We have so far alwways invalidated VLPIs usinc an INV+SYNC
sequence, but that's pretty wrong for two reasons:
- SYNC only synchronises physical LPIs
- The collection ID that for the associated LPI doesn't match
the redistributor the vPE is associated with
Instead, send an INV+VSYNC for forwarded LPIs, ensuring that
the ITS can properly synchronise the invalidation of VLPIs.
Fixes: 015ec0386a ("irqchip/gic-v3-its: Add VLPI configuration handling")
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191108165805.3071-9-maz@kernel.org
We allocate the collection mapping on device creation, but somehow
free it on the irqdomain free path, which is pretty inconsistent
and has led to bugs in the past.
Move it to the point where we teardown the device, making the
alloc/free symetric.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191108165805.3071-2-maz@kernel.org
Remove the sdm845 SoC specific compatible to make the driver
easily reusable across other SoC's with the same IP block.
This will reduce further churn adding any SoC specific
compatibles unless really needed.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20191108092824.9773-7-rnayak@codeaurora.org
The LS1021A allows inverting the polarity of six interrupt lines
IRQ[0:5] via the scfg_intpcr register, effectively allowing
IRQ_TYPE_LEVEL_LOW and IRQ_TYPE_EDGE_FALLING for those. We just need to
check the type, set the relevant bit in INTPCR accordingly, and fixup
the type argument before calling the GIC's irq_set_type.
In fact, the power-on-reset value of the INTPCR register on the LS1021A
is so that all six lines have their polarity inverted. Hence any
hardware connected to those lines is unusable without this: If the line
is indeed active low, the generic GIC code will reject an irq spec with
IRQ_TYPE_LEVEL_LOW, while if the line is active high, we must obviously
disable the polarity inversion (writing 0 to the relevant bit) before
unmasking the interrupt.
Some other Layerscape SOCs (LS1043A, LS1046A) have a similar feature,
just with a different number of external interrupt lines (and a
different POR value for the INTPCR register). This driver should be
prepared for supporting those by properly filling out the device tree
node. I have the reference manuals for all three boards, but I've only
tested the driver on an LS1021A.
Unfortunately, the Kconfig symbol ARCH_LAYERSCAPE only exists on
arm64, so do as is done for irq-ls-scfg-msi.c: introduce a new symbol
which is set when either ARCH_LAYERSCAPE or SOC_LS1021A is set.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191107122115.6244-3-linux@rasmusvillemoes.dk
On some specific chips like 7211 we need to leave some interrupts
untouched/forwarded to the VPU which is another agent in the system
making use of that interrupt controller hardware (goes to both ARM GIC
and VPU L1 interrupt controller). Make that possible by using the
existing brcm,int-fwd-mask property and take necessary actions to avoid
masking that interrupt as well as not allowing Linux to map them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191024201415.23454-6-f.fainelli@gmail.com
If the 'brcm,irq-can-wake' property is specified, make sure we also
enable the corresponding parent interrupt we are attached to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191024201415.23454-4-f.fainelli@gmail.com
The current L1 controller does not mask any interrupts when dropping
into suspend. This mean we can receive unexpected wake up sources.
Modified the BCM7038 L1 controller to mask the all non-wake interrupts
before dropping into suspend.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191024201415.23454-2-f.fainelli@gmail.com
The its_cmd_block struct can either have u64 or __le64
data in it, so make a anonymous union to remove the
sparse warnings when converting to/from these.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191017112955.15853-1-ben.dooks@codethink.co.uk
Many of the privileged CSRs exist in a supervisor and machine version
that are used very similarly. Provide versions of the CSR names and
fields that map to either the S-mode or M-mode variant depending on
a new CONFIG_RISCV_M_MODE kconfig symbol.
Contains contributions from Damien Le Moal <Damien.LeMoal@wdc.com>
and Paul Walmsley <paul.walmsley@sifive.com>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de> # for drivers/clocksource, drivers/irqchip
[paul.walmsley@sifive.com: updated to apply]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
When the VHE code was reworked, a lot of the vgic stuff was moved around,
but the GICv4 residency code did stay untouched, meaning that we come
in and out of residency on each flush/sync, which is obviously suboptimal.
To address this, let's move things around a bit:
- Residency entry (flush) moves to vcpu_load
- Residency exit (sync) moves to vcpu_put
- On blocking (entry to WFI), we "put"
- On unblocking (exit from WFI), we "load"
Because these can nest (load/block/put/load/unblock/put, for example),
we now have per-VPE tracking of the residency state.
Additionally, vgic_v4_put gains a "need doorbell" parameter, which only
gets set to true when blocking because of a WFI. This allows a finer
control of the doorbell, which now also gets disabled as soon as
it gets signaled.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191027144234.8395-2-maz@kernel.org
- Sifive PLIC: force driver to skip non-relevant contexts
- GICv4: Don't send VMOVP commands to ITSs that don't have
this vPE mapped
-----BEGIN PGP SIGNATURE-----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=9wMN
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull the second lot of irqchip updates for 5.4 from Marc Zyngier:
- Sifive PLIC: force driver to skip non-relevant contexts
- GICv4: Don't send VMOVP commands to ITSs that don't have
this vPE mapped
Modify plic_init() to skip .dts interrupt contexts other
than supervisor external interrupt.
The .dts entry for plic may specify multiple interrupt contexts.
For example, it may assign two entries IRQ_M_EXT and IRQ_S_EXT,
in that order, to the same interrupt controller. This patch
modifies plic_init() to skip the IRQ_M_EXT context since
IRQ_S_EXT is currently the only supported context.
If IRQ_M_EXT is not skipped, plic_init() will report "handler
already present for context" when it comes across the IRQ_S_EXT
context in the next iteration of its loop.
Without this patch, .dts would have to be edited to replace the
value of IRQ_M_EXT with -1 for it to be skipped.
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Walmsley <paul.walmsley@sifive.com> # arch/riscv
Link: https://lkml.kernel.org/r/1571933503-21504-1-git-send-email-alan.mikhak@sifive.com
On a system without Single VMOVP support (say GITS_TYPER.VMOVP == 0),
we will map vPEs only on ITSs that will actually control interrupts
for the given VM. And when moving a vPE, the VMOVP command will be
issued only for those ITSs.
But when issuing VMOVPs we seemed fail to present the exact ITSList
to ITSs who are actually included in the synchronization operation.
The its_list_map we're currently using includes all ITSs in the system,
even though some of them don't have the corresponding vPE mapping at all.
Introduce get_its_list() to get the per-VM its_list_map, to indicate
which ITSs have vPE mappings for the given VM, and use this map as
the expected ITSList when building VMOVP. This is hopefully a performance
gain not to do some synchronization with those unsuspecting ITSs.
And initialize the whole command descriptor to zero at beginning, since
the seq_num and its_list should be RES0 when GITS_TYPER.VMOVP == 1.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1571802386-2680-1-git-send-email-yuzenghui@huawei.com
The GICv3 architecture specification is incredibly misleading when it
comes to PMR and the requirement for a DSB. It turns out that this DSB
is only required if the CPU interface sends an Upstream Control
message to the redistributor in order to update the RD's view of PMR.
This message is only sent when ICC_CTLR_EL1.PMHE is set, which isn't
the case in Linux. It can still be set from EL3, so some special care
is required. But the upshot is that in the (hopefuly large) majority
of the cases, we can drop the DSB altogether.
This relies on a new static key being set if the boot CPU has PMHE
set. The drawback is that this static key has to be exported to
modules.
Cc: Will Deacon <will@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- Add retrigger support to Amazon's al-fic driver
- Add SAM9X60 support to Atmel's AIC5 irqchip
- Fix GICv3 maximum interrupt calculation
- Convert SiFive's PLIC to the fasteoi IRQ flow
-----BEGIN PGP SIGNATURE-----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=AV7P
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- Add retrigger support to Amazon's al-fic driver
- Add SAM9X60 support to Atmel's AIC5 irqchip
- Fix GICv3 maximum interrupt calculation
- Convert SiFive's PLIC to the fasteoi IRQ flow
- boot_mem_map is removed, providing a nice cleanup made possible by the
recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
- pte_special() is now supported for some configurations, allowing among
other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil, mostly
enabled by the inclusion of the new TCU (timer-counter unit) drivers
he's spent a very patient year or so working on. Plus some fixes for
X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
=lWlM
-----END PGP SIGNATURE-----
Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
The SiFive PLIC interrupt controller seems to have all the HW
features to support the fasteoi flow, but the driver seems to be
stuck in a distant past. Bring it into the 21st century.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Palmer Dabbelt <palmer@sifive.com> (QEMU Boot)
Tested-by: Darius Rad <darius@bluespec.com> (on 2 HW PLIC implementations)
Tested-by: Paul Walmsley <paul.walmsley@sifive.com> (HiFive Unleashed)
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/8636gxskmj.wl-maz@kernel.org
As per GIC spec, ITLinesNumber indicates the maximum SPI INTID that
the GIC implementation supports. And the maximum SPI INTID an
implementation might support is 1019 (field value 11111).
max(GICD_TYPER_SPIS(...), 1020) is not what we actually want for
GIC_LINE_NR. Fix it to min(GICD_TYPER_SPIS(...), 1020).
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1568789850-14080-1-git-send-email-yuzenghui@huawei.com
Pull core irq updates from Thomas Gleixner:
"Updates from the irq departement:
- Update the interrupt spreading code so it handles numa node with
different CPU counts properly.
- A large overhaul of the ARM GiCv3 driver to support new PPI and SPI
ranges.
- Conversion of all alloc_fwnode() users to use physical addresses
instead of virtual addresses so the virtual addresses are not
leaked. The physical address is sufficient to identify the
associated interrupt chip.
- Add support for Marvel MMP3, Amlogic Meson SM1 interrupt chips.
- Enforce interrupt threading at compile time if RT is enabled.
- Small updates and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
irqchip/gic-v3-its: Fix LPI release for Multi-MSI devices
irqchip/uniphier-aidet: Use devm_platform_ioremap_resource()
irqdomain: Add the missing assignment of domain->fwnode for named fwnode
irqchip/mmp: Coexist with GIC root IRQ controller
irqchip/mmp: Mask off interrupts from other cores
irqchip/mmp: Add missing chained_irq_{enter,exit}()
irqchip/mmp: Do not use of_address_to_resource() to get mux regs
irqchip/meson-gpio: Add support for meson sm1 SoCs
dt-bindings: interrupt-controller: New binding for the meson sm1 SoCs
genirq/affinity: Remove const qualifier from node_to_cpumask argument
genirq/affinity: Spread vectors on node according to nr_cpu ratio
genirq/affinity: Improve __irq_build_affinity_masks()
irqchip: Remove dev_err() usage after platform_get_irq()
irqchip: Add include guard to irq-partition-percpu.h
irqchip/mmp: Do not call irq_set_default_host() on DT platforms
irqchip/gic-v3-its: Remove the redundant set_bit for lpi_map
irqchip/gic-v3: Add quirks for HIP06/07 invalid GICD_TYPER erratum 161010803
irqchip/gic: Skip DT quirks when evaluating IIDR-based quirks
irqchip/gic-v3: Warn about inconsistent implementations of extended ranges
irqchip/gic-v3: Add EPPI range support
...
When allocating a range of LPIs for a Multi-MSI capable device,
this allocation extended to the closest power of 2.
But on the release path, the interrupts are released one by
one. This results in not releasing the "extra" range, leaking
the its_device. Trying to reprobe the device will then fail.
Fix it by releasing the LPIs the same way we allocate them.
Fixes: 8208d1708b ("irqchip/gic-v3-its: Align PCI Multi-MSI allocation on their size")
Reported-by: Jiaxing Luo <luojiaxing@huawei.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/f5e948aa-e32f-3f74-ae30-31fee06c2a74@huawei.com
When running in M-mode, the S-mode plic handlers are still listed in the
device tree. Ignore them by setting the maximum threshold.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Replace the chain of platform_get_resource() and devm_ioremap_resource()
with devm_platform_ioremap_resource().
This allows to remove the local variable for (struct resource *), and
have one function call less.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20190905034932.12587-1-yamada.masahiro@socionext.com
On MMP3, the GIC can be set as a root IRQ interrupt controller. If the
device tree indicated that GIC is enabled, avoid hooking up
mmp2_handle_irq().
The interrupt muxes are still being used.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20190822092643.593488-10-lkundrak@v3.sk
On mmp3, there's an extra set of ICU registers (ICU2) that handle
interrupts on the extra cores. When masking off interrupts on MP1,
these should be masked as well.
We add a new interrupt controller via device tree to identify when we're
looking at an mmp3 machine via compatible field of "marvell,mmp3-intc".
[lkundrak@v3.sk: Changed "mrvl,mmp3-intc" compatible strings to
"marvell,mmp3-intc". Tidied up the subject line a bit.]
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20190822092643.593488-9-lkundrak@v3.sk
--
Changes since v1:
- Moved mmp3-specific mmp_icu2_base initialization from mmp_init_bases() to
mmp3_of_init() so that we don't have to check for marvell,mmp3-intc
compatibility twice.
- Drop an superfluous call to irq_set_default_host()
arch/arm/mach-mmp/regs-icu.h | 3 +++
drivers/irqchip/irq-mmp.c | 48 ++++++++++++++++++++++++++++++++++++
2 files changed, 51 insertions(+)
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20190822092643.593488-9-lkundrak@v3.sk
The lack of chained_irq_exit() leaves the muxed interrupt masked on MMP3.
For reasons unknown this is not a problem on MMP2.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20190822092643.593488-8-lkundrak@v3.sk
The "regs" property of the "mrvl,mmp2-mux-intc" devices are silly. They
are offsets from intc's base, not addresses on the parent bus. At this
point it probably can't be fixed.
On an OLPC XO-1.75 machine, the muxes are children of the intc, not the
axi bus, and thus of_address_to_resource() won't work. We should treat
the values as mere integers as opposed to bus addresses.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/20190822092643.593488-7-lkundrak@v3.sk
The meson sm1 SoCs uses the same type of GPIO interrupt controller IP
block as the other meson SoCs, A total of 100 pins can be spied on:
- 223:100 undefined (no interrupt)
- 99:97 3 pins on bank GPIOE
- 96:77 20 pins on bank GPIOX
- 76:61 16 pins on bank GPIOA
- 60:53 8 pins on bank GPIOC
- 52:37 16 pins on bank BOOT
- 36:28 9 pins on bank GPIOH
- 27:12 16 pins on bank GPIOZ
- 11:0 12 pins in the AO domain
Mapping is the same as the g12a family but the sm1 controller
allows to trig an irq on both edges of the input signal. This was
not possible with the previous SoCs families
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20190829161635.25067-3-jbrunet@baylibre.com
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Using a default domain on DT platforms is unnecessary, as the firmware
tables describe the full topology, and nothing is implicit.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
[maz: wrote an actual changelog]
Signed-off-by: Marc Zyngier <maz@kernel.org>
We try to find a free LPI region in device's lpi_map and allocate them
(set them to 1) when we want to allocate LPIs for this device. This is
what bitmap_find_free_region() has done for us. The following set_bit
is redundant and a bit confusing (since we only set_bit against the first
allocated LPI idx). Remove it, and make the set_bit explicit by comment.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
It looks like the HIP06/07 SoCs have extra bits in their GICD_TYPER
registers, which confuse the GICv3.1 code (these systems appear to
expose ESPIs while they actually don't).
Detect these systems as early as possible and wipe the fields that
should be RES0 in the register.
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When evaluating potential quirks matched by reads of the IIDR
register, skip the quirk entries that use a "compatible"
property attached to them, as these are DT based.
Signed-off-by: Marc Zyngier <maz@kernel.org>
As is it usual for the GIC, it isn't disallowed to put together a system
that is majorly inconsistent, with a distributor supporting the
extended ranges while some of the CPUs don't.
