The use of the contiguous bit by our hugetlb implementation violates
the break-before-make requirements of the architecture and can lead to
silent data corruption or TLB conflict aborts. Once again, disable these
hugetlb sizes whilst it gets worked out.
This reverts commit ab2e1b8923.
Conflicts:
arch/arm64/mm/hugetlbpage.c
Signed-off-by: Will Deacon <will.deacon@arm.com>
After 52d7523 (arm64: mm: allow the kernel to handle alignment faults on
user accesses) commit user-land accesses that produce unaligned exceptions
like in case of aarch32 ldm/stm/ldrd/strd instructions operating on
unaligned memory received by user-land as SIGSEGV. It is wrong, it should
be reported as SIGBUS as it was before 52d7523 commit.
Changed do_bad_area function to take signal and code parameters out of esr
value using fault_info table, so in case of do_alignment_fault fault
user-land will receive SIGBUS. Wrapped access to fault_info table into
esr_to_fault_info function.
Cc: <stable@vger.kernel.org>
Fixes: 52d7523 (arm64: mm: allow the kernel to handle alignment faults on user accesses)
Signed-off-by: Victor Kamensky <kamensky@cisco.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 5c492c3f52 ("arm64: smp: Add function to determine if cpus are
stuck in the kernel") added a helper function to determine if die() is
supported in cpu_ops. This function assumes a cpu will have a valid
cpu_ops entry, but that may not be the case for cpu0 is spin-table or
parking protocol is used to boot secondary cpus. In that case, there
is a NULL dereference if have_cpu_die() is called by cpu0. So add a
check for a valid cpu_ops before dereferencing it.
Fixes: 5c492c3f52 ("arm64: smp: Add function to determine if cpus are stuck in the kernel")
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- A couple of OMAP 4.11 regression fixes, including a boot regression for
SmartReflex, hypervisor mode in thumb2 mode, and reference counting of
device nodes
- A fix for cpu_idle on at91
- Minor DT fixes on across several platforms:
sunxi, bcm53xx, at91, nsp, ns2, ux500, omap
- A fix to correct an API change in the reset controllers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAWNWBrGCrR//JCVInAQJE/xAArSDx+6i7On53k3QfxkR1mONHrEOlXhlP
VbTeBfkYtYB08Pgq99QVJE5qYK2N5w2664UNbgs+KKYnYJTNl0G6EW1l7oj+21M+
xg3e6ctdfeztYeU34q7D2TxzP/EBRHdbpEuT+JHuQOWFYNfGAj2vSt2cdPUael/Q
D4s4BgeM1dIOzN3z3AvuQpqIhLedVRFAGYAaalKXiwREYUVDgnqhHCPWChVnSQMR
gnNDYcb5ZxCaELH9gkdVqyfdlScw9juKMg5v7e7KizhBUqOGBT0bguLC9Kfh3mDO
tIJGwkuqWvc5tAKuAcGklIVOzP8Wtcq0ObrFzLczy6Waf+6aaQl5J8Uw85UR/zg4
44AHzk++apXTCDlrRzQZIkvaN9TmOBr65qrW1rnqVN72FRS3arDuMV1rEFRdZy2x
riXmJmENWo+sakst4fTS0QY+/GlPDB8Md4X++Vkl3DgWFgiiBTcPbJCEazsFVip+
QQzWfXTSB98bCVUuYr5eZgMlPYHrd1ZQIbgzlzIkdUuZ4XCe4MGw88km6TqviBwf
dduNKnFctkrLAgM3V8rXZBQsZqJHRDmpOfSZ+9XtGYggy83g5FLbkp9h6Ws66SbI
KCgLzV0THCs/gKLMeDqFerO1xQzxN84pd+YKetnD1RU+5bo98DMUkqgFn+cZyCFA
dlImlZcN7Pc=
=zKIg
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
- a couple of OMAP 4.11 regression fixes, including a boot regression
for SmartReflex, hypervisor mode in thumb2 mode, and reference
counting of device nodes
- a fix for cpu_idle on at91
- minor DT fixes on across several platforms: sunxi, bcm53xx, at91,
nsp, ns2, ux500, omap
- a fix to correct an API change in the reset controllers
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
arm64: dts: NS2: Add dma-coherent to relevant DT entries
reset: fix optional reset_control_get stubs to return NULL
ARM: sun8i: a23/a33: drop bl_en_pin GPIO pinmux in reference design DTSI
ARM: dts: sun7i: lamobo-r1: Fix CPU port RGMII settings
ARM: dts: NSP: GPIO reboot open-source
ARM: at91: pm: cpu_idle: switch DDR to power-down mode
ARM: dts: add the AB8500 clocks to the device tree
ARM: dts: imx6sx-udoo-neo: Fix reboot hang
ARM: sun8i: Fix the mali clock rate
ARM: dts: BCM5301X: Correct GIC_PPI interrupt flags
ARM: dts: BCM5301X: Fix memory start address
ARM: dts: BCM5301X: Fix UARTs on bcm953012k
Revert "ARM: at91/dt: sama5d2: Use new compatible for ohci node"
ARM: OMAP2+: Release device node after it is no longer needed.
