Commit Graph

22560 Commits

Author SHA1 Message Date
Paul Stewart 3117bbdb78 mac80211: Don't let regulatory make us deaf
When regulatory information changes our HT behavior (e.g,
when we get a country code from the AP we have just associated
with), we should use this information to change the power with
which we transmit, and what channels we transmit.  Sometimes
the channel parameters we derive from regulatory information
contradicts the parameters we used in association.  For example,
we could have associated specifying HT40, but the regulatory
rules we apply may forbid HT40 operation.

In the situation above, we should reconfigure ourselves to
transmit in HT20 only, however it makes no sense for us to
disable receive in HT40, since if we associated with these
parameters, the AP has every reason to expect we can and
will receive packets this way.  The code in mac80211 does
not have the capability of sending the appropriate action
frames to signal a change in HT behaviour so the AP has
no clue we can no longer receive frames encoded this way.
In some broken AP implementations, this can leave us
effectively deaf if the AP never retries in lower HT rates.

This change breaks up the channel_type parameter in the
ieee80211_enable_ht function into a separate receive and
transmit part.  It honors the channel flags set by regulatory
in order to configure the rate control algorithm, but uses
the capability flags to configure the channel on the radio,
since these were used in association to set the AP's transmit
rate.

Signed-off-by: Paul Stewart <pstew@chromium.org>
Cc: Sam Leffler <sleffler@chromium.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R Rodriguez <mcgrof@frijolero.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-13 14:55:53 -04:00
Johannes Berg e9ac0745c7 mac80211: rename bss_conf timestamp to last_tsf
This value is not really very useful by itself,
yet some drivers (including iwlwifi until I can
figure out what it should do) use it. At least
rename it to "last_tsf" to indicate the meaning
and add a note that it may be really old.

I suspect the value may become useful combined
with the rx_status->mactime, but we don't (yet)
store that value and pass it to the driver.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-13 14:54:20 -04:00
Johannes Berg 7b8bcff2e0 cfg80211: clarify timestamp in cfg80211_inform_bss
This is intended to be the timestamp sent by the
peer in the beacon/probe response, not any form
of host timestamp. Clarify the documentation and
variable names.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-13 14:54:20 -04:00
Johannes Berg a828691188 mac80211: linearize SKBs as needed for crypto
Not linearizing every SKB will help actually pass
non-linear SKBs all the way up when on an encrypted
connection. For now, linearize TKIP completely as
it is lower performance and I don't quite grok all
the details.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-13 14:54:17 -04:00
Johannes Berg 617bbde878 mac80211: move RX WEP weak IV counting
This is better done inside the WEP decrypt
function where it doesn't have to check all
the conditions any more since they've been
tested already.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-13 14:54:16 -04:00
Joe Perches afd465030a net: ipv4: Standardize prefixes for message logging
Add #define pr_fmt(fmt) as appropriate.

Add "IPv4: ", "TCP: ", and "IPsec: " to appropriate files.
Standardize on "UDPLite: " for appropriate uses.
Some prefixes were previously "UDPLITE: " and "UDP-Lite: ".

Add KBUILD_MODNAME ": " to icmp and gre.
Remove embedded prefixes as appropriate.

Add missing "\n" to pr_info in gre.c.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-12 17:05:21 -07:00
Ingo Molnar 35239e23c6 Merge branch 'perf/urgent' into perf/core
Merge reason: We are going to queue up a dependent patch.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2012-03-12 20:44:11 +01:00
Johannes Berg 5d6a1b069b mac80211: set basic rates earlier
The authentication and association handshake
already happens in the context of the new BSS,
and the basic rates are needed at least for
the ACK response frame to the authentication
or association response frames. Therefore the
basic rates should already be configured into
the driver when those frames are sent.

Change the logic to set up the basic rates in
the connection preparation that happens for
authentication and association (if needed).

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12 14:22:16 -04:00
Johannes Berg a1cf775dea mac80211: refactor common auth/assoc setup code
As associating is possible without first authenticating
(for FT over DS) association also has to be able to
switch to the right channel, insert the station entry
etc. Factor out this common code into a new function
called ieee80211_prep_connection().

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12 14:22:15 -04:00
Johannes Berg 0775f9f90c mac80211: remove spurious BSSID change flag
The BSSID has been set a lot earlier already and
didn't change again in ieee80211_set_associated().

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12 14:22:14 -04:00
Johannes Berg 76f0303d61 mac80211: simplify wmm check during association
Instead of setting assoc_data->wmm_used solely
based on the BSS also take into account our own
capabilities and later check those.

Also rename "wmm_used" and "uapsd_used" to just
"wmm" and "uapsd".

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12 14:22:13 -04:00
Johannes Berg 4e74bfdb30 mac80211: simplify HT checks
Always set/use IEEE80211_STA_DISABLE_11N instead
of duplicating the queue, WMM and HT checks in
all places.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12 14:22:12 -04:00
Johannes Berg de5036aae6 mac80211: move misplaced comment
Looks like some changes in this area moved
the code but not the comment that belongs
to the code, move it to the right place.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12 14:22:11 -04:00
Helmut Schaa e9219779f9 mac80211: Disable MCS > 7 in minstrel_ht when STA uses static SMPS
Disable multi stream rates (MCS > 7) when a STA is in static SMPS mode
since it has only one active rx chain. Hence, it doesn't even make
sense to sample multi stream rates.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12 14:19:39 -04:00
Johannes Berg 3cc5240b5e mac80211: set channel back after disassociating
As we've discussed, we want to avoid channel changes
while associated. While the part when we actually
associate needs a bit more work, the bit that happens
on disassociating can be changed quite easily. Move
the channel type change later in the disassociate
process to set the channel only after the driver was
told that it's now disassociated.

As the driver could expect powersave to be enabled
only when associated, this thus results in splitting
the config call, but overall what happens makes more
sense this way.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12 14:19:38 -04:00
Johannes Berg 177958e967 mac80211: remove tx_sync
When the station state callback was added, this
was no longer needed in theory. With the iwlwifi
changes to remove use of it landing, we can kill
the entire tx-sync framework again, RIP.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12 14:19:38 -04:00
Helmut Schaa aa45458060 mac80211: Limit TID buffering during BA session setup/teardown
While setting up or tearing down a BA session mac80211 is buffering
pending frames for the according TID. However, there's currently no
limit on how many frames are buffered possibly leading to an out-of-
memory situation. This can happen on systems with little memory when
the CPU is fully loaded since the BA session work is executed in
process context while frames can still come via softirq.

Apply a limitation to the TIDs pending queue to avoid consuming
too much memory in this situation.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12 14:19:35 -04:00
Bala Shanmugam 4486ea987e cfg80211: Add background scan period attribute.
Receive background scan period as part of connect
command and pass the same to the driver.

Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12 14:19:34 -04:00
Trond Myklebust 0097143c12 SUNRPC: Don't use variable length automatic arrays in kernel code
Replace the variable length array in the RPCSEC_GSS crypto code with
a fixed length one. The size should be bounded by the variable
GSS_KRB5_MAX_BLOCKSIZE, so use that.

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2012-03-12 13:37:16 -04:00
Joe Perches 058bd4d2a4 net: Convert printks to pr_<level>
Use a more current kernel messaging style.

Convert a printk block to print_hex_dump.
Coalesce formats, align arguments.
Use %s, __func__ instead of embedding function names.

Some messages that were prefixed with <foo>_close are
now prefixed with <foo>_fini.  Some ah4 and esp messages
are now not prefixed with "ip ".

The intent of this patch is to later add something like
  #define pr_fmt(fmt) "IPv4: " fmt.
to standardize the output messages.

Text size is trivially reduced. (x86-32 allyesconfig)

$ size net/ipv4/built-in.o*
   text	   data	    bss	    dec	    hex	filename
 887888	  31558	 249696	1169142	 11d6f6	net/ipv4/built-in.o.new
 887934	  31558	 249800	1169292	 11d78c	net/ipv4/built-in.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-11 23:42:51 -07:00
Maciej Żenczykowski 43db362d3a net: get rid of some pointless casts to sockaddr
The following 4 functions:
  move_addr_to_kernel
  move_addr_to_user
  verify_iovec
  verify_compat_iovec
are always effectively called with a sockaddr_storage.

Make this explicit by changing their signature.

This removes a large number of casts from sockaddr_storage to sockaddr.

Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-11 19:11:22 -07:00
Trond Myklebust 09acfea5d8 SUNRPC: Fix a few sparse warnings
net/sunrpc/svcsock.c:412:22: warning: incorrect type in assignment
(different address spaces)
 - svc_partial_recvfrom now takes a struct kvec, so the variable
   save_iovbase needs to be an ordinary (void *)

Make a bunch of variables in net/sunrpc/xprtsock.c static

Fix a couple of "warning: symbol 'foo' was not declared. Should it be
static?" reports.

Fix a couple of conflicting function declarations.

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2012-03-11 19:30:02 -04:00
Li Wei 8b2aaedee4 ipv6: Fix Smatch warning.
With commit d6ddef9e641d(IPv6: Fix not join all-router mcast group
when forwarding set.) I check 'dev' after it's dereference that
leads to a Smatch complaint:

net/ipv6/addrconf.c:438 ipv6_add_dev()
	 warn: variable dereferenced before check 'dev' (see line 432)

net/ipv6/addrconf.c
   431		/* protected by rtnl_lock */
   432		rcu_assign_pointer(dev->ip6_ptr, ndev);
                                   ^^^^^^^^^^^^
Old dereference.

   433
   434		/* Join all-node multicast group */
   435		ipv6_dev_mc_inc(dev, &in6addr_linklocal_allnodes);
   436
   437		/* Join all-router multicast group if forwarding is set
*/
   438		if (ndev->cnf.forwarding && dev && (dev->flags &
IFF_MULTICAST))
                                            ^^^

Remove the check to avoid the complaint as 'dev' can't be NULL.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-11 15:57:11 -07:00
Eric Dumazet dfd25ffffc tcp: fix syncookie regression
commit ea4fc0d619 (ipv4: Don't use rt->rt_{src,dst} in ip_queue_xmit())
added a serious regression on synflood handling.

