isdbt_sb_subchannel is unsigned with 8 bits. So, it will
never be -1. Instead, any value bigger than 13 is invalid.
As is, the current code generates the following warnings:
drivers/media/dvb-frontends/dib8000.c: In function 'dib8000_set_isdbt_common_channel':
drivers/media/dvb-frontends/dib8000.c:2358:3: warning: comparison is always true due to limited range of data type [-Wtype-limits]
drivers/media/dvb-frontends/dib8000.c: In function 'dib8000_tune':
drivers/media/dvb-frontends/dib8000.c:3107:8: warning: comparison is always false due to limited range of data type [-Wtype-limits]
drivers/media/dvb-frontends/dib8000.c:3153:9: warning: comparison is always false due to limited range of data type [-Wtype-limits]
drivers/media/dvb-frontends/dib8000.c:3160:5: warning: comparison is always false
It should also be noticed that ARIB STD-B31, item
"3.15.6.8 Number of segments" at TMCC table defines the
value 15 for unused segment, and 14 as reserved.
So, better to change the check to consider any value
bigger than 13 to mean that sub-channels should be
disabled, fixing the warning and doing the right thing
even if an invalid value is filled by userspace.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dtv_property_cache is used on several places on very long lines.
On all places it is used, a long list of struct reference is done.
Instead of doing it, at the routines where it is used more than once,
replace it by one temporary var. That may help the compiler to
use a better code. It also makes easier to review the code, as the
lines becomes closer to 80 columns, making them a way clearer
to read.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* topic/r820t: (31 commits)
[media] r820t: Don't divide the IF by two
[media] r820t: disable auto gain/VGA setting
[media] rtl2832: Fix IF calculus
[media] r820t: put it into automatic gain mode
[media] r820t: Fix hp_cor filter mask
[media] r820t: fix PLL calculus
[media] r820t: Don't put it in standby if not initialized yet
[media] r820t: avoid rewrite all regs when not needed
[media] r820t: Allow disabling IMR callibration
[media] r820t: add a commented code for GPIO
[media] r820t: add IMR calibrate code
[media] r820t: proper initialize the PLL register
[media] r820t: use usleep_range()
[media] r820t: fix prefix of the r820t_read() function
[media] r820t: split the function that read cached regs
[media] r820t: better report signal strength
[media] r820t: add support for diplexer
[media] r820t: Show the read data in the bit-reversed order
[media] r820t: use the second table for 7MHz
[media] r820t: Invert bits for read ops
...
The intend of this patch is to improve the support of the dib0090 tuner.
The ramp tables have been updated. Also some minor enhancements has been
added (EFUSE and reset).
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The intend of this patch is to improve the support of the dib7000p. It is
now possible to set the minimum value for the AGC1. Also, the driver takes
into account the frequency offset introduced in the tuned frequency.
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The intend of this patch is to improve the support of the dib8000.
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@parrot.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sparse complains that these are "dubious one-bit signed bitfields" and
the comment says it was intended to be 1 and 0 instead of -1 and 0.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Spectrum is inverted. So, we need to invert it when calculating the
value for the IF register
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
DVBT_EN_BBIN should be set on both places where IF is set. So,
move it to a function and call it where needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
There are some init stuff to be done for each new tuner at the
demod code. Add the code there for r820t.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Symbol rate ratio were using a rough calculus, as the code was
limited to 32 bits arithmetic. Change it to 64 bits, in order
to better estimate the bandwidth low-pass filter on the demod.
This should reduce the noise and improve reception.
Reported-by: Hans-Peter Jansen <hpj@urpla.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using 'i' for the guard interval temporary var is a bad idea, as
'i' is generally used by "anonymous" indexes.
Let's rename modulation, fec and guard interval temp vars with
a meaningful name, as that makes easier to understand the code
and avoids cut-and-paste types of error.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Dan Carpenter <dan.carpenter@oracle.com>:
Smatch warnings:
drivers/media/dvb-frontends/mb86a20s.c:644 mb86a20s_layer_bitrate() error: buffer overflow 'state->estimated_rate' 3 <= 3
What happens there is that estimate_rate index should be the layer
number, and not the guard interval.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We're using the anonymous 'i' to indicate the layer number
on several places on the driver. That's not good, as some
cut-and-paste type of change might be doing the wrong thing.
So, call it as "layer" everywhere.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using the magic number "3", use NUM_LAYERS macro
on all places that are related to the ISDB-T layers.
This makes the source code a little more readable.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hauppauge Nova-S-Plus DVB-S model 92001 does not lock on horizontal
polarisation. According with the info provided at the BZ, model
92002 does.
The difference is that, on model 92001, the tone select is done via
isl6421, while, on other devices, this is done via cx24123 code.
This patch adds a way to override the demod's set_tone at isl6421
driver. In order to avoid regressions, the override is enabled
only for cx88 Nova S plus model 92001. For all other models and
devices, the set_tone is provided by the demod driver.
Patch originally proposed at bz@9476[1] by Michel Meyers and
John Donoghue but applying the original patch would break support
for all other devices based on isl6421.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=9476
Tested-by: Adam Sampson <ats@offog.org>
Tested-by: Hans-Peter Jansen <hpj@urpla.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
au8522_attach is dependent on CONFIG_DVB_AU8522_DTV, not CONFIG_DVB_AU8522.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that au0828 has been converted to the control framework these
compatilibity ops are no longer needed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Last parameter of function GetLockStatus() isn't used so drop it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changeset 8f3741e accidentally broke the CNR estimation. It should
be calculated as "a + b - c". However, previously, the subtraction
by c only occurred if SNR would be positive, due to a bad binding
to DVBv3 API.
This also fixes the following warning:
drivers/media/dvb-frontends/drxk_hard.c:2556:6: warning: variable 'c' set but not used [-Wunused-but-set-variable]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use register address auto increment to reduce I/O when large
register / values tables are written.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That register is property of demodulator so move it correct place.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those are demodulator init tables according to used tuner tuner
config. af9033 demod driver does those inits currently and due
to that these duplicate inits could be removed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dumped out from the Windows driver version 12.07.06.1
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dumped out from the Windows driver version 12.07.06.1
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dumped out from the Windows driver version 12.07.06.1
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dumped out from the Windows driver version 12.07.06.1
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dumped out from the Windows driver version 12.07.06.1
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dumped out from the Windows driver version 12.07.06.1
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dumped out from Windows driver version 12.07.06.1, 07/06/2012.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for tuners integrated to the IT9135 and IT9137.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Kconfig entry for "TS2020 based tuners" defaults to modular if
DVB_FE_CUSTOMISE is set. But that Kconfig symbol was replaced with
MEDIA_SUBDRV_AUTOSELECT as of v3.7. So use the new symbol. And negate
the logic, so we are in line with all the similar entries in this file.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The DVBv3 signal strength indicator is bogus: it doesn't range
from 0 to 65535 as it would be expected. Also, 0 means the max
signal strength.
Now that a better way to estimate it was added, use the new
way.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The AZ6007 driver released by Terratec has a better way to
estimate the signal strength, at CtrlSigStrength(). Port it
to the driver.
It should be noticed that there are two parameters there that
are tuner-specific.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original az6007 driver has the code to calculate such
stats. Add it to the driver, reporting them via DVBv5
stats API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
goto err and goto err_gateoff before mutex_lock(&state->internal->demod_lock)
lead to unlock of unheld mutex in stv090x_sleep().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that some devices initialize register 0x2a with different
values, add the calculus formula, instead of hardcoding it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Up to now, the driver was simply assuming TV mode, 13 segs.
Implement the logic to control the ISDB operational mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signal strength is always available. There's no reason to reset
it, as it has its own logic to reset it already.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Always init the frontend when set_frontend is called. The rationale
is: it was noticed that, on some devices, it fails to lock with a
different channel. It seems that some other registers need to be
restored to its initial state, when the channel changes.
As it is better to reset everything, even wasting a few more
miliseconds than to loose channel lock, let's change the logic
to always reset.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the AGC settings present on a newer device.
The initial settings were taken from one of the first devices with
mb86a20s, and there are several reports that this is not working
properly on some places.
So, instead of keeping using it, get the parameters taken from a
newer device. Tests are welcomed.
Tested also with cx231xx PixelView SBTVD Hybrid with no regressions
noticed so far.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
State 9 means TS started to be output, and it should be
associated with FE_HAS_SYNC.
The mb86a20scan get CNR statistics at state 7, when frame sync
is obtained.
As CNR may help to adjust the antenna, provide it earlier.
A latter patch could eventually start outputing MER measures
earlier, but that would require a bigger change, and probably
won't be better than the current way, as the time between
changing from state 8 to 9 is generally lower than the time
to get the stats collected.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of hardcoding a fixed IF frequency of 3.3 MHz, use
the IF frequency provided by the tuner driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are a few debug tests that are shown with dev_err() or
dev_info(). Replace them by dev_dbg().
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The address of a variable is impossible to be null, so we remove the check.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces the use of IS_ENABLED() macro. For example,
replacing:
#if defined(CONFIG_I2C) || (defined(CONFIG_I2C_MODULE) && defined(MODULE))
with:
#if IS_ENABLED(CONFIG_I2C)
All changes made by this patch respect the same replacement pattern.
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sometimes there is a problem when trying to access the non-existing registers
of the second demodulator path on the STV0903.
This change removes the calls in case the driver is used on a STV0903.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The logic that resets the device is wrong. It should be resetting
just the layer that got read. Also, stop is needed before updating
the counters.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The logic that resets the device is wrong. It should be resetting
just the layer that got read. Also, stop is needed before updating
the counters.
While there, rename it, as we'll soon introduce a postBER logic
there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add both per-layer and global block error count and block count,
for PER and UCB measurements.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add Signal/Noise ratio measurement. On this device, a global measure
is taken by the demod. It also provides per-layer CNR measurements,
based on Modulation Error measures (MER).
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do a better job on setting the bit error counters, in order to
have all layer measures to happen in a little less than one
second.
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the methods to read bit error/bit count measurements from
mb86a20s. On ISDB-T devices, those reads are done per layer.
However, as userspace applications may not be aware of that,
add a global measure that will sum the bit errors and bit
counts for each layer, storing them into a global value.
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of providing separate callbacks to read the several FE
stats properties, the better seems to use just one method that will:
- Read lock status;
- Read signal strength;
- if locked, get TMCC data;
- if locked, get DVB statistics.
As the DVB frontend thread will call this read_status callback
on every 3 seconds, and userspace can even call it earlier,
all stats data and layers layout will be updated together if
available, with is a good thing.
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Feng's kbuild test:
From: kbuild test robot <fengguang.wu@intel.com>
Subject: drivers/media/dvb-frontends/mb86a20s.c:706 mb86a20s_attach() error: potential null dereference 'state'. (kzalloc returns null)
Date: Wed, 23 Jan 2013 19:30:43 +0800
commit: f66d81b54d [media] mb86a20s: convert it to use dev_info/dev_err/dev_dbg
drivers/media/dvb-frontends/mb86a20s.c:706 mb86a20s_attach() error: potential null dereference 'state'. (kzalloc returns null)
drivers/media/dvb-frontends/mb86a20s.c:706 mb86a20s_attach() error: we previously assumed 'state' could be null (see line 705)
As, at mb86a20s_attach(), we have an i2c pointer, use it for all printk
messages there, instead of state->i2c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having its own set of macros, use the Kernel default
ones for debug, error and info.
While here, do some cleanup on the debug printk's.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reorder functions to have everything related to stats/status read
close. That will make the file more organized as other stats
routines will be added.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Split the logic that reads the status from the DVB callback. That
helps to properly return an error code, if status read fails.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The read/write errors are not handled well on get_frontend. Fix it,
by letting the frontend cached values to represent the DVB properties
that were successfully retrieved.
While here, use "c" for dtv_frontend_properties cache, instead of
"p", as this is more common.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multistream support for stv0900. For Netup Dual S2 CI with STV0900BAC/AAC.
Signed-off-by: Evgeny Plehov <EvgenyPlehov@ukr.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Restore ds3000.c read_signal_strength.
Call tuner get_rf_strength from frontend read_signal_strength.
We are able to do a NULL check and doesn't limit the tuner
attach to the frontend attach area.
At the moment the lmedm04 tuner attach is stuck in frontend
attach area.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Various small changes and fixes releated to dual mode.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tuner part of Montage rs2000 chip is similar to ts2020 tuner.
Patch to use ts2020 code.
[mchehab@redhat.com: a few CodingStyle fixes]
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
TeVii s660 and others have LED for lock indication.
Let's use it in right order.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
One register needs to be changed to TS to work. So we use separate inittab.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Acked-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- if kmalloc() returns NULL, we can return immediately without trying
to kfree() a NULL pointer.
- if i2c_transfer() fails, error out immediately instead of trying to
upload the remaining bytes of the firmware.
- the error code is then properly propagated down to ds3000_initfe().
Signed-off-by: Rémi Cardona <remi.cardona@smartjog.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/ts2020.c: In function 'ts2020_set_params':
drivers/media/dvb-frontends/ts2020.c:126:47: warning: variable 'div4' set but not used [-Wunused-but-set-variable]
drivers/media/dvb-frontends/ts2020.c: At top level:
drivers/media/dvb-frontends/ts2020.c:262:5: warning: no previous prototype for 'ts2020_get_signal_strength' [-Wmissing-prototypes]
Cc: Konstantin Dimitrov <kosio.dimitrov@gmail.com>
Cc: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
make the other drivers take use of the separate ts2020 driver
Signed-off-by: Konstantin Dimitrov <kosio.dimitrov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
remove ts2020 tuner related code from ds3000 driver
prepare ds3000 driver for using external tuner driver
Signed-off-by: Konstantin Dimitrov <kosio.dimitrov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Found by coccinelle. Hand patched and reviewed.
Tested by compilation only.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier struct_name;
struct struct_name to;
struct struct_name from;
expression E;
@@
-memcpy(&(to), &(from), E);
+to = from;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Previously, gate control didn't work until drxd_init()
execution. Migrate necessary set of commands in drxd_attach
to allow gate control to be used by tuner which are
accessible through i2c gate.
Reported-by: frederic.mantegazza@gbiloba.org
Signed-off-by: Patrice Chotard <patricechotard@free.fr>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQ1QqgAAoJEHm+PkMAQRiG3GMIAJZjN2+0EGFpcq0LDrjIMyLG
PFuCkn9wNybAVR38DuVJkYclLclN2T1CevWZib+GgRLZO2IU5Qu1xh+fCLRn1u5i
qrxq8g4HYVMYXDixdZzXA2eXCLF7YLzPEdlowoBItGl9OJjQdzk3zBATtJGxfKaP
zvmaXP0CyoQekrZmmpMEl2/PLY/X0Ett6I5tlKcTvYKbbowG1SoAwVEVokCZC/vi
I+y8/8M68eDfOfYZ8BoRd5Lsygxfw8uvOce4qUeKawiZPO8bWP1s9NFyK6Ank6+s
hNXM9dNm6l0JfS+Ykb2FXleuEmOaaloRswOxukU1gKC3V0HdxwKx0Ir4P3z1dHM=
=5Iln
-----END PGP SIGNATURE-----
Merge tag 'v3.8-rc1' into staging/for_v3.9
Linux 3.8-rc1
* tag 'v3.8-rc1': (10696 commits)
Linux 3.8-rc1
Revert "nfsd: warn on odd reply state in nfsd_vfs_read"
ARM: dts: fix duplicated build target and alphabetical sort out for exynos
dm stripe: add WRITE SAME support
dm: remove map_info
dm snapshot: do not use map_context
dm thin: dont use map_context
dm raid1: dont use map_context
dm flakey: dont use map_context
dm raid1: rename read_record to bio_record
dm: move target request nr to dm_target_io
dm snapshot: use per_bio_data
dm verity: use per_bio_data
dm raid1: use per_bio_data
dm: introduce per_bio_data
dm kcopyd: add WRITE SAME support to dm_kcopyd_zero
dm linear: add WRITE SAME support
dm: add WRITE SAME support
dm: prepare to support WRITE SAME
dm ioctl: use kmalloc if possible
...
Conflicts:
MAINTAINERS
Building budget-av.o triggers this GCC warning:
In file included from drivers/media/pci/ttpci/budget-av.c:44:0:
drivers/media/dvb-frontends/tda8261_cfg.h: In function ‘tda8261_get_bandwidth’:
drivers/media/dvb-frontends/tda8261_cfg.h:68:21: warning: ‘t_state.bandwidth’ may be used uninitialized in this function [-Wuninitialized]
Move the printk() that uses t_state.bandwith to the location where it
should be initialized to fix this.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
display an error message if either tuner_i2c_addr or demod_i2c_addr
are not specified in the tda10071_config structure
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The default i2c address for the tuner is 0x14,
allow this to be overridden with a configuration parameter
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media updates from Mauro Carvalho Chehab:
- Missing MAINTAINERS entries were added for several drivers
- Adds V4L2 support for DMABUF handling, allowing zero-copy buffer
sharing between V4L2 devices and GPU
- Got rid of all warnings when compiling with W=1 on x86
- Add a new driver for Exynos hardware (s3c-camif)
- Several bug fixes, cleanups and driver improvements
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (243 commits)
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] omap3isp: Prepare/unprepare clocks before/after enable/disable
[media] omap3isp: preview: Add support for 8-bit formats at the sink pad
[media] omap3isp: Replace printk with dev_*
[media] omap3isp: Find source pad from external entity
[media] omap3isp: Configure CSI-2 phy based on platform data
[media] omap3isp: Add PHY routing configuration
[media] omap3isp: Add CSI configuration registers from control block to ISP resources
[media] omap3isp: Remove unneeded module memory address definitions
[media] omap3isp: Use monotonic timestamps for statistics buffers
[media] uvcvideo: Fix control value clamping for unsigned integer controls
[media] uvcvideo: Mark first output terminal as default video node
[media] uvcvideo: Add VIDIOC_[GS]_PRIORITY support
[media] uvcvideo: Return -ENOTTY for unsupported ioctls
[media] uvcvideo: Set device_caps in VIDIOC_QUERYCAP
[media] uvcvideo: Don't fail when an unsupported format is requested
[media] uvcvideo: Return -EACCES when trying to access a read/write-only control
[media] uvcvideo: Set error_idx properly for extended controls API failures
[media] rtl28xxu: add NOXON DAB/DAB+ USB dongle rev 2
[media] fc2580: write some registers conditionally
...
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
* linus/master: (1428 commits)
futex: avoid wake_futex() for a PI futex_q
watchdog: using u64 in get_sample_period()
writeback: put unused inodes to LRU after writeback completion
mm: vmscan: check for fatal signals iff the process was throttled
Revert "mm: remove __GFP_NO_KSWAPD"
proc: check vma->vm_file before dereferencing
UAPI: strip the _UAPI prefix from header guards during header installation
include/linux/bug.h: fix sparse warning related to BUILD_BUG_ON_INVALID
Linux 3.7-rc7
powerpc/eeh: Do not invalidate PE properly
ALSA: hda - Fix build without CONFIG_PM
of/address: sparc: Declare of_iomap as an extern function for sparc again
PM / QoS: fix wrong error-checking condition
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
MPI: Fix compilation on MIPS with GCC 4.4 and newer
MIPS: Fix crash that occurs when function tracing is enabled
MIPS: Merge overlapping bootmem ranges
jbd: Fix lock ordering bug in journal_unmap_buffer()
...
Since b9bf2eafaa, the function
ds3000_firmware_ondemand() is called only once during init. This
locking scheme may have been useful when the firmware was loaded at
each tune.
Furthermore, it looks like this 'lock' was put in to prevent concurrent
access (and not recursion as the comments suggest). However, this open-
coded mechanism is anything but race-free and should have used a proper
mutex.
Signed-off-by: Rémi Cardona <remi.cardona@smartjog.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While it is very unlikely, if the number of parameters for
QAMDemodulatorCommand is not 2 or 4, status become undefined:
/home/hans/work/build/v4l-dvb-git/drivers/media/dvb-frontends/drxk_hard.c: In function ‘QAMDemodulatorCommand’:
/home/hans/work/build/v4l-dvb-git/drivers/media/dvb-frontends/drxk_hard.c:5452:5: warning: ‘status’ may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On gcc, enums are generally unsigned, except if a negative value
is declared. Due to that, warnings may happen there:
drivers/media/dvb-frontends/cx22700.c:142:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/media/dvb-frontends/cx22700.c:155:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/media/dvb-frontends/cx24123.c:341:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/media/dvb-frontends/l64781.c:183:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/media/dvb-frontends/l64781.c:187:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/media/dvb-frontends/mt312.c:552:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/media/dvb-frontends/mt312.c:560:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
As other compilers might be using signed values, the better is to
keep the checks there, casting the value to avoid the warning.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/drxk_hard.c:68:13: warning: 'IsA1WithPatchCode' defined but not used [-Wunused-function]
drivers/media/dvb-frontends/drxk_hard.c:73:13: warning: 'IsA1WithRomCode' defined but not used [-Wunused-function]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/tda10071.c:119:5: warning: no previous prototype for 'tda10071_rd_reg_mask' [-Wmissing-prototypes]
drivers/media/dvb-frontends/tda10071.c:99:5: warning: no previous prototype for 'tda10071_wr_reg_mask' [-Wmissing-prototypes]
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/stv0367.c:1267:25: warning: no previous prototype for 'stv0367ter_lock_algo' [-Wmissing-prototypes]
drivers/media/dvb-frontends/stv0367.c:1531:5: warning: no previous prototype for 'stv0367ter_init' [-Wmissing-prototypes]
drivers/media/dvb-frontends/stv0367.c:2381:21: warning: no previous prototype for 'stv0367cab_SetQamSize' [-Wmissing-prototypes]
drivers/media/dvb-frontends/stv0367.c:2765:5: warning: no previous prototype for 'stv0367cab_init' [-Wmissing-prototypes]
drivers/media/dvb-frontends/stv0367.c:882:4: warning: no previous prototype for 'stv0367_getbits' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/rtl2832.c:268:5: warning: no previous prototype for 'rtl2832_rd_demod_reg' [-Wmissing-prototypes]
drivers/media/dvb-frontends/rtl2832.c:308:5: warning: no previous prototype for 'rtl2832_wr_demod_reg' [-Wmissing-prototypes]
drivers/media/dvb-frontends/rtl2832.c:513:5: warning: no previous prototype for 'rtl2832_get_tune_settings' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/rtl2830.c:133:5: warning: no previous prototype for 'rtl2830_wr_reg_mask' [-Wmissing-prototypes]
drivers/media/dvb-frontends/rtl2830.c:153:5: warning: no previous prototype for 'rtl2830_rd_reg_mask' [-Wmissing-prototypes]
drivers/media/dvb-frontends/rtl2830.c:259:5: warning: no previous prototype for 'rtl2830_get_tune_settings' [-Wmissing-prototypes]
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/drxd_hard.c:1751:5: warning: no previous prototype for 'SetOperationMode' [-Wmissing-prototypes]
drivers/media/dvb-frontends/drxd_hard.c:2615:5: warning: no previous prototype for 'DRXD_init' [-Wmissing-prototypes]
drivers/media/dvb-frontends/drxd_hard.c:2777:5: warning: no previous prototype for 'DRXD_status' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dereference should be moved below the NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/drxk_hard.c:68:6: warning: no previous prototype for 'IsA1WithPatchCode' [-Wmissing-prototypes]
drivers/media/dvb-frontends/drxk_hard.c:73:6: warning: no previous prototype for 'IsA1WithRomCode' [-Wmissing-prototypes]
drivers/media/dvb-frontends/drxk_hard.c:192:12: warning: no previous prototype for 'Frac28a' [-Wmissing-prototypes]
drivers/media/dvb-frontends/drxk_hard.c:590:5: warning: no previous prototype for 'PowerUpDevice' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r1@
statement S;
position p,p1;
@@
S@p1;@p
@script:python r2@
p << r1.p;
p1 << r1.p1;
@@
if p[0].line != p1[0].line_end:
cocci.include_match(False)
@@
position r1.p;
@@
-;@p
// </smpl>
[mchehab@redhat.com: some hunks got bitroted; applied only the
ones that succeeds]
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
[crope@iki.fi: For my drivers a8293, af9013, af9015, af9035]
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As spotted by Dan Carpenter <dan.carpenter@oracle.com> (thanks!), we have
improperly used an unsigned variable in a calculation that may result in a
negative number. This may cause an unintended underflow if the interface
frequency of the tuner is > approx. 40MHz.
This patch should resolve the issue, following an approach similar to what is
used in af9013.c.
[crope@iki.fi: add Reported-by]
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to udev-182, the firmware load was changed to be async, as
otherwise udev would give up of loading a firmware.
Add an option to return to the previous behaviour, async firmware
loads cause failures with the tda18271 driver.
Antti tested it with the following hardware:
Hauppauge WinTV HVR 930C
MaxMedia UB425-TC
PCTV QuatroStick nano (520e)
Tested-by: Antti Palosaari <crope@iki.fi>
Cc: stable@kernel.org # for Kernel 3.6 - please note that driver location has changed
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is fallback condition as GPIOLIB seems to be disabled by default.
Better solution is needed, maybe GPIOLIB could be enabled by default?
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda1004x doesn't allow firmware loads while it is busy with something
else. Avoid it to happen by locking the I2C bus during firmware transfer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is initial support for the Asus MyCinema U3100Mini Plus. The driver
in its current form gets detected and loads properly.
Scanning using dvbscan works without problems, Locking onto a channel
using tzap also works fine. Only playback using tzap -r + mplayer was
tested and was fully functional.
It uses the af9035 USB Bridge chip, with an af9033 demodulator. The tuner
used is the FCI FC2580.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently there is LNA behind cxd2820r demodulator GPIO. Use
Kernel GPIO interface to access those GPIOs.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This optimizes few hundred bytes from data to text segment.
Also remove one unused function that was commented out already.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use .get_if_frequency() as all used tuner drivers
(mt2060/qt1010/mxl5005s) supports it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is first step closer to support multiple tuners.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Used IF frequency is one of the most important parameter to know.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is done as a minimal printk updating patch to ensure correctness. Yes
it should all one day use dev_foo(), but that's one for the maintainers.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=32932
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implementation taken from rtl2830.
Cc: Thomas Mair <thomas.mair86@googlemail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Am 14.08.2012 14:05, schrieb Manu Abraham:
>> My other device, a STB0899, always reports the set frequency. So it seems
>> driver dependent whether it reports the actually locked frequency found by
>> the zig-zag-algorithm or just the set frequency to tune to.
>
> The STV0299 blindly sets the value based on a software zigzag (due to simpler
> hardware), but this might not be accurate enough. On the other hand, the
> STB0899 internally does zig-zag in hardware for DVB-S2, and partly in
> software for DVB-S.
>
> In any event, the get_frontend callback should return the value that is read
> from the demodulator registers, rather than the cached original value that
> which was requested to be tuned.
>
> The stb0899 returns only the cached value IIRC. Maybe I will fix this soon,
> or maybe you can send a patch.
This is what I get after the patch:
Sat. Pol. Band Freq (MHz) Set Freq (MHz) Get Delta (MHz)
S19,2E H L 10744 10748,474 4,474
S19,2E H L 10773 10777,944 4,944
S19,2E H L 10832 10836,953 4,953
S19,2E H L 10861 10868,774 7,774
...
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let the dvb-frontend return -ENOTTY for those unimplemented IOCTLs.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having 3 options to allow customizing the media
sub-drivers (tuners, I2C drivers, frontends), merge all of
them into just one.
That simplifies the life for users, as they can just keep
this untouched.
Life for developers is also simpler, as there's now just
one Kconfig item to remember, for the ancillary sub-drivers
providing supports for chips that could change from one
board design to another.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On a few places, := were using instead of +=, causing drivers to
not compile.
While here, standardize the usage of += on all cases where multiple
lines are needed, and for obj-y/obj-m targets, and := when just one
line is needed, on <module>-obj rules.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Identified-by: Antti Polosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This code looks suspicious, but it turns out that "nv" is an array of u8
so sizeof() is the same as ARRAY_SIZE(). Using ARRAY_SIZE() is more
readable though.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the tuners one level up, as the "common" directory will be used
by drivers that are shared between more than one driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Raise the DVB frontends one level up, as the intention is to remove
the drivers/media/dvb directory.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab