When an AUDIT_GET_FEATURE message is sent from userspace to the kernel, it
should reply with a message tagged as an AUDIT_GET_FEATURE type with a struct
audit_feature. The current reply is a message tagged as an AUDIT_GET
type with a struct audit_feature.
This appears to have been a cut-and-paste-eo in commit b0fed40.
Reported-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Report:
Looking at your example code in
http://people.redhat.com/rbriggs/audit-multicast-listen/audit-multicast-listen.c,
it seems that nlmsg_len field in the received messages is supposed to
contain the length of the header + payload, but it is always set to the
size of the header only, i.e. 16. The example program works, because
the printf format specifies the minimum width, not "precision", so it
simply prints out the payload until the first zero byte. This isn't too
much of a problem, but precludes the use of recvmmsg, iiuc?
(gdb) p *(struct nlmsghdr*)nlh
$14 = {nlmsg_len = 16, nlmsg_type = 1100, nlmsg_flags = 0, nlmsg_seq = 0, nlmsg_pid = 9910}
The only time nlmsg_len would have been updated was at audit_buffer_alloc()
inside audit_log_start() and never updated after. It should arguably be done
in audit_log_vformat(), but would be more efficient in audit_log_end().
Reported-by: Zbigniew Jędrzejewski-Szmek <zbyszek@in.waw.pl>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Since there is already a primitive to do this operation in the atomic_t, use it
to simplify audit_serial().
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Use kernel.h definition.
Cc: Eric Paris <eparis@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
This is effectively a revert of 7b9a7ec565
plus fixing it a different way...
We found, when trying to run an application from an application which
had dropped privs that the kernel does security checks on undefined
capability bits. This was ESPECIALLY difficult to debug as those
undefined bits are hidden from /proc/$PID/status.
Consider a root application which drops all capabilities from ALL 4
capability sets. We assume, since the application is going to set
eff/perm/inh from an array that it will clear not only the defined caps
less than CAP_LAST_CAP, but also the higher 28ish bits which are
undefined future capabilities.
The BSET gets cleared differently. Instead it is cleared one bit at a
time. The problem here is that in security/commoncap.c::cap_task_prctl()
we actually check the validity of a capability being read. So any task
which attempts to 'read all things set in bset' followed by 'unset all
things set in bset' will not even attempt to unset the undefined bits
higher than CAP_LAST_CAP.
So the 'parent' will look something like:
CapInh: 0000000000000000
CapPrm: 0000000000000000
CapEff: 0000000000000000
CapBnd: ffffffc000000000
All of this 'should' be fine. Given that these are undefined bits that
aren't supposed to have anything to do with permissions. But they do...
So lets now consider a task which cleared the eff/perm/inh completely
and cleared all of the valid caps in the bset (but not the invalid caps
it couldn't read out of the kernel). We know that this is exactly what
the libcap-ng library does and what the go capabilities library does.
They both leave you in that above situation if you try to clear all of
you capapabilities from all 4 sets. If that root task calls execve()
the child task will pick up all caps not blocked by the bset. The bset
however does not block bits higher than CAP_LAST_CAP. So now the child
task has bits in eff which are not in the parent. These are
'meaningless' undefined bits, but still bits which the parent doesn't
have.
The problem is now in cred_cap_issubset() (or any operation which does a
subset test) as the child, while a subset for valid cap bits, is not a
subset for invalid cap bits! So now we set durring commit creds that
the child is not dumpable. Given it is 'more priv' than its parent. It
also means the parent cannot ptrace the child and other stupidity.
The solution here:
1) stop hiding capability bits in status
This makes debugging easier!
2) stop giving any task undefined capability bits. it's simple, it you
don't put those invalid bits in CAP_FULL_SET you won't get them in init
and you won't get them in any other task either.
This fixes the cap_issubset() tests and resulting fallout (which
made the init task in a docker container untraceable among other
things)
3) mask out undefined bits when sys_capset() is called as it might use
~0, ~0 to denote 'all capabilities' for backward/forward compatibility.
This lets 'capsh --caps="all=eip" -- -c /bin/bash' run.
4) mask out undefined bit when we read a file capability off of disk as
again likely all bits are set in the xattr for forward/backward
compatibility.
This lets 'setcap all+pe /bin/bash; /bin/bash' run
Signed-off-by: Eric Paris <eparis@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Andrew Vagin <avagin@openvz.org>
Cc: Andrew G. Morgan <morgan@kernel.org>
Cc: Serge E. Hallyn <serge.hallyn@canonical.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Steve Grubb <sgrubb@redhat.com>
Cc: Dan Walsh <dwalsh@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Morris <james.l.morris@oracle.com>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
Use #include <linux/types.h> instead of <asm/types.h>
Signed-off-by: Paul McQuade <paulmcquad@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible by passing a netlink socket to a more privileged
executable and then to fool that executable into writing to the socket
data that happens to be valid netlink message to do something that
privileged executable did not intend to do.
To keep this from happening replace bare capable and ns_capable calls
with netlink_capable, netlink_net_calls and netlink_ns_capable calls.
Which act the same as the previous calls except they verify that the
opener of the socket had the desired permissions as well.
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test first to see if there are any userspace multicast listeners bound to the
socket before starting the multicast send work.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a netlink multicast socket with one group to kaudit for "best-effort"
delivery to read-only userspace clients such as systemd, in addition to the
existing bidirectional unicast auditd userspace client.
Currently, auditd is intended to use the CAP_AUDIT_CONTROL and CAP_AUDIT_WRITE
capabilities, but actually uses CAP_NET_ADMIN. The CAP_AUDIT_READ capability
is added for use by read-only AUDIT_NLGRP_READLOG netlink multicast group
clients to the kaudit subsystem.
This will safely give access to services such as systemd to consume audit logs
while ensuring write access remains restricted for integrity.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register a netlink per-protocol bind fuction for audit to check userspace
process capabilities before allowing a multicast group connection.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull audit updates from Eric Paris.
* git://git.infradead.org/users/eparis/audit: (28 commits)
AUDIT: make audit_is_compat depend on CONFIG_AUDIT_COMPAT_GENERIC
audit: renumber AUDIT_FEATURE_CHANGE into the 1300 range
audit: do not cast audit_rule_data pointers pointlesly
AUDIT: Allow login in non-init namespaces
audit: define audit_is_compat in kernel internal header
kernel: Use RCU_INIT_POINTER(x, NULL) in audit.c
sched: declare pid_alive as inline
audit: use uapi/linux/audit.h for AUDIT_ARCH declarations
syscall_get_arch: remove useless function arguments
audit: remove stray newline from audit_log_execve_info() audit_panic() call
audit: remove stray newlines from audit_log_lost messages
audit: include subject in login records
audit: remove superfluous new- prefix in AUDIT_LOGIN messages
audit: allow user processes to log from another PID namespace
audit: anchor all pid references in the initial pid namespace
audit: convert PPIDs to the inital PID namespace.
pid: get pid_t ppid of task in init_pid_ns
audit: rename the misleading audit_get_context() to audit_take_context()
audit: Add generic compat syscall support
audit: Add CONFIG_HAVE_ARCH_AUDITSYSCALL
...
It its possible to configure your PAM stack to refuse login if audit
messages (about the login) were unable to be sent. This is common in
many distros and thus normal configuration of many containers. The PAM
modules determine if audit is enabled/disabled in the kernel based on
the return value from sending an audit message on the netlink socket.
If userspace gets back ECONNREFUSED it believes audit is disabled in the
kernel. If it gets any other error else it refuses to let the login
proceed.
Just about ever since the introduction of namespaces the kernel audit
subsystem has returned EPERM if the task sending a message was not in
the init user or pid namespace. So many forms of containers have never
worked if audit was enabled in the kernel.
BUT if the container was not in net_init then the kernel network code
would send ECONNREFUSED (instead of the audit code sending EPERM). Thus
by pure accident/dumb luck/bug if an admin configured the PAM stack to
reject all logins that didn't talk to audit, but then ran the login
untility in the non-init_net namespace, it would work!! Clearly this was
a bug, but it is a bug some people expected.
With the introduction of network namespace support in 3.14-rc1 the two
bugs stopped cancelling each other out. Now, containers in the
non-init_net namespace refused to let users log in (just like PAM was
configfured!) Obviously some people were not happy that what used to let
users log in, now didn't!
This fix is kinda hacky. We return ECONNREFUSED for all non-init
relevant namespaces. That means that not only will the old broken
non-init_net setups continue to work, now the broken non-init_pid or
non-init_user setups will 'work'. They don't really work, since audit
isn't logging things. But it's what most users want.
In 3.15 we should have patches to support not only the non-init_net
(3.14) namespace but also the non-init_pid and non-init_user namespace.
So all will be right in the world. This just opens the doors wide open
on 3.14 and hopefully makes users happy, if not the audit system...
Reported-by: Andre Tomt <andre@tomt.net>
Reported-by: Adam Richter <adam_richter2004@yahoo.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
kernel/audit.c
It its possible to configure your PAM stack to refuse login if audit
messages (about the login) were unable to be sent. This is common in
many distros and thus normal configuration of many containers. The PAM
modules determine if audit is enabled/disabled in the kernel based on
the return value from sending an audit message on the netlink socket.
If userspace gets back ECONNREFUSED it believes audit is disabled in the
kernel. If it gets any other error else it refuses to let the login
proceed.
