This patch adds a new mode of operation to macvlan, called "source".
It allows one to set a list of allowed mac address, which is used
to match against source mac address from received frames on underlying
interface.
This enables creating mac based VLAN associations, instead of standard
port or tag based. The feature is useful to deploy 802.1x mac based
behavior, where drivers of underlying interfaces doesn't allows that.
Configuration is done through the netlink interface using e.g.:
ip link add link eth0 name macvlan0 type macvlan mode source
ip link add link eth0 name macvlan1 type macvlan mode source
ip link set link dev macvlan0 type macvlan macaddr add 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr add 00:22:22:22:22:22
ip link set link dev macvlan0 type macvlan macaddr add 00:33:33:33:33:33
ip link set link dev macvlan1 type macvlan macaddr add 00:33:33:33:33:33
ip link set link dev macvlan1 type macvlan macaddr add 00:44:44:44:44:44
This allows clients with MAC addresses 00:11:11:11:11:11,
00:22:22:22:22:22 to be part of only VLAN associated with macvlan0
interface. Clients with MAC addresses 00:44:44:44:44:44 with only VLAN
associated with macvlan1 interface. And client with MAC address
00:33:33:33:33:33 to be associated with both VLANs.
Based on work of Stefan Gula <steweg@gmail.com>
v8: last version of Stefan Gula for Kernel 3.2.1
v9: rework onto linux-next 2014-03-12 by Michael Braun
add MACADDR_SET command, enable to configure mac for source mode
while creating interface
v10:
- reduce indention level
- rename source_list to source_entry
- use aligned 64bit ether address
- use hash_64 instead of addr[5]
v11:
- rebase for 3.14 / linux-next 20.04.2014
v12
- rebase for linux-next 2014-09-25
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 412ca1550c ("macvlan: Move broadcasts into a work queue"), the
driver uses tx_queue_len of the master device as the limit of packets enqueuing.
Problem is that virtual drivers have this value set to 0, thus all broadcast
packets were rejected.
Because tx_queue_len was arbitrarily chosen, I replace it with a static limit
of 1000 (also arbitrarily chosen).
CC: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: Thibaut Collet <thibaut.collet@6wind.com>
Suggested-by: Thibaut Collet <thibaut.collet@6wind.com>
Tested-by: Thibaut Collet <thibaut.collet@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
I cannot move a macvlan interface created on top of a bonding interface
to a different namespace:
% ip netns add dummy0
% ip link add link bond0 mac0 type macvlan
% ip link set mac0 netns dummy0
RTNETLINK answers: Invalid argument
%
The problem seems to be that commit f939981492 ("bonding: Don't allow
bond devices to change network namespaces.") sets NETIF_F_NETNS_LOCAL
on bonding interfaces, and commit 797f87f83b ("macvlan: fix netdev
feature propagation from lower device") causes macvlan interfaces
to inherit its features from the lower device.
NETIF_F_NETNS_LOCAL should not be inherited from the lower device
by a macvlan.
Patch tested on 3.16.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, macvlan code restricts multicast and unicast
filter setting only to passthru devices. As a result,
if a guest using macvtap wants to receive multicast
traffic, it has to set IFF_ALLMULTI or IFF_PROMISC.
This patch makes it possible to use the fdb interface
to add multicast addresses to the filter thus allowing
a guest to receive only targeted multicast traffic.
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macvlan devices do not initialize vlan_features. As a result,
any vlan devices configured on top of macvlans perform very poorly.
Initialize vlan_features based on the vlan features of the lower-level
device.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/core/rtnetlink.c
net/core/skbuff.c
Both conflicts were very simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
unregister_netdevice_many() API is error prone and we had too
many bugs because of dangling LIST_HEAD on stacks.
See commit f87e6f4793 ("net: dont leave active on stack LIST_HEAD")
In fact, instead of making sure no caller leaves an active list_head,
just force a list_del() in the callee. No one seems to need to access
the list after unregister_netdevice_many()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bonding and team drivers generate specific events during failover
that trigger switch updates. When a macvlan device is configured
on top of bonding, we want switches to learn about the macvlan
devices as well. This patch adds a handler to macvlan driver to
propagate these events to all macvlan devices. We let the generic
inetdev event handler do the work.
