In particular as-is it's not suited for multicore and mutiprocessors
systems where there is on guarantee that the counter are synchronized
or running from the same clock at all. This broke Sibyte and probably
others since the "[MIPS] Handle R4000/R4400 mfc0 from count register."
commit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The R4000 and R4400 have an errata where if the cp0 count register is read
in the exact moment when it matches the compare register no interrupt will
be generated.
This bug may be triggered if the cp0 count register is being used as
clocksource and the compare interrupt as clockevent. So a simple
workaround is to avoid using the compare for both facilities on the
affected CPUs.
This is different from the workaround suggested in the old errata documents;
at some opportunity probably the official version should be implemented
and tested. Another thing to find out is which processor versions
exactly are affected. I only have errata documents upto R4400 V3.0
available so for the moment the code treats all R4000 and R4400 as broken.
This is potencially a problem for some machines that have no other decent
clocksource available; this workaround will cause them to fall back to
another clocksource, worst case the "jiffies" source.
The LL / SC loops in __futex_atomic_op() have the usual fixups necessary
for memory acccesses to userspace from kernel space installed:
__asm__ __volatile__(
" .set push \n"
" .set noat \n"
" .set mips3 \n"
"1: ll %1, %4 # __futex_atomic_op \n"
" .set mips0 \n"
" " insn " \n"
" .set mips3 \n"
"2: sc $1, %2 \n"
" beqz $1, 1b \n"
__WEAK_LLSC_MB
"3: \n"
" .set pop \n"
" .set mips0 \n"
" .section .fixup,\"ax\" \n"
"4: li %0, %6 \n"
" j 2b \n" <-----
" .previous \n"
" .section __ex_table,\"a\" \n"
" "__UA_ADDR "\t1b, 4b \n"
" "__UA_ADDR "\t2b, 4b \n"
" .previous \n"
: "=r" (ret), "=&r" (oldval), "=R" (*uaddr)
: "0" (0), "R" (*uaddr), "Jr" (oparg), "i" (-EFAULT)
: "memory");
The branch at the end of the fixup code, it goes back to the SC
instruction, no matter if the fault was first taken by the LL or SC
instruction resulting in an endless loop which will only terminate if
the address become valid again due to another thread setting up an
accessible mapping and the CPU happens to execute the SC instruction
successfully which due to the preceeding ERET instruction of the fault
handler would only happen if UNPREDICTABLE instruction behaviour of the
SC instruction without a preceeding LL happens to favor that outcome.
But normally processes are nice, pass valid arguments and we were just
getting away with this.
Thanks to Kaz Kylheku <kaz@zeugmasystems.com> for providing the original
report and a test case.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A new born thread starts execution not in schedule but rather in
ret_from_fork which results in it bypassing the part of the code to
load a new context written in C which are the DSP context and the
userlocal register which Linux uses for the TLS pointer. Frequently
we were just getting away with this bug for a number of reasons:
o Real world application scenarios are very unlikely to use clone or fork
in blocks of DSP code.
o Linux by default runs the child process right after the fork, so the
child by luck will find all the right context in the DSP and userlocal
registers.
o So far the rdhwr instruction was emulated on all hardware so userlocal
wasn't getting referenced at all and the emulation wasn't suffering
from the issue since it gets it's value straight from the thread's
thread_info.
Fixed by moving the code to load the context from switch_to() to
finish_arch_switch which will be called by newborn and old threads.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The skb_morph function only freed the data part of the dst skb, but leaked
the auxiliary data such as the netfilter fields. This patch fixes this by
moving the relevant parts from __kfree_skb to skb_release_all and calling
it in skb_morph.
It also makes kfree_skbmem static since it's no longer called anywhere else
and it now no longer does skb_release_data.
Thanks to Yasuyuki KOZAKAI for finding this problem and posting a patch for
it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
1. update default MFPR value to drive strength fast 3mA and edge
detection logic disabled
2. update impacted MFP_CFG_xxx() macros
Signed-off-by: bridge wu <bridge.wu@marvell.com>
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: bridge wu <bridge.wu@marvell.com>
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The inet_ehash_locks_alloc() looks like this:
#ifdef CONFIG_NUMA
if (size > PAGE_SIZE)
x = vmalloc(...);
else
#endif
x = kmalloc(...);
Unlike it, the inet_ehash_locks_alloc() looks like this:
#ifdef CONFIG_NUMA
if (size > PAGE_SIZE)
vfree(x);
else
#else
kfree(x);
#endif
The error is obvious - if the NUMA is on and the size
is less than the PAGE_SIZE we leak the pointer (kfree is
inside the #else branch).
Compiler doesn't warn us because after the kfree(x) there's
a "x = NULL" assignment, so here's another (minor?) bug: we
don't set x to NULL under certain circumstances.
Boring explanation, I know... Patch explains it better.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds new device ids and features for mcp79 devices into the
forcedeth driver.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
xs_setup_{udp,tcp}() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Should not need separate cplb entry though as we cover L1 with a 4 meg page
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- remove duplicated defines for the BF561
- generalize L2 support (so that it works for BF54x) and mark it executable
- add support for reading/executing the Boot ROM sections
(since it has data/functions we may need at runtime)
- and fixup names for each map
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- no need to declare their sizes in the common header
- no need to tack on the section attribute as only the definition matters, not references
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Anomaly 05000312 - Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted:
DESCRIPTION:
When instruction cache is enabled, erroneous behavior may occur when any of the following instructions are interrupted:
. CSYNC
• SSYNC
• LCx =
• LTx = (only when LCx is non-zero)
• LBx = (only when LCx is non-zero)
When this problem occurs, a variety of incorrect things could happen, including an illegal instruction exception. Additional errors could
show up as an exception, a hardware error, or an instruction that is valid but different than the one that was expected.
WORKAROUND:
Place a cli before all SSYNC, CSYNC, "LCx =", "LTx =", and "LBx =" instructions to disable interrupts, and place an sti after each of these
instructions to re-enable interrupts. When these instructions are executed in code that is already non-interruptible, the problem will not
occur.
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
if (net_ratelimit())
IEEE80211_DEBUG_DROP(...)
can pollute the logs with messages like:
printk: 1 messages suppressed.
printk: 2 messages suppressed.
printk: 7 messages suppressed.
if debugging information is disabled. These messages are printed by
net_ratelimit(). Add a wrapper to net_ratelimit() that takes into account
the log level, so that net_ratelimit() is called only when we really want
to print something.
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove binary sysctls that never worked due to missing strategy functions.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove binary sysctls that never worked due to missing strategy functions.
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Current support for TRACE_IRQFLAGS and lockdep_sys_exit is broken.
IRQ flag tracing is broken for program checks. Even worse is that
the newly introduced calls to lockdep_sys_exit are in the critical
section code which is not supposed to call any C functions. In
addition the checks if locks are still held are also done when
returning to kernel code which is broken as well.
Fix all this by disabling interrupts and machine checks at the
exit paths and then do the appropriate checks and calls.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the abstraction functions got added, conversion here was
made incorrectly. As a result, the skb may end up pointing
to skb which got included to the probe skb and then was freed.
For it to trigger, however, skb_transmit must fail sending as
well.
Signed-off-by: Ilpo Jrvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the remaining IPVS sysctl entries over to to use CTL_UNNUMBERED,
I stronly doubt that anyone is using the sys_sysctl interface to
these variables.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl table check failed: /net/ipv4/vs/lblc_expiration .3.5.21.19 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/lblcr_expiration .3.5.21.20 Missing strategy
Switch these entried over to use CTL_UNNUMBERED as clearly
the sys_syscal portion wasn't working.
This is along the same lines as Christian Borntraeger's patch that fixes
up entries with no stratergy in net/ipv4/ipvs/ip_vs_ctl.c
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Running the latest git code I get the following messages during boot:
sysctl table check failed: /net/ipv4/vs/drop_entry .3.5.21.4 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/drop_packet .3.5.21.5 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/secure_tcp .3.5.21.6 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/sync_threshold .3.5.21.24 Missing strategy
I removed the binary sysctl handler for those messages and also removed
the definitions in ip_vs.h. The alternative would be to implement a
proper strategy handler, but syscall sysctl is deprecated.
There are other sysctl definitions that are commented out or work with
the default sysctl_data strategy. I did not touch these.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rtas_os_term() routine was being called at the wrong time.
The actual rtas call "os-term" will not ever return, and so
calling it from the panic notifier is too early. Instead,
call it from the machine_reset() call.
This splits the rtas_os_term() routine into two: one part to capture
the kernel panic message, invoked during the panic notifier, and
another part that is invoked during machine_reset().
Prior to this patch, the os-term call was never being made,
because panic_timeout was always non-zero. Calling os-term
helps keep the hypervisor happy! We have to keep the hypervisor
happy to avoid service, dump and error reporting problems.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current VDSO implementation is hardcoded to 128 byte cache blocks,
which are only used on IBM's 64-bit processors.
Convert it to get the cache block sizes out of vdso_data instead,
similar to how the ppc64 in-kernel cache flush does it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=9355
cpuidle always used to fallback to C2 if there is some bm activity while
entering C3. But, presence of C2 is not always guaranteed. Change cpuidle
algorithm to detect a safe_state to fallback in case of bm_activity and
use that state instead of C2.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On platforms doing non-coherent DMA (4xx, 8xx, ...), it's important
that the kmalloc minimum alignment is set to the cache line size, to
avoid sharing cache lines between different objects, so that DMA to
one of the objects doesn't corrupt the other.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
pcibios_free_controller() is now available for both 32 and 64 bits
but the header only declares it for 64 bits. This moves the
declaration down next to the pcibios_alloc_controller() one.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After an error condition, some ATAPI tape drives set DRQ=1 together
with ERR=1 when asking the host to transfer the CDB of the next packet
command (i.e. request sense). This patch, a revised version of
Alan/Mark's previous patch, adds ATA_HORKAGE_STUCK_ERR to workaround
the problem by ignoring the ERR bit and proceed sending the CDB.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Indeed my previous change to alloc_pskb has made it possible
for the TCP header to be misaligned iff the MTU is not a multiple
of 4 (and less than a page). So I suspect the optimised IPsec
MTU calculation is giving you just such an MTU :)
This patch fixes it by changing alloc_pskb to make sure that
the size is at least 32-bit aligned. This does not cause the
problem fixed by the previous patch because max_header is always
32-bit aligned which means that in the SG/NOTSO case this will
be a no-op.
I thought about putting this in the callers but all the current
callers are from TCP. If and when we get a non-TCP caller we
can always create a TCP wrapper for this function and move the
alignment over there.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
/*
* CPUs often take a performance hit when accessing unaligned memory
* locations. The actual performance hit varies, it can be small if the
* hardware handles it or large if we have to take an exception and fix
* it
* in software.
*
* Since an ethernet header is 14 bytes network drivers often end up
* with
* the IP header at an unaligned offset. The IP header can be aligned by
* shifting the start of the packet by 2 bytes. Drivers should do this
* with:
*
* skb_reserve(NET_IP_ALIGN);
*
* The downside to this alignment of the IP header is that the DMA is
* now
* unaligned. On some architectures the cost of an unaligned DMA is high
* and this cost outweighs the gains made by aligning the IP header.
*
* Since this trade off varies between architectures, we allow
* NET_IP_ALIGN
* to be overridden.
*/
This new function insl_16 allows to read form 32-bit IO and writes to
16-bit aligned memory. This is useful in above described scenario -
In particular with the AXIS AX88180 Gigabit Ethernet MAC.
Once the device is in 32-bit mode, reads from the RX FIFO always
decrements 4bytes.
While on the other side the destination address in SDRAM is always
16-bit aligned.
If we use skb_reserve(0) the receive buffer is 32-bit aligned but later
we hit a unaligned exception in the IP code.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Attempt to fix http://bugzilla.kernel.org/show_bug.cgi?id=8378
Hiroto Shibuya wrote to tell me that he has a VIA EPIA-EK10000 which
suffers from the reboot problem when no keyboard is attached. My first
patch works for him:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=59f4e7d572980a521b7bdba74ab71b21f5995538
But the latest patch does not work for him :
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=8b93789808756bcc1e5c90c99f1b1ef52f839a51
We found that it was necessary to also set the "disable keyboard" flag in
the command byte, as the first patch was doing. The second patch tries to
minimally modify the command byte, but it is not enough.
Please consider this simple one-line patch to help people with low end VIA
motherboards reboot when no keyboard is attached. Hiroto Shibuya has
verified that this works for him (as I no longer have an afflicted
machine).
Additional discussion:
Note that original patch from Truxton DOES
disable keyboard and this has been in main tree since 2.6.14, thus it must have
quite a bit of air time already.
http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.14.y.git;a=commit;h=59f4e7d572980a521b7bdba74ab71b21f5995538
Note that he only mention "System flag" in the description and comment, but
in the code, "disable keyboard" flag is set.
outb(0x14, 0x60); /* set "System flag" */
In 2.6.23, he made a change to read the current byte and then mask the flags,
but along this change, he only set the "System flag" and dropped the setting
of "disable keyboard" flag.
http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.23.y.git;a=commit;h=8b93789808756bcc1e5c90c99f1b1ef52f839a51
outb(cmd | 0x04, 0x60); /* set "System flag" */
So my request is to restore the setting of disable keyboard flag which has been
there since 2.6.14 but disappeared in 2.6.23.
Cc: Lee Garrett <lee-in-berlin@web.de>
Cc: "Hiroto Shibuya" <hiroto.shibuya@gmail.com>
Cc: Natalie Protasevich <protasnb@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Aristeu Rozanski <aris@ruivo.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix header file name for Voyager build.
In file included from arch/x86/kernel/setup_32.c:61:
include/asm-x86/mach-voyager/setup_arch.h:2:26: error: asm/setup_32.h: No such file or directory
make[1]: *** [arch/x86/kernel/setup_32.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
es7000_check_dst() contains a memcpy from 0, which probably should have been
a memset. Remove it and check the retunr value from acpi_get_table_header.
Noticed by: Joe Perches <joe@perches.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The only user is the a.out support.
It was therefore removed prior to the blackfin merge from all
architectures not supporting a.out.
Currently, Blackfin doesn't suppport a.out.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
ENOTSUPP is not a valid error code in the kernel (it is defined in some
NFS internal error codes and has been improperly used other places). In
the !CONFIG_SECURITY_SELINUX case though it is possible that we could
return this from selinux_audit_rule_init(). This patch just returns the
userspace valid EOPNOTSUPP.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: Fix NULL pointer dereference in nf_nat_move_storage()
[SUNHME]: VLAN support for sunhme
[CHELSIO]: Fix skb->dev setting.
[NETFILTER]: fix compat_nf_sockopt typo
[INET]: Fix potential kfree on vmalloc-ed area of request_sock_queue
[VIA_VELOCITY]: Don't oops on MTU change.
iwl4965: fix not correctly dealing with hotunplug
rt2x00: Fix chipset revision validation
iwl3945: place CCK rates in front of OFDM for supported rates
mac80211: Fix queuing of scan containing a SSID
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] N32 needs to use the compat version of sys_nfsservctl.
[MIPS] irq_cpu: use handle_percpu_irq handler to avoid dropping interrupts.
[MIPS] Sibyte: Fix name of clocksource.
[MIPS] SNI: s/achknowledge/acknowledge/
[MIPS] Makefile: Fix canonical system names
[MIPS] vpe: handle halting TCs in an errata safe way.
[MIPS] Sibyte: Stop timers before programming next even.
[MIPS] Sibyte: Increase minimum oneshot timer interval to two ticks.
[MIPS] Lasat: Fix overlap of interrupt number ranges.
[MIPS] SNI PCIT CPLUS: workaround for b0rked irq wiring of onboard PCI bus 1
[MIPS] Fix shadow register support.
[MIPS] Change get_cycles to always return 0.
[MIPS] Fix typo in R3000 TRACE_IRQFLAGS code
[MIPS] Sibyte: Replace use of removed IO_SPACE_BASE with IOADDR.
[MIPS] iounmap if in vr41xx_pciu_init() pci clock is over 33MHz
[MIPS] BCM1480: Remove duplicate acknowledge of timer interrupt.
[MIPS] Sibyte: pin timer interrupt to their cores.
[MIPS] Qemu: Add early printk, your friend in a cold night.
[MIPS] Convert reference to mem_map to pfn_to_page().
[MIPS] Sibyte: resurrect old cache hack.
The range of MIPS_CPU IRQ and the range of LASAT IRQ overlap.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Shadow register support would not possibly have worked on multicore
systems. The support code for it was also depending not on MIPS R2 but
VSMP or SMTC kernels even though it makes perfect sense with UP kernels.
SR sets are a scarce resource and the expected usage pattern is that
users actually hardcode the register set numbers in their code. So fix
the allocator by ditching it. Move the remaining CPU probe bits into
the generic CPU probe.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This avoids us executing an mfc0 c0_count instruction on processors which
don't have but also on certain R4000 and R4400 versions where reading from
the count register just in the very moment when its value equals
c0_compare will result in the timer interrupt getting lost.
There is still a number of users of get_cycles remaining outside the
arch code:
crypto/tcrypt.c: start = get_cycles();
crypto/tcrypt.c: end = get_cycles();
crypto/tcrypt.c: start = get_cycles();
crypto/tcrypt.c: end = get_cycles();
crypto/tcrypt.c: start = get_cycles();
crypto/tcrypt.c: end = get_cycles();
drivers/char/hangcheck-timer.c: return get_cycles();
drivers/char/hangcheck-timer.c: printk("Hangcheck: Using get_cycles().\n");
drivers/char/random.c: sample.cycles = get_cycles();
drivers/input/joystick/analog.c:#define GET_TIME(x) do { x = get_cycles(); }
include/linux/arcdevice.h: _x = get_cycles(); \
include/linux/arcdevice.h: _y = get_cycles(); \
mm/slub.c: if (!s->defrag_ratio || get_cycles() % 1024 > s->defrag_ratio)
mm/slub.c: p += 64 + (get_cycles() & 0xff) * sizeof(void *);
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c/eeprom: Recognize VGN as a valid Sony Vaio name prefix
i2c/eeprom: Hide Sony Vaio serial numbers
i2c-pasemi: Fix NACK detection
i2c-pasemi: Replace obsolete "driverfs" reference with "sysfs"
i2c: Make i2c_check_addr static
i2c-dev: Unbound new-style i2c clients aren't busy
i2c-dev: "how does it work" comments
i2c_check_addr is only used inside i2c-core now, so we can make it
static and stop exporting it. Thanks to David Brownell for noticing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
VDSP has double fault on core a/b inverted for BF561 -- bit 11 is core a while bit 12 is core b
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
since we have this always turned on now and dont want it off (and hasnt been an option in a while)
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
The request_sock_queue's listen_opt is either vmalloc-ed or
kmalloc-ed depending on the number of table entries. Thus it
is expected to be handled properly on free, which is done in
the reqsk_queue_destroy().
However the error path in inet_csk_listen_start() calls
the lite version of reqsk_queue_destroy, called
__reqsk_queue_destroy, which calls the kfree unconditionally.
Fix this and move the __reqsk_queue_destroy into a .c file as
it looks too big to be inline.
As David also noticed, this is an error recovery path only,
so no locking is required and the lopt is known to be not NULL.
reqsk_queue_yank_listen_sk is also now only used in
net/core/request_sock.c so we should move it there too.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: rt_check_expire() can take a long time, add a cond_resched()
[ISDN] sc: Really, really fix warning
[ISDN] sc: Fix sndpkt to have the correct number of arguments
[TCP] FRTO: Clear frto_highmark only after process_frto that uses it
[NET]: Remove notifier block from chain when register_netdevice_notifier fails
[FS_ENET]: Fix module build.
[TCP]: Make sure write_queue_from does not begin with NULL ptr
[TCP]: Fix size calculation in sk_stream_alloc_pskb
[S2IO]: Fixed memory leak when MSI-X vector allocation fails
[BONDING]: Fix resource use after free
[SYSCTL]: Fix warning for token-ring from sysctl checker
[NET] random : secure_tcp_sequence_number should not assume CONFIG_KTIME_SCALAR
[IWLWIFI]: Not correctly dealing with hotunplug.
[TCP] FRTO: Plug potential LOST-bit leak
[TCP] FRTO: Limit snd_cwnd if TCP was application limited
[E1000]: Fix schedule while atomic when called from mii-tool.
[NETX]: Fix build failure added by 2.6.24 statistics cleanup.
[EP93xx_ETH]: Build fix after 2.6.24 NAPI changes.
[PKT_SCHED]: Check subqueue status before calling hard_start_xmit
Include linux/pagemap.h for release_pages and page_cache_release.
Fixes compilation error in arch/cris/mm/init.c when CONFIG_SWAP is unset.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve and bugfix CRIS v10 fast timers.
- irq_handler_t now only takes two arguments.
- Keep interrupts disabled as long as we have a reference to the
fasttimer list and only enable them while doing the callback.
del_fast_timer may be called from other interrupt context.
- Fix bug where debug code could return without calling local_irq_restore.
- Use jiffies instead of usec (change from struct timeval to fasttime_t).
- Don't initialize static variables to zero.
- Remove obsolete #ifndef DECLARE_WAITQUEUE code.
- fast_timer_init should be __initcall.
- Change status/debug variables to unsigned.
- Remove CVS log and CVS id.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In file included from include/asm/byteorder.h:23,
from include/asm-generic/bitops/le.h:5,
from include/asm-generic/bitops/ext2-non-atomic.h:4,
from include/asm/bitops.h:163,
from include/linux/bitops.h:17,
from include/asm/posix_types.h:55,
from include/linux/posix_types.h:47,
from include/linux/types.h:11,
from include/linux/capability.h:16,
from include/linux/sched.h:49,
from arch/cris/kernel/asm-offsets.c:1:
include/linux/byteorder/little_endian.h:43: parse error before "__cpu_to_le64p"
include/linux/byteorder/little_endian.h:44: warning: return type defaults to `int'
include/linux/byteorder/little_endian.h: In function `__cpu_to_le64p':
include/linux/byteorder/little_endian.h:45: `__le64' undeclared (first use in this function)
Remove include of asm/bitops.h, not needed here, corrects compilation error
(__le64 undeclared).
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Corrects compile errors and the following:
- Remove oldset parameter from do_signal and do_notify_resume.
- Modified to fit new consolidated IRQ handling code.
- Reverse check order between external nmi and watchdog nmi to avoid false
watchdog oops in case of a glitch on the nmi pin.
- Return from an pin-generated NMI the same way as for other interrupts.
- Moved blocking of ethernet rx/tx irq from ethernet interrupt handler to
low-level asm interrupt handlers. Fixed in the multiple interrupt
handler also.
- Add space for thread local storage in thread_info struct.
- Add NO_DMA to Kconfig, and include arch specific Kconfig using arch
independent path. Include subsystem Kconfigs for pcmcia, usb, i2c,
rtc and pci.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New (updated) version of ethernet driver for cris v10.
- First steps to simplify and make the MII code more similar
between the etrax100 and etraxfs ports.
- Start the transmit queue before enabling tx interrupts
to avoid race with the first frame.
- Flip the comparition statement to stick to physical addresses
to avoid phys_to_virt mapping a potential null pointer.
This was not an error but the change simplifies debugging
of address-space mappings.
- Made myPrevRxDesc local to e100_rx since it was only used there.
Fixed out of memory handling in e100_rx. If dev_alloc_skb() fails
persistently the system is hosed anyway but at least it won't
loop in an interrupt handler.
- Correct some code formatting issues.
- Add defines SET_ETH_ENABLE_LEDS, SET_ETH_DISABLE_LEDS
and SET_ETH_AUTONEG used in new cris v10 ethernet driver.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include file linux/compiler.h is needed for 'likely'.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include asm/irq.h to avoid undefined value warning.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove int from prototype, no longer needed and causes compile error.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86 32-bit isn't saving the stack pointer to pt_regs->esp when an
interrupt occurs.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Tested-by: Robert Fitzsimons <robfitz@273k.net>
Cc: Andi Kleen <ak@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With 64KB blocksize, a directory entry can have size 64KB which does not
fit into 16 bits we have for entry lenght. So we store 0xffff instead and
convert value when read from / written to disk. The patch also converts
some places to use ext3_next_entry() when we are changing them anyway.
[akpm@linux-foundation.org: coding-style cleanups]
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is my trivial patch to swat innumerable little bugs with a single
blow.
After some intensive review (my apologies for not having gotten to this
sooner) what we have looks like a good base to build on with the current
pid namespace code but it is not complete, and it is still much to simple
to find issues where the kernel does the wrong thing outside of the initial
pid namespace.
Until the dust settles and we are certain we have the ABI and the
implementation is as correct as humanly possible let's keep process ID
namespaces behind CONFIG_EXPERIMENTAL.
Allowing us the option of fixing any ABI or other bugs we find as long as
they are minor.
Allowing users of the kernel to avoid those bugs simply by ensuring their
kernel does not have support for multiple pid namespaces.
[akpm@linux-foundation.org: coding-style cleanups]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Kir Kolyshkin <kir@swsoft.com>
Cc: Kirill Korotaev <dev@sw.ru>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Firmware like PNPBIOS or ACPI can report the address space consumed by the
RTC. The actual space consumed may be less than the size (RTC_IO_EXTENT)
assumed by the RTC driver.
The PNP core doesn't request resources yet, but I'd like to make it do so.
If/when it does, the RTC_IO_EXTENT request may fail, which prevents the RTC
driver from loading.
Since we only use the RTC index and data registers at RTC_PORT(0) and
RTC_PORT(1), we can fall back to requesting just enough space for those.
If the PNP core requests resources, this results in typical I/O port usage
like this:
0070-0073 : 00:06 <-- PNP device 00:06 responds to 70-73
0070-0071 : rtc <-- RTC driver uses only 70-71
instead of the current:
0070-0077 : rtc <-- RTC_IO_EXTENT == 8
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for version 2 of the ioatdma device. This device handles
the descriptor chain and DCA services slightly differently:
- Instead of moving the dma descriptors between a busy and an idle chain,
this new version uses a single circular chain so that we don't have
rewrite the next_descriptor pointers as we add new requests, and the
device doesn't need to re-read the last descriptor.
- The new device has the DCA tags defined internally instead of needing
them defined statically.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: "Williams, Dan J" <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert 62d0df6406.
This was originally intended as a simple initial example of how to create a
control groups subsystem; it wasn't intended for mainline, but I didn't make
this clear enough to Andrew.
The CFS cgroup subsystem now has better functionality for the per-cgroup usage
accounting (based directly on CFS stats) than the "usage" status file in this
patch, and the "load" status file is rather simplistic - although having a
per-cgroup load average report would be a useful feature, I don't believe this
patch actually provides it. If it gets into the final 2.6.24 we'd probably
have to support this interface for ever.
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For administrative purpose, we want to query actual block usage for
hugetlbfs file via fstat. Currently, hugetlbfs always return 0. Fix that
up since kernel already has all the information to track it properly.
Signed-off-by: Ken Chen <kenchen@google.com>
Acked-by: Adam Litke <agl@us.ibm.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a second parameter 'delta' to hugetlb_get_quota and hugetlb_put_quota to
allow bulk updating of the sbinfo->free_blocks counter. This will be used by
the next patch in the series.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Cc: Ken Chen <kenchen@google.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: David Gibson <hermes@gibson.dropbear.id.au>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When calling get_user_pages(), a write flag is passed in by the caller to
indicate if write access is required on the faulted-in pages. Currently,
follow_hugetlb_page() ignores this flag and always faults pages for
read-only access. This can cause data corruption because a device driver
that calls get_user_pages() with write set will not expect COW faults to
occur on the returned pages.
This patch passes the write flag down to follow_hugetlb_page() and makes
sure hugetlb_fault() is called with the right write_access parameter.
[ezk@cs.sunysb.edu: build fix]
Signed-off-by: Adam Litke <agl@us.ibm.com>
Reviewed-by: Ken Chen <kenchen@google.com>
Cc: David Gibson <hermes@gibson.dropbear.id.au>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Erez Zadok <ezk@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pud_clear wasn't setting the _PAGE_NEWPAGE bit, fooling tlb_flush into
thinking that this area of the address space was up-to-date and not unmapping
whatever was covered by the pud.
This manifested itself as ldconfig on x86_64 complaining about the first
library it looked at not being a valid ELF file. A config file is mapped at
0x4000000, as the only thing mapped under its pud, and unmapped. The
unmapping caused a pud_clear, which, due to this bug, didn't actually unmap
the config file data on the host. The first library is then mapped at the
same location, but is not actually mapped on the host because accesses to it
cause no page faults. As a result, ldconfig sees the old config file data.
[akpm@linux-foundation.org: coding-style cleanups]
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We round up the header size in sk_stream_alloc_pskb so that
TSO packets get zero tail room. Unfortunately this rounding
up is not coordinated with the select_size() function used by
TCP to calculate the second parameter of sk_stream_alloc_pskb.
As a result, we may allocate more than a page of data in the
non-TSO case when exactly one page is desired.
In fact, rounding up the head room is detrimental in the non-TSO
case because it makes memory that would otherwise be available to
the payload head room. TSO doesn't need this either, all it wants
is the guarantee that there is no tail room.
So this patch fixes this by adjusting the skb_reserve call so that
exactly the requested amount (which all callers have calculated in
a precise way) is made available as tail room.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
hwmon: (i5k_amb) Convert macros to C functions
hwmon: (w83781d) Add missing curly braces
hwmon: (abituguru3) Identify ABit IP35 Pro as such
hwmon: (f75375s) pwmX_mode sysfs files writable for f75375 variant
hwmon: (f75375s) On n2100 systems, set fans to full speed on boot
hwmon: (f75375s) Allow setting up fans with platform_data
hwmon: (f75375s) Add new style bindings
hwmon: (lm70) Convert semaphore to mutex
hwmon: (applesmc) Add support for Mac Pro 2 x Quad-Core
hwmon: (abituguru3) Add support for 2 new motherboards
hwmon: (ibmpex) Change printk to dev_{info,err} macros
hwmon: (i5k_amb) New memory temperature sensor driver
hwmon: (f75375s) fix pwm mode setting
hwmon: (ibmpex.c) fix NULL dereference
hwmon: (sis5595) Split sis5595_attributes_opt
hwmon: (sis5595) Add individual alarm files
hwmon: (w83627hf) push nr+1 offset into *_REG_FAN macros and simplify
hwmon: (w83627hf) hoist nr-1 offset out of show-store-temp-X
hwmon: Add power meter spec to Documentation/hwmon/sysfs-interface
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Silence an annoying boot message
[POWERPC] Fix early btext debug on PowerMac
[POWERPC] Demote clockevent printk to KERN_DEBUG
[POWERPC] Fix CONFIG_SMP=n build error on ppc64
[POWERPC] Avoid unpaired stwcx. on some processors
[POWERPC] Fix oops related to 4xx flush_tlb_page modification
[POWERPC] cpm: Fix a couple minor issues in cpm_common.c.
[POWERPC] Add -mno-spe for ARCH=powerpc builds
This patch reverts Eric's commit 2b008b0a8e
It diets .text & .data section of the kernel if CONFIG_NET_NS is not set.
This is safe after list operations cleanup.
Signed-of-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inetpeer.c tracks the LRU list of inet_perr-s, but makes
it by hands. Use the list_head-s for this.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The context switch code in the kernel issues a dummy stwcx. to clear the
reservation, as recommended by the architecture. However, some processors
can have issues if this stwcx to address A occurs while the reservation
is already held to a different address B. To avoid this problem, the dummy
stwcx. needs to be paired with a dummy lwarx to the same address.
This adds the dummy lwarx, and creates a cpu feature bit to indicate
which cpus are affected. Tested on mpc8641_hpcn_defconfig in
arch/powerpc; build tested in arch/ppc.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
...and fix a couple of bugs in the NBD, CIFS and OCFS2 socket handlers.
Looking at the sock->op->shutdown() handlers, it looks as if all of them
take a SHUT_RD/SHUT_WR/SHUT_RDWR argument instead of the
RCV_SHUTDOWN/SEND_SHUTDOWN arguments.
Add a helper, and then define the SHUT_* enum to ensure that kernel users
of shutdown() don't get confused.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: Mark Fasheh <mark.fasheh@oracle.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Userland neighbor discovery options are typically heavily involved with
the interface on which thay are received: add a missing ifindex field to
the original struct. Thanks to Rmi Denis-Courmont.
Signed-off-by: Pierre Ynard <linkfanel@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-virtio:
virtio: Force use of power-of-two for descriptor ring sizes
lguest: Fix lguest virtio-blk backend size computation
virtio: Fix used_idx wrap-around
virtio: more fallout from scatterlist changes.
virtio: fix vring_init for 64 bits
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (39 commits)
[INET]: Small possible memory leak in FIB rules
[NETNS]: init dev_base_lock only once
[UNIX]: The unix_nr_socks limit can be exceeded
[AF_UNIX]: Convert socks to unix_socks in scan_inflight, not in callbacks
[AF_UNIX]: Make unix_tot_inflight counter non-atomic
[AF_PACKET]: Allow multicast traffic to be caught by ORIGDEV when bonded
ssb: Fix PCMCIA-host lowlevel bus access
mac80211: fix MAC80211_RCSIMPLE Kconfig
mac80211: make "decrypt failed" messages conditional upon MAC80211_DEBUG
mac80211: use IW_AUTH_PRIVACY_INVOKED rather than IW_AUTH_KEY_MGMT
mac80211: remove unused driver ops
mac80211: remove ieee80211_common.h
softmac: MAINTAINERS update
rfkill: Fix sparse warning
rfkill: Use mutex_lock() at register and add sanity check
iwlwifi: select proper rate control algorithm
mac80211: allow driver to ask for a rate control algorithm
mac80211: don't allow registering the same rate control twice
rfkill: Use subsys_initcall
mac80211: make simple rate control algorithm built-in
...
restore sigcontext is taking a DNA exception while restoring FP context
from the user stack, during the sigreturn. Appended patch fixes it by
doing clts() if the app doesn't touch FP during the signal handler
execution. This will stop generating a DNA, during the fxrstor in the
sigreturn.
This improves 64-bit lat_sig numbers by ~30% on my core2 platform.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The virtio descriptor rings of size N-1 were nicely set up to be
aligned to an N-byte boundary. But as Anthony Liguori points out, the
free-running indices used by virtio require that the sizes be a power
of 2, otherwise we get problems on wrap (demonstrated with lguest).
So we replace the clever "2^n-1" scheme with a simple "align to page
boundary" scheme: this means that all virtio rings take at least two
pages, but it's safer than guessing cache alignment.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch fixes a typo in vring_init(). This happens to work today in lguest
because the sizeof(struct vring_desc) is 16 and struct vring contains 3
pointers and an unsigned int so on 32-bit
sizeof(struct vring_desc) == sizeof(struct vring). However, this is no longer
true on 64-bit where the bug is exposed.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch fixes a small memory leak. Default fib rules can be deleted by
the user if the rule does not carry FIB_RULE_PERMANENT flag, f.e. by
ip rule flush
Such a rule will not be freed as the ref-counter has 2 on start and becomes
clearly unreachable after removal.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This counter is _always_ modified under the unix_gc_lock spinlock,
so its atomicity can be provided w/o additional efforts.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver operations set_ieee8021x(), set_port_auth() and
set_privacy_invoked() are not used by any drivers, except
set_privacy_invoked() they aren't even used by mac80211.
Remove them at least until we need to support drivers with
mac80211 that require getting this information.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows a driver to ask for a specific rate control algorithm.
The rate control algorithm asked for must be registered and be
available as a module or built-in.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The intent of the assertion in skb_truesize_check() is to check
for skb->truesize being decremented too much by other code,
resulting in a wraparound below zero.
The type of the right side of the comparison causes the compiler to
promote the left side to an unsigned type, despite the presence of an
explicit type cast. This defeats the check for negativity.
Ensure both sides of the comparison are a signed type to prevent the
implicit type conversion.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many places that get the dst entry, increase the
__use counter and set the "lastuse" time stamp.
Make a helper for this.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use struct boot_params instead of PARAM + 0xoffsets.
Fixes one of many Voyager build problems.
arch/x86/kernel/setup_32.c:543: error: 'PARAM' undeclared (first use in this function)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] IOSAPIC bogus error cleanup
[IA64] Update printing of feature set bits
[IA64] Fix IOSAPIC delivery mode setting
[IA64] XPC heartbeat timer function must run on CPU 0
[IA64] Clean up /proc/interrupts output
[IA64] Disable/re-enable CPE interrupts on Altix
[IA64] Clean-up McKinley Errata message
[IA64] Add gate.lds to list of files ignored by Git
[IA64] Fix section mismatch in contig.c version of per_cpu_init()
[IA64] Wrong args to memset in efi_gettimeofday()
[IA64] Remove duplicate includes from ia32priv.h
[IA64] fix number of bytes zeroed by sys_fw_init() in arch/ia64/hp/sim/boot/fw-emu.c
[IA64] Fix perfmon sysctl directory modes
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits)
sh: remove dead config symbols from SH code
sh: Kill off broken snapgear ds1302 code.
sh: Add a dummy vga.h.
rtc: rtc-sh: Zero out tm value for invalid rtc states.
rtc: sh-rtc: Handle rtc_device_register() failure properly.
sh: Fix heartbeart on Solution Engine series
sh: Remove SCI_NPORTS from sh-sci.h
sh: Fix up PAGE_KERNEL_PCC() for nommu.
sh: hs7751rvoip: Kill off dead IPR IRQ mappings.
sh: hs7751rvoip: irq.c needs linux/interrupt.h.
sh: Kill off __{copy,clear}_user_page().
sh: Optimized copy_{to,from}_user_page() for SH-4.
sh: Wire up clear_user_highpage().
sh: Kill off the remaining ST40 cruft.
superhyway: Handle device_register() retval properly.
sh: kgdb sysrq depends on magic sysrq.
sh: Add -Werror for clean directories.
sh: Fix up kgdb build with modular sh-sci.
sh: Export __{s,u}divsi3_i4i on all CPUs.
sh: Fix up kgdb-on-NMI branch target.
...
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (37 commits)
[POWERPC] EEH: Make sure warning message is printed
[POWERPC] Make altivec code in swsusp_32.S depend on CONFIG_ALTIVEC
[POWERPC] windfarm: Fix windfarm thread freezer interaction
[POWERPC] Fix si_addr value on low level hash failures
[POWERPC] Refresh ppc64_defconfig and enable pasemi-related options
[POWERPC] pasemi: Update defconfig
[POWERPC] iSeries: Fix ref counting in vio setup
[POWERPC] ] Fix memset size error
[POWERPC] Fix link errors for allyesconfig
[POWERPC] iSeries_init_IRQ non-PCI tidy
[POWERPC] Change fallocate to match unistd.h on powerpc
[POWERPC] EEH: Avoid crash on null device
[POWERPC] EEH: Drivers that need reset trump others
[POWERPC] EEH: Clean up comments
[POWERPC] Fix off-by-one error in setting decrementer on Book E/4xx (v2)
[POWERPC] Fix switch_slb handling of 1T ESID values
[POWERPC] Fix build failure when CONFIG_VIRT_CPU_ACCOUNTING is not defined
[POWERPC] Include udbg.h when using udbg_printf
[POWERPC] Fix cache line vs. block size confusion
[POWERPC] Fix sysctl table check failure on PowerMac
...
The old NO_IRQ define some platforms had was long ago declared obsolete
and wrong. FRV should therefore not be re-introducing this, especially as
IRQs are usually unsigned in the kernel. The "no IRQ" case is defined to be
zero and Linus made this rather clear at the time.
arch/frv shows no dependancy on this but it might show up driver fixes
needing doing I guess
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Use "is_power_of_2" macro for simplicity.
[SPARC]: Remove duplicate includes.
This patch adds a proper prototype for migration_init() in
include/linux/sched.h
Since there's no point in always returning 0 to a caller that doesn't check
the return value it also changes the function to return void.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
SMP balancing is done with IRQs disabled and can iterate the full rq.
When rqs are large this can cause large irq-latencies. Limit the nr of
iterations on each run.
This fixes a scheduling latency regression reported by the -rt folks.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Gregory Haskins <ghaskins@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
remove PREEMPT_RESTRICT. (this is a separate commit so that any
regression related to the removal itself is bisectable)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix a !SMP build error:
drivers/kvm/kvm_main.c: In function 'kvm_flush_remote_tlbs':
drivers/kvm/kvm_main.c:220: error: implicit declaration of function 'smp_call_function_mask'
(and also avoid unused function warning related to up_smp_call_function()
not making use of the 'func' parameter.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since powerpc started using CONFIG_GENERIC_CLOCKEVENTS, the
deterministic CPU accounting (CONFIG_VIRT_CPU_ACCOUNTING) has been
broken on powerpc, because we end up counting user time twice: once in
timer_interrupt() and once in update_process_times().
This fixes the problem by pulling the code in update_process_times
that updates utime and stime into a separate function called
account_process_tick. If CONFIG_VIRT_CPU_ACCOUNTING is not defined,
there is a version of account_process_tick in kernel/timer.c that
simply accounts a whole tick to either utime or stime as before. If
CONFIG_VIRT_CPU_ACCOUNTING is defined, then arch code gets to
implement account_process_tick.
This also lets us simplify the s390 code a bit; it means that the s390
timer interrupt can now call update_process_times even when
CONFIG_VIRT_CPU_ACCOUNTING is turned on, and can just implement a
suitable account_process_tick().
account_process_tick() now takes the task_struct * as an argument.
Tested both with and without CONFIG_VIRT_CPU_ACCOUNTING.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
we lost the sched_min_granularity tunable to a clever optimization
that uses the sched_latency/min_granularity ratio - but the ratio
is quite unintuitive to users and can also crash the kernel if the
ratio is set to 0. So reintroduce the min_granularity tunable,
while keeping the ratio maintained internally.
no functionality changed.
[ mingo@elte.hu: some fixlets. ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Newer Itanium versions have added additional processor feature set
bits. This patch prints all the implemented feature set bits. Some
bit descriptions have not been made public. For those bits, a generic
"Feature set X bit Y" message is printed. Bits that are not implemented
will no longer be printed.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
SCTP-AUTH and future ADD-IP updates have a requirement to
do additional verification of parameters and an ability to
ABORT the association if verification fails. So, introduce
additional return code so that we can clear signal a required
action.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Added blk_unplug interface, allowing all invocations of unplugs to result
in a generated blktrace UNPLUG.
Signed-off-by: Alan D. Brunelle <Alan.Brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
kmap_atomic calls flush_tlb_page with a NULL VMA and thus we end
up dereferencing a NULL pointer to try and get the context.id.
If the VMA is null use the global pid value of 0.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Allow initializing fans on systems where BIOS does not do that by
default.
- define f75375s_platform_data in new file f75375s.h
- if platform_data was provided, set fans accordingly in f75375_init()
- split set_pwm_enable() to a sysfs callback and directly usable
set_pwm_enable_direct()
Signed-off-by: Riku Voipio <riku.voipio@movial.fi>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
New driver to read FB-DIMM temperature sensors on systems with the
Intel 5000 series chipsets.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
For kernel addresses between TASK_SIZE and PAGE_OFFSET,
flush_tlb_kern_range() does not work as would be expected.
The TLB invalidate works with a matching ASID, or on entries marked as
global. The set_pte_at() macro marks addresses >= PAGE_OFFSET as
global, but not addresses from TASK_SIZE to PAGE_OFFSET, which are
also kernel addresses.
The result is that the entries in this range are not actually
invalidated by flush_tlb_kern_range().
This patch instead marks addresses >= TASK_SIZE as global.
Signed-off-by: Satoru Fujii <s-fujii@ct.jp.nec.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the fallocate system call on powerpc to match its unistd.h.
This implies none of these system calls are currently working with the
unistd.h sys call values:
fallocate
signalfd
timerfd
eventfd
sync_file_range2
Signed-off-by: Patrick Mansfield <patmans@us.ibm.com>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The decrementer in Book E and 4xx processors interrupts on the
transition from 1 to 0, rather than on the 0 to -1 transition as on
64-bit server and 32-bit "classic" (6xx/7xx/7xxx) processors. At the
moment we subtract 1 from the count of how many decrementer ticks are
required before the next interrupt before putting it into the
decrementer, which is correct for server/classic processors, but could
possibly cause the interrupt to happen too early on Book E and 4xx if
the timebase/decrementer frequency is low.
This fixes the problem by making set_dec subtract 1 from the count for
server and classic processors, instead of having the callers subtract
1. Since set_dec already had a bunch of ifdefs to handle different
processor types, there is no net increase in ugliness. :)
Note that calling set_dec(0) may not generate an interrupt on some
processors. To make sure that decrementer_set_next_event always calls
set_dec with an interval of at least 1 tick, we set min_delta_ns of
the decrementer_clockevent to correspond to 2 ticks (2 rather than 1
to compensate for truncations in the conversions between ticks and
ns).
This also removes a redundant call to set the decrementer to
0x7fffffff - it was already set to that earlier in timer_interrupt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a tunable that will allow ADD_IP to work without
AUTH for backward compatibility. The default value is off since
the default value for ADD_IP is off as well. People who need
to use ADD-IP with older implementations take risks of connection
hijacking and should consider upgrading or turning this tunable on.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
After learning more about rcu, it looks like the ADD-IP hadling
doesn't need to call call_rcu_bh. All the rcu critical sections
use rcu_read_lock, so using call_rcu_bh is wrong here.
Now, restore the local_bh_disable() code blocks and use normal
call_rcu() calls. Also restore the missing return statement.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Commit d0ce92910b broke several retransmit
cases including fast retransmit. The reason is that we should
only delay by rto while doing retranmists as a result of a timeout.
Retransmit as a result of path mtu discover, fast retransmit, or
other evernts that should trigger immidiate retransmissions got broken.
Also, since rto is doubled prior to marking of packets elegable for
retransmission, we never marked correct chunks anyway.
The fix is provide a reason for a given retransmission so that we
can mark chunks appropriately and to save the old rto value to do
comparisons against.
All regressions tests passed with this code.
Spotted by Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Commit ed6dcf4a in the history.git tree broke netlink_unicast timeouts
by moving the schedule_timeout() call to a new function that doesn't
propagate the remaining timeout back to the caller. This means on each
retry we start with the full timeout again.
ipc/mqueue.c seems to actually want to wait indefinitely so this
behaviour is retained.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As done two years ago on IP route cache table (commit
22c047ccbc) , we can avoid using one
lock per hash bucket for the huge TCP/DCCP hash tables.
On a typical x86_64 platform, this saves about 2MB or 4MB of ram, for
litle performance differences. (we hit a different cache line for the
rwlock, but then the bucket cache line have a better sharing factor
among cpus, since we dirty it less often). For netstat or ss commands
that want a full scan of hash table, we perform fewer memory accesses.
Using a 'small' table of hashed rwlocks should be more than enough to
provide correct SMP concurrency between different buckets, without
using too much memory. Sizing of this table depends on
num_possible_cpus() and various CONFIG settings.
This patch provides some locking abstraction that may ease a future
work using a different model for TCP/DCCP table.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the master daemon to sync the connection when it is about
to close. This makes the connections on the backup to close or timeout
according their state. Before the sync was performed only if the
connection is in ESTABLISHED state which always made the connections to
timeout in the hard coded 3 minutes. However the Andy Gospodarek's patch
([IPVS]: use proper timeout instead of fixed value) effectively did nothing
more than increasing this to 15 minutes (Established state timeout). So
this patch makes use of proper timeout since it syncs the connections on
status changes to FIN_WAIT (2min timeout) and CLOSE (10sec timeout).
However if the backup misses CLOSE hopefully it did not miss FIN_WAIT.
Otherwise we will just have to wait for the ESTABLISHED state timeout. As
it is without this patch. This way the number of the hanging connections
on the backup is kept to minimum. And very few of them will be left to
timeout with a long timeout.
This is important if we want to make use of the fix for the real server
overcommit on master/backup fail-over.
Signed-off-by: Rumen G. Bogdanovski <rumen@voicecho.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the problem with node overload on director fail-over.
Given the scenario: 2 nodes each accepting 3 connections at a time and 2
directors, director failover occurs when the nodes are fully loaded (6
connections to the cluster) in this case the new director will assign
another 6 connections to the cluster, If the same real servers exist
there.
The problem turned to be in not binding the inherited connections to
the real servers (destinations) on the backup director. Therefore:
"ipvsadm -l" reports 0 connections:
root@test2:~# ipvsadm -l
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP test2.local:5999 wlc
-> node473.local:5999 Route 1000 0 0
-> node484.local:5999 Route 1000 0 0
while "ipvs -lnc" is right
root@test2:~# ipvsadm -lnc
IPVS connection entries
pro expire state source virtual destination
TCP 14:56 ESTABLISHED 192.168.0.10:39164 192.168.0.222:5999
192.168.0.51:5999
TCP 14:59 ESTABLISHED 192.168.0.10:39165 192.168.0.222:5999
192.168.0.52:5999
So the patch I am sending fixes the problem by binding the received
connections to the appropriate service on the backup director, if it
exists, else the connection will be handled the old way. So if the
master and the backup directors are synchronized in terms of real
services there will be no problem with server over-committing since
new connections will not be created on the nonexistent real services
on the backup. However if the service is created later on the backup,
the binding will be performed when the next connection update is
received. With this patch the inherited connections will show as
inactive on the backup:
root@test2:~# ipvsadm -l
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP test2.local:5999 wlc
-> node473.local:5999 Route 1000 0 1
-> node484.local:5999 Route 1000 0 1
rumen@test2:~$ cat /proc/net/ip_vs
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP C0A800DE:176F wlc
-> C0A80033:176F Route 1000 0 1
-> C0A80032:176F Route 1000 0 1
Regards,
Rumen Bogdanovski
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Rumen G. Bogdanovski <rumen@voicecho.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Dave Miller noted various cases where line disciplines for things like
ppp go poking around in termios themselves in ways that broke with the
new termios code. Rather than have them all learning about termios
internals provide proper methods for this
- tty_mode_ioctl()
This handles all the terminal mode handling for speed/carrier
etc and none of the methods are ldisc dependant so they can be called
by any user
- tty_perform_flush()
This extracts the flush functionality and enables pppd the ppp
layer to share it cleanly.
The existing n_tty_ioctl code is refactored in this patch to provide
the new functions and to call them itself appropriately. This patch
has no (intended) behaviour changes and simply prepares for the other
fixes.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ralf Baechle