The newly introduced soc_pcmcia_regulator_set() function sometimes
returns without setting its return code, as shown by this warning:
drivers/pcmcia/soc_common.c: In function 'soc_pcmcia_regulator_set':
drivers/pcmcia/soc_common.c:112:5: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This changes it to propagate the regulator_disable() result instead.
Fixes: ac61b6001a ("pcmcia: soc_common: add support for Vcc and Vpp regulators")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Constify the pcmcia_low_level operation pointer to soc_pcmcia_init_one()
which has no need to modify it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Switch to a per-socket cpufreq notifier rather than a global notifier.
This allows each socket to be self-contained.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Add support for handling supply regulators in the soc_common code. This
allows us to separate out the board specifics for setting voltages from
the PCMCIA code.
We detect when setting a voltage fails, and report this fact - some
platforms have fixed-voltage supplies (eg, for CF sockets at 3.3V) and
we need to ignore attempts to configure for 5V, as per the existing
board specific drivers.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Add a helper to get the voltage state of CF sockets, where the voltage
sense pins are not wired up. Switch assabet and cerf to use this
helper.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
If an attempt to set a socket state returns an error, restore the
previous socket state. If restoring the previous socket state
fails, warn about this.
This allows us to have simple error handling in the socket state
configuration handlers - there is no need for every handler
implementation to manually undo the updates, which can be complex
when regulators are involved.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Add support to soc_common for controlling reset and bus enable GPIOs
from within the generic soc_common layer, rather than having
individual drivers having to perform this themselves.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Request the legacy card detect signal with the active low property and
remove our own negation of the detection value. This allows us to use
the firmware-defined polarities rather than hard-coding it into the
driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
If gpiod_to_irq() returns an invalid interrupt, we should not try to use
it as an interrupt number.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Use devm_gpio_request_one() to request the GPIOs so we can avoid
manual clean up these gpio resources.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This patch introduces the use of function setup_timer.
This is done using Coccinelle and semantic patch used is
as follows:
@@
expression x,y,z;
@@
- init_timer (&x);
+ setup_timer (&x, y, z);
- x.function = y;
- x.data = z;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call clk_prepare_enable() during hw_init() and clk_disable_unprepare()
during hw_shutdown() to ensure that the clock rates returned by
clk_get_rate() are correct.
It is safe to call enable/disable functions even on NULL clock, so this
patch will not break cases when the socket clock is not set.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Now that we use gpios and gpio_to_irq() etc to manage the various card
status signals within soc_common, and all socket drivers are converted,
these functions are no longer used. We can now get rid of these helper
functions.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add GPIO support for reading the card status (card detect, ready,
battery voltage detect) signals into soc_common code. As we want
interrupts from these GPIOs, this takes over the old irq handling
infrastructure for card status signals, which will now be managed
entirely by the soc_common code.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move common socket initialization into soc_common.c.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
10 boards define these empty, probably indicating not everyone has a use for them.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch fixes checkpatch.pl issues in drivers/pcmcia/soc_common.c.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a compilation issue when compiling PCMCIA SA1100
support as a module with PCMCIA_DEBUG enabled. The symbol
soc_pcmcia_debug was not beeing exported.
ARM: pcmcia: Fix for building DEBUG with sa11xx_base.c as a module.
This patch fixes a compilation issue when compiling PCMCIA SA1100
support as a module with PCMCIA_DEBUG enabled. The symbol
soc_pcmcia_debug was not beeing exported.
Cc: <stable@kernel.org>
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Using %pV reduces the number of printk calls and
eliminates any possible message interleaving from
other printk calls.
Signed-off-by: Joe Perches <joe@perches.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Eric Miao <eric.y.miao@gmail.com>
CC: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
au100_generic and soc_common call flush_scheduled_work() spuriously.
Remove them.
This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
skt->irq is a mere duplication of pcmcia_socket's pci_irq member.
Get rid of it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Move the individual socket probing and initialization down into the
SoC specific support files, thereby allowing soc_common_drv_pcmcia_probe
to be eliminated. soc_common.c now no longer deals with distinct groups
of sockets.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Mechanically transplant the removal code from soc_common into each
SoC specific base support file, thereby allowing
soc_common_drv_pcmcia_remove to be removed. No other changes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Factor out the functionality for adding and removing a single
socket, thereby allowing SoCs to individually register each
socket. The advantage of this approach is that SoCs can then
extend soc_pcmcia_socket as they wish.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Convert soc_common.c to be a stand alone module, rather than wrapping
it up into the individual SoC specific base modules. In doing this,
we need to add init/exit functions for soc_common to register/remove
the cpufreq notifier.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Fix more possible warnings introduced by my commit
1d80766554 as fixed by the previous patch from
Randy Dunlap. Not tested due to no hardware.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Move the processor specific initialization (largely resources initialization)
out of soc_common_drv_pcmcia_probe() into dedicated sa11xx_drv_pcmcia_probe()
and __pxa2xx_drv_pcmcia_probe().
By doing this, we are now able to move the PCMCIA related definitions out of
pxa-regs.h and back into pxa2xx_base.c.
As a result, remove that reference of _PCMCIA1IO in arch/arm/mach-pxa/viper.c.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Fix warning when compiling "drivers/pcmcia/soc-common.c"
The return value of the function "device_create_file"
was not used / assigned.
Signed-off-by: Jrgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use CONFIG_PCMCIA_DEBUG instead of DEBUG so that dev_dbg() and other tricks
work properly.
(includes bugfixes from and
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
)
Signed-off-by: Dominik Broodwski <linux@dominikbrodowski.net>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:
s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As found on some arm defconfigs.
I only looked at how original patch changes things and other patches fix
compilation. ;-)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Cc: <linux-pcmcia@lists.infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Include the generic header file instead of the ARM specific one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Arnd Bergmann