In some cases, there is a need to enable a clock as part of
clock enable callback of a different clock. For example, USB
2.0 PHY clock enable requires USB 2.0 clock to be enabled.
In this case, it is safe to instead call __clk_enable()
since the clock framework lock is already taken. Calling
clk_enable() causes recursive locking error.
A similar case arises in the clock disable path.
To enable such usage, make __clk_{enable,disable} functions
publicly available outside of clock.c. Also, call them
davinci_clk_{enable|disable} now to be consistent with how
other davinci-specific clock functions are named.
Note that these functions are not exported to drivers. They
are meant for usage in platform specific clock management
code.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Suggested-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Similarly to the aemif clock - this screws up the linked list of clock
children. Create a separate clock for mdio inheriting the rate from
emac_clk.
Cc: <stable@vger.kernel.org> # 3.12.x-
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: add a comment over mdio_clk to explaing its existence +
commit headline updates]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The aemif clock is added twice to the lookup table in da850.c. This
breaks the children list of pll0_sysclk3 as we're using the same list
links in struct clk. When calling clk_set_rate(), we get stuck in
propagate_rate().
Create a separate clock for nand, inheriting the rate of the aemif
clock and retrieve it in the davinci_nand module.
Cc: <stable@vger.kernel.org> # 4.9.x
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There is no need to define map_io only for debug_ll_io_init() since it
is already called in devicemaps_init() if map_io is NULL.
Apart from that, for NOMMU build debug_ll_io_init() is a nop which
leads to following error:
CC arch/arm/mach-imx/mach-imx1.o
arch/arm/mach-imx/mach-imx1.c:40:13: error: 'debug_ll_io_init' undeclared here (not in a function)
.map_io = debug_ll_io_init,
^
make[1]: *** [arch/arm/mach-imx/mach-imx1.o] Error 1
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Found while reviewing Marvell dsa bindings usage.
Fixes: f283745b3c ("arm: vf610: zii devel b: Add support for switch interrupts")
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The NANDF_CS2 pad is also part of the wlan-vmmcgrp iomux group.
Removing is from the usdhc2grp group avoids the following error:
imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_NANDF_CS2 already requested
by regulators:regulator@4; cannot claim for 2194000.usdhc
imx6q-pinctrl 20e0000.iomuxc: pin-187 (2194000.usdhc) status -22
imx6q-pinctrl 20e0000.iomuxc: could not request pin 187
(MX6Q_PAD_NANDF_CS2) from group usdhc2grp on device 20e0000.iomuxc
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX31 AVIC interrupt controller base address is at 0x68000000.
The problem was shadowed by the AVIC driver, which takes the correct
base address from a SoC specific header file.
Fixes: d2a37b3d91 ("ARM i.MX31: Add devicetree support")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull DAX updates from Dan Williams:
"The completion of Jan's DAX work for 4.10.
As I mentioned in the libnvdimm-for-4.10 pull request, these are some
final fixes for the DAX dirty-cacheline-tracking invalidation work
that was merged through the -mm, ext4, and xfs trees in -rc1. These
patches were prepared prior to the merge window, but we waited for
4.10-rc1 to have a stable merge base after all the prerequisites were
merged.
Quoting Jan on the overall changes in these patches:
"So I'd like all these 6 patches to go for rc2. The first three
patches fix invalidation of exceptional DAX entries (a bug which
is there for a long time) - without these patches data loss can
occur on power failure even though user called fsync(2). The other
three patches change locking of DAX faults so that ->iomap_begin()
is called in a more relaxed locking context and we are safe to
start a transaction there for ext4"
These have received a build success notification from the kbuild
robot, and pass the latest libnvdimm unit tests. There have not been
any -next releases since -rc1, so they have not appeared there"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
ext4: Simplify DAX fault path
dax: Call ->iomap_begin without entry lock during dax fault
dax: Finish fault completely when loading holes
dax: Avoid page invalidation races and unnecessary radix tree traversals
mm: Invalidate DAX radix tree entries only if appropriate
ext2: Return BH_New buffers for zeroed blocks
Add 'gpios' property to pcie1 dt node and populate it with
GPIO3_23 in order to drive PCIE_RESETn high.
This gets PCIe cards to be detected in AM572X IDK board.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- A merge error on my part broke the DocBook build. I've requisitioned
one of tglx's frozen sharks for appropriate disciplinary action and
resolved to be more careful about testing the DocBook stuff as long as
it's still around.
- Fix an error in unaligned-memory-access.txt
-----BEGIN PGP SIGNATURE-----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=W4e5
-----END PGP SIGNATURE-----
Merge tag 'docs-4.10-rc1-fix' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"Two small fixes:
- A merge error on my part broke the DocBook build. I've
requisitioned one of tglx's frozen sharks for appropriate
disciplinary action and resolved to be more careful about testing
the DocBook stuff as long as it's still around.
- Fix an error in unaligned-memory-access.txt"
* tag 'docs-4.10-rc1-fix' of git://git.lwn.net/linux:
Documentation/unaligned-memory-access.txt: fix incorrect comparison operator
docs: Fix build failure
Pull crypto fix from Herbert Xu:
"This fixes a boot failure on some platforms when crypto self test is
enabled along with the new acomp interface"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: testmgr - Use heap buffer for acomp test input
The GICv2 CPU interface registers span across 8K, not 4K as indicated in
the DT. Only the GICC_DIR register is located after the initial 4K
boundary, leaving a functional system but without support for separately
EOI'ing and deactivating interrupts.
After this change the system supports split priority drop and interrupt
deactivation. This patch is based on similar one from Christoffer Dall:
commit 368400e242 ("ARM: dts: vexpress: Support GICC_DIR operations")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The GICv2 CPU interface registers span across 8K, not 4K as indicated in
the DT. Only the GICC_DIR register is located after the initial 4K
boundary, leaving a functional system but without support for separately
EOI'ing and deactivating interrupts.
After this change the system supports split priority drop and interrupt
deactivation.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
[sudeep.holla@arm.com: included same fix for tc1 platform too]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The pre-1.0 SCPI firmwares are using single __le32 as sensor value,
while the SCPI v1.0 protocol uses two __le32 as sensor values(64bit)
split into 32bit upper and 32bit lower value.
Using an "struct sensor_value" to read the sensor value on a pre-1.0
SCPI firmware gives garbage in the "hi_val" field.
This patch fixes the issue by reading only the lower 32-bit value for
all pre-1.0 SCPI versions.
Suggested-by: Sudeep Holla <Sudeep.Holla@arm.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[sudeep.holla@arm.com: updated the commit log to reflect the implementation]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
mm/filemap.c: In function 'clear_bit_unlock_is_negative_byte':
mm/filemap.c:933:9: error: too few arguments to function 'test_bit'
return test_bit(PG_waiters);
^~~~~~~~
Fixes: b91e1302ad ('mm: optimize PageWaiters bit use for unlock_page()')
Signed-off-by: Olof Johansson <olof@lixom.net>
Brown-paper-bag-by: Linus Torvalds <dummy@duh.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit 6290602709 ("mm: add PageWaiters indicating tasks are
waiting for a page bit") Nick Piggin made our page locking no longer
unconditionally touch the hashed page waitqueue, which not only helps
performance in general, but is particularly helpful on NUMA machines
where the hashed wait queues can bounce around a lot.
However, the "clear lock bit atomically and then test the waiters bit"
sequence turns out to be much more expensive than it needs to be,
because you get a nasty stall when trying to access the same word that
just got updated atomically.
On architectures where locking is done with LL/SC, this would be trivial
to fix with a new primitive that clears one bit and tests another
atomically, but that ends up not working on x86, where the only atomic
operations that return the result end up being cmpxchg and xadd. The
atomic bit operations return the old value of the same bit we changed,
not the value of an unrelated bit.
On x86, we could put the lock bit in the high bit of the byte, and use
"xadd" with that bit (where the overflow ends up not touching other
bits), and look at the other bits of the result. However, an even
simpler model is to just use a regular atomic "and" to clear the lock
bit, and then the sign bit in eflags will indicate the resulting state
of the unrelated bit #7.
So by moving the PageWaiters bit up to bit #7, we can atomically clear
the lock bit and test the waiters bit on x86 too. And architectures
with LL/SC (which is all the usual RISC suspects), the particular bit
doesn't matter, so they are fine with this approach too.
This avoids the extra access to the same atomic word, and thus avoids
the costly stall at page unlock time.
