Some BIOS on Toshiba machines corrupt the DSDT, so add a new
boot option acpi=copy_dsdt to workaround it.
Add warning message to ask users to use this option if corrupt DSDT detected.
Also build a DMI blacklist to check it and automatically copy DSDT.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move initialization of DSDT pointer. Emit address of DSDT
in the dump of both table headers (good/bad DSDT).
Now handles the case where the root table can be reallocated,
which would invalidate the original pointer.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Optionally copy the entire DSDT to local memory (instead of
simply mapping it.) There are some BIOSs that corrupt or replace
the original DSDT, creating the need for this option. Default is
FALSE, do not copy the DSDT.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change adds support to detect a DSDT that has been corrupted
and/or replaced from outside the OS (by firmware). This is
typically catastrophic for the system, but has been seen on
some machines.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The original implementation only supported reading from a DataTable
region. However, some machines have been seen that actually write
to the ACPI table contained in such a region. This change adds
support for writing to a DataTable region.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When copying the root table to the new allocation, the length
used was incorrect. The new size was used instead of the current
table size, meaning too much data was copied.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Also split some long lines.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a problem with the AML Mutex handling function
acpi_ex_release_mutex where the function could fault under the very
rare condition when the interpreter has blocked, the interpreter
lock is released, the interpreter is then reentered via the
same thread, and attempts to acquire a mutex that was previously
acquired. FreeBSD report 140979.
http://www.freebsd.org/cgi/query-pr.cgi?pr=140979
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Always use 0x prefix for hex output, use %u for integer output
(all integers are unsigned.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change will enable debug object output via a global variable,
acpi_gbl_enable_aml_debug_object. This will help with remote machine
debugging. Also, moved all debug object support code to a new
file, exdebug.c. Entire debug object module can now be
configured out of the ACPICA build if desired.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI spec includes a provision for hardware to provide EDID via the
ACPI video extension. In the KMS world it's necessary for a way to obtain
this from within the kernel. Add a function that either returns the EDID
for the provided ACPI display ID or the first display of the provided type.
Also add support for ensuring that devices with legacy IDs are supported.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
access_bit_width field is u8 in ACPICA, thus 256 value written to it
becomes 0, causing divide by zero later.
Proper fix would be to remove access_bit_width at all, just because
we already have access_byte_width, which is access_bit_width / 8.
Limit access width to 64 bit for now.
https://bugzilla.kernel.org/show_bug.cgi?id=15749
fixes regression caused by the fix for:
https://bugzilla.kernel.org/show_bug.cgi?id=14667
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
There is a problem with the ACPI video resume routine that it's
executed before the GPU that may be accessed by it. To fix this
issue, move the ACPI video resume to a power management notifier,
so that's executed after resuming all devices, including the GPU.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15096, which is
a listed regression from 2.6.31.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
By default, ACPI resource conflict messages are logged at level
KERN_ERR. This is a rather high level for a message that is more a
warning than an indication of a real kernel error. Also, KERN_ERR level
messages can appear over some boot splash screens, and this message is
not serious enough to warrant such treatment. Thus, the log level has
been reduced to KERN_WARNING.
[lenb changed to KERN_WARNING rather than all the way to KERN_INFO]
Also, cleanup message to use %pR resource printing format.
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Calling kobject_uevent() directly is a layering violation. In
particular, it means we'll miss updating the generic LED trigger.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Disabling CONFIG_ACPI_SYSFS_POWER changes the behaviour of
acpi_battery_update(). It will call acpi_battery_get_info()
even if the battery is not present. I haven't noticed this
causing any problem, but it does look like a bad idea.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
I have a machine here that's sending 0xD1 notifications on the video
device once every second or so. I have no idea why (it's a prototype,
it may be broken), but sending KEY_UNKNOWN is unhelpful and results in
the console becoming unusable. Let's not report keys unless we have
something useful to say about them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
pxms are mapped to low node ids to maintain generic kernel use of
functions such as pxm_to_node() that are used to determine device
affinity. Otherwise, there is no pxm-to-node and node-to-pxm matching
rule for x86_64 users of NUMA emulation where a single pxm may be bound
to multiple NUMA nodes.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The acpi_pci_root structure contains all the individual items (acpi_device,
domain, bus number) we pass to pci_acpi_scan_root(), so just pass the
single acpi_pci_root pointer directly.
This will make it easier to add _CBA support later. For _CBA, we need the
entire downstream bus range, not just the base bus number. We have that in
the acpi_pci_root structure, so passing the pointer makes it available to
the arch-specific code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously, we only saved the root bus number, i.e., the beginning of the
downstream bus range. We now support IORESOURCE_BUS resources, so this
patch uses that to keep track of both the beginning and the end of the
downstream bus range.
It's important to know both the beginning and the end for supporting _CBA
(see PCI Firmware spec, rev 3.0, sec 4.1.3) and so we know the limits for
any possible PCI bus renumbering (we can't renumber downstream buses to be
outside the bus number range claimed by the host bridge).
It's clear from the spec that the bus range is supposed to be in _CRS, but
if we don't find it there, we'll assume [_BBN - 0xFF] or [0 - 0xFF].
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously, we assumed the only Device object immediately below the root
was the \_SB Scope (which the ACPI CA treats as a Device), so we forced
the HID of all such objects to ACPI_BUS_HID ("LNXSYBUS").
However, there are DSDTs that supply root-level Device objects with _HIDs.
This patch makes us pay attention to those _HIDs and only add the synthetic
ACPI_BUS_HID for root-level objects that do not supply their own _HID.
For example, this DSDT: https://bugzilla.kernel.org/show_bug.cgi?id=15605
contains:
Scope (_SB) {
...
}
Device (AMW0) {
Name (_HID, EisaId ("PNP0C14"))
...
}
and we should use "PNP0C14" for the AMW0 device, not "LNXSYBUS".
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
On some old IBM workstations and desktop computers, the BIOS presents in the
DSDT an SMBus object that is missing the HID identifier that the i2c-scmi
driver looks for. Modify the ACPI device scan code to insert the missing HID
if it finds an IBM system with such an object.
Affected machines: IntelliStation Z20/Z30. Note that the i2c-i801 driver no
longer works on these machines because of ACPI resource conflicts.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
acpi_ev_enable_gpe() should enable the GPE at the hardware level
regardless of the value of the GPE's runtime reference counter.
There are only two callers of acpi_ev_enable_gpe(), acpi_enable_gpe()
and acpi_set_gpe(). The first one checks the GPE's runtime
reference counter itself and only calls acpi_ev_enable_gpe() if it's
equal to one, and the other one is supposed to enable the GPE
unconditionally (if called with ACPI_GPE_ENABLE).
This change fixes the problem in acpi_enable_wakeup_device() where
the GPE will not be enabled for wakeup if it's runtime reference
counter is zero, which is a regression from 2.6.33.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Robert Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There may be multiple ACPI dock devices exist in ACPI namespace
and we should probe all of them.
http://bugzilla.kernel.org/show_bug.cgi?id=15521
CC: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Values such as max_brightness should be set before backlights are
registered, but the current API doesn't allow that. Add a parameter to
backlight_device_register and update drivers to ensure that they
set this correctly.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
There's no real need for a pointer to the MADT to be global. The only
function who uses it is map_madt_entry.
This allows us to remove some more ugly #ifdefs.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Un-nest the if statements for readability.
Remove comments that re-state the obvious.
Change the control flow so that we no longer need a temp variable.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Untangle the nested if conditions to make this function look
more similar to the other map_*apic_id() functions.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Untangle the if() statement a little for readability.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now that the early _PDC evaluation path knows how to correctly
evaluate _PDC on only physically present processors, there's no
need for the processor driver to evaluate it later when it loads.
To cover the hotplug case, push _PDC evaluation down into the
hotplug paths.
Cc: x86@kernel.org
Cc: Tony Luck <tony.luck@intel.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now that we check for physically present processors before blindly
evaluating _PDC, we no longer need to maintain a DMI opt-in table
nor a kernel param.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Detect if a processor is physically present before evaluating _PDC.
We want this because some BIOS will provide a _PDC even for processors
that are not present. These bogus _PDC methods then attempt to load
non-existent tables, which causes problems.
Avoid those bogus landmines.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enumerating processors (via MADT/_MAT) belongs in the processor core,
which is always built-in, rather than living in the processor driver
which may not be built.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rename static get_cpu_id() to acpi_get_cpuid() and export it.
This change also gives us an opportunity to remove the
#ifndef CONFIG_SMP from processor_driver.c and into a header file
where it properly belongs.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We've renamed the old processor_core.c to processor_driver.c, to
convey the idea that it can be built modular and has driver-like
bits.
Now let's re-create a processor_core.c for the bits needed
statically by the rest of the kernel. The contents of processor_pdc.c
are a good starting spot, so let's just rename that file and
complete our three card monte.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI processor driver can be built as a module. But it has
pieces of code that should always be built statically into the
kernel.
The plan is for processor_core.c to contain the static bits while
processor_driver.c contains the module-like bits.
Since the bulk of the code in the current processor_core.c is
module-like, first step is to rename the file to processor_driver.c
Next step will re-create processor_core.c and cherry-pick out
the static bits.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi=ht was important in 2003 -- before ACPI was
universally deployed and enabled by default in
the major Linux distributions.
At that time, there were a fair number of people who
or chose to, or needed to, run with acpi=off,
yet also wanted access to Hyper-threading.
Today we find that many invocations of "acpi=ht"
are accidental, and thus is it possible that it
is doing more harm than good.
In 2.6.34, we warn on invocation of acpi=ht.
In 2.6.35, we delete the boot option.
Signed-off-by: Len Brown <len.brown@intel.com>
Right now, if _BQC returns a value we don't understand we immediately
invalidate it. Change this behaviour so we only invalidate it if it
continues to give an invalid answer after we've already set a brightness.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
There is a race between resume from hibernation and the EC driver
that may result in restoring the hibernation image in the middle of
an EC transaction in progress, which in turn may lead to
unpredictable behavior of the platform.
To remove that race condition, add a helpers for suspending and
resuming EC transactions in a safe way to be executed by the ACPI
platform hibernate pre-restore and restore cleanup callbacks.
http://bugzilla.kernel.org/show_bug.cgi?id=14668
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
These are the non-static sysfs attributes that exist on
my test machine. Fix them to use sysfs_attr_init or
sysfs_bin_attr_init as appropriate. It simply requires
making a sysfs attribute present to see this. So this
is a little bit tedious but otherwise not too bad.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (25 commits)
x86: Fix out of order of gsi
x86: apic: Fix mismerge, add arch_probe_nr_irqs() again
x86, irq: Keep chip_data in create_irq_nr and destroy_irq
xen: Remove unnecessary arch specific xen irq functions.
smp: Use nr_cpus= to set nr_cpu_ids early
x86, irq: Remove arch_probe_nr_irqs
sparseirq: Use radix_tree instead of ptrs array
sparseirq: Change irq_desc_ptrs to static
init: Move radix_tree_init() early
irq: Remove unnecessary bootmem code
x86: Add iMac9,1 to pci_reboot_dmi_table
x86: Convert i8259_lock to raw_spinlock
x86: Convert nmi_lock to raw_spinlock
x86: Convert ioapic_lock and vector_lock to raw_spinlock
x86: Avoid race condition in pci_enable_msix()
x86: Fix SCI on IOAPIC != 0
x86, ia32_aout: do not kill argument mapping
x86, irq: Move __setup_vector_irq() before the first irq enable in cpu online path
x86, irq: Update the vector domain for legacy irqs handled by io-apic
x86, irq: Don't block IRQ0_VECTOR..IRQ15_VECTOR's on all cpu's
...
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: replace acpi_integer by u64
ACPICA: Update version to 20100121.
ACPICA: Remove unused uint32_struct type
ACPICA: Disassembler: Remove obsolete "Integer64" field in parse object
ACPICA: Remove obsolete ACPI_INTEGER (acpi_integer) type
ACPICA: Predefined name repair: fix NULL package elements
ACPICA: AcpiGetDevices: Eliminate unnecessary _STA calls
ACPICA: Update all ACPICA copyrights and signons to 2010
ACPICA: Update for new gcc-4 warning options
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (48 commits)
x86/PCI: Prevent mmconfig memory corruption
ACPI: Use GPE reference counting to support shared GPEs
x86/PCI: use host bridge _CRS info by default on 2008 and newer machines
PCI: augment bus resource table with a list
PCI: add pci_bus_for_each_resource(), remove direct bus->resource[] refs
PCI: read bridge windows before filling in subtractive decode resources
PCI: split up pci_read_bridge_bases()
PCIe PME: use pci_pcie_cap()
PCI PM: Run-time callbacks for PCI bus type
PCIe PME: use pci_is_pcie()
PCI / ACPI / PM: Platform support for PCI PME wake-up
ACPI / ACPICA: Multiple system notify handlers per device
ACPI / PM: Add more run-time wake-up fields
ACPI: Use GPE reference counting to support shared GPEs
PCI PM: Make it possible to force using INTx for PCIe PME signaling
PCI PM: PCIe PME root port service driver
PCI PM: Add function for checking PME status of devices
PCI: mark is_pcie obsolete
PCI: set PCI_PREF_RANGE_TYPE_64 in pci_bridge_check_ranges
PCI: pciehp: second try to get big range for pcie devices
...
To fix a bug and address the reviewers' comments regarding the ACPI
GPE refcounting patch, do the following additional changes:
o Remove the second argument of acpi_ev_enable_gpe(),
'write_to_hardware', because it is not necessary any more.
o Add the "bad parameter" test against 'type' in
acpi_enable_gpe() and acpi_disable_gpe().
o Make acpi_enable_gpe() only check 'status' for runtime GPEs if
acpi_ev_enable_gpe() was actually called.
o Make acpi_disable_gpe() return 'status' returned by
acpi_ev_disable_gpe() and fix a bug where ACPI_GPE_TYPE_WAKE
and ACPI_GPE_TYPE_RUNTIME were exchanged by mistake.
o Add comments explaining why acpi_set_gpe() is used by the ACPI EC
driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The main benefit of using ACPI host bridge window information is that
we can do better resource allocation in systems with multiple host bridges,
e.g., http://bugzilla.kernel.org/show_bug.cgi?id=14183
Sometimes we need _CRS information even if we only have one host bridge,
e.g., https://bugs.launchpad.net/ubuntu/+source/linux/+bug/341681
Most of these systems are relatively new, so this patch turns on
"pci=use_crs" only on machines with a BIOS date of 2008 or newer.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
V2: Corrected integer/long conversion.
Some BIOSes return a negative value for the critical trip point.
Especially since Windows 2006...
We currently invalidate the whole thermal zone in this case.
But it may still be needed for cooling, also without critical
trip point.
This patch invalidates the critical trip point if no _CRT
function is found or if it returns negative values, but does
not invalidate the whole thermal zone in this case.
Reference: http://bugzilla.novell.com/show_bug.cgi?id=531547
Signed-off-by: Thomas Renninger <trenn@suse.de>
Tested-by: clarkt@cnsp.com
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Although the majority of PCI devices can generate PMEs that in
principle may be used to wake up devices suspended at run time,
platform support is generally necessary to convert PMEs into wake-up
events that can be delivered to the kernel. If ACPI is used for this
purpose, PME signals generated by a PCI device will trigger the ACPI
GPE associated with the device to generate an ACPI wake-up event that
we can set up a handler for, provided that everything is configured
correctly.
Unfortunately, the subset of PCI devices that have GPEs associated
with them is quite limited. The devices without dedicated GPEs have
to rely on the GPEs associated with other devices (in the majority of
cases their upstream bridges and, possibly, the root bridge) to
generate ACPI wake-up events in response to PME signals from them.
Add ACPI platform support for PCI PME wake-up:
o Add a framework making is possible to use ACPI system notify
handlers for run-time PM.
o Add new PCI platform callback ->run_wake() to struct
pci_platform_pm_ops allowing us to enable/disable the platform to
generate wake-up events for given device. Implemet this callback
for the ACPI platform.
o Define ACPI wake-up handlers for PCI devices and PCI root buses and
make the PCI-ACPI binding code register wake-up notifiers for all
PCI devices present in the ACPI tables.
o Add function pci_dev_run_wake() which can be used by PCI drivers to
check if given device is capable of generating wake-up events at
run time.
Developed in cooperation with Matthew Garrett <mjg@redhat.com>.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently it only is possible to install one system notify handler
per namespace node, but this is not enough for PCI run-time power
management, because we need to install power management notifiers for
devices that already have hotplug notifiers installed. While in
principle this could be handled at the PCI level, that would be
suboptimal due to the way in which the ACPI-based PCI hotplug code is
designed.
For this reason, modify ACPICA so that it is possible to install more
than one system notify handler per namespace node. Namely, make
acpi_install_notify_handler(), acpi_remove_notify_handler() and
acpi_ev_notify_dispatch() use a list of system notify handler objects
associated with a namespace node.
Make acpi_remove_notify_handler() call acpi_os_wait_events_complete()
upfront to avoid a situation in which concurrent instance of
acpi_remove_notify_handler() removes the handler from under us while
we're waiting for the event queues to flush.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the run_wake flag to mark all devices for which run-time wake-up
events may be generated by the platform. Introduce a new wake-up
flag, always_enabled, for marking devices that should be permanently
enabled to generate run-time events. Also, introduce a reference
counter for run-wake devices and a function that will initialize all
of the run-time wake-up fields for given device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ACPI GPEs may map to multiple devices. The current GPE interface
only provides a mechanism for enabling and disabling GPEs, making
it difficult to change the state of GPEs at runtime without extensive
cooperation between devices.
Add an API to allow devices to indicate whether or not they want
their device's GPE to be enabled for both runtime and wakeup events.
Remove the old GPE type handling entirely, which gets rid of various
quirks, like the implicit disabling with GPE type setting. This
requires a small amount of rework in order to ensure that non-wake
GPEs are enabled by default to preserve existing behaviour.
Based on patches from Matthew Garrett <mjg@redhat.com>.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ACPI deep C-state entry had a long standing bug/missing feature, wherein we were sending
resched IPIs when an idle CPU is in mwait based deep C-state. Only mwait based C1 was using
the write to the monitored address to wake up mwait'ing CPU.
This patch changes the code to retain TS_POLLING bit if we are entering an mwait based
deep C-state.
The patch has been verified to reduce the number of resched IPIs in general and also
improves the performance/power on workloads with low system utilization (i.e., when mwait based
deep C-states are being used).
Fixes "netperf ~50% regression with 2.6.33-rc1, bisect to 1b9508f"
http://marc.info/?l=linux-kernel&m=126441481427331&w=4
Reported-by: Lin Ming <ming.m.lin@intel.com>
Tested-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI spec says (11.5 Thermal Zone Interface Requirements):
A thermal zone must contain at least one trip point
(critical, near critical, active, or passive)
Check this once at init time.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Tested-by: clarkt@cnsp.com
Signed-off-by: Len Brown <len.brown@intel.com>
Earlier, Ingo Molnar posted a patch to make it so that the kernel would avoid
reading _PPC on his broken T60. Unfortunately, it seems that with Thomas
Renninger's patch last July to eliminate _PPC evaluations when the processor
driver loads, the kernel never actually reads _PPC at all! This is problematic
if you happen to boot your non-T60 computer in a state where the BIOS _wants_
_PPC to be something other than zero.
So, put the _PPC evaluation back into acpi_processor_get_performance_info if
ignore_ppc isn't 1.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We broke "acpi=ht" in 2.6.32 by disabling MADT parsing
for acpi=disabled. e5b8fc6ac1
This also broke systems which invoked acpi=ht via DMI blacklist.
acpi=ht is a really ugly hack,
but restore it for those that still use it.
http://bugzilla.kernel.org/show_bug.cgi?id=14886
Signed-off-by: Len Brown <len.brown@intel.com>
On x86, before prefill_possible_map(), nr_cpu_ids will be NR_CPUS aka
CONFIG_NR_CPUS.