Simon Kirby discovered a successful connection was delayed by 20 seconds
before being responsive.

In my tests, I discovered that xmit frames were lost, and needed ~4
retransmits and a socket dst rebuild before being really sent.

In case of syncookie initiated connection, we use a different path to
initialize the socket dst, and inet->cork.fl.u.ip4 is left cleared.

As ip_queue_xmit() now depends on inet flow being setup, fix this by
copying the temp flowi4 we use in cookie_v4_check().

Reported-by: Simon Kirby <sim@netnation.com>
Bisected-by: Simon Kirby <sim@netnation.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-11 15:52:12 -07:00
sjur.brandeland@stericsson.com e3abcc2a85 caif: make zero a legal caif connetion id.
Connection ID configured through RTNL must allow zero as
connection id. If connection-id is not given when creating the
interface, configure a loopback interface using ifindex as
connection-id.

Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-11 15:38:16 -07:00
Dmitry Tarnyagin 374458b3fe caif: Fix for a race in socket transmit with flow control.
Kill faulty checks on flow-off leading to connection drop at race conditions.
caif_socket checks for flow-on before transmitting and goes to sleep or
return -EAGAIN upon flow stop. Remove faulty subsequent checks on flow-off
leading to connection drop. Also fix memory leaks on some of the errors paths.

Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-11 15:38:16 -07:00
David S. Miller e8abbe0d02 Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge 2012-03-11 15:36:34 -07:00
Paul Gortmaker 51990e8254 device.h: cleanup users outside of linux/include (C files)
For files that are actively using linux/device.h, make sure
that they call it out.  This will allow us to clean up some
of the implicit uses of linux/device.h within include/*
without introducing build regressions.

Yes, this was created by "cheating" -- i.e. the headers were
cleaned up, and then the fallout was found and fixed, and then
the two commits were reordered.  This ensures we don't introduce
build regressions into the git history.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2012-03-11 14:27:37 -04:00
Heiko Carstens fde15c3a3a [S390] irq: external interrupt code passing
The external interrupt handlers have a parameter called ext_int_code.
Besides the name this paramter does not only contain the ext_int_code
but in addition also the "cpu address" (POP) which caused the external
interrupt.
To make the code a bit more obvious pass a struct instead so the called
function can easily distinguish between external interrupt code and
cpu address. The cpu address field however is named "subcode" since
some external interrupt sources do not pass a cpu address but a
different parameter (or none at all).

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2012-03-11 11:59:29 -04:00
Sven Eckelmann 40e0c4f51d batman-adv: Remove spaces after a cast
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
2012-03-11 06:29:44 +08:00
Sven Eckelmann 96741ade15 batman-adv: Use {} braces consistent on the arms of a statement
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
2012-03-11 06:29:44 +08:00
Sven Eckelmann 21a1236bc3 batman-adv: Don't begin block comments with only a /* line
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
2012-03-11 06:29:44 +08:00
Sven Eckelmann 86ceb36056 batman-adv: Ignore 80-chars per line limits for strings
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
2012-03-11 06:29:44 +08:00
David S. Miller 6a91395f20 ipv4: Make ip_rcv_options() return bool.
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-09 14:34:50 -08:00
David S. Miller ba57b4db26 ipv4: Make ip_call_ra_chain() return bool.
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-09 14:34:50 -08:00
David S. Miller b2d3298e09 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2012-03-09 14:34:20 -08:00
John W. Linville 74dd1521d0 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem 2012-03-09 14:57:30 -05:00
Benjamin Poirier 0343c5543b sctp: Export sctp_do_peeloff
lookup sctp_association within sctp_do_peeloff() to enable its use outside of
the sctp code with minimal knowledge of the former.

Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-08 13:52:08 -08:00
Jiri Slaby 410235fd4d TTY: remove unneeded tty->index checks
Checking if tty->index is in bounds is not needed. The tty has the
index set in the initial open. This is done in get_tty_driver. And it
can be only in interval <0,driver->num).

So remove the tests which check exactly this interval. Some are
left untouched as they check against the current backing device count.
(Leaving apart that the check is racy in most of the cases.)

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-08 11:42:21 -08:00
Jiri Slaby 2f16669d32 TTY: remove re-assignments to tty_driver members
All num, magic and owner are set by alloc_tty_driver. No need to
re-set them on each allocation site.

pti driver sets something different to what it passes to
alloc_tty_driver. It is not a bug, since we don't use the lines
parameter in any way. Anyway this is fixed, and now we do the right
thing.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-08 11:37:58 -08:00
Steffen Klassert ac3f48de09 route: Remove redirect_genid
As we invalidate the inetpeer tree along with the routing cache now,
we don't need a genid to reset the redirect handling when the routing
cache is flushed.

Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-08 00:30:32 -08:00
Steffen Klassert 5faa5df1fa inetpeer: Invalidate the inetpeer tree along with the routing cache
We initialize the routing metrics with the values cached on the
inetpeer in rt_init_metrics(). So if we have the metrics cached on the
inetpeer, we ignore the user configured fib_metrics.

To fix this issue, we replace the old tree with a fresh initialized
inet_peer_base. The old tree is removed later with a delayed work queue.

Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-08 00:30:24 -08:00
Paulius Zaleckas 5200959b83 bridge: fix state reporting when port is disabled
Now we have:
eth0: link *down*
br0: port 1(eth0) entered *forwarding* state

br_log_state(p) should be called *after* p->state is set
to BR_STATE_DISABLED.

Reported-by: Zilvinas Valinskas <zilvinas@wilibox.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-08 00:25:25 -08:00
Paulius Zaleckas d9e179ecec bridge: br_log_state() s/entering/entered/
When br_log_state() is reporting state it should say "entered"
istead of "entering" since state at this point is already
changed.

Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-08 00:25:25 -08:00
David S. Miller 0111ad823e Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/padovan/bluetooth-next 2012-03-07 22:53:48 -08:00
Ursula Braun 82492a355f af_iucv: add shutdown for HS transport
AF_IUCV sockets offer a shutdown function. This patch makes sure
shutdown works for HS transport as well.

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-07 22:52:24 -08:00
Ursula Braun 9fbd87d413 af_iucv: handle netdev events
In case of transport through HiperSockets the underlying network
interface may switch to DOWN state or the underlying network device
may recover. In both cases the socket must change to IUCV_DISCONN
state. If the interface goes down, af_iucv has a chance to notify
its connection peer in addition.

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-07 22:52:24 -08:00
David S. Miller 9259c483a3 Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jesse/openvswitch 2012-03-07 22:49:01 -08:00
David S. Miller c75a312d8b Merge branch 'master' of git://1984.lsi.us.es/net-next 2012-03-07 22:27:56 -08:00
Ido Yariv fdde0a26a2 Bluetooth: Set security level on incoming pairing request
If a master would like to raise the security level, it will send a
pairing request. While the pending security level is set on an incoming
security request (from a slave), it is not set on a pairing request. As
a result, the security level would not be raised on the slave in such
case.

Fix this by setting the pending security when receiving pairing
requests according to the requested authorization.

Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2012-03-08 02:26:04 -03:00
Ido Yariv b3ff53ff00 Bluetooth: Fix access to the STK generation methods matrix
The major index of the table is actually the remote I/O capabilities, not
the local ones. As a result, devices with different I/O capabilities
could have used wrong or even unsupported generation methods.

Signed-off-by: Ido Yariv <ido@wizery.com>
CC: Brian Gix <bgix@codeaurora.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2012-03-08 02:25:00 -03:00
Luiz Augusto von Dentz e57d758ae8 Bluetooth: Fix using uninitialized variable
+ src/net/bluetooth/rfcomm/tty.c: warning: 'p' is used uninitialized in this
       function:  => 218
+ src/net/bluetooth/rfcomm/tty.c: warning: 'p' may be used uninitialized in
       this function:  => 218

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2012-03-08 02:20:22 -03:00
Gustavo F. Padovan 04124681f1 Bluetooth: fix conding style issues all over the tree
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2012-03-08 02:02:26 -03:00
Jesse Gross 81e5d41d7e openvswitch: Fix checksum update for actions on UDP packets.
When modifying IP addresses or ports on a UDP packet we don't
correctly follow the rules for unchecksummed packets.  This meant
that packets without a checksum can be given a incorrect new checksum
and packets with a checksum can become marked as being unchecksummed.
This fixes it to handle those requirements.

Signed-off-by: Jesse Gross <jesse@nicira.com>
2012-03-07 14:36:57 -08:00
Eric Dumazet b4fb05ea40 tcp: md5: correct a RCU lockdep splat
commit a8afca0329 (tcp: md5: protects md5sig_info with RCU) added a
lockdep splat in tcp_md5_do_lookup() in case a timer fires a tcp
retransmit.

At this point, socket lock is owned by the sofirq handler, not the user,
so we should adjust a bit the lockdep condition, as we dont hold
rcu_read_lock().

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-07 15:13:42 -05:00
Thomas Pedersen f06c7885c3 mac80211: fix smatch lock errors in mesh
smatch was complaining:

CHECK   net/mac80211/mesh_pathtbl.c
net/mac80211/mesh_pathtbl.c:562 mesh_path_add() error: double lock
'bottom_half:'
net/mac80211/mesh_pathtbl.c:580 mesh_path_add() error: double unlock
'bottom_half:'
net/mac80211/mesh_pathtbl.c:589 mesh_path_add() error: double unlock
'bottom_half:'
net/mac80211/mesh_pathtbl.c:691 mpp_path_add() error: double lock
'bottom_half:'
net/mac80211/mesh_pathtbl.c:707 mpp_path_add() error: double unlock
'bottom_half:'
net/mac80211/mesh_pathtbl.c:716 mpp_path_add() error: double unlock
'bottom_half:'
net/mac80211/mesh_pathtbl.c:814 mesh_path_flush_by_nexthop() error:
double lock 'bottom_half:'
net/mac80211/mesh_pathtbl.c:819 mesh_path_flush_by_nexthop() error:
double unlock 'bottom_half:'
net/mac80211/mesh_pathtbl.c:887 mesh_path_del() error: double lock
'bottom_half:'
net/mac80211/mesh_pathtbl.c:901 mesh_path_del() error: double unlock
'bottom_half:'

So don't lock / unlock with _bh() while bottom halves are already
disabled.

Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-07 13:56:36 -05:00
Ashok Nagarajan 3d4f969972 mac80211: Fix potential null pointer dereferencing
The patch "{nl,cfg,mac}80211: Implement RSSI threshold for mesh peering"
has a potential null pointer dereferencing problem. Thanks to Dan Carpenter
for pointing out. This patch will fix the issue.

Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-07 13:51:47 -05:00
Paul Stewart fcff4f108d mac80211: Filter duplicate IE ids
mac80211 is lenient with respect to reception of corrupted beacons.
Even if the frame is corrupted as a whole, the available IE elements
are still passed back and accepted, sometimes replacing legitimate
data.  It is unknown to what extent this "feature" is made use of,
but it is clear that in some cases, this is detrimental.  One such
case is reported in http://crosbug.com/26832 where an AP corrupts
its beacons but not its probe responses.

One approach would be to completely reject frames with invaid data
(for example, if the last tag extends beyond the end of the enclosing
PDU).  The enclosed approach is much more conservative: we simply
prevent later IEs from overwriting the state from previous ones.
This approach hopes that there might be some salient data in the
IE stream before the corruption, and seeks to at least prevent that
data from being overwritten.  This approach will fix the case above.

Further, we flag element structures that contain data we think might
be corrupted, so that as we fill the mac80211 BSS structure, we try
not to replace data from an un-corrupted probe response with that
of a corrupted beacon, for example.

Short of any statistics gathering in the various forms of AP breakage,
it's not possible to ascertain the side effects of more stringent
discarding of data.

Signed-off-by: Paul Stewart <pstew@chromium.org>
Cc: Sam Leffler <sleffler@chromium.org>
Cc: Eliad Peller <eliad@wizery.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-07 13:51:37 -05:00
Pablo Neira Ayuso 24de58f465 netfilter: xt_CT: allow to attach timeout policy + glue code
This patch allows you to attach the timeout policy via the
CT target, it adds a new revision of the target to ensure
backward compatibility. Moreover, it also contains the glue
code to stick the timeout object defined via nfnetlink_cttimeout
to the given flow.

Example usage (it requires installing the nfct tool and
libnetfilter_cttimeout):

1) create the timeout policy:

 nfct timeout add tcp-policy0 inet tcp \
	established 1000 close 10 time_wait 10 last_ack 10

2) attach the timeout policy to the packet:

 iptables -I PREROUTING -t raw -p tcp -j CT --timeout tcp-policy0

You have to install the following user-space software:

a) libnetfilter_cttimeout:
   git://git.netfilter.org/libnetfilter_cttimeout

b) nfct:
   git://git.netfilter.org/nfct

You also have to get iptables with -j CT --timeout support.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:41:28 +01:00
Pablo Neira Ayuso dd70507241 netfilter: nf_ct_ext: add timeout extension
This patch adds the timeout extension, which allows you to attach
specific timeout policies to flows.

This extension is only used by the template conntrack.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:41:25 +01:00
Pablo Neira Ayuso 5097846230 netfilter: add cttimeout infrastructure for fine timeout tuning
This patch adds the infrastructure to add fine timeout tuning
over nfnetlink. Now you can use the NFNL_SUBSYS_CTNETLINK_TIMEOUT
subsystem to create/delete/dump timeout objects that contain some
specific timeout policy for one flow.

The follow up patches will allow you attach timeout policy object
to conntrack via the CT target and the conntrack extension
infrastructure.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:41:22 +01:00
Pablo Neira Ayuso 2c8503f55f netfilter: nf_conntrack: pass timeout array to l4->new and l4->packet
This patch defines a new interface for l4 protocol trackers:

unsigned int *(*get_timeouts)(struct net *net);

that is used to return the array of unsigned int that contains
the timeouts that will be applied for this flow. This is passed
to the l4proto->new(...) and l4proto->packet(...) functions to
specify the timeout policy.

This interface allows per-net global timeout configuration
(although only DCCP supports this by now) and it will allow
custom custom timeout configuration by means of follow-up
patches.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:41:19 +01:00
Pablo Neira Ayuso b888341c7f netfilter: nf_ct_gre: add unsigned int array to define timeouts
This patch adds an array to define the default GRE timeouts.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:41:16 +01:00
Pablo Neira Ayuso 33ee44643f netfilter: nf_ct_tcp: move retransmission and unacknowledged timeout to array
This patch moves the retransmission and unacknowledged timeouts
to the tcp_timeouts array. This change is required by follow-up
patches.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:41:15 +01:00
Pablo Neira Ayuso 5a41db94c6 netfilter: nf_ct_udp[lite]: convert UDP[lite] timeouts to array
Use one array to store the UDP timeouts instead of two variables.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:41:13 +01:00
Hans Schillstrom 3b988ece9b netfilter: ctnetlink: fix lockep splats
net/netfilter/nf_conntrack_proto.c:70 suspicious rcu_dereference_check() usage!

other info that might help us debug this:

rcu_scheduler_active = 1, debug_locks = 0
3 locks held by conntrack/3235:
nfnl_lock+0x17/0x20
netlink_dump+0x32/0x240
ctnetlink_dump_table+0x3e/0x170 [nf_conntrack_netlink]

stack backtrace:
Pid: 3235, comm: conntrack Tainted: G W  3.2.0+ #511
Call Trace:
[<ffffffff8108ce45>] lockdep_rcu_suspicious+0xe5/0x100
[<ffffffffa00ec6e1>] __nf_ct_l4proto_find+0x81/0xb0 [nf_conntrack]
[<ffffffffa0115675>] ctnetlink_fill_info+0x215/0x5f0 [nf_conntrack_netlink]
[<ffffffffa0115dc1>] ctnetlink_dump_table+0xd1/0x170 [nf_conntrack_netlink]
[<ffffffff815fbdbf>] netlink_dump+0x7f/0x240
[<ffffffff81090f9d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff815fd34f>] netlink_dump_start+0xdf/0x190
[<ffffffffa0111490>] ? ctnetlink_change_nat_seq_adj+0x160/0x160 [nf_conntrack_netlink]
[<ffffffffa0115cf0>] ? ctnetlink_get_conntrack+0x2a0/0x2a0 [nf_conntrack_netlink]
[<ffffffffa0115ad9>] ctnetlink_get_conntrack+0x89/0x2a0 [nf_conntrack_netlink]
[<ffffffff81603a47>] nfnetlink_rcv_msg+0x467/0x5f0
[<ffffffff81603a7c>] ? nfnetlink_rcv_msg+0x49c/0x5f0
[<ffffffff81603922>] ? nfnetlink_rcv_msg+0x342/0x5f0
[<ffffffff81071b21>] ? get_parent_ip+0x11/0x50
[<ffffffff816035e0>] ? nfnetlink_subsys_register+0x60/0x60
[<ffffffff815fed49>] netlink_rcv_skb+0xa9/0xd0
[<ffffffff81603475>] nfnetlink_rcv+0x15/0x20
[<ffffffff815fe70e>] netlink_unicast+0x1ae/0x1f0
[<ffffffff815fea16>] netlink_sendmsg+0x2c6/0x320
[<ffffffff815b2a87>] sock_sendmsg+0x117/0x130
[<ffffffff81125093>] ? might_fault+0x53/0xb0
[<ffffffff811250dc>] ? might_fault+0x9c/0xb0
[<ffffffff81125093>] ? might_fault+0x53/0xb0
[<ffffffff815b5991>] ? move_addr_to_kernel+0x71/0x80
[<ffffffff815b644e>] sys_sendto+0xfe/0x130
[<ffffffff815b5c94>] ? sys_bind+0xb4/0xd0
[<ffffffff817a8a0e>] ? retint_swapgs+0xe/0x13
[<ffffffff817afcd2>] system_call_fastpath+0x16/0x1b

Reported-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
2012-03-07 17:41:10 +01:00
Richard Weinberger 417e02bf42 netfilter: xt_LOG: fix bogus extra layer-4 logging information
In 16059b5 netfilter: merge ipt_LOG and ip6_LOG into xt_LOG, we have
merged ipt_LOG and ip6t_LOG.

However:

IN=wlan0 OUT= MAC=xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx
SRC=213.150.61.61 DST=192.168.1.133 LEN=40 TOS=0x00 PREC=0x00 TTL=117
ID=10539 DF PROTO=TCP SPT=80 DPT=49013 WINDOW=0 RES=0x00 ACK RST
URGP=0 PROTO=UDPLITE SPT=80 DPT=49013 LEN=45843 PROTO=ICMP TYPE=0
       ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

Several missing break in the code led to including bogus layer-4
information. This patch fixes this problem.

Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:40:59 +01:00
Tony Zelenoff 58020f7761 netfilter: nf_ct_ecache: refactor nf_ct_deliver_cached_events
* identation lowered
* some CPU cycles saved at delayed item variable initialization

Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:40:53 +01:00
Tony Zelenoff 93326ae312 netfilter: nf_ct_ecache: trailing whitespace removed
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:40:51 +01:00
Richard Weinberger 6939c33a75 netfilter: merge ipt_LOG and ip6_LOG into xt_LOG
ipt_LOG and ip6_LOG have a lot of common code, merge them
to reduce duplicate code.

Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:40:49 +01:00
Pablo Neira Ayuso 544d5c7d9f netfilter: ctnetlink: allow to set expectfn for expectations
This patch allows you to set expectfn which is specifically used
by the NAT side of most of the existing conntrack helpers.

I have added a symbol map that uses a string as key to look up for
the function that is attached to the expectation object. This is
the best solution I came out with to solve this issue.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:40:46 +01:00
Pablo Neira Ayuso 076a0ca026 netfilter: ctnetlink: add NAT support for expectations
This patch adds the missing bits to create expectations that
are created in NAT setups.
2012-03-07 17:40:44 +01:00
Pablo Neira Ayuso b8c5e52c13 netfilter: ctnetlink: allow to set expectation class
This patch allows you to set the expectation class.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:40:42 +01:00
Pablo Neira Ayuso 660fdb2a0f netfilter: ctnetlink: allow to set helper for new expectations
This patch allow you to set the helper for newly created
expectations based of the CTA_EXPECT_HELP_NAME attribute.
Before this, the helper set was NULL.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:40:40 +01:00
Jozsef Kadlecsik 2a7cef2a4b netfilter: ipset: Exceptions support added to hash:*net* types
The "nomatch" keyword and option is added to the hash:*net* types,
by which one can add exception entries to sets. Example:

        ipset create test hash:net
        ipset add test 192.168.0/24
        ipset add test 192.168.0/30 nomatch

In this case the IP addresses from 192.168.0/24 except 192.168.0/30
match the elements of the set.

Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:40:35 +01:00
Jan Engelhardt c15f1c8325 netfilter: ipset: use NFPROTO_ constants
ipset is actually using NFPROTO values rather than AF (xt_set passes
that along).

Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-03-07 17:40:29 +01:00
Ben Pfaff 651a68ea2c openvswitch: Honor dp_ifindex, when specified, for vport lookup by name.
When OVS_VPORT_ATTR_NAME is specified and dp_ifindex is nonzero, the
logical behavior would be for the vport name lookup scope to be limited
to the specified datapath, but in fact the dp_ifindex value was ignored.
This commit causes the search scope to be honored.

Signed-off-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
2012-03-06 15:04:04 -08:00
Li Wei d6ddef9e64 IPv6: Fix not join all-router mcast group when forwarding set.
When forwarding was set and a new net device is register,
we need add this device to the all-router mcast group.

Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-06 16:58:47 -05:00
David S. Miller 95f050bf7f net: Use bool for return value of dev_valid_name().
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-06 16:12:15 -05:00
Samuel Ortiz eb9bc6e9a0 NFC: NCI code identation fixes
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:25 -05:00
Samuel Ortiz 0a40acb246 NFC: Core code identation fixes
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:25 -05:00
Samuel Ortiz 427a2eb1f5 NFC: LLCP code identation fixes
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:24 -05:00
Samuel Ortiz 40c75f81d6 NFC: Fix LLCP sockets releasing path
The socket local pointer needs to be set to NULL when the adapter is
removed or the MAC goes down.
If the socket release code is called after such an event, the socket
reference count still needs to be decreased in order for the socket to
eventually be freed.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:24 -05:00
Samuel Ortiz 47807d3dbb NFC: Remove the rf mode parameter from the DEP link up routine
When calling nfc_dep_link_up, we implicitely are in initiator mode.
Which means we also can provide the general bytes as a function argument,
as all drivers will eventually request them.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:23 -05:00
Samuel Ortiz 9dda50f4c9 NFC: SN is not an invalid GT value
We just don't do anything with it when parsing the general bytes.
We handle it from the CONNECT reception code.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:23 -05:00
Samuel Ortiz 0c31835993 NFC: Unlink LLCP child sockets from llcp_sock_release
The parent socket (the bound one) could be freed before its children, so
we should unlink the children without trying to reach it through the parent.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:23 -05:00
Samuel Ortiz e65b0f46ed NFC: Fragment LLCP I frames
Based on the receiver MIU, we have to fragment the frame to be
transmitted.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:22 -05:00
Samuel Ortiz eda21f16a5 NFC: Set MIU and RW values from CONNECT and CC LLCP frames
We use the maximum values for the LLCP Maximum Information Unit and Receive
Window Size.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:22 -05:00
Samuel Ortiz d094afa155 NFC: Send LLCP RR frames to acknowledge received I frames
In order to acknowledge an I frame, we have to either queue pending local
I frames or queue a receiver ready frame.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:22 -05:00
Samuel Ortiz 0767a7fa87 NFC: Set the right LLCP N(R) value for I frames
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:21 -05:00
Samuel Ortiz b9a76f1d3c NFC: Clear LLCP SDPs whan MAC goes down
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:21 -05:00
Samuel Ortiz 1762c17c9c NFC: Fix bitops usage in LLCP
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:20 -05:00
Samuel Ortiz 53a0ac2ee8 NFC: LLCP socket sendmsg implemetation
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:20 -05:00
Samuel Ortiz 53aef92054 NFC: Handle Receiver Not Ready LLCP frame
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:20 -05:00
Samuel Ortiz 4722d2b70b NFC: Factorize the I frame queueing routine
This one will be called from the I frame command sending.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:19 -05:00
Samuel Ortiz c970a1ac4e NFC: Add device powered netlink attribute
For user space to know if a device is up or down.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:19 -05:00
Javier Cardona 12ce8ba3eb mac80211: Modify tsf via debugfs in mesh interfaces
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:17 -05:00
Thomas Pedersen 6b62bf3263 mac80211: fix mesh airtime link metric estimating
Airtime link metric estimation was broken in HT mesh, use
cfg80211_calculate_bitrate to get the right rate value.

Also factor out tx rate copying from sta_set_sinfo().

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:17 -05:00
Thomas Pedersen 8097e14944 cfg80211: expose cfg80211_calculate_bitrate()
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:17 -05:00
Johannes Berg 804483e907 cfg80211/mac80211: report signal strength for mgmt frames
Add the signal strength (in dBm only for now) to
frames that are received via nl80211's various
frame APIs.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06 15:16:05 -05:00
Pablo Neira Ayuso 7413851197 netfilter: nf_conntrack: fix early_drop with reliable event delivery
If reliable event delivery is enabled and ctnetlink fails to deliver
the destroy event in early_drop, the conntrack subsystem cannot
drop any the candidate flow that was planned to be evicted.

Reported-by: Kerin Millar <kerframil@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-06 14:43:50 -05:00
Florian Westphal 739e4505a0 bridge: netfilter: don't call iptables on vlan packets if sysctl is off
When net.bridge.bridge-nf-filter-vlan-tagged is 0 (default), vlan packets
arriving should not be sent to ip(6)tables by bridge netfilter.

However, it turns out that we currently always send VLAN packets to
netfilter, if ..
a), CONFIG_VLAN_8021Q is enabled ; or
b), CONFIG_VLAN_8021Q is not set but rx vlan offload is enabled
   on the bridge port.

This is because bridge netfilter treats skb with
skb->protocol == ETH_P_IP{V6} as "non-vlan packet".

With rx vlan offload on or CONFIG_VLAN_8021Q=y, the vlan header has
already been removed here, and we cannot rely on skb->protocol alone.

Fix this by only using skb->protocol if the skb has no vlan tag,
or if a vlan tag is present and filter-vlan-tagged bridge netfilter
sysctl is enabled.

We cannot remove the skb->protocol == htons(ETH_P_8021Q) test
because the vlan tag is still around in the CONFIG_VLAN_8021Q=n &&
"ethtool -K $itf rxvlan off" case.

reproducer:
iptables -t raw -I PREROUTING -i br0
iptables -t raw -I PREROUTING -i br0.1

Then send packets to an ip address configured on br0.1 interface.
Even with net.bridge.bridge-nf-filter-vlan-tagged=0, the 1st rule
will match instead of the 2nd one.

With this patch applied, the 2nd rule will match instead.
In the non-local address case, netfilter won't be consulted after
this patch unless the sysctl is switched on.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-06 14:43:49 -05:00
Pablo Neira Ayuso a157b9d5b5 netfilter: bridge: fix wrong pointer dereference
In adf7ff8, a invalid dereference was added in ebt_make_names.

CC [M]  net/bridge/netfilter/ebtables.o
net/bridge/netfilter/ebtables.c: In function `ebt_make_names':
net/bridge/netfilter/ebtables.c:1371:20: warning: `t' may be used uninitialized in this function [-Wuninitialized]

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-06 14:43:49 -05:00
Pablo Neira Ayuso 8be619d1e4 netfilter: ctnetlink: remove incorrect spin_[un]lock_bh on NAT module autoload
Since 7d367e0, ctnetlink_new_conntrack is called without holding
the nf_conntrack_lock spinlock. Thus, ctnetlink_parse_nat_setup
does not require to release that spinlock anymore in the NAT module
autoload case.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-06 14:43:49 -05:00
Santosh Nayak 848edc6919 netfilter: ebtables: fix wrong name length while copying to user-space
user-space ebtables expects 32 bytes-long names, but xt_match names
use 29 bytes. We have to copy less 29 bytes and then, make sure we
fill the remaining bytes with zeroes.

Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-06 14:43:49 -05:00
Neal Cardwell 4648dc97af tcp: fix tcp_shift_skb_data() to not shift SACKed data below snd_una
This commit fixes tcp_shift_skb_data() so that it does not shift
SACKed data below snd_una.

This fixes an issue whose symptoms exactly match reports showing
tp->sacked_out going negative since 3.3.0-rc4 (see "WARNING: at
net/ipv4/tcp_input.c:3418" thread on netdev).

Since 2008 (832d11c5cd)
tcp_shift_skb_data() had been shifting SACKed ranges that were below
snd_una. It checked that the *end* of the skb it was about to shift
from was above snd_una, but did not check that the end of the actual
shifted range was above snd_una; this commit adds that check.

Shifting SACKed ranges below snd_una is problematic because for such
ranges tcp_sacktag_one() short-circuits: it does not declare anything
as SACKed and does not increase sacked_out.

Before the fixes in commits cc9a672ee5
and daef52bab1, shifting SACKed ranges
below snd_una happened to work because tcp_shifted_skb() was always
(incorrectly) passing in to tcp_sacktag_one() an skb whose end_seq
tcp_shift_skb_data() had already guaranteed was beyond snd_una. Hence
tcp_sacktag_one() never short-circuited and always increased
tp->sacked_out in this case.

After those two fixes, my testing has verified that shifting SACKed
ranges below snd_una could cause tp->sacked_out to go negative with
the following sequence of events:

(1) tcp_shift_skb_data() sees an skb whose end_seq is beyond snd_una,
    then shifts a prefix of that skb that is below snd_una

(2) tcp_shifted_skb() increments the packet count of the
    already-SACKed prev sk_buff

(3) tcp_sacktag_one() sees the end of the new SACKed range is below
    snd_una, so it short-circuits and doesn't increase tp->sacked_out

(5) tcp_clean_rtx_queue() sees the SACKed skb has been ACKed,
    decrements tp->sacked_out by this "inflated" pcount that was
    missing a matching increase in tp->sacked_out, and hence
    tp->sacked_out underflows to a u32 like 0xFFFFFFFF, which casted
    to s32 is negative.