Just about ever since the introduction of namespaces the kernel audit
subsystem has returned EPERM if the task sending a message was not in
the init user or pid namespace. So many forms of containers have never
worked if audit was enabled in the kernel.
BUT if the container was not in net_init then the kernel network code
would send ECONNREFUSED (instead of the audit code sending EPERM). Thus
by pure accident/dumb luck/bug if an admin configured the PAM stack to
reject all logins that didn't talk to audit, but then ran the login
untility in the non-init_net namespace, it would work!! Clearly this was
a bug, but it is a bug some people expected.
With the introduction of network namespace support in 3.14-rc1 the two
bugs stopped cancelling each other out. Now, containers in the
non-init_net namespace refused to let users log in (just like PAM was
configfured!) Obviously some people were not happy that what used to let
users log in, now didn't!
This fix is kinda hacky. We return ECONNREFUSED for all non-init
relevant namespaces. That means that not only will the old broken
non-init_net setups continue to work, now the broken non-init_pid or
non-init_user setups will 'work'. They don't really work, since audit
isn't logging things. But it's what most users want.
In 3.15 we should have patches to support not only the non-init_net
(3.14) namespace but also the non-init_pid and non-init_user namespace.
So all will be right in the world. This just opens the doors wide open
on 3.14 and hopefully makes users happy, if not the audit system...
Reported-by: Andre Tomt <andre@tomt.net>
Reported-by: Adam Richter <adam_richter2004@yahoo.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces rcu_assign_pointer(x, NULL) with RCU_INIT_POINTER(x, NULL)
The rcu_assign_pointer() ensures that the initialization of a structure
is carried out before storing a pointer to that structure.
And in the case of the NULL pointer, there is no structure to initialize.
So, rcu_assign_pointer(p, NULL) can be safely converted to RCU_INIT_POINTER(p, NULL)
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Calling audit_log_lost with a \n in the format string leads to extra
newlines in dmesg. That function will eventually call audit_panic which
uses pr_err with an explicit \n included. Just make these calls match the
others that lack \n.
Reported-by: Jonathan Kamens <jik@kamens.brookline.ma.us>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Still only permit the audit logging daemon and control to operate from the
initial PID namespace, but allow processes to log from another PID namespace.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
(informed by ebiederman's c776b5d2)
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Store and log all PIDs with reference to the initial PID namespace and
use the access functions task_pid_nr() and task_tgid_nr() for task->pid
and task->tgid.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
(informed by ebiederman's c776b5d2)
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
sys_getppid() returns the parent pid of the current process in its own pid
namespace. Since audit filters are based in the init pid namespace, a process
could avoid a filter or trigger an unintended one by being in an alternate pid
namespace or log meaningless information.
Switch to task_ppid_nr() for PPIDs to anchor all audit filters in the
init_pid_ns.
(informed by ebiederman's 6c621b7e)
Cc: stable@vger.kernel.org
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
In perverse cases of file descriptor passing the current network
namespace of a process and the network namespace of a socket used by
that socket may differ. Therefore use the network namespace of the
appropiate socket to ensure replies always go to the appropiate
socket.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
While reading through 3.14-rc1 I found a pretty siginficant mishandling
of network namespaces in the recent audit changes.
In struct audit_netlink_list and audit_reply add a reference to the
network namespace of the caller and remove the userspace pid of the
caller. This cleanly remembers the callers network namespace, and
removes a huge class of races and nasty failure modes that can occur
when attempting to relook up the callers network namespace from a pid_t
(including the caller's network namespace changing, pid wraparound, and
the pid simply not being present).
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
The kbuild test robot reported:
> tree: git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace.git for-next
> head: 6f285b19d0
> commit: 6f285b19d0 [2/2] audit: Send replies in the proper network namespace.
> reproduce: make htmldocs
>
> >> Warning(kernel/audit.c:575): No description found for parameter 'request_skb'
> >> Warning(kernel/audit.c:575): Excess function parameter 'portid' description in 'audit_send_reply'
> >> Warning(kernel/auditfilter.c:1074): No description found for parameter 'request_skb'
> >> Warning(kernel/auditfilter.c:1074): Excess function parameter 'portid' description in 'audit_list_rules_s
Which was caused by my failure to update the kdoc annotations when I
updated the functions. Fix that small oversight now.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
In perverse cases of file descriptor passing the current network
namespace of a process and the network namespace of a socket used by
that socket may differ. Therefore use the network namespace of the
appropiate socket to ensure replies always go to the appropiate
socket.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
In struct audit_netlink_list and audit_reply add a reference to the
network namespace of the caller and remove the userspace pid of the
caller. This cleanly remembers the callers network namespace, and
removes a huge class of races and nasty failure modes that can occur
when attempting to relook up the callers network namespace from a
pid_t (including the caller's network namespace changing, pid
wraparound, and the pid simply not being present).
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
A message about creating the audit socket might be fine at startup, but
a pr_info for every single network namespace created on a system isn't
useful.
Signed-off-by: Eric Paris <eparis@redhat.com>
The equivalent uapi struct uses __u32 so make the kernel
uses u32 too.
This can prevent some oddities where the limit is
logged/emitted as a negative value.
Convert kstrtol to kstrtouint to disallow negative values.
Signed-off-by: Joe Perches <joe@perches.com>
[eparis: do not remove static from audit_default declaration]
Add pr_fmt to prefix "audit: " to output
Convert printk(KERN_<LEVEL> to pr_<level>
Coalesce formats
Use pr_cont
Move a brace after switch
Signed-off-by: Joe Perches <joe@perches.com>
Using the generic kernel function causes the
object size to increase with gcc 4.8.1.
$ size kernel/audit.o*
text data bss dec hex filename
18577 6079 8436 33092 8144 kernel/audit.o.new
18579 6015 8420 33014 80f6 kernel/audit.o.old
Unsigned...
An admin is likely to want to see old and new values next to each other.
Putting all of the old values followed by all of the new values is just
hard to read as a human.
Signed-off-by: Eric Paris <eparis@redhat.com>
We can simplify the AUDIT_TTY_SET code to only grab the spin_lock one
time. We need to determine if the new values are valid and if so, set
the new values at the same time we grab the old onces. While we are
here get rid of 'res' and just use err.
Signed-off-by: Eric Paris <eparis@redhat.com>
If userspace specified that it was setting values via the mask we do not
need a second check to see if they also set the version field high
enough to understand those values. (clearly if they set the mask they
knew those values).
Signed-off-by: Eric Paris <eparis@redhat.com>
Give names to the audit versions. Just something for a userspace
programmer to know what the version provides.
Signed-off-by: Eric Paris <eparis@redhat.com>
We had some craziness with signed to unsigned long casting which appears
wholely unnecessary. Just use signed long. Even though 2 values of the
math equation are unsigned longs the result is expected to be a signed
long. So why keep casting the result to signed long? Just make it
signed long and use it.
We also remove the needless "timeout" variable. We already have the
stack "sleep_time" variable. Just use that...
Signed-off-by: Eric Paris <eparis@redhat.com>
NETLINK_CB(skb).sk is the socket of user space process,
netlink_unicast in kauditd_send_skb wants the kernel
side socket. Since the sk_state of audit netlink socket
is not NETLINK_CONNECTED, so the netlink_getsockbyportid
doesn't return -ECONNREFUSED.
And the socket of userspace process can be released anytime,
so the audit_sock may point to invalid socket.
this patch sets the audit_sock to the kernel side audit
netlink socket.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
print the error message and then return -ENOMEM.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
An error on an AUDIT_NEVER rule disabled logging on that rule.
On error on AUDIT_NEVER rules, log.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
The backlog cannot be consumed when audit_log_start is running on auditd
even if audit_log_start calls wait_for_auditd to consume it.
The situation is the deadlock because only auditd can consume the backlog.
If the other process needs to send the backlog, it can be also stopped
by the deadlock.
So, audit_log_start running on auditd should not stop.
You can see the deadlock with the following reproducer:
# auditctl -a exit,always -S all
# reboot
Signed-off-by: Toshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Reviewed-by: gaofeng@cn.fujitsu.com
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
We do not need to hold the audit_cmd_mutex for this family of cases. The
possible exception to this is the call to audit_filter_user(), so drop the lock
immediately after. To help in fixing the race we are trying to avoid, make
sure that nothing called by audit_filter_user() calls audit_log_start(). In
particular, watch out for *_audit_rule_match().
This fix will take care of systemd and anything USING audit. It still means
that we could race with something configuring audit and auditd shutting down.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Reported-by: toshi.okajima@jp.fujitsu.com
Tested-by: toshi.okajima@jp.fujitsu.com
Signed-off-by: Eric Paris <eparis@redhat.com>
Right now the sessionid value in the kernel is a combination of u32,
int, and unsigned int. Just use unsigned int throughout.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Currently when the coredump signals are logged by the audit system, the
actual path to the executable is not logged. Without details of exe, the
system admin may not have an exact idea on what program failed.
This patch changes the audit_log_task() so that the path to the exe is also
logged.
This was copied from audit_log_task_info() and the latter enhanced to avoid
disappearing text fields.
