Details:
1. Unload all modules on fw_list of dsp when suspend, and reload all
modules on fw_list when resume.
2. A DSP expects only one scratch, but hsw_parse_fw_image() allocates
scratch blocks for each firmware image it parses. Move the allocate function
sst_block_alloc_scratch() out of hsw_parse_fw_image() to make sure a scratch
be allocated only after all firmware images be parsed.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The manual recommends that we reset the DSP when we suspend so add that in
runtime suspend handler
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IPC driver saved only IMR register, we need to save the CSR as well, so
add it
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The updated firmware expects the MMX ID to be used as 3, so update the
driver as well
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add SNDRV_PCM_INFO_DRAIN_TRIGGER in snd_pcm_hardware.info to
call sst_hsw_stream_set_silence_start() when PCM draining.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ADSP on Braswell/Baytrail is an ACPI device. This patch sets its initial
runtime PM status to active. Otherwise, its initial status is suspended and
runtime_suspend ops will not be called after probe and thus cannot further
trigger ACPI _PS3 (D3) method to put the device into low power D3cold state.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The BDW audio firmware DSP manages the DMA and the DMA cannot be
stopped exactly at the end of the playback stream. This means
stale samples may be played at PCM stop unless the driver copies
silence to the subsequent periods.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Nothing too exciting here yet, a small optimization for DAPM from
Lars-Peter and a few small bits and pieces for drivers but nothing
that really stands out.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUoX40AAoJECTWi3JdVIfQCHkH/20AXx65DLEvKjtKJTbhE25j
XSmN3ZtXuEdzg70rG1E2YZsZofxRWShX7HHyCwmepWfe30o+V4UCR+4HyHIWVLF6
O3TpupfcQ9ACP+/jQQxxySnTld6LJqW7rNXpxTVGeaba82uDtKIVgv/gHoUtEBDi
NfG0RoVcfpb0k52LWzijIDx4YxVCuIkPHLFqBP63S92XNgw7bc8zjMl65ayY43M+
obfD0ISIdEudmkyqNrQzuNtxl14wsYjzQ5VYqltW5kLaEQVtmD8Zp1bOVI3m0xhX
KY8zQnUUwA4+Cxs8aAm/NvczAZ/GyEQSIjTdUQZDXm0k6H81eya108SfxGvaMYI=
=DSaV
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.19-rc2' into asoc-linus
ASoC: Updates for v3.20
Nothing too exciting here yet, a small optimization for DAPM from
Lars-Peter and a few small bits and pieces for drivers but nothing
that really stands out.
# gpg: Signature made Tue 30 Dec 2014 00:15:48 HKT using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: key AF88CD16: no public key for trusted key - skipped
# gpg: key AF88CD16 marked as ultimately trusted
# gpg: key 5621E907: no public key for trusted key - skipped
# gpg: key 5621E907 marked as ultimately trusted
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
sound/soc/intel/cht_bsw_rt5645.c:315:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Removes some functions that are not used anywhere:
sst_hsw_stream_unmute() sst_hsw_stream_mute() msg_set_stage_type()
sst_hsw_dx_get_state() sst_hsw_stream_set_write_position()
sst_hsw_stream_get_vol_reg() sst_hsw_stream_get_peak_reg()
sst_hsw_stream_get_pointer_reg() sst_hsw_stream_get_read_reg()
sst_hsw_stream_get_mixer_id() sst_hsw_stream_get_hw_id()
sst_hsw_mixer_set_volume_curve() sst_hsw_mixer_unmute()
sst_hsw_mixer_mute() sst_hsw_stream_set_volume_curve()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Function sst_acpi_probe() uses plain strcpy for setting member firmware_name
of a struct intel_sst_drv from member firmware of a struct sst_machines.
Thereby the destination array has got a length of 20 byte while the source may
hold 32 byte. Since eg. commit 64b9c90b86 ("ASoC: Intel: Fix BYTCR firmware
name") increased strings from "fw_sst_0f28.bin" to "intel/fw_sst_0f28.bin"
there is an actual possibility that the 20 byte array at the end of struct
intel_sst_drv is overrun.
Thus increase the size of the destination and use the same define for both
structs. Detected by Coverity CID 1260087.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
All sst firmware is provided under the intel directory of the linux-firmware
tree. By default this directory structure is kept when installing on a target
system. Change the path to expect a default linux-firmware installation.
Signed-off-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All sst firmware is provided under the intel directory of the linux-firmware
tree. By default this directory structure is kept when installing on a target
system. Change the path to expect a default linux-firmware installation.
Signed-off-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add machine driver for two Intel Cherryview-based platforms, Cherrytrail
and Braswell, with RT5645 codec
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For runtime suspend/resume, it is some different with suspend/resume,
e.g. codec power supply won't be switch off, codec jack detection
still working(to wake up system from Jack event), won't call call
snd_soc_suspend/resume, etc.
So here, we add a platform PM status, HSW_PM_STATE_RTD3, to make
the status more clear, when in idle, it will enter this status, to
transfer from HSW_PM_STATE_RTD3 to HSW_PM_STATE_D3, we will do those
extra jobs, and vice versa for resuming.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reported by Coverity: CID 1267985 CID 1267986
Fix these two Defects: Uninitialized scalar variable.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added entry in sst driver to support rt5645 codec
for intel Braswell platform.
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We never set the ->scratch pointer, so let's delete it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need hold lock each time updating shirm registers, otherwise,
we may set unexpected values to them when they are set in
different thread at different time sequence.
The notification work will be scheduled in global work queue,
which won't hold this sst->spinlock itself, so here we need
change to use the lock version to update shim registers.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stream_hw_id for System stream is 0x0, if we use initial stream_hw_id
value 0, it may return wrong(not committed) stream when calling function
get_stream_by_id() with stream_id=0. Here initial stream_hw_id to invalid
value to fix this issue.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There may be 2 pcm streams for a same DAI at most, and these 2
streams should have different hsw_pcm_data, e.g. they have
different persistent data, so here we need split hsw_pcm_data
for playback and capture, to make sure they won't be mixed
and keep cleaned.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A DAI may have 2 streams(playback/capture) and different modules
may be needed for them respectively, so we need add a stream
direction here, the combination(dai_id + stream) can tell us
which module we really need here.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The first 512 bytes of data DRAM memory is used for FW dump,
and this first data SRAM block should be never power gated
(always on), here always enable the block(DSRAM[0]) for D0
stage.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Cherrytrail and Braswell, the I2S BCLK is 100FS which cannot be supported
by RT5672 in slave mode and can cause noise. This patch selects codec ASRC
clock source to track I2S1 clock so that codec ASRC can be enabled to suppress
the noise.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should not send IPC stream commands to FW when the stream is
NULL, dereference the NULL pointer may also occur without precheck.
Here add NULL pointer checks for these stream APIs.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ALSA core takes care that all preallocated memory is freed when the PCM
itself is freed. There is no need to do this manually in the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Board level DAPM elements should be registered with the card's DAPM context
rather than the CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To work properly snd_soc_dapm_ignore_suspend() needs to be called on
endpoint widgets. In this case those are the board level Speaker and
Headphone widgets and not the CODEC output widgets that are connected to
them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DAPM widgets are enabled by default, there is no need to enable them unless
they have previously been explicitly disabled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The offset of block allocator, ba->offset, should not be changed during
fixed address allocating, for the caller may treat it as the offset of
allocated memory and use it. In the case that we allocate more than 1
blocks, we should make sure this offset is correct.
Here introduces a temp allocator for the later continuous allocating.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The release_firmware() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The sst_dma_free() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
To enable some modules from other than base FW, according
to FW interface spec, we need pass the correct entry point
param to FW, so here store the entry_point read from FW
file for later usage.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For block span more than 1 section, when allocate it from
a free block, we need allocate the remain buffers within
the block, and then continue alloc the rest of needed
size buffer.
Here also make sure this free block is moved from free
list to used list, and add it to block_list which may
be used for power gating disabling later.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings:
sound/soc/intel/sst/sst_acpi.c:248:5: warning:
symbol 'sst_acpi_probe' was not declared. Should it be static?
sound/soc/intel/sst/sst_acpi.c:335:5: warning:
symbol 'sst_acpi_remove' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_sst_bytcr_dpcm_rt5640 doesn't autoload because MODULE_ALIAS doesn't
match with "bytt100_rt5640" platform device.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BYTCR DSP firmware is in intel/ subdirectory. See linux-firmware.git
commit d562a3b63632 ("linux-firmware: add sst audio firmware for baytrail
platforms").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The line continuation in Kconfig should be a '\' instead of '\\'.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix following build error when CONFIG_I2C is not enabled:
sound/soc/codecs/rt5640.c:2252:1: warning: data definition has no type or storage class
module_i2c_driver(rt5640_i2c_driver);
^
sound/soc/codecs/rt5640.c:2252:1: error: type defaults to ‘int’ in declaration of ‘module_i2c_driver’ [-Werror=implicit-int]
sound/soc/codecs/rt5640.c:2252:1: warning: parameter names (without types) in function declaration
sound/soc/codecs/rt5640.c:2241:26: warning: ‘rt5640_i2c_driver’ defined but not used [-Wunused-variable]
static struct i2c_driver rt5640_i2c_driver = {
^
cc1: some warnings being treated as errors
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/intel/bytcr_dpcm_rt5640.c:218:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/intel/cht_bsw_rt5672.c:273:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This removes the last few uses of CONFIG_PM_RUNTIME introduced
recently and makes that config option finally go away.
CONFIG_PM will be available directly from the menu now and
also it will be selected automatically if CONFIG_SUSPEND or
CONFIG_HIBERNATION is set.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=QnSO
-----END PGP SIGNATURE-----
Merge tag 'pm-config-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CONFIG_PM_RUNTIME elimination from Rafael Wysocki:
"This removes the last few uses of CONFIG_PM_RUNTIME introduced
recently and makes that config option finally go away.
CONFIG_PM will be available directly from the menu now and also it
will be selected automatically if CONFIG_SUSPEND or CONFIG_HIBERNATION
is set"
* tag 'pm-config-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Eliminate CONFIG_PM_RUNTIME
tty: 8250_omap: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound: sst-haswell-pcm: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
Here are a few fixes that have landed after the previous pull
request. All are driver specific fixes including:
- error/int value fixes in OXFW,
- Intel Skylake HD-audio HDMI codec support,
- Additional HD-audio Realtek codecs and AD1986A codec fixes/quirks,
- a few more DSD support and a quirk for Arcam rPAC in usb-audio,
- a typo fix for Scarlett 6i6,
- fixes for new ASIHPI firmware,
- ASoC Exynos7 cleanups,
- Intel ACPI support, and
- a fix for PCM512 register cache sync.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=HRbM
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a few fixes that have landed after the previous pull request.
All are driver specific fixes including:
- error/int value fixes in OXFW,
- Intel Skylake HD-audio HDMI codec support,
- Additional HD-audio Realtek codecs and AD1986A codec fixes/quirks,
- a few more DSD support and a quirk for Arcam rPAC in usb-audio,
- a typo fix for Scarlett 6i6,
- fixes for new ASIHPI firmware,
- ASoC Exynos7 cleanups,
- Intel ACPI support, and
- a fix for PCM512 register cache sync"
* tag 'sound-fix-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
ALSA: usb-audio: extend KEF X300A FU 10 tweak to Arcam rPAC
ALSA: hda/realtek - New codec support for ALC298
ALSA: asihpi: update to HPI version 4.14
ALSA: asihpi: increase tuner pad cache size
ALSA: asihpi: relax firmware version check
ALSA: usb-audio: Fix Scarlett 6i6 initialization typo
ALSA: hda - Add quirk for Packard Bell EasyNote MX65
ALSA: usb-audio: add native DSD support for Matrix Audio DACs
ALSA: hda/realtek - New codec support for ALC256
ALSA: hda/realtek - Add new Dell desktop for ALC3234 headset mode
ASoC: Intel: fix possible acpi enumeration panic
ALSA: hda/hdmi - apply Haswell fix-ups to Skylake display codec
ASoC: Intel: fix return value check in sst_acpi_probe()
ALSA: hda - Make add_stereo_mix_input flag tristate
ALSA: hda - Create capture source ctls when stereo mix input is added
ALSA: hda - Fix typos in snd_hda_get_int_hint() kerneldoc comments
ALSA: hda - add codec ID for Skylake display audio codec
ALSA: oxfw: some signedness bugs
ALSA: oxfw: fix detect_loud_models() return value
ASoC: rt5677: add REGMAP_I2C and REGMAP_IRQ dependency
...
Mark Brown