Kindly tell the user that things are sailing isn't going to be smooth.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Expand the pre-existing PPI support to be able to deal with the
Extended PPI range (EPPI). This includes obtaining the number of PPIs
from each individual redistributor, and compute the minimum set
(just in case someone builds something really clever...).
Signed-off-by: Marc Zyngier <maz@kernel.org>
Again, PPIs are becoming a variable set. Let's hack the PPI partition
code to make the top-level array dynamically allocated.
Signed-off-by: Marc Zyngier <maz@kernel.org>
As we're about to have a variable number of PPIs, let's make the
allocation of the NMI refcounts dynamic. Also apply some minor
cleanups (moving things around).
Signed-off-by: Marc Zyngier <maz@kernel.org>
GICv3.1 allows up to 80 PPIs (16 legaci PPIs and 64 Extended PPIs),
meaning we can't just leave the old 16 hardcoded everywhere.
We also need to add the infrastructure to discover the number of PPIs
on a per redistributor basis, although we still pretend there is only
16 of them for now.
No functional change.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Add the required support for the ESPI range, which behave exactly like
the SPIs of old, only with new funky INTIDs.
Signed-off-by: Marc Zyngier <maz@kernel.org>
In the beginning, life was simple. The GIC driver mostly cared about
PPIs, SPIs and LPIs, all with nicely layed out ranges.
We're about to change all that, with new ranges such as EPPI and ESPI
interleaved in the middle of the no-irq-land between the "special IDs"
and the LPI range. Boo.
In order to make our life less hellish, let's introduce a set of primitives
that will allow ranges to be identified easily and offsets to be remapped.
So far, there is no functionnal change.
Signed-off-by: Marc Zyngier <maz@kernel.org>
gic_configure_irq is currently passed the (re)distributor address,
to which it applies an a fixed offset to get to the configuration
registers. This offset is constant across all GICs, or rather it was
until to v3.1...
An easy way out is for the individual drivers to pass the base
address of the configuration register for the considered interrupt.
At the same time, move part of the error handling back to the
individual drivers, as things are about to change on that front.
Signed-off-by: Marc Zyngier <maz@kernel.org>
While do COMPILE_TEST building, if GENERIC_IRQ_CHIP is
not selected, it fails:
drivers/irqchip/irq-ingenic-tcu.o: In function `ingenic_tcu_intc_cascade':
irq-ingenic-tcu.c:(.text+0x13f): undefined reference to `irq_get_domain_generic_chip'
drivers/irqchip/irq-ingenic-tcu.o: In function `ingenic_tcu_irq_init':
irq-ingenic-tcu.c:(.init.text+0x97): undefined reference to `irq_generic_chip_ops'
irq-ingenic-tcu.c:(.init.text+0xdd): undefined reference to `__irq_alloc_domain_generic_chips'
irq-ingenic-tcu.c:(.init.text+0x10b): undefined reference to `irq_get_domain_generic_chip'
select GENERIC_IRQ_CHIP to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 9536eba03e ("irqchip: Add irq-ingenic-tcu driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: <jason@lakedaemon.net>
Cc: <maz@kernel.org>
Cc: <paul@crapouillou.net>
Cc: <malat@debian.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: <linux-mips@vger.kernel.org>
Cc: <linux-clk@vger.kernel.org>
This driver handles the interrupt controller built in the Timer/Counter
Unit (TCU) of the JZ47xx SoCs from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: od@zcrc.me
Do not expose the base VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Do not expose the frame's VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Do not expose the distributor's VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Do not expose the ITS' VA (it appears in debugfs). Instead, record
the PA, which at least can be used to precisely identify the associated
irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Do not expose the distributor's VA (it appears in debugfs). Instead,
record the PA, which at least can be used to precisely identify
the associated irqchip and domain.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
- Fix a couple of UAF on error paths (RZA1, GICv3 ITS)
- Fix iMX GPCv2 trigger setting
- Add missing of_node_put on error path in MBIGEN
- Add another bunch of /* fall-through */ to silence warnings
-----BEGIN PGP SIGNATURE-----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=oXHS
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
A small bunch of fixes from the irqchip department:
- Fix a couple of UAF on error paths (RZA1, GICv3 ITS)
- Fix iMX GPCv2 trigger setting
- Add missing of_node_put on error path in MBIGEN
- Add another bunch of /* fall-through */ to silence warnings
The gic_node is still being used in the rza1_irqc_parse_map() call
after the of_node_put() call, which may result in use-after-free.
Fixes: a644ccb819 ("irqchip: Add Renesas RZ/A1 Interrupt Controller driver")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The GPCv2 is a stacked IRQ controller below the ARM GIC. It doesn't
care about the IRQ type itself, but needs to forward the type to the
parent IRQ controller, so this one can be configured correctly.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Each iteration of for_each_child_of_node puts the previous node, but
in the case of a return from the middle of the loop, there is no put,
thus causing a memory leak. Add an of_node_put before the return in
three places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
In its_vpe_init, when its_alloc_vpe_table fails, we should free
vpt_page allocated just before, instead of vpe->vpt_page.
Let's fix it.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Nianyao Tang <tangnianyao@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When fall-through warnings was enabled by default the following warning
was starting to show up:
In file included from ../arch/arm64/include/asm/cputype.h:132,
from ../arch/arm64/include/asm/cache.h:8,
from ../include/linux/cache.h:6,
from ../include/linux/printk.h:9,
from ../include/linux/kernel.h:15,
from ../include/linux/list.h:9,
from ../include/linux/kobject.h:19,
from ../include/linux/of.h:17,
from ../include/linux/irqdomain.h:35,
from ../include/linux/acpi.h:13,
from ../drivers/irqchip/irq-gic-v3.c:9:
../drivers/irqchip/irq-gic-v3.c: In function ‘gic_cpu_sys_reg_init’:
../arch/arm64/include/asm/sysreg.h:853:2: warning: this statement may fall
through [-Wimplicit-fallthrough=]
asm volatile(__msr_s(r, "%x0") : : "rZ" (__val)); \
^~~
../arch/arm64/include/asm/arch_gicv3.h:20:29: note: in expansion of macro ‘write_sysreg_s’
#define write_gicreg(v, r) write_sysreg_s(v, SYS_ ## r)
^~~~~~~~~~~~~~
../drivers/irqchip/irq-gic-v3.c:773:4: note: in expansion of macro ‘write_gicreg’
write_gicreg(0, ICC_AP0R2_EL1);
^~~~~~~~~~~~
../drivers/irqchip/irq-gic-v3.c:774:3: note: here
case 6:
^~~~
Rework so that the compiler doesn't warn about fall-through.
Fixes: d93512ef0f0e ("Makefile: Globally enable fall-through warning")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The gic_node is still being used in the rza1_irqc_parse_map() call
after the of_node_put() call, which may result in use-after-free.
Fixes: a644ccb819 ("irqchip: Add Renesas RZ/A1 Interrupt Controller driver")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lkml.kernel.org/r/1562566745-7447-3-git-send-email-wen.yang99@zte.com.cn
Pull irq updates from Thomas Gleixner:
"The irq departement provides the usual mixed bag:
Core:
- Further improvements to the irq timings code which aims to predict
the next interrupt for power state selection to achieve better
latency/power balance
- Add interrupt statistics to the core NMI handlers
- The usual small fixes and cleanups
Drivers:
- Support for Renesas RZ/A1, Annapurna Labs FIC, Meson-G12A SoC and
Amazon Gravition AMR/GIC interrupt controllers.
- Rework of the Renesas INTC controller driver
- ACPI support for Socionext SoCs
- Enhancements to the CSKY interrupt controller
- The usual small fixes and cleanups"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
irq/irqdomain: Fix comment typo
genirq: Update irq stats from NMI handlers
irqchip/gic-pm: Remove PM_CLK dependency
irqchip/al-fic: Introduce Amazon's Annapurna Labs Fabric Interrupt Controller Driver
dt-bindings: interrupt-controller: Add Amazon's Annapurna Labs FIC
softirq: Use __this_cpu_write() in takeover_tasklets()
irqchip/mbigen: Stop printing kernel addresses
irqchip/gic: Add dependency for ARM_GIC_MAX_NR
genirq/affinity: Remove unused argument from [__]irq_build_affinity_masks()
genirq/timings: Add selftest for next event computation
genirq/timings: Add selftest for irqs circular buffer
genirq/timings: Add selftest for circular array
genirq/timings: Encapsulate storing function
genirq/timings: Encapsulate timings push
genirq/timings: Optimize the period detection speed
genirq/timings: Fix timings buffer inspection
genirq/timings: Fix next event index function
irqchip/qcom: Use struct_size() in devm_kzalloc()
irqchip/irq-csky-mpintc: Remove unnecessary loop in interrupt handler
dt-bindings: interrupt-controller: Update csky mpintc
...
- arm64 support for syscall emulation via PTRACE_SYSEMU{,_SINGLESTEP}
- Wire up VM_FLUSH_RESET_PERMS for arm64, allowing the core code to
manage the permissions of executable vmalloc regions more strictly
- Slight performance improvement by keeping softirqs enabled while
touching the FPSIMD/SVE state (kernel_neon_begin/end)
- Expose a couple of ARMv8.5 features to user (HWCAP): CondM (new XAFLAG
and AXFLAG instructions for floating point comparison flags
manipulation) and FRINT (rounding floating point numbers to integers)
- Re-instate ARM64_PSEUDO_NMI support which was previously marked as
BROKEN due to some bugs (now fixed)
- Improve parking of stopped CPUs and implement an arm64-specific
panic_smp_self_stop() to avoid warning on not being able to stop
secondary CPUs during panic
- perf: enable the ARM Statistical Profiling Extensions (SPE) on ACPI
platforms
- perf: DDR performance monitor support for iMX8QXP
- cache_line_size() can now be set from DT or ACPI/PPTT if provided to
cope with a system cache info not exposed via the CPUID registers
- Avoid warning on hardware cache line size greater than
ARCH_DMA_MINALIGN if the system is fully coherent
- arm64 do_page_fault() and hugetlb cleanups
- Refactor set_pte_at() to avoid redundant READ_ONCE(*ptep)
- Ignore ACPI 5.1 FADTs reported as 5.0 (infer from the 'arm_boot_flags'
introduced in 5.1)
- CONFIG_RANDOMIZE_BASE now enabled in defconfig
- Allow the selection of ARM64_MODULE_PLTS, currently only done via
RANDOMIZE_BASE (and an erratum workaround), allowing modules to spill
over into the vmalloc area
- Make ZONE_DMA32 configurable
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE5RElWfyWxS+3PLO2a9axLQDIXvEFAl0eHqcACgkQa9axLQDI
XvFyNA/+L+bnkz8m3ncydlqqfXomQn4eJJVQ8Uksb0knJz+1+3CUxxbO4ry4jXZN
fMkbggYrDPRKpDbsUl0lsRipj7jW9bqan+N37c3SWqCkgb6HqDaHViwxdx6Ec/Uk
gHudozDSPh/8c7hxGcSyt/CFyuW6b+8eYIQU5rtIgz8aVY2BypBvS/7YtYCbIkx0
w4CFleRTK1zXD5mJQhrc6jyDx659sVkrAvdhf6YIymOY8nBTv40vwdNo3beJMYp8
Po/+0Ixu+VkHUNtmYYZQgP/AGH96xiTcRnUqd172JdtRPpCLqnLqwFokXeVIlUKT
KZFMDPzK+756Ayn4z4huEePPAOGlHbJje8JVNnFyreKhVVcCotW7YPY/oJR10bnc
eo7yD+DxABTn+93G2yP436bNVa8qO1UqjOBfInWBtnNFJfANIkZweij/MQ6MjaTA
o7KtviHnZFClefMPoiI7HDzwL8XSmsBDbeQ04s2Wxku1Y2xUHLx4iLmadwLQ1ZPb
lZMTZP3N/T1554MoURVA1afCjAwiqU3bt1xDUGjbBVjLfSPBAn/25IacsG9Li9AF
7Rp1M9VhrfLftjFFkB2HwpbhRASOxaOSx+EI3kzEfCtM2O9I1WHgP3rvCdc3l0HU
tbK0/IggQicNgz7GSZ8xDlWPwwSadXYGLys+xlMZEYd3pDIOiFc=
=0TDT
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- arm64 support for syscall emulation via PTRACE_SYSEMU{,_SINGLESTEP}
- Wire up VM_FLUSH_RESET_PERMS for arm64, allowing the core code to
manage the permissions of executable vmalloc regions more strictly
- Slight performance improvement by keeping softirqs enabled while
touching the FPSIMD/SVE state (kernel_neon_begin/end)
- Expose a couple of ARMv8.5 features to user (HWCAP): CondM (new
XAFLAG and AXFLAG instructions for floating point comparison flags
manipulation) and FRINT (rounding floating point numbers to integers)
- Re-instate ARM64_PSEUDO_NMI support which was previously marked as
BROKEN due to some bugs (now fixed)
- Improve parking of stopped CPUs and implement an arm64-specific
panic_smp_self_stop() to avoid warning on not being able to stop
secondary CPUs during panic
- perf: enable the ARM Statistical Profiling Extensions (SPE) on ACPI
platforms
- perf: DDR performance monitor support for iMX8QXP
- cache_line_size() can now be set from DT or ACPI/PPTT if provided to
cope with a system cache info not exposed via the CPUID registers
- Avoid warning on hardware cache line size greater than
ARCH_DMA_MINALIGN if the system is fully coherent
- arm64 do_page_fault() and hugetlb cleanups
- Refactor set_pte_at() to avoid redundant READ_ONCE(*ptep)
- Ignore ACPI 5.1 FADTs reported as 5.0 (infer from the
'arm_boot_flags' introduced in 5.1)
- CONFIG_RANDOMIZE_BASE now enabled in defconfig
- Allow the selection of ARM64_MODULE_PLTS, currently only done via
RANDOMIZE_BASE (and an erratum workaround), allowing modules to spill
over into the vmalloc area
- Make ZONE_DMA32 configurable
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (54 commits)
perf: arm_spe: Enable ACPI/Platform automatic module loading
arm_pmu: acpi: spe: Add initial MADT/SPE probing
ACPI/PPTT: Add function to return ACPI 6.3 Identical tokens
ACPI/PPTT: Modify node flag detection to find last IDENTICAL
x86/entry: Simplify _TIF_SYSCALL_EMU handling
arm64: rename dump_instr as dump_kernel_instr
arm64/mm: Drop [PTE|PMD]_TYPE_FAULT
arm64: Implement panic_smp_self_stop()
arm64: Improve parking of stopped CPUs
arm64: Expose FRINT capabilities to userspace
arm64: Expose ARMv8.5 CondM capability to userspace
arm64: defconfig: enable CONFIG_RANDOMIZE_BASE
arm64: ARM64_MODULES_PLTS must depend on MODULES
arm64: bpf: do not allocate executable memory
arm64/kprobes: set VM_FLUSH_RESET_PERMS on kprobe instruction pages
arm64/mm: wire up CONFIG_ARCH_HAS_SET_DIRECT_MAP
arm64: module: create module allocations without exec permissions
arm64: Allow user selection of ARM64_MODULE_PLTS
acpi/arm64: ignore 5.1 FADTs that are reported as 5.0
arm64: Allow selecting Pseudo-NMI again
...
gic-pm driver does not use pm-clk interface now and hence the dependency
is removed from Kconfig.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Amazon's Annapurna Labs Fabric Interrupt Controller has 32 inputs.
A FIC (Fabric Interrupt Controller) may be cascaded into another FIC or
directly to the main CPU Interrupt Controller (e.g. GIC).
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull irq fixes from Ingo Molnar:
"Diverse irqchip driver fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Fix command queue pointer comparison bug
irqchip/mips-gic: Use the correct local interrupt map registers
irqchip/ti-sci-inta: Fix kernel crash if irq_create_fwspec_mapping fail
irqchip/irq-csky-mpintc: Support auto irq deliver to all cpus
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
In the presence of any form of instrumentation, nmi_enter() should be
done before calling any traceable code and any instrumentation code.