Signed-off-by: Paul Davies C <pauldaviesc@gmail.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
There have been reports of auditd restarts resulting in kaudit not being able
to find a newly registered auditd. It results in reports such as:
kernel: [ 2077.233573] audit: *NO* daemon at audit_pid=1614
kernel: [ 2077.234712] audit: audit_lost=97 audit_rate_limit=0 audit_backlog_limit=320
kernel: [ 2077.234718] audit: auditd disappeared
(previously mis-spelled "dissapeared")
One possible cause is a race between the shutdown of an older auditd and a
newer one. If the newer one sets the daemon pid to itself in kauditd before
the older one has cleared the daemon pid, the newer daemon pid will be erased.
This could be caused by an automated system, or by manual intervention, but in
either case, there is no use in having the older daemon clear the daemon pid
reference since its old pid is no longer being referenced. This patch will
prevent that specific case, returning an error of EACCES.
The case for preventing a newer auditd from registering itself if there is an
existing auditd is a more difficult case that is beyond the scope of this
patch.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
audit_receive_msg() needlessly contained a fallthrough case that called
audit_receive_filter(), containing no common code between the cases. Separate
them to make the logic clearer. Refactor AUDIT_LIST_RULES, AUDIT_ADD_RULE,
AUDIT_DEL_RULE cases to create audit_rule_change(), audit_list_rules_send()
functions. This should not functionally change the logic.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Log transition of config changes when AUDIT_TTY_SET is called, including both
enabled and log_passwd values now in the struct.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
kauditd_send_skb is called after audit_pid was checked to be non-zero.
However, it can be set to 0 due to auditd exiting while kauditd_send_skb
is still executed and this can result in a spurious warning about missing
auditd.
Re-check audit_pid before printing the message.
Signed-off-by: Mateusz Guzik <mguzik@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Since audit can already be disabled by "audit=0" on the kernel boot line, or by
the command "auditctl -e 0", it would be more useful to have the
audit_backlog_limit set to zero mean effectively unlimited (limited only by
system RAM).
Acked-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
we already have old_lock, no need to calculate it again.
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
If audit is disabled,we shouldn't generate the audit log.
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
The order of new feature and old feature is incorrect,
this patch fix it.
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Since kernel parameter is operated before
initcall, so the audit_initialized must be
AUDIT_UNINITIALIZED or DISABLED in audit_enable.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
reaahead-collector abuses the audit logging facility to discover which files
are accessed at boot time to make a pre-load list
Add a tuning option to audit_backlog_wait_time so that if auditd can't keep up,
or gets blocked, the callers won't be blocked.
Bump audit_status API version to "2".
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Re-named confusing local variable names (status_set and status_get didn't agree
with their command type name) and reduced their scope.
Future-proof API changes by not depending on the exact size of the audit_status
struct and by adding an API version field.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
The default audit_backlog_limit is 64. This was a reasonable limit at one time.
systemd causes so much audit queue activity on startup that auditd doesn't
start before the backlog queue has already overflowed by more than a factor of
2. On a system with audit= not set on the kernel command line, this isn't an
issue since that history isn't kept for auditd when it is available. On a
system with audit=1 set on the kernel command line, kaudit tries to keep that
history until auditd is able to drain the queue.
This default can be changed by the "-b" option in audit.rules once the system
has booted, but won't help with lost messages on boot.
One way to solve this would be to increase the default backlog queue size to
avoid losing any messages before auditd is able to consume them. This would
be overkill to the embedded community and insufficient for some servers.
Another way to solve it might be to add a kconfig option to set the default
based on the system type. An embedded system would get the current (or
smaller) default, while Workstations might get more than now and servers might
get more.
None of these solutions helps if a system's compiled default is too small to
see the lost messages without compiling a new kernel.
This patch adds a kernel set-up parameter (audit already has one to
enable/disable it) "audit_backlog_limit=<n>" that overrides the default to
allow the system administrator to set the backlog limit.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
These and similar errors were seen on a patched 3.8 kernel when the
audit subsystem was overrun during boot:
udevd[876]: worker [887] unexpectedly returned with status 0x0100
udevd[876]: worker [887] failed while handling
'/devices/pci0000:00/0000:00:03.0/0000:40:00.0'
udevd[876]: worker [880] unexpectedly returned with status 0x0100
udevd[876]: worker [880] failed while handling
'/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1/event1'
udevadm settle - timeout of 180 seconds reached, the event queue
contains:
/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1/event1 (3995)
/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/INT3F0D:00 (4034)
audit: audit_backlog=258 > audit_backlog_limit=256
audit: audit_lost=1 audit_rate_limit=0 audit_backlog_limit=256
The change below increases the efficiency of the audit code and prevents it
from being overrun:
Use add_wait_queue_exclusive() in wait_for_auditd() to put the
thread on the wait queue. When kauditd dequeues an skb, all
of the waiting threads are waiting for the same resource, but
only one is going to get it, so there's no need to wake up
more than one waiter.
See: https://lkml.org/lkml/2013/9/2/479
Signed-off-by: Dan Duval <dan.duval@oracle.com>
Signed-off-by: Chuck Anderson <chuck.anderson@oracle.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
These and similar errors were seen on a patched 3.8 kernel when the
audit subsystem was overrun during boot:
udevd[876]: worker [887] unexpectedly returned with status 0x0100
udevd[876]: worker [887] failed while handling
'/devices/pci0000:00/0000:00:03.0/0000:40:00.0'
udevd[876]: worker [880] unexpectedly returned with status 0x0100
udevd[876]: worker [880] failed while handling
'/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1/event1'
udevadm settle - timeout of 180 seconds reached, the event queue
contains:
/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1/event1 (3995)
/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/INT3F0D:00 (4034)
audit: audit_backlog=258 > audit_backlog_limit=256
audit: audit_lost=1 audit_rate_limit=0 audit_backlog_limit=256
The change below increases the efficiency of the audit code and prevents it
from being overrun:
Only issue a wake_up in kauditd if the length of the skb queue is less than the
backlog limit. Otherwise, threads waiting in wait_for_auditd() will simply
wake up, discover that the queue is still too long for them to proceed, and go
back to sleep. This results in wasted context switches and machine cycles.
kauditd_thread() is the only function that removes buffers from audit_skb_queue
so we can't race. If we did, the timeout in wait_for_auditd() would expire and
the waiting thread would continue.
See: https://lkml.org/lkml/2013/9/2/479
Signed-off-by: Dan Duval <dan.duval@oracle.com>
Signed-off-by: Chuck Anderson <chuck.anderson@oracle.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
If wait_for_auditd() times out, go immediately to the error function rather
than retesting the loop conditions.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
When the audit queue overflows and times out (audit_backlog_wait_time), the
audit queue overflow timeout is set to zero. Once the audit queue overflow
timeout condition recovers, the timeout should be reset to the original value.
See also:
https://lkml.org/lkml/2013/9/2/473
Cc: stable@vger.kernel.org # v3.8-rc4+
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Dan Duval <dan.duval@oracle.com>
Signed-off-by: Chuck Anderson <chuck.anderson@oracle.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Convert audit from only listening in init_net to use register_pernet_subsys()
to dynamically manage the netlink socket list.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
When being refactored from audit_log_start() to audit_log_task_info(), in
commit e23eb920 the tty and ses fields in the log output got transposed.
Restore to original order to avoid breaking search tools.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Normally, netlink ports use the PID of the userspace process as the port ID.
If the PID is already in use by a port, the kernel will allocate another port
ID to avoid conflict. Re-name all references to netlink ports from pid to
portid to reflect this reality and avoid confusion with actual PIDs. Ports
use the __u32 type, so re-type all portids accordingly.
(This patch is very similar to ebiederman's 5deadd69)
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
...to make it clear what the intent behind each record's operation was.
In many cases you can infer this, based on the context of the syscall
and the result. In other cases it's not so obvious. For instance, in
the case where you have a file being renamed over another, you'll have
two different records with the same filename but different inode info.
By logging this information we can clearly tell which one was created
and which was deleted.
This fixes what was broken in commit bfcec708.
Commit 79f6530c should also be backported to stable v3.7+.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
In send/GET, we don't want the kernel to lie about what value is set.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Using the nlmsg_len member of the netlink header to test if the message
is valid is wrong as it includes the size of the netlink header itself.
Thereby allowing to send short netlink messages that pass those checks.
Use nlmsg_len() instead to test for the right message length. The result
of nlmsg_len() is guaranteed to be non-negative as the netlink message
already passed the checks of nlmsg_ok().
Also switch to min_t() to please checkpatch.pl.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Paris <eparis@redhat.com>
Cc: stable@vger.kernel.org # v2.6.6+ for the 1st hunk, v2.6.23+ for the 2nd
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
We currently are setting fields to 0 to initialize the structure
declared on the stack. This is a bad idea as if the structure has holes
or unpacked space these will not be initialized. Just use memset. This
is not a performance critical section of code.
Signed-off-by: Eric Paris <eparis@redhat.com>
We leak 4 bytes of kernel stack in response to an AUDIT_GET request as
we miss to initialize the mask member of status_set. Fix that.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Paris <eparis@redhat.com>
Cc: stable@vger.kernel.org # v2.6.6+
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
This adds a new 'audit_feature' bit which allows userspace to set it
such that the loginuid is absolutely immutable, even if you have
CAP_AUDIT_CONTROL.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
This is a new audit feature which only grants processes with
CAP_AUDIT_CONTROL the ability to unset their loginuid. They cannot
directly set it from a valid uid to another valid uid. The ability to
unset the loginuid is nice because a priviledged task, like that of
container creation, can unset the loginuid and then priv is not needed
inside the container when a login daemon needs to set the loginuid.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
The audit_status structure was not designed with extensibility in mind.
Define a new AUDIT_SET_FEATURE message type which takes a new structure
of bits where things can be enabled/disabled/locked one at a time. This
structure should be able to grow in the future while maintaining forward
and backward compatibility (based loosly on the ideas from capabilities
and prctl)
This does not actually add any features, but is just infrastructure to
allow new on/off types of audit system features.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
When the audit=1 kernel parameter is absent and auditd is not running,
AUDIT_USER_AVC messages are being silently discarded.
AUDIT_USER_AVC messages should be sent to userspace using printk(), as
mentioned in the commit message of 4a4cd633 ("AUDIT: Optimise the
audit-disabled case for discarding user messages").
When audit_enabled is 0, audit_receive_msg() discards all user messages
except for AUDIT_USER_AVC messages. However, audit_log_common_recv_msg()
refuses to allocate an audit_buffer if audit_enabled is 0. The fix is to
special case AUDIT_USER_AVC messages in both functions.
It looks like commit 50397bd1 ("[AUDIT] clean up audit_receive_msg()")
introduced this bug.
Cc: <stable@kernel.org> # v2.6.25+
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Paris <eparis@redhat.com>
Cc: linux-audit@redhat.com
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Remove it.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
A newline was accidentally added during session ID helper refactorization in
commit 4d3fb709. This needlessly uses up buffer space, messes up syslog
formatting and makes userspace processing less efficient. Remove it.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Ilya V. Matveychikov <matvejchikov@gmail.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Messages of type AUDIT_USER_TTY were being formatted to 1024 octets,
truncating messages approaching MAX_AUDIT_MESSAGE_LENGTH (8970 octets).
Set the formatting to 8560 characters, given maximum estimates for prefix and
suffix budgets.
See the problem discussion:
https://www.redhat.com/archives/linux-audit/2009-January/msg00030.html
And the new size rationale:
https://www.redhat.com/archives/linux-audit/2013-September/msg00016.html
Test ~8k messages with:
auditctl -m "$(for i in $(seq -w 001 820);do echo -n "${i}0______";done)"
Reported-by: LC Bruzenak <lenny@magitekltd.com>
Reported-by: Justin Stephenson <jstephen@redhat.com>
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
After commit 829199197a ("kernel/audit.c: avoid negative sleep
durations") audit emitters will block forever if userspace daemon cannot
handle backlog.
After the timeout the waiting loop turns into busy loop and runs until
daemon dies or returns back to work. This is a minimal patch for that
bug.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Richard Guy Briggs <rgb@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Chuck Anderson <chuck.anderson@oracle.com>
Cc: Dan Duval <dan.duval@oracle.com>
Cc: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
audit_log_start() does wait_for_auditd() in a loop until
audit_backlog_wait_time passes or audit_skb_queue has a room.
If signal_pending() is true this becomes a busy-wait loop, schedule() in
TASK_INTERRUPTIBLE won't block.
Thanks to Guy for fully investigating and explaining the problem.
(akpm: that'll cause the system to lock up on a non-preemptible
uniprocessor kernel)
(Guy: "Our customer was in fact running a uniprocessor machine, and they
reported a system hang.")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Guy Streeter <streeter@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull audit changes from Eric Paris:
"Al used to send pull requests every couple of years but he told me to
just start pushing them to you directly.
Our touching outside of core audit code is pretty straight forward. A
couple of interface changes which hit net/. A simple argument bug
calling audit functions in namei.c and the removal of some assembly
branch prediction code on ppc"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: fix message spacing printing auid
Revert "audit: move kaudit thread start from auditd registration to kaudit init"
audit: vfs: fix audit_inode call in O_CREAT case of do_last
audit: Make testing for a valid loginuid explicit.
audit: fix event coverage of AUDIT_ANOM_LINK
audit: use spin_lock in audit_receive_msg to process tty logging
audit: do not needlessly take a lock in tty_audit_exit
audit: do not needlessly take a spinlock in copy_signal
audit: add an option to control logging of passwords with pam_tty_audit
audit: use spin_lock_irqsave/restore in audit tty code
helper for some session id stuff
audit: use a consistent audit helper to log lsm information
audit: push loginuid and sessionid processing down
audit: stop pushing loginid, uid, sessionid as arguments
audit: remove the old depricated kernel interface
audit: make validity checking generic
audit: allow checking the type of audit message in the user filter
audit: fix build break when AUDIT_DEBUG == 2
audit: remove duplicate export of audit_enabled
Audit: do not print error when LSMs disabled
...
The helper function didn't include a leading space, so it was jammed
against the previous text in the audit record.
