Add missing documentation of structure members and
modify the order of documentation to match that of
the structure declaration.
Signed-off-by: Dov Levenglick <dov.levenglick@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add following USB speed related PHY modes:
LS (Low Speed), FS (Full Speed), HS (High Speed), SS (Super Speed)
Speed related information is required by some QCOM PHY drivers
to program PHY monitor resume/remote-wakeup events in suspended
state. Speed is needed in order to set correct polarity of wakeup
events for detection. E.g. QUSB2 PHY monitors DP/DM line state
depending on whether speed is LS or FS/HS to detect resume.
Similarly QMP USB3 PHY in SS mode should monitor RX terminations
attach/detach and LFPS events depending on SSPHY is active or not.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along with
phy and chipidea enhancements. There's also a lot of SPDX tags and
license boilerplate cleanups as well, which provide some churn in the
diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see happen.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
1CeLipqVIN3IsMMJptvb
=zvDI
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some quirky UDCs (like dwc3 on Exynos) need to have their phys calibrated e.g.
for using super speed. This patch adds a new phy_calibrate() method.
When the calibration should be used is dependent on actual chip.
In case of dwc3 on Exynos the calibration must happen after usb_add_hcd()
(while in host mode), because certain phy parameters like Tx LOS levels
and boost levels need to be calibrated further post initialization of xHCI
controller, to get SuperSpeed operations working. But an hcd must be
prepared first in order to pass it to usb_add_hcd(), so, in particular, dwc3
registers must be available first, and in order for the latter to happen
the phys must be initialized. This poses a chicken and egg problem if
the calibration were to be performed in phy_init(). To break the circular
dependency a separate method is added which can be called at a desired
moment after phy intialization.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Refactor ufs_qcom_power_up_sequence() to get rid of ugly
exported phy APIs and use the phy_init() and phy_power_on()
to do the phy initialization.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
UFS phy has two modes for each High speed generation.
These modes are identified by two rates of operations -
Rate A, and Rate B.
Add these UFS phy modes to phy framework.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If we're trying to get a handle to an optional phy, then the phy framework
being disabled shouldn't return an hard error.
Instead, return NULL just like phy_optional_get does when there's no phy
provided in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds more generic PHY modes to the phy_mode enum, to
allow configuring generic PHYs to the SGMII and/or the 10GKR mode
by using the set_mode callback.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although ULPI phy is currently being used by tusb1210,
there can be other consumers too in future. So move this
to the includes path for phy.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas). There's also
an assortment of minor fixes, mostly in error legs or other not very
user visible stuff. The major change is the pci_alloc_irq_vectors
replacement for the old pci_msix_.. calls; this effectively makes IRQ
mapping generic for the drivers and allows blk_mq to use the
information.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sPXh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
lpfc, hisi_sas, megaraid_sas, ufs, ibmvscsis, mpt3sas).
There's also an assortment of minor fixes, mostly in error legs or
other not very user visible stuff. The major change is the
pci_alloc_irq_vectors replacement for the old pci_msix_.. calls; this
effectively makes IRQ mapping generic for the drivers and allows
blk_mq to use the information"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (256 commits)
scsi: qla4xxx: switch to pci_alloc_irq_vectors
scsi: hisi_sas: support deferred probe for v2 hw
scsi: megaraid_sas: switch to pci_alloc_irq_vectors
scsi: scsi_devinfo: remove synchronous ALUA for NETAPP devices
scsi: be2iscsi: set errno on error path
scsi: be2iscsi: set errno on error path
scsi: hpsa: fallback to use legacy REPORT PHYS command
scsi: scsi_dh_alua: Fix RCU annotations
scsi: hpsa: use %phN for short hex dumps
scsi: hisi_sas: fix free'ing in probe and remove
scsi: isci: switch to pci_alloc_irq_vectors
scsi: ipr: Fix runaway IRQs when falling back from MSI to LSI
scsi: dpt_i2o: double free on error path
scsi: cxlflash: Migrate scsi command pointer to AFU command
scsi: cxlflash: Migrate IOARRIN specific routines to function pointers
scsi: cxlflash: Cleanup queuecommand()
scsi: cxlflash: Cleanup send_tmf()
scsi: cxlflash: Remove AFU command lock
scsi: cxlflash: Wait for active AFU commands to timeout upon tear down
scsi: cxlflash: Remove private command pool
...
Add phy clock enable code to phy_power_on/off callbacks, and
remove explicit calls to enable these phy clocks from the
ufs-qcom hcd driver.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a dummy function for phy_reset in case the CONFIG_GENERIC_PHY
is disabled.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The only use for this is for solving a hardware design problem in
usb of Rockchip RK3288.
Signed-off-by: Randy Li <ayaka@soulik.info>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The initial use for this is for PHYs that have a mode related to USB OTG.
There are several SoCs (e.g. TI OMAP and DA8xx) that have a mode setting
in the USB PHY to override OTG VBUS and ID signals.
Of course, the enum can be expaned in the future to include modes for
other types of PHYs as well.
Suggested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: David Lechner <david@lechnology.com>
Add a new driver for the XUSB pad controller found on NVIDIA Tegra SoCs.
This hardware block used to be exposed as a pin controller, but it turns
out that this isn't a good fit. The new driver and DT binding much more
accurately describe the hardware and are more flexible in supporting new
SoC generations.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to more flexibly support device tree bindings, allow drivers to
override the container of the child nodes. By default the device node of
the PHY provider is assumed to be the parent for children, but bindings
may decide to add additional levels for better organization.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Deprecate using phy-omap-control driver to power on/off the PHY,
and use *syscon* framework to do the same. This handles
powering on/off the PHY for the USB2 PHYs used in various TI SoCs.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
*) new Broadcom SATA3 PHY driver for Broadcom STB SoCs
*) new phy API to get PHY by index which is used in EHCI and
OHCI controller drivers
*) support specifying supply at port level used for multi-port PHYs
*) sparse warning fixes in miphy PHYs
*) fix pm_runtime issues in twl4030 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPk6
-----END PGP SIGNATURE-----
Merge tag 'phy-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.2 merge window
*) new Broadcom SATA3 PHY driver for Broadcom STB SoCs
*) new phy API to get PHY by index which is used in EHCI and
OHCI controller drivers
*) support specifying supply at port level used for multi-port PHYs
*) sparse warning fixes in miphy PHYs
*) fix pm_runtime issues in twl4030 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The sunxi otg phy has a bug where it wrongly detects a high speed squelch
when reset on the root port gets de-asserted with a lo-speed device.
The workaround for this is to disable squelch detect before de-asserting
reset, and re-enabling it after the reset de-assert is done. Add a sunxi
specific phy function to allow the sunxi-musb glue to do this.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some generic drivers, such as ehci, may use multiple phys and for such
drivers referencing phy(s) by name(s) does not make sense. Instead of
inventing new naming schemes and using custom code to iterate through them,
such drivers are better of using nameless phy bindings and using this newly
introduced API to iterate through them.
Signed-off-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
[kishon@ti.com: fix compilation errors]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is the usual grab bag of driver updates (hpsa, storvsc, mp2sas,
megaraid_sas, ses) plus an assortment of minor updates. There's also an
update to ufs which adds new phy drivers and finally a new logging
infrastructure for SCSI.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJU2Ty5AAoJEDeqqVYsXL0M9rAH/1xNpAxXuxQq+dW5Z+uOaX60
5RRIu7/xA1HEfzkT5FTHrolmogDjVqawu4PZS66iHDeo05RBVUlbTA8qCK+MlRcN
U6s0cLEw59eH3EaCfOGuYp/MnbhuV0eNxe0btmqJIQwuW3+gwZKGJdOq6LS2YasJ
k/DyIBVmkJAVsN56vm9q2vbtcZp+Bg+ngqBS+SC4TF7vV1WCtFmS6yaUf62PYW3D
+Irx37qHZntDR5wdw3dsuKDi5U8bl6myPjaVLnVJqg/WIF9RlCkjk5xpWT99AmVO
NmtYQxLLBlAQ5K+sIlBUwxZe+8q1l+Aj4TTmJHAfFtyfp25s7JR9I6/QtOyC5Kw=
=odol
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (hpsa, storvsc, mp2sas,
megaraid_sas, ses) plus an assortment of minor updates.
There's also an update to ufs which adds new phy drivers and finally a
new logging infrastructure for SCSI"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (114 commits)
scsi_logging: return void for dev_printk() functions
scsi: print single-character strings with seq_putc
scsi: merge consecutive seq_puts calls
scsi: replace seq_printf with seq_puts
aha152x: replace seq_printf with seq_puts
advansys: replace seq_printf with seq_puts
scsi: remove SPRINTF macro
sg: remove an unused variable
hpsa: Use local workqueues instead of system workqueues
hpsa: add in P840ar controller model name
hpsa: add in gen9 controller model names
hpsa: detect and report failures changing controller transport modes
hpsa: shorten the wait for the CISS doorbell mode change ack
hpsa: refactor duplicated scan completion code into a new routine
hpsa: move SG descriptor set-up out of hpsa_scatter_gather()
hpsa: do not use function pointers in fast path command submission
hpsa: print CDBs instead of kernel virtual addresses for uncommon errors
hpsa: do not use a void pointer for scsi_cmd field of struct CommandList
hpsa: return failed from device reset/abort handlers
hpsa: check for ctlr lockup after command allocation in main io path
...
This change adds a support for a 20nm qcom-ufs phy that is required in
platforms that use ufs-qcom controller.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Prior to DRA74x silicon rev 1.1, pcie_pcs register bits 8-15 and bits 16-23
were used to configure RC delay count for phy1 and phy2 respectively.
phyid was used as index to distinguish the phys and to configure the delay
values appropriately.
As of DRA74x silicon rev 1.1, pcie_pcs register definition has changed.
Bits 16-23 are used to configure delay values for *both* phy1 and phy2.
Hence phyid is no longer required.
So, drop id field from ti_pipe3 structure and its subsequent references
for configuring pcie_pcs register.
Also, pcie_pcs register now needs to be configured with delay value of 0x96
at bit positions 16-23. See register description of CTRL_CORE_PCIE_PCS in
ARM572x TRM, SPRUHZ6, October 2014, section 18.5.2.2, table 18-1804.
This is needed to ensure Gen2 cards are enumerated consistently.
DRA72x silicon behaves same way as DRA74x rev 1.1 as far as this functionality
is considered.
Test results on DRA74x and DRA72x EVMs:
Before patch
------------
DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to
silicon errata)
DRA74x ES 1.1: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect
programming of register
DRA72x: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect
programming of register
After patch
-----------
DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to
silicon errata)
DRA74x ES 1.1: Gen1 cards work, Gen2 cards work consistently.
DRA72x: Gen1 and Gen2 cards enumerate consistently.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The users of the old method are now converted to the new one.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[ kishon@ti.com : made phy-berlin-usb.c and phy-miphy28lp.c to use the updated
devm_phy_create API.]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Separates registration of the phy and the lookup. The method
is copied from clkdev.c,
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This makes to_phy() macro work with other variable names
besides "dev".
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In case of multi-phy PHY providers, each PHY should be modeled as a sub
node of the PHY provider. Then each PHY will have a different node pointer
(node pointer of sub node) than that of PHY provider. Added this provision
in the PHY core.
Also fixed all drivers to use the updated API.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Some PHYs can be powered by an external power regulator.
e.g. USB_HS PHY on DRA7 SoC. Make the PHY core support a
power regulator.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
8-bit delay value (0xF1) is required for GEN2 devices to be enumerated
consistently. Added an API to be called from PHY drivers to set this delay
value and called it from PIPE3 driver to set the delay value.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
This fixes a regression on Keystone 2 platforms caused by patch
57303488cd
"usb: dwc3: adapt dwc3 core to use Generic PHY Framework" which adds
optional support of generic phy in DWC3 core.
On Keystone 2 platforms the USB is not working now because
CONFIG_GENERIC_PHY isn't set and, as result, Generic PHY APIs stubs
return -ENOSYS always. The log shows:
dwc3 2690000.dwc3: failed to initialize core
dwc3: probe of 2690000.dwc3 failed with error -38
Hence, fix it by making NULL a valid phy reference in Generic PHY
APIs stubs in the same way as it was done by the patch
04c2facad8 "drivers: phy: Make NULL
a valid phy reference".
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename struct omap_control_usb to struct omap_control_phy since it can
be used to control PHY of USB, SATA and PCIE. Also move the driver and
include files under *phy* and made the corresponding changes in the users
of phy-omap-control.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Enable the dra7x errata workaround for false disconnect problem
with USB2PHY. False disconnects were detected with some of the devices.
Reduce the sensitivity of the disconnect logic within the USB2PHY subsystem
to enusre these false disconnects are not registered.
[george.cherian@ti.com]
While at that, pass proper flags for each SoC's. This is a common driver
used across OMAP4,OMAP5,DRA7xx and AM437x USB2PHY.
False disconnect workaround is currently applicable for only DRA7x.
Signed-off-by: Austin Beam <austinbeam@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adapt phy-omap-usb2 driver for AM437x.
- Add new comaptible "ti,am437x-usb2" for AM437x
- Pass proper data to differentiate AM437x and others.
- AM437x doesnot support set_vbus and start_srp.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adding devm_of_phy_get will allow to get phys by supplying a
pointer to the struct device_node instead of struct device.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Previously the of_phy_get function took a struct device * and
was declared static. It was impossible to call it from
another driver and thus it was impossible to get phy defined
for a given node. The old function was renamed to _of_phy_get
and was left for internal use. of_phy_get function was added
and it was exported. The function enables to get a phy for
a given device tree node.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
No functional change. Moved omap_usb.h from linux/usb/ to linux/phy/.
Also removed the unused members of struct omap_usb (after phy-omap-pipe3
started using it's own header file)
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add devm_phy_optional_get and phy_optional_get, which should be used
when the phy is optional. They does not return an error when the phy
does not exist, rather they returns NULL, which is considered as a valid
phy, but results in NOPs when used with the consumer API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This adds a pair of APIs that allows the generic PHY subsystem to
provide information on the PHY bus width. The PHY provider driver may
use phy_set_bus_width() to set the bus width that the PHY supports.
The controller driver may then use phy_get_bus_width() to fetch the
PHY bus width in order to properly configure the controller.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The PHY framework provides a set of APIs for the PHY drivers to
create/destroy a PHY and APIs for the PHY users to obtain a reference to the
PHY with or without using phandle. For dt-boot, the PHY drivers should
also register *PHY provider* with the framework.
PHY drivers should create the PHY by passing id and ops like init, exit,
power_on and power_off. This framework is also pm runtime enabled.
The documentation for the generic PHY framework is added in
Documentation/phy.txt and the documentation for dt binding can be found at
Documentation/devicetree/bindings/phy/phy-bindings.txt
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dov Levenglick