man ip-tunnel ttl section says:
0 is a special value meaning that packets inherit the TTL value.
IPv4 tunnel respect this in ip_tunnel_xmit(), but IPv6 tunnel has not
implement it yet. To make IPv6 behave consistently with IP tunnel,
add ipv6 tunnel inherit support.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jan reported a regression after an update to 4.18.5. In this case ipv6
default route is setup by systemd-networkd based on data from an RA. The
RA contains an MTU of 1492 which is used when the route is first inserted
but then systemd-networkd pushes down updates to the default route
without the mtu set.
Prior to the change to fib6_info, metrics such as MTU were held in the
dst_entry and rt6i_pmtu in rt6_info contained an update to the mtu if
any. ip6_mtu would look at rt6i_pmtu first and use it if set. If not,
the value from the metrics is used if it is set and finally falling
back to the idev value.
After the fib6_info change metrics are contained in the fib6_info struct
and there is no equivalent to rt6i_pmtu. To maintain consistency with
the old behavior the new code should only reset the MTU in the metrics
if the route update has it set.
Fixes: d4ead6b34b ("net/ipv6: move metrics from dst to rt6_info")
Reported-by: Jan Janssen <medhefgo@web.de>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 80f1a0f4e0 ("net/ipv6: Put lwtstate when destroying fib6_info")
partially fixed the kmemleak [1], lwtstate can be copied from fib6_info,
with ip6_rt_copy_init(), and it should be done only once there.
rt->dst.lwtstate is set by ip6_rt_init_dst(), at the start of the function
ip6_rt_copy_init(), so there is no need to get it again at the end.
With this patch, lwtstate also isn't copied from RTF_REJECT routes.
[1]:
unreferenced object 0xffff880b6aaa14e0 (size 64):
comm "ip", pid 10577, jiffies 4295149341 (age 1273.903s)
hex dump (first 32 bytes):
01 00 04 00 04 00 00 00 10 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<0000000018664623>] lwtunnel_build_state+0x1bc/0x420
[<00000000b73aa29a>] ip6_route_info_create+0x9f7/0x1fd0
[<00000000ee2c5d1f>] ip6_route_add+0x14/0x70
[<000000008537b55c>] inet6_rtm_newroute+0xd9/0xe0
[<000000002acc50f5>] rtnetlink_rcv_msg+0x66f/0x8e0
[<000000008d9cd381>] netlink_rcv_skb+0x268/0x3b0
[<000000004c893c76>] netlink_unicast+0x417/0x5a0
[<00000000f2ab1afb>] netlink_sendmsg+0x70b/0xc30
[<00000000890ff0aa>] sock_sendmsg+0xb1/0xf0
[<00000000a2e7b66f>] ___sys_sendmsg+0x659/0x950
[<000000001e7426c8>] __sys_sendmsg+0xde/0x170
[<00000000fe411443>] do_syscall_64+0x9f/0x4a0
[<000000001be7b28b>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[<000000006d21f353>] 0xffffffffffffffff
Fixes: 6edb3c96a5 ("net/ipv6: Defer initialization of dst to data path")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6d0bfe2261 ("net: ipv6: Add IPv6 support to the ping socket.")
contains an error in the cleanup path of inet6_init(): when
proto_register(&pingv6_prot, 1) fails, we try to unregister
&pingv6_prot. When rawv6_init() fails, we skip unregistering
&pingv6_prot.
Example of panic (triggered by faking a failure of
proto_register(&pingv6_prot, 1)):
general protection fault: 0000 [#1] PREEMPT SMP KASAN PTI
[...]
RIP: 0010:__list_del_entry_valid+0x79/0x160
[...]
Call Trace:
proto_unregister+0xbb/0x550
? trace_preempt_on+0x6f0/0x6f0
? sock_no_shutdown+0x10/0x10
inet6_init+0x153/0x1b8
Fixes: 6d0bfe2261 ("net: ipv6: Add IPv6 support to the ping socket.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 15e668070a ("ipv6: reorder icmpv6_init() and ip6_mr_init()")
moved the cleanup label for ipmr_fail, but should have changed the
contents of the cleanup labels as well. Now we can end up cleaning up
icmpv6 even though it hasn't been initialized (jump to icmp_fail or
ipmr_fail).