ARM: OMAP2+: Fix device node reference counts
ARM: OMAP2+: Remove legacy gpmc-nand.c
ARM: OMAP2+: gpmc-onenand: propagate error on initialization failure
ARM: dts: am335x-pcm953: Fix legacy wakeup source binding
ARM: omap2plus_defconfig: Enable INPUT_MOUSEDEV as loadable modules
ARM: dts: am57xx-idk: tpic2810 is on I2C bus, not SPI
...
please pull the following:
- Jon adds missing "dma-coherent" property to the Northstar 2 DTS include file
in order to fix both performance and cache problems for: PCIe, Ethernet,
PDC/mailbox, SATA3 and SDHCI
-----BEGIN PGP SIGNATURE-----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=5KXs
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.11/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux into fixes
Pull "Broadcom arm64 Device Tree fixes for 4.11" from Florian Fainelli:
This pull request contains Broadcom ARM64-based SoCs Device Tree fixes for 4.11,
please pull the following:
- Jon adds missing "dma-coherent" property to the Northstar 2 DTS include file
in order to fix both performance and cache problems for: PCIe, Ethernet,
PDC/mailbox, SATA3 and SDHCI
* tag 'arm-soc/for-4.11/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux:
arm64: dts: NS2: Add dma-coherent to relevant DT entries
Cache related issues with DMA rings and performance issues related to
caching are being caused by not properly setting the "dma-coherent" flag
in the device tree entries. Adding it here to correct the issue.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: fd5e5dd56 ("arm64: dts: Add PCIe0 and PCIe4 DT nodes for NS2")
Fixes: dddc3c9d7 ("arm64: dts: NS2: add AMAC ethernet support")
Fixes: e79249143 ("arm64: dts: Add Broadcom Northstar2 device tree entries for PDC driver")
Fixes: ac9aae00f ("arm64: dts: Add SATA3 AHCI and SATA3 PHY DT nodes for NS2")
Fixes: efc877676 ("arm64: dts: Add SDHCI DT node for NS2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
If kernel image extends across alignment boundary, existing
code increases the KASLR offset by size of kernel image. The
offset is masked after resizing. There are cases, where after
masking, we may still have kernel image extending across
boundary. This eventually results in only 2MB block getting
mapped while creating the page tables. This results in data aborts
while accessing unmapped regions during second relocation (with
kaslr offset) in __primary_switch. To fix this problem, round up the
kernel image size, by swapper block size, before adding it for
correction.
For example consider below case, where kernel image still crosses
1GB alignment boundary, after masking the offset, which is fixed
by rounding up kernel image size.
SWAPPER_TABLE_SHIFT = 30
Swapper using section maps with section size 2MB.
CONFIG_PGTABLE_LEVELS = 3
VA_BITS = 39
_text : 0xffffff8008080000
_end : 0xffffff800aa1b000
offset : 0x1f35600000
mask = ((1UL << (VA_BITS - 2)) - 1) & ~(SZ_2M - 1)
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
offset after existing correction (before mask) = 0x1f37f9b000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
offset (after mask) = 0x1f37e00000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
new offset w/ rounding up = 0x1f38000000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
Fixes: f80fb3a3d5 ("arm64: add support for kernel ASLR")
Cc: <stable@vger.kernel.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Hook up three pkey syscalls (which we don't implement) and the new statx
syscall, as has been done for arch/arm/.
Signed-off-by: Will Deacon <will.deacon@arm.com>
- Fix arm64 kernel boot warning when DEBUG_VIRTUAL and KASAN are enabled
- Enable KEYS_COMPAT for keyctl compat support
- Use cpus_have_const_cap() for system_uses_ttbr0_pan() (slight
performance improvement)
- Update kerneldoc for cpu_suspend() rename
- Remove the arm64-specific kprobe_exceptions_notify (weak generic
variant defined)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mCcZ
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes/cleanups from Catalin Marinas:
"In Will's absence I'm sending the arm64 fixes he queued for 4.11-rc3:
- fix arm64 kernel boot warning when DEBUG_VIRTUAL and KASAN are
enabled
- enable KEYS_COMPAT for keyctl compat support
- use cpus_have_const_cap() for system_uses_ttbr0_pan() (slight
performance improvement)
- update kerneldoc for cpu_suspend() rename
- remove the arm64-specific kprobe_exceptions_notify (weak generic
variant defined)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kernel: Update kerneldoc for cpu_suspend() rename
arm64: use const cap for system_uses_ttbr0_pan()
arm64: support keyctl() system call in 32-bit mode
arm64: kasan: avoid bad virt_to_pfn()
arm64: kprobes: remove kprobe_exceptions_notify
Pull irq fixes from Thomas Gleixner:
- a workaround for a GIC erratum
- a missing stub function for CONFIG_IRQDOMAIN=n
- fixes for a couple of type inconsistencies
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/crossbar: Fix incorrect type of register size
irqchip/gicv3-its: Add workaround for QDF2400 ITS erratum 0065
irqdomain: Add empty irq_domain_check_msi_remap
irqchip/crossbar: Fix incorrect type of local variables
ARM updates from Marc Zyngier:
"vgic updates:
- Honour disabling the ITS
- Don't deadlock when deactivating own interrupts via MMIO
- Correctly expose the lact of IRQ/FIQ bypass on GICv3
I/O virtualization:
- Make KVM_CAP_NR_MEMSLOTS big enough for large guests with
many PCIe devices
General bug fixes:
- Gracefully handle exception generated with syndroms that
the host doesn't understand
- Properly invalidate TLBs on VHE systems"
x86:
- improvements in emulation of VMCLEAR, VMX MSR bitmaps, and VCPU reset
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJYxENfAAoJEED/6hsPKofoEEkIAIWglnOGOHqf4pPv9OThKzKm
5CGINdPVEkJ56QNaYrINiQRHAzIUg8dsrhsisYmEdYGv3Mxf5WO0OebfzTrniNm4
GXIM8OuYD04MSnIomfGGBAwFZ6ptgdeD+PVkSFYHArkvWYfPm54ghjVj3AXmkicf
tRiIsPSiL/QT0vha5LBGfwsWOYavmZRfQBNA5yYUIHgO0Mp7LI24AeZOQiSM2ngx
Gl5xfzk0bayhZSBr+r/fvxqbEd0udiY7klGEvt3hrPT+JzzpoamEgCCZ6eLFZbGM
eABeQUzm7StD4Ib3WHkVU81ysOWndL0TK94BBBLIn1j+ht9FLi9iGkmTYspk9po=
=/phS
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM updates from Marc Zyngier:
- vgic updates:
- Honour disabling the ITS
- Don't deadlock when deactivating own interrupts via MMIO
- Correctly expose the lact of IRQ/FIQ bypass on GICv3
- I/O virtualization:
- Make KVM_CAP_NR_MEMSLOTS big enough for large guests with many
PCIe devices
- General bug fixes:
- Gracefully handle exception generated with syndroms that the host
doesn't understand
- Properly invalidate TLBs on VHE systems
x86:
- improvements in emulation of VMCLEAR, VMX MSR bitmaps, and VCPU
reset
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: nVMX: do not warn when MSR bitmap address is not backed
KVM: arm64: Increase number of user memslots to 512
KVM: arm/arm64: Remove KVM_PRIVATE_MEM_SLOTS definition that are unused
KVM: arm/arm64: Enable KVM_CAP_NR_MEMSLOTS on arm/arm64
KVM: Add documentation for KVM_CAP_NR_MEMSLOTS
KVM: arm/arm64: VGIC: Fix command handling while ITS being disabled
arm64: KVM: Survive unknown traps from guests
arm: KVM: Survive unknown traps from guests
KVM: arm/arm64: Let vcpu thread modify its own active state
KVM: nVMX: reset nested_run_pending if the vCPU is going to be reset
kvm: nVMX: VMCLEAR should not cause the vCPU to shut down
KVM: arm/arm64: vgic-v3: Don't pretend to support IRQ/FIQ bypass
arm64: KVM: VHE: Clear HCR_TGE when invalidating guest TLBs
Commit af391b15f7 ("arm64: kernel: rename __cpu_suspend to keep it
aligned with arm") renamed cpu_suspend() to arm_cpuidle_suspend(), but
forgot to update the kerneldoc header.
Fixes: af391b15f7 ("arm64: kernel: rename __cpu_suspend to keep it aligned with arm")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since commit 4b65a5db36 ("arm64: Introduce
uaccess_{disable,enable} functionality based on TTBR0_EL1"),
system_uses_ttbr0_pan() has used cpus_have_cap() to determine whether
PAN is present.
Since commit a4023f6827 ("arm64: Add hypervisor safe helper for
checking constant capabilities"), which was introduced around the same
time, cpus_have_cap() doesn't try to use a static key, and must always
perform a load, test, and consitional branch (likely a tbnz for the
latter two).
Elsewhere, we moved to using cpus_have_const_cap(), which can use a
static key (i.e. a non-conditional branch), which is patched at runtime
when the feature is detected.
This patch makes system_uses_ttbr0_pan() use cpus_have_const_cap(). The
static key is likely a win for hot-paths like the uacccess primitives,
and this makes our usage consistent regardless.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
As is the case for a number of other architectures that have a 32-bit
compat mode, enable KEYS_COMPAT if both COMPAT and KEYS are enabled.
This allows AArch32 programs to use the keyctl() system call when
running on an AArch64 kernel.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Booting a v4.11-rc1 kernel with DEBUG_VIRTUAL and KASAN enabled produces
the following splat (trimmed for brevity):
[ 0.000000] virt_to_phys used for non-linear address: ffff200008080000 (0xffff200008080000)
[ 0.000000] WARNING: CPU: 0 PID: 0 at arch/arm64/mm/physaddr.c:14 __virt_to_phys+0x48/0x70
[ 0.000000] PC is at __virt_to_phys+0x48/0x70
[ 0.000000] LR is at __virt_to_phys+0x48/0x70
[ 0.000000] Call trace:
[ 0.000000] [<ffff2000080b1ac0>] __virt_to_phys+0x48/0x70
[ 0.000000] [<ffff20000a03b86c>] kasan_init+0x1c0/0x498
[ 0.000000] [<ffff20000a034018>] setup_arch+0x2fc/0x948
[ 0.000000] [<ffff20000a030c68>] start_kernel+0xb8/0x570
[ 0.000000] [<ffff20000a0301e8>] __primary_switched+0x6c/0x74
This is because we use virt_to_pfn() on a kernel image address when
trying to figure out its nid, so that we can allocate its shadow from
the same node.
As with other recent changes, this patch uses lm_alias() to solve this.
We could instead use NUMA_NO_NODE, as x86 does for all shadow
allocations, though we'll likely want the "real" memory shadow to be
backed from its corresponding nid anyway, so we may as well be
consistent and find the nid for the image shadow.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit fc62d0207a ("kprobes: Introduce weak variant of
kprobe_exceptions_notify()") introduces a generic empty version of the
function for architectures that don't need special handling, like arm64.
As such, remove the arch/arm64/ specific handler.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If an architecture uses 4level-fixup.h we don't need to do anything as
it includes 5level-fixup.h.
If an architecture uses pgtable-nop*d.h, define __ARCH_USE_5LEVEL_HACK
before inclusion of the header. It makes asm-generic code to use
5level-fixup.h.
If an architecture has 4-level paging or folds levels on its own,
include 5level-fixup.h directly.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Having only 32 memslots is a real constraint for the maximum
number of PCI devices that can be assigned to a single guest.
Assuming each PCI device/virtual function having two memory BAR
regions, we could assign only 15 devices/virtual functions to a
guest.
Hence increase KVM_USER_MEM_SLOTS to 512 as done in other archs like
powerpc.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Linu Cherian <linu.cherian@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently we BUG() if we see an ESR_EL2.EC value we don't recognise. As
configurable disables/enables are added to the architecture (controlled
by RES1/RES0 bits respectively), with associated synchronous exceptions,
it may be possible for a guest to trigger exceptions with classes that
we don't recognise.
While we can't service these exceptions in a manner useful to the guest,
we can avoid bringing down the host. Per ARM DDI 0487A.k_iss10775, page
D7-1937, EC values within the range 0x00 - 0x2c are reserved for future
use with synchronous exceptions, and EC values within the range 0x2d -
0x3f may be used for either synchronous or asynchronous exceptions.
The patch makes KVM handle any unknown EC by injecting an UNDEFINED
exception into the guest, with a corresponding (ratelimited) warning in
the host dmesg. We could later improve on this with with a new (opt-in)
exit to the host userspace.
Cc: Dave Martin <dave.martin@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On Qualcomm Datacenter Technologies QDF2400 SoCs, the ITS hardware
implementation uses 16Bytes for Interrupt Translation Entry (ITE),
but reports an incorrect value of 8Bytes in GITS_TYPER.ITTE_size.
It might cause kernel memory corruption depending on the number
of MSI(x) that are configured and the amount of memory that has
been allocated for ITEs in its_create_device().
This patch fixes the potential memory corruption by setting the
correct ITE size to 16Bytes.
Cc: stable@vger.kernel.org
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When invalidating guest TLBs, special care must be taken to
actually shoot the guest TLBs and not the host ones if we're
running on a VHE system. This is controlled by the HCR_EL2.TGE
bit, which we forget to clear before invalidating TLBs.
Address the issue by introducing two wrappers (__tlb_switch_to_guest
and __tlb_switch_to_host) that take care of both the VTTBR_EL2
and HCR_EL2.TGE switching.
Reported-by: Tomasz Nowicki <tnowicki@caviumnetworks.com>
Tested-by: Tomasz Nowicki <tnowicki@caviumnetworks.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
This includes two branches for arm64 dt updates, both following up
on earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the
start of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAWLmRS2CrR//JCVInAQKrkQ//bd8TCGXA0tRwDMEGejtWChZcNkGZDaer
sNMyE/c1p5+/4euSmf3jW1JsIx4JDtjr0psKeRpgYId8GVdvaYceFbSMJl6o9hDc
pm3sqb66xEgrWQoSBA2Urz/RhSIrxkYbuTpYbN4teV9I/IFgTUggaBSzfkq3SLRE
bEVSbCw0S/6t3vJgW4CKCI75+a3NexqImvi8txNwueQQMnDLnOkG97vMUQJgDq0j
E+CeOk0mvlGF+TiVoAhUxT3YIt8azUTfUVw7CBIRvo/49sUCiETk6xie93FaC7GI
Tmg9KK+oZhrmqt8PBGkikxQMHATnKrfJbMNi/K6nrxW91ylSkwTN/7jfhSjFDrdI
4WNB2x3u6KUnQ0XOKVY36gUnV8kJ/2K9pTZpq0K7m4czo8YAid9LumvDnqhPI0Xg
fXxq3YBx7AfzsdBL3+nQ7AH3tr9Bvt01kMZwYwNgpqtglEBScAgzyrPG/yyTBFq7
KOkoyNojTaHZHcDtYqSaxYls+2tdeyvYuQJ7QGQ5DJCW99NgbRuFfIUJvgwRPoKt
13ioIJxDUHmemR6xFURWVH1dPkkqwtJht7us5jcxuxBL9ZhmEb6vophvyxj62zTZ
8A+PE3cC1azhKph7rVrUl9KEoYZzedwDaTGBNpYz1gN7DxDvWHYINEPB4bBLzYmv
uWsSYVbV2Qs=
=A3U6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
This includes two branches for arm64 dt updates, both following up on
earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the start
of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: deconfig: fix the moxart defconfig
ARM: ux500: resume the second core properly
arm64: dts: juno: update definition for programmable replicator
arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost
arm64: dts: exynos: Add USB 3.0 controller node for Exynos7
arm64: dts: exynos: Use macros for pinctrl configuration on Exynos7
pinctrl: dt-bindings: samsung: Add Exynos7 specific pinctrl macro definitions
arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e
ARM64: dts: meson-gxbb-p200: add ADC laddered keys
ARM64: dts: meson: meson-gx: add the SAR ADC
ARM64: dts: meson-gxl: add the pwm_ao_b pin
ARM64: dts: meson-gx: add the missing pwm_AO_ab node
clk: gxbb: fix CLKID_ETH defined twice
ARM64: dts: meson-gxl: rename Nexbox A95x for consistency
clk: gxbb: add the SAR ADC clocks and expose them
dt-bindings: amlogic: Add WeTek boards
ARM64: dts: meson-gxbb: Add support for WeTek Hub and Play
dt-bindings: vendor-prefix: Add wetek vendor prefix
ARM64: dts: meson-gxm: Rename q200 and q201 DT files for consistency
ARM64: dts: meson-gx: Add HDMI HPD/DDC pinctrl nodes
...
Merge "ARMv8 Juno DT fix for v4.11" from Sudeep Holla:
Just single patch to fix replicator in order to prevent overflows at
the source and reduce the back pressure by splitting the trace output
to TPIU and ETR.
* tag 'juno-fixes-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: update definition for programmable replicator
Update code that relied on sched.h including various MM types for them.
This will allow us to remove the <linux/mm_types.h> include from <linux/sched.h>.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Instead of including the full <linux/signal.h>, we are going to include the
types-only <linux/signal_types.h> header in <linux/sched.h>, to further
decouple the scheduler header from the signal headers.
This means that various files which relied on the full <linux/signal.h> need
to be updated to gain an explicit dependency on it.
Update the code that relies on sched.h's inclusion of the <linux/signal.h> header.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/task_stack.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task_stack.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/task.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/hotplug.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/hotplug.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/debug.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/debug.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split more MM APIs out of <linux/sched.h>, which
will have to be picked up from a couple of .c files.
The APIs that we are going to move are:
arch_pick_mmap_layout()
arch_get_unmapped_area()
arch_get_unmapped_area_topdown()
mm_update_next_owner()
Include the header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/topology.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/topology.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
workaround
- Revert contiguous bit support due to TLB conflict aborts in simulation
- Don't treat all CPU ID register fields as 4-bit quantities
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJYsHbpAAoJELescNyEwWM03xgH/jPZwxdS0UL1WftjqE7VXBI2
5STwLBXB8cBr527QHBY7VCbtEQZAFnij7vJ8Eqe6nA8SMDbC1RTJ2ZkiPq0rKjVg
pVJEdd3jEcRb3HNam90tOBTjlsyuR5Eagj0RI07j+YgsKhCxVTf6wu7z2StKhbuk
o8P3fbV9JA9c68JR2MR7Z2GFe2pZW0vbRrKoSx6CdoCU8Wod46BUq+P+BoeVR+vZ
593ERXnDi9tzoWFLyJYobO0PVuoipjX4e6+NxX+hPRKck6gJByainhnl63gGil9L
vavJ2r3GK4pO5qAsusx6eXQksyR9lX5tGPk7XgJi+M+WMd4Moe+/zNXd4NADGww=
=aG7Y
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The main fix here addresses a kernel panic triggered on Qualcomm
QDF2400 due to incorrect register usage in an erratum workaround
introduced during the merge window.
Summary:
- Fix kernel panic on specific Qualcomm platform due to broken
erratum workaround
- Revert contiguous bit support due to TLB conflict aborts in
simulation
- Don't treat all CPU ID register fields as 4-bit quantities"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/cpufeature: check correct field width when updating sys_val
Revert "arm64: mm: set the contiguous bit for kernel mappings where appropriate"
arm64: Avoid clobbering mm in erratum workaround on QDF2400
Apart from adding the helper function itself, the rest of the kernel is
converted mechanically using:
git grep -l 'atomic_inc.*mm_count' | xargs sed -i 's/atomic_inc(&\(.*\)->mm_count);/mmgrab\(\1\);/'
git grep -l 'atomic_inc.*mm_count' | xargs sed -i 's/atomic_inc(&\(.*\)\.mm_count);/mmgrab\(\&\1\);/'
This is needed for a later patch that hooks into the helper, but might
be a worthwhile cleanup on its own.
(Michal Hocko provided most of the kerneldoc comment.)
Link: http://lkml.kernel.org/r/20161218123229.22952-1-vegard.nossum@oracle.com
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
overwritting||overwriting
Link: http://lkml.kernel.org/r/1481573103-11329-29-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Often all is needed is these small helpers, instead of compiler.h or a
full kprobes.h. This is important for asm helpers, in fact even some
asm/kprobes.h make use of these helpers... instead just keep a generic
asm file with helpers useful for asm code with the least amount of
clutter as possible.
Likewise we need now to also address what to do about this file for both
when architectures have CONFIG_HAVE_KPROBES, and when they do not. Then
for when architectures have CONFIG_HAVE_KPROBES but have disabled
CONFIG_KPROBES.
Right now most asm/kprobes.h do not have guards against CONFIG_KPROBES,
this means most architecture code cannot include asm/kprobes.h safely.
Correct this and add guards for architectures missing them.
Additionally provide architectures that not have kprobes support with
the default asm-generic solution. This lets us force asm/kprobes.h on
the header include/linux/kprobes.h always, but most importantly we can
now safely include just asm/kprobes.h on architecture code without
bringing the full kitchen sink of header files.
Two architectures already provided a guard against CONFIG_KPROBES on its
kprobes.h: sh, arch. The rest of the architectures needed gaurds added.
We avoid including any not-needed headers on asm/kprobes.h unless
kprobes have been enabled.
In a subsequent atomic change we can try now to remove compiler.h from
include/linux/kprobes.h.
During this sweep I've also identified a few architectures defining a
common macro needed for both kprobes and ftrace, that of the definition
of the breakput instruction up. Some refer to this as
BREAKPOINT_INSTRUCTION. This must be kept outside of the #ifdef
CONFIG_KPROBES guard.
[mcgrof@kernel.org: fix arm64 build]
Link: http://lkml.kernel.org/r/CAB=NE6X1WMByuARS4mZ1g9+W=LuVBnMDnh_5zyN0CLADaVh=Jw@mail.gmail.com
[sfr@canb.auug.org.au: fixup for kprobes declarations moving]
Link: http://lkml.kernel.org/r/20170214165933.13ebd4f4@canb.auug.org.au
Link: http://lkml.kernel.org/r/20170203233139.32682-1-mcgrof@kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes
it was possible to remove the IB DMA mapping code entirely and
switch the RDMA stack to use the core DMA mapping code. This resulted
in a nice set of cleanups, but touched the entire tree. This branch
will be submitted separately to Linus at the end of the merge window
as per normal practice for tree wide changes like this.
-----BEGIN PGP SIGNATURE-----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=e0Si
-----END PGP SIGNATURE-----
Merge tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma DMA mapping updates from Doug Ledford:
"Drop IB DMA mapping code and use core DMA code instead.
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes it
was possible to remove the IB DMA mapping code entirely and switch the
RDMA stack to use the core DMA mapping code.
This resulted in a nice set of cleanups, but touched the entire tree
and has been kept separate for that reason."
* tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
IB/rxe, IB/rdmavt: Use dma_virt_ops instead of duplicating it
IB/core: Remove ib_device.dma_device
nvme-rdma: Switch from dma_device to dev.parent
RDS: net: Switch from dma_device to dev.parent
IB/srpt: Modify a debug statement
IB/srp: Switch from dma_device to dev.parent
IB/iser: Switch from dma_device to dev.parent
IB/IPoIB: Switch from dma_device to dev.parent
IB/rxe: Switch from dma_device to dev.parent
IB/vmw_pvrdma: Switch from dma_device to dev.parent
IB/usnic: Switch from dma_device to dev.parent
IB/qib: Switch from dma_device to dev.parent
IB/qedr: Switch from dma_device to dev.parent
IB/ocrdma: Switch from dma_device to dev.parent
IB/nes: Remove a superfluous assignment statement
IB/mthca: Switch from dma_device to dev.parent
IB/mlx5: Switch from dma_device to dev.parent
IB/mlx4: Switch from dma_device to dev.parent
IB/i40iw: Remove a superfluous assignment statement
IB/hns: Switch from dma_device to dev.parent
...
The callers of the DMA alloc functions already provide the proper
context GFP flags. Make sure to pass them through to the CMA allocator,
to make the CMA compaction context aware.
Link: http://lkml.kernel.org/r/20170127172328.18574-3-l.stach@pengutronix.de
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Radim Krcmar <rkrcmar@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Alexander Graf <agraf@suse.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we're updating a register's sys_val, we use arm64_ftr_value() to
find the new field value. We use cpuid_feature_extract_field() to find
the new value, but this implicitly assumes a 4-bit field, so we may
extract more bits than we mean to for fields like CTR_EL0.L1ip.
This affects update_cpu_ftr_reg(), where we may extract erroneous values
for ftr_cur and ftr_new. Depending on the additional bits extracted in
either case, we may erroneously detect that the value is mismatched, and
we'll try to compute a new safe value.
Dependent on these extra bits and feature type, arm64_ftr_safe_value()
may pessimistically select the always-safe value, or may erroneously
choose either the extracted cur or new value as the safe option. The
extra bits will subsequently be masked out in arm64_ftr_set_value(), so
we may choose a higher value, yet write back a lower one.
Fix this by passing the width down explicitly in arm64_ftr_value(), so
we always extract the correct amount.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This reverts commit 0bfc445dec.
When we change the permissions of regions mapped using contiguous
entries, the architecture requires us to follow a Break-Before-Make
strategy, breaking *all* associated entries before we can change any of
the following properties from the entries:
- presence of the contiguous bit
- output address
- attributes
- permissiones
Failure to do so can result in a number of problems (e.g. TLB conflict
aborts and/or erroneous results from TLB lookups).
See ARM DDI 0487A.k_iss10775, "Misprogramming of the Contiguous bit",
page D4-1762.
We do not take this into account when altering the permissions of kernel
segments in mark_rodata_ro(), where we change the permissions of live
contiguous entires one-by-one, leaving them transiently inconsistent.
This has been observed to result in failures on some fast model
configurations.
Unfortunately, we cannot follow Break-Before-Make here as we'd have to
unmap kernel text and data used to perform the sequence.
For the timebeing, revert commit 0bfc445dec so as to avoid issues
resulting from this misuse of the contiguous bit.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <Will.Deacon@arm.com>
Cc: stable@vger.kernel.org # v4.10
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 38fd94b027 ("arm64: Work around Falkor erratum 1003") tried to
work around a hardware erratum, but actually caused a system crash of
its own during switch_mm:
cpu_do_switch_mm+0x20/0x40
efi_virtmap_load+0x34/0x40
virt_efi_get_next_variable+0x64/0xc8
efivar_init+0x8c/0x348
efisubsys_init+0xd4/0x270
do_one_initcall+0x80/0x110
kernel_init_freeable+0x19c/0x240
kernel_init+0x10/0x100
ret_from_fork+0x10/0x50
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
In cpu_do_switch_mm, x1 contains the mm_struct pointer, which needs to
be preserved by the pre_ttbr0_update_workaround macro rather than passed
as a temporary.
This patch clobbers x2 and x3 instead, keeping the mm_struct intact
after the workaround has run.
Fixes: 38fd94b027 ("arm64: Work around Falkor erratum 1003")
Tested-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM64 DT updates are fairly small this time, only two new SoCs and a handful
of new machines get added, all of them similar to other hardware we already
support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner: MMC, USB
ARM Juno: Coresight, STM
Broadcom: NS2 GICv2m irqchip and PCIe
Marvell: Armada 3700 SPI, I2C, ethernet switch
Mediatek: MT8173 thermal
NXP i.MX: LS1046A thermal
Qualcomm: coresight on MSM8916, HDMI, WCNSS, SCM
Renesas: r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip: thermal, eDP, pinctrl enhancements
Samsung: TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier: SD reset, eMMC controller
ZTE: oppv2 cpufreq
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=glug
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"ARM64 DT updates are fairly small this time, only two new SoCs and a
handful of new machines get added, all of them similar to other
hardware we already support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards:
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64:
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K:
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner:
- MMC, USB
ARM Juno:
- Coresight, STM
Broadcom:
- NS2 GICv2m irqchip and PCIe
Marvell:
- Armada 3700 SPI, I2C, ethernet switch
Mediatek:
- MT8173 thermal
NXP i.MX:
- LS1046A thermal
Qualcomm:
- coresight on MSM8916, HDMI, WCNSS, SCM
Renesas:
- r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip:
- thermal, eDP, pinctrl enhancements
Samsung:
- TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier:
- SD reset, eMMC controller
ZTE:
- oppv2 cpufreq"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (110 commits)
arm64: dts: qcom: Add msm8916 CoreSight components
arm64: dts: marvell: adjust name of sd-mmc-gop clock in syscon
arm64: allwinner: add BananaPi-M64 support
arm64: allwinner: a64: add UART1 pin nodes
arm64: allwinner: pine64: add MMC support
arm64: allwinner: a64: Increase the MMC max frequency
arm64: allwinner: a64: Add MMC pinctrl nodes
arm64: allwinner: a64: Add MMC nodes
dt-bindings: clockgen: Add compatible string for LS1012A
Documentation: DT: add LS1012A compatible for SCFG and DCFG
Documentation: DT: Add entry for FSL LS1012A RDB, FRDM, QDS boards
arm64: dts: marvell: add generic-ahci compatibles for CP110 ahci
arm64: tegra: Use symbolic reset identifiers
arm64: dts: r8a7796: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: tidyup audma definition order
arm64: dts: r8a7796: Link ARM GIC to clock and clock domain
arm64: dts: r8a7795: Link ARM GIC to clock and clock domain
arm64: dts: r8a7796: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add R-Car Gen3 thermal support
...
Defconfig additions, removals, etc. Almost all of them just turn on
drivers that we want on some platform, usually after the driver
has been merged into mainline.
There is now a new defconfig file for tango4.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=noKQ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Arnd Bergmann:
"Defconfig additions, removals, etc. Almost all of them just turn on
drivers that we want on some platform, usually after the driver has
been merged into mainline.
There is now a new defconfig file for tango4"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: multi_v7_defconfig: enable pstore configs
ARM: multi_v7_defconfig: enable some newly added crypto modules
ARM: davinci_all_defconfig: enable SATA modules
arm64: defconfig: enable CONFIG_MTD_NAND and CONFIG_MTD_NAND_DENALI_DT
arm64: defconfig: enable CONFIG_MTD_BLOCK
ARM: Import tango4_defconfig
ARM: omap2plus_defconfig: Enable support for RTC M41T80
ARM: omap2plus_defconfig: Enable support for micrell phys
ARM: vf610m4: defconfig: enable EXT4 filesystem
ARM: omap2plus_defconfig: Fix probe errors on UARTs 5 and 6
arm64: defconfig: Enable NUMA and NUMA_BALANCING
arm64: defconfig: enable SMMUv3 config
ARM: davinci_all_defconfig: enable iio
ARM: Keystone: Enable ARCH_HAS_RESET_CONTROLLER
ARM: configs: stm32: Add RTC support in STM32 defconfig
ARM: defconfig: qcom: add APQ8060 DragonBoard devices
ARM: qcom_defconfig: enable thermal sensors
ARM: qcom_defconfig: add ahci configs
ARM: qcom_defconfig: add pcie and atl1c ethernet configs
ARM: qcom_defconfig: add usb related configs
...
Changes to platform code for 64-bit ARM platforms, only trivial
stuff this time, a few defconfig changes to enable drivers, and
a new entry for the Cavium ThunderX2 platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ymi+
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit updates from Arnd Bergmann:
"Changes to platform code for 64-bit ARM platforms, only trivial stuff
this time, a few defconfig changes to enable drivers, and a new entry
for the Cavium ThunderX2 platform"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add Cavium ThunderX2 entry
arm64: add ARCH_THUNDER2 to defconfig
arm64: add THUNDER2 processor family
MAINTAINERS: Extend ARM/Mediatek SoC support section
arm64: defconfig: enable CONFIG_MMC_SDHCI_CADENCE
arm64: defconfig: enable XORv2 for Marvell Armada 7K/8K
Will Deacon