Currently, nmi_enter() is done in handle_domain_nmi(), which is much
too late as instrumentation code might get called before. Move the
nmi_enter/exit() calls to the arch IRQ vector handler.
On arm64, it is not possible to know if the IRQ vector handler was
called because of an NMI before acknowledging the interrupt. However, It
is possible to know whether normal interrupts could be taken in the
interrupted context (i.e. if taking an NMI in that context could
introduce a potential race condition).
When interrupting a context with IRQs disabled, call nmi_enter() as soon
as possible. In contexts with IRQs enabled, defer this to the interrupt
controller, which is in a better position to know if an interrupt taken
is an NMI.
Fixes: bc3c03ccb4 ("arm64: Enable the support of pseudo-NMIs")
Cc: <stable@vger.kernel.org> # 5.1.x-
Cc: Will Deacon <will.deacon@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses the full gnu general public license is included in this
distribution in the file called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081202.258730266@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kbuild complains about ixp4xx_irq_setup not being __init
itself in some configurations:
WARNING: vmlinux.o(.text+0x85bae4): Section mismatch in reference from the function ixp4xx_irq_setup() to the function .init.text:set_handle_irq()
The function ixp4xx_irq_setup() references
the function __init set_handle_irq().
This is often because ixp4xx_irq_setup lacks a __init
annotation or the annotation of set_handle_irq is wrong.
I suspect it normally gets inlined, so we get no such warning,
but clang makes this obvious when the function is left out
of line.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
After commit ad67b74d24 ("printk: hash addresses printed with %p"),
it will print "____ptrval____" instead of actual addresses when mbigen
create domain fails,
Hisilicon MBIGEN-V2 HISI0152:00: Failed to create mbi-gen@(____ptrval____) irqdomain
Hisilicon MBIGEN-V2: probe of HISI0152:00 failed with error -12
dev_xxx() helper contains the device info, HISI0152:00, which stands for
mbigen ACPI HID and its UID, we can identify the failing probed mbigen,
so just remove the printing "mgn_chip->base", and also add missing "\n".
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
CONFIG_ARM_GIC_MAX_NR is enabled by default.
It is redundant in x86 and IA-64 where is
without GIC.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = devm_kzalloc(dev, size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
Notice that, in this case, variable alloc_sz is not necessary, hence it
is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
csky_mpintc_handler()
->handle_domain_irq()
->irq_exit()
->invoke_softirq()
->__do_softirq()
->local_irq_enable()
If new interrupt coming, it'll get into interrupt trap before return to
csky_mpintc_handler(). So there is no need loop in csky_mpintc_handler.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Support 4 triger types:
- IRQ_TYPE_LEVEL_HIGH
- IRQ_TYPE_LEVEL_LOW
- IRQ_TYPE_EDGE_RISING
- IRQ_TYPE_EDGE_FALLING
All of above could be set in DeviceTree file and it still compatible
with the old DeviceTree format.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The irq_chip .name field should contain the device's class (not
instance) name, while .parent_device should point to the device itself.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The irq_chip .name field should contain the device's class (not
instance) name, while .parent_device should point to the device itself.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Meson-G12A SoC uses the same GPIO interrupt controller IP block as the
other Meson SoCs, A totle of 100 pins can be spied on, which is the sum of:
- 223:100 undefined (no interrupt)
- 99:97 3 pins on bank GPIOE
- 96:77 20 pins on bank GPIOX
- 76:61 16 pins on bank GPIOA
- 60:53 8 pins on bank GPIOC
- 52:37 16 pins on bank BOOT
- 36:28 9 pins on bank GPIOH
- 27:12 16 pins on bank GPIOZ
- 11:0 12 pins in the AO domain
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Enable compile-testing for all Renesas interrupt controller drivers,
except for RENESAS_H8300H_INTC. The latter relies on a function
(ctrl_bclr()) that is not available on other architectures.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add support for Amazon Graviton custom variant of GICv2m, where the message
is encoded using the MSI message address, as opposed to standard
GICv2m, where the SPI number is encoded in the MSI message data.
In addition, the Graviton flavor of GICv2m is used along GICv3 (and not
GICv2).
Co-developed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Zeev Zilberman <zeev@amazon.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 136 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.384967451@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we run several VMs with PCI passthrough and GICv4 enabled, not
pinning vCPUs, we will occasionally see below warnings in dmesg:
ITS queue timeout (65440 65504 480)
ITS cmd its_build_vmovp_cmd failed
The reason for the above issue is that in BUILD_SINGLE_CMD_FUNC:
1. Post the write command.
2. Release the lock.
3. Start to read GITS_CREADR to get the reader pointer.
4. Compare the reader pointer to the target pointer.
5. If reader pointer does not reach the target, sleep 1us and continue
to try.
If we have several processors running the above concurrently, other
CPUs will post write commands while the 1st CPU is waiting the
completion. So we may have below issue:
phase 1:
---rd_idx-----from_idx-----to_idx--0---------
wait 1us:
phase 2:
--------------from_idx-----to_idx--0-rd_idx--
That is the rd_idx may fly ahead of to_idx, and if in case to_idx is
near the wrap point, rd_idx will wrap around. So the below condition
will not be met even after 1s:
if (from_idx < to_idx && rd_idx >= to_idx)
There is another theoretical issue. For a slow and busy ITS, the
initial rd_idx may fall behind from_idx a lot, just as below:
---rd_idx---0--from_idx-----to_idx-----------
This will cause the wait function exit too early.
Actually, it does not make much sense to use from_idx to judge if
to_idx is wrapped, but we need a initial rd_idx when lock is still
acquired, and it can be used to judge whether to_idx is wrapped and
the current rd_idx is wrapped.
We switch to a method of calculating the delta of two adjacent reads
and accumulating it to get the sum, so that we can get the real rd_idx
from the wrapped value even when the queue is almost full.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The MIPS GIC contains a block of registers used to map local interrupts
to a particular CPU interrupt pin. Since these registers are found at a
consecutive range of addresses we access them using an index, via the
(read|write)_gic_v[lo]_map accessor functions. We currently use values
from enum mips_gic_local_interrupt as those indices.
Unfortunately whilst enum mips_gic_local_interrupt provides the correct
offsets for bits in the pending & mask registers, the ordering of the
map registers is subtly different... Compared with the ordering of
pending & mask bits, the map registers move the FDC from the end of the
list to index 3 after the timer interrupt. As a result the performance
counter & software interrupts are therefore at indices 4-6 rather than
indices 3-5.
Notably this causes problems with performance counter interrupts being
incorrectly mapped on some systems, and presumably will also cause
problems for FDC interrupts.
Introduce a function to map from enum mips_gic_local_interrupt to the
index of the corresponding map register, and use it to ensure we access
the map registers for the correct interrupts.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: a0dc5cb5e3 ("irqchip: mips-gic: Simplify gic_local_irq_domain_map()")
Fixes: da61fcf9d6 ("irqchip: mips-gic: Use irq_cpu_online to (un)mask all-VP(E) IRQs")
Reported-and-tested-by: Archer Yan <ayan@wavecomp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
irq_create_fwspec_mapping() can fail, returning 0 as parent_virq. In this
case vint_desc is going to be NULL in ti_sci_inta_alloc_irq() which will
cause NULL pointer dereference.
Also note that irq_create_fwspec_mapping() returns 'unsigned int' so the
check '<=' was wrong.
Use -EINVAL if irq_create_fwspec_mapping() returned with 0.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The csky,mpintc could deliver a external irq to one cpu or all cpus, but
it couldn't deliver a external irq to a group of cpus with cpu_mask. So
we only use auto deliver mode when affinity mask_val is equal to
cpu_present_mask.
There is no limitation for only two cpus in SMP system.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations http www opensource
org licenses gpl license html http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.383790741@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version you should have received a copy of the
gnu general public license along with this program if not write to
the free software foundation inc 675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 35 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.655028468@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify error handling by converting the driver to use managed
allocations and initializations.
Note that platform_get_resource() and ioremap_nocache() are combined in
devm_platform_ioremap_resource().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Nothing really uses irqc_priv.pdev, all users need irqc_priv.pdev->dev.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The probe function uses "&pdev->dev" a lot, hence add a shorthand for
that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is no need to print error messages if kzalloc() or
ioremap_nocache() fail, as the memory allocation core already takes care
of that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The driver never used spinlocks, and thus does not need to include
<linux/spinlock.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a driver for the Renesas RZ/A1 Interrupt Controller.
This supports using up to 8 external interrupts on RZ/A1, with
configurable sense select.
NMI edge select is not yet supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Expose the existing EXIU hierarchical irqchip domain code to permit
the interrupt controller to be used as the irqchip component of a
GPIO controller on ACPI systems, or as the target of ordinary
interrupt resources.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In preparation of adding support for EXIU controller devices described
via ACPI, split the DT init function in a DT specific and a generic part,
where the latter will be reused for ACPI support later.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Based on 1 normalized pattern(s):
licensed under gplv2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 118 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.961286471@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option [no]_[pad]_[ctrl] any later version this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 176 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.652910950@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull IRQ chip updates from Ingo Molnar:
"A late irqchips update:
- New TI INTR/INTA set of drivers
- Rewrite of the stm32mp1-exti driver as a platform driver
- Update the IOMMU MSI mapping API to be RT friendly
- A number of cleanups and other low impact fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
iommu/dma-iommu: Remove iommu_dma_map_msi_msg()
irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg()
irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg()
irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg()
irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg()
iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts
genirq/msi: Add a new field in msi_desc to store an IOMMU cookie
arm64: arch_k3: Enable interrupt controller drivers
irqchip/ti-sci-inta: Add msi domain support
soc: ti: Add MSI domain bus support for Interrupt Aggregator
irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver
dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings
irqchip/ti-sci-intr: Add support for Interrupt Router driver
dt-bindings: irqchip: Introduce TISCI Interrupt router bindings
gpio: thunderx: Use the default parent apis for {request,release}_resources
genirq: Introduce irq_chip_{request,release}_resource_parent() apis
firmware: ti_sci: Add helper apis to manage resources
firmware: ti_sci: Add RM mapping table for am654
firmware: ti_sci: Add support for IRQ management
firmware: ti_sci: Add support for RM core ops
...
SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to multiplatform enabled.
- Cleanups of Davinci
This tag also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release.
-----BEGIN PGP SIGNATURE-----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=pUeO
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
Merge in a few pending fixes from pre-5.1 that didn't get sent in:
MAINTAINERS: update arch/arm/mach-davinci
ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect
ARM: dts: imx6q-logicpd: Reduce inrush current on USBH1
ARM: dts: imx6q-logicpd: Reduce inrush current on start
ARM: dts: imx: Fix the AR803X phy-mode
ARM: dts: sun8i: a33: Reintroduce default pinctrl muxing
arm64: dts: allwinner: a64: Rename hpvcc-supply to cpvdd-supply
ARM: sunxi: fix a leaked reference by adding missing of_node_put
ARM: sunxi: fix a leaked reference by adding missing of_node_put
Signed-off-by: Olof Johansson <olof@lixom.net>
Here is the "big" set of driver core patches for 5.2-rc1
There are a number of ACPI patches in here as well, as Rafael said they
should go through this tree due to the driver core changes they
required. They have all been acked by the ACPI developers.
There are also a number of small subsystem-specific changes in here, due
to some changes to the kobject core code. Those too have all been acked
by the various subsystem maintainers.
As for content, it's pretty boring outside of the ACPI changes:
- spdx cleanups
- kobject documentation updates
- default attribute groups for kobjects
- other minor kobject/driver core fixes
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNHDbw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynDAgCfbb4LBR6I50wFXb8JM/R6cAS7qrsAn1unshKV
8XCYcif2RxjtdJWXbjdm
=/rLh
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core/kobject updates from Greg KH:
"Here is the "big" set of driver core patches for 5.2-rc1
There are a number of ACPI patches in here as well, as Rafael said
they should go through this tree due to the driver core changes they
required. They have all been acked by the ACPI developers.
There are also a number of small subsystem-specific changes in here,
due to some changes to the kobject core code. Those too have all been
acked by the various subsystem maintainers.
As for content, it's pretty boring outside of the ACPI changes:
- spdx cleanups
- kobject documentation updates
- default attribute groups for kobjects
- other minor kobject/driver core fixes
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (47 commits)
kobject: clean up the kobject add documentation a bit more
kobject: Fix kernel-doc comment first line
kobject: Remove docstring reference to kset
firmware_loader: Fix a typo ("syfs" -> "sysfs")
kobject: fix dereference before null check on kobj
Revert "driver core: platform: Fix the usage of platform device name(pdev->name)"
init/config: Do not select BUILD_BIN2C for IKCONFIG
Provide in-kernel headers to make extending kernel easier
kobject: Improve doc clarity kobject_init_and_add()
kobject: Improve docs for kobject_add/del
driver core: platform: Fix the usage of platform device name(pdev->name)
livepatch: Replace klp_ktype_patch's default_attrs with groups
cpufreq: schedutil: Replace default_attrs field with groups
padata: Replace padata_attr_type default_attrs field with groups
irqdesc: Replace irq_kobj_type's default_attrs field with groups
net-sysfs: Replace ktype default_attrs field with groups
block: Replace all ktype default_attrs with groups
samples/kobject: Replace foo_ktype's default_attrs field with groups
kobject: Add support for default attribute groups to kobj_type
driver core: Postpone DMA tear-down until after devres release for probe failure
...
The functions mbi_compose_m{b, s}i_msg may be called from non-preemptible
context. However, on RT, iommu_dma_map_msi_msg() requires to be called
from a preemptible context.
A recent patch split iommu_dma_map_msi_msg in two new functions:
one that should be called in preemptible context, the other does
not have any requirement.
The GICv3 MSI driver is reworked to avoid executing preemptible code in
non-preemptible context. This can be achieved by preparing the MSI
mapping when allocating the MSI interrupt.
Signed-off-by: Julien Grall <julien.grall@arm.com>
[maz: only call iommu_dma_prepare_msi once, fix commit log accordingly]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
ls_scfg_msi_compose_msg() may be called from non-preemptible context.
However, on RT, iommu_dma_map_msi_msg() requires to be called from a
preemptible context.
A recent patch split iommu_dma_map_msi_msg() in two new functions:
one that should be called in preemptible context, the other does
not have any requirement.
The FreeScale SCFG MSI driver is reworked to avoid executing preemptible
code in non-preemptible context. This can be achieved by preparing the
MSI maping when allocating the MSI interrupt.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
its_irq_compose_msi_msg() may be called from non-preemptible context.
However, on RT, iommu_dma_map_msi_msg requires to be called from a
preemptible context.
A recent change split iommu_dma_map_msi_msg() in two new functions:
one that should be called in preemptible context, the other does
not have any requirement.
The GICv3 ITS driver is reworked to avoid executing preemptible code in
non-preemptible context. This can be achieved by preparing the MSI
mapping when allocating the MSI interrupt.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
gicv2m_compose_msi_msg() may be called from non-preemptible context.
However, on RT, iommu_dma_map_msi_msg() requires to be called from a
preemptible context.
A recent change split iommu_dma_map_msi_msg() in two new functions:
one that should be called in preemptible context, the other does
not have any requirement.
The GICv2m driver is reworked to avoid executing preemptible code in
non-preemptible context. This can be achieved by preparing the MSI
mapping when allocating the MSI interrupt.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add a msi domain that is child to the INTA domain. Clients
uses the INTA MSI bus layer to allocate irqs in this
MSI domain.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Texas Instruments' K3 generation SoCs has an IP Interrupt Aggregator
which is an interrupt controller that does the following:
- Converts events to interrupts that can be understood by
an interrupt router.
- Allows for multiplexing of events to interrupts.