The only downside is that the interface ends up being a bit odd and
specialized: clear a bit in a byte, and test the sign bit. Nick doesn't
love the resulting name of the new primitive, but I'd rather make the
name be descriptive and very clear about the limitation imposed by
trying to work across all relevant architectures than make it be some
generic thing that doesn't make the odd semantics explicit.
So this introduces the new architecture primitive
clear_bit_unlock_is_negative_byte();
and adds the trivial implementation for x86. We have a generic
non-optimized fallback (that just does a "clear_bit()"+"test_bit(7)"
combination) which can be overridden by any architecture that can do
better. According to Nick, Power has the same hickup x86 has, for
example, but some other architectures may not even care.
All these optimizations mean that my page locking stress-test (which is
just executing a lot of small short-lived shell scripts: "make test" in
the git source tree) no longer makes our page locking look horribly bad.
Before all these optimizations, just the unlock_page() costs were just
over 3% of all CPU overhead on "make test". After this, it's down to
0.66%, so just a quarter of the cost it used to be.
(The difference on NUMA is bigger, but there this micro-optimization is
likely less noticeable, since the big issue on NUMA was not the accesses
to 'struct page', but the waitqueue accesses that were already removed
by Nick's earlier commit).
Acked-by: Nick Piggin <npiggin@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds required memory carveouts so that the kernel does not
access memory that is in use or has been reserved for use by other remote
processors.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
I use Patchwork for handling incoming patches. Put its address here so
submitters could know what is in the queue.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Kukjin Kim <kgene@kernel.org>
Pull crypto fix from Herbert Xu:
"This fixes a hash corruption bug in the marvell driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: marvell - Copy IVDIG before launching partial DMA ahash requests
Pull networking fixes from David Miller:
1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.
The most important is to not assume the packet is RX just because
the destination address matches that of the device. Such an
assumption causes problems when an interface is put into loopback
mode.
2) If we retry when creating a new tc entry (because we dropped the
RTNL mutex in order to load a module, for example) we end up with
-EAGAIN and then loop trying to replay the request. But we didn't
reset some state when looping back to the top like this, and if
another thread meanwhile inserted the same tc entry we were trying
to, we re-link it creating an enless loop in the tc chain. Fix from
Daniel Borkmann.
3) There are two different WRITE bits in the MDIO address register for
the stmmac chip, depending upon the chip variant. Due to a bug we
could set them both, fix from Hock Leong Kweh.
4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
r8169: add support for RTL8168 series add-on card.
net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
openvswitch: upcall: Fix vlan handling.
ipv4: Namespaceify tcp_tw_reuse knob
net: korina: Fix NAPI versus resources freeing
net, sched: fix soft lockup in tc_classify
net/mlx4_en: Fix user prio field in XDP forward
tipc: don't send FIN message from connectionless socket
ipvlan: fix multicast processing
ipvlan: fix various issues in ipvlan_process_multicast()
In the actual implementation ether_addr_equal function tests for equality to 0
when returning. It seems in commit 0d74c4 it is somehow overlooked to change
this operator to reflect the actual function.
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The 80211.tmpl DocBook file was removed in commit 819bf59376 ("docs-rst:
sphinxify 802.11 documentation"), but the 80211.xml target was re-added to
the Makefile by commit 7ddedebb03 ("ALSA: doc: ReSTize
writing-an-alsa-driver document"), leading to a failure when building the
documentation:
*** No rule to make target 'Documentation/DocBook/80211.xml', needed by
'Documentation/DocBook/80211.aux.xml'.
cc: stable@vger.kernel.org
Signed-off-by: John Brooks <john@fastquake.com>
Mea-culpa-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Trying to initialize eMMC slot as SDIO or SD cause failure in n900 port of
qemu. eMMC itself is not detected and is not working.
Real Nokia N900 harware does not have this problem. As eMMC is really not
SDIO or SD based such change is harmless and will fix support for qemu.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 5d080aa306 ("ARM: dts: dra72: Add separate dtsi for tps65917")
added a separate dtsi for dra72-evm-tps65917 moving all the voltage supplies
to this file. But it missed adding voltage supplies to usb_phy, mmc,
dss and deleted from dra72-evm-common.dtsi. Adding the voltage supply
phandles to these nodes in dra72-evm-tps65917.dtsi
Fixes: 5d080aa306 ("ARM: dts: dra72: Add separate dtsi for tps65917")
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
USB2 port can be operated in dual-role mode but till we
have dual-role support in dwc3 driver let's limit this
port to peripheral mode.
If we don't do so it defaults to host mode. USB1 port
is meant for host only operation and we don't want
both ports in host only mode.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
VBUS detection is available on the board via the palmas PMIC.
Use extcon-palmas driver instead of extcon-gpio-usb driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Specify the power button interrupt number which is from the datasheet.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add interrupt specifiers for USB and AC charger input. Interrupt numbers
are from the datasheet.
Fix wrong property for compatible string.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Interrupt numbers are from the datasheet, so no need to keep them in
the ABI. Use the number in the DT file.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use 'interrupt-names' for getting the charger interrupt number.
Fixes: 1934e89a76 ("ARM: dts: am335x: Add the charger interrupt")
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Issue caught with static analysis tool:
"Dangerous usage of 'name' (strncpy doesn't always 0-terminate it)"
Use strlcpy _includes_ the NUL terminator, and strlcat() which ensures
that it won't overflow the buffer.
Reported-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
CC: Russell King <linux@armlinux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit 55ee7017ee ("arm: omap2: board-generic: use
omap4_local_timer_init for AM437x") unintentionally changes the
clocksource devices for AM437x from OMAP GP Timer to SyncTimer32K.
Unfortunately, the SyncTimer32K is starving from frequency deviation
as mentioned in commit 5b5c013591 ("ARM: OMAP2+: AM43x: Use gptimer
as clocksource") and, as reported by Franklin [1], even its monotonic
nature is under question (most probably there is a HW issue, but it's
still under investigation).
Taking into account above facts It's reasonable to rollback to the use
of omap3_gptimer_timer_init().
[1] http://www.spinics.net/lists/linux-omap/msg127425.html
Fixes: 55ee7017ee ("arm: omap2: board-generic: use
omap4_local_timer_init for AM437x")
Reported-by: Cooper Jr., Franklin <fcooper@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: ("ab8dd3aed011 ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
This adds the dts file into the Makefile. This should have been included in
the original patch.
V2: Update patch description - same source code
V1: Original patch
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 55871eb6e2 ("ARM: dts: dra7: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 55871eb6e2 ("ARM: dts: dra7: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 06bfb9c199 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 06bfb9c199 ("ARM: dts: dm816x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 76155b378c ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 76155b378c ("ARM: dts: dm814x: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixing the gmac4 mdio write access to use MII_GMAC4_WRITE only instead of
OR together with MII_WRITE.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip is the same as RTL8168, but its device id is 0x8161.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 73b62bd085 ("virtio-net:
remove the warning before XDP linearizing"), there's no users for
bpf_warn_invalid_xdp_buffer(), so remove it. This is a revert for
commit f23bc46c30.
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Networking stack accelerate vlan tag handling by
keeping topmost vlan header in skb. This works as
long as packet remains in OVS datapath. But during
OVS upcall vlan header is pushed on to the packet.
When such packet is sent back to OVS datapath, core
networking stack might not handle it correctly. Following
patch avoids this issue by accelerating the vlan tag
during flow key extract. This simplifies datapath by
bringing uniform packet processing for packets from
all code paths.
Fixes: 5108bbaddc ("openvswitch: add processing of L3 packets").
CC: Jarno Rajahalme <jarno@ovn.org>
CC: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespaces might have different requirements to reuse
TIME-WAIT sockets for new connections. This might be required in
cases where different namespace applications are in place which
require TIME_WAIT socket connections to be reduced independently
of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 75813028bb ("ARM: dts: am4372: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 75813028bb ("ARM: dts: am4372: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit f8bf01611c ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: f8bf01611c ("ARM: dts: am33xx: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 76a8548ea9 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 76a8548ea9 ("ARM: dts: omap5: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit da6269e7e3 ("ARM: dts: omap4: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: da6269e7e3 ("ARM: dts: omap4: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 008a2ebcd6 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.
But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.
Fixes: 008a2ebcd6 ("ARM: dts: omap3: Remove skeleton.dtsi usage")
Reported-by: Pali Rohar <pali.rohar@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Alexandre Bailon