Simply undo things in the reverse order of their initialization.
Example of panic (triggered by faking a failure of icmpv6_init):
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN PTI
[...]
RIP: 0010:__list_del_entry_valid+0x79/0x160
[...]
Call Trace:
? lock_release+0x8a0/0x8a0
unregister_pernet_operations+0xd4/0x560
? ops_free_list+0x480/0x480
? down_write+0x91/0x130
? unregister_pernet_subsys+0x15/0x30
? down_read+0x1b0/0x1b0
? up_read+0x110/0x110
? kmem_cache_create_usercopy+0x1b4/0x240
unregister_pernet_subsys+0x1d/0x30
icmpv6_cleanup+0x1d/0x30
inet6_init+0x1b5/0x23f
Fixes: 15e668070a ("ipv6: reorder icmpv6_init() and ip6_mr_init()")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the commit d6990976af ("vti6: fix PMTU caching and reporting
on xmit") '!skb->ignore_df' check was always true because the function
skb_scrub_packet() was called before it, resetting ignore_df to zero.
In the commit, skb_scrub_packet() was moved below, and now this check
can be false for the packet, e.g. when sending it in the two fragments,
this prevents successful PMTU updates in such case. The next attempts
to send the packet lead to the same tx error. Moreover, vti6 initial
MTU value relies on PMTU adjustments.
This issue can be reproduced with the following LTP test script:
udp_ipsec_vti.sh -6 -p ah -m tunnel -s 2000
Fixes: ccd740cbc6 ("vti6: Add pmtu handling to vti6_xmit.")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After erspan_ver is introudced, if erspan_ver is not set in iproute, its
value will be left 0 by default. Since Commit 02f99df187 ("erspan: fix
invalid erspan version."), it has broken the traffic due to the version
check in erspan_xmit if users are not aware of 'erspan_ver' param, like
using an old version of iproute.
To fix this compatibility problem, it sets erspan_ver to 1 by default
when adding an erspan dev in erspan_setup. Note that we can't do it in
ipgre_netlink_parms, as this function is also used by ipgre_changelink.
Fixes: 02f99df187 ("erspan: fix invalid erspan version.")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6edb3c96a5 ("net/ipv6: Defer initialization of dst to data path")
forgot to handle anycast route and init anycast rt->dst.input to ip6_forward.
Fix it by setting anycast rt->dst.input back to ip6_input.
Fixes: 6edb3c96a5 ("net/ipv6: Defer initialization of dst to data path")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the 3 callers of addrconf_add_mroute() assert RTNL
lock, they don't take any additional lock either, so
it is safe to convert it to GFP_KERNEL.
Same for sit_add_v4_addrs().
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to the introduction of fib6_info lwtstate was managed by the dst
code. With fib6_info releasing lwtstate needs to be done when the struct
is freed.
Fixes: 93531c6743 ("net/ipv6: separate handling of FIB entries from dst based routes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When set fb_tunnels_only_for_init_net to 1, don't create fallback tunnel
device for vti6 when a new namespace is created.
Tested:
[root@builder2 ~]# modprobe ip6_tunnel
[root@builder2 ~]# modprobe ip6_vti
[root@builder2 ~]# echo 1 > /proc/sys/net/core/fb_tunnels_only_for_init_net
[root@builder2 ~]# unshare -n
[root@builder2 ~]# ip link
1: lo: <LOOPBACK> mtu 65536 qdisc noop state DOWN mode DEFAULT group
default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same as ip_vti, use iptunnel_xmit_stats to updates stats in tunnel xmit
code path.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roman reports that DHCPv6 client no longer sees replies from server
due to
ip6tables -t raw -A PREROUTING -m rpfilter --invert -j DROP
rule. We need to set the F_IFACE flag for linklocal addresses, they
are scoped per-device.
Fixes: 47b7e7f828 ("netfilter: don't set F_IFACE on ipv6 fib lookups")
Reported-by: Roman Mamedov <rm@romanrm.net>
Tested-by: Roman Mamedov <rm@romanrm.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-08-13
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add driver XDP support for veth. This can be used in conjunction with
redirect of another XDP program e.g. sitting on NIC so the xdp_frame
can be forwarded to the peer veth directly without modification,
from Toshiaki.
2) Add a new BPF map type REUSEPORT_SOCKARRAY and prog type SK_REUSEPORT
in order to provide more control and visibility on where a SO_REUSEPORT
sk should be located, and the latter enables to directly select a sk
from the bpf map. This also enables map-in-map for application migration
use cases, from Martin.
3) Add a new BPF helper bpf_skb_ancestor_cgroup_id() that returns the id
of cgroup v2 that is the ancestor of the cgroup associated with the
skb at the ancestor_level, from Andrey.
4) Implement BPF fs map pretty-print support based on BTF data for regular
hash table and LRU map, from Yonghong.
5) Decouple the ability to attach BTF for a map from the key and value
pretty-printer in BPF fs, and enable further support of BTF for maps for
percpu and LPM trie, from Daniel.
6) Implement a better BPF sample of using XDP's CPU redirect feature for
load balancing SKB processing to remote CPU. The sample implements the
same XDP load balancing as Suricata does which is symmetric hash based
on IP and L4 protocol, from Jesper.
7) Revert adding NULL pointer check with WARN_ON_ONCE() in __xdp_return()'s
critical path as it is ensured that the allocator is present, from Björn.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Preventing the kernel from responding to ICMP Echo Requests messages
can be useful in several ways. The sysctl parameter
'icmp_echo_ignore_all' can be used to prevent the kernel from
responding to IPv4 ICMP echo requests. For IPv6 pings, such
a sysctl kernel parameter did not exist.
Add the ability to prevent the kernel from responding to IPv6
ICMP echo requests through the use of the following sysctl
parameter : /proc/sys/net/ipv6/icmp/echo_ignore_all.
Update the documentation to reflect this change.
Signed-off-by: Virgile Jarry <virgile@acceis.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows a BPF_PROG_TYPE_SK_REUSEPORT bpf prog to select a
SO_REUSEPORT sk from a BPF_MAP_TYPE_REUSEPORT_ARRAY introduced in
the earlier patch. "bpf_run_sk_reuseport()" will return -ECONNREFUSED
when the BPF_PROG_TYPE_SK_REUSEPORT prog returns SK_DROP.
The callers, in inet[6]_hashtable.c and ipv[46]/udp.c, are modified to
handle this case and return NULL immediately instead of continuing the
sk search from its hashtable.
It re-uses the existing SO_ATTACH_REUSEPORT_EBPF setsockopt to attach
BPF_PROG_TYPE_SK_REUSEPORT. The "sk_reuseport_attach_bpf()" will check
if the attaching bpf prog is in the new SK_REUSEPORT or the existing
SOCKET_FILTER type and then check different things accordingly.
One level of "__reuseport_attach_prog()" call is removed. The
"sk_unhashed() && ..." and "sk->sk_reuseport_cb" tests are pushed
back to "reuseport_attach_prog()" in sock_reuseport.c. sock_reuseport.c
seems to have more knowledge on those test requirements than filter.c.
In "reuseport_attach_prog()", after new_prog is attached to reuse->prog,
the old_prog (if any) is also directly freed instead of returning the
old_prog to the caller and asking the caller to free.
The sysctl_optmem_max check is moved back to the
"sk_reuseport_attach_filter()" and "sk_reuseport_attach_bpf()".
As of other bpf prog types, the new BPF_PROG_TYPE_SK_REUSEPORT is only
bounded by the usual "bpf_prog_charge_memlock()" during load time
instead of bounded by both bpf_prog_charge_memlock and sysctl_optmem_max.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
IPv6 GRO over GRE tap is not working while GRO is not set
over the native interface.
gro_list_prepare function updates the same_flow variable
of existing sessions to 1 if their mac headers match the one
of the incoming packet.
same_flow is used to filter out non-matching sessions and keep
potential ones for aggregation.
The number of bytes to compare should be the number of bytes
in the mac headers. In gro_list_prepare this number is set to
be skb->dev->hard_header_len. For GRE interfaces this hard_header_len
should be as it is set in the initialization process (when GRE is
created), it should not be overridden. But currently it is being overridden
by the value that is actually supposed to represent the needed_headroom.
Therefore, the number of bytes compared in order to decide whether the
the mac headers are the same is greater than the length of the headers.