Signed-off-by: Eric Paris <eparis@redhat.com>
This reverts commit 6ff5e45985.
Conflicts:
kernel/audit.c
This patch was starting a kthread for all the time. Since the follow on
patches that required it didn't get finished in 3.10 time, we shouldn't
ship this change in 3.10.
Signed-off-by: Eric Paris <eparis@redhat.com>
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
The userspace audit tools didn't like the existing formatting of the
AUDIT_ANOM_LINK event. It needed to be expanded to emit an AUDIT_PATH
event as well, so this implements the change. The bulk of the patch is
moving code out of auditsc.c into audit.c and audit.h for general use.
It expands audit_log_name to include an optional "struct path" argument
for the simple case of just needing to report a pathname. This also
makes
audit_log_task_info available when syscall auditing is not enabled,
since
it is needed in either case for process details.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Steve Grubb <sgrubb@redhat.com>
This function is called when we receive a netlink message from
userspace. We don't need to worry about it coming from irq context or
irqs making it re-entrant.
Signed-off-by: Eric Paris <eparis@redhat.com>
Most commands are entered one line at a time and processed as complete lines
in non-canonical mode. Commands that interactively require a password, enter
canonical mode to do this while shutting off echo. This pair of features
(icanon and !echo) can be used to avoid logging passwords by audit while still
logging the rest of the command.
Adding a member (log_passwd) to the struct audit_tty_status passed in by
pam_tty_audit allows control of canonical mode without echo per task.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Some of the callers of the audit tty function use spin_lock_irqsave/restore.
We were using the forced always enable version, which seems really bad.
Since I don't know every one of these code paths well enough, it makes
sense to just switch everything to the safe version. Maybe it's a
little overzealous, but it's a lot better than an unlucky deadlock when
we return to a caller with irq enabled and they expect it to be
disabled.
Signed-off-by: Eric Paris <eparis@redhat.com>
We have a number of places we were reimplementing the same code to write
out lsm labels. Just do it one darn place.
Signed-off-by: Eric Paris <eparis@redhat.com>
Since we are always current, we can push a lot of this stuff to the
bottom and get rid of useless interfaces and arguments.
Signed-off-by: Eric Paris <eparis@redhat.com>
We always use current. Stop pulling this when the skb comes in and
pushing it around as arguments. Just get it at the end when you need
it.
Signed-off-by: Eric Paris <eparis@redhat.com>
We used to have an inflexible mechanism to add audit rules to the
kernel. It hasn't been used in a long time. Get rid of that stuff.
Signed-off-by: Eric Paris <eparis@redhat.com>
We only need to check if kauditd is valid after we start it, if kauditd
is invalid, we will set kauditd_task to NULL. So next time, we will
start kauditd again.
It means if kauditd_task is not NULL,it must be valid.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When userspace sends messages to the audit system it includes a type.
We want to be able to filter messages based on that type without have to
do the all or nothing option currently available on the
AUDIT_FILTER_TYPE filter list. Instead we should be able to use the
AUDIT_FILTER_USER filter list and just use the message type as one part
of the matching decision.
Signed-off-by: Eric Paris <eparis@redhat.com>
Userspace parsing libraries assume that msg= is only for userspace audit
records, not for user tty records. Make this consistent with the other
tty records.
Reported-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
The kauditd_thread() task was started only after the auditd userspace daemon
registers itself with kaudit. This was fine when only auditd consumed messages
from the kaudit netlink unicast socket. With the addition of a multicast group
to that socket it is more convenient to have the thread start on init of the
kaudit kernel subsystem.
Signed-off-by: Richard Guy Briggs <rbriggs@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
The wait queue control code in kauditd_thread() was nested deeper than
necessary. The function has been flattened for better legibility.
Signed-off-by: Richard Guy Briggs <rbriggs@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
The hold queue flush code is an autonomous chunk of code that can be
refactored, removed from kauditd_thread() into flush_hold_queue() and
flattenned for better legibility.
Signed-off-by: Richard Guy Briggs <rbriggs@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Commit 9419121330 replaced the macros
NLMSG_NEXT with calls to nlmsg_next which produces this warning:
kernel/audit.c: In function ‘audit_receive_skb’:
kernel/audit.c:928:3: warning: passing argument 2 of ‘nlmsg_next’ makes pointer from integer without a cast
In file included from include/net/rtnetlink.h:5:0,
from include/net/neighbour.h:28,
from include/net/dst.h:17,
from include/net/sock.h:68,
from kernel/audit.c:55:
include/net/netlink.h:359:1: note: expected ‘int *’ but argument is of type ‘int’
Fix this by sending the intended pointer.
Signed-off-by: Alexandru Copot <alex.mihai.c@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Guy Briggs