In Tiger Lake the Firmware CM is always enabled (so bit 0 is always set)
but it may be in "pass through" mode which means it requires Software CM
instead. This can be determined by checking bit 31 instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tiger Lake integrated Thunderbolt/USB4 controller is quite close to
Intel Ice Lake. By default it is still using firmware based connection
manager so we can use most of the Ice Lake flows in Tiger Lake as well.
We check if the firmware connection manager is running and in that case
use it, otherwise use the software based connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since now we can do pretty much the same thing in the software
connection manager than the firmware would do, there is no point
starting it by default. Instead we can just continue using the software
connection manager.
Make it possible for user to switch between the two by adding a module
pararameter (start_icm) which is by default false. Having this ability
to enable the firmware may be useful at least when debugging possible
issues with the software connection manager implementation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Lane bonding allows aggregating two 10/20 Gb/s (depending on the
generation) lanes into a single 20/40 Gb/s bonded link. This allows
sharing the full bandwidth more efficiently. In order to establish lane
bonding we need to check that lane bonding is possible through link
controller and that both ends of the link actually supports 2x widths.
This also means that all the paths should be established through the
primary port so update tb_path_alloc() to handle this as well.
Lane bonding is supported starting from Falcon Ridge (2nd generation)
controllers.
We also expose the current speed and number of lanes under each device
except the host router following similar attribute naming than USB bus.
Expose speed and number of lanes for both directions to allow possibility
of asymmetric link in the future.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently add_switch() takes a huge amount of parameters that makes it
hard to maintain. Instead of passing all those parameters we can split
the function into two parts (alloc and add) and fill the additional
switch fields directly in the functions calling those.
While there remove redundant error logging in case kmemdup() fails.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There are quite many places in the driver where we iterate over each
port in the switch. To make it bit more convenient, add a macro that can
be used to iterate over each port and convert existing call sites to use it.
This is based on code by Lukas Wunner.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The Thunderbolt controller is integrated into the Ice Lake CPU itself
and requires special flows to power it on and off using force power bit
in NHI VSEC registers. Runtime PM (RTD3) and Sx flows also differ from
the discrete solutions. Now the firmware notifies the driver whether
RTD3 entry or exit are possible. The driver is responsible of sending
Go2Sx command through link controller mailbox when system enters Sx
states (suspend-to-mem/disk). Rest of the ICM firwmare flows follow
Titan Ridge.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
This is depends on the controller and on the platform/CPU we are
running. Move it to struct icm so we can set it per controller.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
When starting ICM firmware on Apple systems we need to perform CIO reset
as part of the flow. However, it turns out that the reset register has
changed to another location in Titan Ridge.
Fix this by introducing ->cio_reset() callback with corresponding
implementations for Alpine and Titan Ridge.
Fixes: c4630d6ae6 ("thunderbolt: Start firmware on Titan Ridge Apple systems")
Reported-by: Peter Bowen <pzb@amazon.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When a device is authorized from userspace by writing to authorized
attribute we first take the domain lock and then runtime resume the
device in question. There are two issues with this.
First is that the device connected notifications are blocked during this
time which means we get them only after the authorization operation is
complete. Because of this the authorization needed flag from the
firmware notification is not reflecting the real authorization status
anymore. So what happens is that the "authorized" keeps returning 0 even
if the device was already authorized properly.
Second issue is that each time the controller is runtime resumed the
connection_id field of device connected notification may be different
than in the previous resume. We need to use the latest connection_id
otherwise the firmware rejects the authorization command.
Fix these by moving runtime resume operations to happen before the
domain lock is taken, and waiting for the updated device connected
notification from the firmware before we allow runtime resume of a
device to complete.
While there add missing locking to tb_switch_nvm_read().
Fixes: 09f11b6c99 ("thunderbolt: Take domain lock in switch sysfs attribute callbacks")
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Titan Ridge flow to start the firmware is the same as Alpine Ridge so we
can do the same on Titan Ridge based Apple systems.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that the driver can handle every possible tunnel types there is no
point to log everything as info level so turn these to happen at debug
level instead.
While at it remove duplicated tunnel activation log message
(tb_tunnel_activate() calls tb_tunnel_restart() which print the same
message) and add one missing '\n' termination.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to detect possible connections to other domains we need to be
able to find out why tb_switch_alloc() fails so make it return ERR_PTR()
instead. This allows the caller to differentiate between errors such as
-ENOMEM which comes from the kernel and for instance -EIO which comes
from the hardware when trying to access the possible switch.
Convert all the current call sites to handle this properly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently the driver only assigns remote port for the primary port if in
case of dual link. This makes things such as walking from one port to
another more complex than necessary because the code needs to change
from secondary to primary port if the path that is established is
created using secondary links.
In order to always assign both remote pointers we need to prevent the
scanning code from following the secondary link. Failing to do that
might cause problems as the same switch may be enumerated twice (or
removed in case of unplug). Handle that properly by introducing a new
function tb_port_has_remote() that returns true only for the primary
port. We also update tb_is_upstream_port() to support both dual link
ports, make it take const port pointer and move it below
tb_upstream_port() to keep similar functions close.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Maximum depth in Thunderbolt topology is 6 so make sure it is not
possible to allocate switches that exceed the depth limit.
While at it update tb_switch_alloc() to use upper/lower_32_bits()
following tb_switch_alloc_safe_mode().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
tb_switch_find_by_route() does the same already so use it instead and
remove duplicated get_switch_at_route().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
uuid in add_switch is allocted via kmemdup which can fail. The patch
logs the error and cleans up the allocated memory for switch.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This gets rid of the licence boilerplate duplicated in each file. While
there fix doubled space in domain.c author line.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is a long chain of devices connected when the driver is loaded
ICM sends device connected event for each and those are put to tb->wq
for later processing. Now if the driver gets unloaded in the middle, so
that the work queue is not yet empty it gets flushed by tb_domain_stop().
However, by that time the root switch is already removed so the driver
crashes when it tries to dereference it in ICM event handling callbacks.
Fix this by checking whether the root switch is already removed. If it
is we know that the domain is stopped and we should merely skip handling
the event.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Thunderbolt host controller is set to RTD3 mode (Runtime D3) it is
present all the time. Because of this it is important to runtime suspend
the controller whenever possible. In case of ICM we have following rules
which all needs to be true before the host controller can be put to D3:
- The controller firmware reports to support RTD3
- All the connected devices announce support for RTD3
- There is no active XDomain connection
Implement this using standard Linux runtime PM APIs so that when all the
children devices are runtime suspended, the Thunderbolt host controller
PCI device is runtime suspended as well. The ICM firmware then starts
powering down power domains towards RTD3 but it can prevent this if it
detects that there is an active Display Port stream (this is not visible
to the software, though).
The Thunderbolt host controller will be runtime resumed either when
there is a remote wake event (device is connected or disconnected), or
when there is access from userspace that requires hardware access.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'approved' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'approved' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The correct way to put the ICM into suspend state is to send it
NHI_MAILBOX_DRV_UNLOADS mailbox command. NHI_MAILBOX_SAVE_DEVS is not
needed on Intel Titan Ridge so we can skip it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This command is not really fast and can make resume time slower. We only
need to get route again if the link was changed and during initial
device connected message.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the boot ACL entry is already NULL we should not fill in the upper
two DWs with 0xfffffffff. Otherwise they are not shown as empty entries
when the sysfs attribute is read.
Fixes: 9aaa3b8b4c ("thunderbolt: Add support for preboot ACL")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Lenovo ThinkPad Yoga 370 (and possibly some other Lenovo models as
well) the Thunderbolt host controller sometimes comes up in such way
that the ICM firmware is not running properly. This is most likely an
issue in BIOS/firmware but as side-effect driver crashes the kernel due
to NULL pointer dereference:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000980
IP: pci_write_config_dword+0x5/0x20
Call Trace:
pcie2cio_write+0x3b/0x70 [thunderbolt]
icm_driver_ready+0x168/0x260 [thunderbolt]
? tb_ctl_start+0x50/0x70 [thunderbolt]
tb_domain_add+0x73/0xf0 [thunderbolt]
nhi_probe+0x182/0x300 [thunderbolt]
local_pci_probe+0x42/0xa0
? pci_match_device+0xd9/0x100
pci_device_probe+0x146/0x1b0
driver_probe_device+0x315/0x480
...
Instead of crashing update the driver to bail out gracefully if we
encounter such situation.
Fixes: f67cf49117 ("thunderbolt: Add support for Internal Connection Manager (ICM)")
Reported-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Cc: stable@vger.kernel.org
Intel Titan Ridge is the next Thunderbolt 3 controller. The ICM firmware
message format in Titan Ridge differs from Falcon Ridge and Alpine Ridge
somewhat because it is using route strings addressing devices. In
addition to that the DMA port of 4-channel (two port) controller is in
different port number than the previous controllers. There are some
other minor differences as well.
This patch add support for Intel Titan Ridge and the new ICM firmware
message format.
Signed-off-by: Radion Mirchevsky <radion.mirchevsky@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Preboot ACL is a mechanism that allows connecting Thunderbolt devices
boot time in more secure way than the legacy Thunderbolt boot support.
As with the legacy boot option, this also needs to be enabled from the
BIOS before booting is allowed. Difference to the legacy mode is that
the userspace software explicitly adds device UUIDs by sending a special
message to the ICM firmware. Only the devices listed in the boot ACL are
connected automatically during the boot. This works in both "user" and
"secure" security levels.
We implement this in Linux by exposing a new sysfs attribute (boot_acl)
below each Thunderbolt domain. The userspace software can then update
the full list as needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
In various cases, Thunderbolt device can be connected by ICM on boot
without waiting for approval from user. Most cases are related to
OEM-specific BIOS configurations. This information is interesting for
user-space as if the device isn't in SW ACL, it may create a friction in
the user experience where the device is automatically authorized if it's
connected on boot but requires an explicit user action if connected
after OS is up. User-space can use this information to suggest adding
the device to SW ACL for auto-authorization on later connections.
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Intel Titan Ridge uses slightly different format for ICM driver ready
response, so add a new ->driver_ready() callback to struct icm and move
the existing handling to a separate function which we then use in Falcon
Ridge and Alpine Ridge.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
We will be using this from Titan Ridge support code as well so make it
constant.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
The newer ICM will not use link and depth to address devices. Instead it
uses route strings. In order to take advantage of the existing code
factor out common operations so that we can use the same functions with
the new ICM as well.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
The ICM firmware rejects devices if the maximum topology limit is
exceeded (more than 6 devices are connected). If that happens just log a
message to the kernel message buffer and bail out.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Sometimes during cold boot ICM has not yet authenticated the active NVM
image leading to timeout and failing the driver probe. Allow ICM to take
some more time and increase the timeout to 3 seconds before we give up.
While there fix icm_firmware_init() to return the real error code
without overwriting it with -ENODEV.
Fixes: f67cf49117 ("thunderbolt: Add support for Internal Connection Manager (ICM)")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@vger.kernel.org
In some case reading root switch config space takes longer than what we
are currently waiting in the driver resulting timeout and failure.
Increase number of retries to allow some more time for the root switch
config space to become accesssible.
Also log an error if the timeout is exceeded so we know why the driver
probe failed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
If the system is suspended and user disconnects cable to another host
and connects it to a Thunderbolt device instead we get a warning from
driver core about adding duplicate sysfs attribute and adding the new
device fails.
Handle this properly so that we first remove the existing XDomain
connection before adding new devices.
Fixes: d1ff70241a ("thunderbolt: Add support for XDomain discovery protocol")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@vger.kernel.org
When two hosts are connected over a Thunderbolt cable, there is a
protocol they can use to communicate capabilities supported by the host.
The discovery protocol uses automatically configured control channel
(ring 0) and is build on top of request/response transactions using
special XDomain primitives provided by the Thunderbolt base protocol.
The capabilities consists of a root directory block of basic properties
used for identification of the host, and then there can be zero or more
directories each describing a Thunderbolt service and its capabilities.
Once both sides have discovered what is supported the two hosts can
setup high-speed DMA paths and transfer data to the other side using
whatever protocol was agreed based on the properties. The software
protocol used to communicate which DMA paths to enable is service
specific.
This patch adds support for the XDomain discovery protocol to the
Thunderbolt bus. We model each remote host connection as a Linux XDomain
device. For each Thunderbolt service found supported on the XDomain
device, we create Linux Thunderbolt service device which Thunderbolt
service drivers can then bind to based on the protocol identification
information retrieved from the property directory describing the
service.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Thunderbolt service might need to find the physical port from a link
the cable is connected to. For instance networking driver uses this
information to generate MAC address according the Apple ThunderboltIP
protocol.
Move this function to thunderbolt.h and rename it to
tb_phy_port_from_link() to reflect the fact that it does not take switch
as parameter.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're about to amend ACPI bus scan with DMI checks whether we're running
on a Mac to support Apple device properties in AML. The DMI checks are
performed for every single device, adding overhead for everything x86
that isn't Apple, which is the majority. Rafael and Andy therefore
request to perform the DMI match only once and cache the result.
Outside of ACPI various other Apple DMI checks exist and it seems
reasonable to use the cached value there as well. Rafael, Andy and
Darren suggest performing the DMI check in arch code and making it
available with a header in include/linux/platform_data/x86/.
To this end, add early_platform_quirks() to arch/x86/kernel/quirks.c
to perform the DMI check and invoke it from setup_arch(). Switch over
all existing Apple DMI checks, thereby fixing two deficiencies:
* They are now #defined to false on non-x86 arches and can thus be
optimized away if they're located in cross-arch code.
* Some of them only match "Apple Inc." but not "Apple Computer, Inc.",
which is used by BIOSes released between January 2006 (when the first
x86 Macs started shipping) and January 2007 (when the company name
changed upon introduction of the iPhone).
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Suggested-by: Darren Hart <dvhart@infradead.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On one of my test machines nhi_mailbox_cmd() called from icm_suspend()
times out and returnes an error which then is propagated to the
caller and causes the entire system suspend to be aborted which isn't
very useful.
Instead of aborting system suspend, print the error into the log
and continue.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Michael Jamet <michael.jamet@intel.com>
Starting from Intel Falcon Ridge the NVM firmware can be upgraded by
using DMA configuration based mailbox commands. If we detect that the
host or device (device support starts from Intel Alpine Ridge) has the
DMA configuration based mailbox we expose NVM information to the
userspace as two separate Linux NVMem devices: nvm_active and
nvm_non_active. The former is read-only portion of the active NVM which
firmware upgrade tools can be use to find out suitable NVM image if the
device identification strings are not enough.
The latter is write-only portion where the new NVM image is to be
written by the userspace. It is up to the userspace to find out right
NVM image (the kernel does very minimal validation). The ICM firmware
itself authenticates the new NVM firmware and fails the operation if it
is not what is expected.
We also expose two new sysfs files per each switch: nvm_version and
nvm_authenticate which can be used to read the active NVM version and
start the upgrade process.
We also introduce safe mode which is the mode a switch goes when it does
not have properly authenticated firmware. In this mode the switch only
accepts a couple of commands including flashing a new NVM firmware image
and triggering power cycle.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from Intel Falcon Ridge the internal connection manager running
on the Thunderbolt host controller has been supporting 4 security
levels. One reason for this is to prevent DMA attacks and only allow
connecting devices the user trusts.
The internal connection manager (ICM) is the preferred way of connecting
Thunderbolt devices over software only implementation typically used on
Macs. The driver communicates with ICM using special Thunderbolt ring 0
(control channel) messages. In order to handle these messages we add
support for the ICM messages to the control channel.
The security levels are as follows:
none - No security, all tunnels are created automatically
user - User needs to approve the device before tunnels are created
secure - User need to approve the device before tunnels are created.
The device is sent a challenge on future connects to be able
to verify it is actually the approved device.
dponly - Only Display Port and USB tunnels can be created and those
are created automatically.
The security levels are typically configurable from the system BIOS and
by default it is set to "user" on many systems.
In this patch each Thunderbolt device will have either one or two new
sysfs attributes: authorized and key. The latter appears for devices
that support secure connect.
In order to identify the device the user can read identication
information, including UUID and name of the device from sysfs and based
on that make a decision to authorize the device. The device is
authorized by simply writing 1 to the "authorized" sysfs attribute. This
is following the USB bus device authorization mechanism. The secure
connect requires an additional challenge step (writing 2 to the
"authorized" attribute) in future connects when the key has already been
stored to the NVM of the device.
Non-ICM systems (before Alpine Ridge) continue to use the existing
functionality and the security level is set to none. For systems with
Alpine Ridge, even on Apple hardware, we will use ICM.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mika Westerberg