Add nr_cpus= to set nr_cpu_ids. so we can simulate cpus <=8 are installed on
normal config.
-v2: accordging to Christoph, acpi_numa_init should use nr_cpu_ids in stead of
NR_CPUS.
-v3: add doc in kernel-parameters.txt according to Andrew.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-34-git-send-email-yinghai@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Tony Luck <tony.luck@intel.com>
Add __percpu sparse annotations to places which didn't make it in one
of the previous patches. All converions are trivial.
These annotations are to make sparse consider percpu variables to be
in a different address space and warn if accessed without going
through percpu accessors. This patch doesn't affect normal builds.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Neil Brown <neilb@suse.de>
Since the rewrite of the CPU idle governor in 2.6.32, two laptops have
surfaced where the BIOS advertises a C2 power state, but for some reason
this state is not functioning (as verified in both cases by powertop
before the patch in .32).
The old governor had the accidental behavior that if a non-working state
was chosen too many times, it would end up falling back to C1. The new
governor works differently and this accidental behavior is no longer
there; the result is a high temperature on these two machines.
This patch adds these 2 machines to the DMI table for C state anomalies;
by just not using C2 both these machines are better off (the TSC can be
used instead of the pm timer, giving a performance boost for example).
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=14742
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Reported-by: <akwatts@ymail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit fe06fba2 (ACPI: dock: add struct dock_station * directly
to platform device data) changed dock_add() to use the
platform_device_register_data() API.
We passed that interface a stack variable, which is kmemdup'ed
and assigned to the device's platform_data pointer.
Unfortunately, whatever random garbage is in the stack variable
gets coped during the kmemdup, and that leads to broken behavior.
Explicitly zero out the structure before passing it to the API.
This fixes the T41 docking button issue:
http://bugzilla.kernel.org/show_bug.cgi?id=15000
Cc: stable@kernel.org
Reported-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
trivial, leftover from my NULL pointer dereference patch which got
'superseded' by commit fbc3be2
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Dan's list contains:
drivers/acpi/processor_throttling.c +1139 acpi_processor_get_throttling_info(11) warning: variable derefenced before check 'pr'
acpi_processor_get_throttling_info() is never called with pr == NULL.
[ bart: the potential NULL pointer dereference was finally fixed in
(much later than mine) commit 5cfa245 but my patch is still valid ]
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Roel found a logic issue in the #if 0 acpi_evaluate_string():
- || (element->type != ACPI_TYPE_BUFFER)
+ && (element->type != ACPI_TYPE_BUFFER)
delete the dead code.
pointed-out-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some string messages misspell "separate"; this fixes them. No change in
functionality.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Callers (acpi_memhotplug.c, dock.c and others) check for the return
value of acpi_bus_add() and assume a valid device was returned in
case zero was returned.
Thus return -ENODEV if no device was found in acpi_bus_scan and
propagate this through acpi_bus_add and acpi_bus_start.
Also remove a confusing comment in acpiphp_glue.c, acpi_bus_scan
will and cannot invoke if acpi_bus_add returns no valid device.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If acpi_bus_add does not return a device and it's passed
to acpi_bus_start, bad things will happen:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffff8128402d>] acpi_bus_start+0x14/0x24
...
[<ffffffffa008977a>] acpiphp_bus_add+0xba/0x130 [acpiphp]
[<ffffffffa008aa72>] enable_device+0x132/0x2ff [acpiphp]
[<ffffffffa0089b68>] acpiphp_enable_slot+0xb8/0x130 [acpiphp]
[<ffffffffa0089df7>] handle_hotplug_event_func+0x87/0x190 [acpiphp]
Next patch would make this NULL pointer check obsolete, but
better having one more than one missing...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_integer is now obsolete and removed from the ACPICA code base,
replaced by u64.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If we evaluate _PDC in the early path, we do not want to evaluate
it again when the processor driver is loaded.
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Allow platforms not listed in DMI table
to opt-in and evaluate _PDC early.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This field is no longer needed. The "Integer" field is 64 bit
and is sufficient.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This type was introduced as the code was migrated from ACPI 1.0
(with 32-bit AML integers) to ACPI 2.0 (with 64-bit integers). It
is now obsolete and this change removes it from the ACPICA code
base, replaced by u64. The original typedef has been retained
for now for compatibility with existing device driver code.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
For the predefined methods that return fixed-length packages
(or subpackages), attempt repair for a NULL element. Create an
Integer of value 0, a NULL String, or a zero-length buffer as
appropriate.
http://www.acpica.org/bugzilla/show_bug.cgi?id=818
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In the case where a specific _HID is requested, do not run _STA
until a _HID match is found. This eliminates potentially dozens
of _STA calls during a search for a particular device/HID.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add 2010 copyright to all module headers and signons, including
the Linux header. This affects virtually every file in the ACPICA
core subsystem, iASL compiler, and all utilities.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added several new options for the gcc-4 generation, and updated
the source accordingly. This includes some code restructuring to
eliminate unreachable code, elimination of some gotos, elimination
of unused return values, and some additional casting.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
no functional change -- cleanup only.
acpi_processor_power_verify_c2() was nearly empty due to a previous patch,
so expand its remains into its one caller and delete it.
Signed-off-by: Len Brown <len.brown@intel.com>
Do for C3 what the previous patch did for C2.
The C2 patch was in response to a highly visible
and multiply reported C-state/turbo failure,
while this change has no bug report in-hand.
This will enable C3 in Linux on systems where BIOS
overstates C3 latency in _CST. It will also enable
future systems which may actually have C3 > 1000usec.
Linux has always ignored ACPI BIOS C3 with exit latency > 1000 usec,
and the ACPI spec is clear that is correct FADT-supplied C3.
However, the ACPI spec explicitly states that _CST-supplied C-states
have no latency limits.
So move the 1000usec C3 test out of the code shared
by FADT and _CST code-paths, and into the FADT-specific path.
Signed-off-by: Len Brown <len.brown@intel.com>
Linux has always ignored ACPI BIOS C2 with exit latency > 100 usec,
and the ACPI spec is clear that is correct FADT-supplied C2.
However, the ACPI spec explicitly states that _CST-supplied C-states
have no latency limits.
So move the 100usec C2 test out of the code shared
by FADT and _CST code-paths, and into the FADT-specific path.
This bug has not been visible until Nehalem, which advertises
a CPU-C2 worst case exit latency on servers of 205usec.
That (incorrect) figure is being used by BIOS writers
on mobile Nehalem systems for the AC configuration.
Thus, Linux ignores C2 leaving just C1, which is
saves less power, and also impacts performance
by preventing the use of turbo mode.
http://bugzilla.kernel.org/show_bug.cgi?id=15064
Tested-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
resource->domain_devices can be double kfree()'d in a couple of places.
Fix this by setting num_domain_devices = 0 after the kfree().
Coverity CID: 13356, 13355, 13354
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 78f1699 (ACPI: processor: call _PDC early) blindly walks
the namespace and calls _PDC on every processor object it finds.
This change may cause issues on platforms that declare dummy
values for SSDTs on non-present processors (disabled in MADT).
When we call _PDC and dynamically attempt to execute the AML
Load() op on these dummy SSDTs, there's no telling what might
happen.
Rather than finding every platform that has bogus SSDTs, restrict
early _PDC calls to platforms that are known to need early
evaluation of _PDC.
This is a minimal, temporary fix (given the context of the
current release cycle). A real solution of checking the MADT for
non-present processors will be written for the next merge window.
References:
http://bugzilla.kernel.org/show_bug.cgi?id=14710http://bugzilla.kernel.org/show_bug.cgi?id=14954
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When CONFIG_ACPI_SYSFS_POWER=n and CONFIG_ACPI_PROCFS_POWER=n, then
we're warned by the following warning:
drivers/acpi/sbs.c: In function `acpi_battery_remove':
drivers/acpi/sbs.c:825: warning: unused variable `battery'
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The ids field of the struct acpi_driver is constant in <linux/acpi/acpi_bus.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang introduced acpi_early_processor_set_pdc() in commit:
ACPI: processor: call _PDC early
78f1699659
But this results in a section mismatch:
WARNING: drivers/acpi/acpi.o(.text+0xa9c1): Section mismatch in reference from the
function acpi_early_processor_set_pdc() to the variable .cpuinit.data:processor_idle_dmi_table
The function acpi_early_processor_set_pdc() references
the variable __cpuinitdata processor_idle_dmi_table.
This is often because acpi_early_processor_set_pdc lacks a __cpuinitdata
annotation or the annotation of processor_idle_dmi_table is wrong.
The only caller of acpi_early_processor_set_pdc() is acpi_bus_init() which
is an "__init" function. So the correct fix here is to mark
acpi_early_processor_set_pdc() "__init" too.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The struct seq_file 'private' member is a void *, the cast is not needed.
Also, remove an extra whitespace line.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If the BIOS pokes the system-wide OSC bits to see if Linux
supports evaluating _OST after a _PPC change notification,
answer yes.
Also, fix an oversight where we neglected to set the OSC
bit advertising processor aggregator device support
when acpi-pad is compiled as a module.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Merge of poll and irq modes accelerated EC transaction, so
that keyboard starts to suffer again. Add msleep(1) into
transaction path for the storm to allow keyboard controller
to do its job.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=14747
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
SBS transactions should happen in Notify work queue, to not create
a dead lock with GPE execution accessing SBS devices.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Processor Clocking Control (PCC) is an interface between the BIOS and OSPM.
Based on the server workload, OSPM can request what frequency it expects
from a logical CPU, and the BIOS will achieve that frequency transparently.
This patch introduces driver support for PCC. OSPM uses the PCC driver to
communicate with the BIOS via the PCC interface.
There is a Documentation file that provides a link to the PCC
Specification, and also provides a summary of the PCC interface.
Currently, certain HP ProLiant platforms implement the PCC interface. However,
any platform whose BIOS implements the PCC Specification, can utilize this
driver.
V2 --> V1 changes (based on Dominik's suggestions):
- Removed the dependency on CPU_FREQ_TABLE
- "cpufreq_stats" will no longer PANIC. Actually, it will not load anymore
because it is not applicable.
- Removed the sanity check for target frequency in the ->target routine.
NOTE: A patch to sanitize the target frequency requested by "ondemand" is
needed to ensure that the target freq < policy->min.
Can this driver be queued up for the 2.6.33 tree?
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Some buggy BIOS exports multiple ACPI video bus devices for the same
VGA controller, and multiple backlight control methods as well.
This messes up the ACPI video backlight control.
http://bugzilla.kernel.org/show_bug.cgi?id=13577
With this patch applied, only the FIRST ACPI video bus device
under a PCI device node is bind to ACPI video driver by default.
If the first ACPI video bus device doesn't work well, we can use
video.allow_duplicates=1 to go back to the old behavior.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There are some fixes listed below:
1. When met a bogus BIOS, the return value of cpu number maybe is
a negative value so that acpi_pad_pur get an unexpected result.
2. the return value of function acpi_pad_idle_cpus is useless.
3. enhance the process of create_power_saving_task/destroy_power_saving_task
4. Add more error checks when evaluating _PUR object.
5. one typo fix
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce kernel parameter acpi_sleep=sci_force_enable
some laptop requires SCI_EN being set directly on resume,
or else they hung somewhere in the resume code path.
We already have a blacklist for these laptops but we still need
this option, especially when debugging some suspend/resume problems,
in case there are systems that need this workaround and are not yet
in the blacklist.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
backlight_device_register may return an ERR_PTR
value rather than a valid pointer.
Problem found by Julia Lawall, properly fixed by Zhang Rui.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Len Brown <len.brown@intel.com>
AML code always sends notifications to ACPI video device,
even if we disable the ACPI backlight control by using
boot option "acpi_backlight=vendor".
In this case we should not print any warning message.
http://bugzilla.kernel.org/show_bug.cgi?id=13671#c14
Sigend-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If the ACPI power state can be got both directly and indirectly,
we prefer to get it indirectly.
https://bugzilla.redhat.com/show_bug.cgi?id=531916 describes a
system with a _PSC method for the fan that always returns "on".
There's no benefit in us always requesting the state of the fan
when performing transitions - we want to do everything we can
to ensure that the fan turns on when it should do, not risk
hardware damage by believing the hardware when it tells us the
fan is already on. Given that the Leading Other OS(tm) works fine
on this machine, it seems likely that it behaves in much this way.
inspired-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split EC query handling into acknowledge and execution phase.
This allows much smaller pending query lattency and lowers chances
of EC going "wild" and losing events.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=14858
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Executing _OSC returns a buffer, which has an acpi object in it.
Don't directly returns the buffer, instead, we return the acpi object's
buffer. This fixes a regression since caller of acpi_run_osc expects
an acpi object's buffer returned.
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When calling _PDC, we really only need the handle to the processor
to call the method; we don't look at any other parts of the
struct acpi_processor * given to us.
In the early path, when we walk the namespace, we are given the
handle directly, so just pass it through to acpi_processor_set_pdc()
without stuffing it into a wasteful struct acpi_processor allocated
on the stack each time
This saves 2834 bytes of stack.
Update the interface accordingly.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We have the acpi_object_list * right there in acpi_processor_set_pdc()
so it doesn't seem necessary for an entire helper function just to
free it.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_processor_eval_pdc() really only needs a handle and an
acpi_object_list * to do its work.
No need to pass in a struct acpi_processor *, so let's be more specific
about what we want.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_processor_init_pdc() isn't really doing anything interesting
with the struct acpi_processor * parameter. Its real job is to allocate
the buffer for the _PDC bits.
So rename the function to acpi_processor_alloc_pdc(), and just return
the struct acpi_object_list * it's supposed to allocate.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The x86 and ia64 implementations of the function in $subject are
exactly the same.
Also, since the arch-specific implementations of setting _PDC have
been completely hollowed out, remove the empty shells.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The only thing arch-specific about calling _PDC is what bits get
set in the input obj_list buffer.
There's no need for several levels of indirection to twiddle those
bits. Additionally, since we're just messing around with a buffer,
we can simplify the interface; no need to pass around the entire
struct acpi_processor * just to get at the buffer.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Both x86 and ia64 initialize _PDC with mostly common bit settings.
Factor out the common settings and leave the arch-specific ones alone.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The x86 and ia64 implementations of arch_acpi_processor_init_pdc()
are almost exactly the same. The only difference is in what bits
they set in obj_list buffer.
Combine the boilerplate memory management code, and leave the
arch-specific bit twiddling in separate implementations.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
arch dependent helper function that tells us if we should attempt to
evaluate _PDC on this machine or not.
The x86 implementation assumes that the CPUs in the machine must be
homogeneous, and that you cannot mix CPUs of different vendors.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We discovered that at least one machine (HP Envy), methods in the DSDT
attempt to call external methods defined in a dynamically loaded SSDT.
Unfortunately, the DSDT methods we are trying to call are part of the
EC initialization, which happens very early, and the the dynamic SSDT
is only loaded when a processor _PDC method runs much later.
This results in namespace lookup errors for the (as of yet) undefined
methods.
Since Windows doesn't have any issues with this machine, we take it
as a hint that they must be evaluating _PDC much earlier than we are.
Thus, the proper thing for Linux to do should be to match the Windows
implementation more closely.
Provide a mechanism to call _PDC before we enable the EC. Doing so loads
the dynamic tables, and allows the EC to be enabled correctly.
The ACPI processor driver will still evaluate _PDC in its .add() method
to cover the hotplug case.
Resolves: http://bugzilla.kernel.org/show_bug.cgi?id=14824
Cc: ming.m.lin@intel.com
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix a win7 compability issue on Asus K50IJ.
Here is the _BCM method of this laptop:
Method (_BCM, 1, NotSerialized)
{
If (LGreaterEqual (OSFG, OSVT))
{
If (LNotEqual (OSFG, OSW7))
{
Store (One, BCMD)
Store (GCBL (Arg0), Local0)
Subtract (0x0F, Local0, LBTN)
^^^SBRG.EC0.STBR ()
...
}
Else
{
DBGR (0x0B, Zero, Zero, Arg0)
Store (Arg0, LBTN)
^^^SBRG.EC0.STBR ()
...
}
}
}
LBTN is used to store the index of the brightness level in the _BCL.
GCBL is a method that convert the percentage value to the index value.
If _OSI(Windows 2009) is not disabled, LBTN is stored a percentage
value which is surely beyond the end of _BCL package.
http://bugzilla.kernel.org/show_bug.cgi?id=14753
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Due to the merge of processor_start() (declared with __cpuinit) into
processor_add(), a section mismatch warning appears:
WARNING: drivers/built-in.o(.text+0x4d59d): Section mismatch in reference
from the function acpi_processor_add() to the function
.cpuinit.text:acpi_processor_power_init()
...
This patch fixes the warning by declaring processor_add() as __cpuinit
and also declares acpi_processor_add_fs() as __cpuinit as it is only
used in acpi_processor_add().
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
v2->v1:
.improve debug info as suggedted by Bjorn,Kenji
.API is using uuid string as suggested by Alexey
Add an API to execute _OSC. A lot of devices can have this method, so add a
generic API.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
I got following warning on ia64 box:
In function 'acpi_processor_power_verify':
642: warning: passing argument 2 of 'smp_call_function_single' from
incompatible pointer type
This smp_call_function_single() was introduced by a commit
f833bab87fca5c3ce13778421b1365845843b976:
> @@ -162,8 +162,9 @@
> pr->power.timer_broadcast_on_state = state;
> }
>
> -static void lapic_timer_propagate_broadcast(struct acpi_processor *pr)
> +static void lapic_timer_propagate_broadcast(void *arg)
> {
> + struct acpi_processor *pr = (struct acpi_processor *) arg;
> unsigned long reason;
>
> reason = pr->power.timer_broadcast_on_state < INT_MAX ?
> @@ -635,7 +636,8 @@
> working++;
> }
>
> - lapic_timer_propagate_broadcast(pr);
> + smp_call_function_single(pr->id, lapic_timer_propagate_broadcast,
> + pr, 1);
>
> return (working);
> }
The problem is that the lapic_timer_propagate_broadcast() has 2 versions:
One is real code that modified in the above commit, and the other is NOP
code that used when !ARCH_APICTIMER_STOPS_ON_C3:
static void lapic_timer_propagate_broadcast(struct acpi_processor *pr) { }
So I got warning because of !ARCH_APICTIMER_STOPS_ON_C3.
We really want to do nothing here on !ARCH_APICTIMER_STOPS_ON_C3, so
modify lapic_timer_propagate_broadcast() of real version to use
smp_call_function_single() in it.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/acpi/acpi_pad.c: In function 'power_saving_thread':
drivers/acpi/acpi_pad.c:103: warning: 'preferred_cpu' may be used uninitialized in this function
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed some stray whitespaces
Added whitespace when needed for legibility
Removed unneeded curly braces
Removed useless void casts
Removed unnecessary local variable initialization
Renamed variables to help out with 80-column fixes
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Instead of adding a (struct dock_station **) to our dock device's
platform data, we can add the (struct dock_station *) directly.
This change saves us some ugly casting and improves readability.
The cost of making this change is an extra 290 bytes of stack usage,
but this is an infrequently called code-path and unlikely to cause
the kernel to blow up.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move the call to platform_device_register_simple so that we do it
before allocating and initializing our struct dock_station.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We only use it in one spot, so it probably gets optimized out, but there's
still no need to use a global variable for this.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Lin Ming