/rcar-vin/rcar-dma.c:494 rvin_set_coeff() error: we previously assumed 'p_set' could be null (see line 489)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
At the error logic, ipc_buf was already asigned to &ctx->ipc_buf_struct,
with can't be null, as warned by smatch:
drivers/media/platform/sti/delta/delta-ipc.c:223 delta_ipc_open() warn: variable dereferenced before check 'ctx->ipc_buf' (see line 183)
So, remove the uneeded check.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Indentation is odd in several places, especially when printing messages
to the kernel log. Fix it to match the usual coding style.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
for stateless decoder, set the output pixelformat
to V4L2_PIX_FMT_FWHT_STATELESS and the pix info to
pixfmt_stateless_fwht
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Implement a stateless decoder for the new node.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: add 'return 0;' before default case in vicodec_try_ctrl()]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add stateless decoder instance field to the dev struct and
register another node for the statelsess decoder.
The stateless API for the node will be implemented in further patches.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix typo: videdev-stateless-dec -> stateless-decoder]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add structs and definitions needed to implement stateless
decoder for fwht and add I/P-frames QP controls to the
public api.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add struct 'vicodec_dev_instance' for the fields in vicodec_dev
that have have both decoder and encoder versions.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the stateless decoder the reference buffer is null if the
frame is an I-frame (flagged with FWHT_FL_I_FRAME).
Make sure not to dereference it in that case.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename 'v4l2_fwht_default_fmt' to 'v4l2_fwht_find_nth_fmt'
and add a function 'v4l2_fwht_validate_fmt' to check if
a format info matches the parameters.
This function will also be used to validate the stateless
params when adding support for stateless codecs.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move the code that validates version dependent header
values to a separate function 'validate_by_version'
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the decoder, save the inner reference frame in the same
format as the capture buffer.
The decoder writes directly to the capture buffer and then
the capture buffer is copied to the reference buffer.
This will simplify the stateless decoder.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the field 'buf' to fwht_raw_frame to indicate
the start of the raw frame buffer.
This field will be used to copy the capture buffer
to the reference buffer in the next patch.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Introduce 'prepare_raw_frame' function that fills the values
of a raw frame struct according to the format.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function 'v4l2_m2m_buf_copy_metadata' should
be called even if decoding/encoding ends with
status VB2_BUF_STATE_ERROR, so that the metadata
is copied from the source buffer to the dest buffer.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_fwht_encode returns either an error code on
failure or the size of the compressed frame on
success. So change the var assigned to it from
'ret' to 'comp_sz_or_errcode' to clarify that.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
'v4l2_m2m_ctx_release' calls request complete
so it should be called before 'v4l2_ctrl_handler_free'.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The logic of g_selection was wrong: encoders support crop,
decoders support compose, but the code allowed both.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The selection api should check only single buffer types
because multiplanar types are converted to
single in drivers/media/v4l2-core/v4l2-ioctl.c
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Checkpatch wants to use 'help' instead of '---help---':
WARNING: prefer 'help' over '---help---' for new help texts
Let's change it globally at the media subsystem, as otherwise people
would keep using the old way.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ti-vpe driver parsed the remote endpoints for properties but ignored the
local ones. Fix this by parsing the local endpoint properties instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
V4L2 fwnode matching right now still works based on device nodes, not port
nodes. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When start_streaming was called both last_src_buf and last_dst_buf
pointers were set to NULL, but this depends on whether the capture
or output queue starts streaming.
When decoding with resolution changes in between the capture queue
has to restart streaming whenever a resolution change occurs. And
that would reset last_src_buf as well, which causes a problem if
the decoder was stopped by the application. Since last_src_buf
is now NULL, the LAST flag is never set for the last capture
buffer.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some functions like enum_fmt use the buffer type as was passed
from userspace, which might cause the switch to fall into the
default case. Just drop the WARN_ON(1) to avoid kernel log pollution.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The s_stream callback was not being called for the first entity in the
stream pipeline array.
Instead of verifying the type of the node (video or subdevice) and
calling s_stream from the second entity in the pipeline, do this process
for all the entities in the pipeline for consistency.
The previous code was not a problem because the first entity is a video
device and not a subdevice, but this patch prepares vimc to allow
setting some configuration in the entity before calling s_stream.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Tested-by: André Almeida <andre.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix line-too-long warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is no need to have the frame field in the vimc_stream struct.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Tested-by: André Almeida <andre.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The type V4L2_FRMSIZE_TYPE_CONTINUOUS expects a step of 1.
This fixes v4l2-compliance test error:
fail: v4l2-test-formats.cpp(184): invalid step_width/height for continuous framesize
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The state TASK_UNINTERRUPTIBLE should be set just before
schedule_timeout() call, so it knows the sleep mode it should enter.
There is no point in setting TASK_UNINTERRUPTIBLE at the initialization
of the thread as schedule_timeout() will set the state back to
TASK_RUNNING.
This fixes a warning in __might_sleep() call, as it's expecting the
task to be in TASK_RUNNING state just before changing the state to
a sleeping state.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The format of the sink pad should be a bayer mbus format.
This fixes a kernel NULL pointer dereference error that was caused when
the stream starts because the configured format was not found in the
pixelmap table.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clang-9 makes some different inlining decisions compared to gcc, which
leads to a warning about a possible stack overflow problem when building
with CONFIG_KASAN, including when setting asan-stack=0, which avoids
most other frame overflow warnings:
drivers/media/platform/vicodec/codec-fwht.c:673:12: error: stack frame size of 2224 bytes in function 'encode_plane'
Manually adding noinline_for_stack annotations in those functions
called by encode_plane() or decode_plane() that require a significant
amount of kernel stack makes this impossible to happen with any
compiler.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ISC driver currently supports ITU-R 601 encoding which
utilizes the external hsync and vsync signals. ITU-R 656
format removes the need for these pins by embedding the
sync pulses within the data packet.
To support this feature, enable necessary register bits
when this feature is enabled via device tree.
Signed-off-by: Ken Sloat <ksloat@aampglobal.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Avoid call of dmaengine_terminate_all() between
dmaengine_prep_slave_single() and dmaengine_submit() by locking
the whole DMA submission sequence.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Start streaming was sometimes failing because of pm_runtime_get_sync()
non-0 return value. In fact return value was not an error but a
positive value (1), indicating that PM was already enabled.
Fix this by going to error path only with negative return value.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Function `sh_veu_find_fmt` returns an address that is an addition of a
base pointer `sh_veu_fmt` and an offset. The base pointer refers to a
global variable of which address cannot be NULL. Therefore, this commit
removes the NULL pointer checks on the return values of function
`sh_veu_find_fmt`.
Signed-off-by: Shaobo He <shaobo@cs.utah.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem
buffer helpers") fixed the return types for mem2mem buffer helper
functions, but omitted two occurrences that are accessed in the
mtk_v4l2_debug() macro. These only trigger compiler errors when DEBUG is
defined.
Fixes: 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem buffer helpers")
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the SoC specific information for RZ/G2M(r8a774a1) SoC.
The VIN module of RZ/G2M is similar to R-Car M3-W.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the MIPI CSI-2 driver support for RZ/G2M(r8a774a1) SoC.
The CSI-2 module of RZ/G2M is similar to R-Car M3-W.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
devm_ioremap_resource() already prints an error message on failure, so
there is no need to repeat that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Changes to v4l2-fwnode in commit [1] triggered a lockdep warning in
rcar-vin. The first attempt to solve this warning in the rcar-vin driver
was incomplete and only pushed the warning to happen at stream on time
instead of at probe time.
This change reverts the incomplete fix and properly fixes the warning by
removing the need to hold the rcar-vin specific group lock when calling
v4l2_async_notifier_parse_fwnode_endpoints_by_port(). And instead takes
it in the callback where it's really needed.
[1] commit eae2aed1ea ("media: v4l2-fwnode: Switch to
v4l2_async_notifier_add_subdev")
Fixes: 6458afc8c4 ("media: rcar-vin: remove unneeded locking in async callbacks")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the new v4l2_subdev_internal_ops release op to free the
subdev memory only when the last user closed the file handle.
Move v4l2_device_unregister_subdev() to the end of the
vimc_ent_sd_unregister() function since now the unregister_subdev()
call may free the vimc_ent_device struct which is used after the
unregister_subdev() call. So this now has to be done last.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Don't free vimc_cap_device immediately, instead do this
in the video_device release function which is called when the
last user closes the video device. Only then is it safe to
free the memory.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The media_device is part of a static global vimc_device struct.
The media framework expects this to be zeroed before it is
used, however, since this is a global this is not the case if
vimc is unbound and then bound again.
So call memset to ensure any left-over values are cleared.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is not possible to use devm_kzalloc since that memory is
freed immediately when the device instance is unbound.
Various objects like the video device may still be in use
since someone has the device node open, and when that is closed
it expects the memory to be around.
So use kzalloc and release it at the appropriate time.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When vivid is unloaded it used vfree to free dev->bitmap_out,
but it was actually allocated using kmalloc. Use vzalloc
instead, conform what vivid-vid-cap.c does.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Extend the vsp1_du_atomic_flush() API with writeback support by adding
format, pitch and memory addresses of the writeback framebuffer.
Writeback completion is reported through the existing frame completion
callback with a new VSP1_DU_STATUS_WRITEBACK status flag.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The VSP1 driver will need to pass extra flags to the DU through the
frame completion API. Replace the completed bool flag by a bitmask to
support this.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The code that initializes the RPF format-related fields for display
pipelines will also be useful for the WPF to implement writeback
support. Split it from vsp1_du_atomic_update() to a new
vsp1_du_pipeline_set_rwpf_format() function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the writeback feature of the WPF, to enable capturing
frames at the WPF output for display pipelines. To enable writeback the
vsp1_rwpf structure mem field must be set to the address of the
writeback buffer and the writeback field set to true before the WPF
.configure_stream() and .configure_partition() are called. The WPF will
enable writeback in the display list for a single frame, and writeback
will then be automatically disabled.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Refactor the display list header setup to allow chained display lists
with display pipelines. Chain the display lists as for mem-to-mem
pipelines, but enable the frame end interrupt for every list as display
pipelines have a single list per frame.
This feature will be used to disable writeback exactly one frame after
enabling it by chaining a writeback disable display list.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The WPF needs access to the current display list to configure writeback.
Add a display list pointer to the VSP1 entity .configure_stream()
operation.
Only display pipelines can make use of the display list there as
mem-to-mem pipelines don't have access to a display list at stream
configuration time. This is not an issue as writeback is only used for
display pipelines.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To prepare for addition of more flags to the display list, replace the
'internal' flag field by a bitmask 'flags' field.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The VSP-DL instances have two LIFs, and thus two copies of the
VI6_DISP_IRQ_ENB, VI6_DISP_IRQ_STA and VI6_WPF_WRBCK_CTRL registers. Fix
the corresponding macros accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Display list fragments have been renamed to bodies. Replace one last
occurrence of the word fragment in the documentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When configuring partitions for memory-to-memory pipelines, the WPF
accesses data of the current partition through pipe->partition.
Writeback support will require full configuration of the WPF while not
providing a valid pipe->partition. Rework the configuration code to fall
back to the full image width in that case, as is already done for the
part of the configuration currently relevant for display pipelines.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This reverts commit 3299ba5c0b ("[media] v4l: vsp1: Supply frames to
the DU continuously")
The DU output mode does not rely on frames being supplied on the WPF as
its pipeline is supplied from DRM. For the upcoming WPF writeback
functionality, we will choose to enable writeback mode if there is an
output buffer, or disable it (leaving the existing display pipeline
unharmed) otherwise.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
- Fix a unittest failure on UML. Preparation for converting to
kunit test framework.
- Add annotations to dtx_diff output
- Fix unittest reporting of expected error
- Move DMA configuration for virtual devices into the driver that
needs it (s5p-mfc)
- Vendor prefixes for feiyang and techstar
- Convert ARM GIC, GICv3, and L2x0 to DT schema
- Add r8a7778/9 HSCIF serial bindings
-----BEGIN PGP SIGNATURE-----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=CnTd
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- Fix a unittest failure on UML. Preparation for converting to kunit
test framework.
- Add annotations to dtx_diff output
- Fix unittest reporting of expected error
- Move DMA configuration for virtual devices into the driver that needs
it (s5p-mfc)
- Vendor prefixes for feiyang and techstar
- Convert ARM GIC, GICv3, and L2x0 to DT schema
- Add r8a7778/9 HSCIF serial bindings
* tag 'devicetree-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: unittest: unflatten device tree on UML when testing
dt-bindings: Add vendor prefix for feiyang
dt-bindings: Add vendor prefix for techstar
dt-bindings: display: add missing semicolon in example
of: mark early_init_dt_alloc_reserved_memory_arch static
of: add dtc annotations functionality to dtx_diff
of: unittest: add caution to function header comment
of: unittest: remove report of expected error
dt-bindings: interrupt-controller: Convert ARM GICv3 to json-schema
dt-bindings: interrupt-controller: Convert ARM GIC to json-schema
dt-bindings: arm: l2x0: Convert L2 cache to json-schema
media: s5p-mfc: Fix memdev DMA configuration
dt-bindings: serial: sh-sci: Document r8a7778/9 HSCIF bindings
As we did lots of change at vim2m driver, let's take the
opportunity and make checkpatch happier, addressing the
errors/warnings that makes sense.
While here, increment driver's version.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There's no reason why this driver should use BUG(). Instead,
just properly handle issue, returning an error code where
pertinent.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When in passthrough mode, copy the entire line at once, in
order to make it faster (if not HFLIP).
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add an horizontal linear scaler using Breseham algorithm in
order to speep up its calculus.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Handling any Y,Cr,Cb formats require some extra logic, as it
handles a group of two pixels. That's easy while we don't do
horizontal scaling.
However, doing horizontal scaling with such formats would require
a lot more code, in order to avoid distortions, as, if it scales
to two non-consecutive points, the logic would need to read 4
points in order to properly convert to RGB.
As this is just a test driver, and we want fast algorithms,
let's just get rid of this format as an output one.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When resolutions are different, the expected behavior is to
scale the image. Implement a vertical scaler as the first step.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vim2m driver doesn't enforce that the capture and output
buffers would have the same size. Do the right thing if the
buffers are different, zeroing the buffer before writing,
ensuring that lines will be aligned and it won't write past
the buffer area.
This is a temporary fix.
A proper fix is to either implement a simple scaler at vim2m,
or to better define the behaviour of M2M transform drivers
at V4L2 API with regards to its capability of scaling the
image or not.
In any case, such changes would deserve a separate patch
anyway, as it would imply on some behavoral change.
Also, as we have an actual bug of writing data at wrong
places, let's fix this here, and add a mental note that
we need to properly address it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The only real restriction at vim2m is that width should be
multiple of two, as the copy routine always copy two pixels
each time.
However, Bayer formats are defined as having a 2x2 matrix.
So, odd vertical numbers would cause color distortions at the
last line. So, it makes sense to use step 2 for vertical alignment
on Bayer.
With this patch, the reported formats for video capture will
be:
[0]: 'RGBP' (16-bit RGB 5-6-5)
Size: Stepwise 32x32 - 640x480 with step 2/1
[1]: 'RGBR' (16-bit RGB 5-6-5 BE)
Size: Stepwise 32x32 - 640x480 with step 2/1
[2]: 'RGB3' (24-bit RGB 8-8-8)
Size: Stepwise 32x32 - 640x480 with step 2/1
[3]: 'BGR3' (24-bit BGR 8-8-8)
Size: Stepwise 32x32 - 640x480 with step 2/1
[4]: 'YUYV' (YUYV 4:2:2)
Size: Stepwise 32x32 - 640x480 with step 2/1
[5]: 'BA81' (8-bit Bayer BGBG/GRGR)
Size: Stepwise 32x32 - 640x480 with step 2/2
[6]: 'GBRG' (8-bit Bayer GBGB/RGRG)
Size: Stepwise 32x32 - 640x480 with step 2/2
[7]: 'GRBG' (8-bit Bayer GRGR/BGBG)
Size: Stepwise 32x32 - 640x480 with step 2/2
[8]: 'RGGB' (8-bit Bayer RGRG/GBGB)
Size: Stepwise 32x32 - 640x480 with step 2/2
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The copy logic assumes that the data width is multiple of two,
as this is needed in order to support YUYV.
There's no reason to force it to be 8-pixel aligned, as 2-pixel
alignment is enough.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vim2m device is interesting to simulate a webcam. As most
sensors are arranged using bayer formats, the best is to support
to output data using those formats.
So, add support for them.
All 4 8-bit bayer formats tested with:
$ qvidcap -p &
$ v4l2-ctl --stream-mmap --stream-out-mmap --stream-to-host localhost --stream-lossless --stream-out-hor-speed 1 -v pixelformat=RGGB
It was tested also with GStreamer with:
$ gst-validate-1.0 filesrc location=some_video.mp4 ! qtdemux ! avdec_h264 ! videoconvert ! videoscale ! v4l2convert disable-passthrough=1 extra-controls="s,horizontal_flip=0,vertical_flip=0" ! bayer2rgb ! videoconvert ! xvimagesink
For all possible HFLIP/VFLIP values.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Those typos were left over from codespell check, on
my first pass or belong to code added after the time I
ran it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add non vendor bayer formats to the allowed format array.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a flag 'FWHT_FL_I_FRAME' that indicates that
this is an I-frame. This requires incrementing
to version 3
This flag is needed for the upcoming stateless FWHT
decoder since it has to know if an encoded frame is
an I or a P frame.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
[hverkuil-cisco@xs4all.nl: added the last paragraph of the commit msg]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The check to see if type is V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE is redundant
as this has been already checked at the start of the function and if
it's not that value then -ENOSYS is returned. Hence the sprintf can be
replaced by a simpler string copy.
Detected by CoverityScan, CID#1309450 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CSI controller can take raw data from the data bus and output it
directly to capture buffers. This can be used to support the JPEG media
bus format.
While the controller can report minimum and maximum bytes per line, it
has no way to report how many lines were captured in the last frame.
Thus, even when the on-bus data is framed correctly, we have no way to
accertain the actual amount of data captured, unless we scan the buffer
for JPEG EOI markers, or sequential zeros. For now we leave bytesused
alone, and leave it up to userspace applications to parse the data.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CSI controller can take raw data from the data bus and output RGB565
format. The controller does not distinguish between RGB565 LE and BE.
Instead this is determined by the media bus format, i.e. the format or
order the sensor is sending data in.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
max_register is currently set to 0x1000. This is beyond the mapped
address range of the hardware, so attempts to dump the regmap from
debugfs would trigger a kernel exception.
Furthermore, the useful registers only occupy a small section at the
beginning of the full range. Change the value to 0x9c, the last known
register on the V3s and H3.
On the A31, the register range is extended to support additional
capture channels. Since this is not yet supported, ignore it for now.
Fixes: 5cc7522d89 ("media: sun6i: Add support for Allwinner CSI V3s")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/media/platform/vsp1/vsp1_drm.c: drivers/media/platform/vsp1/vsp1_drm.c:336 vsp1_du_pipeline_setup_brx() error: we previously assumed 'pipe->brx' could be null (see line 244)
smatch missed that if pipe->brx was NULL, then later on it will be
set with a non-NULL value. But it is easier to just use the brx pointer
so smatch doesn't get confused.
Tested-on: Salvator-XS-ES2.0, Salvator-XS-M3N
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CSI block in Allwinner A64 has similar features as like in H3,
but the default CSI_SCLK rate cannot work properly to drive the
connected sensor interface.
The tested mod cock rate is 300 MHz and BSP vfe media driver is also
using the same rate. Unfortunately there is no valid information about
clock rate in manual or any other sources except the BSP driver. so more
faith on BSP code, because same has tested in mainline.
So, add support for A64 CSI block by setting updated mod clock rate.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Buffers generated with YUV32 format seems to be incorrect, hence use
VUYA32 instead.
Changes from v1:
Add both formats VUYA32 and VUYX32 but associate only VUYX32 to the
output queue as the alpha channel of buffers is ignored on this queue.
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Helen Fornazier