As it's documented in netdevice.h, hard_header_len is the maximum
hardware header length, and needed_headroom is the extra headroom
the hardware may need.
hard_header_len is basically all the bytes received by the physical
till layer 3 header of the packet received by the interface.
For example, if the interface is a GRE tap then the needed_headroom
should be the total length of the following headers:
IP header of the physical, GRE header, mac header of GRE.
It is often used to calculate the MTU of the created interface.
This patch removes the override of the hard_header_len, and
assigns the calculated value to needed_headroom.
This way, the comparison in gro_list_prepare is really of
the mac headers, and if the packets have the same mac headers
the same_flow will be set to 1.
Performance testing: 45% higher bandwidth.
Measuring bandwidth of single-stream IPv4 TCP traffic over IPv6
GRE tap while GRO is not set on the native.
NIC: ConnectX-4LX
Before (GRO not working) : 7.2 Gbits/sec
After (GRO working): 10.5 Gbits/sec
Signed-off-by: Maria Pasechnik <mariap@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using an ip6tnl device in collect_md mode, the xmit methods ignore
the ipv6.src field present in skb_tunnel_info's key, both for route
calculation purposes (flowi6 construction) and for assigning the
packet's final ipv6h->saddr.
This makes it impossible specifying a desired ipv6 local address in the
encapsulating header (for example, when using tc action tunnel_key).
This is also not aligned with behavior of ipip (ipv4) in collect_md
mode, where the key->u.ipv4.src gets used.
Fix, by assigning fl6.saddr with given key->u.ipv6.src.
In case ipv6.src is not specified, ip6_tnl_xmit uses existing saddr
selection code.
Fixes: 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-08-07
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add cgroup local storage for BPF programs, which provides a fast
accessible memory for storing various per-cgroup data like number
of transmitted packets, etc, from Roman.
2) Support bpf_get_socket_cookie() BPF helper in several more program
types that have a full socket available, from Andrey.
3) Significantly improve the performance of perf events which are
reported from BPF offload. Also convert a couple of BPF AF_XDP
samples overto use libbpf, both from Jakub.
4) seg6local LWT provides the End.DT6 action, which allows to
decapsulate an outer IPv6 header containing a Segment Routing Header.
Adds this action now to the seg6local BPF interface, from Mathieu.
5) Do not mark dst register as unbounded in MOV64 instruction when
both src and dst register are the same, from Arthur.
6) Define u_smp_rmb() and u_smp_wmb() to their respective barrier
instructions on arm64 for the AF_XDP sample code, from Brian.
7) Convert the tcp_client.py and tcp_server.py BPF selftest scripts
over from Python 2 to Python 3, from Jeremy.
8) Enable BTF build flags to the BPF sample code Makefile, from Taeung.
9) Remove an unnecessary rcu_read_lock() in run_lwt_bpf(), from Taehee.
10) Several improvements to the README.rst from the BPF documentation
to make it more consistent with RST format, from Tobin.
11) Replace all occurrences of strerror() by calls to strerror_r()
in libbpf and fix a FORTIFY_SOURCE build error along with it,
from Thomas.
12) Fix a bug in bpftool's get_btf() function to correctly propagate
an error via PTR_ERR(), from Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
According to RFC791, 68 bytes is the minimum size of IPv4 datagram every
device must be able to forward without further fragmentation while 576
bytes is the minimum size of IPv4 datagram every device has to be able
to receive, so in ip6_tnl_xmit(), 68(IPV4_MIN_MTU) should be the right
value for the ipv4 min mtu check in ip6_tnl_xmit.
While at it, change to use max() instead of if statement.
Fixes: c9fefa0819 ("ip6_tunnel: get the min mtu properly in ip6_tnl_xmit")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the callers of ip6_rt_copy_init()/rt6_set_from() hold refcnt
of the "from" fib6_info, so there is no need to hold fib6_metrics
refcnt again, because fib6_metrics refcnt is only released when
fib6_info is gone, that is, they have the same life time, so the
whole fib6_metrics refcnt can be removed actually.
This fixes a kmemleak warning reported by Sabrina.
Fixes: 93531c6743 ("net/ipv6: separate handling of FIB entries from dst based routes")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
don't bother with pathological cases, they only waste cycles.
IPv6 requires a minimum MTU of 1280 so we should never see fragments
smaller than this (except last frag).
v3: don't use awkward "-offset + len"
v2: drop IPv4 part, which added same check w. IPV4_MIN_MTU (68).
There were concerns that there could be even smaller frags
generated by intermediate nodes, e.g. on radio networks.
Cc: Peter Oskolkov <posk@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to TCP OOO RX queue, it makes sense to use rb trees to store
IP fragments, so that OOO fragments are inserted faster.
Tested:
- a follow-up patch contains a rather comprehensive ip defrag
self-test (functional)
- ran neper `udp_stream -c -H <host> -F 100 -l 300 -T 20`:
netstat --statistics
Ip:
282078937 total packets received
0 forwarded
0 incoming packets discarded
946760 incoming packets delivered
18743456 requests sent out
101 fragments dropped after timeout
282077129 reassemblies required
944952 packets reassembled ok
262734239 packet reassembles failed
(The numbers/stats above are somewhat better re:
reassemblies vs a kernel without this patchset. More
comprehensive performance testing TBD).
Reported-by: Jann Horn <jannh@google.com>
Reported-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a ICMPV6_PKT_TOOBIG is received from a link local address the pmtu will
be updated on a route with an arbitrary interface index. Subsequent packets
sent back to the same link local address may therefore end up not
considering the updated pmtu.
Current behavior breaks TAHI v6LC4.1.4 Reduce PMTU On-link. Referring to RFC
1981: Section 3: "Note that Path MTU Discovery must be performed even in
cases where a node "thinks" a destination is attached to the same link as
itself. In a situation such as when a neighboring router acts as proxy [ND]
for some destination, the destination can to appear to be directly
connected but is in fact more than one hop away."
Using the interface index from the incoming ICMPV6_PKT_TOOBIG when updating
the pmtu.
Signed-off-by: Georg Kohmann <geokohma@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit df18b50448.
This change causes other problems and use-after-free situations as
found by syzbot.
Signed-off-by: David S. Miller <davem@davemloft.net>
The construction "net->ipv4.sysctl_ip_nonlocal_bind || inet->freebind
|| inet->transparent" is present three times and its IPv6 counterpart
is also present three times. We introduce two small helpers to
characterize these tests uniformly.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
The seg6local LWT provides the End.DT6 action, which allows to
decapsulate an outer IPv6 header containing a Segment Routing Header
(SRH), full specification is available here:
https://tools.ietf.org/html/draft-filsfils-spring-srv6-network-programming-05
This patch adds this action now to the seg6local BPF
interface. Since it is not mandatory that the inner IPv6 header also
contains a SRH, seg6_bpf_srh_state has been extended with a pointer to
a possible SRH of the outermost IPv6 header. This helps assessing if the
validation must be triggered or not, and avoids some calls to
ipv6_find_hdr.
v3: s/1/true, s/0/false for boolean values
v2: - changed true/false -> 1/0
- preempt_enable no longer called in first conditional block
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Since commit d4ead6b34b ("net/ipv6: move metrics from dst to
rt6_info"), ipv6 metrics are shared and refcounted. rt6_set_from()
assigns the rt->from pointer and increases the refcount on from's
metrics. This reference is never released.
Introduce the fib6_metrics_release() helper and use it to release the
metrics.
Fixes: d4ead6b34b ("net/ipv6: move metrics from dst to rt6_info")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When freebind feature is set of an IPv6 socket, any source address can
be used when sending UDP datagrams using IPv6 PKTINFO ancillary
message. Global non-local bind feature was added in commit
35a256fee5 ("ipv6: Nonlocal bind") for IPv6. This commit also allows
IPv6 source address spoofing when non-local bind feature is enabled.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2018-07-27
1) Extend the output_mark to also support the input direction
and masking the mark values before applying to the skb.
2) Add a new lookup key for the upcomming xfrm interfaces.
3) Extend the xfrm lookups to match xfrm interface IDs.
4) Add virtual xfrm interfaces. The purpose of these interfaces
is to overcome the design limitations that the existing
VTI devices have.
The main limitations that we see with the current VTI are the
following:
VTI interfaces are L3 tunnels with configurable endpoints.
For xfrm, the tunnel endpoint are already determined by the SA.
