Some usb PHYs need power supply from vbus to make it work, eg mxs-phy, if
there is no vbus, USB PHY will not in correct state when the controller starts
to work, for host, this requires vbus should be turned on before setting port
power(PP) of ehci, to work with this kind of USB PHY design, this patch adds
a flag CI_HDRC_TURN_VBUS_EARLY_ON, can be checked by host driver to turn on
vbus while start host.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, USB PHY is mandatory for chipidea core, the flag
CI_HDRC_REQUIRE_TRANSCEIVER is useless.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support of the PHY framework for ChipIdea drivers.
Changes are done in both the ChipIdea common code and in the drivers
accessing the PHY. This is done by adding a new PHY member in
ChipIdea's structures and by taking care of it in the code.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch modify the generic code handling PHYs to allow them to be
supplied from the drivers. This adds checks to ensure no PHY was already
there when looking for one in the generic code. This also makes sure we
do not modify its state in the generic HCD functions, it was provided by
the driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For OTG and Embedded hosts, they may need TPL (Targeted Peripheral List)
for usb certification and other vender specific requirements, the
platform can tell chipidea core driver if it supports tpl through DT
or platform data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes it possible to set the chipidea udc into full-speed only mode.
It is set by the oftree property "maximum-speed = full-speed".
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement special hw_write
and hw_test_and_clear for imx28.
Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2
This patch is needed for stable tree 3.11+.
Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the controller only runs when the ci->vbus_active is true.
So the flag CI_HDRC_PULLUP_ON_VBUS is useless no longer.
If the user doesn't have otgsc, he/she needs to change ci_handle_vbus_change
to update ci->vbus_active.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we need otgsc to know vbus's status at some chipidea
controllers even it is peripheral-only mode. Besides, some
SoCs (eg, AR9331 SoC) don't have otgsc register even
the DCCPARAMS_DC and DCCPARAMS_HC are both 1 at CAP_DCCPARAMS.
We inroduce flag CI_HDRC_DUAL_ROLE_NOT_OTG to indicate if the
controller is dual role, but not supports OTG. If this flag is
not set, we follow the rule that if DCCPARAMS_DC and DCCPARAMS_HC
are both 1 at CAP_DCCPARAMS, then this controller is otg capable.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vbus regulator is a common element for USB vbus operation,
So, move it from glue layer to core.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"ci13xxx" is bad for at least the following reasons:
* people often mistype it
* it doesn't add any informational value to the names it's used in
* it needlessly attracts mail filters
This patch replaces it with "ci_hdrc", "ci_udc" or "ci_hw", depending
on the situation. Modules with ci13xxx prefix are also renamed accordingly
and aliases are added for compatibility. Otherwise, no functional changes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if a chipidea core is otg capable the board may not be. This allows
to explicitly set the core to host/peripheral mode. Without these flags
the driver falls back to the old behaviour.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes it possible to configure the PTW, PTS and STS bits
inside the portsc register for host and device mode before the driver
starts and the phy can be addressed as hardware implementation is
designed.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes, the driver bindings may know what phy they use.
For example, when using device tree, the usb controller may have a
phandler pointing to usb phy.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Subodh Nijsure <snijsure@grid-net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers do the similar things to add/remove ci13xxx device, so
create a unified one.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct ci13xxx represent the controller, which may be device or host,
so name its variables as ci.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch rename struct ci13xxx_udc_driver and var with the type.
ci13xxx_platform_data reflect it's passed from platfrom driver.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some implementations need this limitation to work correctly.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Li Jun