The old ctrl in/out routines are non-portable and unsuitable for
cross-platform use. While drivers/sh has already been sanitized, there
is still quite a lot of code that is not. This converts the arch/sh/ bits
over, which permits us to flag the routines as deprecated whilst still
building with -Werror for the architecture code, and to ensure that
future users are not added.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The macro container_of from kernel.h performs the same
pointer arithmetic operation.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression mptr;
expression member;
@@
- (void *)((char *)mptr - offsetof(T, member))
+ container_of(mptr, T, member)
// </smpl>
Signed-off-by: Nicolas Palix <npalix@diku.dk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The typename member of struct irq_chip was kept for migration purposes
and is obsolete since more than 2 years. Fix up the leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It is possible for the CPU to re-enable it's interrupt block bit
before the write to the interrupt controller has actually masked out
the external interupt at the controller. We get around this by
reading back from the interrupt controller which will ensure the
write has happened.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the dependent patches are merged, we are ready to enable
sparseirq support. This simply adds the Kconfig option, and then converts
from the _cpu to the _node allocation routines to follow the upstream
sparseirq API changes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
irq_to_desc_alloc_cpu() has been renamed to irq_to_desc_alloc_node() in
-next, but as we can not presently enable SPARSE_IRQ without the early
irq_desc alloc patch, protect it with an ifdef until the interface has
settled and we are ready to enable it system-wide.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This hooks in irq_to_desc_alloc_cpu() to the necessary code paths in the
intc and ipr controller registration paths. As these are the primary call
paths for all SH CPUs, this alone will make all CPUs sparse IRQ ready.
There is the added benefit now that each CPU contains specific IPR and
INTC tables, so only the vectors with interrupt sources backing them will
ever see an irq_desc instantiation. This effectively packs irq_desc
down to match the CPU, rather than padding NR_IRQS out to cover the valid
vector range.
Boards with extra sources will still have to fiddle with the nr_irqs
setting, but they can continue doing so through the machvec as before.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts a few places that were using the old irq_desc[] array over
to the shiny new irq_to_desc() helper. Preperatory work for sparse irq
support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This tidies up how the SR.IMASK bitmap is managed, using the bitmap API
directly instead. At the same time, tidy up the irq_chip conversion a
bit.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this is special-cased for early initialization. While there are
situations where these static early initializations are still necessary,
with minor changes it is possible to use this for the regular ioremap
implementation as well. This allows us to kill off the special-casing for
the remap completely and to start tidying up all of the SH-5
special-casing in drivers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Impact: cleanup
Convert the last remaining users to struct irq_chip and remove the
define.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The INTC code will be re-used across different architectures, so move
this out to drivers/sh/ and include/linux/sh_intc.h respectively.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the sparc changes a439fe51a1.
Most of the moving about was done with Sam's directions at:
http://marc.info/?l=linux-sh&m=121724823706062&w=2
with subsequent hacking and fixups entirely my fault.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is based on interrupt acknowledge code for external
interrupt sources on sh3 processors and adds on sh4a processors.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the following build error caused by
commit a1dc4b59fa
(sh: intc_sh5 depends on cayman board for IRQ priority table.):
<-- snip -->
...
CC arch/sh/kernel/cpu/irq/intc-sh5.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/kernel/cpu/irq/intc-sh5.c: In function 'plat_irq_setup':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/kernel/cpu/irq/intc-sh5.c:257: error: expected declaration or statement at end of input
make[4]: *** [arch/sh/kernel/cpu/irq/intc-sh5.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The processor models sh7706, sh7707 and sh7709 don't support high
level trigger sense configuration. And the intc code looks like
crap these days so what's the difference.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds interrupt acknowledge code for external interrupt
sources on sh3 processors. Only really required for edge triggered
interrupts, but we ack regardless of sense configuration.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the maskreg irq code since it is not in use anymore.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes interrupt priority tables from the intc code.
Optimal priority assignment varies with embedded application anyway,
so keeping the interrupt priority tables together with cpu-specific
code doesn't make sense.
The function intc_set_priority() should be used instead to set the
desired interrupt priority level.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements initial support for the SMP INTC (particularly
INTC2) controllers.
These are largely implemented as conventional blocks, with
register sets grouped together at fixed strides relative to
the CPU id.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All processor specific interrupt code is now converted to make use
of the new intc code. The config option CONFIG_CPU_HAS_INTC_IRQ is
because of that pointless.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains various intc fixes for problems reported by
Markus Brunner on the linuxsh-dev mailing list:
http://marc.info/?l=linuxsh-dev&m=118701948224991&w=1
Apart from added comments, the fixes are:
- add intc_set_priority() function prototype to hw_irq.h
- fix off-by-one error in intc_set_priority()
- make sure _INTC_WIDTH() is set for primary priority masking
Big thanks to Markus for finding these problems. Version two fixes
a compile error and an inverted primary check.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the intc core, implementing the following features:
- Support dual priority registers - one set and one clear register
- All 8/16/32 bit register combinations are now supported
- Both single mask and single enable bitmap register are supported
- Add code to set interrupt priority
- Speedup sense and priority configuration code
- Allocate data using bootmem, allows intc data structures to be
__initdata
- Save memory - allocated memory footprint is smaller than intc
structures
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We need a secondary register member in struct intc_prio_reg to support
dual priority registers used by ipi on x3.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
IRL doesn't always define sense registers, so don't bother trying to
iterate through the table. This ended up causing an oops on SH-X3
when using IRL mode.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There is no point in keeping around the now unused intc2 code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds single bitmap register support to intc. The current
code only handles 16 and 32 bit registers where a set bit means
interrupt enabled, but this is easy to extend in the future.
The INTC_IRQ() macro is also added to provide a way to hook in
interrupt controllers for FPGAs in boards or companion chips.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes old dead code:
- kill off sh7300 cpu support
- get rid of broken solution engine 7300 board support
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The code in arch/sh/kernel/cpu/irq/pint.c doesn't compile, so let's
get rid of it to make space for a future pint implementation on top
of intc.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch improves intc group support, ie it makes it possible to
group interrupts together and mask / unmask the entire group. This
also works with priorities, so setting a priority for an entire group
is also possible. This patch is needed to properly support certain
processors such as the 7780.
Fixes for NULL pointers in DECLARE_INTC_DESC() are also included.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is the second version of the shared interrupt controller patch
for the sh architecture, fixing up handling of intc_reg_fns[].
The three main advantages with this controller over the existing
ones are:
- Both priority (ipr) and bitmap (intc2) registers are
supported
- External pin sense configuration is supported, ie edge
vs level triggered
- CPU/Board specific code maps 1:1 with datasheet for
easy verification
This controller can easily coexist with the current IPR and INTC2
controllers, but the idea is that CPUs/Boards should be moved over
to this controller over time so we have a single code base to
maintain.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We need to know the CPU ID in order to calculate the mask and ack
registers effectively. Stub this in for UP.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the ipr code by grouping the offset array together
with the ipr_data structure in a new data structure called ipr_desc.
This new structure also contains the name of the controller in struct
irq_chip. The idea behind putting struct irq_chip in there is that we
can use offsetof() to locate the base addresses in the irq_chip
callbacks. This strategy has much in common with the recently merged
intc2 code.
One logic change has been made - the original ipr code enabled the
interrupts by default but with this patch they are all disabled by
default.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The shared intc2 code currently contains cpu-specific #ifdefs.
This is a tad unclean and it prevents us from using the shared code
to drive board-specific irqs on the se7780 board.
This patch reworks the intc2 code by moving the base addresses of
the intc2 registers into struct intc2_desc. This new structure also
contains the name of the controller in struct irq_chip. The idea
behind putting struct irq_chip in there is that we can use offsetof()
to locate the base addresses in the irq_chip callbacks.
One logic change has been made - the original shared intc2 code
enabled the interrupts by default but with this patch they are all
disabled by default.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Thomas Gleixner