So the VTI tunnel endpoints must be either the same as on the
SA or wildcards. In case VTI tunnel endpoints are same as on
the SA, we get a one to one correlation between the SA and
the tunnel. So each SA needs its own tunnel interface.
On the other hand, we can have only one VTI tunnel with
wildcard src/dst tunnel endpoints in the system because the
lookup is based on the tunnel endpoints. The existing tunnel
lookup won't work with multiple tunnels with wildcard
tunnel endpoints. Some usecases require more than on
VTI tunnel of this type, for example if somebody has multiple
namespaces and every namespace requires such a VTI.
VTI needs separate interfaces for IPv4 and IPv6 tunnels.
So when routing to a VTI, we have to know to which address
family this traffic class is going to be encapsulated.
This is a lmitation because it makes routing more complex
and it is not always possible to know what happens behind the
VTI, e.g. when the VTI is move to some namespace.
VTI works just with tunnel mode SAs. We need generic interfaces
that ensures transfomation, regardless of the xfrm mode and
the encapsulated address family.
VTI is configured with a combination GRE keys and xfrm marks.
With this we have to deal with some extra cases in the generic
tunnel lookup because the GRE keys on the VTI are actually
not GRE keys, the GRE keys were just reused for something else.
All extensions to the VTI interfaces would require to add
even more complexity to the generic tunnel lookup.
So to overcome this, we developed xfrm interfaces with the
following design goal:
It should be possible to tunnel IPv4 and IPv6 through the same
interface.
No limitation on xfrm mode (tunnel, transport and beet).
Should be a generic virtual interface that ensures IPsec
transformation, no need to know what happens behind the
interface.
Interfaces should be configured with a new key that must match a
new policy/SA lookup key.
The lookup logic should stay in the xfrm codebase, no need to
change or extend generic routing and tunnel lookups.
Should be possible to use IPsec hardware offloads of the underlying
interface.
5) Remove xfrm pcpu policy cache. This was added after the flowcache
removal, but it turned out to make things even worse.
From Florian Westphal.
6) Allow to update the set mark on SA updates.
From Nathan Harold.
7) Convert some timestamps to time64_t.
From Arnd Bergmann.
8) Don't check the offload_handle in xfrm code,
it is an opaque data cookie for the driver.
From Shannon Nelson.
9) Remove xfrmi interface ID from flowi. After this pach
no generic code is touched anymore to do xfrm interface
lookups. From Benedict Wong.
10) Allow to update the xfrm interface ID on SA updates.
From Nathan Harold.
11) Don't pass zero to ERR_PTR() in xfrm_resolve_and_create_bundle.
From YueHaibing.
12) Return more detailed errors on xfrm interface creation.
From Benedict Wong.
13) Use PTR_ERR_OR_ZERO instead of IS_ERR + PTR_ERR.
From the kbuild test robot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2018-07-27
1) Fix PMTU handling of vti6. We update the PMTU on
the xfrm dst_entry which is not cached anymore
after the flowchache removal. So update the
PMTU of the original dst_entry instead.
From Eyal Birger.
2) Fix a leak of kernel memory to userspace.
From Eric Dumazet.
3) Fix a possible dst_entry memleak in xfrm_lookup_route.
From Tommi Rantala.
4) Fix a skb leak in case we can't call nlmsg_multicast
from xfrm_nlmsg_multicast. From Florian Westphal.
5) Fix a leak of a temporary buffer in the error path of
esp6_input. From Zhen Lei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported a read beyond the end of the skb head when returning
IPV6_ORIGDSTADDR:
BUG: KMSAN: kernel-infoleak in put_cmsg+0x5ef/0x860 net/core/scm.c:242
CPU: 0 PID: 4501 Comm: syz-executor128 Not tainted 4.17.0+ #9
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x185/0x1d0 lib/dump_stack.c:113
kmsan_report+0x188/0x2a0 mm/kmsan/kmsan.c:1125
kmsan_internal_check_memory+0x138/0x1f0 mm/kmsan/kmsan.c:1219
kmsan_copy_to_user+0x7a/0x160 mm/kmsan/kmsan.c:1261
copy_to_user include/linux/uaccess.h:184 [inline]
put_cmsg+0x5ef/0x860 net/core/scm.c:242
ip6_datagram_recv_specific_ctl+0x1cf3/0x1eb0 net/ipv6/datagram.c:719
ip6_datagram_recv_ctl+0x41c/0x450 net/ipv6/datagram.c:733
rawv6_recvmsg+0x10fb/0x1460 net/ipv6/raw.c:521
[..]
