The global device lock is acquired to search the resource table.
The lock is actually itself part of the table (entry 0).
Therefore if someone asks for resource 0 we would deadlock since
double locking is no longer allowed.
Currently the driver doesn't try to lock that resource so let's
simply make sure we fail graciously and not add special handling
of this case until really need. Hide the relevant defines in
the source file.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP can be connected to multiple machines via PCI or other buses.
Access to hardware resources is arbitrated using locks residing
in device memory. Currently nfpcore only respects the mutexes
when it comes to inter-host locking, but if we try to acquire
the same lock again, on one host - it will simply return success
because owner of the lock is already set to that host.
This makes the locks useless for arbitration within one host
and unfair because whichever host grabbed the lock will have
a chance to reacquire it without others getting a shot.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset")
removed the bcmgenet_mii_reset() function from bcmgenet_power_up() and
bcmgenet_internal_phy_setup() functions. In so doing it broke the reset
of the internal PHY devices used by the GENETv1-GENETv3 which required
this reset before the UniMAC was enabled. It also broke the internal
GPHY devices used by the GENETv4 because the config_init that installed
the AFE workaround was no longer occurring after the reset of the GPHY
performed by bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup().
In addition the code in bcmgenet_internal_phy_setup() related to the
"enable APD" comment goes with the bcmgenet_mii_reset() so it should
have also been removed.
Commit bd4060a610 ("net: bcmgenet: Power on integrated GPHY in
bcmgenet_power_up()") moved the bcmgenet_phy_power_set() call to the
bcmgenet_power_up() function, but failed to remove it from the
bcmgenet_internal_phy_setup() function. Had it done so, the
bcmgenet_internal_phy_setup() function would have been empty and could
have been removed at that time.
Commit 5dbebbb44a ("net: bcmgenet: Software reset EPHY after power on")
was submitted to correct the functional problems introduced by
commit 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset"). It
was included in v4.4 and made available on 4.3-stable. Unfortunately,
it didn't fully revert the commit because this bcmgenet_mii_reset()
doesn't apply the soft reset to the internal GPHY used by GENETv4 like
the previous one did. This prevents the restoration of the AFE work-
arounds for internal GPHY devices after the bcmgenet_phy_power_set() in
bcmgenet_internal_phy_setup().
This commit takes the alternate approach of removing the unnecessary
bcmgenet_internal_phy_setup() function which shouldn't have been in v4.3
so that when bcmgenet_mii_reset() was restored it should have only gone
into bcmgenet_power_up(). This will avoid the problems while also
removing the redundancy (and hopefully some of the confusion).
Fixes: 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma_mapping_error() returns true if there is an error but we want
to return -ENOMEM and not 1.
Fixes: 65e0ace2c5 ("net: dwc-xlgmac: Initial driver for DesignWare Enterprise Ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jie Deng <jiedeng@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make mmd_phy_indirect() use the same terminology as the rest of the
code, making clear what each address is - phy address, devad, and
register number.
While here, remove the "inline" from this static function, leaving
it to the compiler to decide whether to inline this function, and
get rid of unnecessary parens.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the indirect MMD read/write methods which are now no longer
necessary.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert micrel to the new read_mmd/write_mmd driver methods. This
Clause 22 PHY does not support any MMD access method.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch everyone over to using phy_read_mmd() and phy_write_mmd() now
that they are able to handle both Clause 22 indirect addressing and
Clause 45 direct addressing methods to the MMD registers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan78xx appears to use phylib in a rather weird way, accessing the PHY
partly through phylib, and partly by making direct accesses to it,
including to the Clause 45 registers. As the indirect MMD accessors are
going away, update this driver to use the plain phy_(read|write)_mmd()
accessors instead.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make phy_(read|write)_mmd() generic 802.3 clause 45 register accessors
for both Clause 22 and Clause 45 PHYs, using either the direct register
reading for Clause 45, or the indirect method for Clause 22 PHYs.
Allow this behaviour to be overriden by PHY drivers where necessary.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the phy_(read|write)__mmd() helpers out of line, they will become
our main MMD accessor functions, and so will be a little more complex.
This complexity doesn't belong in an inline function. Also move the
_indirect variants as well to keep like functionality together.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The extended device socket cannot turn on/off while system is running.
So when system boots up and the device is not power on, the fjes driver
does not need be loaded.
To check the status of the device, the patch adds ACPI _STA method check.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
CC: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fjes driver is used only by FUJITSU servers and almost of all
servers in the world never use it. But currently if ACPI PNP0C02
is defined in the ACPI table, the following message is always shown:
"FUJITSU Extended Socket Network Device Driver - version 1.2
- Copyright (c) 2015 FUJITSU LIMITED"
The message makes users confused because there is no reason that
the message is shown in other vendor servers.
To avoid the confusion, the patch adds a check that the server
has a extended socket device or not.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
CC: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes to support multiple queues in the device tree bindings
resulted in the number of RX and TX queues to be initialized to zero for
device trees not adhering to the new bindings.
Restore backwards-compatibility with those device trees by falling back
to a single RX and TX queues each.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC RX queues always need to be enabled in order to receive network
packets. Remove the condition that this only needs to be done for multi-
queue configurations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX packets statistics ('rx_packets' counter) used to count LRO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'rx_lro_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 435277
rx_lro_packets: 35847
rx_packets_phy: 1935066
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 1935066
rx_lro_packets: 35847
rx_packets_phy: 1935066
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX packets statistics ('tx_packets' counter) used to count GSO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'tx_tso_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 61340
tx_tso_packets: 60954
tx_packets_phy: 2451115
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 2451115
tx_tso_packets: 60954
tx_packets_phy: 2451115
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ConnectX-4 sharing SRQs from the same space as QPs, we hit a
limit preventing some applications to allocate needed QPs amount.
Double the size to 256K.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was added to allow the TC offloading code to identify offloading
encap/decap vxlan rules.
The VF reps are effectively related to the same mlx5 PCI device as the
PF. Since the kernel invokes the (say) delete ndo for each netdev, the
FW erred on multiple vxlan dst port deletes when the port was deleted
from the system.
We fix that by keeping the registration to be carried out only by the
PF. Since the PF serves as the uplink device, the VF reps will look
up a port there and realize if they are ok to offload that.
Tested:
<SETUP VFS>
<SETUP switchdev mode to have representors>
ip link add vxlan1 type vxlan id 44 dev ens5f0 dstport 9999
ip link set vxlan1 up
ip link del dev vxlan1
Fixes: 4a25730eb2 ('net/mlx5e: Add ndo_udp_tunnel_add to VF representors')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use the non UAPI values and we miss erring on
the modify action which is not supported, fix that.
Fixes: 8b32580df1 ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the eswitch inline mode can potentially cause already configured
flows not to match the policy. E.g. set policy L4, add some L4 rules,
set policy to L2 --> bad! Hence we disallow it.
Keep track of how many offloaded rules are now set and refuse
inline mode changes if this isn't zero.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code to deal with add/del TC rules to have handler per NIC/E-switch
offloading use case, and push the latter into the e-switch code. This provides
better separation and is to be used in down-stream patch for applying a fix.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch cases for the rate limit set and query commands were
missing, which could get us wrong under fw error or driver reset
flow, fix that.
Fixes: 1466cc5b23 ('net/mlx5: Rate limit tables support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi
* fix a user reported warning in DQA
mwifiex
* fix a potential double free
* fix lost early debug logs
* fix init wakeup warning message from device framework
* add Ganapathi and Xinming as maintainers
ath10k
* fix regression with QCA6174 during resume and firmware crash
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY0S5DAAoJEG4XJFUm622bYoYH/AxiLF0UleRgeHeQAQd4d1d0
QsISkT+Xm1p43P3GQ9qoKocHd0S0GvWCqzHC2HAeDmLFAUf5gfo3hhGqEvTVEvCo
eUiNjIJyezNcvo9JJwmB/P8O2nVJH9tUtSISwKfnvG/XT4olSJfE+vPi0edOXG4s
IvDdO8AiuoZHoP11utNtMsg4vnA1uvy75ti20fe69PX5g9G/+gcDBkFHh/IpcfML
GSRZaZjKxsaWKnSUimPJlJsvsJE+mcsXD2rPImEiinQbR2yTfkAcmdxaQR9fkVSP
1FdT4MvWoxrK4sUaPSn3ZO/eVzNeDXi9bQPGQwBpq6rUZp7r9OPkdRqGWbi/hW8=
=zzBr
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.11
iwlwifi
* fix a user reported warning in DQA
mwifiex
* fix a potential double free
* fix lost early debug logs
* fix init wakeup warning message from device framework
* add Ganapathi and Xinming as maintainers
ath10k
* fix regression with QCA6174 during resume and firmware crash
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address() which
looks up the MAC address using the 3 typical property names.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Coverity scan errors by not dereferencing lio->glists_dma_base pointer
if it's NULL.
See http://marc.info/?l=linux-netdev&m=149002294305614&w=2
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: VSR Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VRF driver allows users to implement device based features for an
entire domain. For example, a qdisc or netfilter rules can be attached
to a VRF device or tcpdump can be used to view packets for all devices
in the L3 domain.
The device-based features come with a performance penalty, most
notably in the Tx path. The VRF driver uses the l3mdev_l3_out hook
to switch the dst on an skb to its private dst. This allows the skb
to traverse the xmit stack with the device set to the VRF device
which in turn enables the netfilter and qdisc features. The VRF
driver then performs the FIB lookup again and reinserts the packet.
This patch avoids the redirect for IPv6 packets if a qdisc has not
been attached to a VRF device which is the default config. In this
case the netfilter hooks and network taps are directly traversed in
the l3mdev_l3_out handler. If a qdisc is attached to a VRF device,
then the redirect using the vrf dst is done.
Additional overhead is removed by only checking packet taps if a
socket is open on the device (vrf_dev->ptype_all list is not empty).
Packet sockets bound to any device will still get a copy of the
packet via the real ingress or egress interface.
The end result of this change is a decrease in the overhead of VRF
for the default, baseline case (ie., no netfilter rules, no packet
sockets, no qdisc) from a +3% improvement for UDP which has a lookup
per packet (VRF being better than no l3mdev) to ~2% loss for TCP_CRR
which connects a socket for each request-response.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VRF driver allows users to implement device based features for an
entire domain. For example, a qdisc or netfilter rules can be attached
to a VRF device or tcpdump can be used to view packets for all devices
in the L3 domain.
The device-based features come with a performance penalty, most
notably in the Tx path. The VRF driver uses the l3mdev_l3_out hook
to switch the dst on an skb to its private dst. This allows the skb
to traverse the xmit stack with the device set to the VRF device
which in turn enables the netfilter and qdisc features. The VRF
driver then performs the FIB lookup again and reinserts the packet.
This patch avoids the redirect for IPv4 packets if a qdisc has not
been attached to a VRF device which is the default config. In this
case the netfilter hooks and network taps are directly traversed in
the l3mdev_l3_out handler. If a qdisc is attached to a VRF device,
then the redirect using the vrf dst is done.
Additional overhead is removed by only checking packet taps if a
socket is open on the device (vrf_dev->ptype_all list is not empty).
Packet sockets bound to any device will still get a copy of the
packet via the real ingress or egress interface.
The end result of this change is a decrease in the overhead of VRF
for the default, baseline case (ie., no netfilter rules, no packet
sockets, no qdisc) to ~3% for UDP which has a lookup per packet and
< 1% overhead for connected sockets that leverage early demux and
avoid FIB lookups.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arguments packets and bytes to call mlxsw_sp_acl_rule_get_stats are
in the wrong order. Fix this by swapping them.
Detected by CoverityScan, CID#1419705 ("Arguments in wrong order")
Fixes: 7c1b8eb175 ("mlxsw: spectrum: Add support for TC flower offload statistics")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With posix timers having become optional, we get a build error with
the cpts time sync option of the CPSW driver:
drivers/net/ethernet/ti/cpts.c: In function 'cpts_find_ts':
drivers/net/ethernet/ti/cpts.c:291:23: error: implicit declaration of function 'ptp_classify_raw';did you mean 'ptp_classifier_init'? [-Werror=implicit-function-declaration]
This adds a hard dependency on PTP_CLOCK to avoid the problem, as
building it without PTP support makes no sense anyway.
Fixes: baa73d9e47 ("posix-timers: Make them configurable")
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dependency is reversed: cpsw and netcp call into cpts,
but cpts depends on the other two in Kconfig. This can lead
to cpts being a loadable module and its callers built-in:
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_remove':
cpsw.c:(.text.cpsw_remove+0xd0): undefined reference to `cpts_release'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_rx_handler':
cpsw.c:(.text.cpsw_rx_handler+0x2dc): undefined reference to `cpts_rx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_tx_handler':
cpsw.c:(.text.cpsw_tx_handler+0x7c): undefined reference to `cpts_tx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_ndo_stop':
As a workaround, I'm introducing another Kconfig symbol to
control the compilation of cpts, while making the actual
module controlled by a silent symbol that is =y when necessary.
Fixes: 6246168b4a ("net: ethernet: ti: netcp: add support of cpts")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are using the smallest padding boundary (8 bytes), which isn't
smaller than the Memory Controller Read/Write Size
We get best performance in 100G when the Packing Boundary is a multiple
of the Maximum Payload Size. Its related to inefficient chopping of DMA
packets by PCIe, that causes more overhead on bus. So driver is helping
by making the starting address alignment to be MPS size.
We will try to determine PCIE MaxPayloadSize capabiltiy and set
IngPackBoundary based on this value. If cache line size is greater than
MPS or determinig MPS fails, we will use cache line size to determine
IngPackBoundary(as before).
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building the driver as a module, we get a warning about the
lack of a license:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/synopsys/dwc-xlgmac.o
see include/linux/module.h for more information
Curiously the text in the .c files only mentions GPLv2+, while the license
tag in the PCI driver contains both GPL and BSD. I picked the license text
as the more definite reference here and put a GPL tag in there.
Fixes: 65e0ace2c5 ("net: dwc-xlgmac: Initial driver for DesignWare Enterprise Ethernet")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this header, we can run into a build error:
drivers/net/ethernet/synopsys/dwc-xlgmac-hw.c: In function 'xlgmac_config_queue_mapping':
drivers/net/ethernet/synopsys/dwc-xlgmac-hw.c:1548:36: error: 'IEEE_8021QAZ_MAX_TCS' undeclared (first use in this function)
prio_queues = min_t(unsigned int, IEEE_8021QAZ_MAX_TCS,
Fixes: 65e0ace2c5 ("net: dwc-xlgmac: Initial driver for DesignWare Enterprise Ethernet")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jie Deng <jiedeng@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
revert commit a59e6d8152 ("r8152: correct the rx early size") and
fix the rx early size as
(rx buffer size - rx packet size - rx desc size - alignment) / 4
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the received maximum size (RMS) according to the mtu size. It is
unnecessary to receive a packet which is more than the size we could
transmit. Besides, this could let the rx buffer be used effectively.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-03-21
This series contains updates to e1000, e1000e, igb, igbvf and ixgb.
This finishes up the work Philippe Reynes did to update the Intel drivers
to the new API for ethtool (get|set)_link_ksettings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This gets qmicli working with the MDM6600 modem.
Cc: Bjørn Mork <bjorn@mork.no>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link information exists only on the leading hwfn,
but some of its derivatives [e.g., min/max rate] need to
be configured for each hwfn.
When re-basing the VF link view, use the leading hwfn
information as basis for all existing hwfns to allow
said configurations to stick.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Malicious VF existance should be interesting enough for the
hyperuser. Change the PF indication that one of its child VF
became malicious to appear by default.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF<->VF interface allows for the VF to request
multiple queues closure via a single message, but this has
never been used by any official driver.
We now deprecate this option, forcing each queue close
to arrive via a different command; This would be required
for future TLVs that are going to extend the queue TLVs with
additional information on a per-queue basis.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF needs to validate the status of VF queues before asking firmware
to configure anything for them, but that validation is done in various
different forms - sometimes inadequate.
Add auxillary functions that can be used for testing of the queue
state and convert the various flows to use those instead of current
existing flows; Also, add missing validations where needed.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When starting the VF's vport, the PF would first configure
the status blocks of the VF and then reset them.
That would cause some of the configured information to be lost -
specifically it would mean that all the VFs queues would use
the Rx coalescing state-machine of the status block.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PF responds to the VF requests it also cleans the HW-channel
indication in firmware to allow further VF messages to arrive,
but the order currently applied is wrong -
The PF is copying by DMAE the response the VF is polling on for
completion, and only afterwards sets the HW-channel to ready state.
This creates a race condition where the VF would be able to send
an additional message to the PF before the channel would get ready
again, causing the firmware to consider the VF as malicious.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF is considered malicious, driver handling of the VF
FLR flow would clean said indication - but not if the FLR is
part of an sriov-disable flow.
That leads to further issues, as PF wouldn't re-enable the
previously malicious VF when sriov is re-enabled.
No reason for that - simply clean malicious indications in
the sriov-disable flow as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs are currently logging errors when communicating
with their PFs in a too-low verbosity that wouldn't
be shown by default. As timeouts and failed commands
are crucial for VF operability, make them appear by
default.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VRF driver takes a reference to the inet6_dev on the VRF device for
its rt6_local dst when handling local traffic through the VRF device as
a loopback. When the device is deleted the driver does a put on the idev
but does not reset rt6i_idev in the rt6_info struct. When the dst is
destroyed, dst_destroy calls ip6_dst_destroy which does a second put for
what is essentially the same reference causing it to be prematurely freed.
Reset rt6i_idev after the put in the vrf driver.
Fixes: b4869aa2f8 ("net: vrf: ipv6 support for local traffic to
local addresses")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change to support host<->firmware command return value.
Fix for vf mac addr state command.
1. Added support for firmware commands to return a value:
- previously, the returned code overlapped with host codes, thus
commands were only returning 0 (success) or -1 (interpreted as
timeout)
- per 'response_manager.h', the error codes are split into two fields
(major/minor) now, firmware commands are grouped into their own
'major' group, separate from the host's 'major' group, which allow f/w
commands to return any 16-bit value
2. The command to set vf mac addr was logging a success message even if
command failed. Now command uses a callback function to log the status
message.
3. The command to set vf mac addr was not logging a message when set via
the host 'ip' command. Now, the callback function will log an
appropriate message.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When closing the ibmvnic device we need to release the resources used
in communicating to the virtual I/O server. These need to be
re-negotiated with the server at open time.
This patch moves the releasing of resources a separate routine
and updates the open and close handlers to release all resources at
close and re-negotiate and allocate these resources at open.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intialization of the ibmvnic driver with respect to the virtual
server it connects to should be moved to its own routine. This will
alolow the driver to initiate this process from places outside of
the drivers probe routine.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code that handles login and renegotiation of ibmvnic
capabilities to its own routine.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VNIC server expects LINK_STATE_UP to be sent within 30s of the login. If we
exceed the timeout, VNIC server will attempt to fail over. Since time
between probe and open of the device is indeterminate, move login and queue
negotiation into ibmvnic open so we can guarantee that login and sending
LINK_STATE_UP occur within the 30s window.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function gem_begin_auto_negotiation dereference
the pointer ep before testing if it's null. This
patch add a check on ep before dereferencing it.
Fixes: 92552fdda5 ("net: sun: sungem: use new api
ethtool_{get|set}_link_ksettings")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We could allocate less memory than intended because we do:
bnad->regdata = kzalloc(len << 2, GFP_KERNEL);
The shift can overflow leading to a crash. This is debugfs code so the
impact is very small.
Fixes: 7afc5dbde0 ("bna: Add debugfs interface.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Rasesh Mody <rasesh.mody@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add timeout error message in lio_process_ordered_list(). Add host failure
status in existing error message in if_cfg_callback().
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove code duplicated in PF and VF; define that code once only in a common
header file included by PF and VF.
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a Dell branded Sierra Wireless EM7455. It is operating in
MBIM mode by default, but can be configured to provide two QMI/RMNET
functions.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the configuration of RX queues' routing.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the configuration of RX and TX queues' priority.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates 2 new structures (stmmac_tx_queue and stmmac_rx_queue)
in include/linux/stmmac.h, enabling that each RX and TX queue has its
own buffers and data.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ether_addr_copy() instead of memcpy() to set netdev->dev_addr (which
is 2-byte aligned).
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the default case for matchall offload with what's there
for flower.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the struct representing router interface "mlxsw_sp_rif"
is reffered as "r" in various places in the driver. Furthermore it
contains a member which specify the index which is called "rif".
This patch change "r" to "rif" and "rif" to "rif_index".
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check hw version first in probe(). Do nothing if the driver doesn't
support the chip.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function usbnet_{get|set}_settings is no longer used,
so we remove it.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: poma <poma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We add the new api {get|set}_link_ksettings to this driver.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool API {get|set}_settings is deprecated.
We move this driver to new API {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API {get|set}_settings is deprecated.
We move this driver to new API {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API {get|set}_settings is deprecated.
We move this driver to new API {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API {get|set}_settings is deprecated.
We move this driver to new API {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added missing logic in tun driver, which prevents apps to set
offloads using tun ioctl, if offloads were previously disabled via ethtool
Signed-off-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__bcmgenet_tx_reclaim() is currently summing TX bytes/packets in a way
that is not SMP friendly, mutliples CPUs could run
__bcmgenet_tx_reclaim() independently and still update stats->tx_bytes
and stats->tx_packets, cloberring the other CPUs statistics.
Fix this by tracking per RX and TX rings the number of bytes, packets,
dropped and errors statistics, and provide a bcmgenet_get_stats()
function which aggregates everything and returns a consistent output.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool API {get|set}_settings is deprecated.
We move this driver to new API {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following checkpatch.pl recommendations (which include
replacing with <linux/io.h> the <asm/io.h>, since linux/io.h includes
it).
Signed-off-by: Ezequiel Lara Gomez <ezegomez@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables developing code that uses SOF_TIMESTAMPING_TX_SOFTWARE
by using localhost addresses (without needing to send packets outside),
as well as enabling unit and functional testing of TX timestamping code
without needing hardware support or network access.
It also fulfills the expectation of software network devices supporting
software-based timestamping.
Tested on qemu using txtimestamping.c from the kernel selftests, and
ethtool -T.
Signed-off-by: Ezequiel Lara Gomez <ezegomez@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list rx_done would be initialized when the linking on occurs.
Therefore, if a napi is scheduled without any linking on before,
the following kernel panic would happen.
BUG: unable to handle kernel NULL pointer dereference at 000000000000008
IP: [<ffffffffc085efde>] r8152_poll+0xe1e/0x1210 [r8152]
PGD 0
Oops: 0002 [#1] SMP
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-03-20
This series contains updates to i40e and i40evf only.
Philippe Reynes updates i40e and i40evf to use the new ethtool API for
{get|set}_link_ksettings.
Jake provides the remaining patches in the series, starting with a fix
for i40e where the firmware expected the port numbers for the offloaded
UDP tunnels in Little Endian format and we were sending them in Big Endian
format which put the wrong port number to be put in the UDP tunnel list.
Changed the driver to use __be32 values instead of arrays for
(src|dst)_ip. Refactored the exit flow of i40e_add_fdir_ethtool() which
removes the dependency on having a non-zero return value. Fixed a memory
leak by running kfree() and returning immediately when we fail to add
flow director filter. Fixed a potential issue where could update the
filter count without actually succeeding in adding a filter, by moving
the ATR exit check to after we have sent the TCP/IPv4 filter to the ring
successfully. Ensures that the fd_tcp_rule count is reset to 0, before
we reprogram the filters so that we do not end up with a stale count
which does not correctly reflect the number of programmed filters. Added
a check whether we have TCP/IPv4 filters before re-enabling ATR after
flushing and replaying FDIR filters. Added counters for each filter
type in preparation for adding code to properly check the mask value.
Fixed potential issues by explicitly checking the flow type at the
start of i40e_add_fdir_ethtool(). To avoid possible memory leaks,
we now unconditionally delete the old filter, even if it is identical to
the new filter and ensures will always update the filters as expected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous code relied on i40e_match_fdir_input_set to determine when
determining whether to free the old filter. Change this code so that we
simply unconditionally delete the old filter, even if it's identical to
the new filter. This ensures that we don't leak any memory, and that we
always update the filters as expected.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Although we will fail the filter later due to checking flow_type which
will have a bogus invalid type, it is possible future refactoring will
remove this hidden failure case. Avoid a possible issue in the future by
explicitly checking the flow type at the start.
Change-Id: Ia98eb26f7b93ccbe38c7141e8f203ef496fc6598
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for adding code to properly check the mask values, we
will need to know the number of active filters for each type. Add
counters for each filter type. Rename the already existing fd_tcp_rule
to fd_tcp4_filter_cnt to match the style of other names. To avoid style
warnings, avoid assigning multiple parameters at once, and fix up one
other case where we did so previously.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When flushing and replaying FDIR filters, it is possible we would
disable ATR, and then re-enable it even though we should have kept
it disabled due to existing TCP/IPv4 filters. Fix this by checking
whether we have TCP4/IPv4 filters before re-enabling.
Alternatively, we could instead restore ATR and then replay filters,
however, this would cause us to rapidly enable and then disable ATR in
some cases.
Change-ID: I076e4cc1e4409bce7f98f3c213295433a4ff43d8
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Avinash Dayanand <avinash.dayanand@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we're about to reprogram the filters, we need to ensure that the
fd_tcp_rule count is correctly reset to 0. Otherwise, we will keep
a stale count that does not accurately reflect the number of programmed
TCPv4 filters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_fdir_filter_restore re-adds all existing filters, which already
checks when adding a TCPv4 filter to disable ATR. We don't need to make
the check twice, so remove this redundant code.
Change-ID: Ia0b0690e23523915199d601494557def135c9d7f
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move ATR exit check after we have sent the TCP/IPv4 filter to the ring
successfully. This avoids an issue where we potentially update the
filter count without actually succeeding in adding the filter. Now, we
only increment the fd_tcp_rule after we've succeeded. Additionally, we
will re-enable ATR mode only after deletion of the filter is actually
posted to the FDIR ring.
Change-ID: If5c1dea422081cc5e2de65618b01b4c3bf6bd586
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of setting err=true and checking this to determine when to free
the raw_packet near the end of the function, simply kfree and return
immediately. The resulting code is a bit cleaner and has one less
variable. This also resolves a subtle bug in the ipv4 case which could
fail to add the first filter and then never free the memory, resulting
in a small memory leak.
Change-ID: I7583aac033481dc794b4acaa14445059c8930ff1
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Avinash Dayanand <avinash.dayanand@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor the exit flow of the i40e_add_fdir_ethtool function. Move the
input_label to the end of the function, removing the dependency on
having a non-zero return value. Add a comment explaining why it is ok
not to free the fdir data structure, because the structure is now stored
in the fdir_filter_list.
Change-Id: I723342181d59cd0c9f3b31140c37961ba37bb242
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code originally included src_ip and dst_ip with enough space to
support ipv6 filters. However, no actual support for ipv6 filters has
been implemented. Thus, remove the arrays and just use __be32 values.
Should ipv6 support be added in the future, we can replace these with
a union that has sizes for both values.
Change-Id: I1bc04032244a80eb6ebc8a4e6c723a4a665c1dd5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware expects the port numbers for offloaded UDP tunnels in
Little Endian format. We accidentally sent the value in Big Endian
format which obviously will cause the wrong port number to be put into
the UDP tunnels list. This results in VxLAN and Geneve tunnel Rx
offloads being essentially disabled, unless the port number happens to
be identical after byte swapping. Note that i40e_aq_add_udp_tunnel()
will byteswap the parameter from host order into Little Endian so we
don't need worry about passing strictly a __le16 value to the command.
This patch essentially reverts b3f5c7bc88 ("i40e: Fix for extra byte
swap in tunnel setup", 2016-08-24), but in a way that makes the result
much more clear to the reader.
Fixes: b3f5c7bc88 ("i40e: Fix for extra byte swap in tunnel setup", 2016-08-24)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jakub Kicinski