This allows macvlan to operated correctly over active-backup
mode bond.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netpoll support to macvlan devices. Based on the netpoll support in the 802.1q vlan code.
Tested and macvlan could work well with netconsole.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macvlan dev should always have the same mac address like lowerdev
when in the passthru mode, change the mac address alone will break the
work mechanism, so when the lowerdev or macvlan mac address changes,
we should propagate the changes to another dev.
v1->v2: Allow macvlan dev to change mac address for passthru mode and propagate to
lowerdev.
v2->v3: Don't set the mac address to the lower dev's unicast address for
passthru mode when mac address changes.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The port->count was used to count the number of macvlan devs
in the same port, but the list vlans could play the same role
to do that, so free the port if the list vlans is empty and
no need to use the parameter count.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the physical MTU changes we should ensure that all existing MACVLAN
dev MTU do not exceed the new lowerdev MTU. This patch adds that
propagation.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing the IFF_ALLMULTI flag on a down interface could cause an allmulti
overflow on the underlying interface.
Attempting the set IFF_ALLMULTI on the underlying interface would cause an
error and the log message:
"allmulti touches root, set allmulti failed."
Signed-off-by: Peter Christensen <pch@ordbogen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 12a2856b60.
The commit above doesn't appear to be necessary any more as the
checksums appear to be correctly computed/validated.
Additionally the above commit breaks kvm configurations where
one VM is using a device that support checksum offload (virtio) and
the other VM does not.
In this case, packets leaving virtio device will have CHECKSUM_PARTIAL
set. The packets is forwarded to a macvtap that has offload features
turned off. Since we use CHECKSUM_UNNECESSARY, the host does does not
update the checksum and thus a bad checksum is passed up to
the guest.
CC: Daniel Lezcano <daniel.lezcano@free.fr>
CC: Patrick McHardy <kaber@trash.net>
CC: Andrian Nord <nightnord@gmail.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch that moved broadcasts to process context added
a couple of bugs on the error path where we may dereference NULL
or leak an skb. This patch fixes them.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently broadcasts are handled in network RX context, where
the packets are sent through netif_rx. This means that the number
of macvlans will be constrained by the capacity of netif_rx.
For example, setting up 4096 macvlans practically causes all
broadcast packets to be dropped as the default netif_rx queue
size simply can't handle 4096 skbs being stuffed into it all
at once.
Fundamentally, we need to ensure that the amount of work handled
in each netif_rx backlog run is constrained. As broadcasts are
anything but constrained, it either needs to be limited per run
or moved to process context.
This patch picks the second option and moves all broadcast handling
bar the trivial case of packets going to a single interface into
a work queue. Obviously there also needs to be a limit on how
many broadcast packets we postpone in this way. I've arbitrarily
chosen tx_queue_len of the master device as the limit (act_mirred
also happens to use this parameter in a similar way).
In order to ensure we don't exceed the backlog queue we will use
netif_rx_ni instead of netif_rx for broadcast packets.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the bh safe variant with the hard irq safe variant.
We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.
Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Macvlan currently inherits all of its features from the lower
device. When lower device disables offload support, this causes
macvlan to disable offload support as well. This causes
performance regression when using macvlan/macvtap in bridge
mode.
It can be easily demonstrated by creating 2 namespaces using
macvlan in bridge mode and running netperf between them:
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 20.00 1204.61
To restore the performance, we add software offload features
to the list of "always_on" features for macvlan. This way
when a namespace or a guest using macvtap initially sends a
packet, this packet will not be segmented at macvlan level.
It will only be segmented when macvlan sends the packet
to the lower device.
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 20.00 5507.35
Fixes: 6acf54f1cf (macvtap: Add support of packet capture on macvtap device.)
Fixes: 797f87f83b (macvlan: fix netdev feature propagation from lower device)
CC: Florian Westphal <fw@strlen.de>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
CC: Jason Wang <jasowang@redhat.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many drivers calling alloc_percpu() to allocate pcpu stats
and then initializing ->syncp. So just introduce a helper function for them.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_newlink() doesn't unregister it for us on failure.
Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the tx queue were selected implicitly in ndo_dfwd_start_xmit(). The
will cause several issues:
- NETIF_F_LLTX were removed for macvlan, so txq lock were done for macvlan
instead of lower device which misses the necessary txq synchronization for
lower device such as txq stopping or frozen required by dev watchdog or
control path.