This logic and its ipv4 counterpart read the destination port from
the packet at skb_transport_offset(skb) + 4.
With MSG_MORE and a local SOCK_RAW sender, syzbot was able to cook a
packet that stores headers exactly up to skb_transport_offset(skb) in
the head and the remainder in a frag.
Call pskb_may_pull before accessing the pointer to ensure that it lies
in skb head.
Link: http://lkml.kernel.org/r/CAF=yD-LEJwZj5a1-bAAj2Oy_hKmGygV6rsJ_WOrAYnv-fnayiQ@mail.gmail.com
Reported-by: syzbot+9adb4b567003cac781f0@syzkaller.appspotmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several files have extra line at end of file.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb hash for locally generated ip[v6] fragments belonging
to the same datagram can vary in several circumstances:
* for connected UDP[v6] sockets, the first fragment get its hash
via set_owner_w()/skb_set_hash_from_sk()
* for unconnected IPv6 UDPv6 sockets, the first fragment can get
its hash via ip6_make_flowlabel()/skb_get_hash_flowi6(), if
auto_flowlabel is enabled
For the following frags the hash is usually computed via
skb_get_hash().
The above can cause OoO for unconnected IPv6 UDPv6 socket: in that
scenario the egress tx queue can be selected on a per packet basis
via the skb hash.
It may also fool flow-oriented schedulers to place fragments belonging
to the same datagram in different flows.
Fix the issue by copying the skb hash from the head frag into
the others at fragmentation time.
Before this commit:
perf probe -a "dev_queue_xmit skb skb->hash skb->l4_hash:b1@0/8 skb->sw_hash:b1@1/8"
netperf -H $IPV4 -t UDP_STREAM -l 5 -- -m 2000 -n &
perf record -e probe:dev_queue_xmit -e probe:skb_set_owner_w -a sleep 0.1
perf script
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=3713014309 l4_hash=1 sw_hash=0
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=0 l4_hash=0 sw_hash=0
After this commit:
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0
Fixes: b73c3d0e4f ("net: Save TX flow hash in sock and set in skbuf on xmit")
Fixes: 67800f9b1f ("ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabel")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace calls to kmalloc followed by a memcpy with a direct call to
kmemdup.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two scenarios that we will restore deleted records. The first is
when device down and up(or unmap/remap). In this scenario the new filter
mode is same with previous one. Because we get it from in_dev->mc_list and
we do not touch it during device down and up.
The other scenario is when a new socket join a group which was just delete
and not finish sending status reports. In this scenario, we should use the
current filter mode instead of restore old one. Here are 4 cases in total.
old_socket new_socket before_fix after_fix
IN(A) IN(A) ALLOW(A) ALLOW(A)
IN(A) EX( ) TO_IN( ) TO_EX( )
EX( ) IN(A) TO_EX( ) ALLOW(A)
EX( ) EX( ) TO_EX( ) TO_EX( )
Fixes: 24803f38a5 (igmp: do not remove igmp souce list info when set link down)
Fixes: 1666d49e1d (mld: do not remove mld souce list info when set link down)
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the mode parameter for igmp/igmp6_group_added as we can get it
from first parameter.
Fixes: 6e2059b53f (ipv4/igmp: init group mode as INCLUDE when join source group)
Fixes: c7ea20c9da (ipv6/mcast: init as INCLUDE when join SSM INCLUDE group)
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Example setup:
host: ip -6 addr add dev eth1 2001:db8:104::4
where eth1 is enslaved to a VRF
switch: ip -6 ro add 2001:db8:104::4/128 dev br1
where br1 only has an LLA
ping6 2001:db8:104::4
ssh 2001:db8:104::4
(NOTE: UDP works fine if the PKTINFO has the address set to the global
address and ifindex is set to the index of eth1 with a destination an
LLA).
For ICMP, icmp6_iif needs to be updated to check if skb->dev is an
L3 master. If it is then return the ifindex from rt6i_idev similar
to what is done for loopback.
