Support for using UD and AF_IB is currently broken. The
IB_CM_SIDR_REQ_RECEIVED message is not handled properly in
cma_save_net_info() and we end up falling into code that will try and
process the request as ipv4/ipv6, which will end up failing.
The resolution is to add a check for the SIDR_REQ and call
cma_save_ib_info() with a NULL path record. Change cma_save_ib_info()
to copy the src sib info from the listen_id when the path record is NULL.
Reported-by: Hari Shankar <Hari.Shankar@netapp.com>
Signed-off-by: Matt Finlay <matt@mellanox.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Problem reported by: Ted Kim <ted.h.kim@oracle.com>:
We have a case where a Linux system and a non-Linux system are
trying to interoperate. The Linux host is the active side and
starts the connection establishment, but later decides to not go
through with the connection setup and does rdma_destroy_id().
The rdma_destroy_id() eventually works its way down to cm_destroy_id()
in core/cm.c, where a REJ is sent. The non-Linux system
has some trouble recognizing the REJ because of:
A. CM states which can't receive the REJ
B. Some issues about REJ formatting (missing comm ID)
ISSUE A: That part of the spec says, a Consumer Reject REJ can be
sent for a connection abort, but it goes further
and says: can send a REJ message with a "Consumer Reject"
Reason code if they are in a CM state (i.e. REP
Rcvd, MRA(REP) Sent, REQ Rcvd, MRA Sent) that allows
a REJ to be sent (lines 35-38).
Of the states listed there in that sentence, it would
seem to limit the active side to using the Consumer Reject
(for the abort case) in just the REP-Rcvd and MRA-REP-Sent
states. That is basically only after the active side
sees a REP (or alternatively goes down the state transitions
to timeout in which case a Timeout REJ is sent).
As a fix, in cm-destroy-id() move the IB-CM-MRA-REQ-RCVD case
to the same as REQ-SENT. Essentially, make a REJ sent after
getting an MRA on active side a timeout rather than Consumer-
Reject, which is arguably more correct with the CM state
diagrams previous to getting a REP.
Signed-off-by: Ted Kim <ted.h.kim@oracle.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
HW currently restricts the IB MTU range between 512 and 4096.
Fail connection for MTUs lesser than 512.
Signed-off-by: Naga Irrinki <naga.irrinki@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
rdma_addr_find_dmac_by_grh fails to resolve dmac for link local address.
Use rdma_get_ll_mac to resolve the link local address.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Mitesh Ahuja <mitesh.ahuja@avagotech.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If DPP PDs are not supported by the FW, allocate only normal PDs.
Signed-off-by: Mitesh Ahuja <mitesh.ahuja@avagotech.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the adapter ports are in PFC mode and VLAN is not configured,
use vlan tag 0 for RoCE traffic. Also, log an advisory message
in system logs.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Don't move QP to error state, if QP is in reset state during QP
destroy operation.
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Changing the destroy sequence of mailbox queue and event queues.
FW expects mailbox queue to be destroyed before desroying the EQs.
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
These KERN_<LEVEL> uses are unnecessary with pr_<level> and cause
bad logging output so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Commit d4988623cc ("IB/qib: use arch_phys_wc_add()")
adjusted mtrr inititialization to use the new interface.
Unfortunately, the new interface returns a signed
value and the patch tested the unsigned wc_cookie.
Fix the issue by changing the type of wc_cookie to int. For
the success case the ret left at zero to avoid
a warning from the caller. For failure wc_cookie
is used as the ret.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The string iwpm_ulib_name is recorded in a nlmsg as a netlink attribute.
Without this fix parsing of the nlmsg by the userspace port mapper service fails
because of unknown attribute length, causing the port mapper service not to
register the client, which has sent the nlmsg.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Cc: <stable@vger.kernel.org> #v3.16
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For listening endpoints bound to the wildcard address, we need to pass
the wildcard address mapping to iwpm_get_remote_info() instead of the
mapped address of the new child connection.
Without this fix, and with iwarp port mapping enabled, each iw_cxgb4
connection that is spawned from a listening endpoint bound to the wildcard
address, will generate an annoying dmesg entry about failing to find
the remote address mapping info, and the connection state displayed in
debugfs under /sys/kernel/debug/iw_cxgb4/<pci-slot-no>/eps will not have
the peer's address/port mapping info. The connection still works though.
Fixes: 5b6b8fe ("RDMA/cxgb4: Report the actual address of the remote connecting peer")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Using an element of a struct as the address for the memcpy of the whole
struct may introduce a buffer overflow and does not help readability either
simply pass the real thing as first argument to memcpy.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
See also patch "IPoIB/cm: Add connected mode support for devices
without SRQs" (commit ID 68e995a295). Detected by smatch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove these log messages in favor of per-endpoint counters as well as
device-global counters that can be inspected via debugfs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Addresses the following kernel logs seen during boot of sparc systems:
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Kernel unaligned access at TPC[103bce50] cm_find_listen+0x34/0xf8 [ib_cm]
Signed-off-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This driver already makes use of ioremap_wc() on PIO buffers,
so convert it to use arch_phys_wc_add().
The qib driver uses a mmap() special case for when PAT is
not used, this behaviour used to be determined with a
module parameter but since we have been asked to just
remove that module parameter this checks for the WC cookie,
if not set we can assume PAT was used. If its set we do
what we used to do for the mmap for when MTRR was enabled.
The removal of the module parameter is OK given that Andy
notes that even if users of module parameter are still around
it will not prevent loading of the module on recent kernels.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Stefan Bader <stefan.bader@canonical.com>
Cc: konrad.wilk@oracle.com
Cc: ville.syrjala@linux.intel.com
Cc: david.vrabel@citrix.com
Cc: jbeulich@suse.com
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: infinipath@intel.com
Cc: linux-rdma@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xensource.com
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is no good reason not to, we eventually delete it as well.
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Juergen Gross <jgross@suse.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Mike Marciniszyn <infinipath@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
While unmapping an ODP writable page, the dirty bit of the page is set. In
order to do so, the head of the compound page is found.
Currently, the compound head is found even on non-writable pages, where it is
never used, leading to unnecessary cpu barrier that impacts performance.
This patch moves the search for the compound head to be done only when needed.
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Acked-by: Shachar Raindel <raindel@mellanox.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently, while mapping or unmapping pages for ODP, the umem mutex is locked
and unlocked once for each page. Such lock/unlock operation take few tens to
hundreds of nsecs. This makes a significant impact when mapping or unmapping few
MBs of memory.
To avoid this, the mutex should be locked only once per operation, and not per
page.
Signed-off-by: Guy Shapiro <guysh@mellanox.com>
Acked-by: Shachar Raindel <raindel@mellanox.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Get the actual (non-mapped) ip/tcp address of the connecting peer from
the port mapper
Also setup the passive side endpoint to correctly display the actual
and mapped addresses for the new connection.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Get the actual (non-mapped) ip/tcp address of the connecting peer from
the port mapper and report the address info to the user space application
at the time of connection establishment
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add functionality to enable the port mapper on the passive side to provide to its
clients the actual (non-mapped) ip/tcp address information of the connecting peer
1) Adding remote_info_cb() to process the address info of the connecting peer
The address info is provided by the user space port mapper service when
the connection is initiated by the peer
2) Adding a hash list to store the remote address info
3) Adding functionality to add/remove the remote address info
After the info has been provided to the port mapper client,
it is removed from the hash list
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently the iw_cxgb4 implementation requires the qp and cq qid densities
to match as well as the qp and cq id ranges. So fail a device open if
the device configuration doesn't meet the requirements.
The reason for these restictions has to do with the fact that IQ qid X
has a UGTS register in the same bar2 page as EQ qid X. Thus both qids
need to be allocated to the same user process for security reasons.
The logic that does this (the qpid allocator in iw_cxgb4/resource.c)
handles this but requires the above restrictions.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For T5, we must not use the kdb/kgts registers, in order avoid db drops
under extreme loads.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
- get_dma_mr() was using ~0UL which is should be ~0ULL. This causes the
DMA MR to get setup incorrectly in hardware.
- wr_log_show() needed a 64b divide function div64_u64() instead of
doing
division directly.
- fixed warnings about recasting a pointer to a u64
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When accepting a new IPv4 connect to an IPv6 socket, the CMA tries to
canonize the address family to IPv4, but does not properly process
the listening sockaddr to get the listening port, and does not properly
set the address family of the canonized sockaddr.
Fixes: e51060f08a ("IB: IP address based RDMA connection manager")
Cc: <stable@vger.kernel.org>
Reported-By: Yotam Kenneth <yotamke@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity in target land the last months.
The highlights include:
- Convert fabric drivers tree-wide to target_register_template() (hch
+ bart)
- iser-target hardening fixes + v1.0 improvements (sagi)
- Convert iscsi_thread_set usage to kthread.h + kill
iscsi_target_tq.c (sagi + nab)
- Add support for T10-PI WRITE_STRIP + READ_INSERT operation (mkp +
sagi + nab)
- DIF fixes for CONFIG_DEBUG_SG=y + UNMAP file emulation (akinobu +
sagi + mkp)
- Extended TCMU ABI v2 for future BIDI + DIF support (andy + ilias)
- Fix COMPARE_AND_WRITE handling for NO_ALLLOC drivers (hch + nab)
Thanks to everyone who contributed this round with new features,
bug-reports, fixes, cleanups and improvements.
Looking forward, it's currently shaping up to be a busy v4.2 as well"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (69 commits)
target: Put TCMU under a new config option
target: Version 2 of TCMU ABI
target: fix tcm_mod_builder.py
target/file: Fix UNMAP with DIF protection support
target/file: Fix SG table for prot_buf initialization
target/file: Fix BUG() when CONFIG_DEBUG_SG=y and DIF protection enabled
target: Make core_tmr_abort_task() skip TMFs
target/sbc: Update sbc_dif_generate pr_debug output
target/sbc: Make internal DIF emulation honor ->prot_checks
target/sbc: Return INVALID_CDB_FIELD if DIF + sess_prot_type disabled
target: Ensure sess_prot_type is saved across session restart
target/rd: Don't pass incomplete scatterlist entries to sbc_dif_verify_*
target: Remove the unused flag SCF_ACK_KREF
target: Fix two sparse warnings
target: Fix COMPARE_AND_WRITE with SG_TO_MEM_NOALLOC handling
target: simplify the target template registration API
target: simplify target_xcopy_init_pt_lun
target: remove the unused SCF_CMD_XCOPY_PASSTHROUGH flag
target/rd: reduce code duplication in rd_execute_rw()
tcm_loop: fixup tpgt string to integer conversion
...
Pull networking fixes from David Miller:
1) Fix verifier memory corruption and other bugs in BPF layer, from
Alexei Starovoitov.
2) Add a conservative fix for doing BPF properly in the BPF classifier
of the packet scheduler on ingress. Also from Alexei.
3) The SKB scrubber should not clear out the packet MARK and security
label, from Herbert Xu.
4) Fix oops on rmmod in stmmac driver, from Bryan O'Donoghue.
5) Pause handling is not correct in the stmmac driver because it
doesn't take into consideration the RX and TX fifo sizes. From
Vince Bridgers.
6) Failure path missing unlock in FOU driver, from Wang Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
net: dsa: use DEVICE_ATTR_RW to declare temp1_max
netns: remove BUG_ONs from net_generic()
IB/ipoib: Fix ndo_get_iflink
sfc: Fix memcpy() with const destination compiler warning.
altera tse: Fix network-delays and -retransmissions after high throughput.
net: remove unused 'dev' argument from netif_needs_gso()
act_mirred: Fix bogus header when redirecting from VLAN
inet_diag: fix access to tcp cc information
tcp: tcp_get_info() should fetch socket fields once
net: dsa: mv88e6xxx: Add missing initialization in mv88e6xxx_set_port_state()
skbuff: Do not scrub skb mark within the same name space
Revert "net: Reset secmark when scrubbing packet"
bpf: fix two bugs in verification logic when accessing 'ctx' pointer
bpf: fix bpf helpers to use skb->mac_header relative offsets
stmmac: Configure Flow Control to work correctly based on rxfifo size
stmmac: Enable unicast pause frame detect in GMAC Register 6
stmmac: Read tx-fifo-depth and rx-fifo-depth from the devicetree
stmmac: Add defines and documentation for enabling flow control
stmmac: Add properties for transmit and receive fifo sizes
stmmac: fix oops on rmmod after assigning ip addr
...
Currently, iflink of the parent interface was always accessed, even
when interface didn't have a parent and hence we crashed there.
Handle the interface types properly: for a child interface, return
the ifindex of the parent, for parent interface, return its ifindex.
For child devices, make sure to set the parent pointer prior to
invoking register_netdevice(), this allows the new ndo to be called
by the stack immediately after the child device is registered.
Fixes: 5aa7add8f1 ('infiniband/ipoib: implement ndo_get_iflink')
Reported-by: Honggang Li <honli@redhat.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Honggang Li <honli@redhat.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>+
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
set_filter_wr is requesting __GFP_NOFAIL allocation although it can return
ENOMEM without any problems obviously (t4_l2t_set_switching does that
already). So the non-failing requirement is too strong without any
obvious reason. Drop __GFP_NOFAIL and reorganize the code to have the
failure paths easier.
The same applies to _c4iw_write_mem_dma_aligned which uses __GFP_NOFAIL
and then checks the return value and returns -ENOMEM on failure. This
doesn't make any sense what so ever. Either the allocation cannot fail or
it can.
del_filter_wr seems to be safe as well because the filter entry is not
marked as pending and the return value is propagated up the stack up to
c4iw_destroy_listen.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some rare cases, IO operations may be not aligned to page
boundaries. This prevents iser from performing fast memory
registration. In order to overcome that iser uses a bounce
buffer to carry the transaction. We basically allocate a buffer
in the size of the transaction and perform a copy.
The buffer allocation using kmalloc is too restrictive since it
requires higher order (atomic) allocations for large transactions
(which may result in memory exhaustion fairly fast for some workloads).
We rewrite the bounce buffer code path to allocate scattered pages
and perform a copy between the transaction sg and the bounce sg.
Reported-by: Alex Lyakas <alex@zadarastorage.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In singleton scatterlists, DMA memory registration code
is taken both for Fastreg and FMR code paths. Move it to
a function.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead of passing ib_sge as output variable, we pass the mem_reg
pointer to have the routines fill the rkey as well. This reduces
code duplication and extra assignments. This is a preparation step
to unify some registration logics together. Also, pass iser_fast_reg_mr
the fastreg descriptor directly.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
No need to keep lkey, va, len variables, we can keep
them as struct ib_sge. This will help when we change the
memory registration logic.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Memory regions are resources that are saved
in the device caches. Increase the probability for
a cache hit by adding the MRU descriptor to pool
head.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Make iser_[create|destroy]_fastreg_desc shorter, more
readable and easily extendable.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead of open-coding connection fastreg pool get/put,
we introduce iser_reg_desc[get|put] helpers.
We aren't setting these static as this will be a per-device
routine later on. Also, cleanup iser_unreg_rdma_mem_fastreg
a bit.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
No need for these two separate. Keep it in a single routine
like in the fastreg case. This will also make iser_reg_page_vec
closer to iser_fast_reg_mr arguments. This is a preparation
step for registration flow refactor.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This struct members other than struct iser_mem_reg are unused,
so remove it altogether.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Buffer length was assigned twice, and no reason to set va to
io_addr and then add the offset, just set va to io_addr + offset.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Matthew Finlay