Some UARTs have more than 255 bytes of FIFO, which can't be
represented by an unsigned char. Change the kernel's internal
structure to be an unsigned int, but still export an unsigned char
via the TIOCGSERIAL ioctl. If the TIOCSSERIAL ioctl provides a
fifo size of 0, assume this means "don't change" otherwise we'll
corrupt the larger fifo sizes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When there is remaining blocks untransferred, we get two error messages saying
almost the same thing. Make sure at most one is shown.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some controllers incorrectly report that the cannot do DMA. Forcefully enable
it for those that we know it works fine on.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some controllers fail to complete a reset unless you touch the clock register
first.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There was a logic fault in scsi_io_completion() where zero transfer
commands that complete successfully were sent to the block layer as
not up to date. This patch removes the if (good_bytes > 0) gate
around the successful completion, since zero transfer commands do have
good_bytes == 0.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New version number for sdhci driver.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As some specific controllers will have bugs, we need a way to map special
behaviour to certain hardware.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Properly test for controller interface to see if it's DMA capable. As many
controllers are misconfigured in this regard, also add debug parameters to
force DMA support either way.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The specification states that the capabilities register might need a reset to
get correct values after boot up.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Check the interface version of the controller and bail out if it's an unknown
version.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Conform to the sdhci specification as to which inhibit bits should be checked
at different times.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The controller has an upper limit on the block size. Make sure we do not
cross it.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci controllers will issue an interrupt when a configurable number of
bytes have been transfered using DMA. The purpose is to handle multiple,
scattered memory pages.
Unfortunately, it requires that all transfers are completely aligned to
memory pages, which we cannot guarantee. So we just disable the function.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci controllers operate with blocks, not bytes. The PIO routines must
therefore make sure that the minimum unit transfered is a complete block.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The specification says that interrupts should be cleared before the source is
removed. We should also not set unknown bits.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci specification states that some registers must be written to in a
specific order.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the give timeout clock and calculate a proper timeout instead of using the
maximum at all times.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The reset register is automatically cleared when the reset has completed.
Hence, we should busy wait and not have a fixed delay.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current timeout loop assume that jiffies are updated. This might not be
the case depending on locks and if the kernel is compiled without preemption.
Change the system to use a counter and fixed delays.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci controllers can support up to three voltage levels. Detect which
and report back to the MMC layer.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As sdhci is a generic driver, it is helpful to see some more specific
identification of the actual hardware in dmesg. PCI vendor, device and
revision is sufficient in most cases.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A base clock value of 0 means that the driver must get the base clock through
some other means. As we have no other way of getting it, we must abort.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 64 bits resource patches did a bit of damage on PowerMac causing a
buffer overflow in macio_asic and a warning in a sound driver. The
former is fixed by reverting the sprintf of the bus_id to %08x as it was
before. The bus_id used for macio devices is always a 32 bits value
(macio always sits in 32 bits space) and since it's exposed to userland,
the format of the string shouldn't be changed like that anyway. The
second by using the proper type for printk.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Include the generic header file instead of the ARM specific one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Include the generic header file instead of the ARM specific one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most batteries today are ACPI "Control Method" batteries,
but some models ship with the older "Smart Battery"
that requires this code.
Rich Townsend and Bruno Ducrot were the original authors.
Vladimir Lebedev updated to run on latest kernel.
http://bugzilla.kernel.org/show_bug.cgi?id=3734
Signed-off-by: Len Brown <len.brown@intel.com>
This patch switches back the display nodes for M6R and M6N -- this happened
a while ago when a patch was misapplied (only the in-tree version was
affected).
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Patch from Tony Lindgren
This patch makes OMAP MMC work again:
- Fix compile errors
- Do not ioremap base as it is already statically mapped
- Clean-up platform device handling
- Fix compile warnings
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suppress the "setup_irq: irq handler mismatch" coming out of pnp_check_irq():
failures are expected here.
Cc: <stable@kernel.org>
Cc: Santiago Garcia Mantinan <manty@manty.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Network Block Device driver doesn't compile if NDEBUG is defined.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Missing variable initialisation would mean it would sometimes not put ATAPI
devices into DMA by default.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: <Jack.Lee@ite.com.tw>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a renamed and tested version of the previous S3C24XX RTC class
driver.
The driver has been renamed from the original s3c2410-rtc, which is now too
narrow for the range of devices supported.
The rtc-s3c has been chosen as there is the distinct possibility of this
driver being carried forward into newer Samsung SoC silicon.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove ips namespace from infinipath drivers. This renames ips_common.h to
ipath_common.h. Definitions, data structures, etc. that were not used by
kernel modules have moved to user-only headers. All names including ips have
been renamed to ipath. Some names have had an ipath prefix added.
Signed-off-by: Christian Bell <christian.bell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The receive work queue size should be ignored if the QP is created to use a
shared receive queue according to the IB spec.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We can't tell for sure if any packets are in the infinipath receive buffer
when we shut down a chip port. Normally this is taken care of by orderly
shutdown, but when processes are terminated, or sending process has a bug, we
can continue to receive packets. So rather than writing zero to the address
registers for the closing port, we point it at a dummy memory.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We must increment uaddr by size we are reading or writing, since it's passed
as a char *, not a pointer to the appropriate size.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We do a few more explicit checks for specific models, and now also support the
old PathScale serial number style, or new QLogic style.
This is backwards compatible with previous versions of software and hardware.
That is, older software will see a plausible serial number and correct GUID
when used with a new board, while newer software will correctly handle an
older board.
Signed-off-by: Mike Albaugh <mike.albaugh@qlogic.com>
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This attribute group made it into the original driver, but should not have.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The two arrays only had space for 4 units.
Also changed from ipath_set_sps_lid() to ipath_set_lid(); the sps was
leftover.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch separates QP state used for sending and receiving RC packets so the
processing in the receive interrupt handler can be done mostly without locks
being held. ACK packets are now sent without requiring synchronization with
the send tasklet.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes some problems uncovered during IB compliance testing to
return the right values for error counters returned by the Performance Get
Counters packet.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The tail register read became redundant as the result of earlier receive
interrupt bug fixes.
Drop another unneeded register read.
And another line that got duplicated.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do an extra check to see if in-memory tail changed while processing packets,
and if so, going back through the loop again (but only once per call to
ipath_kreceive()). In practice, this seems to be enough to guarantee that if
we crossed the clearing of an interrupt at start of ipath_intr with a
scheduled tail register update, that we'll process the "extra" packet that
lost the interrupt because we cleared it just as it was about to arrive.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The problem was that I was updating the head register multiple times in the
rcvhdrq processing loop, and setting the counter on each update. Since that
meant that the tail register was ahead of head for all but the last update, we
would get extra interrupts. The fix was to not write the counter value except
on the last update.
I also changed to update rcvhdrhead and rcvegrindexhead at most every 16
packets, if there were lots of packets in the queue (and of course, on the
last packet, regardless).
I also made some small cleanups while debugging this.
With these changes, xeon/monty typically sees two openib packets per interrupt
on sdp and ipoib, opteron/monty is about 1.25 pkts/intr.
I'm seeing about 3800 Mbit/s monty/xeon, and 5000-5100 opteron/monty with
netperf sdp. Netpipe doesn't show as good as that, peaking at about 4400 on
opteron/monty sdp. Plain ipoib xeon is about 2100+ netperf, opteron 2900+, at
128KB
Signed-off-by: olson@eng-12.pathscale.com
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also count the number of interrupts where that works (fastrcvint). On any
interrupt where the port0 head and tail registers are not equal, just call the
ipath_kreceive code without reading the interrupt status, thus saving the
approximately 0.25usec processor stall waiting for the read to return. If any
other interrupt bits are set, or head==tail, take the normal path, but that
has been reordered to handle read ahead of pioavail. Also no longer call
ipath_kreceive() from ipath_qcheck(), because that just seems to make things
worse, and isn't really buying us anything, these days.
Also no longer loop in ipath_kreceive(); better to not hold things off too
long (I saw many cases where we would loop 4-8 times, and handle thousands (up
to 3500) in a single call).
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Made in-memory rcvhdrq tail update be in dma_alloc'ed memory, not random user
or special kernel (needed for ppc, also "just the right thing to do").
Some cleanups to make unexpected link transitions less likely to produce
complaints about packet errors, and also to not leave SMA packets stuck and
unable to go out.
A few other random debug and comment cleanups.
Always init rcvhdrq head/tail registers to 0, to avoid race conditions (should
have been that way some time ago).
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is not a DMA target, so no need to use dma_alloc_coherent on it.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This helps us to survive better when memory is fragmented.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These limits are somewhat artificial in that we don't actually have any
device limits. However, the verbs layer expects that such limits exist
and are enforced, so we make up arbitrary (but sensible) limits.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is no longer a /dev/ipath_diag file; instead, there's
/dev/ipath_diag0, 1, etc.
It's still not possible to have diags run on more than one unit at a time,
but that's easy to fix at some point.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the quoted module name in the sysfs for EDAC modules and reported by several
people.
Instead of ../_edac_e752x_/ now the following will be presented, like other
modules: ../edac_e752x/
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix section mismatch warnings:
WARNING: drivers/scsi/qla1280.o - Section mismatch: reference to
.init.data: from .text between 'qla1280_get_token' (at offset 0x2a16)
and 'qla1280_probe_one'
WARNING: drivers/scsi/qla1280.o - Section mismatch: reference to
.init.data: from .text between 'qla1280_get_token' (at offset 0x2a3c)
and 'qla1280_probe_one'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
One of the current problems the mptsas driver has is that of "ghost"
devices (these are devices the firmware reports as existing, but what
they actually represent are the parents of a lower device), so for
example in my dual expander configuration, three expanders actually show
up, two for the real expanders but a third is created because the
firmware reports that the lower expander also has another expander
connected (which is simply the port going back to the upper expander).
The attached patch eliminates all these ghosts by not allocating any
devices for them if the SAS address is the SAS address of the parent.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make some needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add a few spaces to MODULE_PARM_DESC() text for qla2xxx. Without these
spaces text runs together when modinfo prints the text.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The way mpt_interrupt() was coded, it was impossible for the unhandled
interrupt detection logic to ever trigger. All interrupt handlers should
return IRQ_NONE when they have nothing to do.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I got a NULL derefrence in cdev_del+1 when called from sg_remove. By looking at
the code of sg_add, sg_alloc and sg_remove (all in drivers/scsi/sg.c) I found
out that sg_add is calling sg_alloc but if it fails afterwards it does not
deallocate the space that was allocated in sg_alloc and the redundant entry has
NULL in cdev. When sg_remove is being called, it tries to perform cdev_del to
this NULL cdev and fails.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch switches back the display nodes for M6R and M6N -- this happened
a while ago when a patch was misapplied (only the in-tree version was
affected).
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This small patch adds back WLED control for S1N models, this was
accidentally removed a while ago.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch reworks laptop model detection.
This addresses the Samsung P30 issue, where the INIT method would return no
object, but the implicit return in the AML interpreter would confuse the
driver. It also accounts for a newer batch of Asus models whose INIT
returns ACPI_TYPE_BUFFER instead of STRING.
The handling is now much leaner, if we get a buffer or a string, we check
against known values, in every other case we use a different path
(currently DSDT signatures). The bulk of this patch is separating the
string matching from asus_hotk_get_info() into a separate function.
This patch properly fixes http://bugme.osdl.org/show_bug.cgi?id=5067 and
http://bugme.osdl.org/show_bug.cgi?id=5092 and makes the driver fully
functional again with acpi=strict on all machines.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds support for Asus L5D and thus fixes
http://bugme.osdl.org/show_bug.cgi?id=4695
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch creates a new file named "bluetooth" under /proc/acpi/asus/.
This file controls both the internal Bluetooth adapter's presence on the
USB bus and the associated LED.
echo 1 > /proc/acpi/asus/bluetooth to enable, 0 to disable.
Additionally, the patch add support for Asus W5A, the first model that uses
this feature.
Patch originally by Fernando A. P. Gomes.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds support for Asus A4G.
Originally by Giuseppe Rota.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds handling for front LED displays found on W1N and the like.
Additionally, W1N is given its own model_data instance.
Patch originally by Éric Burghard.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch updates the version string, copyright notices and does
whitespace cleanup (it looks weird, blame Lindent).
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Kill sun4v virtual device layer.
[SERIAL] sunhv: Convert to of_driver layer.
[SPARC64]: Mask out top 8-bits in physical address when building resources.
[SERIAL] sunsu: Missing return statement in su_probe().
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPV6]: Added GSO support for TCPv6
[NET]: Generalise TSO-specific bits from skb_setup_caps
[IPV6]: Added GSO support for TCPv6
[IPV6]: Remove redundant length check on input
[NETFILTER]: SCTP conntrack: fix crash triggered by packet without chunks
[TG3]: Update version and reldate
[TG3]: Add TSO workaround using GSO
[TG3]: Turn on hw fix for ASF problems
[TG3]: Add rx BD workaround
[TG3]: Add tg3_netif_stop() in vlan functions
[TCP]: Reset gso_segs if packet is dodgy
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/core: Set alternate port number when initializing QP attributes
IB/uverbs: Set correct user handle for user SRQs
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6/:
[PATCH] pcmcia: fix deadlock in pcmcia_parse_events
[PATCH] com20020_cs: more device support
[PATCH] au1xxx: pcmcia: fix __init called from non-init
[PATCH] kill open-coded offsetof in cm4000_cs.c ZERO_DEV()
[PATCH] pcmcia: convert pcmcia_cs to kthread
[PATCH] pcmcia: fix kernel-doc function name
[PATCH] pcmcia: hostap_cs.c - 0xc00f,0x0000 conflicts with pcnet_cs
[PATCH] pcmcia: at91_cf suspend/resume/wakeup
[PATCH] pcmcia: Make ide_cs work with the memory space of CF-Cards if IO space is not available
[PATCH] pcmcia: TI PCIxx12 CardBus controller support
[PATCH] pcmcia: warn if driver requests exclusive, but gets a shared IRQ
[PATCH] pcmcia: expose tool in pcmcia/Documentation/pcmcia/
[PATCH] pcmcia: another ID for serial_cs.c
[PATCH] yenta: fix hidden PCI bus numbers
[PATCH] yenta: do power-up only after socket is configured
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4290): Add support for the TCL M2523_3DB_E tuner.
V4L/DVB (4289): Missing statement in drivers/media/dvb/frontends/cx22700.c
V4L/DVB (4288): Clean out a zillion sparse warnings in pvrusb2
V4L/DVB (4287): Pvrusb2/: possible cleanups
V4L/DVB (4285): Cx88: add support for Geniatech Digistar / Digiwave 103g
V4L/DVB (4284): Cx24123: fix set_voltage function according to the specs
V4L/DVB (4282): Fix: use swzigzag for swalgo
V4L/DVB (4281): TDA9887_SET_CONFIG should only be handled by the tda9887.
V4L/DVB (4277): Fix CI interface on PRO KNC1 cards
V4L/DVB (4276): Fix CI on old KNC1 DVBC cards
V4L/DVB (4275): The FE_SET_FRONTEND_TUNE_MODE ioctl always returns EOPNOTSUPP
V4L/DVB (4274): Eliminate use of tda9887 from pvrusb2 driver
V4L/DVB (4273): Always log pvrusb2 device register / unregister events
V4L/DVB (4272): Fix tveeprom supported standards
V4L/DVB (4270): Add tda9887-specific tuner configuration
V4L/DVB (4269): Subject: videocodec: make 1-bit fields unsigned
V4L/DVB (4267): Remove all instances of request_module("tda9887")
V4L/DVB (4264): Cx88-blackbird: implement VIDIOC_QUERYCTRL and VIDIOC_QUERYMENU
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (25 commits)
ACPI: Kconfig: ACPI_SRAT depends on ACPI
ACPI: drivers/acpi/scan.c: make acpi_bus_type static
ACPI: fixup memhotplug debug message
ACPI: ACPICA 20060623
ACPI: C-States: only demote on current bus mastering activity
ACPI: C-States: bm_activity improvements
ACPI: C-States: accounting of sleep states
ACPI: additional blacklist entry for ThinkPad R40e
ACPI: restore comment justifying 'extra' P_LVLx access
ACPI: fix battery on HP NX6125
ACPIPHP: prevent duplicate slot numbers when no _SUN
ACPI: static-ize handle_hotplug_event_func()
ACPIPHP: use ACPI dock driver
ACPI: dock driver
KEVENT: add new uevent for dock
ACPI: asus_acpi_init: propagate correct return value
[ACPI] Print error message if remove/install notify handler fails
ACPI: delete tracing macros from drivers/acpi/*.c
ACPI: HW P-state coordination support
ACPI: un-export ACPI_ERROR() -- use printk(KERN_ERR...)
...
This patch adds GSO support for IPv6 and TCPv6. This is based on a patch
by Ananda Raju <Ananda.Raju@neterion.com>. His original description is:
This patch enables TSO over IPv6. Currently Linux network stacks
restricts TSO over IPv6 by clearing of the NETIF_F_TSO bit from
"dev->features". This patch will remove this restriction.
This patch will introduce a new flag NETIF_F_TSO6 which will be used
to check whether device supports TSO over IPv6. If device support TSO
over IPv6 then we don't clear of NETIF_F_TSO and which will make the
TCP layer to create TSO packets. Any device supporting TSO over IPv6
will set NETIF_F_TSO6 flag in "dev->features" along with NETIF_F_TSO.
In case when user disables TSO using ethtool, NETIF_F_TSO will get
cleared from "dev->features". So even if we have NETIF_F_TSO6 we don't
get TSO packets created by TCP layer.
SKB_GSO_TCPV4 renamed to SKB_GSO_TCP to make it generic GSO packet.
SKB_GSO_UDPV4 renamed to SKB_GSO_UDP as UFO is not a IPv4 feature.
UFO is supported over IPv6 also
The following table shows there is significant improvement in
throughput with normal frames and CPU usage for both normal and jumbo.
--------------------------------------------------
| | 1500 | 9600 |
| ------------------|-------------------|
| | thru CPU | thru CPU |
--------------------------------------------------
| TSO OFF | 2.00 5.5% id | 5.66 20.0% id |
--------------------------------------------------
| TSO ON | 2.63 78.0 id | 5.67 39.0% id |
--------------------------------------------------
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use GSO to workaround a rare TSO bug on some chips. This hardware
bug may be triggered when the TSO header size is greater than 80
bytes. When this condition is detected in a TSO packet, the driver
will use GSO to segment the packet to workaround the hardware bug.
Thanks to Juergen Kreileder <jk@blackdown.de> for reporting the
problem and collecting traces to help debug the problem.
And thanks to Herbert Xu <herbert@gondor.apana.org.au> for providing
the GSO mechanism that happens to be the perfect workaround for this
problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear a bit to enable a hardware fix for some ASF related problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add workaround to limit the burst size of rx BDs being DMA'ed to the
chip. This works around hardware errata on a number of 5750, 5752,
and 5755 chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tg3_netif_stop() when changing the vlgrp (vlan group) pointer. It
is necessary to quiesce the device before changing that pointer.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set alternate port number when initializing QP attributes. This bug
is OpenFabrics bugzilla bug #160.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Store away the user handle passed in from userspace when creating an
SRQ, so that the kernel can return the correct handle when an SRQ
asynchronous event occurs. (A 0 was incorrectly stored as the user
handle as part of the changes in 9ead190b, "IB/uverbs: Don't serialize
with ib_uverbs_idr_mutex")
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The PCMCIA layer calls pcmcia_parse_events both from user context and
IRQ context; the lock thus needs to be irqsave to avoid deadlocks
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Enable the com20020_cs arcnet driver to see the SoHard (now Mercury
Computer Systems Inc.) SH ARC-PCMCIA card.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This must not be marked __init, as it is called from
au1x00_drv_pcmcia_probe.
Signed-off-by: Domen Puncer <domen.puncer@ultra.si>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
... to make sure that it doesn't break again when a field changes (see
"[PATCH] pcmcia: fix zeroing of cm4000_cs.c data" for recent example).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Convert pcmcia_cs to use kthread instead of the deprecated
kernel_thread.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Comment out the ID 0xc00f,0x0000 in hostap_cs.c, as it conflicts with the
pcnet_cs driver.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
AT91 CF updates, mostly for power management:
- Add suspend/resume methods to the AT91 CF driver, disabling
non-wakeup IRQs during system suspend. The card detect IRQ
serves as a wakeup event source.
- Convert the driver to the more-current "platform_driver" style.
So inserting or removing a CF card will wake the system, unless that
has been disabled by updating the sysfs file; and there will be no
more warnings about spurious IRQs during suspend/resume cycles.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch enables ide_cs to access CF-cards via their common memory
rather than via their IO space.
Signed-off-by: Thomas Kleffel <tk@maintech.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The patch below adds support for the TI PCIxx12 CardBus controllers.
This seems to be sufficient to detect the cardbus bridge on an HP nc6320
and works with an orinoco wifi card.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The patch below cleans up the pcmcia code a bit on the IRQ side (I did
this while debugging the problem just so I could read wtf it was doing),
and also adds a warning and passes back the correct information when a
device asks for exclusive but gets given shared. This at least means the
dmesg dump of a problem triggered by this will have a signature to find.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Fixup the subordinate number parent bridge of yenta Cardbus Bridges
before the PCI bus scan starts to make the cardbus cards which are
otherwise hidden for PCI scans work.
Signed-off-by: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Power-up the card only after the socket is configured. power-down in
the old place. The point is not to power-up the card before the interrupt
routing is set up correctly.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Stumbled over this because of coverity (id #492),
seems like we are missing a return statement here and fail
to do proper bounds checking. If this assumption is false
we should at least change the identation to make it clear
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following possible cleanups:
- make needlessly global code static
- #if 0 unused global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the Geniatech Digistar, aka
Digiwave 103g DVB-S card.
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Saqeb Akhter <johoja@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The set_voltage function in cx24123.c was corrected to match how it is
described in the CX24123 specs, producing the correct behaviour for cards
that require it.
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Saqeb Akhter <johoja@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The original driver had a restriction that if a card as an saa7113 chip,
then it cannot have a CI interface. This is not the case.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These cards do not need the tda10021 configuration change when data is
streamed through a CAM module. This disables it for these ones.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When someone added the front-end ioctl FE_SET_FRONTEND_TUNE_MODE, they
forgot to set the return value to 0. It always returns EOPNOTSUPP,
causing problems for programmers who actually check for error conditions.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Previously the pvrusb2 driver was conditionalizing printing of the
device register / unregister messages against a debug mask. This sort
of information should always appear, thus this patch.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The supported standards by the tuner on tveeprom were too restricted.
It were showing just the main format, instead of the format family.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thomas Gleixner