For TCP, restore the original tcp_v6_iif definition which is needed in
most places and add a new tcp_v6_iif_l3_slave that considers the
l3_slave variability. This latter check is only needed for socket
lookups.
Fixes: 9ff7438460 ("net: vrf: Handle ipv6 multicast and link-local addresses")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree:
1) No need to set ttl from reject action for the bridge family, from
Taehee Yoo.
2) Use a fixed timeout for flow that are passed up from the flowtable
to conntrack, from Florian Westphal.
3) More preparation patches for tproxy support for nf_tables, from Mate
Eckl.
4) Remove unnecessary indirection in core IPv6 checksum function, from
Florian Westphal.
5) Use nf_ct_get_tuplepr() from openvswitch, instead of opencoding it.
From Florian Westphal.
6) socket match now selects socket infrastructure, instead of depending
on it. From Mate Eckl.
7) Patch series to simplify conntrack tuple building/parsing from packet
path and ctnetlink, from Florian Westphal.
8) Fetch timeout policy from protocol helpers, instead of doing it from
core, from Florian Westphal.
9) Merge IPv4 and IPv6 protocol trackers into conntrack core, from
Florian Westphal.
10) Depend on CONFIG_NF_TABLES_IPV6 and CONFIG_IP6_NF_IPTABLES
respectively, instead of IPV6. Patch from Mate Eckl.
11) Add specific function for garbage collection in conncount,
from Yi-Hung Wei.
12) Catch number of elements in the connlimit list, from Yi-Hung Wei.
13) Move locking to nf_conncount, from Yi-Hung Wei.
14) Series of patches to add lockless tree traversal in nf_conncount,
from Yi-Hung Wei.
15) Resolve clash in matching conntracks when race happens, from
Martynas Pumputis.
16) If connection entry times out, remove template entry from the
ip_vs_conn_tab table to improve behaviour under flood, from
Julian Anastasov.
17) Remove useless parameter from nf_ct_helper_ext_add(), from Gao feng.
18) Call abort from 2-phase commit protocol before requesting modules,
make sure this is done under the mutex, from Florian Westphal.
19) Grab module reference when starting transaction, also from Florian.
20) Dynamically allocate expression info array for pre-parsing, from
Florian.
21) Add per netns mutex for nf_tables, from Florian Westphal.
22) A couple of patches to simplify and refactor nf_osf code to prepare
for nft_osf support.
23) Break evaluation on missing socket, from Mate Eckl.
24) Allow to match socket mark from nft_socket, from Mate Eckl.
25) Remove dependency on nf_defrag_ipv6, now that IPv6 tracker is
built-in into nf_conntrack. From Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The offload_handle should be an opaque data cookie for the driver
to use, much like the data cookie for a timer or alarm callback.
Thus, the XFRM stack should not be checking for non-zero, because
the driver might use that to store an array reference, which could
be zero, or some other zero but meaningful value.
We can remove the checks for non-zero because there are plenty
other attributes also being checked to see if there is an offload
in place for the SA in question.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The rol32 call is currently rotating hash but the rol'd value is
being discarded. I believe the current code is incorrect and hash
should be assigned the rotated value returned from rol32.
Detected by CoverityScan, CID#1468411 ("Useless call")
Fixes: b5facfdba1 ("ipv6: sr: Compute flowlabel for outer IPv6 header of seg6 encap mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: dlebrun@google.com
Signed-off-by: David S. Miller <davem@davemloft.net>
My randconfig builds came across an old missing dependency for ILA:
ERROR: "dst_cache_set_ip6" [net/ipv6/ila/ila.ko] undefined!
ERROR: "dst_cache_get" [net/ipv6/ila/ila.ko] undefined!
ERROR: "dst_cache_init" [net/ipv6/ila/ila.ko] undefined!
ERROR: "dst_cache_destroy" [net/ipv6/ila/ila.ko] undefined!
We almost never run into this by accident because randconfig builds
end up selecting DST_CACHE from some other tunnel protocol, and this
one appears to be the only one missing the explicit 'select'.
>From all I can tell, this problem first appeared in linux-4.9
when dst_cache support got added to ILA.
Fixes: 79ff2fc31e ("ila: Cache a route to translated address")
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo