The current logic in cifs_setattr calls mode_to_acl twice on mode
changes if cifsacl is enabled. Remove the duplicate call.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
CC: Shirish Pargaonkar <shirishp@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Use creation by full path instead: "fs/foo".
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
treeName part is canonicalized to '/' path separator
Signed-off-by: Igor Mammedov <niallain@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
The transport encryption capability and new SetFSInfo level were missing, and the
new proxy capability (which Samba server is implementing) and proxy setfsinfo needed
to be moved down to not collide with Samba's transport encryption capability.
CC: Jeremy Allison <jra@samba.org>
CC: Sam Liddicott <sam@lidicott.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
When a share was in DFS and the server was Unix/Linux, we were sending paths of the form
\\server\share/dir/file
rather than
//server/share/dir/file
There was some discussion between me and jra over whether we should use
/server/share/dir/file
as MS sometimes says - but the documentation for this claims it should be
doubleslash for this type of UNC-like path format and that works, so leaving
it as doubleslash but converting the \ to / in the the //server/share portion.
This gets Samba to now correctly return STATUS_PATH_NOT_COVERED when it is
supposed to (Windows already did since the direction of the slash was not an issue
for them). Still need another minor change to fully enable DFS (need to finish
some chages to SMBGetDFSRefer
Signed-off-by: Steve French <sfrench@us.ibm.com>
New WAFS filer uses ioctls which are shown to be available
on a share by querying this info level
Acked-by: Sam Liddicott <sam@liddicott.com>
Signed-off-by: Stevef French <sfrench@us.ibm.com>
This patch makes the needlessly global cifs_dfs_automount_list static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
If a tcon is being freed in call tconInfoFree, clean up any entries that may
exist in global oplock queue as the tcon structure hanging off of those entries
will be invalid and can cause oops while accesing any elements in the
tcon structure.
Signed-off-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
... and take it out of ->umount_begin() instances. Call with all locks
already taken (by do_umount()) and leave calling release_mounts() to
caller (it will do release_mounts() anyway, so we can just put into
the same list).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Shirish Pargaonkar noted:
With cifsacl mount option, when a file is created on the Windows server,
exclusive oplock is broken right away because the get cifs acl code
again opens the file to obtain security descriptor.
The client does not have the newly created file handle or inode in any
of its lists yet so it does not respond to oplock break and server waits for
its duration and then responds to the second open. This slows down file
creation signficantly. The fix is to pass the file descriptor to the get
cifsacl code wherever available so that get cifs acl code does not send
second open (NT Create ANDX) and oplock is not broken.
CC: Shirish Pargaonkar <shirishp@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Kukks noticed that cp -p can write out file data too late, after the timestamp
is already set. This was introduced as an unintentional sideeffect of the change
in an earlier patch (see below) which fixed some delayed return code propagation.
cea218054a
Author: Jeff Layton <jlayton@redhat.com>
Date: Tue Nov 20 23:19:03 2007 +0000
Acked-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Jeff Layton that we were converting \ to / in the posix path case which is
not always right (depends on what the old delim was).
CC: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
* Add path_put() functions for releasing a reference to the dentry and
vfsmount of a struct path in the right order
* Switch from path_release(nd) to path_put(&nd->path)
* Rename dput_path() to path_put_conditional()
[akpm@linux-foundation.org: fix cifs]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: <linux-fsdevel@vger.kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the central patch of a cleanup series. In most cases there is no good
reason why someone would want to use a dentry for itself. This series reflects
that fact and embeds a struct path into nameidata.
Together with the other patches of this series
- it enforced the correct order of getting/releasing the reference count on
<dentry,vfsmount> pairs
- it prepares the VFS for stacking support since it is essential to have a
struct path in every place where the stack can be traversed
- it reduces the overall code size:
without patch series:
text data bss dec hex filename
5321639 858418 715768 6895825 6938d1 vmlinux
with patch series:
text data bss dec hex filename
5320026 858418 715768 6894212 693284 vmlinux
This patch:
Switch from nd->{dentry,mnt} to nd->path.{dentry,mnt} everywhere.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix cifs]
[akpm@linux-foundation.org: fix smack]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, when we get a prefixpath as part of mount, the kernel only
changes the first character to be a '/' or '\' depending on whether
posix extensions are enabled. This is problematic as it expects
mount.cifs to pass in the correct delimiter in the rest of the
prefixpath. But, mount.cifs may not know *what* the correct delimiter
is. It's a chicken and egg problem.