Configuration of the interrupt aggregator registers can only be done by
a system co-processor and the driver needs to send a message to this
co processor over TISCI protocol. Add the required infrastructure to
allow the allocation and routing of these events.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Texas Instruments' K3 generation SoCs has an IP Interrupt Router
that does allows for redirection of input interrupts to host
interrupt controller. Interrupt Router inputs are either from a
peripheral or from an Interrupt Aggregator which is another
interrupt controller.
Configuration of the interrupt router registers can only be done by
a system co-processor and the driver needs to send a message to this
co processor over TISCI protocol.
Add support for Interrupt Router driver over TISCI protocol.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is no need to print a message if devm_kzalloc() fails, as the
memory allocation core already takes care of that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
IRQ_DOMAIN_HIERARCHY selects IRQ_DOMAIN, hence there is no need for
drivers to select both.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Using list_add + list_sort to insert an element and keeping the list
sorted is a somewhat blunt instrument; one can find the right place to
insert in fewer lines of code than the cmp callback uses. Moreover,
walking the entire list afterwards to merge adjacent ranges is
overkill, since we know that only the just-inserted element may be
merged with its neighbours.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There's no reason to ask kmalloc() to zero the allocation, since all
the fields get initialized immediately afterwards. Except that there's
also not any reason to initialize the ->entry member, since the
element gets added to the lpi_range_list immediately.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There's no reason to do the allocation of the new lpi_range inside the
lpi_range_lock. One could change the code to avoid the allocation
altogether in case the freed range can be merged with one or two
existing ranges (in which case the allocation would naturally be done
under the lock), but it's probably not worth complicating the code for
that.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This irqchip driver uses the hwspinlock framework (coprocessor HW regs
access concurrency) for the stm32mp1-exti device.
Hence, this driver needs to handle the hwspinlock driver dependency
using the deferred probe mechanism which requires to move this driver
into a platform one with a probe() ops.
This applies only for the device which is "st,stm32mp1-exti" compatible,
the management of the other devices (st,stm32h7-exti / st,stm32-exti) is
kept unchanged (use IRQCHIP_DECLARE)
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If interrupts are enabled for a non-root GIC device that uses the
gic-pm driver, when system suspend occurs, the current interrupt
state is not saved and restored correctly and so interrupts do not
work again on resuming the system. Add a late suspend handler to
save and restore the state for these devices.
Suggested-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
gic-pm driver is using pm-clk framework to manage clock resources, where
clocks remain always ON. This happens on Tegra devices which use BPMP
co-processor to manage the clocks. Calls to BPMP are always blocking and
hence it is necessary to enable/disable clocks during prepare/unprepare
phase respectively. When pm-clk is used, prepare count of clock is not
balanced until pm_clk_remove() happens. Clock is prepared in the driver
probe() and thus prepare count of clock remains non-zero, which in turn
keeps clock ON always.
Please note that above mentioned behavior is specific to Tegra devices
using BPMP for clock management and this should not be seen on other
devices. Though this patch uses clk_bulk APIs to address the mentioned
behavior, this works fine for all devices.
To simplify gic_get_clocks() API is removed and instead probe can do
necessary setup.
Suggested-by: Mohan Kumar D <mkumard@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The word 'entirely' has been misspelt in a comment in its_msi_prepare().
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
It is useful to print which interrupt controllers are registered in the
system and which parent IRQ they use, especially given that L2 interrupt
controllers do not call request_irq() on their parent interrupt and do
not appear under /proc/interrupts for that reason.
We used to print the base register address virtual address which had
little value, use %pOF to print the path to the Device Tree node which
maps to the physical address more easily and is what people need to
troubleshoot systems.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Support. We migrate to MULTI_IRQ_HANDLER, bumps the IRQs to
offset 16, converts to SPARSE_IRQ, then we add proper subsystem
drivers in each subsystem for irqchip, GPIO and clocksource and
switch over to using these new drivers.
Next we modernize the NPE and QMGR drivers and push them down
into drivers/soc.
This has been tested on the IXP4xx NSLU2 and the Gateworks
GW2358-4.
-----BEGIN PGP SIGNATURE-----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=0U95
-----END PGP SIGNATURE-----
Merge tag 'ixp4xx-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/soc
This modernizes the IXP4xx platform and adds initial Device Tree
Support. We migrate to MULTI_IRQ_HANDLER, bumps the IRQs to
offset 16, converts to SPARSE_IRQ, then we add proper subsystem
drivers in each subsystem for irqchip, GPIO and clocksource and
switch over to using these new drivers.
Next we modernize the NPE and QMGR drivers and push them down
into drivers/soc.
This has been tested on the IXP4xx NSLU2 and the Gateworks
GW2358-4.
* tag 'ixp4xx-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik: (31 commits)
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
ARM: ixp4xx: Move IXP4xx QMGR and NPE headers
ARM: ixp4xx: Move NPE and QMGR to drivers/soc
ARM: dts: Add some initial IXP4xx device trees
ARM: ixp4xx: Add device tree boot support
ARM: ixp4xx: Add DT bindings
gpio: ixp4xx: Add OF probing support
gpio: ixp4xx: Add DT bindings
clocksource/drivers/ixp4xx: Add OF initialization support
clocksource/drivers/ixp4xx: Add DT bindings
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds support for probing and settin up the IXP4xx
irqchip from device tree.
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Fix indirect syscall tracing & seccomp filtering for big endian MIPS64
kernels, which previously loaded the syscall number incorrectly &
would always use zero.
- Fix performance counter IRQ setup for Atheros/ath79 SoCs, allowing
perf to function on those systems.
And not really a fix, but a useful addition:
- Add a Broadcom mailing list to the MAINTAINERS entry for BMIPS systems
to allow relevant engineers to track patch submissions.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXL4GhRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN15CQEA6ZtDNid9bRuD3lEOqiJTHrgUIvjA
sxVB5MwckzQ7Ir4A+wS6P4oIjlMdJxO0MZ23QlNNP+XibRt/jAz8ItLoNpcJ
=Cl5u
-----END PGP SIGNATURE-----
Merge tag 'mips_fixes_5.1_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A couple more MIPS fixes:
- Fix indirect syscall tracing & seccomp filtering for big endian
MIPS64 kernels, which previously loaded the syscall number
incorrectly & would always use zero.
- Fix performance counter IRQ setup for Atheros/ath79 SoCs, allowing
perf to function on those systems.
And not really a fix, but a useful addition:
- Add a Broadcom mailing list to the MAINTAINERS entry for BMIPS
systems to allow relevant engineers to track patch submissions"
* tag 'mips_fixes_5.1_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: perf: ath79: Fix perfcount IRQ assignment
MIPS: scall64-o32: Fix indirect syscall number load
MAINTAINERS: BMIPS: Add internal Broadcom mailing list
The IXP4xx (arch/arm/mach-ixp4xx) is an old Intel XScale
platform that has very wide deployment and use.
As part of modernizing the platform, we need to implement a
proper irqchip in the irqchip subsystem.
The IXP4xx irqchip is tightly jotted together with the GPIO
controller, and whereas in the past we would deal with this
complex logic by adding necessarily different code, we can
nowadays modernize it using a hierarchical irqchip.
The actual IXP4 irqchip is a simple active low level IRQ
controller, whereas the GPIO functionality resides in a
different memory area and adds edge trigger support for
the interrupts.
The interrupts from GPIO lines 0..12 are 1:1 mapped to
a fixed set of hardware IRQs on this IRQchip, so we
expect the child GPIO interrupt controller to go in and
allocate descriptors for these interrupts.
For the other interrupts, as we do not yet have DT
support for this platform, we create a linear irqdomain
and then go in and allocate the IRQs that the legacy
boards use. This code will be removed on the DT probe
path when we add DT support to the platform.
We add some translation code for supporting DT
translations for the fwnodes, but we leave most of that
for later.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently it's not possible to use perf on ath79 due to genirq flags
mismatch happening on static virtual IRQ 13 which is used for
performance counters hardware IRQ 5.
On TP-Link Archer C7v5:
CPU0
2: 0 MIPS 2 ath9k
4: 318 MIPS 4 19000000.eth
7: 55034 MIPS 7 timer
8: 1236 MISC 3 ttyS0
12: 0 INTC 1 ehci_hcd:usb1
13: 0 gpio-ath79 2 keys
14: 0 gpio-ath79 5 keys
15: 31 AR724X PCI 1 ath10k_pci
$ perf top
genirq: Flags mismatch irq 13. 00014c83 (mips_perf_pmu) vs. 00002003 (keys)
On TP-Link Archer C7v4:
CPU0
4: 0 MIPS 4 19000000.eth
5: 7135 MIPS 5 1a000000.eth
7: 98379 MIPS 7 timer
8: 30 MISC 3 ttyS0
12: 90028 INTC 0 ath9k
13: 5520 INTC 1 ehci_hcd:usb1
14: 4623 INTC 2 ehci_hcd:usb2
15: 32844 AR724X PCI 1 ath10k_pci
16: 0 gpio-ath79 16 keys
23: 0 gpio-ath79 23 keys
$ perf top
genirq: Flags mismatch irq 13. 00014c80 (mips_perf_pmu) vs. 00000080 (ehci_hcd:usb1)
This problem is happening, because currently statically assigned virtual
IRQ 13 for performance counters is not claimed during the initialization
of MIPS PMU during the bootup, so the IRQ subsystem doesn't know, that
this interrupt isn't available for further use.
So this patch fixes the issue by simply booking hardware IRQ 5 for MIPS PMU.
Tested-by: Kevin 'ldir' Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Currently, when irq_domain_add_linear() fails, the error code does not get
set so it returns zero which is wrong. Fix it by setting the appropriate
error code.
Fixes: 9e543e22e2 ("irqchip: Add driver for Loongson-1 interrupt controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: kernel-janitors@vger.kernel.org
Link: https://lkml.kernel.org/r/20190329062136.GQ32613@kadam
Parsing entries in an ACPI table had assumed a generic header
structure. There is no standard ACPI header, though, so less common
layouts with different field sizes required custom parsers to go through
their subtable entry list.
Create the infrastructure for adding different table types so parsing
the entries array may be more reused for all ACPI system tables and
the common code doesn't need to be duplicated.
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix sparse warning:
drivers/irqchip/irq-mvebu-sei.c:481:23: warning:
symbol 'mvebu_sei_ap806_caps' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <jason@lakedaemon.net>
Cc: <andrew@lunn.ch>
Cc: <gregory.clement@bootlin.com>
Cc: <sebastian.hesselbarth@gmail.com>
Cc: <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Link: https://lkml.kernel.org/r/20190321151448.15600-1-yuehaibing@huawei.com
mbigen_write_msg clears eventid bits of a mbigen register
when free a interrupt, because msi_domain_deactivate memset
struct msg to zero. Then multiple mbigen pins with zero eventid
will report the same interrupt number.
The eventid clear call trace:
free_irq
__free_irq
irq_shutdown
irq_domain_deactivate_irq
__irq_domain_deactivate_irq
__irq_domain_deactivate_irq
msi_domain_deactivate
platform_msi_write_msg
mbigen_write_msg
Signed-off-by: Jianguo Chen <chenjianguo3@huawei.com>
[maz: massaged subject]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The rising configuration status register (rtsr) is not banked.
As it is shared with the co-processor, it should not be written at probe
time, else the co-processor configuration will be lost.
Fixes: f9fc174550 ("irqchip/stm32: Add host and driver data structures")
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Falling and rising configuration and status registers are not banked.
As they are shared with M4 co-processor, they should not be cleared
at probe time, else M4 co-processor configuration will be lost.
Fixes: f9fc174550 ("irqchip/stm32: Add host and driver data structures")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Fix sparse warning:
drivers/irqchip/irq-mmp.c:182:29: warning:
symbol 'mmp_irq_domain_ops' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Fix sparse warnings:
drivers/irqchip/irq-brcmstb-l2.c:278:12: warning:
symbol 'brcmstb_l2_edge_intc_of_init' was not declared. Should it be static?
drivers/irqchip/irq-brcmstb-l2.c:285:12: warning:
symbol 'brcmstb_l2_lvl_intc_of_init' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The lpi_range_list is supposed to be sorted in ascending order of
->base_id (at least if the range merging is to work), but the current
comparison function returns a positive value if rb->base_id >
ra->base_id, which means that list_sort() will put A after B in that
case - and vice versa, of course.
Fixes: 880cb3cddd (irqchip/gic-v3-its: Refactor LPI allocator)
Cc: stable@vger.kernel.org (v4.19+)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We do not have any in-tree platform with this pathological setup,
and only a single system (Cavium's cns3xxx) isn't DT aware.
Let's drop the secondary GIC support for now, until we remove
the above horror altogether.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- Pseudo NMI support for arm64 using GICv3 interrupt priorities
- uaccess macros clean-up (unsafe user accessors also merged but
reverted, waiting for objtool support on arm64)
- ptrace regsets for Pointer Authentication (ARMv8.3) key management
- inX() ordering w.r.t. delay() on arm64 and riscv (acks in place by the
riscv maintainers)
- arm64/perf updates: PMU bindings converted to json-schema, unused
variable and misleading comment removed
- arm64/debug fixes to ensure checking of the triggering exception level
and to avoid the propagation of the UNKNOWN FAR value into the si_code
for debug signals
- Workaround for Fujitsu A64FX erratum 010001
- lib/raid6 ARM NEON optimisations
- NR_CPUS now defaults to 256 on arm64
- Minor clean-ups (documentation/comments, Kconfig warning, unused
asm-offsets, clang warnings)
- MAINTAINERS update for list information to the ARM64 ACPI entry
-----BEGIN PGP SIGNATURE-----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=2U56
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- Pseudo NMI support for arm64 using GICv3 interrupt priorities
- uaccess macros clean-up (unsafe user accessors also merged but
reverted, waiting for objtool support on arm64)
- ptrace regsets for Pointer Authentication (ARMv8.3) key management
- inX() ordering w.r.t. delay() on arm64 and riscv (acks in place by
the riscv maintainers)
- arm64/perf updates: PMU bindings converted to json-schema, unused
variable and misleading comment removed
- arm64/debug fixes to ensure checking of the triggering exception
level and to avoid the propagation of the UNKNOWN FAR value into the
si_code for debug signals
- Workaround for Fujitsu A64FX erratum 010001
- lib/raid6 ARM NEON optimisations
- NR_CPUS now defaults to 256 on arm64
- Minor clean-ups (documentation/comments, Kconfig warning, unused
asm-offsets, clang warnings)
- MAINTAINERS update for list information to the ARM64 ACPI entry
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (54 commits)
arm64: mmu: drop paging_init comments
arm64: debug: Ensure debug handlers check triggering exception level
arm64: debug: Don't propagate UNKNOWN FAR into si_code for debug signals
Revert "arm64: uaccess: Implement unsafe accessors"
arm64: avoid clang warning about self-assignment
arm64: Kconfig.platforms: fix warning unmet direct dependencies
lib/raid6: arm: optimize away a mask operation in NEON recovery routine
lib/raid6: use vdupq_n_u8 to avoid endianness warnings
arm64: io: Hook up __io_par() for inX() ordering
riscv: io: Update __io_[p]ar() macros to take an argument
asm-generic/io: Pass result of I/O accessor to __io_[p]ar()
arm64: Add workaround for Fujitsu A64FX erratum 010001
arm64: Rename get_thread_info()
arm64: Remove documentation about TIF_USEDFPU
arm64: irqflags: Fix clang build warnings
arm64: Enable the support of pseudo-NMIs
arm64: Skip irqflags tracing for NMI in IRQs disabled context
arm64: Skip preemption when exiting an NMI
arm64: Handle serror in NMI context
irqchip/gic-v3: Allow interrupts to be set as pseudo-NMI
...
Here are two branches that came relatively late during the linux-5.0
development cycle and have dependencies on the other branches:
- On the TI OMAP platform, the CPSW Ethernet PHY mode selection driver
is being replaced, this puts the final pieces in place
- On the DaVinci platform, the interrupt handling code in arch/arm
gets moved into a regular device driver in drivers/irqchip.
Since they both had some time in linux-next after the 5.0-rc8
release, I'm sending them along with the other updates.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=0u1N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Arnd Bergmann:
"Here are two branches that came relatively late during the linux-5.0
development cycle and have dependencies on the other branches:
- On the TI OMAP platform, the CPSW Ethernet PHY mode selection
driver is being replaced, this puts the final pieces in place
- On the DaVinci platform, the interrupt handling code in arch/arm
gets moved into a regular device driver in drivers/irqchip.
Since they both had some time in linux-next after the 5.0-rc8 release,
I'm sending them along with the other updates"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
net: ethernet: ti: cpsw: deprecate cpsw-phy-sel driver
ARM: davinci: remove intc related fields from davinci_soc_info
irqchip: davinci-cp-intc: move the driver to drivers/irqchip
ARM: davinci: cp-intc: remove redundant comments
ARM: davinci: cp-intc: drop GPL license boilerplate
ARM: davinci: cp-intc: use readl/writel_relaxed()
ARM: davinci: cp-intc: unify error handling
ARM: davinci: cp-intc: improve coding style
ARM: davinci: cp-intc: request the memory region before remapping it
ARM: davinci: cp-intc: use the new-style config structure
ARM: davinci: cp-intc: convert all hex numbers to lowercase
ARM: davinci: cp-intc: use a common prefix for all symbols
ARM: davinci: cp-intc: add the new config structures for da8xx SoCs
irqchip: davinci-cp-intc: add a new config structure
ARM: davinci: cp-intc: add a wrapper around cp_intc_init()
ARM: davinci: cp-intc: remove cp_intc.h
irqchip: davinci-aintc: move the driver to drivers/irqchip
ARM: davinci: aintc: remove unnecessary includes
ARM: davinci: aintc: remove the timer-specific irq_set_handler()
ARM: davinci: aintc: request memory region before remapping it
...
Pull irq updates from Thomas Gleixner:
"The interrupt departement delivers this time:
- New infrastructure to manage NMIs on platforms which have a sane
NMI delivery, i.e. identifiable NMI vectors instead of a single
lump.
- Simplification of the interrupt affinity management so drivers
don't have to implement ugly loops around the PCI/MSI enablement.
- Speedup for interrupt statistics in /proc/stat
- Provide a function to retrieve the default irq domain
- A new interrupt controller for the Loongson LS1X platform
- Affinity support for the SiFive PLIC
- Better support for the iMX irqsteer driver
- NUMA aware memory allocations for GICv3
- The usual small fixes, improvements and cleanups all over the
place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
irqchip/imx-irqsteer: Add multi output interrupts support
irqchip/imx-irqsteer: Change to use reg_num instead of irq_group
dt-bindings: irq: imx-irqsteer: Add multi output interrupts support
dt-binding: irq: imx-irqsteer: Use irq number instead of group number
irqchip/brcmstb-l2: Use _irqsave locking variants in non-interrupt code
irqchip/gicv3-its: Use NUMA aware memory allocation for ITS tables
irqdomain: Allow the default irq domain to be retrieved
irqchip/sifive-plic: Implement irq_set_affinity() for SMP host
irqchip/sifive-plic: Differentiate between PLIC handler and context
irqchip/sifive-plic: Add warning in plic_init() if handler already present
irqchip/sifive-plic: Pre-compute context hart base and enable base
PCI/MSI: Remove obsolete sanity checks for multiple interrupt sets
genirq/affinity: Remove the leftovers of the original set support
nvme-pci: Simplify interrupt allocation
genirq/affinity: Add new callback for (re)calculating interrupt sets
genirq/affinity: Store interrupt sets size in struct irq_affinity
genirq/affinity: Code consolidation
irqchip/irq-sifive-plic: Check and continue in case of an invalid cpuid.
irqchip/i8259: Fix shutdown order by moving syscore_ops registration
dt-bindings: interrupt-controller: loongson ls1x intc
...
gcc points out that irqs_num is not initialized when of_property_read_u32()
is an empty stub function:
Included from drivers/irqchip/irq-imx-irqsteer.c:7:
drivers/irqchip/irq-imx-irqsteer.c: In function 'imx_irqsteer_probe':
include/uapi/linux/kernel.h:13:49: error: 'irqs_num' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The same can actually happen with CONFIG_OF=y as well, though we don't
get a warning then.
Add error checking here that lets the code deal with missing or
invalid properties as well as avoid the warning.
Fixes: 28528fca49 ("irqchip/imx-irqsteer: Add multi output interrupts support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- Core pseudo-NMI handling code
- Allow the default irq domain to be retrieved
- A new interrupt controller for the Loongson LS1X platform
- Affinity support for the SiFive PLIC
- Better support for the iMX irqsteer driver
- NUMA aware memory allocations for GICv3
- A handful of other fixes (i8259, GICv3, PLIC)
-----BEGIN PGP SIGNATURE-----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=M6YA
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier
- Core pseudo-NMI handling code
- Allow the default irq domain to be retrieved
- A new interrupt controller for the Loongson LS1X platform
- Affinity support for the SiFive PLIC
- Better support for the iMX irqsteer driver
- NUMA aware memory allocations for GICv3
- A handful of other fixes (i8259, GICv3, PLIC)
One irqsteer channel can support up to 8 output interrupts.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
One group can manage 64 interrupts by using two registers (e.g. STATUS/SET).
However, the integrated irqsteer may support only 32 interrupts which
needs only one register in a group. But the current driver assume there's
a mininum of two registers in a group which result in a wrong register map
for 32 interrupts per channel irqsteer. Let's use the reg_num caculated by
interrupts per channel instead of irq_group to cover this case.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Using the irq_gc_lock/irq_gc_unlock functions in the suspend and
resume functions creates the opportunity for a deadlock during
suspend, resume, and shutdown. Using the irq_gc_lock_irqsave/
irq_gc_unlock_irqrestore variants prevents this possible deadlock.
Cc: stable@vger.kernel.org
Fixes: 7f646e9276 ("irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
[maz: tidied up $SUBJECT]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The NUMA node information is visible to ITS driver but not being used
other than handling hardware errata. ITS/GICR hardware accesses to the
local NUMA node is usually quicker than the remote NUMA node. How slow
the remote NUMA accesses are depends on the implementation details.
This patch allocates memory for ITS management tables and command
queue from the corresponding NUMA node using the appropriate NUMA
aware functions. This change improves the performance of the ITS
tables read latency on systems where it has more than one ITS block,
and with the slower inter node accesses.
Apache Web server benchmarking using ab tool on a HiSilicon D06
board with multiple numa mem nodes shows Time per request and
Transfer rate improvements of ~3.6% with this patch.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Ganapatrao Kulkarni <gkulkarni@marvell.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently on SMP host, all CPUs take external interrupts routed via
PLIC. All CPUs will try to claim a given external interrupt but only
one of them will succeed while other CPUs would simply resume whatever
they were doing before. This means if we have N CPUs then for every
external interrupt N-1 CPUs will always fail to claim it and waste
their CPU time.
Instead of above, external interrupts should be taken by only one CPU
and we should have provision to explicitly specify IRQ affinity from
kernel-space or user-space.
This patch provides irq_set_affinity() implementation for PLIC driver.
It also updates irq_enable() such that PLIC interrupts are only enabled
for one of CPUs specified in IRQ affinity mask.
With this patch in-place, we can change IRQ affinity at any-time from
user-space using procfs.
Example:
/ # cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3
8: 44 0 0 0 SiFive PLIC 8 virtio0
10: 48 0 0 0 SiFive PLIC 10 ttyS0
IPI0: 55 663 58 363 Rescheduling interrupts
IPI1: 0 1 3 16 Function call interrupts
/ #
/ #
/ # echo 4 > /proc/irq/10/smp_affinity
/ #
/ # cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3
8: 45 0 0 0 SiFive PLIC 8 virtio0
10: 160 0 17 0 SiFive PLIC 10 ttyS0
IPI0: 68 693 77 410 Rescheduling interrupts
IPI1: 0 2 3 16 Function call interrupts
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We explicitly differentiate between PLIC handler and context because
PLIC context is for given mode of HART whereas PLIC handler is per-CPU
software construct meant for handling interrupts from a particular
PLIC context.
To achieve this differentiation, we rename "nr_handlers" to "nr_contexts"
and "nr_mapped" to "nr_handlers" in plic_init().
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We have two enteries (one for M-mode and another for S-mode) in the
interrupts-extended DT property of PLIC DT node for each HART. It is
expected that firmware/bootloader will set M-mode HWIRQ line of each
HART to 0xffffffff (i.e. -1) in interrupts-extended DT property
because Linux runs in S-mode only.
If firmware/bootloader is buggy then it will not correctly update
interrupts-extended DT property which might result in a plic_handler
configured twice. This patch adds a warning in plic_init() if a
plic_handler is already marked present. This warning provides us
a hint about incorrectly updated interrupts-extended DT property.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch does following optimizations:
1. Pre-compute hart base for each context handler
2. Pre-compute enable base for each context handler
3. Have enable lock for each context handler instead
of global plic_toggle_lock
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
-------------------------------------
This pull request gets rid of mach-davinci private interrupt controller
implmentations (aintc and cp_initc) and moves them to drivers/irqchip.
mach/irqs.h usage outside of mach-davinci has been rid of.
The driver changes (input and irqchip) have been acked by respective
maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VjX6
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v5.1/soc-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/late
DaVinci SoC updates for v5.1 (part 3)
-------------------------------------
This pull request gets rid of mach-davinci private interrupt controller
implmentations (aintc and cp_initc) and moves them to drivers/irqchip.
mach/irqs.h usage outside of mach-davinci has been rid of.
The driver changes (input and irqchip) have been acked by respective
maintainers.
* tag 'davinci-for-v5.1/soc-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci: (57 commits)
ARM: davinci: remove intc related fields from davinci_soc_info
irqchip: davinci-cp-intc: move the driver to drivers/irqchip
ARM: davinci: cp-intc: remove redundant comments
ARM: davinci: cp-intc: drop GPL license boilerplate
ARM: davinci: cp-intc: use readl/writel_relaxed()
ARM: davinci: cp-intc: unify error handling
ARM: davinci: cp-intc: improve coding style
ARM: davinci: cp-intc: request the memory region before remapping it
ARM: davinci: cp-intc: use the new-style config structure
ARM: davinci: cp-intc: convert all hex numbers to lowercase
ARM: davinci: cp-intc: use a common prefix for all symbols
ARM: davinci: cp-intc: add the new config structures for da8xx SoCs
irqchip: davinci-cp-intc: add a new config structure
ARM: davinci: cp-intc: add a wrapper around cp_intc_init()
ARM: davinci: cp-intc: remove cp_intc.h
irqchip: davinci-aintc: move the driver to drivers/irqchip
ARM: davinci: aintc: remove unnecessary includes
ARM: davinci: aintc: remove the timer-specific irq_set_handler()
ARM: davinci: aintc: request memory region before remapping it
ARM: davinci: aintc: unify error handling
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cp-intc driver has now been cleaned up. Move it to drivers/irqchip
where it belongs.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The aintc driver has now been cleaned up. Move it to drivers/irqchip
where it belongs. There's no device-tree support for any dm* board so
there's no IRQCHIP_OF_DECLARE() - there's only the exported init
function called from machine code.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
riscv_hartid_to_cpuid can return invalid cpuid for a hart that is
present in DT but was never brought up.
Print the appropriate warning message and continue.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When using cpufreq on Loongson 2F MIPS platform, "poweroff"
command gets frequently stuck in syscore_shutdown(). The reason is
that i8259A_shutdown() gets called before cpufreq_suspend(), and if we
have pending work then irq_work_sync() in cpufreq_dbs_governor_stop()
gets stuck forever as we have all interrupts masked already.
irq-i8259 is registering syscore_ops using device_initcall(),
while cpufreq uses core_initcall(). Fix the shutdown order simply
by registering the irq syscore_ops during the early IRQ init instead
of using a separate initcall at later stage.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This controller appeared on Loongson-1 family MCUs
including Loongson-1B and Loongson-1C.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In current logic, its_parse_indirect_baser() will be invoked twice
when allocating Device tables. Add a *break* to omit the unnecessary
and annoying (might be ...) invoking.
Fixes: 32bd44dc19 ("irqchip/gic-v3-its: Fix the incorrect parsing of VCPU table size")
Cc: stable@vger.kernel.org
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull irq fixes from Ingo Molnar:
"irqchip driver fixes: most of them are race fixes for ARM GIC (General
Interrupt Controller) variants, but also a fix for the ARM MMP
(Marvell PXA168 et al) irqchip affecting OLPC keyboards"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Fix ITT_entry_size accessor
irqchip/mmp: Only touch the PJ4 IRQ & FIQ bits on enable/disable
irqchip/gic-v3-its: Gracefully fail on LPI exhaustion
irqchip/gic-v3-its: Plug allocation race for devices sharing a DevID
irqchip/gic-v4: Fix occasional VLPI drop
- Another GICv3 ITS fix for devices sharing the same DevID
- Don't return invalid data on exhaustion of the GICv3 LPI pool
- Fix a GICv3 field decoding bug leading to memory over-allocation
- Init GICv4 at boot time instead of lazy init
- Fix interrupt masking on PJ4
-----BEGIN PGP SIGNATURE-----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=Crvb
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates from Marc Zyngier:
- Another GICv3 ITS fix for devices sharing the same DevID
- Don't return invalid data on exhaustion of the GICv3 LPI pool
- Fix a GICv3 field decoding bug leading to memory over-allocation
- Init GICv4 at boot time instead of lazy init
- Fix interrupt masking on PJ4
Implement NMI callbacks for GICv3 irqchip. Install NMI safe handlers
when setting up interrupt line as NMI.
Only SPIs and PPIs are allowed to be set up as NMI.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Provide a higher priority to be used for pseudo-NMIs. When such an
interrupt is received, keep interrupts fully disabled at CPU level to
prevent receiving other pseudo-NMIs while handling the current one.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The values non secure EL1 needs to use for PMR and RPR registers depends on
the value of SCR_EL3.FIQ.
The values non secure EL1 sees from the distributor and redistributor
depend on whether security is enabled for the GIC or not.
To avoid having to deal with two sets of values for PMR
masking/unmasking, only enable pseudo-NMIs when GIC has non-secure view
of priorities.
Also, add firmware requirements related to SCR_EL3.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Once the boot CPU has been prepared or a new secondary CPU has been
brought up, use ICC_PMR_EL1 to mask interrupts on that CPU and clear
PSR.I bit.
Since ICC_PMR_EL1 is initialized at CPU bringup, avoid overwriting
it in the GICv3 driver.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The code to detect whether Linux has access to group0 interrupts can
prove useful in other parts of the driver.
Provide a separate function to do this.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mask the IRQ priority through PMR and re-enable IRQs at CPU level,
allowing only higher priority interrupts to be received during interrupt
handling.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- fix ccount_timer_shutdown for secondary CPUs;
- fix secondary CPU initialization;
- fix secondary CPU reset vector clash with double exception vector;
- fix present CPUs when booting with 'maxcpus' parameter;
- limit possible CPUs by configured NR_CPUS;
- issue a warning if xtensa PIC is asked to retrigger anything other
than software IRQ;
- fix masking/unmasking of the first two IRQs on xtensa MX PIC;
- fix typo in Kconfig description for user space unaligned access
feature;
- fix Kconfig warning for selecting BUILTIN_DTB.
-----BEGIN PGP SIGNATURE-----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=Pim9
-----END PGP SIGNATURE-----
Merge tag 'xtensa-20190201' of git://github.com/jcmvbkbc/linux-xtensa
Pull xtensa fixes from Max Filippov:
- fix ccount_timer_shutdown for secondary CPUs
- fix secondary CPU initialization
- fix secondary CPU reset vector clash with double exception vector
- fix present CPUs when booting with 'maxcpus' parameter
- limit possible CPUs by configured NR_CPUS
- issue a warning if xtensa PIC is asked to retrigger anything other
than software IRQ
- fix masking/unmasking of the first two IRQs on xtensa MX PIC
- fix typo in Kconfig description for user space unaligned access
feature
- fix Kconfig warning for selecting BUILTIN_DTB
* tag 'xtensa-20190201' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: SMP: limit number of possible CPUs by NR_CPUS
xtensa: rename BUILTIN_DTB to BUILTIN_DTB_SOURCE
xtensa: Fix typo use space=>user space
drivers/irqchip: xtensa-mx: fix mask and unmask
drivers/irqchip: xtensa: add warning to irq_retrigger
xtensa: SMP: mark each possible CPU as present
xtensa: smp_lx200_defconfig: fix vectors clash
xtensa: SMP: fix secondary CPU initialization
xtensa: SMP: fix ccount_timer_shutdown
Resetting bit 4 disables the interrupt delivery to the "secure
processor" core. This breaks the keyboard on a OLPC XO 1.75 laptop,
where the firmware running on the "secure processor" bit-bangs the
PS/2 protocol over the GPIO lines.
It is not clear what the rest of the bits are and Marvell was unhelpful
when asked for documentation. Aside from the SP bit, there are probably
priority bits.
Leaving the unknown bits as the firmware set them up seems to be a wiser
course of action compared to just turning them off.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
[maz: fixed-up subject and commit message]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In the unlikely event that we cannot find any available LPI in the
system, we should gracefully return an error instead of carrying
on with no LPI allocated at all.
Fixes: 38dd7c494c ("irqchip/gic-v3-its: Drop chunk allocation compatibility")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On systems or VMs where multiple devices share a single DevID
(because they sit behind a PCI bridge, or because the HW is
broken in funky ways), we reuse the save its_device structure
in order to reflect this.
It turns out that there is a distinct lack of locking when looking
up the its_device, and two device being probed concurrently can result
in double allocations. That's obviously not nice.
A solution for this is to have a per-ITS mutex that serializes device
allocation.
A similar issue exists on the freeing side, which can run concurrently
with the allocation. On top of now taking the appropriate lock, we
also make sure that a shared device is never freed, as we have no way
to currently track the life cycle of such object.
Reported-by: Zheng Xiang <zhengxiang9@huawei.com>
Tested-by: Zheng Xiang <zhengxiang9@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
1. In current implementation, every VLPI will temporarily be mapped to
the first CPU in system (normally CPU0) and then moved to the real
scheduled CPU later.
2. So there is a time window and a VLPI may be sent to CPU0 instead of
the real scheduled vCPU, in a multi-CPU virtual machine.
3. However, CPU0 may have not been scheduled as a virtual CPU after
system boots up, so the value of its GICR_VPROPBASER is unknown at
that moment.
4. If the INTID of VLPI is larger than 2^(GICR_VPROPBASER.IDbits+1),
while IDbits is also in unknown state, GIC will behave as if the VLPI
is out of range and simply drop it, which results in interrupt missing
in Guest.
As no code will clear GICR_VPROPBASER at runtime, we can safely
initialize the IDbits field at boot time for each CPU to get rid of
this issue.
We also clear Valid bit of GICR_VPENDBASER in case any ancient
programming gets left in and causes memory corrupting. A new function
its_clear_vpend_valid() is added to reuse the code in
its_vpe_deschedule().
Fixes: e643d80340 ("irqchip/gic-v3-its: Add VPE scheduling")
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
xtensa_irq_mask and xtensa_irq_unmask don't do the right thing when
called for the first two external IRQs. Treat these IRQs as per-CPU
IRQs.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
XEA2 and MX PIC can only retrigger software interrupts. Issue a warning
if an interrupt of any other type is retriggered.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- Add missing DT translation call in stm32-exti
- Fix uninitialized mutex in the GICv3 MBI support code
- Drop useless GPIO includes from the madera driver
- Fix PCI Multi-MSI allocation with aliasing devices on GICv3 ITS
-----BEGIN PGP SIGNATURE-----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=ZA7f
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates from Marc Zyngier
- Add missing DT translation call in stm32-exti
- Fix uninitialized mutex in the GICv3 MBI support code
- Drop useless GPIO includes from the madera driver
- Fix PCI Multi-MSI allocation with aliasing devices on GICv3 ITS
The way we allocate events works fine in most cases, except
when multiple PCI devices share an ITS-visible DevID, and that
one of them is trying to use MultiMSI allocation.
In that case, our allocation is not guaranteed to be zero-based
anymore, and we have to make sure we allocate it on a boundary
that is compatible with the PCI Multi-MSI constraints.
Fix this by allocating the full region upfront instead of iterating
over the number of MSIs. MSI-X are always allocated one by one,
so this shouldn't change anything on that front.
Fixes: b48ac83d6b ("irqchip: GICv3: ITS: MSI support")
Cc: stable@vger.kernel.org
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This irqchip does not use anything GPIO-related so drop
the GPIO includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The mbi_lock mutex is left uninitialized, so let's use DEFINE_MUTEX
to initialize it statically.
Fixes: 505287525c ("irqchip/gic-v3: Add support for Message Based Interrupts as an MSI controller")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Domain translate function is needed to recover irq
configuration parameters from DT node
Fixes: 927abfc446 ("irqchip/stm32: Add stm32mp1 support with hierarchy domain")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The handle_irq_perbit function loop every bit in hwirq local variable.
handle_irq_perbit(hwirq) {
for_everyt_bit_in(hwirq) {
handle_domain_irq()
->irq_exit()
->invoke_softirq()
->__do_softirq()
->local_irq_enable() // Here will cause new interrupt.
}
}
When new interrupt coming at local_irq_enable, it will finish another
interrupt handler and pull down the interrupt source. But hwirq is the
local variable for handle_irq_perbit(), it can't get new interrupt
controller pending reg status. So we need update hwirq with pending reg
in every loop.
Also change write_relax to writel could prevent stw from fast retire.
When local_irq is enabled, intc regs is really set-in.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Lu Baoquan <lu.baoquan@intellif.com>
- switch to generated syscall table
- switch ptrace to regsets, use regsets for core dumps
- complete tracehook implementation
- add syscall tracepoints support
- add jumplabels support
- add memtest support
- drop unused/duplicated code from entry.S, ptrace.c, coprocessor.S,
elf.h and syscall.h
- clean up warnings caused by WSR/RSR macros
- clean up DTC warnings about SPI controller node names in xtfpga.dtsi
- simplify coprocessor.S
- get rid of explicit 'l32r' instruction usage in assembly
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEK2eFS5jlMn3N6xfYUfnMkfg/oEQFAlwmam4THGpjbXZia2Jj
QGdtYWlsLmNvbQAKCRBR+cyR+D+gRFZAD/480EcCMJxYjeo232tzWRTfcf8Al0Bh
sBgI1s5m7/m7bcX+mqGgJGirDqjc90sTbHum9vH5BesCc5A4tlZm82C++pGxKI7T
icKHlIfPcvefMsZlNIh8dTL5WB0Bw/trc3KLZJdadCb069dI6rKUg69ssy6nvZjF
nU3KZGZa0jpz/AtXNBVEZjaipmemn/j0QjLzGGrpKiw8zGvsz4+EG3DO7kP1w3tZ
LeF0JLb3deyq/rtCLNKSRD23Gw0iwuf/eidlQ8nEH9pMxCsXY9DjYtjzToZ58c6A
ZnFJxYTd7Ot5oNhONhVkgQ583hLbJ/pki1sPI0y77K1FLSLROz7U/pE3DO6ETMvX
sb1+A35qUwaYj8FswZz9g0vJm+YJqvR7K1gbGE/6szoK99FNRvxAUwBQ0BXJM1cR
wD7gNXIIEd6J8K83oOBtwKSTmOyA4bG1oiq7lgZCq91MJtQ5CYWWwONqKnsMoC/E
AGa/sEw0PD5kGR5n7fzuXg9gmGRHrgjeln/iYMTVfWwrGL1YMOxJg7O9sFai/X86
ozSjzEa3PDCbBF5YvKb55fq5YFHpFXTpfX6lwpBausOI0c+20Boc4i1XcCZCjYOG
xxSBSt2M8Fff/w5Aj/WlYaBy2qPR+2VpxI3LSnfUP+loVfuKZyaKtsUK0QkM1ODr
XSmdQ7kI/xZ2Tg==
=LqC4
-----END PGP SIGNATURE-----
Merge tag 'xtensa-20181228' of git://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa updates from Max Filippov:
- switch to generated syscall table
- switch ptrace to regsets, use regsets for core dumps
- complete tracehook implementation
- add syscall tracepoints support
- add jumplabels support
- add memtest support
- drop unused/duplicated code from entry.S, ptrace.c, coprocessor.S,
elf.h and syscall.h
- clean up warnings caused by WSR/RSR macros
- clean up DTC warnings about SPI controller node names in xtfpga.dtsi
- simplify coprocessor.S
- get rid of explicit 'l32r' instruction usage in assembly
* tag 'xtensa-20181228' of git://github.com/jcmvbkbc/linux-xtensa: (25 commits)
xtensa: implement jump_label support
xtensa: implement syscall tracepoints
xtensa: implement tracehook functions and enable HAVE_ARCH_TRACEHOOK
xtensa: enable CORE_DUMP_USE_REGSET
xtensa: implement TIE regset
xtensa: implement task_user_regset_view
xtensa: call do_syscall_trace_{enter,leave} selectively
xtensa: use NO_SYSCALL instead of -1
xtensa: define syscall_get_arch()
Move EM_XTENSA to uapi/linux/elf-em.h
xtensa: support memtest
xtensa: don't use l32r opcode directly
xtensa: xtfpga.dtsi: fix dtc warnings about SPI
xtensa: don't clear cpenable unconditionally on release
xtensa: simplify coprocessor.S
xtensa: clean up WSR*/RSR*/get_sr/set_sr
xtensa: drop unused declarations from elf.h
xtensa: clean up syscall.h
xtensa: drop unused coprocessor helper functions
xtensa: drop custom PTRACE_{PEEK,POKE}{TEXT,DATA}
...
Here is the nds32 patch set based on 4.20-rc1.
Contained in here are
1. Perf support
2. Power management support
3. FPU support
4. Hardware prefetcher support
5. Build error fixed
6. Performance enhancement
These are the LTP20170427 testing results.
Total Tests: 1902
Total Skipped Tests: 603
Total Failures: 410
Kernel Version: 4.20.0-rc1-00016-ge0db606bc023
Machine Architecture: nds32
Hostname: greentime-d15-ae3xx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=Gy5E
-----END PGP SIGNATURE-----
Merge tag 'nds32-for-linus-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux
Pull nds32 updates from Greentime Hu:
- Perf support
- Power management support
- FPU support
- Hardware prefetcher support
- Build error fixed
- Performance enhancement
* tag 'nds32-for-linus-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux:
nds32: support hardware prefetcher
nds32: Fix the items of hwcap_str ordering issue.
math-emu/soft-fp.h: (_FP_ROUND_ZERO) cast 0 to void to fix warning
math-emu/op-2.h: Use statement expressions to prevent negative constant shift
nds32: support denormalized result through FP emulator
nds32: Support FP emulation
nds32: nds32 FPU port
nds32: Remove duplicated include from pm.c
nds32: Power management for nds32
nds32: Add document for NDS32 PMU.
nds32: Add perf call-graph support.
nds32: Perf porting
nds32: Fix bug in bitfield.h
nds32: Fix gcc 8.0 compiler option incompatible.
nds32: Fill all TLB entries with kernel image mapping
nds32: Remove the redundant assignment
Pull Devicetree updates from Rob Herring:
"The biggest highlight here is the start of using json-schema for DT
bindings. Being able to validate bindings has been discussed for years
with little progress.
- Initial support for DT bindings using json-schema language. This is
the start of converting DT bindings from free-form text to a
structured format.
- Reworking of initrd address initialization. This moves to using the
phys address instead of virt addr in the DT parsing code. This
rework was motivated by CONFIG_DEV_BLK_INITRD causing unnecessary
rebuilding of lots of files.
- Fix stale phandle entries in phandle cache
- DT overlay validation improvements. This exposed several memory
leak bugs which have been fixed.
- Use node name and device_type helper functions in DT code
- Last remaining conversions to using %pOFn printk specifier instead
of device_node.name directly
- Create new common RTC binding doc and move all trivial RTC devices
out of trivial-devices.txt.
- New bindings for Freescale MAG3110 magnetometer, Cadence Sierra
PHY, and Xen shared memory
- Update dtc to upstream version v1.4.7-57-gf267e674d145"
* tag 'devicetree-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (68 commits)
of: __of_detach_node() - remove node from phandle cache
of: of_node_get()/of_node_put() nodes held in phandle cache
gpio-omap.txt: add reg and interrupts properties
dt-bindings: mrvl,intc: fix a trivial typo
dt-bindings: iio: magnetometer: add dt-bindings for freescale mag3110
dt-bindings: Convert trivial-devices.txt to json-schema
dt-bindings: arm: mrvl: amend Browstone compatible string
dt-bindings: arm: Convert Tegra board/soc bindings to json-schema
dt-bindings: arm: Convert ZTE board/soc bindings to json-schema
dt-bindings: arm: Add missing Xilinx boards
dt-bindings: arm: Convert Xilinx board/soc bindings to json-schema
dt-bindings: arm: Convert VIA board/soc bindings to json-schema
dt-bindings: arm: Convert ST STi board/soc bindings to json-schema
dt-bindings: arm: Convert SPEAr board/soc bindings to json-schema
dt-bindings: arm: Convert CSR SiRF board/soc bindings to json-schema
dt-bindings: arm: Convert QCom board/soc bindings to json-schema
dt-bindings: arm: Convert TI nspire board/soc bindings to json-schema
dt-bindings: arm: Convert TI davinci board/soc bindings to json-schema
dt-bindings: arm: Convert Calxeda board/soc bindings to json-schema
dt-bindings: arm: Convert Altera board/soc bindings to json-schema
...
- A bunch of new irqchip drivers (RDA8810PL, Madera, imx-irqsteer)
- Updates for new (and old) platforms (i.MX8MQ, F1C100s)
- A number of SPDX cleanups
- A workaround for a very broken GICv3 implementation
- A platform-msi fix
- Various cleanups
-----BEGIN PGP SIGNATURE-----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=1Mk9
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- A bunch of new irqchip drivers (RDA8810PL, Madera, imx-irqsteer)
- Updates for new (and old) platforms (i.MX8MQ, F1C100s)
- A number of SPDX cleanups
- A workaround for a very broken GICv3 implementation
- A platform-msi fix
- Various cleanups
If a hwspinlock is defined in device tree use it to protect
configuration registers.
Do not request for hwspinlock during the exti driver init since the
hwspinlock driver is not probed yet at that stage and the exti driver
does not support deferred probe.
Instead of this, postpone the hwspinlock request at the first time the
hwspinlock is actually needed.
Use the hwspin_trylock_raw() API which is the most appropriated here
Indeed:
- hwspin_lock_() calls are under spin_lock protection (chip_data->rlock
or gc->lock).
- the _timeout() API relies on jiffies count which won't work if IRQs
are disabled which is the case here (a large part of the IRQ setup is
done atomically (see irq/manage.c))
As a consequence implement the retry/timeout lock from here. And since
all of this is done atomically, reduce the timeout delay to 1 ms.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The irqsteer block is a interrupt multiplexer/remapper found on the
i.MX8 line of SoCs.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Cirrus Logic Madera codecs (Cirrus Logic CS47L35/85/90/91 and WM1840)
are highly complex devices containing up to 7 programmable DSPs and many
other internal sources of interrupts plus a number of GPIOs that can be
used as interrupt inputs. The large number (>150) of internal interrupt
sources are managed by an on-board interrupt controller.
This driver provides the handling for the interrupt controller. As the
codec is accessed via regmap, we can make use of the generic IRQ
functionality from regmap to do most of the work. Only around half of
the possible interrupt source are currently of interest from the driver
so only this subset is defined. Others can be added in future if needed.
The KConfig options are not user-configurable because this driver is
mandatory so is automatically included when the parent MFD driver is
selected.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Go over the IRQ subsystem source code (including irqchip drivers) and
fix common typos in comments.
No change in functionality intended.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
The GPC node on i.MX8MQ can not claim to be compatible with the i.MX7D
GPC, as the power gating part has some significant differences. Thus we
can not rely on the irqchip being probed with the old compatible.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In case of error, the function of_io_request_and_map() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: d852e62ad6 ("irqchip: Add RDA8810PL interrupt driver")
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The -Wimplicit-fallthrough option requires that the /* fall through */
comment is placed in the 'case' statement that falls through, rather
than in the following one. Case seems to matter as well.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Access to GICR_WAKER is restricted on msm8996 SoC in Hypervisor.
Its been more than 2+ years of wait for this to be fixed, which has
no hopes to be fixed. This change was introduced for the "lead device"
on msm8996 platform. It looks like all publicly available msm8996 and
other Qualcomm SoCs have this implementation.
So add a quirk to not access this register on msm8996.
With this quirk MSM8996 can at least boot out of mainline,
which can help community to work with boards based on MSM8996 and other
SoCs with have this restrictions. This Quirk is based on device tree
compatible string.
Without this patch Qualcomm DB820c board reboots when GICR_WAKER
is accessed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds support to device tree based quirks based on
device tree compatible string.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds support for suniv Allwinner ARMv5 F1C100s SoC which has
stripped version of interrupt controller that found in A10/A13.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch moves IC specific register offsets to sun4i_irq_chip_data
struct in order to support different chips.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to support different chips, IC specific data should be hold in
a struct. This patch moves irq_base and irq_domain global variables to
struct.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Make error messages more consistent by making sure each starts with
"%pOF:".
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: cphealy@gmail.com
Cc: l.stach@pengutronix.de
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Convert all instances of 1 << x to BIT(x) for consistency with other
kernel code.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: cphealy@gmail.com
Cc: l.stach@pengutronix.de
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Move identical offset calculation code into a small helper function
and make use of it in the rest of the code.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: cphealy@gmail.com
Cc: l.stach@pengutronix.de
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Varaible 'reg' in imx_gpcv2_irq_set_wake() has no users. Remove it.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: cphealy@gmail.com
Cc: l.stach@pengutronix.de
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Adopt the SPDX license identifier headers to ease license compliance
management.
Cc: Simon Arlott <simon@arlott.org>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
WSR and RSR are too generic and collide with other macro definitions in
the kernel causing warnings in allmodconfig builds. Drop WSR and RSR
macros and WSR_* and RSR_* variants. Change get_sr and set_sr to
xtensa_get_sr and xtensa_set_sr. Fix up users.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
There are three sleep states in nds32:
suspend to idle,
suspend to standby,
suspend to ram
In suspend to ram, we use the 'standby' instruction to emulate
power management device to hang the system util wakeup source
send wakeup events to break the loop.
First, we push the general purpose registers and system registers
to stack. Second, we translate stack pointer to physical address
and store to memory to save the stack pointer. Third, after write
back and invalid the cache we hang in 'standby' intruction.
When wakeup source trigger wake up events, the loop will be break
and resume the system.
Signed-off-by: Nick Hu <nickhu@andestech.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Greentime Hu <greentime@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
The devm_ioremap_resource() function never returns NULL, it returns
error pointers.
Fixes: 61ce8d8d8a ("irqchip/irq-mvebu-sei: Add new driver for Marvell SEI")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: kernel-janitors@vger.kernel.org
Link: https://lkml.kernel.org/r/20181013102246.GD16086@mwanda
Release, which has been through 10 rounds of review on mailing list.
We almost got the Acked-by/Reviewed-by of all patches except "Process
management and Signal", but all've been tested.
Here is the LTP-20180118 test report:
-----------------------------------------------
Total Tests: 1298
Total Skipped Tests: 281
Total Failures: 10
Kernel Version: 4.19.0+
Machine Architecture: csky
Hostname: buildroot
-----------------------------------------------
This patchset adds architecture support to Linux for C-SKY's 32-bit embedded
There are two ABI versions with several CPU cores in this patchset:
ABIv1: 610 (16-bit instruction, 32-bit data path, VIPT Cache ...)
ABIv2: 807 810 860 (16/32-bit variable length instruction, PIPT Cache,
SMP ...)
More information: http://en.c-sky.com
The development repo: https://github.com/c-sky/csky-linux
ABI Documentation: https://github.com/c-sky/csky-doc
Here is the pre-built cross compiler for fast test from our CI:
https://gitlab.com/c-sky/buildroot/-/jobs/101608095/artifacts/file/output/images/csky_toolchain_qemu_csky_ck807f_4.18_glibc_defconfig_482b221e52908be1c9b2ccb444255e1562bb7025.tar.xz
We use buildroot as our CI-test enviornment. "LTP, Lmbench ..."
will be tested for every commit. See here for more details:
https://gitlab.com/c-sky/buildroot/pipelines
We'll continouslly improve csky subsystem in future.
Changes in v10:
- Remove duplicated headers in asm/Kbuild and uapi/asm/Kbuild.
- Change to (__NR_arch_specific_syscall + 1) in unistd.h.
- Drop dword access for get_user_size patch.
- Involve the interrupt controller drivers after got Reviewed-by.
Changes in v9:
- Remove unused code in smp.c and use per_cpu for ipi_data.
- Fixup r15 register access in abiv1/alignment.c.
- Improve the changelog comment in commit-msg.
Changes in v8:
- Pass make allmodconfig.
- Implement abiv1 get_user_dword().
- Remove set_irq_mapping() used by driver in smp.c.
Changes in v7:
- Use checkpatch.pl to check all patches and fixup as possible.
- Remove github.com/c-sky print in bootup.
- Give a return in DMA_ATTR_NON_CONSISTENT in csky_dma_alloc_atomic().
- Remove the NSIGXXX in fpu.c and use force_sig_fault() in fpu.c.
- Remove irq.h and add it in asm/Kbuild.
- Use byteswap helpers in abiv1/bswapXi.c.
- Fixup arch_sync_dma() only with one page problem.
Changes in v6:
- use asm-generic/bitops/atomic.h for all in asm/bitops.h
- fix flush_cache_range and tlb_start_vma
- fix compile error with include linux/bug.h in cmpxchg.h
- improve the comment
Changes in v5:
- remove redundant smp_mb operations in spinlock.h
- add commit message for dt-bindings docs
- add CPUHP_AP_CSKY_TIMER_STARTING in hotplug.h for csky_mptimer
- add COMPILE_TEST for timer-gx6605s Kconfig
- seperate csky two interrupt controllers with 2 patches
- add MAINTAINERS patch for csky
- move IPI_IRQ into csky_mptimer, fixup irq_mapping problem
- coding convension
Changes in v4:
- cleanup defconfig
- use ksys_ in syscall.c
- remove wrong comment in vdso.c
- Use GENERIC_IRQ_MULTI_HANDLER
- optimize the memset.c
- fixup dts warnings
- remove big-endian in byteorder.h
Changes in v3:
dc560f1 csky: change to EM_CSKY 252 for elf.h
2ac3ddf csky: remove gx6605s.dts
af00b8c csky: add defconfig and qemu.dts
6c87efb csky: remove the deprecate name.
f6dda39 csky: add dt-bindings doc.
d9f02a8 csky: remove KERNEL_VERSION in upstream branch
7bd663c csky: Use kernel/dma/noncoherent.c
1544c09 csky: bugfix emmc hang up LINS-976
e963271 csky: cleanup include/asm/Kbuild
cd267ba csky: remove CSKY_DEBUG_INFO
78950da csky: remove dcache invalid.
13fe51d csky: remove csum_ipv6_magic(), use generic one.
a7372db csky: bugfix CK810 access twice error.
1bb7c69 csky: bugfix add gcc asm memory for barrier.
5ea3257 csky: add -msoft-float instead of -mfloat-abi=soft.
38b037d csky: bugfix losing cache flush range.
ab5e8c4 csky: Add ticket-spinlock and qrwlock support.
c9aaec5 csky: rename cskyksyms.c to libgcc_ksyms.c
28c5e48 csky: avoid the MB on failure: trylock
f929c97 csky: bugfix idly4 may cause exception.
09dc496 csky: Use GENERIC_ASHLDI3/ASHRDI3 etc
6ecc99d csky: optimize smp boot code.
16f50df csky: asm/bug.h simple implement.
0ba532a csky: csky asm/atomic.h added.
df66947 csky: asm/compat.h added
275a06f csky: String operations optimization
4c021dd csky: ck860 SMP memory barrier optimize
fc39c66 csky: Add wait/doze/stop
d005144 csky: add GENERIC_ALLOCATOR
4a10074 csky: bugfix cma failed for highmem.
9f2ca70 csky: CMA supported :)
53791f4 csky: optimize csky_dma_alloc_nonatomic
974676e csky: optimize the cpuinfo printf.
2538669 csky: bugfix make headers_install error.
1158d0c csky: prevent hard-float and vdsp instructions.
dc3c856 csky: increase Normal Memory to 1GB
6ee5932 csky: bugfix qemu mmu couldn't support 0xffffe000
1d7dfb8 csky: csky_dma_alloc_atomic added.
caf6610 csky: restruct the fixmap memory layout.
5a17eaa csky: use -Wa,-mcpu=ckxxxfv to the as.
4d51829 csky: use Kconfig.hz.
f3f88fa csky: BUGFIX add -mcpu=ck860f support
6192fd1 csky: support ck860 fpu.
7aa5e01 csky: BUGFIX add smp_mb before ldex.
15758e2 csky: BUGFIX tlbi couldn't handle ASID in another CPU core.
d69640d csky: enable tlbi.vas to flush one tlb entry
Changes in v2:
a29bfc8 csky: add pre_mmu_init, move misc mmu setup to mm/init.c
4eab702 csky: no need kmap for !VM_EXEC.
6770eec csky: Use TEE as the name of CPU Trusted Execution Enviornment.
a56c8c7 csky: update the cache flush api.
1a48a95 csky: add C-SKY Trust Zone.
b7a0a44 csky: use CONFIG_RAM_BASE as the same in memory of dts.
15adf81 csky: remove unused code.
35c0d97 csky: bugfix lost a cacheline flush when start isn't cacheline-aligned.
4e82c8d csky: use tlbi.alls for ck860 smp temporary.
ae7149e csky: bugfix use kmap_atomic() to prevent no mapped addr.
5538795 csky: bugfix user access in kernel space.
a7aa591 csky: add 16bit user space bkpt.
0de70ec csky: add sync.is for cmpxchg in SMP.
c5c08a1 csky: seperate sync.is and sync for SMP and Non-SMP.
dbbf4dc csky: use sync.is for ck860 mb().
f33f8da csky: rewrite the alignment implement.
68152c7 csky: bugfix alignment pt_regs error.
d618d43 csky: support set_affinity for irq balance in SMP
ebf86c9 csky: bugfix compile error without CONFIG_SMP.
8537eea csky: remove debug code.
4ebc051 csky: bugfix compile error with linux-4.9.56
75a938e csky: C-SKY SMP supported.
0eebc07 csky: use internal function for map_sg.
3d29751 csky: bugfix can't support highmem
b545d2a csky: bugfix r26 is the link reg for jsri_to_jsr.
9e3313a csky: bugfix sync tls for abiv1 in ptrace.
587a0d2 csky: use __NR_rt_sigreturn in asm-generic.
f562b46 csky: bugfix gpr_set & fpr_set
f57266f csky: bugfix fpu_fpe_helper excute mtcr mfcr.
c676669 csky: bugfix ave is default enable on reset.
d40d34d csky: remove unused sc_mask in sigcontext.h.
274b7a2 csky: redesign the signal's api
7501771 csky: bugfix forget restore usp.
923e2ca csky: re-struct the pt_regs for regset.
2a1e499 csky: fixup config.
ada81ec csky: bugfix abiv1 compile error.
e34acb9 csky: bugfix abiv1 couldn't support -mno-stack-size.
ec53560 csky: change irq map, reserve soft_irq&private_irq space.
c7576f7 csky: bugfix modpost warning with -mno-stack-size
c8ff9d4 csky: support csky mp timer alpha version.
deabaaf csky: update .gitignore.
574815c csky: bugfix compile error with abiv1 in 4.15
0b426a7 csky: bugfix format of cpu verion id.
083435f csky: irq-csky-v2 alpha init.
21209e5 csky: add .gitignore
73e19b4 csky: remove FMFS_FPU_REGS/FMTS_FPU_REGS
07e8fac csky: add fpu regset in ptrace.c
cac779d csky: add CSKY_VECIRQ_LEGENCY for SOC bug.
54bab1d csky: move usp into pt_regs.
b167422 csky: support regset for ptrace.
a098d4c csky: remove ARCH_WANT_IPC_PARSE_VERSION
fe61a84 csky: add timer-of support.
27702e2 csky: bugfix boot error.
ebe3edb csky: bugfix gx6605s boot failed - add __HEAD to head.section for head.S - move INIT_SECTION together to fix compile warning.
7138cae csky: coding convension for timer-nationalchip.c
fa7f9bb csky: use ffs instead of fls.
ddc9e81 csky: change to generic irq chip for irq-csky.c
e9be8b9 irqchip: add generic irq chip for irq-nationalchip
2ee83fe csky: add set_handle_irq(), ref from openrisc & arm.
74181d6 csky: use irq_domain_add_linear instead of leagcy.
fa45ae4 csky: bugfix setup stroge order for uncached.
eb8030f csky: add HIGHMEM config in Kconfig
4f983d4 csky: remove "default n" in Kconfig
2467575 csky: use asm-generic/signal.h
77438e5 csky: coding conventions for irq.c
2e4a2b4 csky: optimize the cache flush ops.
96e1c58 csky: add CONFIG_CPU_ASID_BITS.
9339666 csky: add cprcr() cpwcr() for abiv1
ff05be4 csky: add THREAD_SHIFT define in asm/page.h
52ab022 csky: add mfcr() mtcr() in asm/reg_ops.h
bdcd8f3 csky: revert back Kconfig select.
590c7e6 csky: bugfix compile error with CONFIG_AUDIT
1989292 csky: revert some back with cleanup unistd.h
f1454fe csky: cleanup unistd.h
5d2985f csky: cleanup Kconfig and Makefile.
423d97e csky: cancel subdirectories
cae2af4 csky: use asm-generic/fcntl.h
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE2KAv+isbWR/viAKHAXH1GYaIxXsFAlvT4KESHHJlbl9ndW9A
Yy1za3kuY29tAAoJEAFx9RmGiMV7xvoP/RpZO14XK0LeKjP9DllhvxSF49iL2MxC
GGqPpRzYvzjl6KNd8VxwUbi7VCMJd8et3FF7lIfRaLxeHgj/kqk6X3JIzFON6rom
3dRzy5XDV1bzsaZoqRK2lysGJwVmkh+CQVpmGvdSrziFPqoHyzALF0T2ggX97lft
HVpkg/ugiamb7a3p8U2oI5p8V05+beXgTFAqb5QszJwmPVFNaqs6CvnjmFJxJ4L8
EAyXZ6MXjgLPE0z+0ACCkBcK66ejneTVrcGaxgNaMT5kzcE5qCF6bTZxRx7YxwnA
tbk8q+/dd5W1pbfBff3NifXeSHvkWqn7vmTq+PqGnid/92cJTzjspjaakZgEfbTP
F8kB5jND54hlchdKfqrfoOpi3W8UYEfqdf1BHWgqsptWpq6GoTMJJE6y6rfvy1E7
r/F8rSKJlc8SxVa8/VIQqO4LbSlxm/wnO7sGoeYi8TjO3ZMCBIm4Had0f5uJTgdH
WENC5WP1xyle5BsL3BJiTLQl1qappWptX44YaVod2A9HtdIOsVWCFNdhFPCis1jX
RaoP7pHBxQ5Q6r8Nue9bBa2F3gK7IOh1EKEJ821AgA9Pz2Gm8wZ1XzsPqFCiAkkS
PcIuZQl7l/eVoiXXEqUTQFlzL4K8WnvKCYAdRZWklGKfE0Ek5RD+KVXhqFE8Ujz4
xa+OgEzn5cQA
=kHer
-----END PGP SIGNATURE-----
Merge tag 'csky-for-linus-4.20' of https://github.com/c-sky/csky-linux
Pull C-SKY architecture port from Guo Ren:
"This contains the Linux port for C-SKY(csky) based on linux-4.19
Release, which has been through 10 rounds of review on mailing list.
More information:
http://en.c-sky.com
The development repo:
https://github.com/c-sky/csky-linux
ABI Documentation:
https://github.com/c-sky/csky-doc
Here is the pre-built cross compiler for fast test from our CI:
https://gitlab.com/c-sky/buildroot/-/jobs/101608095/artifacts/file/output/images/csky_toolchain_qemu_csky_ck807f_4.18_glibc_defconfig_482b221e52908be1c9b2ccb444255e1562bb7025.tar.xz
We use buildroot as our CI-test enviornment. "LTP, Lmbench ..." will
be tested for every commit. See here for more details:
https://gitlab.com/c-sky/buildroot/pipelines
We'll continouslly improve csky subsystem in future"
Arnd acks, and adds the following notes:
"I did a thorough review of the ABI, which as usual mainly consists of
spotting any files that don't use the asm-generic ABI itself, and
having it changed to it matches exactly what we do on other new
architectures.
I also looked at every other patch and commented on maybe half of them
where I saw something that did not quite seem right. Others have
reviewed specific patches in greater depth. I'm sure that one could
fine more of the minor details, but as long as they are not ABI
relevant, they can be fixed later.
The only patch that is part of the ABI and that nobody reviewed is the
signal handling. This is one of the areas I never worked on in much
detail. I did not see anything wrong with it, but I also don't know
what the problems with the other architectures are here, and we seem
to be hitting issues occasionally, and we never managed to generalize
this enough for new architectures to have a trivial implementation.
I was originally hoping that we could have the 64-bit time_t
interfaces ready in time to completely drop the 32-bit ones, but that
did not happen. We might still remove them in the next merge window
depending on whether the libc upstream people prefer to keep them or
not.
One more general comment: I think this may well be the last new CPU
architecture we ever add to the kernel. Both nds32 and c-sky are made
by companies that also work on risc-v, and generally speaking risc-v
seems to be killing off any of the minor licensable instruction set
projects, just like ARM has mostly killed off the custom
vendor-specific instruction sets already.
If we add another architecture in the future, it may instead be
something like the LLVM bitcode or WebAssembly, who knows?"
To which Geert Uytterhoeven pipes in about another architecture still in
the pipeline: Kalray MPPA.
* tag 'csky-for-linus-4.20' of https://github.com/c-sky/csky-linux: (24 commits)
dt-bindings: interrupt-controller: C-SKY APB intc
irqchip: add C-SKY APB bus interrupt controller
dt-bindings: interrupt-controller: C-SKY SMP intc
irqchip: add C-SKY SMP interrupt controller
MAINTAINERS: Add csky
dt-bindings: Add vendor prefix for csky
dt-bindings: csky CPU Bindings
csky: Misc headers
csky: SMP support
csky: Debug and Ptrace GDB
csky: User access
csky: Library functions
csky: ELF and module probe
csky: Atomic operations
csky: IRQ handling
csky: VDSO and rt_sigreturn
csky: Process management and Signal
csky: MMU and page table management
csky: Cache and TLB routines
csky: System Call
...
This patch set contains a lot (at least, for me) of improvements to the
RISC-V kernel port:
* The removal of some cacheinfo values that were bogus.
* On systems with F but without D the kernel will not show the F
extension to userspace, as it isn't actually supported.
* Support for futexes.
* Removal of some unused code.
* Cleanup of some menuconfig entries.
* Support for systems without a floating-point unit, and for building
kernels that will never use the floating-point unit.
* More fixes to the RV32I port, which regressed again. It's really time
to get this into a regression test somewhere so I stop breaking it.
Thanks to Zong for resurrecting it again!
* Various fixes that resulted from a year old review of our original
patch set that I finally got around to.
* Various improvements to SMP support, largely based around having
switched to logical hart numbering, as well as some interrupt
improvements. This one is in the same patch set as above, thanks to
Atish for sheparding everything though as my patch set was a bit of a
mess.
I'm pretty sure this is our largest patch set since the original kernel
contribution, and it's certainly the one with the most contributors.
While I don't have anything else I know I'm going to submit for the
merge window, I would be somewhat surprised if I didn't screw anything
up.
Thanks for the help, everyone!
-----BEGIN PGP SIGNATURE-----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=YL+A
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-4.20-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This patch set contains a lot (at least, for me) of improvements to
the RISC-V kernel port:
- The removal of some cacheinfo values that were bogus.
- On systems with F but without D the kernel will not show the F
extension to userspace, as it isn't actually supported.
- Support for futexes.
- Removal of some unused code.
- Cleanup of some menuconfig entries.
- Support for systems without a floating-point unit, and for building
kernels that will never use the floating-point unit.
- More fixes to the RV32I port, which regressed again. It's really
time to get this into a regression test somewhere so I stop
breaking it. Thanks to Zong for resurrecting it again!
- Various fixes that resulted from a year old review of our original
patch set that I finally got around to.
- Various improvements to SMP support, largely based around having
switched to logical hart numbering, as well as some interrupt
improvements. This one is in the same patch set as above, thanks to
Atish for sheparding everything though as my patch set was a bit of
a mess.
I'm pretty sure this is our largest patch set since the original
kernel contribution, and it's certainly the one with the most
contributors. While I don't have anything else I know I'm going to
submit for the merge window, I would be somewhat surprised if I didn't
screw anything up.
Thanks for the help, everyone!"
* tag 'riscv-for-linus-4.20-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux: (31 commits)
RISC-V: Cosmetic menuconfig changes
riscv: move GCC version check for ARCH_SUPPORTS_INT128 to Kconfig
RISC-V: remove the unused return_to_handler export
RISC-V: Add futex support.
RISC-V: Add FP register ptrace support for gdb.
RISC-V: Mask out the F extension on systems without D
RISC-V: Don't set cacheinfo.{physical_line_partition,attributes}
RISC-V: Show IPI stats
RISC-V: Show CPU ID and Hart ID separately in /proc/cpuinfo
RISC-V: Use Linux logical CPU number instead of hartid
RISC-V: Add logical CPU indexing for RISC-V
RISC-V: Use WRITE_ONCE instead of direct access
RISC-V: Use mmgrab()
RISC-V: Rename im_okay_therefore_i_am to found_boot_cpu
RISC-V: Rename riscv_of_processor_hart to riscv_of_processor_hartid
RISC-V: Provide a cleaner raw_smp_processor_id()
RISC-V: Disable preemption before enabling interrupts
RISC-V: Comment on the TLB flush in smp_callin()
RISC-V: Filter ISA and MMU values in cpuinfo
RISC-V: Don't set cacheinfo.{physical_line_partition,attributes}
...
The driver is for C-SKY APB bus interrupt controller. It's a simple
interrupt controller which use pending reg to detect the irq and use
enable/disable reg to mask/unmask interrupt sources.
A lot of SOCs based on C-SKY CPU use the interrupt controller as root
controller.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
The driver is for C-SKY SMP interrupt controller. It support 16
soft-irqs, 16 private-irqs, and 992 max external-irqs, a total of
1024 interrupts.
C-SKY CPU 807/810/860 SMP/non-SMP could use it.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Setup the cpu_logical_map during boot. Moreover, every SBI call
and PLIC context are based on the physical hartid. Use the logical
CPU to hartid mapping to pass correct hartid to respective functions.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
It's a bit confusing exactly what this function does: it actually
returns the hartid of an OF processor node, failing with -1 on invalid
nodes. I've changed the name to _hartid() in order to make that a bit
more clear, as well as adding a comment.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
[Atish: code comment formatting update]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
LPIs use the same priority value as other GIC interrupts.
Make the GIC default priority definition visible to ITS implementation
and use this same definition for LPI priorities.
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Multiple interrupts pending for a CPU is actually rare. Doing an
acknowledge loop does not give much better performance or even can
deteriorate them.
Do not loop when an interrupt has been acknowledged, just return
from interrupt and wait for another one to be raised.
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
So far the ICU only handled NSR interrupts through GICP. An SEI driver
provides an MSI domain through which it is possible to raise SEI, so
let's add SEI support to the ICU driver.
Handle the NSR probe function in a more generic way to support other
type of interrupts.
Each interrupt domain is a tree domain to avoid allocation the 207
entries each time.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This is a cascaded interrupt controller in the AP806 GIC that collapses
SEIs (System Error Interrupt) coming from the AP and the CPs (through
the ICU).
The SEI handles up to 64 interrupts. The first 21 interrupts are wired
from the AP. The next 43 interrupts are from the CPs and are triggered
through MSI messages. To handle this complexity, the driver has to
declare to the upper layer: one IRQ domain for the wired interrupts,
one IRQ domain for the MSIs; and acts as a MSI controller ('parent')
by declaring an MSI domain.
Suggested-by: Haim Boot <hayim@marvell.com>
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ICU can handle several type of interrupt, each of them being handled
differently on AP side. On CP side, the ICU should be able to make the
distinction between each interrupt group by pointing to the right parent.
This is done through the introduction of new bindings, presenting the ICU
node as the parent of multiple ICU sub-nodes, each of them being an
interrupt type with a different interrupt parent. ICU interrupt 'clients'
now directly point to the right sub-node, avoiding the need for the extra
ICU_GRP_* parameter.
ICU subnodes are probed automatically with devm_platform_populate(). If
the node as no child, the probe function for NSRs will still be called
'manually' in order to preserve backward compatibility with DT using the
old binding.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
NSR (non-secure interrupts) are handled in the ICU driver like if there
was only this type of interrupt in the ICU. Change this behavior to
prepare the introduction of SEI (System Error Interrupts) support by
moving the NSR code in a separate function. This is done under the form
of a 'probe' function to ease future migration to NSR/SEI being platform
devices part of the ICU. The 'icu' structure is passed as driver data
and not as a parameter for the same reason.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Rewrite a small section to clarify the reset operation of interrupts
already configured by ATF that we want to handle in the driver. This
will simplify the introduction of System Error Interrupts support.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The irq_domain structure has an host_data pointer that just stores
private data. It is meant to not be touched by the IRQ core. However,
when it comes to MSI, the MSI layer adds its own private data there
with a structure that also has a host_data pointer.
Because this IRQ domain is an MSI domain, to access private data we
should do a d->host_data->host_data, also wrapped as
'platform_msi_get_host_data()'.
This bug was lying there silently because the 'icu' structure retrieved
this way was just called by dev_err(), only producing a
'(NULL device *):' output on the console.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The PDC irqchp can convert a falling edge or level low interrupt to a
rising edge or level high interrupt at the GIC. We just need to setup
the GIC correctly. Set up the interrupt type for the IRQ_TYPE_EDGE_BOTH
as IRQ_TYPE_EDGE_RISING at the GIC.
Fixes: f55c73aef8 ("irqchip/pdc: Add PDC interrupt controller for QCOM SoCs")
Reported-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If the LPI tables have been reserved with the EFI reservation
mechanism, we assume that these tables are safe to use even
when we find the redistributors to have LPIs enabled at
boot time, meaning that kexec can now work with GICv3.
You're welcome.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Upon enabling a redistributor, let's register the allocated tables
with the EFI table that tracks the memory reservations.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If booting with LPIs enabled, all the redistributors must have the
exact same property table. No ifs, no buts.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If using a kdump kernel, and that we cannot disable LPIs to install
our own tables, let's switch to using the already allocated tables.
This means that we'll change some of the initial kernel's memory,
but at least we'll be able to have LPIs in this secondary kernel.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to cope with kexec and GICv3, let's try and spot when
we're booting with LPIs already enabled, and the tables already
programmed into the redistributors.
This code is currently guarded by a predicate that is always false,
meaning this is not functionnal just yet.
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We're currently only tracking the page allocated to contain the
property table by its struct page. In the future, it is going to
be convenient to track both PA and VA for that page instead. Let's
do that.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pending tables for the redistributors are currently allocated
one at a time as each CPU boots. This is causing some grief
for Linux/RT (allocation from within a CPU hotplug notifier is
frown upon).
Let's move this allocation to take place at init time, when we
only have a single CPU. It means we're allocating memory for CPUs
that are not online yet, but most system will boot all of their
CPUs anyway, so that's not completely wasted.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As we're going to reuse some pre-allocated memory for the property
table, split out the zeroing of that table into a separate function
for later use.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
LPI_PENDING_SZ is always used in conjunction with a max(), which doesn't
make much sense, since we're guaranteed that LPI_PENDING_SZ is already
aligned to 64K. Let's remove it.
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
We currently initialize the LPIs (and the ITS) fairly early, even
before the SMP support and the CPU interface. This is a bit odd
(as LPIs are not exactly crutial for the early boot process),
and is going to cause issues when reorganizing the probing code.
Let's move this initialization later.
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Tested-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit fe8e93504c ("irqchip/gic-v3-its: Use full range of LPIs"), removes
the cap for lpi_id_bits, which causes the following warning to trigger on a
QDF2400 server:
WARNING: CPU: 0 PID: 0 at mm/page_alloc.c:4066 __alloc_pages_nodemask
...
Call trace:
__alloc_pages_nodemask+0x2d8/0x1188
alloc_pages_current+0x8c/0xd8
its_allocate_prop_table+0x5c/0xb8
its_init+0x220/0x3c0
gic_init_bases+0x250/0x380
gic_acpi_init+0x16c/0x2a4
In its_alloc_lpi_tables(), lpi_id_bits is 24 in QDF2400. The allocation in
allocate_prop_table() tries therefore to allocate 16M (order 12 if
pagesize=4k), which triggers the warning.
As said by MarcL
Capping lpi_id_bits at 16 (which is what we had before) is plenty,
will save a some memory, and gives some margin before we need to push
it up again.
Bring the upper limit of lpi_id_bits back to prevent
Fixes: fe8e93504c ("irqchip/gic-v3-its: Use full range of LPIs")
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jia He <jia.he@hxt-semitech.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Olof Johansson <olof@lixom.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lkml.kernel.org/r/1535432006-2304-1-git-send-email-jia.he@hxt-semitech.com
Pull irq update from Thomas Gleixner:
"A small set of updats/fixes for the irq subsystem:
- Allow GICv3 interrupts to be configured as wake-up sources to
enable wakeup from suspend
- Make the error handling of the STM32 irqchip init function work
- A set of small cleanups and improvements"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Allow interrupt to be configured as wake-up sources
irqchip/tango: Set irq handler and data in one go
dt-bindings: irqchip: renesas-irqc: Document r8a774a1 support
irqchip/s3c24xx: Remove unneeded comparison of unsigned long to 0
irqchip/stm32: Fix init error handling
irqchip/bcm7038-l1: Hide cpu offline callback when building for !SMP
Var "addr" type incorrect.
It have interrupt controler register address.
Type of void __iomem is correct.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
If an xtensa core provides an additional IRQ controller it should be
treated as a separate piece of hardware and be driven by an irqchip
driver.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Marc Zyngier