(6) this leads to the warnings seen in the recent "WARNING: at
    net/ipv4/tcp_input.c:3418" thread on the netdev list; e.g.:
    tcp_input.c:3418  WARN_ON((int)tp->sacked_out < 0);

More generally, I think this bug can be tickled in some cases where
two or more ACKs from the receiver are lost and then a DSACK arrives
that is immediately above an existing SACKed skb in the write queue.

This fix changes tcp_shift_skb_data() to abort this sequence at step
(1) in the scenario above by noticing that the bytes are below snd_una
and not shifting them.

Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-06 14:43:49 -05:00
David S. Miller f6a1ad4295 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/vmxnet3/vmxnet3_drv.c

Small vmxnet3 conflict with header size bug fix in 'net'.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-05 21:16:26 -05:00
Ulrich Weber d1d81d4c3d bridge: check return value of ipv6_dev_get_saddr()
otherwise source IPv6 address of ICMPV6_MGM_QUERY packet
might be random junk if IPv6 is disabled on interface or
link-local address is not yet ready (DAD).

Signed-off-by: Ulrich Weber <ulrich.weber@sophos.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-05 16:45:34 -05:00
David S. Miller 7c1e51a34a Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next 2012-03-05 16:39:02 -05:00
Johannes Berg 3abead59fc mac80211: combine QoS with other BSS changes
When associating and particularly when disassociating
there's no need to notify the driver about changes
with multiple calls to bss_info_changed, we should
combine the QoS enabling/disabling into the same call
as otherwise the driver could get confused about QoS
suddenly getting disabled while connected.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:53:46 -05:00
Johannes Berg 293702a3fb mac80211: use common radiotap code for cooked monitors
There's no need to hardcode a subset of the
radiotap header for cooked monitor receive,
we can just reuse the normal monitor mode
radiotap code. This simplifies the code and
extends the information available on cooked
monitor interfaces.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:38:35 -05:00
Vasanthakumar Thiagarajan 1b658f118b cfg80211: Add an attribute to set inactivity timeout in AP mode
This patch adds an attribute, NL80211_ATTR_INACTIVITY_TIMEOUT,
to set the inactivity timeout which can be used to remove the
station in AP mode. This can be passed in NL80211_CMD_START_AP
and used by the drivers which have AP MLME in firmware but
don't support get_station() properly. To disable inactivity
timer in userspace, wpa_s for example, there is a new flag,
NL80211_FEATURE_INACTIVITY_TIMER, in nl80211_feature_flags
through which drivers can register their capability to use
the inactivity timeout to free the stations.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:38:34 -05:00
Chun-Yeow Yeoh d665508b98 mac80211: fix the support of setting non-forwarding entity in Mesh
RANN, PREP and PERR propagation should happen only if the
dot11MeshForwarding is true.  Besides, data frame should not be
forwarded if dot11MeshForwarding is false. This redundant checking
is necessary to avoid the broadcasted ARP breaking the non-forwarding
rule.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:38:33 -05:00
Eric Dumazet 77a1abf54f net: export netdev_stats_to_stats64
Some drivers use internal netdev stats member to store part of their
stats, yet advertize ndo_get_stats64() to implement some 64bit fields.

Allow them to use netdev_stats_to_stats64() helper to make the copy of
netdev stats before they compute their 64bit counters.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-05 15:38:32 -05:00
Felix Fietkau fe8431f89e mac80211: add an rx flag for ignoring a packet's signal strength
For A-MPDU rx it makes sense to only process the signal strength once per
aggregate instead of once per subframe. Additonally, some hardware (e.g.
Atheros) only provides valid signal strength information for the last
subframe.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:38:32 -05:00
Felix Fietkau 888d04dfbe mac80211: use compare_ether_addr on MAC addresses instead of memcmp
Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:38:31 -05:00
Felix Fietkau 4d196e4b2f mac80211: use 16 bit alignment for the if_ibss bssid field
Several MAC address comparison functions assume 16 bit alignment for pointers
passed to them. Since the addition of the control_port field, alignment
for the IBSS bssid was off by one, causing a severe performance hit on
architectures without efficient unaligned access (e.g. MIPS).

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:24:14 -05:00
Ashok Nagarajan 5533513784 {nl,cfg,mac}80211: Implement RSSI threshold for mesh peering
Mesh peer links are established only if average rssi of the peer
candidate satisfies the threshold. This is not in 802.11s specification
but was requested by David Fulgham, an open80211s user. This is a way to avoid
marginal peer links with stations that are barely within range.

This patch adds a new mesh configuration parameter, mesh_rssi_threshold. This
feature is supported only for hardwares that report signal in dBm.

Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:23:15 -05:00
Chun-Yeow Yeoh 3d045a5448 mac80211: Fix the generation of PREQs in proactive RANN mechanism of HWMP
According to Section Y.7.4 Actions on receipt of proactive RANN, an individually
addressed PREQ should be generated towards the neighbor peer mesh STA indicated
in the RANN Sender Address field in the forwarding information.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-05 15:23:14 -05:00
John W. Linville 051d3b5043 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem 2012-03-05 15:05:54 -05:00
Ingo Molnar 737f24bda7 Merge branch 'perf/urgent' into perf/core
Conflicts:
	tools/perf/builtin-record.c
	tools/perf/builtin-top.c
	tools/perf/perf.h
	tools/perf/util/top.h

Merge reason: resolve these cherry-picking conflicts.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2012-03-05 09:20:08 +01:00
Eric Dumazet a4b64fbe48 rtnetlink: fix rtnl_calcit() and rtnl_dump_ifinfo()
nlmsg_parse() might return an error, so test its return value before
potential random memory accesses.

Errors introduced in commit 115c9b8192 (rtnetlink: Fix problem with
buffer allocation)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-04 22:02:55 -05:00
Joakim Tjernlund 709e1b5cd9 bridge: message age needs to increase, not decrease.
commit bridge: send proper message_age in config BPDU
added this gem:
  bpdu.message_age = (jiffies - root->designated_age)
  p->designated_age = jiffies + bpdu->message_age;
Notice how bpdu->message_age is negated when reassigned to
bpdu.message_age. This causes message age to decrease breaking the
STP protocol.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-04 21:57:40 -05:00
Joakim Tjernlund aaca735f4f bridge: Adjust min age inc for HZ > 256
min age increment needs to round up its min age tick for all
HZ values to guarantee message age is increasing.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-04 21:57:39 -05:00
Paul Mackerras 4b32da2bcf ppp: Replace uses of <linux/if_ppp.h> with <linux/ppp-ioctl.h>
Since all that include/linux/if_ppp.h does is #include <linux/ppp-ioctl.h>,
this replaces the occurrences of #include <linux/if_ppp.h> with
#include <linux/ppp-ioctl.h>.

It also corrects an error in Documentation/networking/l2tp.txt, where
it referenced include/linux/if_ppp.h as the source of some definitions
that are actually now defined in include/linux/if_pppol2tp.h.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-04 20:41:38 -05:00
Trond Myklebust 8aa0a410af Merge commit 'nfs-for-3.3-4' into nfs-for-next
Conflicts:
	fs/nfs/nfs4proc.c

Back-merge of the upstream kernel in order to fix a conflict with the
slotid type conversion and implementation id patches...
2012-03-03 15:05:56 -05:00
Neal Cardwell c0638c247f tcp: don't fragment SACKed skbs in tcp_mark_head_lost()
In tcp_mark_head_lost() we should not attempt to fragment a SACKed skb
to mark the first portion as lost. This is for two primary reasons:

(1) tcp_shifted_skb() coalesces adjacent regions of SACKed skbs. When
doing this, it preserves the sum of their packet counts in order to
reflect the real-world dynamics on the wire. But given that skbs can
have remainders that do not align to MSS boundaries, this packet count
preservation means that for SACKed skbs there is not necessarily a
direct linear relationship between tcp_skb_pcount(skb) and
skb->len. Thus tcp_mark_head_lost()'s previous attempts to fragment
off and mark as lost a prefix of length (packets - oldcnt)*mss from
SACKed skbs were leading to occasional failures of the WARN_ON(len >
skb->len) in tcp_fragment() (which used to be a BUG_ON(); see the
recent "crash in tcp_fragment" thread on netdev).

(2) there is no real point in fragmenting off part of a SACKed skb and
calling tcp_skb_mark_lost() on it, since tcp_skb_mark_lost() is a NOP
for SACKed skbs.

Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-03 14:57:59 -05:00
Samuel Jero f541fb7e20 dccp: fix bug in sequence number validation during connection setup
This fixes a bug in the sequence number validation during the initial handshake.

The code did not treat the initial sequence numbers ISS and ISR as read-only and
did not keep state for GSR and GSS as required by the specification. This causes
problems with retransmissions during the initial handshake, causing the
budding connection to be reset.

This patch now treats ISS/ISR as read-only and tracks GSS/GSR as required.

Signed-off-by: Samuel Jero <sj323707@ohio.edu>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
2012-03-03 09:02:52 -07:00
Gerrit Renker 793734b587 dccp ccid-3: replace incorrect BUG_ON
This replaces an unjustified BUG_ON(), which could get triggered under normal
conditions: X_calc can be 0 when p > 0. X would in this case be set to the
minimum, s/t_mbi. Its replacement avoids t_ipi = 0 (unbounded sending rate).

Thanks to Jordi, Victor and Xavier who reported this.

Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.uk>
2012-03-03 09:02:36 -07:00
Andre Guedes 74fe619ef9 Bluetooth: Don't force DISCOVERY_STOPPED state in inquiry_cache_flush
We are not supposed to force DISCOVERY_STOPPED in inquiry_cache_flush
because we may break the discovery state machine. For instance, during
interleaved discovery, when we are about to start inquiry, the state
machine forcibly goes to DISCOVERY_STOPPED while it should stay in
DISCOVERY_FINDING state.

This problem results in unexpected behaviors such as sending two
mgmt_discovering events to userspace (when only one event is expected)
and Stop Discovery failures.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-03-03 01:43:02 +02:00
Johan Hedberg 2b4bf39742 Bluetooth: mgmt: Fix updating local name when powering on
When powering on we need to apply whatever name has been set through
mgmt_set_local_name. The appropriate place for this is mgmt_powered()
and not hci_setup() since this needs to be applied also if the HCI init
sequence was already completed but the adapter was still "powered off"
from a mgmt perspective due the the HCI_AUTO_OFF still being set.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
2012-03-03 01:28:47 +02:00
Johan Hedberg 4f87da80a5 Bluetooth: Remove HCI_PI_MGMT_INIT flag for sockets
This flag is of no use right now and is in fact harmful in that it
prevents the HCI_MGMT flag to be set for any controllers that may need
it after the first one that bluetoothd takes into use (the flag is
cleared for the first controller so any subsequent ones through the same
bluetoothd mgmt socket never get the HCI_MGMT flag set).

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
2012-03-03 01:28:47 +02:00
Chuck Lever 2e738fdce2 SUNRPC: Add API to acquire source address
NFSv4.0 clients must send endpoint information for their callback
service to NFSv4.0 servers during their first contact with a server.
Traditionally on Linux, user space provides the callback endpoint IP
address via the "clientaddr=" mount option.

During an NFSv4 migration event, it is possible that an FSID may be
migrated to a destination server that is accessible via a different
source IP address than the source server was.  The client must update
callback endpoint information on the destination server so that it can
maintain leases and allow delegation.

Without a new "clientaddr=" option from user space, however, the
kernel itself must construct an appropriate IP address for the
callback update.  Provide an API in the RPC client for upper layer
RPC consumers to acquire a source address for a remote.

The mechanism used by the mount.nfs command is copied: set up a
connected UDP socket to the designated remote, then scrape the source
address off the socket.  We are careful to select the correct network
namespace when setting up the temporary UDP socket.

Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2012-03-02 15:36:53 -05:00
Trond Myklebust 4e0038b6b2 SUNRPC: Move clnt->cl_server into struct rpc_xprt
When the cl_xprt field is updated, the cl_server field will also have
to change.  Since the contents of cl_server follow the remote endpoint
of cl_xprt, just move that field to the rpc_xprt.

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
[ cel: simplify check_gss_callback_principal(), whitespace changes ]
[ cel: forward ported to 3.4 ]
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2012-03-02 15:36:41 -05:00
Trond Myklebust 2446ab6070 SUNRPC: Use RCU to dereference the rpc_clnt.cl_xprt field
A migration event will replace the rpc_xprt used by an rpc_clnt.  To
ensure this can be done safely, all references to cl_xprt must now use
a form of rcu_dereference().

Special care is taken with rpc_peeraddr2str(), which returns a pointer
to memory whose lifetime is the same as the rpc_xprt.

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
[ cel: fix lockdep splats and layering violations ]
[ cel: forward ported to 3.4 ]
[ cel: remove rpc_max_reqs(), add rpc_net_ns() ]
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2012-03-02 15:36:38 -05:00
Johan Hedberg 5f15903279 Bluetooth: mgmt: Add new error code for invalid index
The index is part of the command header and not its parameters so it
makes sense to distinguish this from the invalid parameters error.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
2012-03-02 03:19:24 +02:00
Johan Hedberg d4f68526e4 Bluetooth: mgmt: Fix command status error code values
Error codes in the command status should always be from the set of
values defined for mgmt and never e.g. POSIX error codes.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
2012-03-02 03:19:24 +02:00
Johan Hedberg 9f8ce967ca Bluetooth: Fix clearing of HCI_PENDING_CLASS flag
When doing reset HCI_PENDING_CLASS is one of the flags that should be
cleared (since it's used for a pending HCI command and a reset clear all
pending commands).

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
2012-03-02 03:19:24 +02:00
David S. Miller b4017c5368 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/ethernet/broadcom/tg3.c

Conflicts in the statistics regression bug fix from 'net',
but happily Matt Carlson originally posted the fix against
'net-next' so I used that to resolve this.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-01 17:57:40 -05:00
Marcel Holtmann 17b02e6256 Bluetooth: Update MGMT and SMP timeout constants to use msecs_to_jiffies
The MGMT and SMP timeout constants are always used in form of jiffies. So
just include the conversion from msecs in the define itself. This has the
advantage of making the code where the timeout is used more readable.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-03-02 00:35:57 +02:00
Marcel Holtmann ba13ccd9b9 Bluetooth: Update L2CAP timeout constants to use msecs_to_jiffies
The L2CAP timeout constants are always used in form of jiffies. So just
include the conversion from msecs in the define itself. This has the
advantage of making the code where the timeout is used more readable.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-03-02 00:33:14 +02:00
Johan Hedberg be22b54e87 Bluetooth: mgmt: Centralize message length checks
This patch moves the command length information into the command handler
table allowing the removal of length checks from the handler functions
and doing the check in a single place before calling the handler
function.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
2012-03-01 23:55:58 +02:00
Johan Hedberg 0f4e68cf6e Bluetooth: mgmt: Move command handlers into a table
By moving the command handlers into a table (the index being equal to
the opcode) the lookup is made a bit more efficient. Having a struct to
describe each handler also paves the way to add more meta-data for each
handler, e.g. the minimum message size for the command and allow
handling of common tasks like this in a centralized place.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
2012-03-01 23:55:58 +02:00
Johan Hedberg 6a919082e9 Bluetooth: mgmt: Initialize HCI_MGMT flag for any command
The read_controller_info is typically the first command that user space
sends when taking a controller into use. This is also the reason why
this command has been used as the trigger to set the HCI_MGMT flag.
However, when not running the user-space daemon and using command line
tools it is possible that read_controller_info is not the first
controller specific command. This patch moves the HCI_MGMT
initialization to a generic place where it will be set for whatever
happens to be the first mgmt command targetting a specific controller.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
2012-03-01 23:55:58 +02:00
Johan Hedberg bdb6d97154 Bluetooth: mgmt: Refactor hci_dev lookup for commands
Almost all mgmt commands need to lookup a struct hci_dev based on the
index received within the mgmt headers. It makese therefore sense to
look this up in a single place and then just pass the hdev pointer to
each command handler function.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
2012-03-01 23:55:58 +02:00
David S. Miller 1e804aecd7 Merge branch 'master' of git://1984.lsi.us.es/net 2012-03-01 15:40:36 -05:00
Johan Hedberg 75fb0e324d Bluetooth: Fix init sequence for some CSR based controllers
Some CSR controllers will generate a spontaneous reset during init and
just eat up any pending command without sending a command complete for
it. This patch solves the issue by just resending whatever was the last
sent command. hci_send_cmd is not used since we need to bypass all other
commands in the send queue.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
2012-03-01 21:44:55 +02:00
Andre Guedes 8b90129cc5 Bluetooth: Check capabilities in BR/EDR and LE-Only discovery
This patch add an extra check for BR/EDR and LE-Only discovery.
This way, we are able to return error immediately if the discovery
type requested is not supported by the device.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-03-01 12:12:53 -03:00
Greg Rose 48752f6513 rtnetlink: Fix VF IFLA policy
Add VF spoof check to IFLA policy.  The original patch I submitted to
add the spoof checking feature to rtnl failed to add the proper policy
rule that identifies the data type and len.  This patch corrects that
oversight.  No bugs have been reported against this but it may cause
some problem for the netlink message parsing that uses the policy
table.

CC: stable@vger.kernel.org
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-02-29 23:24:00 -08:00
David S. Miller 06b8db9cac Merge branch 'tipc_net-next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux 2012-02-29 23:52:12 -05:00
Johan Hedberg 1de028ceb5 Bluetooth: mgmt: Add missing hci_dev locking to set_le()
The set_le() function was missing hci_dev locking which is e.g. critical
for the mgmt pending command adding/removing.

Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-03-01 01:28:04 -03:00
Gustavo F. Padovan 00abfe4442 Bluetooth: Fix coding style with breaking lines
Our limit is 80 and broken lines should as right as possible.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2012-03-01 01:27:54 -03:00
John W. Linville 8701ff0a88 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless 2012-02-29 14:53:21 -05:00
Johannes Berg 02f2f1a951 mac80211: handle non-bufferable MMPDUs correctly
This renames the IEEE80211_TX_CTL_POLL_RESPONSE
TX flag to IEEE80211_TX_CTL_NO_PS_BUFFER and also
uses it for non-bufferable MMPDUs (all MMPDUs but
deauth, disassoc and action frames.)

Previously, mac80211 would let the MMPDU through
but not set the flag so drivers supporting some
hardware aids for avoiding the PS races would
then reject the frame.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:14:54 -05:00
Johannes Berg 37ad38887d mac80211: make deauth/disassoc sequence more natural
The association sequence looks (roughly) like
this now:
 * set BSSID
 * set station to EXIST state
 * send auth
 * set station to AUTH state
 * send assoc
 * set station to ASSOC state
 * set BSS info to associated

In contrast, the deauth/disassoc sequence is
the other way around:
 * clear BSSID/BSS info state
 * remove station
 * send deauth/disassoc
(in some cases the last two steps are reversed.)

This patch encodes the entire sequence in the
ieee80211_set_disassoc() function and changes
it to be like this, for good measure with an
explicit flush:
 * send deauth/disassoc
 * flush
 * remove station
 * clear BSSID/BSS info state

At least iwlwifi gets confused with the other
sequence in P2P mode and complains that it
wasn't able to flush the queues.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:11:34 -05:00
Johannes Berg 02d83e60b9 mac80211: fix ieee80211_set_disassoc() sending DelBA
When ieee80211_set_disassoc() is called with the
tx argument set to true, it will send DelBA out
to the peer. This isn't useful or necessary in a
few cases where we do it today, those being when
we lost the connection or when the supplicant
explicitly asked us to not tell the AP.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:11:34 -05:00
Johannes Berg 5fef7dbcad mac80211: dont call cfg80211 from ieee80211_send_deauth_disassoc
Instead of calling cfg80211 in ieee80211_send_deauth_disassoc()
pass out the frame and call it from the caller. That saves the
SKB allocation if we don't actually want to send the frame and
enables us to make the ordering smarter in the future.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:11:34 -05:00
Johannes Berg 63c9c5e77c cfg80211: remove cookies from callbacks
In "cfg80211: no cookies in cfg80211_send_XXX()"
Holger Schurig removed the cookies in the calls
from mac80211 to cfg80211, but the ones in the
other direction were left in. Remove them now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-29 14:11:33 -05:00
Andre Guedes 53bf2426b4 Bluetooth: Fix Kconfig help description
SMP is not a kernel module, it is part of Bluetooth Core (as already
described in lines above).

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-29 18:50:25 +02:00
Allan Stephens 9bbbc59dbd tipc: Optimize setting of immutable payload message header fields
Optimizes routines that send payload messages so that they no longer
update the "originating node" and "originating port" fields of the
outgoing message header template, since these fields are initialized
when the sending port is created and never change thereafter. Also
optimizes the routine which updates the message header template when
a connection to a port is established, for the same reason.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2012-02-29 11:45:35 -05:00
Allan Stephens e8ec1ae756 tipc: Eliminate obsolete code for re-sending a message
Removes code that updated the "previous node" field of an out-going
message over TIPC's links. Such updating is unnecessary since the
removal of the prototype multi-cluster capability means that all
outgoing messages are generated locally and already have this field
populated correctly.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2012-02-29 11:45:01 -05:00
Allan Stephens 9b641251ae tipc: Un-inline port routine for processing incoming messages
Converts a non-trivial routine from inline to non-inline form
to avoid bloating the TIPC code base with 6 copies of its body.

This change is essentially cosmetic, and doesn't change existing
TIPC behavior.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2012-02-29 11:44:32 -05:00
Szymon Janc 95b23582d7 Bluetooth: Use NULL instead of integer for mgmt_device_connected param
Last param of mgmt_device_connected is of pointer type, so use NULL
instead of 0 for it. This fix following sparse warning:

CHECK   net/bluetooth/hci_event.c
net/bluetooth/hci_event.c:3262:74: warning: Using plain integer as NULL pointer

Signed-off-by: Szymon Janc <szymon@janc.net.pl>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-29 17:48:31 +02:00
Andre Guedes 426c189a1b Bluetooth: Change interleaved discovery behavior
According to last discussion on IRC, if an interleaved discovery is
issued, but the device is not dual mode, we should return error
instead of performing a regular BR/EDR or LE-only discovery.

Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-29 16:21:04 +02:00
Andrei Emeltchenko 978c93b90f Bluetooth: Save remote L2CAP fixed channel mask
Fixed channel mask needs to be stored to decide whether to
use A2MP for example. So far save only one relevant byte which
keeps all information we need.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-29 16:20:19 +02:00
Dan Carpenter 89bb46d020 Bluetooth: change min_t() cast in hci_reassembly()
"count" is type int so the cast to __u16 truncates the high bits away
and triggers a Smatch static checker warning.  It looks like a high
value of count could cause a forever loop, but I didn't follow it
through to see if count is capped somewhere.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-29 16:19:37 +02:00
Dan Carpenter 3379013bcf Bluetooth: use kfree_skb() instead of kfree()
sk_buffs should be freed using kfree_skb().

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-29 16:18:03 +02:00
David S. Miller 0695512a57 Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge 2012-02-28 15:07:52 -05:00
Neal Cardwell 4c90d3b303 tcp: fix false reordering signal in tcp_shifted_skb
When tcp_shifted_skb() shifts bytes from the skb that is currently
pointed to by 'highest_sack' then the increment of
TCP_SKB_CB(skb)->seq implicitly advances tcp_highest_sack_seq(). This
implicit advancement, combined with the recent fix to pass the correct
SACKed range into tcp_sacktag_one(), caused tcp_sacktag_one() to think
that the newly SACKed range was before the tcp_highest_sack_seq(),
leading to a call to tcp_update_reordering() with a degree of
reordering matching the size of the newly SACKed range (typically just
1 packet, which is a NOP, but potentially larger).

This commit fixes this by simply calling tcp_sacktag_one() before the
TCP_SKB_CB(skb)->seq advancement that can advance our notion of the
highest SACKed sequence.

Correspondingly, we can simplify the code a little now that
tcp_shifted_skb() should update the lost_cnt_hint in all cases where
skb == tp->lost_skb_hint.

Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-28 15:06:46 -05:00
Sven Eckelmann 7c64fd98ce batman-adv: Fix indentation of multiline statements
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
2012-02-28 19:14:31 +08:00
Ingo Molnar bdd4431c8d Merge branch 'rcu/next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu into core/rcu
The major features of this series are:

 - making RCU more aggressive about entering dyntick-idle mode in order to
   improve energy efficiency

 - converting a few more call_rcu()s to kfree_rcu()s

 - applying a number of rcutree fixes and cleanups to rcutiny

 - removing CONFIG_SMP #ifdefs from treercu

 - allowing RCU CPU stall times to be set via sysfs

 - adding CPU-stall capability to rcutorture

 - adding more RCU-abuse diagnostics

 - updating documentation

 - fixing yet more issues located by the still-ongoing top-to-bottom
   inspection of RCU, this time with a special focus on the
   CPU-hotplug code path.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2012-02-28 10:16:10 +01:00
Johan Hedberg 02b7cc62b6 Bluetooth: Use LMP_HOST_SSP define instead of magic values
This patch fixes the code to use the proper LMP_HOST_SSP define instead
of magic values and thereby makes the code more readable.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
2012-02-28 02:30:00 +02:00
Johan Hedberg 8f984dfaf0 Bluetooth: Remove redundant read_host_features commands
Previously the write_le_enable would trigger a read_host_features
command but since we have access to the value LE support was set to we
can simply just clear or set the bit in hdev->host_features. This also
removes a second unnecessary read_host_features command from the device
initialization procedure since LE is only enabled after the first
read_host_features command completes.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
2012-02-28 01:54:19 +02:00
Johan Hedberg 0b60eba1b2 Bluetooth: Don't send unnecessary write_le_enable command
If the local host features indicate that LE is already in the state that
is desired there's no point in sending the HCI command to try to change
the setting.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
2012-02-28 01:52:34 +02:00
Johannes Berg 005e472b45 mac80211: remove local_to_hw
That's a lot longer than open-coding it and
doesn't really add value, so just remove it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:42 -05:00
Johannes Berg 3431683759 mac80211: fix sta_info_flush() return value
The comment for sta_info_flush() states
"Returns the number of removed STA entries"
but that isn't actually true. Consequently,
the warning when a station is still around
on interface removal can never trigger and
this delayed finding the timer issue the
previous patch fixed. Fix the return value
here to make that warning useful again.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:42 -05:00
Johannes Berg 54e4ffb2ab mac80211: fix auth/assoc data & timer leak
When removing an interface while it is in the
process of authenticating or associating, we
leak the auth_data or assoc_data, and leave
the timer pending. The timer then crashes the
system when it fires as its data is gone.

Fix this by explicitly deleting all the data
when the interface is removed. This uncovered
another bug -- this problem should have been
detected by the sta_info_flush() warning but
that function doesn't ever return non-zero,
I'll fix that in a separate patch.

Reported-by: Hieu Nguyen <hieux.c.nguyen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:42 -05:00
Jakub Kicinski 9d88c7f670 mac80211: use proper sub_if_data on suspend path
Use interface data from sta instead of invalid pointer
to list head in calls to drv_sta_state.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:40 -05:00
Johannes Berg 79ebfb85d4 mac80211: fix associated vs. idle race
Eliad reports that if a scan finishes in the
middle of processing associated (however it
happens), the interface can go idle. This is
because we set assoc_data to NULL before we
set associated. Change the order so any idle
check will find either one of them.

Doing this requires duplicating the TX sync
processing, but I already have a patch to
delete that completely and will submit that
as soon as my driver changes to no longer
require it are submitted.

Reported-by: Eliad Peller <eliad@wizery.com>
Tested-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:32 -05:00
Johannes Berg d26ad3771f mac80211: clean up asm/unaligned.h inclusion
Some files implicitly get this via mesh.h
which itself doesn't need it, so move the
inclusion into the right files. Some other
files don't need it at all but include it,
so remove it from there.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:32 -05:00
Eliad Peller 6b5773ebd5 mac80211: remove redundant monitor_work enqueueing
ieee80211_restart_sta_timer() takes care for enqueueing
monitor_work if needed, so no need to do it again.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:32 -05:00
Eliad Peller 494f1fe559 mac80211: don't queue monitor work for HW_CONNECTION_MONITOR
Devices that monitor the connection in the hw don't need
the monitor work in the driver.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-02-27 14:06:31 -05:00
Stanislav Kinsbursky 591ad7feae SUNRPC: move waitq from RPC pipe to RPC inode
Currently, wait queue, used for polling of RPC pipe changes from user-space,
is a part of RPC pipe. But the pipe data itself can be released on NFS umount
prior to dentry-inode pair, connected to it (is case of this pair is open by
some process).
This is not a problem for almost all pipe users, because all PipeFS file
operations checks pipe reference prior to using it.
Except evenfd. This thing registers itself with "poll" file operation and thus
has a reference to pipe wait queue. This leads to oopses on destroying eventfd
after NFS umount (like rpc_idmapd do) since not pipe data left to the point
already.
The solution is to wait queue from pipe data to internal RPC inode data. This
looks more logical, because this wiat queue used only for user-space processes,
which already holds inode reference.

Note: upcalls have to get pipe->dentry prior to dereferecing wait queue to make
sure, that mount point won't disappear from underneath us.

Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2012-02-27 13:37:48 -05:00
Stanislav Kinsbursky 2c9030eef9 SUNRPC: check RPC inode's pipe reference before dereferencing
There are 2 tightly bound objects: pipe data (created for kernel needs, has
reference to dentry, which depends on PipeFS mount/umount) and PipeFS
dentry/inode pair (created on mount for user-space needs). They both
independently may have or have not a valid reference to each other.
This means, that we have to make sure, that pipe->dentry reference is valid on
upcalls, and dentry->pipe reference is valid on downcalls. The latter check is
absent - my fault.
IOW, PipeFS dentry can be opened by some process (rpc.idmapd for example), but
it's pipe data can belong to NFS mount, which was unmounted already and thus
pipe data was destroyed.
To fix this, pipe reference have to be set to NULL on rpc_unlink() and checked
on PipeFS file operations instead of pipe->dentry check.

Note: PipeFS "poll" file operation will be updated in next patch, because it's
logic is more complicated.

Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2012-02-27 13:37:09 -05:00
Stanislav Kinsbursky da3b462296 SUNRPC: release per-net clients lock before calling PipeFS dentries creation
v3:
1) Lookup for client is performed from the beginning of the list on each PipeFS
event handling operation.

Lockdep is sad otherwise, because inode mutex is taken on PipeFS dentry
creation, which can be called on mount notification, where this per-net client
lock is taken on clients list walk.

Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2012-02-27 13:36:16 -05:00
John W. Linville eea79e0713 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem 2012-02-27 13:14:47 -05:00
Johan Hedberg 816a11d5ce Bluetooth: Use kernel int types instead of ones from stdint.h
u8/__u8/u32/etc should be used in the kernel instead of stdint.h types.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
2012-02-27 12:34:39 +02:00
David S. Miller ff4783ce78 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/ethernet/sfc/rx.c

Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-26 21:55:51 -05:00
Jim Garlick 208f3c28aa net/9p: handle flushed Tclunk/Tremove
When a Tclunk or Tremove request is flushed, the fid is not freed on the
server.

p9_client_clunk() should retry once on interrupt, then if interrupted
again, leak the fid for the duration of the connection.

p9_client_remove() should call p9_client_clunk() on interrupt
instead of unconditionally destroying the fid.

Signed-off-by: Jim Garlick <garlick@llnl.gov>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
2012-02-26 14:49:57 -06:00
Linus Torvalds 203738e548 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
1) ICMP sockets leave err uninitialized but we try to return it for the
   unsupported MSG_OOB case, reported by Dave Jones.

2) Add new Zaurus device ID entries, from Dave Jones.

3) Pointer calculation in hso driver memset is wrong, from Dan
   Carpenter.

4) ks8851_probe() checks unsigned value as negative, fix also from Dan
   Carpenter.

5) Fix crashes in atl1c driver due to TX queue handling, from Eric
   Dumazet.  I anticipate some TX side locking fixes coming in the near
   future for this driver as well.

6) The inline directive fix in Bluetooth which was breaking the build
   only with very new versions of GCC, from Johan Hedberg.

7) Fix crashes in the ATP CLIP code due to ARP cleanups this merge
   window, reported by Meelis Roos and fixed by Eric Dumazet.

8) JME driver doesn't flush RX FIFO correctly, from Guo-Fu Tseng.

9) Some ip6_route_output() callers test the return value for NULL, but
   this never happens as the convention is to return a dst entry with
   dst->error set.  Fixes from RonQing Li.

10) Logitech Harmony 900 should be handled by zaurus driver not
   cdc_ether, update white lists and black lists accordingly.  From
   Scott Talbert.

11) Receiving from certain kinds of devices there won't be a MAC header,
   so there is no MAC header to fixup in the IPSEC code, and if we try
   to do it we'll crash.  Fix from Eric Dumazet.

12) Port type array indexing off-by-one in mlx4 driver, fix from Yevgeny
   Petrilin.

13) Fix regression in link-down handling in davinci_emac which causes
   all RX descriptors to be freed up and therefore RX to wedge
   completely, from Christian Riesch.

14) It took two attempts, but ctnetlink soft lockups seem to be
   cured now, from Pablo Neira Ayuso.

15) Endianness bug fix in ENIC driver, from Santosh Nayak.

16) The long ago conversion of the PPP fragmentation code over to
   abstracted SKB list handling wasn't perfect, once we get an
   out of sequence SKB we don't flush the rest of them like we
   should.  From Ben McKeegan.

17) Fix regression of ->ip_summed initialization in sfc driver.
   From Ben Hutchings.

18) Bluetooth timeout mistakenly using msecs instead of jiffies,
   from Andrzej Kaczmarek.

19) Using _sync variant of work cancellation results in deadlocks,
   use the non _sync variants instead.  From Andre Guedes.

20) Bluetooth rfcomm code had reference counting problems leading
   to crashes, fix from Octavian Purdila.

21) The conversion of netem over to classful qdisc handling added
   two bugs to netem_dequeue(), fixes from Eric Dumazet.

22) Missing pci_iounmap() in ATM Solos driver.  Fix from Julia Lawall.

23) b44_pci_exit() should not have __exit tag since it's invoked from
   non-__exit code.  From Nikola Pajkovsky.

24) The conversion of the neighbour hash tables over to RCU added a
   race, fixed here by adding the necessary reread of tbl->nht, fix
   from Michel Machado.

25) When we added VF (virtual function) attributes for network device
   dumps, this potentially bloats up the size of the dump of one
   network device such that the dump size is too large for the buffer
   allocated by properly written netlink applications.

   In particular, if you add 255 VFs to a network device, parts of
   GLIBC stop working.

   To fix this, we add an attribute that is used to turn on these
   extended portions of the network device dump.  Sophisticaed
   applications like 'ip' that want to see this stuff  will be changed
   to set the attribute, whereas things like GLIBC that don't care
   about VFs simply will not, and therefore won't be busted by the
   mere presence of VFs on a network device.

   Thanks to the tireless work of Greg Rose on this fix.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
  sfc: Fix assignment of ip_summed for pre-allocated skbs
  ppp: fix 'ppp_mp_reconstruct bad seq' errors
  enic: Fix endianness bug.
  gre: fix spelling in comments
  netfilter: ctnetlink: fix soft lockup when netlink adds new entries (v2)
  Revert "netfilter: ctnetlink: fix soft lockup when netlink adds new entries"
  davinci_emac: Do not free all rx dma descriptors during init
  mlx4_core: Fixing array indexes when setting port types
  phy: IC+101G and PHY_HAS_INTERRUPT flag
  netdev/phy/icplus: Correct broken phy_init code
  ipsec: be careful of non existing mac headers
  Move Logitech Harmony 900 from cdc_ether to zaurus
  hso: memsetting wrong data in hso_get_count()
  netfilter: ip6_route_output() never returns NULL.
  ethernet/broadcom: ip6_route_output() never returns NULL.
  ipv6: ip6_route_output() never returns NULL.
  jme: Fix FIFO flush issue
  atm: clip: remove clip_tbl
  ipv4: ping: Fix recvmsg MSG_OOB error handling.
  rtnetlink: Fix problem with buffer allocation
  ...
2012-02-26 12:47:17 -08:00
Jim Garlick a314f2748e net/9p: don't allow Tflush to be interrupted
When a signal is received while sending a Tflush, the client,
which has recursed into p9_client_rpc() while sending another request,
should wait for Rflush as long as the transport is still up.

Signed-off-by: Jim Garlick <garlick@llnl.gov>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
2012-02-26 14:27:21 -06:00
Pablo Neira Ayuso 0f298a285f netfilter: ctnetlink: support kernel-space dump filtering by ctmark
This patch adds CTA_MARK_MASK which, together with CTA_MARK, allows
you to selectively send conntrack entries to user-space by
returning those that match mark & mask.

With this, we can save cycles in the building and the parsing of
the entries that may be later on filtered out in user-space by using
the ctmark & mask.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-26 14:12:33 -05:00
Pablo Neira Ayuso 7175c88307 netlink: allow to pass data pointer to netlink_dump_start() callback
This patch allows you to pass a data pointer that can be
accessed from the dump callback.

Netfilter is going to use this patch to provide filtered dumps
to user-space. This is specifically interesting in ctnetlink that
may handle lots of conntrack entries. We can save precious
cycles by skipping the conversion to TLV format of conntrack
entries that are not interesting for user-space.

More specifically, ctnetlink will include one operation to allow
to filter the dumping of conntrack entries by ctmark values.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-26 14:10:44 -05:00
Pablo Neira Ayuso 80d326fab5 netlink: add netlink_dump_control structure for netlink_dump_start()
Davem considers that the argument list of this interface is getting
out of control. This patch tries to address this issue following
his proposal:

struct netlink_dump_control c = { .dump = dump, .done = done, ... };

netlink_dump_start(..., &c);

Suggested by David S. Miller.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-26 14:10:06 -05:00
Florian Westphal e899b1119f netfilter: bridge: fix module autoload in compat case
We expected 0 if module doesn't exist, which is no longer the case
(42046e2e45,
netfilter: x_tables: return -ENOENT for non-existant matches/targets).

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2012-02-25 14:29:09 +01:00
David S. Miller e807e566e9 Merge branch 'master' of git://1984.lsi.us.es/net 2012-02-24 17:41:57 -05:00
stephen hemminger bff528578f gre: fix spelling in comments
The original spelling and bad word choice makes these comments hard to read.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-24 17:41:11 -05:00
Allan Stephens b58343f9ea tipc: Eliminate support for tipc_mode global variable
Removes all references to the global variable that records whether
TIPC is running in "single node" mode or "network" mode, since this
information can be easily deduced from the global variable that
records TIPC's network address. (i.e. a non-zero network address
means that TIPC is running in network mode.)

The changes made update most existing mode-based checks to use the
network address global variable. A few checks that are no longer
needed are removed entirely, along with any associated code lying on
non-executable control paths.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2012-02-24 17:05:17 -05:00
Allan Stephens 077a26f029 tipc: Eliminate obsolete support for "not running" mode
Removes all references to TIPC's "not running" mode, since the
removal of support for the native API means that there is no longer
any way to interact with TIPC if it has not been initialized.

The changes made consist of removing mode-based checks that are no
longer needed, along with any associated code lying on non-executable
control paths.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2012-02-24 17:05:17 -05:00
Allan Stephens bc9f8143ec tipc: Revert name table translation optimization
Restores name table translation using a non-zero domain that is
"out of scope", which was broken by an earlier commit
(5d9c54c1e9). Comments have now been
added to the name table translation routine to make it clear that
there are actually three possible outcomes to a translation request
(found/not found/deferred), rather than just two (found/not found).

Note that a straightforward revert of the earlier commit is not
possible, as other changes to the name table translation logic
have occurred since the incorrect optimization was made.

Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2012-02-24 17:05:17 -05:00