Note that mount.cifs should not do conversion of the
prefixpath - if we want posix behavior then '\' is legal in a path
(and we have had bugs in the distant path to prove to me that
customers sometimes have apps that require '\'). The kernel code
assumes that the path passed in is posix (and current code will handle
the first path component fine but was broken for Windows mounts
for "deep" prefixpaths unless the user specified a prefixpath with '\'
deep in it. So e.g. with current kernel code:
1) mount to //server/share/dir1 will work to all server types
2) mount to //server/share/dir1/subdir1 will work to Samba
3) mount to //server/share/dir1\\subdir1 will work to Windows
But case two would fail to Windows without the fix.
With the kernel cifs module fix case two now works.
First analyzed by Jeff Layton and Simo Sorce
CC: Jeff Layton <jlayton@redhat.com>
CC: Simo Sorce <simo@samba.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This patch fixes an error in the experimental cifs acl code. During chmod,
set security descriptor data (num aces) is not sent with little-endian encoding.
Signed-off-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Although these experimental operations are not fully implemented, fix the
typo in the definition of the quotactl operations for cifs.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Christoph had noticed too many ifdefs in the CIFS code making it
hard to read. This patch removes about a quarter of them from
the C files in cifs by improving a few key ifdefs in the .h files.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Stop the CIFS filesystem from using iget() and read_inode(). Replace
cifs_read_inode() with cifs_iget(), and call that instead of iget().
cifs_iget() then uses iget_locked() directly and returns a proper error code
instead of an inode in the event of an error.
cifs_read_super() now returns any error incurred when getting the root inode
instead of ENOMEM.
cifs_iget() needs examining. The comment "can not call macro FreeXid here
since in a void func" is no longer true.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Steven French <sfrench@us.ibm.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplify page cache zeroing of segments of pages through 3 functions
zero_user_segments(page, start1, end1, start2, end2)
Zeros two segments of the page. It takes the position where to
start and end the zeroing which avoids length calculations and
makes code clearer.
zero_user_segment(page, start, end)
Same for a single segment.
zero_user(page, start, length)
Length variant for the case where we know the length.
We remove the zero_user_page macro. Issues:
1. Its a macro. Inline functions are preferable.
2. The KM_USER0 macro is only defined for HIGHMEM.
Having to treat this special case everywhere makes the
code needlessly complex. The parameter for zeroing is always
KM_USER0 except in one single case that we open code.
Avoiding KM_USER0 makes a lot of code not having to be dealing
with the special casing for HIGHMEM anymore. Dealing with
kmap is only necessary for HIGHMEM configurations. In those
configurations we use KM_USER0 like we do for a series of other
functions defined in highmem.h.
Since KM_USER0 is depends on HIGHMEM the existing zero_user_page
function could not be a macro. zero_user_* functions introduced
here can be be inline because that constant is not used when these
functions are called.
Also extract the flushing of the caches to be outside of the kmap.
[akpm@linux-foundation.org: fix nfs and ntfs build]
[akpm@linux-foundation.org: fix ntfs build some more]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: David Chinner <dgc@sgi.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andi Kleen noticed that we were logging access denied errors (which is
noisy in the dmesg log, and not needed to be logged) and that we were
logging path names on that an other errors (e.g. EIO) which we should
not be doing.
CC: Andi Kleen <ak@suse.de>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Also cifs_fs_type was made not static for ussage in dfs code.
Signed-off-by: Igor Mammedov <niallain@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Adds additional option CIFS_DFS_UPCALL to fs/Kconfig for enabling
DFS support. Resolved IP address is saved as a string in the
key payload.
Igor has a series of related patches that will follow which finish up
CIFS DFS support
Acked-by: Igor Mammedov <niallain@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Requires cifsacl mount flag to be on and CIFS_EXPERIMENTAL enabled
CC: Shirish Pargaonkar <shirishp@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Unicode strings need to be word aligned, but the code that handles that
is currently not taking the length of the SPNEGO blob into account. Fix
it to do so.
Signed-off-by: Jeff Layton <jlayton@tupile.poochiereds.net>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Currently, any new kerberos SMB session overwrites the server's session
key. The session key should only be set by the first SMB session set up
on the socket.
Signed-off-by: Jeff Layton <jlayton@tupile.poochiereds.net>
Signed-off-by: Steve French <sfrench@us.ibm.com>
When cifs_mount finds an existing SMB session that it can use for a new
mount, it does not check to see whether that session is in need of being
reconnected. An easy way to reproduce:
1) mount //server/share1
2) watch /proc/fs/cifs/DebugData for the share to go DISCONNECTED
3) mount //server/share2 with same creds as in step 1.
The second mount will fail because CIFSTCon returned -EAGAIN. If you do
an operation in share1 and then reattempt the mount it will work (since
the session is reestablished).
The following patch fixes this by having cifs_mount check the status
of the session when it picks an existing session and calling
cifs_setup_session on it again if it's in need of reconnection.
Thanks to Wojciech Pilorz for the initial bug report.
Signed-off-by: Jeff Layton <jlayton@tupile.poochiereds.net>
Signed-off-by: Steve French <sfrench@us.ibm.com>
The SPNEGO key data is not terribly interesting except in certain
debugging situations. Only dump it to the ring buffer if needed.
Signed-off-by: Jeff Layton <jlayton@tupile.poochiereds.net>
Signed-off-by: Steve French <sfrench@us.ibm.com>
access_flags_to_mode() gets on-the-wire data (little-endian) and treats
it as host-endian.
Introduced in commit e01b640013 ("[CIFS]
enable get mode from ACL when cifsacl mount option specified")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix RedHat bug 329431
The idea here is separate "conscious" from "unconscious" flushes.
Conscious flushes are those due to a fsync() or close(). Unconscious
ones are flushes that occur as a side effect of some other operation or
due to memory pressure.
Currently, when an error occurs during an unconscious flush (ENOSPC or
EIO), we toss out the page and don't preserve that error to report to
the user when a conscious flush occurs. If after the unconscious flush,
there are no more dirty pages for the inode, the conscious flush will
simply return success even though there were previous errors when writing
out pages. This can lead to data corruption.
The easiest way to reproduce this is to mount up a CIFS share that's
very close to being full or where the user is very close to quota. mv
a file to the share that's slightly larger than the quota allows. The
writes will all succeed (since they go to pagecache). The mv will do a
setattr to set the new file's attributes. This calls
filemap_write_and_wait,
which will return an error since all of the pages can't be written out.
Then later, when the flush and release ops occur, there are no more
dirty pages in pagecache for the file and those operations return 0. mv
then assumes that the file was written out correctly and deletes the
original.
CIFS already has a write_behind_rc variable where it stores the results
from earlier flushes, but that value is only reported in cifs_close.
Since the VFS ignores the return value from the release operation, this
isn't helpful. We should be reporting this error during the flush
operation.
This patch does the following:
1) changes cifs_fsync to use filemap_write_and_wait and cifs_flush and also
sync to check its return code. If it returns successful, they then check
the value of write_behind_rc to see if an earlier flush had reported any
errors. If so, they return that error and clear write_behind_rc.
2) sets write_behind_rc in a few other places where pages are written
out as a side effect of other operations and the code waits on them.
3) changes cifs_setattr to only call filemap_write_and_wait for
ATTR_SIZE changes.
4) makes cifs_writepages accurately distinguish between EIO and ENOSPC
errors when writing out pages.
Some simple testing indicates that the patch works as expected and that
it fixes the reproduceable known problem.
Acked-by: Dave Kleikamp <shaggy@austin.rr.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
When retrying kernel_recvmsg() because of a short read, check returned
length against the remaining length, not against total length. This
avoids unneeded session reconnects which would otherwise occur when
kernel_recvmsg() finally returns zero when asked to read zero bytes.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Have CIFS_SessSetup call cifs_get_spnego_key when Kerberos is
negotiated. Use the info in the key payload to build a session
setup request packet. Also clean up how the request buffer in
the function is freed on error.
With appropriate user space helper (in samba/source/client). Kerberos
support (secure session establishment can be done now via Kerberos,
previously users would have to use NTLMv2 instead for more secure
session setup).
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
...and populate it with the hostname portion of the UNC string.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Move all of the kfree's sprinkled in the middle of the function to the
end, and have the code set rc and just goto there on error. Also zero
out the password string before freeing it. Looks like this should also
fix a potential memory leak of the prepath string if an error occurs
near the end of the function.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
request
In SendReceive() function in transport.c - it memcpy's
message payload into a buffer passed via out_buf param. The function
assumes that all buffers are of size (CIFSMaxBufSize +
MAX_CIFS_HDR_SIZE) , unfortunately it is also called with smaller
(MAX_CIFS_SMALL_BUFFER_SIZE) buffers. There are eight callers
(SMB worker functions) which are primarily affected by this change:
TreeDisconnect, uLogoff, Close, findClose, SetFileSize, SetFileTimes,
Lock and PosixLock
CC: Dave Kleikamp <shaggy@austin.ibm.com>
CC: Przemyslaw Wegrzyn <czajnik@czajsoft.pl>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
...and fix a couple of bugs in the NBD, CIFS and OCFS2 socket handlers.
Looking at the sock->op->shutdown() handlers, it looks as if all of them
take a SHUT_RD/SHUT_WR/SHUT_RDWR argument instead of the
RCV_SHUTDOWN/SEND_SHUTDOWN arguments.
Add a helper, and then define the SHUT_* enum to ensure that kernel users
of shutdown() don't get confused.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: Mark Fasheh <mark.fasheh@oracle.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6: (21 commits)
[CIFS] fix oops on second mount to same server when null auth is used
[CIFS] Fix stale mode after readdir when cifsacl specified
[CIFS] add mode to acl conversion helper function
[CIFS] Fix incorrect mode when ACL had deny access control entries
[CIFS] Add uid to key description so krb can handle user mounts
[CIFS] Fix walking out end of cifs dacl
[CIFS] Add upcall files for cifs to use spnego/kerberos
[CIFS] add OIDs for KRB5 and MSKRB5 to ASN1 parsing routines
[CIFS] Register and unregister cifs_spnego_key_type on module init/exit
[CIFS] implement upcalls for SPNEGO blob via keyctl API
[CIFS] allow cifs_calc_signature2 to deal with a zero length iovec
[CIFS] If no Access Control Entries, set mode perm bits to zero
[CIFS] when mount helper missing fix slash wrong direction in share
[CIFS] Don't request too much permission when reading an ACL
[CIFS] enable get mode from ACL when cifsacl mount option specified
[CIFS] ACL support part 8
[CIFS] acl support part 7
[CIFS] acl support part 6
[CIFS] acl support part 6
[CIFS] remove unused funtion compile warning when experimental off
...
When a share is mounted using no username, cifs_mount sets
volume_info.username as a NULL pointer, and the sesInfo userName as an
empty string. The volume_info.username is passed to a couple of other
functions to see if there is an existing unc or tcp connection that can
be used. These functions assume that the username will be a valid
string that can be passed to strncmp. If the pointer is NULL, then the
kernel will oops if there's an existing session to which the string
can be compared.
This patch changes cifs_mount to set volume_info.username to an empty
string in this situation, which prevents the oops and should make it
so that the comparison to other null auth sessions match.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
When mounted with cifsacl mount option, readdir can not
instantiate the inode with the estimated mode based on the ACL
for each file since we have not queried for the ACL for
each of these files yet. So set the refresh time to zero
for these inodes so that the next stat will cause the client
to go to the server for the ACL info so we can build the estimated
mode (this means we also will issue an extra QueryPathInfo if
the stat happens within 1 second, but this is trivial compared to
the time required to open/getacl/close for each).
ls -l is slower when cifsacl mount option is specified, but
displays correct mode information.
Signed-off-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
When mounted with the cifsacl mount option, we were
treating any deny ACEs found like allow ACEs and it turns out for
SFU and SUA Windows set these type of access control entries often.
The order of ACEs is important too. The canonical order that most
ACL tools and Windows explorer consruct ACLs with is to begin with
DENY entries then follow with ALLOW, otherwise an allow entry
could be encountered first, making the subsequent deny entry like "dead
code which would be superflous since Windows stops when a match is
made for the operation you are trying to perform for your user
We start with no permissions in the mode and build up as we find
permissions (ie allow ACEs). This fixes deny ACEs so they affect
the mask used to set the subsequent allow ACEs.
Acked-by: Shirish Pargaonkar <shirishp@us.ibm.com>
CC: Alexander Bokovoy <ab@samba.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Adds uid to key description fro supporting user mounts
and minor formating changes
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Igor Mammedov <niallain@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Also, fix the parser to recognize them and set the secType
accordingly. Make CIFSSMBNegotiate not error out automatically
after parsing the securityBlob.
Also thanks to Q (Igor) and Simo for their help on this
set of kerberos patches (and Dave Howells for help on the
upcall).
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Add routines to handle upcalls to userspace via keyctl for the purpose
of getting a SPNEGO blob for a particular uid and server combination.
Clean up the Makefile a bit and set it up to only compile cifs_spnego
if CONFIG_CIFS_UPCALL is set. Also change CONFIG_CIFS_UPCALL to depend
on CONFIG_KEYS rather than CONFIG_CONNECTOR.
cifs_spnego.h defines the communications between kernel and userspace
and is intended to be shared with userspace programs.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Currently, cifs_calc_signature2 errors out if it gets a zero-length
iovec. Fix it to silently continue in that case.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Kernel bugzilla bug #9228
If mount helper (mount.cifs) missing, mounts with form like
//10.11.12.13/c$ would not work (only mounts with slash e.g.
//10.11.12.13\\c$ would work) due to problem with slash supposed
to be converted to backslash by the mount helper (which is not
there).
If we fail on converting an IPv4 address in in4_pton then
try to canonicalize the first slash (ie between sharename
and host ip address) if necessary. If we have to retry
to check for IPv6 address the slash is already converted
if necessary.
Signed-off-by: Steve French <sfrench@us.ibm.com>
We were requesting GENERIC_READ but that fails when we do not have
read permission on the file (even if we could read the ACL).
Also move the dump access control entry code into debug ifdef.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Part 9 of ACL patch series. getting mode from ACL now works in
some cases (and requires CIFS_EXPERIMENTAL config option).
Signed-off-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Now GetACL in getinodeinfo path when cifsacl mount option used, and
ACL is parsed for SIDs. Missing only one piece now to be able
to retrieve the mode
Signed-off-by: Steve French <sfrench@us.ibm.com>
get rid of couple of unused function warnings which
show up when CONFIG_CIFS_EXPERIMENTAL is not defined - wrap them in
#ifdef CONFIG_CIFS_EXPERIMENTAL. Patch against current git.
Signed-off-by: Parag Warudkar <kernel-stuff@comcast.net>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Now that nfsd has stopped writing to the find_exported_dentry member we an
mark the export_operations const
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Neil Brown <neilb@suse.de>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: <linux-ext4@vger.kernel.org>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: David Chinner <dgc@sgi.com>
Cc: Timothy Shimmin <tes@sgi.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Chris Mason <mason@suse.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: "Vladimir V. Saveliev" <vs@namesys.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6: (51 commits)
[CIFS] log better errors on failed mounts
[CIFS] Return better error when server requires signing but client forbids
[CIFS] fix typo
[CIFS] acl support part 4
[CIFS] Fix minor problems noticed by scan
[CIFS] fix bad handling of EAGAIN error on kernel_recvmsg in cifs_demultiplex_thread
[CIFS] build break
[CIFS] endian fixes
[CIFS] endian fixes in new acl code
[CIFS] Fix some endianness problems in new acl code
[CIFS] missing #endif from a previous patch
[CIFS] formatting fixes
[CIFS] Break up unicode_sessetup string functions
[CIFS] parse server_GUID in SPNEGO negProt response
[CIFS]
[CIFS] Fix endian conversion problem in posix mkdir
[CIFS] fix build break when lanman not enabled
[CIFS] remove two sparse warnings
[CIFS] remove compile warnings when debug disabled
[CIFS] CIFS ACL support part 3
...
The task_struct->pid member is going to be deprecated, so start
using the helpers (task_pid_nr/task_pid_vnr/task_pid_nr_ns) in
the kernel.
The first thing to start with is the pid, printed to dmesg - in
this case we may safely use task_pid_nr(). Besides, printks produce
more (much more) than a half of all the explicit pid usage.
[akpm@linux-foundation.org: git-drm went and changed lots of stuff]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also returns more accurate errors to mount for the cases of
account expired and password expired
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
If the ATTR_KILL_S*ID bits are set then any mode change is only for clearing
the setuid/setgid bits. For CIFS, skip the mode change and let the server
handle it.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When kernel_recvmsg returns -EAGAIN or -ERESTARTSYS, then
cifs_demultiplex_thread sleeps for a bit and then tries the read again.
When it does this, it's not zeroing out the length and that throws off
the value of total_read. Fix it to zero out the length.
Can cause memory corruption:
If kernel_recvmsg returns an error and total_read is a large enough
value, then we'll end up going through the loop again. total_read will
be a bogus value, as will (pdu_length-total_read). When this happens we
end up calling kernel_recvmsg with a bogus value (possibly larger than
the current iov_len).
At that point, memcpy_toiovec can overrun iov. It will start walking
up the stack, casting other things that are there to struct iovecs
(since it assumes that it's been passed an array of them). Any pointer
on the stack at an address above the kvec is a candidate for corruption
here.
Many thanks to Ulrich Obergfell for pointing this out.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Slab constructors currently have a flags parameter that is never used. And
the order of the arguments is opposite to other slab functions. The object
pointer is placed before the kmem_cache pointer.
Convert
ctor(void *object, struct kmem_cache *s, unsigned long flags)
to
ctor(struct kmem_cache *s, void *object)
throughout the kernel
[akpm@linux-foundation.org: coupla fixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SPNEGO setup needs only some of these strings. Break up
unicode_ssetup_strings so we can call them individually.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
SPNEGO NegProt response also contains a server_GUID. Parse it as we
would for RawNTLMSSP.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
[CIFS] fix error message about packet signing
When packet signing is disabled and the server requires it, cifs prints
an error message. The current message refers to a file in /proc that no
longer exists. Fix it to refer to the correct file.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Fixes two problems:
1) we dropped down to negotiating lanman if we did not recognize the
mechanism (krb5 e.g.)
2) we did not stop cifsd (thus will fail when doing rmod cifs with
slab free errors) when we fail tcon but have a bad session (which is
the case in which signing is required but we don't allow signing on
the client)
It also turns on extended security flag in the header when passing
"sec=krb5" on mount command (although kerberos support is not done of
course)
Acked-by: Jeff Layton <jlayton@redhat.com>
CC: Shaggy <shaggy@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This patch does kmalloc + memset conversion to kzalloc and removes some
redundant argument checks.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
When find_writable_file is racing with close and the session
to the server goes down, Shaggy noticed that there was a
chance that an open file in the list of files off the inode
could have been freed by close since cifs_reconnect can
block (the spinlock thus not held). This means that
we have to start over at the beginning of the list in some
cases.
There is a 2nd change that needs to be made later
(pointed out by Jeremy Allison and Shaggy) in order to
prevent cifs_close ever freeing the cifs per file info
when a write is pending. Although we delay close from
freeing this memory for sufficiently long for all known
cases, ultimately on a very, very slow write
overlapping a close pending we need to allow close to return
(without freeing the cifs file info) and defer freeing the
memory to be the responsibility of the (sloooow) write
thread (presumably have to look at every place wrtPending
is decremented - and add a flag for deferred free for
after wrtPending goes to zero).
Acked-by: Shaggy <shaggy@us.ibm.com>
Acked-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This allows cifs to mount to ipc shares (IPC$)
which will allow user space applications to
layer over authenticated cifs connections
(useful for Wine and others that would want
to put DCE/RPC over CIFS or run CIFS named
pipes)
Acked-by: Rob Shearman <rob@codeweavers.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
We were allocating request buffers twice in the statfs
path when mounted to very old (Windows 9x) servers.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Add code to be able to dump CIFS ACL information
when Query Posix ACL with cifsacl mount parm enabled.
Signed-off-by: Shirish Pargoankar <shirishp@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
A reasonably common NAS server returns an error on the SetFSInfo of
the Unix capabilities. Log a message for this alerting the user
that the server may have problems with the Unix extensions,
and telling them what they can do to workaround it.
Unfortunately the server does not return other clues
that we could easily use to turn the Unix Extension support
off automatically in this case (since they claim to support it).
Signed-off-by: Steve French <sfrench@us.ibm.com>
There is a small memory leak in fs/cifs/inode.c::cifs_mkdir().
Storage for 'pInfo' is allocated with kzalloc(), but if the call
to CIFSPOSIXCreate(...) happens to return 0 and pInfo->Type == -1,
then we'll jump to the 'mkdir_get_info' label without freeing the
storage allocated for 'pInfo'.
This patch adds a kfree() call to free the storage just before
jumping to the label, thus getting rid of the leak.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
When making a directory with POSIX mkdir calls, cifs_mkdir does not
respect the umask. This patch causes the new POSIX mkdir to create with
the right mode
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Harmless since it only protected turning off caching for the
inode, but cleaner to lock around this in case we have a close
racing with open.
Signed-off-by: Shaggy <shaggy@us.ibm.com>
CC: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
There was a case in which find_writable_file was not waiting long enough
under heavy stress when writepages was racing with close of the file
handle being used by the write.
Signed-off-by: Steve French <sfrench@us.ibm.com>
cifs reconnect could end up happening incorrectly due to
the small initial tcp recvmsg response. When the socket
was within three bytes of being full and the recvmsg
returned only 1 to 3 bytes of the initial 4 byte
read of the RFC1001 length field. Fortunately this
seems to be less common on more current kernels, but
this fixes it so cifs tries to retrieve all 4 bytes
of the initial tcp read.
Signed-off-by: Shirish Pargoankar <shirishp@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
On a mount without posix extensions enabled, when an unlock request is
made, the client can release more than is intended. To reproduce, on a
CIFS mount without posix extensions enabled:
1) open file
2) do fcntl lock: start=0 len=1
3) do fcntl lock: start=2 len=1
4) do fcntl unlock: start=0 len=1
...on the unlock call the client sends an unlock request to the server
for both locks. The problem is a bad test in cifs_lock.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
vmtruncate had added the same fix to handle the case of private pages
being Copy on writed while truncate_inode_pages is going on
Signed-off-by: Steve French <sfrench@us.ibm.com>
Caused by unneeded reopen during reconnect while spinlock held.
Fixes kernel bugzilla bug #7903
Thanks to Lin Feng Shen for testing this, and Amit Arora for
some nice problem determination to narrow this down.
Acked-by: Dave Kleikamp <shaggy@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously the only way to do this was to umount all mounts to that server,
turn off a proc setting (/proc/fs/cifs/LinuxExtensionsEnabled).
Fixes Samba bugzilla bug number: 4582 (and also 2008)
Signed-off-by: Steve French <sfrench@us.ibm.com>
currently the export_operation structure and helpers related to it are in
fs.h. fs.h is already far too large and there are very few places needing the
export bits, so split them off into a separate header.
[akpm@linux-foundation.org: fix cifs build]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
It's common for file systems to need to zero data on either side of a
write, if a page is not Uptodate during prepare_write. It just so happens
that simple_prepare_write() in libfs.c does exactly that, so we can avoid
duplication and just call that function to zero page data.
Signed-off-by: Nate Diller <nate.diller@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
In the cleanup phase of the dbench test, we were noticing sharing
violation followed by failed directory removals when dbench
did not close the test files before the cleanup phase started.
Using the new POSIX unlink, which Samba has supported for a few
months, avoids this.
Signed-off-by: Steve French <sfrench@us.ibm.com>
This should be the last big batch of whitespace/formatting fixes.
checkpatch warnings for the cifs directory are down about 90% and
many of the remaining ones are harder to remove or make the code
harder to read.
Signed-off-by: Steve French <sfrench@us.ibm.com>
nfsd is passing null nameidata (probably the only one doing that)
on call to create - cifs was missing one check for this.
Note that running nfsd over a cifs mount requires specifying fsid on
the nfs exports entry and requires mounting cifs with serverino mount
option.
Signed-off-by: Steve French <sfrench@us.ibm.com>
They can use generic_file_splice_read() instead. Since sys_sendfile() now
prefers that, there should be no change in behaviour.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Currently, if mount with a signing-enabled sec= option (e.g.
sec=ntlmi), the kernel does a warning printk if the server doesn't
support signing, and then proceeds without signatures.
This is probably OK for people that think to look at the ring buffer,
but seems wrong to me. If someone explicitly requests signing, we
should error out if that request can't be satisfied. They can then
reattempt the mount without signing if that's ok.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
We were checking the wrong (old) global variable to determine
whether to override server and force signing on the SMB
connection.
Acked-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Switch from send_sig to force_sig and do not allow signal for this
background thread (the signal is needed to wakeup the thread when
blocked in the network stack).
Signed-off-by: Jeff Layton <jlayton@readhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This patch makes CIFS honour a process' umask like other filesystems.
Of course the server is still free to munge the permissions if it wants
to; but the client will send the "right" permissions to begin with.
A few caveats:
1) It only applies to filesystems that have CAP_UNIX (aka support unix
extensions)
2) It applies the correct mode to the follow up CIFSSMBUnixSetPerms()
after remote creation
When mode to CIFS/NTFS ACL mapping is complete we can do the
same thing for that case for servers which do not
support the Unix Extensions.
Signed-off-by: Matt Keenen <matt@opcode-solutions.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
A related signature issue that I came across.
There's a bug in win2k that when NT error codes are not negotiated, the
server doesn't response that signatures are mandatory. Since there's
(currently) no way turn on signatures in such case, I had to force NT
error codes, so that this bug will not occur
Signed-off-by: Yehuda Sadeh Weinraub <Yehuda.Sadeh@expand.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Various coding style problems found by running the new
checkpatch.pl script against fs/cifs. 3 more files
fixed up.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Various coding style problems found by running fs/cifs
against the new checkpatch.pl script. Since there
were too many to fit in one patch. Updated the first
four files.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Slab cache used as memory pool can not be destroyed before the memory
pool destruction. Because the memory pool still holds some objects and
kmem_cache_destroy() says "Can't free all objects".
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
If the cifs demultiplex thread wakes up and exits
(zeroing server->tsk) before kthread_stop is called, the
cifs_mount code could pass a null pointer to kthread_stop
Thanks to akpm, Dave Young and Shaggy for suggesting
earlier versions of this patch.
CC: akpm@linux-foundatior.org
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
SLAB_CTOR_CONSTRUCTOR is always specified. No point in checking it.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@ucw.cz>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have never seen a use of SLAB_DEBUG_INITIAL. It is only supported by
SLAB.
I think its purpose was to have a callback after an object has been freed
to verify that the state is the constructor state again? The callback is
performed before each freeing of an object.
I would think that it is much easier to check the object state manually
before the free. That also places the check near the code object
manipulation of the object.
Also the SLAB_DEBUG_INITIAL callback is only performed if the kernel was
compiled with SLAB debugging on. If there would be code in a constructor
handling SLAB_DEBUG_INITIAL then it would have to be conditional on
SLAB_DEBUG otherwise it would just be dead code. But there is no such code
in the kernel. I think SLUB_DEBUG_INITIAL is too problematic to make real
use of, difficult to understand and there are easier ways to accomplish the
same effect (i.e. add debug code before kfree).
There is a related flag SLAB_CTOR_VERIFY that is frequently checked to be
clear in fs inode caches. Remove the pointless checks (they would even be
pointless without removeal of SLAB_DEBUG_INITIAL) from the fs constructors.
This is the last slab flag that SLUB did not support. Remove the check for
unimplemented flags from SLUB.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We had a customer report that attempting to make CIFS mount with a null
username (i.e. doing an anonymous mount) doesn't work. Looking through the
code, it looks like CIFS expects a NULL username from userspace in order
to trigger an anonymous mount. The mount.cifs code doesn't seem to ever
pass a null username to the kernel, however.
It looks also like the kernel can take a sec=none option, but it only seems
to look at it if the username is already NULL. This seems redundant and
effectively makes sec=none useless.
The following patch makes sec=none force an anonymous mount.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Originally at http://lkml.org/lkml/2006/9/2/86
The recent change to "allow Windows blocking locks to be cancelled via a
CANCEL_LOCK call" introduced a new semaphore in struct cifsFileInfo,
lock_sem. However, semaphores used as mutexes are deprecated these days,
and there's no reason to add a new one to the kernel. Therefore, convert
lock_sem to a struct mutex (and also fix one indentation glitch on one of
the lines changed anyway).
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Steve French