- One device tree fix for all spi node to have per clock added.
The clock is needed by spi driver to calculate bit rate divisor.
The spi node in the current device trees either does not have the
clock or is defined as dummy clock, in which case the driver probe
will fail or spi will run at a wrong bit rate.
- Two imx6q clock fixes, which correct axi_sels and ldb_di_sels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRrLClAAoJEFBXWFqHsHzO7mIH/0zrRS+0aOdrrdL6pPWW+dua
b1q5xk7vU3LU57SN6WozsfoR5zWiO3qCK5R7wvT1eYFamDryUmlNsTiFz2XG8ZdK
qYVegCh86UqteSJYRBBYAuNcBjkKryPUP+Iy2PJuZKmrwNKhFfdoYYFh68th0Dc8
UcIv999Jm0JswfQ8Av4idSSMWtPwwyBm3dBEa3nI/pDdj2Wg9UmWXFml36wiEYyd
CUdlcY4UenBvPIAXq0UwH4vD65Bkuz7XQqjuLtP7rgwJmVdedXYOLv59Cka5FBR9
cZoeoKl9lm+7fJVfWwTtMiW1jmE+nOh/cmCZN9aE/T1xWu8dl29h6nCOXUFCbfI=
=sjAQ
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.10-2' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo, imx fixes for 3.10, take 2:
- One device tree fix for all spi node to have per clock added.
The clock is needed by spi driver to calculate bit rate divisor.
The spi node in the current device trees either does not have the
clock or is defined as dummy clock, in which case the driver probe
will fail or spi will run at a wrong bit rate.
- Two imx6q clock fixes, which correct axi_sels and ldb_di_sels.
* tag 'imx-fixes-3.10-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: clk-imx6q: AXI clock select index is incorrect
ARM: dts: imx: fix clocks for cspi
ARM i.MX6q: fix for ldb_di_sels
Signed-off-by: Olof Johansson <olof@lixom.net>
If the early MMU mapping of the UART happens to get booted out of the
TLB between the start of paging_init() and when we finally re-add the
UART at the very end of s3c_init_cpu(), we'll get a hang at bootup if
we've got early_printk enabled. Avoid this hang by calling
debug_ll_io_init() early.
Without this patch, you can reliably reproduce a hang when early
printk is enabled by adding flush_tlb_all() at the start of
exynos_init_io(). After this patch the hang goes away.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Correction to USB OVC and PENC pin groupings on r8a7779 SoC.
This avoids conflicts when the USB_OVCn pins are used by another function.
This has been observed to be a problem in v3.10-rc1.
* Update CMT clock rating for sh73a0 SoC to resolve boot failure
on kzm9g-reference. This resolves a regression between v3.9 and v3.10-rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRrZpLAAoJENfPZGlqN0++t0UQAIBErmUK+bGdZ21NmWmjIMb3
mOegzj53Fvl3nWixPqYEGOSBEMtAltL4BnuEIJ5cC4jIijHYn9YtAfGQYSmgyV4+
KxloM8ZpJ6deGsKC5NyPnq9Hf+8Qec44LxQRuZxh58gchZFoUn2DAZBCBeLYlSs1
t2BHBD4aMaI6VYfMpBOaSPNn7oCds2kzqQ7pkiLkLdUWw1pnfxkWzBB+4+JYCOx1
BqfwgoxuhHSf7J9W2sb4EakDh19ZjBPfcjdS/DJOSk3Q6WyhkyaC6VkdYiVXekWg
tcedXxB4QavDkDiAje1/z9gBJHnE58ZKB+Q3MakHgwunhr5wMBzS1Hk62ybcPW+W
fUzhzmJd/BLxfzAJbguNoGistWmY6qcf8F2Zvx6VyI+X+BK4OulZvJzle4t5mDu6
GdYXRYP/dX9IuMrA5i5uemYF3/7Qj+CXkyO+6r6baGSBub9rE+dDI15Zjzm7en8n
DpSji9h2gvmN3jJ5fq22MikRegk+UyMGahr3P7DqgJdv6SPNGVe5cEJRLrijYojM
qC9MCyh4Jnai0NRnFoIf4+DhF3/fqbmgcBCOINDpkisf1u7Qxrm10c7kFHngu20w
ub9xhHq3hYgzcwn4rk/c/H5deWdOj5LoKM+ddy4isihbCOKtcPrOVHTWSnGuL+th
hnXe/GxU9Tyq0yF+JgT7
=oukw
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman, Renesas ARM based SoC fixes for v3.10:
- Correction to USB OVC and PENC pin groupings on r8a7779 SoC.
This avoids conflicts when the USB_OVCn pins are used by another function.
This has been observed to be a problem in v3.10-rc1.
- Update CMT clock rating for sh73a0 SoC to resolve boot failure
on kzm9g-reference. This resolves a regression between v3.9 and v3.10-rc1.
* tag 'renesas-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: sh73a0: Update CMT clockevent rating to 80
sh-pfc: r8a7779: Don't group USB OVC and PENC pins
Signed-off-by: Olof Johansson <olof@lixom.net>
Printing low-level debug messages make an assumption that the specified
UART port has been preconfigured by the bootloader. Incorrectly
specified UART port results in system getting stalled while printing the
message "Uncompressing Linux... done, booting the kernel"
This UART port number is specified through S3C_LOWLEVEL_UART_PORT. Since
the UART port might different for different board, it is not possible to
specify it correctly for every board that use a common defconfig file.
Calling this print subroutine only when DEBUG_LL fixes the problem. By
disabling DEBUG_LL in default config file, we would be able to boot
multiple boards with different default UART ports.
With this current approach, we miss the print "Uncompressing Linux...
done, booting the kernel." when DEBUG_LL is not defined.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Also fixes some CCF-related breakage on OMAP36xx/37xx, affecting DSS
at the very least.
Basic test logs for this branch are here:
http://www.pwsan.com/omap/testlogs/fixes_b_v3.10-rc/20130606093449/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HWUH
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-b-for-3.10-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.10/fixes
More OMAP hwmod and clock fixes for v3.10-rc. Fixes the AM33xx UART2.
Also fixes some CCF-related breakage on OMAP36xx/37xx, affecting DSS
at the very least.
Basic test logs for this branch are here:
http://www.pwsan.com/omap/testlogs/fixes_b_v3.10-rc/20130606093449/
omap36xx_pwrdn_clk_enable_with_hsdiv_restore expects the parent hw of
the clock to be a clk_hw_omap. However, looking at cclock3xxx_data.c,
all concerned clock have parent defined as clk_divider. Fix the
function to use clk_divider. Tested with 3.9 on dm3730.
Signed-off-by: Jean-Philippe François <jp.francois@cynove.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Update the CMT clockevent rating from 125 to 80.
This resolves a boot-failure regression for kzm9g-reference in v3.10-rc1
introduced by f7db706b13 ("ARM: 7674/1: smp:
Avoid dummy clockevent being preferred over real").
The patch noted above reduces the rating of dummy clockevent from 400 to 100.
This patch reduces the rating of CMT so that it is once again less than that
of the dummy clockevent.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
OMAP5 has 6 timers (GPTimers 5, 6, 8 to 11) that are capable of PWM.
The PWM capability property is missing from the node definitions of
couple of timers.
Add ti,timer-pwm attribute for timer 5, 6, 8 and 11.
Signed-off-by: Suman Anna <s-anna@ti.com>
[benoit.cousson@linaro.org: Update changelog and subject to highlight
the fix]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Earlier commits ensured proper muxing of pins related to proper
TWL6030 behavior: see commit 265a2bc8 (ARM: OMAP3: TWL4030: ensure
sys_nirq1 is mux'd and wakeup enabled) and commit 1ef43369 (ARM:
OMAP4: TWL: mux sys_drm_msecure as output for PMIC).
However these only fixed legacy boot and not DT boot. For DT boot,
the default mux values need to be set properly in DT.
Special thanks to Nishanth Menon for the review and catching some
major flaws in earlier versions.
Tested on OMAP4430/Panda and OMAP4460/Panda-ES.
Cc: Nishanth Menon <nm@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
[benoit.cousson@linaro.org: Slightly change the subject to align
board name with file name]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The gpmc driver is actually looking for "gpmc,num-cs" and
"gpmc,num-waitpins" properties in DT. The binding doc also states
this.
Correct the properties in the dts to provide the right values for the
gpmc driver.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The UART2 hwmod structure is pointing to the EDMA channels of UART1,
which doesn't look right. This patch fixes this by making the UART2
hwmod structure to a new structure that lists the EDMA channels to be
used by the UART2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
- A multiplatform fix making sure ux500_idle_init() is only
executed on ux500.
- A regulator fix making sure the MMC/SD card regulator is
not disabled on boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=lIoL
-----END PGP SIGNATURE-----
Merge tag 'ux500-arm-soc-v3.10-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij, ux500 fixes for v3.10:
- A multiplatform fix making sure ux500_idle_init() is only executed on ux500.
- A regulator fix making sure the MMC/SD card regulator is not disabled on boot.
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'ux500-arm-soc-v3.10-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Provide supplies for AUX1, AUX2 and AUX3
ARM: ux500: Only configure wake-up reasons on ux500 based platforms
Stephen Warren reported the recent commit 78506f2 (add support for
extended FIFO-size of PL011-r1p5) breaks the serial port on the
BCM2835 ARM SoC.
A UART compatible with the ARM PL011-r1p5 should have 32-deep FIFOs.
The BCM2835 UART just looks like an ARM PL011-r1p5, but has 16-deep
FIFOs just like PL011-r1p4 or earlier revisions. As a workaround for
this compatibility issue, this patch overrides the HW UART periphid
register values with the actually compatible UART periphid 0x00241011
(r1p3 or r1p4).
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit a819c4f1 (ARM: OMAP3: PM: Only access IVA if one exists)
changed PM to not access IVA registers on omaps that don't have
them. Turns out we still need to idle iva2 as otherwise
iva2_pwrdm will stay on and block deeper idle states.
It seems that the only part of the reset that may not be needed
is the setting of the iva2 boot mode to idle. But as that register
seems to be there and is harmless if no iva2 is on the SoC, it's
probably safest to do the complete reset.
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Six patches fixing up the suspend/resume and wakeup
handling of the Samsung and Exynos drivers.
- Errorpath fixes for four different drivers. All on
the probe() errorpath.
- Make the debugfs code for pin config take the right
mutex.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJRpiV9AAoJEEEQszewGV1zMoEP/i/XS0p/KoyHvD3k4L1vw5nc
kxDjjYXYZRrNzLtqMdr+DrEITO9yArnuJQeeUlx92Aq0GCC3B/Rh1YvhkIKvqhx4
tbySQqpDaBbWt7UsixtZBBt8CxVGiD26lLbkpAECunAFgh+XA4x6dyuSbWdem+1Y
XBX56BpukU+pfa62sM9P2Hs4Cj/QQ/ABDkibzoD1tFnORdGPkcFwddXdthn37MZL
WLF14522xL1GCrwzDVDbDTHsbgooFZRI8Zv0cExnbGc+BrivcnSAnVCioACHY+Pg
+iHk1ls+rJEnZgqafEzq9ViHRx3ctyiscUyrdYS5OMoHZ4PcqcSqtgmi0YUTynwf
jNa3OXVQ4SITuj8Q1vvxwOejUD1L2GdWSij8gBIYZTKShqntdsrYj9zX6SljHd6P
x/93UpXLL9N1nbbTA/XsD1HRSYCmtHS20GH3N2hsDJa8nIQNwBD1ydj+Mzt0ROLf
pKvT7jPVSYC8lYYMrigFhNuUVir0mCKiHYPrz3H6oWTVX+YFxj7420b3mid0u5fw
mi8zfpxhLOMPnDGQnB3U2xUva4Nfshn9RLBfdBjC08H3OJnGTgjBwtfiqx6vbLqi
ZkOl/gElq9AKUOqVNT51E0G/4Nvbe/jBQqQppLDBsxQ4x8LLBIrFmInOs/IiH3wV
Q4TVoXut9HMB6YDBl2BA
=J5kT
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes-v3.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin-control fixes from Linus Walleij:
- Six patches fixing up the suspend/resume and wakeup handling of the
Samsung and Exynos drivers.
- Errorpath fixes for four different drivers. All on the probe()
errorpath.
- Make the debugfs code for pin config take the right mutex.
* tag 'pinctrl-fixes-v3.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: pinconf: take the right mutex
pinctrl: sunxi: fix error return code in sunxi_pinctrl_probe()
pinctrl: exynos: Handle suspend/resume of GPIO EINT registers
pinctrl: samsung: Allow per-bank SoC-specific private data
pinctrl: samsung: Add support for SoC-specific suspend/resume callbacks
pinctrl: Don't override the error code in probe error handling
ARM: EXYNOS: Fix EINT wake-up mask configuration when pinctrl is used
pinctrl: exynos: Add support for set_irq_wake of wake-up EINTs
pinctrl: samsung: fix suspend/resume functionality
Here's a shorter set of fixes for 3.10, all for Samsung Exynos platforms.
It also includes a defconfig update so that exynos_defconfig provides
a meaningful set of drivers to boot an unmodified kernel on the Samsung
ARM-based Chromebooks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=TUvk
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Exynos fixes from Olof Johansson:
"Here's a shorter set of fixes for 3.10, all for Samsung Exynos
platforms.
It also includes a defconfig update so that exynos_defconfig provides
a meaningful set of drivers to boot an unmodified kernel on the
Samsung ARM-based Chromebooks."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: exynos: defconfig update
ARM: SAMSUNG: Add names to fimd0 IRQ resources
ARM: EXYNOS: fix software reset logic for EXYNOS5440 SOC
ARM: EXYNOS: Fix support of Exynos4210 rev0 SoC
ARM: dts: Enabling samsung-usb2phy driver for exynos5250
This turns on a number of configs that are useful on the Chromebook, but also
good to have on in general:
* USB host and MMC drivers(!)
* I2C GPIO arbitration driver
* CYAPA trackpad driver
* simplefb
* CROS EC and keyboard drivers
* S5M8767 driver
* MAX77686 drivers
* MAX8997 driver
* DEVTMPFS + mount
* DM_CRYPT (as module)
* CRYPTOLOOP
* HIGHMEM
* PRINTK timestamps
This also turns off DEBUG_LL, and switches the hardcoded Samsung lowlevel
uart to uart 3 (which is only used to show the "uncompressing kernel"
message at boot, it seems).
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
When adding CPU to the SMP group and enabling the coherency on this
CPU we must protect the register access.
The previous implementation claims to be atomic but doesn't provide
any protection against parallel access to the coherency fabric control
and configuration registers.
This patch fixes this by using the ldrex and strex mechanism.
This method should be used in all accesses to those registers.
[gregory.clement@free-electrons.com: fixed the commit's topic]
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When creating the DT based boards-ts219.c the none DT ts219-setup.c
was used as a template. This includes a lateinit() call to initialize
the PCIe bus. The code makes use of machine_is_ts219() which is never
true on DT, so a FIXME was added and the code left as is. This was
unproblematic until b73690c8f8b5d: "ARM: Kirkwood: Support basic
hotplug for PCI-E" which changes the way the PCIe bus is
initialized. The non-DT ts219-setup.c now crashes during boot. The
lateinit() call in the DT boards-ts219.c is being called,
machine_is_ts219() is true and so the PCIe is initialized a second
time.
This patch removes the useless, and now clearly dangerous, code from
boards-ts219.c, making ts219-setup.c work again.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.9.x
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- to get usb2 working on the Chromebook with adding the
usb phy node for usb2 on exynos5250
- supporting exynos4210 rev0 SoC
- exynos5440 restart applying only to powered-on domains
- drm-exynos probe failure with adding resource names to
fimd0 platform device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=+rdH
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim:
Fixes following for v3.10
- to get usb2 working on the Chromebook with adding the
usb phy node for usb2 on exynos5250
- supporting exynos4210 rev0 SoC
- exynos5440 restart applying only to powered-on domains
- drm-exynos probe failure with adding resource names to
fimd0 platform device
* tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Add names to fimd0 IRQ resources
ARM: EXYNOS: fix software reset logic for EXYNOS5440 SOC
ARM: EXYNOS: Fix support of Exynos4210 rev0 SoC
ARM: dts: Enabling samsung-usb2phy driver for exynos5250
On DT-enabled systems pinctrl-exynos driver is responsible for handling
of wake-up EINT interrupts. This patch adjusts wake-up mask
configuration code to take wake-up mask value from pinctrl-exynos driver
on DT-enabled systems.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes a bug introduced in the v3.10 merge window.
The AB8500 External Regulator driver has recently landed upstream,
which registers each of the 3 external regulators located on the
AB8500. If these regulators are marked as 'always on', there is a
potential for power-loss. If they're not and are seemingly unused
the Regulator subsystem will attempt to disable them to save power.
This causes an issue for AUX1, AUX2 and AUX3 as they obtain their
power from EXT3. So we're specifying that here to prevent EXT3 from
being powered down.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Multiplatform calls all enabled platforms' initcalls. In the
ux500_idle_init() initcall we call into the DBx500-PRCMU which in turn
executes some ux500 specific register reads/writes. When running on
some !ux500 platforms this ends up causing a kernel Oops. This patch
ensures the PRCMU call is only invoked when running on ux500 based
platforms.
Reported-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull ARM fixes from Russell King:
"Just three this time, all really quite small"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7729/1: vfp: ensure VFP_arch is non-zero when VFP is not supported
ARM: 7727/1: remove the .vm_mm value from gate_vma
ARM: 7723/1: crypto: sha1-armv4-large.S: fix SP handling
We didn't have any fixes sent up for -rc2, so this is a slightly larger
batch. A bit all over the place platform-wise; OMAP, at91, marvell,
renesas, sunxi, ux500, etc.
I tried to summarize highlights but there isn't a whole lot to point
out. Lots of little things fixed all over. A couple of defconfig updates
due to new/changing options.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8tMi
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We didn't have any fixes sent up for -rc2, so this is a slightly
larger batch. A bit all over the place platform-wise; OMAP, at91,
marvell, renesas, sunxi, ux500, etc.
I tried to summarize highlights but there isn't a whole lot to point
out. Lots of little things fixed all over. A couple of defconfig
updates due to new/changing options."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: at91/sama5: fix incorrect PMC pcr div definition
ARM: at91/dt: fix macb pinctrl_macb_rmii_mii_alt definition
ARM: at91: at91sam9n12: move external irq declatation to DT
ARM: shmobile: marzen: Use error values in usb_power_*
ARM: tegra: defconfig fixes
ARM: nomadik: fix IRQ assignment for SMC ethernet
ARM: vt8500: Add missing NULL terminator in dt_compat
clk: tegra: add ac97 controller clock
clk: tegra: remove USB from clk init table
ARM: dts: mvebu: Fix wrong the address reg value for the L2-cache node
ARM: plat-orion: Fix num_resources and id for ge10 and ge11
ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis
SERIAL: OMAP: Remove the slave idle handling from the driver
ARM: OMAP2+: serial: Remove the un-used slave idle hooks
ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes
ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active
ARM: OMAP2+: hwmod: Fix sidle programming in _enable_sysc()/_idle_sysc()
arm: mvebu: fix the 'ranges' property to handle PCIe
ARM: mvebu: select ARCH_REQUIRE_GPIOLIB for mvebu platform
ARM: AM33XX: Add missing .clkdm_name to clkdiv32k_ick clock
...
- Fix build breakage in pinctrl driver when no other architecture is selected
- Fix Mini X-plus device tree build
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n8M7
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-3.10' of git://github.com/mripard/linux into fixes
From Maxime Ripard:
Small set of fixes for 3.10:
- Fix build breakage in pinctrl driver when no other architecture is selected
- Fix Mini X-plus device tree build
* tag 'sunxi-fixes-for-3.10' of git://github.com/mripard/linux:
ARM: sunxi: select ARCH_REQUIRE_GPIOLIB
ARM: sunxi: Fix Mini X-plus device tree build
Signed-off-by: Olof Johansson <olof@lixom.net>
Since commit 1977e6d8 (drm/exynos: change the method for getting the
interrupt) the Exynos DRM FIMD driver requires IRQ resources to be
named. This patch fixes probe failure in non-DT cases by adding
appropriate resource names to fimd0 platform device.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes software reset logic. Software reset applies only to
powered-on domains in SOC because software reset to all domains causes
reboot failure.
Signed-off-by: Jungseok Lee <jays.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch extends exynos_init_time() function to handle Exynos4210
rev0 SoC, which differs in availability of system timers and needs
different clocksource initialization.
This makes it possible to use exynos_init_time() function as init_time
callback for all Exynos-based boards, including Universal_C210, which
originally had to use samsung_timer_init().
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
AT91 peripherals on SAMA5.
Two DT related fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRn4e+AAoJEAf03oE53VmQDTUH/ip4XID1+2KH1n64Dejl+TzO
m1RWz3Sesjv9MsndTeoZjXaBt24Bxn/u18XZv67rzf3nlGlGn29zmbux0zKncPSV
IWLZGoDorLO2URegNjDXD2Sk8/SLHqDaDzjDxnfuwfiSiE/qiCVTmvfGlkUNM/G5
qCu/k9jJ3NRyPFm9yzBqhLreWp9XKvXnVtHbOxjkqBz1AKSsfXa/iQc2Ekkb6k8/
YANAlG+MIZe/DWWtLT94XQkV15rorDgylQkQPfK+KDn6vUTKxm30BbcKXK2mxqir
NtbOXfQoheSATVs4fzIS3IW1Jo8WZXGBd5DOfXFiCI152q0d9RbvD5vsmqUnws8=
=3mcQ
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre:
- One definition fix that can lead to mis-clock some AT91 peripherals on SAMA5.
- Two DT related fixes.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/sama5: fix incorrect PMC pcr div definition
ARM: at91/dt: fix macb pinctrl_macb_rmii_mii_alt definition
ARM: at91: at91sam9n12: move external irq declatation to DT
Signed-off-by: Olof Johansson <olof@lixom.net>
The PA24 pin is wrongly assigned to peripheral B.
In the current config there is 2 ETX3 pins (PA11 and PA24) and
no ETXER pin (PA22).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> # 3.8+
The CSPI controller has only one clock, but the driver spi-imx.c needs
clock "per" to calculate bitrate divisor.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Here are a number of tiny USB bugfixes / new device ids for 3.10-rc2
The majority of these are USB gadget fixes, but they are all small.
Other than that, some USB host controller fixes, and USB serial driver
fixes for problems reported with them.
Also hopefully a fixed up USB_OTG Kconfig dependancy, that one seems to
be almost impossible to get right for all of the different platforms
these days.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlGeP/gACgkQMUfUDdst+ykXygCfeIL5/HMREhUSHQgb6IiIDR81
QHAAn0zJfRAyWUz4AtbrRsLSVfk3Q9vm
=DQIq
-----END PGP SIGNATURE-----
Merge tag 'usb-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of tiny USB bugfixes / new device ids for 3.10-rc2
The majority of these are USB gadget fixes, but they are all small.
Other than that, some USB host controller fixes, and USB serial driver
fixes for problems reported with them.
Also hopefully a fixed up USB_OTG Kconfig dependancy, that one seems
to be almost impossible to get right for all of the different
platforms these days."
* tag 'usb-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (56 commits)
USB: cxacru: potential underflow in cxacru_cm_get_array()
USB: ftdi_sio: Add support for Newport CONEX motor drivers
USB: option: add device IDs for Dell 5804 (Novatel E371) WWAN card
usb: ohci: fix goto wrong tag in err case
usb: isp1760-if: fix memleak when platform_get_resource fail
usb: ehci-s5p: fix memleak when fallback to pdata
USB: serial: clean up chars_in_buffer
USB: ti_usb_3410_5052: fix chars_in_buffer overhead
USB: io_ti: fix chars_in_buffer overhead
USB: ftdi_sio: fix chars_in_buffer overhead
USB: ftdi_sio: clean up get_modem_status
USB: serial: add generic wait_until_sent implementation
USB: serial: add wait_until_sent operation
USB: set device dma_mask without reference to global data
USB: Blacklisted Cinterion's PLxx WWAN Interface
usb: option: Add Telewell TW-LTE 4G
USB: EHCI: remove bogus #error
USB: reset resume quirk needed by a hub
USB: usb-stor: realtek_cr: Fix compile error
usb, chipidea: fix link error when USB_EHCI_HCD is a module
...
As pll5_video_div has been introduced to represent the clock
generated from post-divider for video.
Instead of pll5_video, pll5_video_div should be proper root clock
for ldb_di_sel.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Commit d3f79584a8 ("ARM: cleanup undefined instruction entry code")
improved the register scheduling when handling undefined instructions.
A side effect of this is that r5 is now used as a temporary, whilst the
VFP probing code relies on r5 containing a non-zero value when VFP is
not supported.
This patch fixes the VFP detection code so that we don't rely on the
contents of r5. Without this patch, Linux dies loudly on CPUs without
VFP support.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If one reads /proc/$PID/smaps, the mmap_sem belonging to the
address space of the task being examined is locked for reading.
All the pages of the vmas belonging to the task's address space
are then walked with this lock held.
If a gate_vma is present in the architecture, it too is examined
by the fs/proc/task_mmu.c code. As gate_vma doesn't belong to the
address space of the task though, its pages are not walked.
A recent cleanup (commit f6604efe) of the gate_vma initialisation
code set the vm_mm value to &init_mm. Unfortunately a non-NULL
vm_mm value in the gate_vma will cause the task_mmu code to attempt
to walk the pages of the gate_vma (with no mmap-sem lock held). If
one enables Transparent Huge Page support and vm debugging, this
will then cause OOPses as pmd_trans_huge_lock is called without
mmap_sem being locked.
This patch removes the .vm_mm value from gate_vma, restoring the
original behaviour of the task_mmu code.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make the SHA1 asm code ABI conformant by making sure all stack
accesses occur above the stack pointer.
Origin:
http://git.openssl.org/gitweb/?p=openssl.git;a=commit;h=1a9d60d2
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GyZI
-----END PGP SIGNATURE-----
Merge tag 'renesas-boards-marzen-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Correct USB PHY initialisation on the marzen board.
* tag 'renesas-boards-marzen-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: marzen: Use error values in usb_power_*
Signed-off-by: Olof Johansson <olof@lixom.net>
with DT.
Basic build, boot, and PM test logs are here - unfortunately, not for
the DT case yet:
http://www.pwsan.com/omap/testlogs/uart_idle_fix_v3.10-rc/20130519164010/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=DRuE
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-a-for-3.10-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley:
Fix the OMAP serial driver to work correctly on OMAP4 when booting
with DT.
* tag 'omap-fixes-a-for-3.10-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis
SERIAL: OMAP: Remove the slave idle handling from the driver
ARM: OMAP2+: serial: Remove the un-used slave idle hooks
ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes
ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active
ARM: OMAP2+: hwmod: Fix sidle programming in _enable_sysc()/_idle_sysc()
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch updates the marzen board code as if USB PHY isn't enabled
they phy will have a value set by ERR_PTR() rather than be NULL.
Without this patch a NULL pointer dereference and kernel panic
occurs on initialisation of USB on marzen.
This resolves a regression introduced in 3.10-rc1 by
b7fa5c2aec
("usb: phy: return -ENXIO when PHY layer isn't enabled").
Tested-by: Nguyen Hong Ky <nh-ky@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Before f7b861b7a6 ("arm: Use generic idle loop") ARM would kill the
CPU within the rcu idle section. Now that the rcu_idle_enter()/exit()
pair have been pushed lower down in the idle loop this is no longer true
and so using RCU_NONIDLE here is no longer necessary and also harmful
because RCU is not actually idle at this point.
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The AK8975 Kconfig option was renamed during the 3.10 merge window.
Adjust tegra_defconfig to enable the new name, so it's not missing
useful features.
Tegra DRM support used to be enabled in the default Tegra configuration,
but it now depends on CONFIG_TEGRA_HOST1X which is disabled by default.
Enable CONFIG_TEGRA_HOST1X so that DRM support is compiled in again.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
[swarren, squashed Alex's and my changes together]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The assignment of IRQ for the SMC91x ethernet adapter had two
problems making it non-working:
- It was not put into the ethernet device node. Let's do this
by using the board-specific overlay, so we can make other
overlays on other Nomadik boards.
- The IRQ number was actually completely wrong, this was the
number for NHK8815, not S8815.
After this ethernet starts working on the USB S8815.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fixes up the debug UART
- Fix dangerous platform data double-assignment
- Fix auxdata for the ethernet device
- Select REGULATOR to satisfy Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=uq56
-----END PGP SIGNATURE-----
Merge tag 'ux500-arm-soc-v3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij, some ux500 fixes for the v3.10-rc series:
- Fixes up the debug UART
- Fix dangerous platform data double-assignment
- Fix auxdata for the ethernet device
- Select REGULATOR to satisfy Kconfig
* tag 'ux500-arm-soc-v3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: select REGULATOR
ARM: ux500: Provide device enumeration number suffix for SMSC911x
ARM: ux500: Fix incorrect DEBUG UART virtual addresses
ARM: ux500: Remove duplicated assignment of ab8500_platdata
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson