Yang Li has reported that drain_all_pages triggers a WARN_ON which means
that this function is called earlier than the mm_percpu_wq is
initialized on arm64 with CMA configured:
WARNING: CPU: 2 PID: 1 at mm/page_alloc.c:2423 drain_all_pages+0x244/0x25c
Modules linked in:
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.11.0-rc1-next-20170310-00027-g64dfbc5 #127
Hardware name: Freescale Layerscape 2088A RDB Board (DT)
task: ffffffc07c4a6d00 task.stack: ffffffc07c4a8000
PC is at drain_all_pages+0x244/0x25c
LR is at start_isolate_page_range+0x14c/0x1f0
[...]
drain_all_pages+0x244/0x25c
start_isolate_page_range+0x14c/0x1f0
alloc_contig_range+0xec/0x354
cma_alloc+0x100/0x1fc
dma_alloc_from_contiguous+0x3c/0x44
atomic_pool_init+0x7c/0x208
arm64_dma_init+0x44/0x4c
do_one_initcall+0x38/0x128
kernel_init_freeable+0x1a0/0x240
kernel_init+0x10/0xfc
ret_from_fork+0x10/0x20
Fix this by moving the whole setup_vmstat which is an initcall right now
to init_mm_internals which will be called right after the WQ subsystem
is initialized.
Link: http://lkml.kernel.org/r/20170315164021.28532-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Yang Li <pku.leo@gmail.com>
Tested-by: Yang Li <pku.leo@gmail.com>
Tested-by: Xiaolong Ye <xiaolong.ye@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
getrandom(2). It's faster and arguably more secure than cut-down MD5
that we had been using.
Also do some code cleanup.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAljCENEACgkQ8vlZVpUN
gaP8lwf7BFtF52mKQcsVYxxZtRPH5dQwJCh3rohQ0WEJi5hHyZPZNz24dPHgc8Xl
GDq7v7o10dL3aeK6P51lYNcDb9xwYakCXm5sw46c5juca/VAVaxHb/kSDPSPUCNj
7n7mNSM61UhYAN10AXi9FGJo/Rdr0U5F1VfoWVYqaHYsItYLCjlSk6ob7vKxCPUd
458qaGBvK8luwQgFPQftJ20j81zXNuRe5JHjCQ2LtaRWM8kNI/wmyNSokD73BkZl
k8B7VqG4YpKp+4xgThp12GpXHrKB9kzQfmM4dZQQiGai9Ni59+iNqEcumv0Jb5MG
gY/m5Wc1Q45/5FosPXQYHzMPHrSJ3A==
=g1OD
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random updates from Ted Ts'o:
"Change get_random_{int,log} to use the CRNG used by /dev/urandom and
getrandom(2). It's faster and arguably more secure than cut-down MD5
that we had been using.
Also do some code cleanup"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: move random_min_urandom_seed into CONFIG_SYSCTL ifdef block
random: convert get_random_int/long into get_random_u32/u64
random: use chacha20 for get_random_int/long
random: fix comment for unused random_min_urandom_seed
random: remove variable limit
random: remove stale urandom_init_wait
random: remove stale maybe_reseed_primary_crng
But first introduce a trivial header and update usage sites.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
But first update the usage sites with the new header dependency.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/task_stack.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task_stack.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/task.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to move softlockup APIs out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
<linux/nmi.h> already includes <linux/sched.h>.
Include the <linux/nmi.h> header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull IDR rewrite from Matthew Wilcox:
"The most significant part of the following is the patch to rewrite the
IDR & IDA to be clients of the radix tree. But there's much more,
including an enhancement of the IDA to be significantly more space
efficient, an IDR & IDA test suite, some improvements to the IDR API
(and driver changes to take advantage of those improvements), several
improvements to the radix tree test suite and RCU annotations.
The IDR & IDA rewrite had a good spin in linux-next and Andrew's tree
for most of the last cycle. Coupled with the IDR test suite, I feel
pretty confident that any remaining bugs are quite hard to hit. 0-day
did a great job of watching my git tree and pointing out problems; as
it hit them, I added new test-cases to be sure not to be caught the
same way twice"
Willy goes on to expand a bit on the IDR rewrite rationale:
"The radix tree and the IDR use very similar data structures.
Merging the two codebases lets us share the memory allocation pools,
and results in a net deletion of 500 lines of code. It also opens up
the possibility of exposing more of the features of the radix tree to
users of the IDR (and I have some interesting patches along those
lines waiting for 4.12)
It also shrinks the size of the 'struct idr' from 40 bytes to 24 which
will shrink a fair few data structures that embed an IDR"
* 'idr-4.11' of git://git.infradead.org/users/willy/linux-dax: (32 commits)
radix tree test suite: Add config option for map shift
idr: Add missing __rcu annotations
radix-tree: Fix __rcu annotations
radix-tree: Add rcu_dereference and rcu_assign_pointer calls
radix tree test suite: Run iteration tests for longer
radix tree test suite: Fix split/join memory leaks
radix tree test suite: Fix leaks in regression2.c
radix tree test suite: Fix leaky tests
radix tree test suite: Enable address sanitizer
radix_tree_iter_resume: Fix out of bounds error
radix-tree: Store a pointer to the root in each node
radix-tree: Chain preallocated nodes through ->parent
radix tree test suite: Dial down verbosity with -v
radix tree test suite: Introduce kmalloc_verbose
idr: Return the deleted entry from idr_remove
radix tree test suite: Build separate binaries for some tests
ida: Use exceptional entries for small IDAs
ida: Move ida_bitmap to a percpu variable
Reimplement IDR and IDA using the radix tree
radix-tree: Add radix_tree_iter_delete
...
This patch makes arch-independent testcases for RODATA. Both x86 and
x86_64 already have testcases for RODATA, But they are arch-specific
because using inline assembly directly.
And cacheflush.h is not a suitable location for rodata-test related
things. Since they were in cacheflush.h, If someone change the state of
CONFIG_DEBUG_RODATA_TEST, It cause overhead of kernel build.
To solve the above issues, write arch-independent testcases and move it
to shared location.
[jinb.park7@gmail.com: fix config dependency]
Link: http://lkml.kernel.org/r/20170209131625.GA16954@pjb1027-Latitude-E5410
Link: http://lkml.kernel.org/r/20170129105436.GA9303@pjb1027-Latitude-E5410
Signed-off-by: Jinbum Park <jinb.park7@gmail.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 4a9d4b024a ("switch fput to task_work_add") implements a
schedule_work() for completing fput(), but did not guarantee calling
__fput() after unpacking initramfs. Because of this, there is a
possibility that during boot a driver can see ETXTBSY when it tries to
load a binary from initramfs as fput() is still pending on that binary.
This patch makes sure that fput() is completed after unpacking initramfs
and removes the call to flush_delayed_fput() in kernel_init() which
happens very late after unpacking initramfs.
Link: http://lkml.kernel.org/r/20170201140540.22051-1-lokeshvutla@ti.com
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reported-by: Murali Karicheri <m-karicheri2@ti.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull printk updates from Petr Mladek:
- Add Petr Mladek, Sergey Senozhatsky as printk maintainers, and Steven
Rostedt as the printk reviewer. This idea came up after the
discussion about printk issues at Kernel Summit. It was formulated
and discussed at lkml[1].
- Extend a lock-less NMI per-cpu buffers idea to handle recursive
printk() calls by Sergey Senozhatsky[2]. It is the first step in
sanitizing printk as discussed at Kernel Summit.
The change allows to see messages that would normally get ignored or
would cause a deadlock.
Also it allows to enable lockdep in printk(). This already paid off.
The testing in linux-next helped to discover two old problems that
were hidden before[3][4].
- Remove unused parameter by Sergey Senozhatsky. Clean up after a past
change.
[1] http://lkml.kernel.org/r/1481798878-31898-1-git-send-email-pmladek@suse.com
[2] http://lkml.kernel.org/r/20161227141611.940-1-sergey.senozhatsky@gmail.com
[3] http://lkml.kernel.org/r/20170215044332.30449-1-sergey.senozhatsky@gmail.com
[4] http://lkml.kernel.org/r/20170217015932.11898-1-sergey.senozhatsky@gmail.com
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
printk: drop call_console_drivers() unused param
printk: convert the rest to printk-safe
printk: remove zap_locks() function
printk: use printk_safe buffers in printk
printk: report lost messages in printk safe/nmi contexts
printk: always use deferred printk when flush printk_safe lines
printk: introduce per-cpu safe_print seq buffer
printk: rename nmi.c and exported api
printk: use vprintk_func in vprintk()
MAINTAINERS: Add printk maintainers
CONFIG_SET_MODULE_RONX to the more sensible CONFIG_STRICT_KERNEL_RWX and
CONFIG_STRICT_MODULE_RWX.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=7KhR
-----END PGP SIGNATURE-----
Merge tag 'rodata-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull rodata updates from Kees Cook:
"This renames the (now inaccurate) DEBUG_RODATA and related
SET_MODULE_RONX configs to the more sensible STRICT_KERNEL_RWX and
STRICT_MODULE_RWX"
* tag 'rodata-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
arch: Rename CONFIG_DEBUG_RODATA and CONFIG_DEBUG_MODULE_RONX
arch: Move CONFIG_DEBUG_RODATA and CONFIG_SET_MODULE_RONX to be common
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RK2h
-----END PGP SIGNATURE-----
Merge tag 'extable-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull exception table module split from Paul Gortmaker:
"Final extable.h related changes.
This completes the separation of exception table content from the
module.h header file. This is achieved with the final commit that
removes the one line back compatible change that sourced extable.h
into the module.h file.
The commits are unchanged since January, with the exception of a
couple Acks that came in for the last two commits a bit later. The
changes have been in linux-next for quite some time[1] and have got
widespread arch coverage via toolchains I have and also from
additional ones the kbuild bot has.
Maintaners of the various arch were Cc'd during the postings to
lkml[2] and informed that the intention was to take the remaining arch
specific changes and lump them together with the final two non-arch
specific changes and submit for this merge window.
The ia64 diffstat stands out and probably warrants a mention. In an
earlier review, Al Viro made a valid comment that the original header
separation of content left something to be desired, and that it get
fixed as a part of this change, hence the larger diffstat"
* tag 'extable-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (21 commits)
module.h: remove extable.h include now users have migrated
core: migrate exception table users off module.h and onto extable.h
cris: migrate exception table users off module.h and onto extable.h
hexagon: migrate exception table users off module.h and onto extable.h
microblaze: migrate exception table users off module.h and onto extable.h
unicore32: migrate exception table users off module.h and onto extable.h
score: migrate exception table users off module.h and onto extable.h
metag: migrate exception table users off module.h and onto extable.h
arc: migrate exception table users off module.h and onto extable.h
nios2: migrate exception table users off module.h and onto extable.h
sparc: migrate exception table users onto extable.h
openrisc: migrate exception table users off module.h and onto extable.h
frv: migrate exception table users off module.h and onto extable.h
sh: migrate exception table users off module.h and onto extable.h
xtensa: migrate exception table users off module.h and onto extable.h
mn10300: migrate exception table users off module.h and onto extable.h
alpha: migrate exception table users off module.h and onto extable.h
arm: migrate exception table users off module.h and onto extable.h
m32r: migrate exception table users off module.h and onto extable.h
ia64: ensure exception table search users include extable.h
...
Pull scheduler updates from Ingo Molnar:
"The main changes in this (fairly busy) cycle were:
- There was a class of scheduler bugs related to forgetting to update
the rq-clock timestamp which can cause weird and hard to debug
problems, so there's a new debug facility for this: which uncovered
a whole lot of bugs which convinced us that we want to keep the
debug facility.
(Peter Zijlstra, Matt Fleming)
- Various cputime related updates: eliminate cputime and use u64
nanoseconds directly, simplify and improve the arch interfaces,
implement delayed accounting more widely, etc. - (Frederic
Weisbecker)
- Move code around for better structure plus cleanups (Ingo Molnar)
- Move IO schedule accounting deeper into the scheduler plus related
changes to improve the situation (Tejun Heo)
- ... plus a round of sched/rt and sched/deadline fixes, plus other
fixes, updats and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (85 commits)
sched/core: Remove unlikely() annotation from sched_move_task()
sched/autogroup: Rename auto_group.[ch] to autogroup.[ch]
sched/topology: Split out scheduler topology code from core.c into topology.c
sched/core: Remove unnecessary #include headers
sched/rq_clock: Consolidate the ordering of the rq_clock methods
delayacct: Include <uapi/linux/taskstats.h>
sched/core: Clean up comments
sched/rt: Show the 'sched_rr_timeslice' SCHED_RR timeslice tuning knob in milliseconds
sched/clock: Add dummy clear_sched_clock_stable() stub function
sched/cputime: Remove generic asm headers
sched/cputime: Remove unused nsec_to_cputime()
s390, sched/cputime: Remove unused cputime definitions
powerpc, sched/cputime: Remove unused cputime definitions
s390, sched/cputime: Make arch_cpu_idle_time() to return nsecs
ia64, sched/cputime: Remove unused cputime definitions
ia64: Convert vtime to use nsec units directly
ia64, sched/cputime: Move the nsecs based cputime headers to the last arch using it
sched/cputime: Remove jiffies based cputime
sched/cputime, vtime: Return nsecs instead of cputime_t to account
sched/cputime: Complete nsec conversion of tick based accounting
...
The IDR is very similar to the radix tree. It has some functionality that
the radix tree did not have (alloc next free, cyclic allocation, a
callback-based for_each, destroy tree), which is readily implementable on
top of the radix tree. A few small changes were needed in order to use a
tag to represent nodes with free space below them. More extensive
changes were needed to support storing NULL as a valid entry in an IDR.
Plain radix trees still interpret NULL as a not-present entry.
The IDA is reimplemented as a client of the newly enhanced radix tree. As
in the current implementation, it uses a bitmap at the last level of the
tree.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Tested-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
These files were including module.h for exception table related
functions. We've now separated that content out into its own file
"extable.h" so now move over to that and where possible, avoid all
the extra header content in module.h that we don't really need to
compile these non-modular files.
Note:
init/main.c still needs module.h for __init_or_module
kernel/extable.c still needs module.h for is_module_text_address
...and so we don't get the benefit of removing module.h from the cpp
feed for these two files, unlike the almost universal 1:1 exchange
of module.h for extable.h we were able to do in the arch dirs.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Jessica Yu <jeyu@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
A preparation patch for printk_safe work. No functional change.
- rename nmi.c to print_safe.c
- add `printk_safe' prefix to some (which used both by printk-safe
and printk-nmi) of the exported functions.
Link: http://lkml.kernel.org/r/20161227141611.940-3-sergey.senozhatsky@gmail.com
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: Calvin Owens <calvinowens@fb.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Both of these options are poorly named. The features they provide are
necessary for system security and should not be considered debug only.
Change the names to CONFIG_STRICT_KERNEL_RWX and
CONFIG_STRICT_MODULE_RWX to better describe what these options do.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Jessica Yu <jeyu@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Before invoking the arch specific handler, efi_mem_reserve() reserves
the given memory region through memblock.
efi_bgrt_init() will call efi_mem_reserve() after mm_init(), at which
time memblock is dead and should not be used anymore.
The EFI BGRT code depends on ACPI initialization to get the BGRT ACPI
table, so move parsing of the BGRT table to ACPI early boot code to
ensure that efi_mem_reserve() in EFI BGRT code still use memblock safely.
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-acpi@vger.kernel.org
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1485868902-20401-9-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that our crng uses chacha20, we can rely on its speedy
characteristics for replacing MD5, while simultaneously achieving a
higher security guarantee. Before the idea was to use these functions if
you wanted random integers that aren't stupidly insecure but aren't
necessarily secure either, a vague gray zone, that hopefully was "good
enough" for its users. With chacha20, we can strengthen this claim,
since either we're using an rdrand-like instruction, or we're using the
same crng as /dev/urandom. And it's faster than what was before.
We could have chosen to replace this with a SipHash-derived function,
which might be slightly faster, but at the cost of having yet another
RNG construction in the kernel. By moving to chacha20, we have a single
RNG to analyze and verify, and we also already get good performance
improvements on all platforms.
Implementation-wise, rather than use a generic buffer for both
get_random_int/long and memcpy based on the size needs, we use a
specific buffer for 32-bit reads and for 64-bit reads. This way, we're
guaranteed to always have aligned accesses on all platforms. While
slightly more verbose in C, the assembly this generates is a lot
simpler than otherwise.
Finally, on 32-bit platforms where longs and ints are the same size,
we simply alias get_random_int to get_random_long.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Suggested-by: Theodore Ts'o <tytso@mit.edu>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Currently we switch to the stable sched_clock if we guess the TSC is
usable, and then switch back to the unstable path if it turns out TSC
isn't stable during SMP bringup after all.
Delay switching to the stable path until after SMP bringup is
complete. This way we'll avoid switching during the time we detect the
worst of the TSC offences.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a new page flag, PageWaiters, to indicate the page waitqueue has
tasks waiting. This can be tested rather than testing waitqueue_active
which requires another cacheline load.
This bit is always set when the page has tasks on page_waitqueue(page),
and is set and cleared under the waitqueue lock. It may be set when
there are no tasks on the waitqueue, which will cause a harmless extra
wakeup check that will clears the bit.
The generic bit-waitqueue infrastructure is no longer used for pages.
Instead, waitqueues are used directly with a custom key type. The
generic code was not flexible enough to have PageWaiters manipulation
under the waitqueue lock (which simplifies concurrency).
This improves the performance of page lock intensive microbenchmarks by
2-3%.
Putting two bits in the same word opens the opportunity to remove the
memory barrier between clearing the lock bit and testing the waiters
bit, after some work on the arch primitives (e.g., ensuring memory
operand widths match and cover both bits).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Summary of modules changes for the 4.10 merge window:
* The rodata= cmdline parameter has been extended to additionally
apply to module mappings
* Fix a hard to hit race between module loader error/clean up
handling and ftrace registration
* Some code cleanups, notably panic.c and modules code use a
unified taint_flags table now. This is much cleaner than
duplicating the taint flag code in modules.c
Signed-off-by: Jessica Yu <jeyu@redhat.com>
-----BEGIN PGP SIGNATURE-----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=bhCS
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull modules updates from Jessica Yu:
"Summary of modules changes for the 4.10 merge window:
- The rodata= cmdline parameter has been extended to additionally
apply to module mappings
- Fix a hard to hit race between module loader error/clean up
handling and ftrace registration
- Some code cleanups, notably panic.c and modules code use a unified
taint_flags table now. This is much cleaner than duplicating the
taint flag code in modules.c"
* tag 'modules-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: fix DEBUG_SET_MODULE_RONX typo
module: extend 'rodata=off' boot cmdline parameter to module mappings
module: Fix a comment above strong_try_module_get()
module: When modifying a module's text ignore modules which are going away too
module: Ensure a module's state is set accordingly during module coming cleanup code
module: remove trailing whitespace
taint/module: Clean up global and module taint flags handling
modpost: free allocated memory
Pull workqueue updates from Tejun Heo:
"Mostly patches to initialize workqueue subsystem earlier and get rid
of keventd_up().
The patches were headed for the last merge cycle but got delayed due
to a bug found late minute, which is fixed now.
Also, to help debugging, destroy_workqueue() is more chatty now on a
sanity check failure."
* 'for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: move wq_numa_init() to workqueue_init()
workqueue: remove keventd_up()
debugobj, workqueue: remove keventd_up() usage
slab, workqueue: remove keventd_up() usage
power, workqueue: remove keventd_up() usage
tty, workqueue: remove keventd_up() usage
mce, workqueue: remove keventd_up() usage
workqueue: make workqueue available early during boot
workqueue: dump workqueue state on sanity check failures in destroy_workqueue()
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but should be
more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to go...
Lots of plain-text files have also been converted and integrated.
- Images in binary formats have been replaced with more source-friendly
versions.
- Various bits of organizational work, including the renaming of various
files discussed at the kernel summit.
- New documentation for the device_link mechanism.
...and, of course, lots of typo fixes and small updates.
-----BEGIN PGP SIGNATURE-----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=A0EV
-----END PGP SIGNATURE-----
Merge tag 'docs-4.10' of git://git.lwn.net/linux
Pull documentation update from Jonathan Corbet:
"These are the documentation changes for 4.10.
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but
should be more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to
go... Lots of plain-text files have also been converted and
integrated.
- Images in binary formats have been replaced with more
source-friendly versions.
- Various bits of organizational work, including the renaming of
various files discussed at the kernel summit.
- New documentation for the device_link mechanism.
... and, of course, lots of typo fixes and small updates"
* tag 'docs-4.10' of git://git.lwn.net/linux: (193 commits)
dma-buf: Extract dma-buf.rst
Update Documentation/00-INDEX
docs: 00-INDEX: document directories/files with no docs
docs: 00-INDEX: remove non-existing entries
docs: 00-INDEX: add missing entries for documentation files/dirs
docs: 00-INDEX: consolidate process/ and admin-guide/ description
scripts: add a script to check if Documentation/00-INDEX is sane
Docs: change sh -> awk in REPORTING-BUGS
Documentation/core-api/device_link: Add initial documentation
core-api: remove an unexpected unident
ppc/idle: Add documentation for powersave=off
Doc: Correct typo, "Introdution" => "Introduction"
Documentation/atomic_ops.txt: convert to ReST markup
Documentation/local_ops.txt: convert to ReST markup
Documentation/assoc_array.txt: convert to ReST markup
docs-rst: parse-headers.pl: cleanup the documentation
docs-rst: fix media cleandocs target
docs-rst: media/Makefile: reorganize the rules
docs-rst: media: build SVG from graphviz files
docs-rst: replace bayer.png by a SVG image
...
AMD CPUs affected by the E400 erratum suffer from the issue that the
local APIC timer stops when the CPU goes into C1E. Unfortunately there
is no way to detect the affected CPUs on early boot. It's only possible
to determine the range of possibly affected CPUs from the family/model
range.
The actual decision whether to enter C1E and thus cause the bug is done
by the firmware and we need to detect that case late, after ACPI has
been initialized.
The current solution is to check in the idle routine whether the CPU is
affected by reading the MSR_K8_INT_PENDING_MSG MSR and checking for the
K8_INTP_C1E_ACTIVE_MASK bits. If one of the bits is set then the CPU is
affected and the system is switched into forced broadcast mode.
This is ineffective and on non-affected CPUs every entry to idle does
the extra RDMSR.
After doing some research it turns out that the bits are visible on the
boot CPU right after the ACPI subsystem is initialized in the early
boot process. So instead of polling for the bits in the idle loop, add
a detection function after acpi_subsystem_init() and check for the MSR
bits. If set, then the X86_BUG_AMD_APIC_C1E is set on the boot CPU and
the TSC is marked unstable when X86_FEATURE_NONSTOP_TSC is not set as it
will stop in C1E state as well.
The switch to broadcast mode cannot be done at this point because the
boot CPU still uses HPET as a clockevent device and the local APIC timer
is not yet calibrated and installed. The switch to broadcast mode on the
affected CPUs needs to be done when the local APIC timer is actually set
up.
This allows to cleanup the amd_e400_idle() function in the next step.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20161209182912.2726-4-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The newly added 'rodata_enabled' global variable is protected by
the wrong #ifdef, leading to a link error when CONFIG_DEBUG_SET_MODULE_RONX
is turned on:
kernel/module.o: In function `disable_ro_nx':
module.c:(.text.unlikely.disable_ro_nx+0x88): undefined reference to `rodata_enabled'
kernel/module.o: In function `module_disable_ro':
module.c:(.text.module_disable_ro+0x8c): undefined reference to `rodata_enabled'
kernel/module.o: In function `module_enable_ro':
module.c:(.text.module_enable_ro+0xb0): undefined reference to `rodata_enabled'
CONFIG_SET_MODULE_RONX does not exist, so use the correct one instead.
Fixes: 39290b389e ("module: extend 'rodata=off' boot cmdline parameter to module mappings")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jessica Yu <jeyu@redhat.com>
The current "rodata=off" parameter disables read-only kernel mappings
under CONFIG_DEBUG_RODATA:
commit d2aa1acad2 ("mm/init: Add 'rodata=off' boot cmdline parameter
to disable read-only kernel mappings")
This patch is a logical extension to module mappings ie. read-only mappings
at module loading can be disabled even if CONFIG_DEBUG_SET_MODULE_RONX
(mainly for debug use). Please note, however, that it only affects RO/RW
permissions, keeping NX set.
This is the first step to make CONFIG_DEBUG_SET_MODULE_RONX mandatory
(always-on) in the future as CONFIG_DEBUG_RODATA on x86 and arm64.
Suggested-by: and Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Link: http://lkml.kernel.org/r/20161114061505.15238-1-takahiro.akashi@linaro.org
Signed-off-by: Jessica Yu <jeyu@redhat.com>
The previous patch renamed several files that are cross-referenced
along the Kernel documentation. Adjust the links to point to
the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds a new gcc plugin named "latent_entropy". It is designed to
extract as much possible uncertainty from a running system at boot time as
possible, hoping to capitalize on any possible variation in CPU operation
(due to runtime data differences, hardware differences, SMP ordering,
thermal timing variation, cache behavior, etc).
At the very least, this plugin is a much more comprehensive example for
how to manipulate kernel code using the gcc plugin internals.
The need for very-early boot entropy tends to be very architecture or
system design specific, so this plugin is more suited for those sorts
of special cases. The existing kernel RNG already attempts to extract
entropy from reliable runtime variation, but this plugin takes the idea to
a logical extreme by permuting a global variable based on any variation
in code execution (e.g. a different value (and permutation function)
is used to permute the global based on loop count, case statement,
if/then/else branching, etc).
To do this, the plugin starts by inserting a local variable in every
marked function. The plugin then adds logic so that the value of this
variable is modified by randomly chosen operations (add, xor and rol) and
random values (gcc generates separate static values for each location at
compile time and also injects the stack pointer at runtime). The resulting
value depends on the control flow path (e.g., loops and branches taken).
Before the function returns, the plugin mixes this local variable into
the latent_entropy global variable. The value of this global variable
is added to the kernel entropy pool in do_one_initcall() and _do_fork(),
though it does not credit any bytes of entropy to the pool; the contents
of the global are just used to mix the pool.
Additionally, the plugin can pre-initialize arrays with build-time
random contents, so that two different kernel builds running on identical
hardware will not have the same starting values.
Signed-off-by: Emese Revfy <re.emese@gmail.com>
[kees: expanded commit message and code comments]
Signed-off-by: Kees Cook <keescook@chromium.org>
Workqueue is currently initialized in an early init call; however,
there are cases where early boot code has to be split and reordered to
come after workqueue initialization or the same code path which makes
use of workqueues is used both before workqueue initailization and
after. The latter cases have to gate workqueue usages with
keventd_up() tests, which is nasty and easy to get wrong.
Workqueue usages have become widespread and it'd be a lot more
convenient if it can be used very early from boot. This patch splits
workqueue initialization into two steps. workqueue_init_early() which
sets up the basic data structures so that workqueues can be created
and work items queued, and workqueue_init() which actually brings up
workqueues online and starts executing queued work items. The former
step can be done very early during boot once memory allocation,
cpumasks and idr are initialized. The latter right after kthreads
become available.
This allows work item queueing and canceling from very early boot
which is what most of these use cases want.
* As systemd_wq being initialized doesn't indicate that workqueue is
fully online anymore, update keventd_up() to test wq_online instead.
The follow-up patches will get rid of all its usages and the
function itself.
* Flushing doesn't make sense before workqueue is fully initialized.
The flush functions trigger WARN and return immediately before fully
online.
* Work items are never in-flight before fully online. Canceling can
always succeed by skipping the flush step.
* Some code paths can no longer assume to be called with irq enabled
as irq is disabled during early boot. Use irqsave/restore
operations instead.
v2: Watchdog init, which requires timer to be running, moved from
workqueue_init_early() to workqueue_init().
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/CA+55aFx0vPuMuxn00rBSM192n-Du5uxy+4AvKa0SBSOVJeuCGg@mail.gmail.com
sprint_symbol_no_offset() returns the string "function_name
[module_name]" where [module_name] is not printed for built in kernel
functions. This means that the blacklisting code will fail when
comparing module function names with the extended string.
This patch adds the functionality to block a module's module_init()
function by finding the space in the string and truncating the
comparison to that length.
Link: http://lkml.kernel.org/r/1466124387-20446-1-git-send-email-prarit@redhat.com
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yang Shi <yang.shi@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Kees Cook <keescook@chromium.org>
Cc: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was only one use of __initdata_refok and __exit_refok
__init_refok was used 46 times against 82 for __ref.
Those definitions are obsolete since commit 312b1485fb ("Introduce new
section reference annotations tags: __ref, __refdata, __refconst")
This patch removes the following compatibility definitions and replaces
them treewide.
/* compatibility defines */
#define __init_refok __ref
#define __initdata_refok __refdata
#define __exit_refok __ref
I can also provide separate patches if necessary.
(One patch per tree and check in 1 month or 2 to remove old definitions)
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1466796271-3043-1-git-send-email-fabf@skynet.be
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge misc fixes from Andrew Morton:
"Two weeks worth of fixes here"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (41 commits)
init/main.c: fix initcall_blacklisted on ia64, ppc64 and parisc64
autofs: don't get stuck in a loop if vfs_write() returns an error
mm/page_owner: avoid null pointer dereference
tools/vm/slabinfo: fix spelling mistake: "Ocurrences" -> "Occurrences"
fs/nilfs2: fix potential underflow in call to crc32_le
oom, suspend: fix oom_reaper vs. oom_killer_disable race
ocfs2: disable BUG assertions in reading blocks
mm, compaction: abort free scanner if split fails
mm: prevent KASAN false positives in kmemleak
mm/hugetlb: clear compound_mapcount when freeing gigantic pages
mm/swap.c: flush lru pvecs on compound page arrival
memcg: css_alloc should return an ERR_PTR value on error
memcg: mem_cgroup_migrate() may be called with irq disabled
hugetlb: fix nr_pmds accounting with shared page tables
Revert "mm: disable fault around on emulated access bit architecture"
Revert "mm: make faultaround produce old ptes"
mailmap: add Boris Brezillon's email
mailmap: add Antoine Tenart's email
mm, sl[au]b: add __GFP_ATOMIC to the GFP reclaim mask
mm: mempool: kasan: don't poot mempool objects in quarantine
...
When I replaced kasprintf("%pf") with a direct call to
sprint_symbol_no_offset I must have broken the initcall blacklisting
feature on the arches where dereference_function_descriptor() is
non-trivial.
Fixes: c8cdd2be21 (init/main.c: simplify initcall_blacklisted())
Link: http://lkml.kernel.org/r/1466027283-4065-1-git-send-email-linux@rasmusvillemoes.dk
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Yang Shi <yang.shi@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Petr Mladek <pmladek@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We've had the thread info allocated together with the thread stack for
most architectures for a long time (since the thread_info was split off
from the task struct), but that is about to change.
But the patches that move the thread info to be off-stack (and a part of
the task struct instead) made it clear how confused the allocator and
freeing functions are.
Because the common case was that we share an allocation with the thread
stack and the thread_info, the two pointers were identical. That
identity then meant that we would have things like
ti = alloc_thread_info_node(tsk, node);
...
tsk->stack = ti;
which certainly _worked_ (since stack and thread_info have the same
value), but is rather confusing: why are we assigning a thread_info to
the stack? And if we move the thread_info away, the "confusing" code
just gets to be entirely bogus.
So remove all this confusion, and make it clear that we are doing the
stack allocation by renaming and clarifying the function names to be
about the stack. The fact that the thread_info then shares the
allocation is an implementation detail, and not really about the
allocation itself.
This is a pure renaming and type fix: we pass in the same pointer, it's
just that we clarify what the pointer means.
The ia64 code that actually only has one single allocation (for all of
task_struct, thread_info and kernel thread stack) now looks a bit odd,
but since "tsk->stack" is actually not even used there, that oddity
doesn't matter. It would be a separate thing to clean that up, I
intentionally left the ia64 changes as a pure brute-force renaming and
type change.
Acked-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
page_ext_init() checks suitable pages with pfn_to_nid(), but
pfn_to_nid() depends on memmap which will not be setup fully until
page_alloc_init_late() is done. Use early_pfn_to_nid() instead of
pfn_to_nid() so that page extension could be still used early even
though CONFIG_ DEFERRED_STRUCT_PAGE_INIT is enabled and catch early page
allocation call sites.
Suggested by Joonsoo Kim [1], this fix basically undoes the change
introduced by commit b8f1a75d61 ("mm: call page_ext_init() after all
struct pages are initialized") and fixes the same problem with a better
approach.
[1] http://lkml.kernel.org/r/CAAmzW4OUmyPwQjvd7QUfc6W1Aic__TyAuH80MLRZNMxKy0-wPQ@mail.gmail.com
Link: http://lkml.kernel.org/r/1464198689-23458-1-git-send-email-yang.shi@linaro.org
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using kasprintf to get the function name makes us look up the name
twice, along with all the vsnprintf overhead of parsing the format
string etc. It also means there is an allocation failure case to deal
with. Since symbol_string in vsprintf.c would anyway allocate an array
of size KSYM_SYMBOL_LEN on the stack, that might as well be done up
here.
Moreover, since this is a debug feature and the blacklisted_initcalls
list is usually empty, we might as well test that and thus avoid looking
up the symbol name even once in the common case.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Prarit Bhargava <prarit@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
printk() takes some locks and could not be used a safe way in NMI
context.
The chance of a deadlock is real especially when printing stacks from
all CPUs. This particular problem has been addressed on x86 by the
commit a9edc88093 ("x86/nmi: Perform a safe NMI stack trace on all
CPUs").
The patchset brings two big advantages. First, it makes the NMI
backtraces safe on all architectures for free. Second, it makes all NMI
messages almost safe on all architectures (the temporary buffer is
limited. We still should keep the number of messages in NMI context at
minimum).
Note that there already are several messages printed in NMI context:
WARN_ON(in_nmi()), BUG_ON(in_nmi()), anything being printed out from MCE
handlers. These are not easy to avoid.
This patch reuses most of the code and makes it generic. It is useful
for all messages and architectures that support NMI.
The alternative printk_func is set when entering and is reseted when
leaving NMI context. It queues IRQ work to copy the messages into the
main ring buffer in a safe context.
__printk_nmi_flush() copies all available messages and reset the buffer.
Then we could use a simple cmpxchg operations to get synchronized with
writers. There is also used a spinlock to get synchronized with other
flushers.
We do not longer use seq_buf because it depends on external lock. It
would be hard to make all supported operations safe for a lockless use.
It would be confusing and error prone to make only some operations safe.
The code is put into separate printk/nmi.c as suggested by Steven
Rostedt. It needs a per-CPU buffer and is compiled only on
architectures that call nmi_enter(). This is achieved by the new
HAVE_NMI Kconfig flag.
The are MN10300 and Xtensa architectures. We need to clean up NMI
handling there first. Let's do it separately.
The patch is heavily based on the draft from Peter Zijlstra, see
https://lkml.org/lkml/2015/6/10/327
[arnd@arndb.de: printk-nmi: use %zu format string for size_t]
[akpm@linux-foundation.org: min_t->min - all types are size_t here]
Signed-off-by: Petr Mladek <pmladek@suse.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Jan Kara <jack@suse.cz>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> [arm part]
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jiri Kosina <jkosina@suse.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: David Miller <davem@davemloft.net>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge first patch-bomb from Andrew Morton:
- some misc things
- ofs2 updates
- about half of MM
- checkpatch updates
- autofs4 update
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (120 commits)
autofs4: fix string.h include in auto_dev-ioctl.h
autofs4: use pr_xxx() macros directly for logging
autofs4: change log print macros to not insert newline
autofs4: make autofs log prints consistent
autofs4: fix some white space errors
autofs4: fix invalid ioctl return in autofs4_root_ioctl_unlocked()
autofs4: fix coding style line length in autofs4_wait()
autofs4: fix coding style problem in autofs4_get_set_timeout()
autofs4: coding style fixes
autofs: show pipe inode in mount options
kallsyms: add support for relative offsets in kallsyms address table
kallsyms: don't overload absolute symbol type for percpu symbols
x86: kallsyms: disable absolute percpu symbols on !SMP
checkpatch: fix another left brace warning
checkpatch: improve UNSPECIFIED_INT test for bare signed/unsigned uses
checkpatch: warn on bare unsigned or signed declarations without int
checkpatch: exclude asm volatile from complex macro check
mm: memcontrol: drop unnecessary lru locking from mem_cgroup_migrate()
mm: migrate: consolidate mem_cgroup_migrate() calls
mm/compaction: speed up pageblock_pfn_to_page() when zone is contiguous
...
Use list_for_each_entry() instead of list_for_each() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull cpu hotplug updates from Thomas Gleixner:
"This is the first part of the ongoing cpu hotplug rework:
- Initial implementation of the state machine
- Runs all online and prepare down callbacks on the plugged cpu and
not on some random processor
- Replaces busy loop waiting with completions
- Adds tracepoints so the states can be followed"
More detailed commentary on this work from an earlier email:
"What's wrong with the current cpu hotplug infrastructure?
- Asymmetry
The hotplug notifier mechanism is asymmetric versus the bringup and
teardown. This is mostly caused by the notifier mechanism.
- Largely undocumented dependencies
While some notifiers use explicitely defined notifier priorities,
we have quite some notifiers which use numerical priorities to
express dependencies without any documentation why.
- Control processor driven
Most of the bringup/teardown of a cpu is driven by a control
processor. While it is understandable, that preperatory steps,
like idle thread creation, memory allocation for and initialization
of essential facilities needs to be done before a cpu can boot,
there is no reason why everything else must run on a control
processor. Before this patch series, bringup looks like this:
Control CPU Booting CPU
do preparatory steps
kick cpu into life
do low level init
sync with booting cpu sync with control cpu
bring the rest up
- All or nothing approach
There is no way to do partial bringups. That's something which is
really desired because we waste e.g. at boot substantial amount of
time just busy waiting that the cpu comes to life. That's stupid
as we could very well do preparatory steps and the initial IPI for
other cpus and then go back and do the necessary low level
synchronization with the freshly booted cpu.
- Minimal debuggability
Due to the notifier based design, it's impossible to switch between
two stages of the bringup/teardown back and forth in order to test
the correctness. So in many hotplug notifiers the cancel
mechanisms are either not existant or completely untested.
- Notifier [un]registering is tedious
To [un]register notifiers we need to protect against hotplug at
every callsite. There is no mechanism that bringup/teardown
callbacks are issued on the online cpus, so every caller needs to
do it itself. That also includes error rollback.
What's the new design?
The base of the new design is a symmetric state machine, where both
the control processor and the booting/dying cpu execute a well
defined set of states. Each state is symmetric in the end, except
for some well defined exceptions, and the bringup/teardown can be
stopped and reversed at almost all states.
So the bringup of a cpu will look like this in the future:
Control CPU Booting CPU
do preparatory steps
kick cpu into life
do low level init
sync with booting cpu sync with control cpu
bring itself up
The synchronization step does not require the control cpu to wait.
That mechanism can be done asynchronously via a worker or some
other mechanism.