- dev_hard_start_xmit() was called with NULL txq which bypasses the net device
watchdog.
- dev_hard_start_xmit() does not check txq everywhere which will lead a crash
when tso is disabled for lower device.
Fix this by explicitly introducing a new param for .ndo_select_queue() for just
selecting queues in the case of l2 forwarding offload. netdev_pick_tx() was also
extended to accept this parameter and dev_queue_xmit_accel() was used to do l2
forwarding transmission.
With this fixes, NETIF_F_LLTX could be preserved for macvlan and there's no need
to check txq against NULL in dev_hard_start_xmit(). Also there's no need to keep
a dedicated ndo_dfwd_start_xmit() and we can just reuse the code of
dev_queue_xmit() to do the transmission.
In the future, it was also required for macvtap l2 forwarding support since it
provides a necessary synchronization method.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2 fowarding offload will bypass the rx handler of real device. This will make
the packet could not be forwarded to macvtap device. Another problem is the
dev_hard_start_xmit() called for macvtap does not have any synchronization.
Fix this by forbidding L2 forwarding for macvtap.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
They are same, so unify them as one; since macvlan is a kind of vlan,
vlan_pcpu_stats should be a proper name for vlan and macvlan.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only used in one file, no need to expose
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are inconsistencies wrt. feature propagation/inheritance between
macvlan and the underlying interface.
When a feature is turned off on the real device before a macvlan is
created on top, these will remain enabled on the macvlan device, whereas
turning off the feature on the lower device after macvlan creation the
kernel will propagate the changes to the macvlan.
The second issue is that, when propagating changes from underlying device
to the macvlan interface, macvlan can erronously lose its NETIF_F_LLTX flag,
as features are anded with the underlying device.
However, LLTX should be kept since it has no dependencies on physical
hardware (LLTX is set on macvlan creation regardless of the lower
device properties, see 8ffab51b3d
(macvlan: lockless tx path).
The LLTX flag is now forced regardless of user settings in absence of
layer2 hw acceleration (a6cc0cfa72,
net: Add layer 2 hardware acceleration operations for macvlan devices).
Use netdev_increment_features to rebuild the feature set on capability
changes on either the lower device or on the macvlan interface.
As pointed out by Ben Hutchings, use netdev_update_features on
NETDEV_FEAT_CHANGE event (it calls macvlan_fix_features/netdev_features_change
if needed).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since now macvlan and macvtap use the same receive and
forward handlers, we can remove them completely and use
netif_rx and dev_forward_skb() directly.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in a network namespace whose only link to the outside
world is a macvlan device, not being able to create a macvtap off of
it is a real pain.
So modify macvtap creation to automatically forward a creation of a
macvtap on a macvlan to become a creation of a macvtap on the
underlying network device, just like is currently done with
macvlan-on-macvlan devices.
v2: Use netif_is_macvlan and macvlan_dev_real_dev helpers to make it
more clear what we're doing.
Signed-off-by: Kevin Wallace <kevin@pentabarf.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull core locking changes from Ingo Molnar:
"The biggest changes:
- add lockdep support for seqcount/seqlocks structures, this
unearthed both bugs and required extra annotation.
- move the various kernel locking primitives to the new
kernel/locking/ directory"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
block: Use u64_stats_init() to initialize seqcounts
locking/lockdep: Mark __lockdep_count_forward_deps() as static
lockdep/proc: Fix lock-time avg computation
locking/doc: Update references to kernel/mutex.c
ipv6: Fix possible ipv6 seqlock deadlock
cpuset: Fix potential deadlock w/ set_mems_allowed
seqcount: Add lockdep functionality to seqcount/seqlock structures
net: Explicitly initialize u64_stats_sync structures for lockdep
locking: Move the percpu-rwsem code to kernel/locking/
locking: Move the lglocks code to kernel/locking/
locking: Move the rwsem code to kernel/locking/
locking: Move the rtmutex code to kernel/locking/
locking: Move the semaphore core to kernel/locking/
locking: Move the spinlock code to kernel/locking/
locking: Move the lockdep code to kernel/locking/
locking: Move the mutex code to kernel/locking/
hung_task debugging: Add tracepoint to report the hang
x86/locking/kconfig: Update paravirt spinlock Kconfig description
lockstat: Report avg wait and hold times
lockdep, x86/alternatives: Drop ancient lockdep fixup message
...
Add a operations structure that allows a network interface to export
the fact that it supports package forwarding in hardware between
physical interfaces and other mac layer devices assigned to it (such
as macvlans). This operaions structure can be used by virtual mac
devices to bypass software switching so that forwarding can be done
in hardware more efficiently.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to enable lockdep on seqcount/seqlock structures, we
must explicitly initialize any locks.
The u64_stats_sync structure, uses a seqcount, and thus we need
to introduce a u64_stats_init() function and use it to initialize
the structure.
This unfortunately adds a lot of fairly trivial initialization code
to a number of drivers. But the benefit of ensuring correctness makes
this worth while.
Because these changes are required for lockdep to be enabled, and the
changes are quite trivial, I've not yet split this patch out into 30-some
separate patches, as I figured it would be better to get the various
maintainers thoughts on how to best merge this change along with
the seqcount lockdep enablement.
Feedback would be appreciated!
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Roger Luethi <rl@hellgate.ch>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Simon Horman <horms@verge.net.au>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Wensong Zhang <wensong@linux-vs.org>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/1381186321-4906-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
After the commit below attempting to create macvlan devices was
resulting in ENOENT errors,
# ip link add link p3p2 type macvlan
RTNETLINK answers: Invalid argument
This happens because netdev_upper_dev_link() is called before
register_netdevice() in the macvlan code. Through a call chain
this results in a call to __netdev_adjacent_dev_insert() and
finally a sysfs_create_link(). This requires the kobject of
the macvlan to be registered which is done in register_netdevice().
If there is no kobject which is the case here the ENOENT error
is seen on the command line.
To resolve this move the netdev_upper_dev_link() call below
the register_netdevice() call. This aligns with vlan driver
flow.
Regression introduced here,
commit 5831d66e80
Author: Veaceslav Falico <vfalico@redhat.com>
Date: Wed Sep 25 09:20:32 2013 +0200
net: create sysfs symlinks for neighbour devices
CC: Veaceslav Falico <vfalico@redhat.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently macvlan calls skb_clone in macvlan_broadcast but checks
for a NULL return in macvlan_broadcast_one instead. This is
needlessly confusing and may lead to bugs introduced later.
This patch moves the error check to where the skb_clone call is.
The only other caller of macvlan_broadcast_one never passes in a
NULL value so it doesn't need the check either.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A device inheriting a random or set address should reflect this in
its addr_assign_type.
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 3b04ddde02
"[NET]: Move hardware header operations out of netdevice."
moved the handling into macvlan setup adding
dev->header_ops = &macvlan_hard_header_ops,
At the end of the line the ',' should have been a ';'
Signed-off-by: Lutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit df8ef8f3aa
macvlan: add FDB bridge ops and macvlan flags
added a flags field to macvlan, which can be
controlled from userspace.
The idea is to make the interface future-proof
so we can add flags and not new fields.
However, flags value isn't validated, as a result,
userspace can't detect which flags are supported.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's quite unlikely that dev_set_promiscuity will fail,
but worth checking just in case.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macvlan passthrough mode is special: it's not possible to switch to or
from it through a netlink command.
But if you try, the command will succeed, which is
confusing.
Validate input and return error to user.
Cc: Sridhar Samudrala <sri@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for iproute2 command 'bridge fdb replace ...'.
The rtnletlink call back function ndo_fdb_add will be called
with the NLM_F_REPLACE flag set.
Simply return -EOPNOTSUP.
Resubmitted because net-next was closed last week.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the user issues TUNSETOFFLOAD ioctl, macvtap does not do
anything other then to verify arguments. This patch adds
functionality to allow users to actually control offload features.
NETIF_F_GSO and NETIF_F_GRO are always on, but the rest of the
features can be controlled.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit df8ef8f3aa
"macvlan: add FDB bridge ops and macvlan flags"
added a way to control NOPROMISC macvlan flag through netlink.
However, with a non passthrough device we never set promisc on open,
even if NOPROMISC is off. As a result:
If userspace clears NOPROMISC on open, then does not clear it on a
netlink command, promisc counter is not decremented on stop and there
will be no way to clear it once macvlan is detached.
If userspace does not clear NOPROMISC on open, then sets NOPROMISC on a
netlink command, promisc counter will be decremented from 0 and overflow
to fffffffff with no way to clear promisc.
To fix, simply ignore NOPROMISC flag in a netlink command for
non-passthrough devices, same as we do at open/close.
Since we touch this code anyway - check dev_set_promiscuity return code
and pass it to users (though an error here is unlikely).
Cc: "David S. Miller" <davem@davemloft.net>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
v2->v3: fix typo on simeth
shortened dev_getter
shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if macvlan in passthru mode is created and data are rxed and
you remove this device, following panic happens:
NULL pointer dereference at 0000000000000198
IP: [<ffffffffa0196058>] macvlan_handle_frame+0x153/0x1f7 [macvlan]
I'm using following script to trigger this:
<script>
while [ 1 ]
do
ip link add link e1 name macvtap0 type macvtap mode passthru
ip link set e1 up
ip link set macvtap0 up
IFINDEX=`ip link |grep macvtap0 | cut -f 1 -d ':'`
cat /dev/tap$IFINDEX >/dev/null &
ip link del dev macvtap0
done
</script>
I run this script while "ping -f" is running on another machine to send
packets to e1 rx.
Reason of the panic is that list_first_entry() is blindly called in
macvlan_handle_frame() even if the list was empty. vlan is set to
incorrect pointer which leads to the crash.
I'm fixing this by protecting port->vlans list by rcu and by preventing
from getting incorrect pointer in case the list is empty.
Introduced by: commit eb06acdc85 "macvlan: Introduce 'passthru' mode to takeover the underlying device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- macvlan: propagate STAG filtering capabilities from underlying device
- ifb: announce STAG tagging support in addition to CTAG tagging support
- veth: announce STAG tagging/stripping support in addition to CTAG support
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we use proper API to fetch dev->rx_handler_data,
instead of ugly casts.
Rename macvlan_port_get() to macvlan_port_get_rtnl() to document fact
that we hold RTNL when needed, with lockdep support.
This removes sparse warnings as well (CONFIG_SPARSE_RCU_POINTER=y)
CHECK drivers/net/macvlan.c
drivers/net/macvlan.c:706:37: warning: cast removes address space of expression
drivers/net/macvlan.c:775:16: warning: cast removes address space of expression
drivers/net/macvlan.c:924:16: warning: cast removes address space of expression
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macvlan already supports hw address filters. Set the IFF_UNICAST_FLT
so that it doesn't needlesly enter PROMISC mode when macvlans are
stacked.
Signed-of-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a user adds bridge neighbors, allow him to specify VLAN id.
If the VLAN id is not specified, the neighbor will be added
for VLANs currently in the ports filter list. If no VLANs are
configured on the port, we use vlan 0 and only add 1 entry.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some multicast addresses are common to all macvlans,
so if a multicast message has a hash value collision, we
have to deliver a copy to all macvlans, adding significant
latency and possible packet drops if netdev_max_backlog
limit is hit.
Having a per macvlan hash function permits to reduce the
impact of hash collisions.
Suggested-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit cd431e7385 (macvlan: add multicast filter) forgot
the broadcast case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
SIgned-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting up IPv6 addresses on configurations with many macvlans
is not really working, as many multicast messages are dropped.
Add a multicast filter to macvlan to reduce the amount of cloned
skbs and overhead.
Successfully tested with 1024 macvlans on one ethernet device.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit df8ef8f3aa (macvlan: add FDB bridge ops and macvlan flags)
forgot to update macvlan_get_size() after the addition of
IFLA_MACVLAN_FLAGS
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_ADDR_SET is set in dev_set_mac_address() no need to alter
dev->addr_assign_type value in drivers.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Later changes need to be able to refer to neighbour attributes
when doing fdb_add.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal functions for add/deleting addresses don't change
their argument.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal_64bits to add
some clarity and reduce the likelihood for misuse of
compare_ether_addr_64bits for sorting.
Done via cocci script:
$ cat compare_ether_addr_64bits.cocci
@@
expression a,b;
@@
- !compare_ether_addr_64bits(a, b)
+ ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- compare_ether_addr_64bits(a, b)
+ !ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- !ether_addr_equal_64bits(a, b) == 0
+ ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- !ether_addr_equal_64bits(a, b) != 0
+ !ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- ether_addr_equal_64bits(a, b) == 0
+ !ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- ether_addr_equal_64bits(a, b) != 0
+ ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal_64bits(a, b)
+ ether_addr_equal_64bits(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8a83a00b07.
It causes regressions for S390 devices, because it does an
unconditional DST drop on SKBs for vlans and the QETH device
needs the neighbour entry hung off the DST for certain things
on transmit.
Arnd can't remember exactly why he even needed this change.
Conflicts:
drivers/net/macvlan.c
net/8021q/vlan_dev.c
net/core/dev.c
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds FDB bridge ops to the macvlan device passthru mode.
Additionally a flags field was added and a NOPROMISC bit to
allow users to use passthru mode without the driver calling
dev_set_promiscuity(). The flags field is a u16 placed in a
4 byte hole (consuming 2 bytes) of the macvlan_dev struct.
We want to do this so that the macvlan driver or stack
above the macvlan driver does not have to process every
packet. For the use case where we know all the MAC addresses
of the endstations above us this works well.
This patch is a result of Roopa Prabhu's work. Follow up
patches are needed for VEPA and VEB macvlan modes.
v2: Change from distinct nopromisc mode to a flags field to
configure this. This avoids the tendency to add a new
mode every time we need some slightly different behavior.
v3: fix error in dev_set_promiscuity and add change and get
link attributes for flags.
CC: Roopa Prabhu <roprabhu@cisco.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bc416d9768 (macvlan: handle fragmented multicast frames) added a
possible use after free in macvlan_handle_frame(), since
ip_check_defrag() uses pskb_may_pull() : skb header can be reallocated.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds wrapper for ndo_vlan_rx_add_vid/ndo_vlan_rx_kill_vid
functions. Check for NETIF_F_HW_VLAN_FILTER feature is done in this
wrapper.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing VRRP v2 using macvlan several problems were
discovered. VRRP is weird in that all routers participating
in a redundant group use the same virtual MAC address.
Macvlan is a natural driver to use for this but it doesn't
work. The problem is that packets with a macvlan device's
source address are not received.
The problem is actually a regression that date back almost 2 years now.
The original problems started with:
commit 618e1b7482
Author: Arnd Bergmann <arnd@arndb.de>
Date: Thu Nov 26 06:07:10 2009 +0000
macvlan: implement bridge, VEPA and private mode
This patches restores the original 2.6.32 behavior. Allowing multicast
packets received with the VRRP source address to be received.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fragmented multicast frames are delivered to a single macvlan port,
because ip defrag logic considers other samples are redundant.
Implement a defrag step before trying to send the multicast frame.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets should always be forwarded to the lowerdev using dev_forward_skb.
vlan->forward is for packets being forwarded directly to another macvlan/
macvtap device (used for multicast in bridge mode).
Reported-and-tested-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does several things:
- introduces __ethtool_get_settings which is called from ethtool code and
from drivers as well. Put ASSERT_RTNL there.
- dev_ethtool_get_settings() is replaced by __ethtool_get_settings()
- changes calling in drivers so rtnl locking is respected. In
iboe_get_rate was previously ->get_settings() called unlocked. This
fixes it. Also prb_calc_retire_blk_tmo() in af_packet.c had the same
problem. Also fixed by calling __dev_get_by_index() instead of
dev_get_by_index() and holding rtnl_lock for both calls.
- introduces rtnl_lock in bnx2fc_vport_create() and fcoe_vport_create()
so bnx2fc_if_create() and fcoe_if_create() are called locked as they
are from other places.
- use __ethtool_get_settings() in bonding code
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v2->v3:
-removed dev_ethtool_get_settings()
-added ASSERT_RTNL into __ethtool_get_settings()
-prb_calc_retire_blk_tmo - use __dev_get_by_index() and lock
around it and __ethtool_get_settings() call
v1->v2:
add missing export_symbol
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> [except FCoE bits]
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs. There are a handful of drivers that violate this assumption of
course, and need to be fixed up. This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_vlan_rx_register is no longer in use in any driver so remove it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stacking VLANs on top of the macvlan device does not
work if the lowerdev device is using vlan filters set
by NETIF_F_HW_VLAN_FILTER. Add ndo ops to pass vlan
calls to lowerdev.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unicast frames between macvlan interfaces in bridge mode are not otherwise
sent to network taps on the lowerdev (as all other macvlan frames are), so
forward the frames to the receive queue of the lowerdev first.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
commit a35e2c1b6d (macvlan: use rx_handler_data pointer to store
macvlan_port pointer V2) added a bug in macvlan_port_create()
Steps to reproduce the bug:
# ifenslave bond0 eth0 eth1
# ip link add link eth0 up name eth0#1 type macvlan
->error EBUSY
# ip link add link eth0 up name eth0#1 type macvlan
->panic
Fix: Dont set IFF_MACVLAN_PORT in error case.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When one macvlan device is dismantled, we can avoid one
synchronize_rcu() call done after deletion from hash list, since caller
will perform a synchronize_net() call after its ndo_stop() call.
Add a new netdev->dismantle field to signal this dismantle intent.
Reduces RTNL hold time.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
CC: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
veth devices dont use the batched device unregisters yet.
Since veth are a pair of devices, it makes sense to use a batch of two
unregisters, this roughly divides dismantle time by two.
Fix this by changing dellink() callers to always provide a non NULL
head. (Idea from Michał Mirosław)
This patch also handles macvlan case : We now dismantle all macvlans on
top of a lower dev at once.
Reported-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Michał Mirosław <mirqus@gmail.com>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rcu callback macvlan_port_rcu_free() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(macvlan_port_rcu_free).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Not much of a conversion anyway - macvlan has no way to change the offload
settings independently to its base device.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the macvlan driver was extended to call unregisgter_netdevice_queue
in 23289a37e2, a use after free of struct
macvlan_port was introduced. The code in dellink relied on unregister_netdevice
actually unregistering the net device so it would be safe to free macvlan_port.
Since unregister_netdevice_queue can just queue up the unregister instead of
performing the unregiser immediately we free the macvlan_port too soon and
then the code in macvlan_stop removes the macaddress for the set of macaddress
to listen for and uses memory that has already been freed.
To fix this add a reference count to track when it is safe to free the macvlan_port
and move the call of macvlan_port_destroy into macvlan_uninit which is guaranteed
to be called after the final macvlan_port_close.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows rx_handlers to better signalize what to do next to
it's caller. That makes skb->deliver_no_wcard no longer needed.
kernel-doc for rx_handler_result is taken from Nicolas' patch.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the lower device has offloading capabilities, the packets checksums
are not computed. That leads to have any macvlan port in bridge mode to
not work because the packets are dropped due to a bad checksum.
If the macvlan is in bridge mode, the packet is forwarded to another
macvlan port and reach the network stack where it looks for a checksum
but this one was not computed due to the offloading of the lower device.
In this case, we have to set the packet with CHECKSUM_UNNECESSARY
when it is forwarded to a bridged port and restore the previous value of
ip_summed when the packet goes to the lowerdev.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Andrian Nord <nightnord@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the current default 'vepa' mode, a KVM guest using virtio with
macvtap backend has the following limitations.
- cannot change/add a mac address on the guest virtio-net
- cannot create a vlan device on the guest virtio-net
- cannot enable promiscuous mode on guest virtio-net
To address these limitations, this patch introduces a new mode called
'passthru' when creating a macvlan device which allows takeover of the
underlying device and passing it to a guest using virtio with macvtap
backend.
Only one macvlan device is allowed in passthru mode and it inherits
the mac address from the underlying device and sets it in promiscuous
mode to receive and forward all the packets.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
-------------------------------------------------------------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
macvlan is a stacked device, like tunnels. We should use the lockless
mechanism we are using in tunnels and loopback.
This patch completely removes locking in TX path.
tx stat counters are added into existing percpu stat structure, renamed
from rx_stats to pcpu_stats.
Note : this reverts commit 2c11455321 (macvlan: add multiqueue
capability)
Note : rx_errors converted to a 32bit counter, like tx_dropped, since
they dont need 64bit range.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Braun