The teardown can be made very similar, so that the dying cpu cleans
up and brings itself down. Cleanups which need to be done after
the cpu is gone, can be scheduled asynchronously as well.
There is a long way to this, as we need to refactor the notion when a
cpu is available. Today we set the cpu online right after it comes
out of the low level bringup, which is not really correct.
The proper mechanism is to set it to available, i.e. cpu local
threads, like softirqd, hotplug thread etc. can be scheduled on that
cpu, and once it finished all booting steps, it's set to online, so
general workloads can be scheduled on it. The reverse happens on
teardown. First thing to do is to forbid scheduling of general
workloads, then teardown all the per cpu resources and finally shut it
off completely.
This patch series implements the basic infrastructure for this at the
core level. This includes the following:
- Basic state machine implementation with well defined states, so
ordering and prioritization can be expressed.
- Interfaces to [un]register state callbacks
This invokes the bringup/teardown callback on all online cpus with
the proper protection in place and [un]installs the callbacks in
the state machine array.
For callbacks which have no particular ordering requirement we have
a dynamic state space, so that drivers don't have to register an
explicit hotplug state.
If a callback fails, the code automatically does a rollback to the
previous state.
- Sysfs interface to drive the state machine to a particular step.
This is only partially functional today. Full functionality and
therefor testability will be achieved once we converted all
existing hotplug notifiers over to the new scheme.
- Run all CPU_ONLINE/DOWN_PREPARE notifiers on the booting/dying
processor:
Control CPU Booting CPU
do preparatory steps
kick cpu into life
do low level init
sync with booting cpu sync with control cpu
wait for boot
bring itself up
Signal completion to control cpu
In a previous step of this work we've done a full tree mechanical
conversion of all hotplug notifiers to the new scheme. The balance
is a net removal of about 4000 lines of code.
This is not included in this series, as we decided to take a
different approach. Instead of mechanically converting everything
over, we will do a proper overhaul of the usage sites one by one so
they nicely fit into the symmetric callback scheme.
I decided to do that after I looked at the ugliness of some of the
converted sites and figured out that their hotplug mechanism is
completely buggered anyway. So there is no point to do a
mechanical conversion first as we need to go through the usage
sites one by one again in order to achieve a full symmetric and
testable behaviour"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
cpu/hotplug: Document states better
cpu/hotplug: Fix smpboot thread ordering
cpu/hotplug: Remove redundant state check
cpu/hotplug: Plug death reporting race
rcu: Make CPU_DYING_IDLE an explicit call
cpu/hotplug: Make wait for dead cpu completion based
cpu/hotplug: Let upcoming cpu bring itself fully up
arch/hotplug: Call into idle with a proper state
cpu/hotplug: Move online calls to hotplugged cpu
cpu/hotplug: Create hotplug threads
cpu/hotplug: Split out the state walk into functions
cpu/hotplug: Unpark smpboot threads from the state machine
cpu/hotplug: Move scheduler cpu_online notifier to hotplug core
cpu/hotplug: Implement setup/removal interface
cpu/hotplug: Make target state writeable
cpu/hotplug: Add sysfs state interface
cpu/hotplug: Hand in target state to _cpu_up/down
cpu/hotplug: Convert the hotplugged cpu work to a state machine
cpu/hotplug: Convert to a state machine for the control processor
cpu/hotplug: Add tracepoints
...
Pull read-only kernel memory updates from Ingo Molnar:
"This tree adds two (security related) enhancements to the kernel's
handling of read-only kernel memory:
- extend read-only kernel memory to a new class of formerly writable
kernel data: 'post-init read-only memory' via the __ro_after_init
attribute, and mark the ARM and x86 vDSO as such read-only memory.
This kind of attribute can be used for data that requires a once
per bootup initialization sequence, but is otherwise never modified
after that point.
This feature was based on the work by PaX Team and Brad Spengler.
(by Kees Cook, the ARM vDSO bits by David Brown.)
- make CONFIG_DEBUG_RODATA always enabled on x86 and remove the
Kconfig option. This simplifies the kernel and also signals that
read-only memory is the default model and a first-class citizen.
(Kees Cook)"
* 'mm-readonly-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ARM/vdso: Mark the vDSO code read-only after init
x86/vdso: Mark the vDSO code read-only after init
lkdtm: Verify that '__ro_after_init' works correctly
arch: Introduce post-init read-only memory
x86/mm: Always enable CONFIG_DEBUG_RODATA and remove the Kconfig option
mm/init: Add 'rodata=off' boot cmdline parameter to disable read-only kernel mappings
asm-generic: Consolidate mark_rodata_ro()
Handle the smpboot threads in the state machine.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182341.295777684@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the split out steps into a callback array and let the cpu_up/down
code iterate through the array functions. For now most of the
callbacks are asymmetric to resemble the current hotplug maze.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182340.671816690@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It may be useful to debug writes to the readonly sections of memory,
so provide a cmdline "rodata=off" to allow for this. This can be
expanded in the future to support "log" and "write" modes, but that
will need to be architecture-specific.
This also makes KDB software breakpoints more usable, as read-only
mappings can now be disabled on any kernel.
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Brown <david.brown@linaro.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Emese Revfy <re.emese@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathias Krause <minipli@googlemail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: PaX Team <pageexec@freemail.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-hardening@lists.openwall.com
Cc: linux-arch <linux-arch@vger.kernel.org>
Link: http://lkml.kernel.org/r/1455748879-21872-3-git-send-email-keescook@chromium.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Lockdep is initialized at compile time now. Get rid of lockdep_init().
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Krinkin <krinkin.m.u@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: mm-commits@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Make obsolete_checksetup() return bool due to this particular function
only using either one or zero as its return value.
No functional change.
Signed-off-by: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko