dax_clear_blocks is currently performing a cond_resched() after every
PAGE_SIZE memset. We need not check so frequently, for example md-raid
only calls cond_resched() at stripe granularity. Also, in preparation
for introducing a dax_map_atomic() operation that temporarily pins a dax
mapping move the call to cond_resched() to the outer loop.
The worst case latency between calls to cond_resched() after this change
is 500us the average latency is 133us. This is up from a 10us max and
4us average.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jan Kara <jack@suse.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To date, we have implemented two I/O usage models for persistent memory,
PMEM (a persistent "ram disk") and DAX (mmap persistent memory into
userspace). This series adds a third, DAX-GUP, that allows DAX mappings
to be the target of direct-i/o. It allows userspace to coordinate
DMA/RDMA from/to persistent memory.
The implementation leverages the ZONE_DEVICE mm-zone that went into
4.3-rc1 (also discussed at kernel summit) to flag pages that are owned
and dynamically mapped by a device driver. The pmem driver, after
mapping a persistent memory range into the system memmap via
devm_memremap_pages(), arranges for DAX to distinguish pfn-only versus
page-backed pmem-pfns via flags in the new pfn_t type.
The DAX code, upon seeing a PFN_DEV+PFN_MAP flagged pfn, flags the
resulting pte(s) inserted into the process page tables with a new
_PAGE_DEVMAP flag. Later, when get_user_pages() is walking ptes it keys
off _PAGE_DEVMAP to pin the device hosting the page range active.
Finally, get_page() and put_page() are modified to take references
against the device driver established page mapping.
Finally, this need for "struct page" for persistent memory requires
memory capacity to store the memmap array. Given the memmap array for a
large pool of persistent may exhaust available DRAM introduce a
mechanism to allocate the memmap from persistent memory. The new
"struct vmem_altmap *" parameter to devm_memremap_pages() enables
arch_add_memory() to use reserved pmem capacity rather than the page
allocator.
This patch (of 25):
Both __dax_pmd_fault, and clear_pmem() were taking special steps to
clear memory a page at a time to take advantage of non-temporal
clear_page() implementations. However, x86_64 does not use non-temporal
instructions for clear_page(), and arch_clear_pmem() was always
incurring the cost of __arch_wb_cache_pmem().
Clean up the assumption that doing clear_pmem() a page at a time is more
performant.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jan Kara <jack@suse.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let's define page_mapped() to be true for compound pages if any
sub-pages of the compound page is mapped (with PMD or PTE).
On other hand page_mapcount() return mapcount for this particular small
page.
This will make cases like page_get_anon_vma() behave correctly once we
allow huge pages to be mapped with PTE.
Most users outside core-mm should use page_mapcount() instead of
page_mapped().
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The goal of this patchset is to make refcounting on THP pages cheaper
with simpler semantics and allow the same THP compound page to be mapped
with PMD and PTEs. This is required to get reasonable THP-pagecache
implementation.
With the new refcounting design it's much easier to protect against
split_huge_page(): simple reference on a page will make you the deal.
It makes gup_fast() implementation simpler and doesn't require
special-case in futex code to handle tail THP pages.
It should improve THP utilization over the system since splitting THP in
one process doesn't necessary lead to splitting the page in all other
processes have the page mapped.
The patchset drastically lower complexity of get_page()/put_page()
codepaths. I encourage people look on this code before-and-after to
justify time budget on reviewing this patchset.
This patch (of 37):
With new refcounting all subpages of the compound page are not necessary
have the same mapcount. We need to take into account mapcount of every
sub-page.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lock_page() must operate on the whole compound page. It doesn't make
much sense to lock part of compound page. Change code to use head
page's PG_locked, if tail page is passed.
This patch also gets rid of custom helper functions --
__set_page_locked() and __clear_page_locked(). They are replaced with
helpers generated by __SETPAGEFLAG/__CLEARPAGEFLAG. Tail pages to these
helper would trigger VM_BUG_ON().
SLUB uses PG_locked as a bit spin locked. IIUC, tail pages should never
appear there. VM_BUG_ON() is added to make sure that this assumption is
correct.
[akpm@linux-foundation.org: fix fs/cifs/file.c]
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Jérôme Glisse <jglisse@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kerberized NFSv4.1 mounts, and Scott Mayhew's work addressing ACK storms
that can affect some high-availability NFS setups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=G7V3
-----END PGP SIGNATURE-----
Merge tag 'nfsd-4.5' of git://linux-nfs.org/~bfields/linux
Pull nfsd updates from Bruce Fields:
"Smaller bugfixes and cleanup, including a fix for a failures of
kerberized NFSv4.1 mounts, and Scott Mayhew's work addressing ACK
storms that can affect some high-availability NFS setups"
* tag 'nfsd-4.5' of git://linux-nfs.org/~bfields/linux:
nfsd: add new io class tracepoint
nfsd: give up on CB_LAYOUTRECALLs after two lease periods
nfsd: Fix nfsd leaks sunrpc module references
lockd: constify nlmsvc_binding structure
lockd: use to_delayed_work
nfsd: use to_delayed_work
Revert "svcrdma: Do not send XDR roundup bytes for a write chunk"
lockd: Register callbacks on the inetaddr_chain and inet6addr_chain
nfsd: Register callbacks on the inetaddr_chain and inet6addr_chain
sunrpc: Add a function to close temporary transports immediately
nfsd: don't base cl_cb_status on stale information
nfsd4: fix gss-proxy 4.1 mounts for some AD principals
nfsd: fix unlikely NULL deref in mach_creds_match
nfsd: minor consolidation of mach_cred handling code
nfsd: helper for dup of possibly NULL string
svcrpc: move some initialization to common code
nfsd: fix a warning message
nfsd: constify nfsd4_callback_ops structure
nfsd: recover: constify nfsd4_client_tracking_ops structures
svcrdma: Do not send XDR roundup bytes for a write chunk
Pull UDF fixes and quota cleanups from Jan Kara:
"Several UDF fixes and some minor quota cleanups"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Check output buffer length when converting name to CS0
udf: Prevent buffer overrun with multi-byte characters
quota: constify qtree_fmt_operations structures
udf: avoid uninitialized variable use
udf: Fix lost indirect extent block
udf: Factor out code for creating indirect extent
udf: limit the maximum number of indirect extents in a row
udf: limit the maximum number of TD redirections
fs: make quota/dquot.c explicitly non-modular
fs: make quota/netlink.c explicitly non-modular
Merge first patch-bomb from Andrew Morton:
- A few hotfixes which missed 4.4 becasue I was asleep. cc'ed to
-stable
- A few misc fixes
- OCFS2 updates
- Part of MM. Including pretty large changes to page-flags handling
and to thp management which have been buffered up for 2-3 cycles now.
I have a lot of MM material this time.
[ It turns out the THP part wasn't quite ready, so that got dropped from
this series - Linus ]
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (117 commits)
zsmalloc: reorganize struct size_class to pack 4 bytes hole
mm/zbud.c: use list_last_entry() instead of list_tail_entry()
zram/zcomp: do not zero out zcomp private pages
zram: pass gfp from zcomp frontend to backend
zram: try vmalloc() after kmalloc()
zram/zcomp: use GFP_NOIO to allocate streams
mm: add tracepoint for scanning pages
drivers/base/memory.c: fix kernel warning during memory hotplug on ppc64
mm/page_isolation: use macro to judge the alignment
mm: fix noisy sparse warning in LIBCFS_ALLOC_PRE()
mm: rework virtual memory accounting
include/linux/memblock.h: fix ordering of 'flags' argument in comments
mm: move lru_to_page to mm_inline.h
Documentation/filesystems: describe the shared memory usage/accounting
memory-hotplug: don't BUG() in register_memory_resource()
hugetlb: make mm and fs code explicitly non-modular
mm/swapfile.c: use list_for_each_entry_safe in free_swap_count_continuations
mm: /proc/pid/clear_refs: no need to clear VM_SOFTDIRTY in clear_soft_dirty_pmd()
mm: make sure isolate_lru_page() is never called for tail page
vmstat: make vmstat_updater deferrable again and shut down on idle
...
I managed to trigger this:
| INFO: trying to register non-static key.
| the code is fine but needs lockdep annotation.
| turning off the locking correctness validator.
| CPU: 1 PID: 781 Comm: systemd-gpt-aut Not tainted 4.4.0-rt2+ #14
| Hardware name: ARM-Versatile Express
| [<80307cec>] (dump_stack)
| [<80070e98>] (__lock_acquire)
| [<8007184c>] (lock_acquire)
| [<80287800>] (btrfs_ioctl)
| [<8012a8d4>] (do_vfs_ioctl)
| [<8012ac14>] (SyS_ioctl)
so I think that btrfs_device_data_ordered_init() is not invoked behind
a macro somewhere.
Fixes: 7cc8e58d53 ("Btrfs: fix unprotected device's variants on 32bits machine")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If we return 1 here, then the caller treats it as an error and returns
-EINVAL. It causes a static checker warning to treat positive returns
as an error.
Fixes: 1aba86d67f ('Btrfs: fix easily get into ENOSPC in mixed case')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Fix the following error:
fs/btrfs/backref.c:565:1-20: iterator with update on line 577
Fixes: a7ca422('btrfs: use list_for_each_entry* in backref.c')
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The compression message might not be correctly output.
Fix it.
[[before fix]]
# mount -o compress /dev/sdb3 /test3
[ 996.874264] BTRFS info (device sdb3): disk space caching is enabled
[ 996.874268] BTRFS: has skinny extents
# mount | grep /test3
/dev/sdb3 on /test3 type btrfs (rw,relatime,compress=zlib,space_cache,subvolid=5,subvol=/)
# mount -o remount,compress-force /dev/sdb3 /test3
[ 1035.075017] BTRFS info (device sdb3): force zlib compression
[ 1035.075021] BTRFS info (device sdb3): disk space caching is enabled
# mount | grep /test3
/dev/sdb3 on /test3 type btrfs (rw,relatime,compress-force=zlib,space_cache,subvolid=5,subvol=/)
# mount -o remount,compress /dev/sdb3 /test3
[ 1053.679092] BTRFS info (device sdb3): disk space caching is enabled
# mount | grep /test3
/dev/sdb3 on /test3 type btrfs (rw,relatime,compress=zlib,space_cache,subvolid=5,subvol=/)
[[after fix]]
# mount -o compress /dev/sdb3 /test3
[ 401.021753] BTRFS info (device sdb3): use zlib compression
[ 401.021758] BTRFS info (device sdb3): disk space caching is enabled
[ 401.021760] BTRFS: has skinny extents
# mount | grep /test3
/dev/sdb3 on /test3 type btrfs (rw,relatime,compress=zlib,space_cache,subvolid=5,subvol=/)
# mount -o remount,compress-force /dev/sdb3 /test3
[ 439.824624] BTRFS info (device sdb3): force zlib compression
[ 439.824629] BTRFS info (device sdb3): disk space caching is enabled
# mount | grep /test3
/dev/sdb3 on /test3 type btrfs (rw,relatime,compress-force=zlib,space_cache,subvolid=5,subvol=/)
# mount -o remount,compress /dev/sdb3 /test3
[ 459.918430] BTRFS info (device sdb3): use zlib compression
[ 459.918434] BTRFS info (device sdb3): disk space caching is enabled
# mount | grep /test3
/dev/sdb3 on /test3 type btrfs (rw,relatime,compress=zlib,space_cache,subvolid=5,subvol=/)
Signed-off-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The following call trace is seen when btrfs/031 test is executed in a loop,
[ 158.661848] ------------[ cut here ]------------
[ 158.662634] WARNING: CPU: 2 PID: 890 at /home/chandan/repos/linux/fs/btrfs/ioctl.c:558 create_subvol+0x3d1/0x6ea()
[ 158.664102] BTRFS: Transaction aborted (error -2)
[ 158.664774] Modules linked in:
[ 158.665266] CPU: 2 PID: 890 Comm: btrfs Not tainted 4.4.0-rc6-g511711a #2
[ 158.666251] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
[ 158.667392] ffffffff81c0a6b0 ffff8806c7c4f8e8 ffffffff81431fc8 ffff8806c7c4f930
[ 158.668515] ffff8806c7c4f920 ffffffff81051aa1 ffff880c85aff000 ffff8800bb44d000
[ 158.669647] ffff8808863b5c98 0000000000000000 00000000fffffffe ffff8806c7c4f980
[ 158.670769] Call Trace:
[ 158.671153] [<ffffffff81431fc8>] dump_stack+0x44/0x5c
[ 158.671884] [<ffffffff81051aa1>] warn_slowpath_common+0x81/0xc0
[ 158.672769] [<ffffffff81051b27>] warn_slowpath_fmt+0x47/0x50
[ 158.673620] [<ffffffff813bc98d>] create_subvol+0x3d1/0x6ea
[ 158.674440] [<ffffffff813777c9>] btrfs_mksubvol.isra.30+0x369/0x520
[ 158.675376] [<ffffffff8108a4aa>] ? percpu_down_read+0x1a/0x50
[ 158.676235] [<ffffffff81377a81>] btrfs_ioctl_snap_create_transid+0x101/0x180
[ 158.677268] [<ffffffff81377b52>] btrfs_ioctl_snap_create+0x52/0x70
[ 158.678183] [<ffffffff8137afb4>] btrfs_ioctl+0x474/0x2f90
[ 158.678975] [<ffffffff81144b8e>] ? vma_merge+0xee/0x300
[ 158.679751] [<ffffffff8115be31>] ? alloc_pages_vma+0x91/0x170
[ 158.680599] [<ffffffff81123f62>] ? lru_cache_add_active_or_unevictable+0x22/0x70
[ 158.681686] [<ffffffff813d99cf>] ? selinux_file_ioctl+0xff/0x1d0
[ 158.682581] [<ffffffff8117b791>] do_vfs_ioctl+0x2c1/0x490
[ 158.683399] [<ffffffff813d3cde>] ? security_file_ioctl+0x3e/0x60
[ 158.684297] [<ffffffff8117b9d4>] SyS_ioctl+0x74/0x80
[ 158.685051] [<ffffffff819b2bd7>] entry_SYSCALL_64_fastpath+0x12/0x6a
[ 158.685958] ---[ end trace 4b63312de5a2cb76 ]---
[ 158.686647] BTRFS: error (device loop0) in create_subvol:558: errno=-2 No such entry
[ 158.709508] BTRFS info (device loop0): forced readonly
[ 158.737113] BTRFS info (device loop0): disk space caching is enabled
[ 158.738096] BTRFS error (device loop0): Remounting read-write after error is not allowed
[ 158.851303] BTRFS error (device loop0): cleaner transaction attach returned -30
This occurs because,
Mount filesystem
Create subvol with ID 257
Unmount filesystem
Mount filesystem
Delete subvol with ID 257
btrfs_drop_snapshot()
Add root corresponding to subvol 257 into
btrfs_transaction->dropped_roots list
Create new subvol (i.e. create_subvol())
257 is returned as the next free objectid
btrfs_read_fs_root_no_name()
Finds the btrfs_root instance corresponding to the old subvol with ID 257
in btrfs_fs_info->fs_roots_radix.
Returns error since btrfs_root_item->refs has the value of 0.
To fix the issue the commit initializes tree root's and subvolume root's
highest_objectid when loading the roots from disk.
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Overloading extent_map->bdev to struct map_lookup * might have started out
as a means to an end, but it's a pattern that's used all over the place
now. Let's get rid of the casting and just add a union instead.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
floppy: make local variable non-static
exynos: fixes an incorrect header guard
dt-bindings: fixes some incorrect header guards
cpufreq-dt: correct dead link in documentation
cpufreq: ARM big LITTLE: correct dead link in documentation
treewide: Fix typos in printk
Documentation: filesystem: Fix typo in fs/eventfd.c
fs/super.c: use && instead of & for warn_on condition
Documentation: fix sysfs-ptp
lib: scatterlist: fix Kconfig description
Highlights include:
Stable fixes:
- Fix a regression in the SunRPC socket polling code
- Fix the attribute cache revalidation code
- Fix race in __update_open_stateid()
- Fix an lo->plh_block_lgets imbalance in layoutreturn
- Fix an Oopsable typo in ff_mirror_match_fh()
Features:
- pNFS layout recall performance improvements.
- pNFS/flexfiles: Support server-supplied layoutstats sampling period
Bugfixes + cleanups:
- NFSv4: Don't perform cached access checks before we've OPENed the file
- Fix starvation issues with background flushes
- Reclaim writes should be flushed as unstable writes if there are already
entries in the commit lists
- Various bugfixes from Chuck to fix NFS/RDMA send queue ordering problems
- Ensure that we propagate fatal layoutget errors back to the application
- Fixes for sundry flexfiles layoutstats bugs
- Fix files/flexfiles to not cache invalidated layouts in the DS commit buckets
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RBmi
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.5-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Stable fixes:
- Fix a regression in the SunRPC socket polling code
- Fix the attribute cache revalidation code
- Fix race in __update_open_stateid()
- Fix an lo->plh_block_lgets imbalance in layoutreturn
- Fix an Oopsable typo in ff_mirror_match_fh()
Features:
- pNFS layout recall performance improvements.
- pNFS/flexfiles: Support server-supplied layoutstats sampling period
Bugfixes + cleanups:
- NFSv4: Don't perform cached access checks before we've OPENed the
file
- Fix starvation issues with background flushes
- Reclaim writes should be flushed as unstable writes if there are
already entries in the commit lists
- Various bugfixes from Chuck to fix NFS/RDMA send queue ordering
problems
- Ensure that we propagate fatal layoutget errors back to the
application
- Fixes for sundry flexfiles layoutstats bugs
- Fix files/flexfiles to not cache invalidated layouts in the DS
commit buckets"
* tag 'nfs-for-4.5-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (68 commits)
NFS: Fix a compile warning about unused variable in nfs_generic_pg_pgios()
NFSv4: Fix a compile warning about no prototype for nfs4_ioctl()
NFS: Use wait_on_atomic_t() for unlock after readahead
SUNRPC: Fixup socket wait for memory
NFSv4.1/pNFS: Cleanup constify struct pnfs_layout_range arguments
NFSv4.1/pnfs: Cleanup copying of pnfs_layout_range structures
NFSv4.1/pNFS: Cleanup pnfs_mark_matching_lsegs_invalid()
NFSv4.1/pNFS: Fix a race in initiate_file_draining()
NFSv4.1/pNFS: pnfs_error_mark_layout_for_return() must always return layout
NFSv4.1/pNFS: pnfs_mark_matching_lsegs_return() should set the iomode
NFSv4.1/pNFS: Use nfs4_stateid_copy for copying stateids
NFSv4.1/pNFS: Don't pass stateids by value to pnfs_send_layoutreturn()
NFS: Relax requirements in nfs_flush_incompatible
NFSv4.1/pNFS: Don't queue up a new commit if the layout segment is invalid
NFS: Allow multiple commit requests in flight per file
NFS/pNFS: Fix up pNFS write reschedule layering violations and bugs
SUNRPC: Fix a missing break in rpc_anyaddr()
pNFS/flexfiles: Fix an Oopsable typo in ff_mirror_match_fh()
NFS: Fix attribute cache revalidation
NFS: Ensure we revalidate attributes before using execute_ok()
...
Pull vfs fix from Al Viro:
"Don't put symlink bodies in pagecache into highmem"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Make sure that highmem pages are not added to symlink page cache
When inspecting a vague code inside prctl(PR_SET_MM_MEM) call (which
testing the RLIMIT_DATA value to figure out if we're allowed to assign
new @start_brk, @brk, @start_data, @end_data from mm_struct) it's been
commited that RLIMIT_DATA in a form it's implemented now doesn't do
anything useful because most of user-space libraries use mmap() syscall
for dynamic memory allocations.
Linus suggested to convert RLIMIT_DATA rlimit into something suitable
for anonymous memory accounting. But in this patch we go further, and
the changes are bundled together as:
* keep vma counting if CONFIG_PROC_FS=n, will be used for limits
* replace mm->shared_vm with better defined mm->data_vm
* account anonymous executable areas as executable
* account file-backed growsdown/up areas as stack
* drop struct file* argument from vm_stat_account
* enforce RLIMIT_DATA for size of data areas
This way code looks cleaner: now code/stack/data classification depends
only on vm_flags state:
VM_EXEC & ~VM_WRITE -> code (VmExe + VmLib in proc)
VM_GROWSUP | VM_GROWSDOWN -> stack (VmStk)
VM_WRITE & ~VM_SHARED & !stack -> data (VmData)
The rest (VmSize - VmData - VmStk - VmExe - VmLib) could be called
"shared", but that might be strange beast like readonly-private or VM_IO
area.
- RLIMIT_AS limits whole address space "VmSize"
- RLIMIT_STACK limits stack "VmStk" (but each vma individually)
- RLIMIT_DATA now limits "VmData"
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Kees Cook <keescook@google.com>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: Pavel Emelyanov <xemul@virtuozzo.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Kconfig currently controlling compilation of this code is:
config HUGETLBFS
bool "HugeTLB file system support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that when
reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular case,
the init ordering gets moved to earlier levels when we use the more
appropriate initcalls here.
Originally I had the fs part and the mm part as separate commits, just
by happenstance of the nature of how I detected these non-modular use
cases. But that can possibly introduce regressions if the patch merge
ordering puts the fs part 1st -- as the 0-day testing reported a splat
at mount time.
Investigating with "initcall_debug" showed that the delta was
init_hugetlbfs_fs being called _before_ hugetlb_init instead of after. So
both the fs change and the mm change are here together.
In addition, it worked before due to luck of link order, since they were
both in the same initcall category. So we now have the fs part using
fs_initcall, and the mm part using subsys_initcall, which puts it one
bucket earlier. It now passes the basic sanity test that failed in
earlier 0-day testing.
We delete the MODULE_LICENSE tag and capture that information at the top
of the file alongside author comments, etc.
We don't replace module.h with init.h since the file already has that.
Also note that MODULE_ALIAS is a no-op for non-modular code.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reported-by: kernel test robot <ying.huang@linux.intel.com>
Cc: Nadia Yvette Chambers <nyc@holomorphy.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
clear_soft_dirty_pmd() is called by clear_refs_write(CLEAR_REFS_SOFT_DIRTY),
VM_SOFTDIRTY was already cleared before walk_page_range().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MemAvailable item in /proc/meminfo is to give users a hint of how
much memory is allocatable without causing swapping, so it excludes the
zones' low watermarks as unavailable to userspace.
However, for a userspace allocation, kswapd will actually reclaim until
the free pages hit a combination of the high watermark and the page
allocator's lowmem protection that keeps a certain amount of DMA and
DMA32 memory from userspace as well.
Subtract the full amount we know to be unavailable to userspace from the
number of free pages when calculating MemAvailable.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bdev_write_page() is used by swapout and by writepage where we cannot
use __GFP_FS or __GFP_IO. So it is misleading to mention GFP_KERNEL
here.
blk_queue_enter() only actually looks at __GFP_DIRECT_RECLAIM, so no
bugs were harmed in the making of this patch.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are several shortcomings with the accounting of shared memory
(SysV shm, shared anonymous mapping, mapping of a tmpfs file). The
values in /proc/<pid>/status and <...>/statm don't allow to distinguish
between shmem memory and a shared mapping to a regular file, even though
theirs implication on memory usage are quite different: during reclaim,
file mapping can be dropped or written back on disk, while shmem needs a
place in swap.
Also, to distinguish the memory occupied by anonymous and file mappings,
one has to read the /proc/pid/statm file, which has a field for the file
mappings (again, including shmem) and total memory occupied by these
mappings (i.e. equivalent to VmRSS in the <...>/status file. Getting
the value for anonymous mappings only is thus not exactly user-friendly
(the statm file is intended to be rather efficiently machine-readable).
To address both of these shortcomings, this patch adds a breakdown of
VmRSS in /proc/<pid>/status via new fields RssAnon, RssFile and
RssShmem, making use of the previous preparatory patch. These fields
tell the user the memory occupied by private anonymous pages, mapped
regular files and shmem, respectively. Other existing fields in /status
and /statm files are left without change. The /statm file can be
extended in the future, if there's a need for that.
Example (part of) /proc/pid/status output including the new Rss* fields:
VmPeak: 2001008 kB
VmSize: 2001004 kB
VmLck: 0 kB
VmPin: 0 kB
VmHWM: 5108 kB
VmRSS: 5108 kB
RssAnon: 92 kB
RssFile: 1324 kB
RssShmem: 3692 kB
VmData: 192 kB
VmStk: 136 kB
VmExe: 4 kB
VmLib: 1784 kB
VmPTE: 3928 kB
VmPMD: 20 kB
VmSwap: 0 kB
HugetlbPages: 0 kB
[vbabka@suse.cz: forward-porting, tweak changelog]
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently looking at /proc/<pid>/status or statm, there is no way to
distinguish shmem pages from pages mapped to a regular file (shmem pages
are mapped to /dev/zero), even though their implication in actual memory
use is quite different.
The internal accounting currently counts shmem pages together with
regular files. As a preparation to extend the userspace interfaces,
this patch adds MM_SHMEMPAGES counter to mm_rss_stat to account for
shmem pages separately from MM_FILEPAGES. The next patch will expose it
to userspace - this patch doesn't change the exported values yet, by
adding up MM_SHMEMPAGES to MM_FILEPAGES at places where MM_FILEPAGES was
used before. The only user-visible change after this patch is the OOM
killer message that separates the reported "shmem-rss" from "file-rss".
[vbabka@suse.cz: forward-porting, tweak changelog]
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Following the previous patch, further reduction of /proc/pid/smaps cost
is possible for private writable shmem mappings with unpopulated areas
where the page walk invokes the .pte_hole function. We can use radix
tree iterator for each such area instead of calling find_get_entry() in
a loop. This is possible at the extra maintenance cost of introducing
another shmem function shmem_partial_swap_usage().
To demonstrate the diference, I have measured this on a process that
creates a private writable 2GB mapping of a partially swapped out
/dev/shm/file (which cannot employ the optimizations from the prvious
patch) and doesn't populate it at all. I time how long does it take to
cat /proc/pid/smaps of this process 100 times.
Before this patch:
real 0m3.831s
user 0m0.180s
sys 0m3.212s
After this patch:
real 0m1.176s
user 0m0.180s
sys 0m0.684s
The time is similar to the case where a radix tree iterator is employed
on the whole mapping.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous patch has improved swap accounting for shmem mapping, which
however made /proc/pid/smaps more expensive for shmem mappings, as we
consult the radix tree for each pte_none entry, so the overal complexity
is O(n*log(n)).
We can reduce this significantly for mappings that cannot contain COWed
pages, because then we can either use the statistics tha shmem object
itself tracks (if the mapping contains the whole object, or the swap
usage of the whole object is zero), or use the radix tree iterator,
which is much more effective than repeated find_get_entry() calls.
This patch therefore introduces a function shmem_swap_usage(vma) and
makes /proc/pid/smaps use it when possible. Only for writable private
mappings of shmem objects (i.e. tmpfs files) with the shmem object
itself (partially) swapped outwe have to resort to the find_get_entry()
approach.
Hopefully such mappings are relatively uncommon.
To demonstrate the diference, I have measured this on a process that
creates a 2GB mapping and dirties single pages with a stride of 2MB, and
time how long does it take to cat /proc/pid/smaps of this process 100
times.
Private writable mapping of a /dev/shm/file (the most complex case):
real 0m3.831s
user 0m0.180s
sys 0m3.212s
Shared mapping of an almost full mapping of a partially swapped /dev/shm/file
(which needs to employ the radix tree iterator).
real 0m1.351s
user 0m0.096s
sys 0m0.768s
Same, but with /dev/shm/file not swapped (so no radix tree walk needed)
real 0m0.935s
user 0m0.128s
sys 0m0.344s
Private anonymous mapping:
real 0m0.949s
user 0m0.116s
sys 0m0.348s
The cost is now much closer to the private anonymous mapping case, unless
the shmem mapping is private and writable.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, /proc/pid/smaps will always show "Swap: 0 kB" for
shmem-backed mappings, even if the mapped portion does contain pages
that were swapped out. This is because unlike private anonymous
mappings, shmem does not change pte to swap entry, but pte_none when
swapping the page out. In the smaps page walk, such page thus looks
like it was never faulted in.
This patch changes smaps_pte_entry() to determine the swap status for
such pte_none entries for shmem mappings, similarly to how
mincore_page() does it. Swapped out shmem pages are thus accounted for.
For private mappings of tmpfs files that COWed some of the pages, swaped
out status of the original shmem pages is naturally ignored. If some of
the private copies was also swapped out, they are accounted via their
page table swap entries, so the resulting reported swap usage is then a
sum of both swapped out private copies, and swapped out shmem pages that
were not COWed. No double accounting can thus happen.
The accounting is arguably still not as precise as for private anonymous
mappings, since now we will count also pages that the process in
question never accessed, but another process populated them and then let
them become swapped out. I believe it is still less confusing and
subtle than not showing any swap usage by shmem mappings at all.
Swapped out counter might of interest of users who would like to prevent
from future swapins during performance critical operation and pre-fault
them at their convenience. Especially for larger swapped out regions
the cost of swapin is much higher than a fresh page allocation. So a
differentiation between pte_none vs. swapped out is important for those
usecases.
One downside of this patch is that it makes /proc/pid/smaps more
expensive for shmem mappings, as we consult the radix tree for each
pte_none entry, so the overal complexity is O(n*log(n)). I have
measured this on a process that creates a 2GB mapping and dirties single
pages with a stride of 2MB, and time how long does it take to cat
/proc/pid/smaps of this process 100 times.
Private anonymous mapping:
real 0m0.949s
user 0m0.116s
sys 0m0.348s
Mapping of a /dev/shm/file:
real 0m3.831s
user 0m0.180s
sys 0m3.212s
The difference is rather substantial, so the next patch will reduce the
cost for shared or read-only mappings.
In a less controlled experiment, I've gathered pids of processes on my
desktop that have either '/dev/shm/*' or 'SYSV*' in smaps. This
included the Chrome browser and some KDE processes. Again, I've run cat
/proc/pid/smaps on each 100 times.
Before this patch:
real 0m9.050s
user 0m0.518s
sys 0m8.066s
After this patch:
real 0m9.221s
user 0m0.541s
sys 0m8.187s
This suggests low impact on average systems.
Note that this patch doesn't attempt to adjust the SwapPss field for
shmem mappings, which would need extra work to determine who else could
have the pages mapped. Thus the value stays zero except for COWed
swapped out pages in a shmem mapping, which are accounted as usual.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When running the SPECint_rate gcc on some very large boxes it was
noticed that the system was spending lots of time in
mpol_shared_policy_lookup(). The gamess benchmark can also show it and
is what I mostly used to chase down the issue since the setup for that I
found to be easier.
To be clear the binaries were on tmpfs because of disk I/O requirements.
We then used text replication to avoid icache misses and having all the
copies banging on the memory where the instruction code resides. This
results in us hitting a bottleneck in mpol_shared_policy_lookup() since
lookup is serialised by the shared_policy lock.
I have only reproduced this on very large (3k+ cores) boxes. The
problem starts showing up at just a few hundred ranks getting worse
until it threatens to livelock once it gets large enough. For example
on the gamess benchmark at 128 ranks this area consumes only ~1% of
time, at 512 ranks it consumes nearly 13%, and at 2k ranks it is over
90%.
To alleviate the contention in this area I converted the spinlock to an
rwlock. This allows a large number of lookups to happen simultaneously.
The results were quite good reducing this consumtion at max ranks to
around 2%.
[akpm@linux-foundation.org: tidy up code comments]
Signed-off-by: Nathan Zimmer <nzimmer@sgi.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Nadia Yvette Chambers <nyc@holomorphy.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark those kmem allocations that are known to be easily triggered from
userspace as __GFP_ACCOUNT/SLAB_ACCOUNT, which makes them accounted to
memcg. For the list, see below:
- threadinfo
- task_struct
- task_delay_info
- pid
- cred
- mm_struct
- vm_area_struct and vm_region (nommu)
- anon_vma and anon_vma_chain
- signal_struct
- sighand_struct
- fs_struct
- files_struct
- fdtable and fdtable->full_fds_bits
- dentry and external_name
- inode for all filesystems. This is the most tedious part, because
most filesystems overwrite the alloc_inode method.
The list is far from complete, so feel free to add more objects.
Nevertheless, it should be close to "account everything" approach and
keep most workloads within bounds. Malevolent users will be able to
breach the limit, but this was possible even with the former "account
everything" approach (simply because it did not account everything in
fact).
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Greg Thelen <gthelen@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, all kmem allocations (namely every kmem_cache_alloc, kmalloc,
alloc_kmem_pages call) are accounted to memory cgroup automatically.
Callers have to explicitly opt out if they don't want/need accounting
for some reason. Such a design decision leads to several problems:
- kmalloc users are highly sensitive to failures, many of them
implicitly rely on the fact that kmalloc never fails, while memcg
makes failures quite plausible.
- A lot of objects are shared among different containers by design.
Accounting such objects to one of containers is just unfair.
Moreover, it might lead to pinning a dead memcg along with its kmem
caches, which aren't tiny, which might result in noticeable increase
in memory consumption for no apparent reason in the long run.
- There are tons of short-lived objects. Accounting them to memcg will
only result in slight noise and won't change the overall picture, but
we still have to pay accounting overhead.
For more info, see
- http://lkml.kernel.org/r/20151105144002.GB15111%40dhcp22.suse.cz
- http://lkml.kernel.org/r/20151106090555.GK29259@esperanza
Therefore this patchset switches to the white list policy. Now kmalloc
users have to explicitly opt in by passing __GFP_ACCOUNT flag.
Currently, the list of accounted objects is quite limited and only
includes those allocations that (1) are known to be easily triggered
from userspace and (2) can fail gracefully (for the full list see patch
no. 6) and it still misses many object types. However, accounting only
those objects should be a satisfactory approximation of the behavior we
used to have for most sane workloads.
This patch (of 6):
Revert 499611ed45 ("kernfs: do not account ino_ida allocations
to memcg").
Black-list kmem accounting policy (aka __GFP_NOACCOUNT) turned out to be
fragile and difficult to maintain, because there seem to be many more
allocations that should not be accounted than those that should be.
Besides, false accounting an allocation might result in much worse
consequences than not accounting at all, namely increased memory
consumption due to pinned dead kmem caches.
So it was decided to switch to the white-list policy. This patch reverts
bits introducing the black-list policy. The white-list policy will be
introduced later in the series.
Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Greg Thelen <gthelen@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lksb flags are defined both in dlmapi.h and dlmcommon.h. So clean them
up from dlmcommon.h.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: Jiufei Xue <xuejiufei@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found this when do patch review, remove to make it clear and save a
little cpu time.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In ocfs2_orphan_del, currently it finds and deletes entry first, and
then access orphan dir dinode. This will have a problem once
ocfs2_journal_access_di fails. In this case, entry will be removed from
orphan dir, but in deed the inode hasn't been deleted successfully. In
other words, the file is missing but not actually deleted. So we should
access orphan dinode first like unlink and rename.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: Jiufei Xue <xuejiufei@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When two processes are migrating the same lockres,
dlm_add_migration_mle() return -EEXIST, but insert a new mle in hash
list. dlm_migrate_lockres() will detach the old mle and free the new
one which is already in hash list, that will destroy the list.
Signed-off-by: Jiufei Xue <xuejiufei@huawei.com>
Reviewed-by: Joseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have found that migration source will trigger a BUG that the refcount
of mle is already zero before put when the target is down during
migration. The situation is as follows:
dlm_migrate_lockres
dlm_add_migration_mle
dlm_mark_lockres_migrating
dlm_get_mle_inuse
<<<<<< Now the refcount of the mle is 2.
dlm_send_one_lockres and wait for the target to become the
new master.
<<<<<< o2hb detect the target down and clean the migration
mle. Now the refcount is 1.
dlm_migrate_lockres woken, and put the mle twice when found the target
goes down which trigger the BUG with the following message:
"ERROR: bad mle: ".
Signed-off-by: Jiufei Xue <xuejiufei@huawei.com>
Reviewed-by: Joseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
DLM does not cache locks. So, blocking lock and unlock will only make
the performance worse where contention over the locks is high.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following case will lead to slot overwritten.
N1 N2
mount ocfs2 volume, find and
allocate slot 0, then set
osb->slot_num to 0, begin to
write slot info to disk
mount ocfs2 volume, wait for super lock
write block fail because of
storage link down, unlock
super lock
got super lock and also allocate slot 0
then unlock super lock
mount fail and then dismount,
since osb->slot_num is 0, try to
put invalid slot to disk. And it
will succeed if storage link
restores.
N2 slot info is now overwritten
Once another node say N3 mount, it will find and allocate slot 0 again,
which will lead to mount hung because journal has already been locked by
N2. so when write slot info failed, invalidate slot in advance to avoid
overwrite slot.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Yiwen Jiang <jiangyiwen@huawei.com>
Reviewed-by: Joseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dlm_grab() may return NULL when the node is doing unmount. When doing
code review, we found that some dlm handlers may return error to caller
when dlm_grab() returns NULL and make caller BUG or other problems.
Here is an example:
Node 1 Node 2
receives migration message
from node 3, and send
migrate request to others
start unmounting
receives migrate request
from node 1 and call
dlm_migrate_request_handler()
unmount thread unregisters
domain handlers and removes
dlm_context from dlm_domains
dlm_migrate_request_handlers()
returns -EINVAL to node 1
Exit migration neither clearing the
migration state nor sending
assert master message to node 3 which
cause node 3 hung.
Signed-off-by: Jiufei Xue <xuejiufei@huawei.com>
Reviewed-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since iput will take care the NULL check itself, NULL check before
calling it is redundant. So clean them up.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit f3f854648d ("ocfs2_dlm: Ensure correct ordering of set/clear
refmap bit on lockres") still exists a race which can't ensure the
ordering is exactly correct.
Node1 Node2 Node3
umount, migrate
lockres to Node2
migrate finished,
send migrate request
to Node3
received migrate request,
create a migration_mle,
respond to Node2.
set DLM_LOCK_RES_SETREF_INPROG
and send assert master to
Node3
delete migration_mle in
assert_master_handler,
Node3 umount without response
dlm_thread purge
this lockres, send drop
deref message to Node2
found the flag of
DLM_LOCK_RES_SETREF_INPROG
is set, dispatch
dlm_deref_lockres_worker to
clear refmap, but in function of
dlm_deref_lockres_worker,
only if node in refmap it wait
DLM_LOCK_RES_SETREF_INPROG
to be cleared. So worker is
done successfully
purge lockres, send
assert master response
to Node1, and finish umount
set Node3 in refmap, and it
won't be cleared forever, thus
lead to umount hung
so wait until DLM_LOCK_RES_SETREF_INPROG is cleared in
dlm_deref_lockres_worker.
Signed-off-by: Yiwen Jiang <jiangyiwen@huawei.com>
Reviewed-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ocfs2_extent_tree_operations structures are never modified, so
declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We found a race between purge and migration when doing code review.
Node A put lockres to purgelist before receiving the migrate message
from node B which is the master. Node A call dlm_mig_lockres_handler to
handle this message.
dlm_mig_lockres_handler
dlm_lookup_lockres
>>>>>> race window, dlm_run_purge_list may run and send
deref message to master, waiting the response
spin_lock(&res->spinlock);
res->state |= DLM_LOCK_RES_MIGRATING;
spin_unlock(&res->spinlock);
dlm_mig_lockres_handler returns
>>>>>> dlm_thread receives the response from master for the deref
message and triggers the BUG because the lockres has the state
DLM_LOCK_RES_MIGRATING with the following message:
dlm_purge_lockres:209 ERROR: 6633EB681FA7474A9C280A4E1A836F0F: res
M0000000000000000030c0300000000 in use after deref
Signed-off-by: Jiufei Xue <xuejiufei@huawei.com>
Reviewed-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When run multiple xattr test of ocfs2-test on a three-nodes cluster,
mount failed sometimes with the following message.
o2hb: Unable to stabilize heartbeart on region D18B775E758D4D80837E8CF3D086AD4A (xvdb)
Stabilize heartbeat depends on the timing order to mount ocfs2 from
cluster nodes and how fast the tcp connections are established. So
increase unsteady interations to leave more time for it.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some versions of tar assume that files with st_blocks == 0 do not
contain any data and will skip reading them entirely. See also commit
9206c56155 ("ext4: return non-zero st_blocks for inline data").
Signed-off-by: John Haxby <john.haxby@oracle.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Acked-by: Gang He <ghe@suse.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In ocfs2_parse_options,
a) it's better to declare variables(small size) outside of while loop;
b) 'option' will be set by match_int, 'option = 0;' makes no sense, if
match_int failed, it just goto bail and return.
Signed-off-by: Norton.Zhu <norton.zhu@huawei.com>
Reviewed-by: Joseph Qi <joseph.qi@huawei.com>
Cc: Gang He <ghe@suse.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Acked-by: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix build errors that happen when CONFIG_LOGFS=y and CONFIG_MTD=m:
fs/built-in.o: In function `logfs_mount':
super.c:(.text+0x92a6f): undefined reference to `logfs_get_sb_mtd'
fs/built-in.o: In function `logfs_get_sb_bdev':
(.text+0x93530): undefined reference to `logfs_get_sb_mtd'
This patch avoids the error by changing the dependencies of logfs in a
way that we can no longer configure logfs as built-in when the MTD core
is a loadable module, while leaving the dependency to require at least
one of MTD or BLOCK to be enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Joern Engel <joern@logfs.org>
Cc: Prasad Joshi <prasadjoshi.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At the time that this code was originally written, call_srcu didn't
exist, so this thread was required to ensure that we waited for that
SRCU grace period to settle before finally freeing the object.
It does exist now however and we can much more efficiently use call_srcu
to handle this. That also allows us to potentially use srcu_barrier to
ensure that they are all of the callbacks have run before proceeding.
In order to conserve space, we union the rcu_head with the g_list.
This will be necessary for nfsd which will allocate marks from a
dedicated slabcache. We have to be able to ensure that all of the
objects are destroyed before destroying the cache. That's fairly
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Cc: Eric Paris <eparis@parisplace.org>
Reviewed-by: Jan Kara <jack@suse.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To make the intention clearer, use list_next_entry instead of
list_entry.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
inode_nohighmem() is sufficient to make sure that page_get_link()
won't try to allocate a highmem page. Moreover, it is sufficient
to make sure that page_symlink/__page_symlink won't do the same
thing. However, any filesystem that manually preseeds the symlink's
page cache upon symlink(2) needs to make sure that the page it
inserts there won't be a highmem one.
Fortunately, only nfs and shmem have run afoul of that...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add some new tracepoints in the nfsd read/write codepaths. The idea
is that this will give us the ability to measure how long each phase of
a read or write operation takes.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
In some cases tmp_bug can be not filled in cifs_filldir and stay uninitialized,
therefore its printk with "%s" modifier can leak content of kernelspace memory.
If old content of this buffer does not contain '\0' access bejond end of
allocated object can crash the host.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Steve French <sfrench@localhost.localdomain>
CC: Stable <stable@vger.kernel.org>
cifs_call_async() queues the MID to the pending list and calls
smb_send_rqst(). If smb_send_rqst() performs a partial send, it sets
the tcpStatus to CifsNeedReconnect and returns an error code to
cifs_call_async(). In this case, cifs_call_async() removes the MID
from the list and returns to the caller.
However, cifs_call_async() releases the server mutex _before_ removing
the MID. This means that a cifs_reconnect() can race with this function
and manage to remove the MID from the list and delete the entry before
cifs_call_async() calls cifs_delete_mid(). This leads to various
crashes due to the use after free in cifs_delete_mid().
Task1 Task2
cifs_call_async():
- rc = -EAGAIN
- mutex_unlock(srv_mutex)
cifs_reconnect():
- mutex_lock(srv_mutex)
- mutex_unlock(srv_mutex)
- list_delete(mid)
- mid->callback()
cifs_writev_callback():
- mutex_lock(srv_mutex)
- delete(mid)
- mutex_unlock(srv_mutex)
- cifs_delete_mid(mid) <---- use after free
Fix this by removing the MID in cifs_call_async() before releasing the
srv_mutex. Also hold the srv_mutex in cifs_reconnect() until the MIDs
are moved out of the pending list.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Acked-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <sfrench@localhost.localdomain>
Currently O_DIRECT is supported with cache=none and cache=strict, but
not cache=loose. Add support for using O_DIRECT when mounted with
cache=loose.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Currently the echo interval is set to 60 seconds using a macro. This
setting determines the interval at which echo requests are sent to the
server on an idling connection. This setting also affects the time
required for a connection to an unresponsive server to timeout.
Making this setting a tunable allows users to control the echo interval
times as well as control the time after which the connecting to an
unresponsive server times out.
To set echo interval, pass the echo_interval=n mount option.
Version four of the patch.
v2: Change MIN and MAX timeout values
v3: Remove incorrect comment in cifs_get_tcp_session
v4: Fix bug in setting echo_intervalw
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Acked-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Commit 7196ac113a ("Fix to check Unique id and FileType when client
refer file directly.") checks whether the uniqueid of an inode has
changed when getting the inode info, but only when using the UNIX
extensions. Add a similar check for SMB2+, since this can be done
without an extra network roundtrip.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Before this patch, only the hostname of the server
is printed when it becomes unresponsive.
This might not be helpful, if the IP-Address has
changed since initial mount when the name was
resolved (e.g. because the IPv6-Prefix changed).
This patch adds the cached IP address of the unresponsive server,
to the log message.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Steve French <sfrench@localhost.localdomain>
Under some conditions, CIFS can repeatedly call the cifs_dbg() logging
wrapper. If done rapidly enough, the console framebuffer can softlockup
or "rcu_sched self-detected stall". Apply the built-in log ratelimiters
to prevent such hangs.
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Signed-off-by: Steve French <smfrench@gmail.com>
CC: Stable <stable@vger.kernel.org>
This update contains:
o extensive CRC validation during log recovery
o several log recovery bug fixes
o Various DAX support fixes
o AGFL size calculation fix
o various cleanups in preparation for new functionality
o project quota ENOSPC notification via netlink
o tracing and debug improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=eCYp
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs updates from Dave Chinner:
"There's not a lot in this - the main addition is the CRC validation of
the entire region of the log that the will be recovered, along with
several log recovery fixes. Most of the rest is small bug fixes and
cleanups.
I have three bug fixes still pending, all that address recently fixed
regressions that I will send to next week after they've had some time
in for-next.
Summary:
- extensive CRC validation during log recovery
- several log recovery bug fixes
- Various DAX support fixes
- AGFL size calculation fix
- various cleanups in preparation for new functionality
- project quota ENOSPC notification via netlink
- tracing and debug improvements"
* tag 'xfs-for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (26 commits)
xfs: handle dquot buffer readahead in log recovery correctly
xfs: inode recovery readahead can race with inode buffer creation
xfs: eliminate committed arg from xfs_bmap_finish
xfs: bmapbt checking on debug kernels too expensive
xfs: add tracepoints to readpage calls
xfs: debug mode log record crc error injection
xfs: detect and trim torn writes during log recovery
xfs: fix recursive splice read locking with DAX
xfs: Don't use reserved blocks for data blocks with DAX
XFS: Use a signed return type for suffix_kstrtoint()
libxfs: refactor short btree block verification
libxfs: pack the agfl header structure so XFS_AGFL_SIZE is correct
libxfs: use a convenience variable instead of open-coding the fork
xfs: fix log ticket type printing
libxfs: make xfs_alloc_fix_freelist non-static
xfs: make xfs_buf_ioend_async() static
xfs: send warning of project quota to userspace via netlink
xfs: get mp from bma->ip in xfs_bmap code
xfs: print name of verifier if it fails
libxfs: Optimize the loop for xfs_bitmap_empty
...
Pull f2fs updates from Jaegeuk Kim:
"This series adds two ioctls to control cached data and fragmented
files. Most of the rest fixes missing error cases and bugs that we
have not covered so far. Summary:
Enhancements:
- support an ioctl to execute online file defragmentation
- support an ioctl to flush cached data
- speed up shrinking of extent_cache entries
- handle broken superblock
- refector dirty inode management infra
- revisit f2fs_map_blocks to handle more cases
- reduce global lock coverage
- add detecting user's idle time
Major bug fixes:
- fix data race condition on cached nat entries
- fix error cases of volatile and atomic writes"
* tag 'for-f2fs-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (87 commits)
f2fs: should unset atomic flag after successful commit
f2fs: fix wrong memory condition check
f2fs: monitor the number of background checkpoint
f2fs: detect idle time depending on user behavior
f2fs: introduce time and interval facility
f2fs: skip releasing nodes in chindless extent tree
f2fs: use atomic type for node count in extent tree
f2fs: recognize encrypted data in f2fs_fiemap
f2fs: clean up f2fs_balance_fs
f2fs: remove redundant calls
f2fs: avoid unnecessary f2fs_balance_fs calls
f2fs: check the page status filled from disk
f2fs: introduce __get_node_page to reuse common code
f2fs: check node id earily when readaheading node page
f2fs: read isize while holding i_mutex in fiemap
Revert "f2fs: check the node block address of newly allocated nid"
f2fs: cover more area with nat_tree_lock
f2fs: introduce max_file_blocks in sbi
f2fs crypto: check CONFIG_F2FS_FS_XATTR for encrypted symlink
f2fs: introduce zombie list for fast shrinking extent trees
...
1/ Media error handling: The 'badblocks' implementation that originated
in md-raid is up-levelled to a generic capability of a block device.
This initial implementation is limited to being consulted in the pmem
block-i/o path. Later, 'badblocks' will be consulted when creating
dax mappings.
2/ Raw block device dax: For virtualization and other cases that want
large contiguous mappings of persistent memory, add the capability to
dax-mmap a block device directly.
3/ Increased /dev/mem restrictions: Add an option to treat all io-memory
as IORESOURCE_EXCLUSIVE, i.e. disable /dev/mem access while a driver is
actively using an address range. This behavior is controlled via the
new CONFIG_IO_STRICT_DEVMEM option and can be overridden by the
existing "iomem=relaxed" kernel command line option.
4/ Miscellaneous fixes include a 'pfn'-device huge page alignment fix,
block device shutdown crash fix, and other small libnvdimm fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7V5r
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"The bulk of this has appeared in -next and independently received a
build success notification from the kbuild robot. The 'for-4.5/block-
dax' topic branch was rebased over the weekend to drop the "block
device end-of-life" rework that Al would like to see re-implemented
with a notifier, and to address bug reports against the badblocks
integration.
There is pending feedback against "libnvdimm: Add a poison list and
export badblocks" received last week. Linda identified some localized
fixups that we will handle incrementally.
Summary:
- Media error handling: The 'badblocks' implementation that
originated in md-raid is up-levelled to a generic capability of a
block device. This initial implementation is limited to being
consulted in the pmem block-i/o path. Later, 'badblocks' will be
consulted when creating dax mappings.
- Raw block device dax: For virtualization and other cases that want
large contiguous mappings of persistent memory, add the capability
to dax-mmap a block device directly.
- Increased /dev/mem restrictions: Add an option to treat all
io-memory as IORESOURCE_EXCLUSIVE, i.e. disable /dev/mem access
while a driver is actively using an address range. This behavior
is controlled via the new CONFIG_IO_STRICT_DEVMEM option and can be
overridden by the existing "iomem=relaxed" kernel command line
option.
- Miscellaneous fixes include a 'pfn'-device huge page alignment fix,
block device shutdown crash fix, and other small libnvdimm fixes"
* tag 'libnvdimm-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (32 commits)
block: kill disk_{check|set|clear|alloc}_badblocks
libnvdimm, pmem: nvdimm_read_bytes() badblocks support
pmem, dax: disable dax in the presence of bad blocks
pmem: fail io-requests to known bad blocks
libnvdimm: convert to statically allocated badblocks
libnvdimm: don't fail init for full badblocks list
block, badblocks: introduce devm_init_badblocks
block: clarify badblocks lifetime
badblocks: rename badblocks_free to badblocks_exit
libnvdimm, pmem: move definition of nvdimm_namespace_add_poison to nd.h
libnvdimm: Add a poison list and export badblocks
nfit_test: Enable DSMs for all test NFITs
md: convert to use the generic badblocks code
block: Add badblock management for gendisks
badblocks: Add core badblock management code
block: fix del_gendisk() vs blkdev_ioctl crash
block: enable dax for raw block devices
block: introduce bdev_file_inode()
restrict /dev/mem to idle io memory ranges
arch: consolidate CONFIG_STRICT_DEVM in lib/Kconfig.debug
...
Generic MTD
* populate the MTD device 'of_node' field (and get a proper 'of_node' symlink
in sysfs)
- This yielded some new helper functions, and changes across a variety of
drivers
* partitioning cleanups, to prepare for better device-tree based partitioning
in the future
- Eliminate a lot of boilerplate for drivers that want to use OF-based
partition parsing
- The DT bindings for this didn't settle yet, so most non-cleanup portions
are deferred for a future release
NAND
* embed a struct mtd_info inside struct nand_chip
- This is really long overdue; too many drivers have to do the same silly
boilerplate to allocate and link up two "independent" structs, when in
fact, everyone is assuming there is an exact 1:1 relationship between a
NAND chips struct and its underlying MTD. This aids improved helpers and
should make certain abstractions easier in the future.
- Also causes a lot of churn, helped along by some automated code
transformations
* add more core support for detecting (and "correcting") bitflips in erased
pages; requires opt-in by drivers, but at least we kill a few bad
implementations and hopefully stave off future ones
* pxa3xx_nand: cleanups, a few fixes, and PM improvements
* new JZ4780 NAND driver
SPI NOR
* provide default erase function, for controllers that just want to send the
SECTOR_ERASE command directly
* fix some module auto-loading issues with device tree ("jedec,spi-nor")
* error handling fixes
* new Mediatek QSPI flash driver
Other
* cfi: force valid geometry Kconfig (finally!)
- this one used to trip up randconfigs occasionally, since bots aren't
deterred by big scary "advanced configuration" menus
More? Probably. See the commit logs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wFQI
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160112' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"Generic MTD:
- populate the MTD device 'of_node' field (and get a proper 'of_node'
symlink in sysfs)
This yielded some new helper functions, and changes across a
variety of drivers
- partitioning cleanups, to prepare for better device-tree based
partitioning in the future
Eliminate a lot of boilerplate for drivers that want to use
OF-based partition parsing
The DT bindings for this didn't settle yet, so most non-cleanup
portions are deferred for a future release
NAND:
- embed a struct mtd_info inside struct nand_chip
This is really long overdue; too many drivers have to do the same
silly boilerplate to allocate and link up two "independent"
structs, when in fact, everyone is assuming there is an exact 1:1
relationship between a NAND chips struct and its underlying MTD.
This aids improved helpers and should make certain abstractions
easier in the future.
Also causes a lot of churn, helped along by some automated code
transformations
- add more core support for detecting (and "correcting") bitflips in
erased pages; requires opt-in by drivers, but at least we kill a
few bad implementations and hopefully stave off future ones
- pxa3xx_nand: cleanups, a few fixes, and PM improvements
- new JZ4780 NAND driver
SPI NOR:
- provide default erase function, for controllers that just want to
send the SECTOR_ERASE command directly
- fix some module auto-loading issues with device tree
("jedec,spi-nor")
- error handling fixes
- new Mediatek QSPI flash driver
Other:
- cfi: force valid geometry Kconfig (finally!)
This one used to trip up randconfigs occasionally, since bots
aren't deterred by big scary "advanced configuration" menus
More? Probably. See the commit logs"
* tag 'for-linus-20160112' of git://git.infradead.org/linux-mtd: (168 commits)
mtd: jz4780_nand: replace if/else blocks with switch/case
mtd: nand: jz4780: Update ecc correction error codes
mtd: nandsim: use nand_get_controller_data()
mtd: jz4780_nand: remove useless mtd->priv = chip assignment
staging: mt29f_spinand: make use of nand_set/get_controller_data() helpers
mtd: nand: make use of nand_set/get_controller_data() helpers
ARM: make use of nand_set/get_controller_data() helpers
mtd: nand: add helpers to access ->priv
mtd: nand: jz4780: driver for NAND devices on JZ4780 SoCs
mtd: nand: jz4740: remove custom 'erased check' implementation
mtd: nand: diskonchip: remove custom 'erased check' implementation
mtd: nand: davinci: remove custom 'erased check' implementation
mtd: nand: use nand_check_erased_ecc_chunk in default ECC read functions
mtd: nand: return consistent error codes in ecc.correct() implementations
doc: dt: mtd: new binding for jz4780-{nand,bch}
mtd: cfi_cmdset_0001: fixing memory leak and handling failed kmalloc
mtd: spi-nor: wait until lock/unlock operations are ready
mtd: tests: consolidate kmalloc/memset 0 call to kzalloc
jffs2: use to_delayed_work
mtd: nand: assign reasonable default name for NAND drivers
...
- bd_acquire() and bd_forget() open-code bdgrab() and bdput()
- raw driver uses igrab() but never checks its return value and always
holds another ref from bind_set() while calling it, so it's
equivalent to bdgrab()
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull networking updates from Davic Miller:
1) Support busy polling generically, for all NAPI drivers. From Eric
Dumazet.
2) Add byte/packet counter support to nft_ct, from Floriani Westphal.
3) Add RSS/XPS support to mvneta driver, from Gregory Clement.
4) Implement IPV6_HDRINCL socket option for raw sockets, from Hannes
Frederic Sowa.
5) Add support for T6 adapter to cxgb4 driver, from Hariprasad Shenai.
6) Add support for VLAN device bridging to mlxsw switch driver, from
Ido Schimmel.
7) Add driver for Netronome NFP4000/NFP6000, from Jakub Kicinski.
8) Provide hwmon interface to mlxsw switch driver, from Jiri Pirko.
9) Reorganize wireless drivers into per-vendor directories just like we
do for ethernet drivers. From Kalle Valo.
10) Provide a way for administrators "destroy" connected sockets via the
SOCK_DESTROY socket netlink diag operation. From Lorenzo Colitti.
11) Add support to add/remove multicast routes via netlink, from Nikolay
Aleksandrov.
12) Make TCP keepalive settings per-namespace, from Nikolay Borisov.
13) Add forwarding and packet duplication facilities to nf_tables, from
Pablo Neira Ayuso.
14) Dead route support in MPLS, from Roopa Prabhu.
15) TSO support for thunderx chips, from Sunil Goutham.
16) Add driver for IBM's System i/p VNIC protocol, from Thomas Falcon.
17) Rationalize, consolidate, and more completely document the checksum
offloading facilities in the networking stack. From Tom Herbert.
18) Support aborting an ongoing scan in mac80211/cfg80211, from
Vidyullatha Kanchanapally.
19) Use per-bucket spinlock for bpf hash facility, from Tom Leiming.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1375 commits)
net: bnxt: always return values from _bnxt_get_max_rings
net: bpf: reject invalid shifts
phonet: properly unshare skbs in phonet_rcv()
dwc_eth_qos: Fix dma address for multi-fragment skbs
phy: remove an unneeded condition
mdio: remove an unneed condition
mdio_bus: NULL dereference on allocation error
net: Fix typo in netdev_intersect_features
net: freescale: mac-fec: Fix build error from phy_device API change
net: freescale: ucc_geth: Fix build error from phy_device API change
bonding: Prevent IPv6 link local address on enslaved devices
IB/mlx5: Add flow steering support
net/mlx5_core: Export flow steering API
net/mlx5_core: Make ipv4/ipv6 location more clear
net/mlx5_core: Enable flow steering support for the IB driver
net/mlx5_core: Initialize namespaces only when supported by device
net/mlx5_core: Set priority attributes
net/mlx5_core: Connect flow tables
net/mlx5_core: Introduce modify flow table command
net/mlx5_core: Managing root flow table
...
wear leveling improvement by Sebastian Siewior.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Zouw
-----END PGP SIGNATURE-----
Merge tag 'upstream-4.5-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS updates from Richard Weinberger:
"This contains three changes - two cleanups and one UBI wear leveling
improvement by Sebastian Siewior"
* tag 'upstream-4.5-rc1' of git://git.infradead.org/linux-ubifs:
ubifs: Use XATTR_*_PREFIX_LEN
UBIFS: add a comment in key.h for unused parameter
mtd: ubi: wl: avoid erasing a PEB which is empty
- I'm assisting Joel as co-maintainer and patch monkey now, and you will
see pull reuquests from me for a while
- Besides the MAINTAINERS update there is just a single change, which
adds support for binary attributes to configfs, which are very similar
to the sysfs binary attributes. Thanks to Pantelis Antoniou!
- You will see another actually bigger set of configfs changes in the
SCSI target pull from Nic - those were merged before this new tree
even existed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=FjkZ
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-linus' of git://git.infradead.org/users/hch/configfs
Pull configfs updates from Christoph Hellwig:
"I'm assisting Joel as co-maintainer and patch monkey now, and you will
see pull reuquests from me for a while.
Besides the MAINTAINERS update there is just a single change, which
adds support for binary attributes to configfs, which are very similar
to the sysfs binary attributes. Thanks to Pantelis Antoniou!
You will see another actually bigger set of configfs changes in the
SCSI target pull from Nic - those were merged before this new tree
even existed"
* tag 'configfs-for-linus' of git://git.infradead.org/users/hch/configfs:
configfs: add myself as co-maintainer, updated git tree
configfs: implement binary attributes
Here is a list of patches we've accumulated for GFS2 for the current upstream
merge window. Last window's set was short, but I warned that this one would
be bigger, and so it is. We've got 19 patches:
- A patch from Abhi Das to propagate the GFS2_DIF_SYSTEM bit so that newly
added journals don't get flagged, deleted, and recreated by fsck.gfs2.
- Two patches from Andreas Gruenbacher to improve GFS2 performance where
extended attributes are involved.
- A patch from Andy Price to fix a suspicious rcu dereference error.
- Two patches from Ben Marzinski that rework how GFS2's NFS cookies are
managed. This fixes readdir problems with nfs-over-gfs2.
- A patch from Ben Marzinski that fixes a race in unmounting GFS2.
- A set of four patches from me to move the resource group reservations
inside the gfs2 inode to improve performance and fix a bug whereby
get_write_access improperly prevented some operations like chown.
- A patch from me to spinlock-protect the setting of system statfs file data.
This was causing small discrepancies between df and du.
- A patch from me to reintroduce a timeout while clearing glocks which was
accidentally dropped some time ago.
- A patch from me to wait for iopen glock dequeues in order to improve
deleting of files that were unlinked from a different cluster node.
- A patch from me to ensure metadata address spaces get truncated when an
inode is evicted.
- A patch from me to fix a bug in which a memory leak could occur in some
error cases when inodes were trying to be created.
- A patch to consistently use iopen glocks to transition from the unlinked
state to the deleted state.
- A patch to fix a glock reference count error when inode creation fails.
- A patch from Junxiao Bi to fix an flock panic.
- A patch from Markus Elfring that removes an unnecessary if.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWlUOCAAoJENeLYdPf93o78/IH/0PfoQtQnYQpvbTPgaFICEUI
rx+uLqPxpJgjJMsbIy+VA/bhZsbuENDbor99Cs6GiTLy3Q/4TKNY9NxDN+aO8o+Q
qrp3ZANkyTGaneCzrXzfgmOxe1G8xRQ7pboRUEt2yPlGK1oLax+PR4uPb+IuJ5Wa
QvSwnZj+9K2LkMQkKPyxoltjZiZLywvNB5dx0F35+dvriQxHXfJ1Naek6gs140MB
SfG4/Zi8dfGOJQjSQTUENatFhyFB0V7CbDPFuBVzTGD8IS4ASgqIBMFjO0VBHkP4
gt4zb0BJAn0aQcbxIaDtsuEffpn+5zdK/Onq5g4Fr9ZJv3fkVpVcOgYui/rkDD0=
=28ev
-----END PGP SIGNATURE-----
Merge tag 'gfs2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull GFS2 updates from Bob Peterson:
"Here is a list of patches we've accumulated for GFS2 for the current
upstream merge window. Last window's set was short, but I warned that
this one would be bigger, and so it is. We've got 19 patches:
- A patch from Abhi Das to propagate the GFS2_DIF_SYSTEM bit so that
newly added journals don't get flagged, deleted, and recreated by
fsck.gfs2.
- Two patches from Andreas Gruenbacher to improve GFS2 performance
where extended attributes are involved.
- A patch from Andy Price to fix a suspicious rcu dereference error.
- Two patches from Ben Marzinski that rework how GFS2's NFS cookies
are managed. This fixes readdir problems with nfs-over-gfs2.
- A patch from Ben Marzinski that fixes a race in unmounting GFS2.
- A set of four patches from me to move the resource group
reservations inside the gfs2 inode to improve performance and fix a
bug whereby get_write_access improperly prevented some operations
like chown.
- A patch from me to spinlock-protect the setting of system statfs
file data. This was causing small discrepancies between df and du.
- A patch from me to reintroduce a timeout while clearing glocks
which was accidentally dropped some time ago.
- A patch from me to wait for iopen glock dequeues in order to
improve deleting of files that were unlinked from a different
cluster node.
- A patch from me to ensure metadata address spaces get truncated
when an inode is evicted.
- A patch from me to fix a bug in which a memory leak could occur in
some error cases when inodes were trying to be created.
- A patch to consistently use iopen glocks to transition from the
unlinked state to the deleted state.
- A patch to fix a glock reference count error when inode creation
fails.
- A patch from Junxiao Bi to fix an flock panic.
- A patch from Markus Elfring that removes an unnecessary if"
* tag 'gfs2-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: fix flock panic issue
GFS2: Don't do glock put on when inode creation fails
GFS2: Always use iopen glock for gl_deletes
GFS2: Release iopen glock in gfs2_create_inode error cases
GFS2: Truncate address space mapping when deleting an inode
GFS2: Wait for iopen glock dequeues
gfs2: clear journal live bit in gfs2_log_flush
gfs2: change gfs2 readdir cookie
gfs2: keep offset when splitting dir leaf blocks
GFS2: Reintroduce a timeout in function gfs2_gl_hash_clear
GFS2: Update master statfs buffer with sd_statfs_spin locked
GFS2: Reduce size of incore inode
GFS2: Make rgrp reservations part of the gfs2_inode structure
GFS2: Extract quota data from reservations structure (revert 5407e24)
gfs2: Extended attribute readahead optimization
gfs2: Extended attribute readahead
GFS2: Use rht_for_each_entry_rcu in glock_hash_walk
GFS2: Delete an unnecessary check before the function call "iput"
gfs2: Automatically set GFS2_DIF_SYSTEM flag on system files
Pull misc vfs updates from Al Viro:
"All kinds of stuff. That probably should've been 5 or 6 separate
branches, but by the time I'd realized how large and mixed that bag
had become it had been too close to -final to play with rebasing.
Some fs/namei.c cleanups there, memdup_user_nul() introduction and
switching open-coded instances, burying long-dead code, whack-a-mole
of various kinds, several new helpers for ->llseek(), assorted
cleanups and fixes from various people, etc.
One piece probably deserves special mention - Neil's
lookup_one_len_unlocked(). Similar to lookup_one_len(), but gets
called without ->i_mutex and tries to avoid ever taking it. That, of
course, means that it's not useful for any directory modifications,
but things like getting inode attributes in nfds readdirplus are fine
with that. I really should've asked for moratorium on lookup-related
changes this cycle, but since I hadn't done that early enough... I
*am* asking for that for the coming cycle, though - I'm going to try
and get conversion of i_mutex to rwsem with ->lookup() done under lock
taken shared.
There will be a patch closer to the end of the window, along the lines
of the one Linus had posted last May - mechanical conversion of
->i_mutex accesses to inode_lock()/inode_unlock()/inode_trylock()/
inode_is_locked()/inode_lock_nested(). To quote Linus back then:
-----
| This is an automated patch using
|
| sed 's/mutex_lock(&\(.*\)->i_mutex)/inode_lock(\1)/'
| sed 's/mutex_unlock(&\(.*\)->i_mutex)/inode_unlock(\1)/'
| sed 's/mutex_lock_nested(&\(.*\)->i_mutex,[ ]*I_MUTEX_\([A-Z0-9_]*\))/inode_lock_nested(\1, I_MUTEX_\2)/'
| sed 's/mutex_is_locked(&\(.*\)->i_mutex)/inode_is_locked(\1)/'
| sed 's/mutex_trylock(&\(.*\)->i_mutex)/inode_trylock(\1)/'
|
| with a very few manual fixups
-----
I'm going to send that once the ->i_mutex-affecting stuff in -next
gets mostly merged (or when Linus says he's about to stop taking
merges)"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
nfsd: don't hold i_mutex over userspace upcalls
fs:affs:Replace time_t with time64_t
fs/9p: use fscache mutex rather than spinlock
proc: add a reschedule point in proc_readfd_common()
logfs: constify logfs_block_ops structures
fcntl: allow to set O_DIRECT flag on pipe
fs: __generic_file_splice_read retry lookup on AOP_TRUNCATED_PAGE
fs: xattr: Use kvfree()
[s390] page_to_phys() always returns a multiple of PAGE_SIZE
nbd: use ->compat_ioctl()
fs: use block_device name vsprintf helper
lib/vsprintf: add %*pg format specifier
fs: use gendisk->disk_name where possible
poll: plug an unused argument to do_poll
amdkfd: don't open-code memdup_user()
cdrom: don't open-code memdup_user()
rsxx: don't open-code memdup_user()
mtip32xx: don't open-code memdup_user()
[um] mconsole: don't open-code memdup_user_nul()
[um] hostaudio: don't open-code memdup_user()
...
Pull vfs copy_file_range updates from Al Viro:
"Several series around copy_file_range/CLONE"
* 'work.copy_file_range' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
btrfs: use new dedupe data function pointer
vfs: hoist the btrfs deduplication ioctl to the vfs
vfs: wire up compat ioctl for CLONE/CLONE_RANGE
cifs: avoid unused variable and label
nfsd: implement the NFSv4.2 CLONE operation
nfsd: Pass filehandle to nfs4_preprocess_stateid_op()
vfs: pull btrfs clone API to vfs layer
locks: new locks_mandatory_area calling convention
vfs: Add vfs_copy_file_range() support for pagecache copies
btrfs: add .copy_file_range file operation
x86: add sys_copy_file_range to syscall tables
vfs: add copy_file_range syscall and vfs helper
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWkwhdAAoJEAAOaEEZVoIVgpUQAMhB2+ryZtlJy4s7lkfI3Wwi
ni7lAuJ6xXB0FIA8wqNzz6fVDY0pbsfwR45OS11fh+hU2FnM8REHCDPC47E8MQYx
ft0Kfp7Z0tLAPni7XTVd/gFy8zTDGOKXBlu44PNaVEdtPJzIXwVzm2QkT7F3ExOz
mkXSCta7lFemBQ0DhbafiWbfQ8yav1HFGZG7XN06A76y8ZET+Uu1oyiPPI4jvHlO
vHrxpwia2ROnQHeG0pLR7KvOmN3ZSTJZuH6LiMZH0QFqyocYzmhR9rQ/hrxBg0rU
IDzcMjP0ybU9Fu/o7sDShnkTawRuVLt0zasfdlYtGVCTYBx8f7WqkJnLTCwWYVDG
MLQM7y8xWHM1f7uLhgT8WHg8O/e5saVUQ/djBqPI/ubGG1/LHDxyxH/GPVbeKa66
G8jChyPmIdxdsjIapzefOjnTIi2vhZqv9I1gSKCj+x554GahoYQe7l0YbNnZGmNS
O12QQ7dUpkzgDQEiTh73S3Ay2Ng95K2DztuHs6NXFdbiwpFMZqVATLXBEOYryBx/
n487ZqrsTV7T3jH/ekxth1+j0Hpmigj8FNy21/nZ0Nr0OaTJFwsLEdN4Vi7LIM+H
jBMEBk5dGIHODMvB/8NCud0eWzB671iLgVto7or/rT1YmaFapl/KR7FEWNv19sLN
tshSViTosLGffQMpObOk
=wJUS
-----END PGP SIGNATURE-----
Merge tag 'locks-v4.5-1' of git://git.samba.org/jlayton/linux
Pull file locking updates from Jeff Layton:
"File locking related changes for v4.5 (pile #1)
Highlights:
- new Kconfig option to allow disabling mandatory locking (which is
racy anyway)
- new tracepoints for setlk and close codepaths
- fix for a long-standing bug in code that handles races between
setting a POSIX lock and close()"
* tag 'locks-v4.5-1' of git://git.samba.org/jlayton/linux:
locks: rename __posix_lock_file to posix_lock_inode
locks: prink more detail when there are leaked locks
locks: pass inode pointer to locks_free_lock_context
locks: sprinkle some tracepoints around the file locking code
locks: don't check for race with close when setting OFD lock
locks: fix unlock when fcntl_setlk races with a close
fs: make locks.c explicitly non-modular
locks: use list_first_entry_or_null()
locks: Don't allow mounts in user namespaces to enable mandatory locking
locks: Allow disabling mandatory locking at compile time
Pull UML updates from Richard Weinberger:
"This contains beside of random fixes/cleanups two bigger changes:
- seccomp support by Mickaël Salaün
- IRQ rework by Anton Ivanov"
* 'for-linus-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Use race-free temporary file creation
um: Do not set unsecure permission for temporary file
um: Fix build error and kconfig for i386
um: Add seccomp support
um: Add full asm/syscall.h support
selftests/seccomp: Remove the need for HAVE_ARCH_TRACEHOOK
um: Fix ptrace GETREGS/SETREGS bugs
um: link with -lpthread
um: Update UBD to use pread/pwrite family of functions
um: Do not change hard IRQ flags in soft IRQ processing
um: Prevent IRQ handler reentrancy
uml: flush stdout before forking
uml: fix hostfs mknod()
This patch fixes wrong decision for avaliable_free_memory.
The return valus is already set as false, so we should consider true condition
below only.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds last time that user requested filesystem operations.
This information is used to detect whether system is idle or not later.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Pull vfs xattr updates from Al Viro:
"Andreas' xattr cleanup series.
It's a followup to his xattr work that went in last cycle; -0.5KLoC"
* 'work.xattr' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
xattr handlers: Simplify list operation
ocfs2: Replace list xattr handler operations
nfs: Move call to security_inode_listsecurity into nfs_listxattr
xfs: Change how listxattr generates synthetic attributes
tmpfs: listxattr should include POSIX ACL xattrs
tmpfs: Use xattr handler infrastructure
btrfs: Use xattr handler infrastructure
vfs: Distinguish between full xattr names and proper prefixes
posix acls: Remove duplicate xattr name definitions
gfs2: Remove gfs2_xattr_acl_chmod
vfs: Remove vfs_xattr_cmp
Pull vfs RCU symlink updates from Al Viro:
"Replacement of ->follow_link/->put_link, allowing to stay in RCU mode
even if the symlink is not an embedded one.
No changes since the mailbomb on Jan 1"
* 'work.symlinks' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
switch ->get_link() to delayed_call, kill ->put_link()
kill free_page_put_link()
teach nfs_get_link() to work in RCU mode
teach proc_self_get_link()/proc_thread_self_get_link() to work in RCU mode
teach shmem_get_link() to work in RCU mode
teach page_get_link() to work in RCU mode
replace ->follow_link() with new method that could stay in RCU mode
don't put symlink bodies in pagecache into highmem
namei: page_getlink() and page_follow_link_light() are the same thing
ufs: get rid of ->setattr() for symlinks
udf: don't duplicate page_symlink_inode_operations
logfs: don't duplicate page_symlink_inode_operations
switch befs long symlinks to page_symlink_operations
When we do dquot readahead in log recovery, we do not use a verifier
as the underlying buffer may not have dquots in it. e.g. the
allocation operation hasn't yet been replayed. Hence we do not want
to fail recovery because we detect an operation to be replayed has
not been run yet. This problem was addressed for inodes in commit
d891400 ("xfs: inode buffers may not be valid during recovery
readahead") but the problem was not recognised to exist for dquots
and their buffers as the dquot readahead did not have a verifier.
The result of not using a verifier is that when the buffer is then
next read to replay a dquot modification, the dquot buffer verifier
will only be attached to the buffer if *readahead is not complete*.
Hence we can read the buffer, replay the dquot changes and then add
it to the delwri submission list without it having a verifier
attached to it. This then generates warnings in xfs_buf_ioapply(),
which catches and warns about this case.
Fix this and make it handle the same readahead verifier error cases
as for inode buffers by adding a new readahead verifier that has a
write operation as well as a read operation that marks the buffer as
not done if any corruption is detected. Also make sure we don't run
readahead if the dquot buffer has been marked as cancelled by
recovery.
This will result in readahead either succeeding and the buffer
having a valid write verifier, or readahead failing and the buffer
state requiring the subsequent read to resubmit the IO with the new
verifier. In either case, this will result in the buffer always
ending up with a valid write verifier on it.
Note: we also need to fix the inode buffer readahead error handling
to mark the buffer with EIO. Brian noticed the code I copied from
there wrong during review, so fix it at the same time. Add comments
linking the two functions that handle readahead verifier errors
together so we don't forget this behavioural link in future.
cc: <stable@vger.kernel.org> # 3.12 - current
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
When we do inode readahead in log recovery, we do can do the
readahead before we've replayed the icreate transaction that stamps
the buffer with inode cores. The inode readahead verifier catches
this and marks the buffer as !done to indicate that it doesn't yet
contain valid inodes.
In adding buffer error notification (i.e. setting b_error = -EIO at
the same time as as we clear the done flag) to such a readahead
verifier failure, we can then get subsequent inode recovery failing
with this error:
XFS (dm-0): metadata I/O error: block 0xa00060 ("xlog_recover_do..(read#2)") error 5 numblks 32
This occurs when readahead completion races with icreate item replay
such as:
inode readahead
find buffer
lock buffer
submit RA io
....
icreate recovery
xfs_trans_get_buffer
find buffer
lock buffer
<blocks on RA completion>
.....
<ra completion>
fails verifier
clear XBF_DONE
set bp->b_error = -EIO
release and unlock buffer
<icreate gains lock>
icreate initialises buffer
marks buffer as done
adds buffer to delayed write queue
releases buffer
At this point, we have an initialised inode buffer that is up to
date but has an -EIO state registered against it. When we finally
get to recovering an inode in that buffer:
inode item recovery
xfs_trans_read_buffer
find buffer
lock buffer
sees XBF_DONE is set, returns buffer
sees bp->b_error is set
fail log recovery!
Essentially, we need xfs_trans_get_buf_map() to clear the error status of
the buffer when doing a lookup. This function returns uninitialised
buffers, so the buffer returned can not be in an error state and
none of the code that uses this function expects b_error to be set
on return. Indeed, there is an ASSERT(!bp->b_error); in the
transaction case in xfs_trans_get_buf_map() that would have caught
this if log recovery used transactions....
This patch firstly changes the inode readahead failure to set -EIO
on the buffer, and secondly changes xfs_buf_get_map() to never
return a buffer with an error state set so this first change doesn't
cause unexpected log recovery failures.
cc: <stable@vger.kernel.org> # 3.12 - current
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Calls to xfs_bmap_finish() and xfs_trans_ijoin(), and the
associated comments were replicated several times across
the attribute code, all dealing with what to do if the
transaction was or wasn't committed.
And in that replicated code, an ASSERT() test of an
uninitialized variable occurs in several locations:
error = xfs_attr_thing(&args);
if (!error) {
error = xfs_bmap_finish(&args.trans, args.flist,
&committed);
}
if (error) {
ASSERT(committed);
If the first xfs_attr_thing() failed, we'd skip the xfs_bmap_finish,
never set "committed", and then test it in the ASSERT.
Fix this up by moving the committed state internal to xfs_bmap_finish,
and add a new inode argument. If an inode is passed in, it is passed
through to __xfs_trans_roll() and joined to the transaction there if
the transaction was committed.
xfs_qm_dqalloc() was a little unique in that it called bjoin rather
than ijoin, but as Dave points out we can detect the committed state
but checking whether (*tpp != tp).
Addresses-Coverity-Id: 102360
Addresses-Coverity-Id: 102361
Addresses-Coverity-Id: 102363
Addresses-Coverity-Id: 102364
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
An inverted return value check in hostfs_mknod() caused the function
to return success after handling it as an error (and cleaning up).
It resulted in the following segfault when trying to bind() a named
unix socket:
Pid: 198, comm: a.out Not tainted 4.4.0-rc4
RIP: 0033:[<0000000061077df6>]
RSP: 00000000daae5d60 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 000000006092a460 RCX: 00000000dfc54208
RDX: 0000000061073ef1 RSI: 0000000000000070 RDI: 00000000e027d600
RBP: 00000000daae5de0 R08: 00000000da980ac0 R09: 0000000000000000
R10: 0000000000000003 R11: 00007fb1ae08f72a R12: 0000000000000000
R13: 000000006092a460 R14: 00000000daaa97c0 R15: 00000000daaa9a88
Kernel panic - not syncing: Kernel mode fault at addr 0x40, ip 0x61077df6
CPU: 0 PID: 198 Comm: a.out Not tainted 4.4.0-rc4 #1
Stack:
e027d620 dfc54208 0000006f da981398
61bee000 0000c1ed daae5de0 0000006e
e027d620 dfcd4208 00000005 6092a460
Call Trace:
[<60dedc67>] SyS_bind+0xf7/0x110
[<600587be>] handle_syscall+0x7e/0x80
[<60066ad7>] userspace+0x3e7/0x4e0
[<6006321f>] ? save_registers+0x1f/0x40
[<6006c88e>] ? arch_prctl+0x1be/0x1f0
[<60054985>] fork_handler+0x85/0x90
Let's also get rid of the "cosmic ray protection" while we're at it.
Fixes: e9193059b1 "hostfs: fix races in dentry_name() and inode_name()"
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Add a comment in key.h to explain why we keep an unused
parameter in key helpers.
Signed-off-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
If an application wants exclusive access to all of the persistent memory
provided by an NVDIMM namespace it can use this raw-block-dax facility
to forgo establishing a filesystem. This capability is targeted
primarily to hypervisors wanting to provision persistent memory for
guests. It can be disabled / enabled dynamically via the new BLKDAXSET
ioctl.
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reviewed-by: Jan Kara <jack@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Similar to the file_inode() helper, provide a helper to lookup the inode for a
raw block device itself.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Suggested-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We need information about exports when crossing mountpoints during
lookup or NFSv4 readdir. If we don't already have that information
cached, we may have to ask (and wait for) rpc.mountd.
In both cases we currently hold the i_mutex on the parent of the
directory we're asking rpc.mountd about. We've seen situations where
rpc.mountd performs some operation on that directory that tries to take
the i_mutex again, resulting in deadlock.
With some care, we may be able to avoid that in rpc.mountd. But it
seems better just to avoid holding a mutex while waiting on userspace.
It appears that lookup_one_len is pretty much the only operation that
needs the i_mutex. So we could just drop the i_mutex elsewhere and do
something like
mutex_lock()
lookup_one_len()
mutex_unlock()
In many cases though the lookup would have been cached and not required
the i_mutex, so it's more efficient to create a lookup_one_len() variant
that only takes the i_mutex when necessary.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The affs code uses "time_t" and "get_seconds()". This will cause
problems on 32-bit architectures in 2038 when time_t overflows.
This patch replaces them with "time64_t" and
"ktime_get_real_seconds()". This patch introduces expensive 64-bit
divsion in "secs_to_datestamp()", considering this function is not
called so often, the cost should be acceptable.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: DengChao <chao.deng@linaro.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We may sleep inside a the lock, so use a mutex rather than spinlock.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
User can pass an arbitrary large buffer to getdents().
It is typically a 32KB buffer used by libc scandir() implementation.
When scanning /proc/{pid}/fd, we can hold cpu way too long,
so add a cond_resched() to be kind with other tasks.
We've seen latencies of more than 50ms on real workloads.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The logfs_block_ops structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
With packetized mode for pipes, it's not possible to set O_DIRECT on pipe file
via sys_fcntl, because of unsupported sanity checks.
Ability to set this flag will be used by CRIU to migrate packetized pipes.
v2:
Fixed typos and mode variable to check.
Signed-off-by: Stanislav Kinsburskiy <skinsbursky@virtuozzo.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
During testing, I discovered that __generic_file_splice_read() returns
0 (EOF) when aops->readpage fails with AOP_TRUNCATED_PAGE on the first
page of a single/multi-page splice read operation. This EOF return code
causes the userspace test to (correctly) report a zero-length read error
when it was expecting otherwise.
The current strategy of returning a partial non-zero read when ->readpage
returns AOP_TRUNCATED_PAGE works only when the failed page is not the
first of the lot being processed.
This patch attempts to retry lookup and call ->readpage again on pages
that had previously failed with AOP_TRUNCATED_PAGE. With this patch, my
tests pass and I haven't noticed any unwanted side effects.
This version removes the thrice-retry loop and instead indefinitely
retries lookups on AOP_TRUNCATED_PAGE errors from ->readpage. This
behavior is now similar to do_generic_file_read().
Signed-off-by: Abhi Das <adas@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This replaces all code in fs/compat_ioctl.c that translated
ioctl arguments into a in-kernel structure, then performed
do_ioctl under set_fs(KERNEL_DS), with code that allocates
data on the user stack and can call the VFS ioctl handler
under USER_DS.
This is done as a hardening measure because the caller
does not know what kind of ioctl handler will be invoked,
only that no corresponding compat_ioctl handler exists and
what the ioctl command number is. The accidental
invocation of an unlocked_ioctl handler that unexpectedly
calls copy_to_user could be a severe security issue.
Signed-off-by: Jann Horn <jann@thejh.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In code in fs/compat_ioctl.c that translates ioctl arguments
into a in-kernel structure, then performs sys_ioctl, possibly
under set_fs(KERNEL_DS), this commit changes the sys_ioctl
calls to do_ioctl calls. do_ioctl is a new function that does
the same thing as sys_ioctl, but doesn't look up the fd again.
This change is made to avoid (potential) security issues
because of ioctl handlers that accept one of the ioctl
commands I2C_FUNCS, VIDEO_GET_EVENT, MTIOCPOS, MTIOCGET,
TIOCGSERIAL, TIOCSSERIAL, RTC_IRQP_READ, RTC_EPOCH_READ.
This can happen for multiple reasons:
- The ioctl command number could be reused.
- The ioctl handler might not check the full ioctl
command. This is e.g. true for drm_ioctl.
- The ioctl handler is very special, e.g. cuse_file_ioctl
The real issue is that set_fs(KERNEL_DS) is used here,
but that's fixed in a separate commit
"compat_ioctl: don't call do_ioctl under set_fs(KERNEL_DS)".
This change mitigates potential security issues by
preventing a race that permits invocation of
unlocked_ioctl handlers under KERNEL_DS through compat
code even if a corresponding compat_ioctl handler exists.
So far, no way has been identified to use this to damage
kernel memory without having CAP_SYS_ADMIN in the init ns
(with the capability, doing reads/writes at arbitrary
kernel addresses should be easy through CUSE's ioctl
handler with FUSE_IOCTL_UNRESTRICTED set).
[AV: two missed sys_ioctl() taken care of]
Signed-off-by: Jann Horn <jann@thejh.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Have the CB_LAYOUTRECALL code treat NFS4_OK and NFS4ERR_DELAY returns
equivalently. Change the code to periodically resend CB_LAYOUTRECALLS
until the ls_layouts list is empty or the client returns a different
error code.
If we go for two lease periods without the list being emptied or the
client sending a hard error, then we give up and clean out the list
anyway.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Tested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This patch adds FS_IOC_FSSETXATTR/FS_IOC_FSGETXATTR ioctl interface
support for ext4. The interface is kept consistent with
XFS_IOC_FSGETXATTR/XFS_IOC_FSGETXATTR.
Signed-off-by: Li Xi <lixi@ddn.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Reviewed-by: Jan Kara <jack@suse.cz>
This patch adds mount options for enabling/disabling project quota
accounting and enforcement. A new specific inode is also used for
project quota accounting.
[ Includes fix from Dan Carpenter to crrect error checking from dqget(). ]
Signed-off-by: Li Xi <lixi@ddn.com>
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Li Xi <lixi@ddn.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Reviewed-by: Jan Kara <jack@suse.cz>
A number of functions include ext4_add_dx_entry, make_indexed_dir,
etc. are being passed a dentry even though the only thing they use is
the containing parent. We can shrink the code size slightly by making
this replacement. This will also be useful in cases where we don't
have a dentry as the argument to the directory entry insert functions.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
If there are no nodes in extent tree, let's skip releasing step to avoid
any overhead of grabbing/releasing extent tree lock.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
1. rename field in struct extent_tree from count to node_cnt for
readability.
2. alter to use atomic type for node_cnt.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch fixes to teach f2fs_fiemap to recognize encrypted data.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
There are duplicated code in between get_node_page and get_node_page_ra,
introduce __get_node_page to includes common parts of these two, and
export get_node_page and get_node_page_ra by reusing __get_node_page.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Add node id check in ra_node_page and get_node_page_ra like get_node_page.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
...a more descriptive name and we can drop the double underscore prefix.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Acked-by: "J. Bruce Fields" <bfields@fieldses.org>
Right now, we just get WARN_ON_ONCE, which is not particularly helpful.
Have it dump some info about the locks and the inode to make it easier
to track down leaked locks in the future.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Acked-by: "J. Bruce Fields" <bfields@fieldses.org>
...so we can print information about it if there are leaked locks.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Acked-by: "J. Bruce Fields" <bfields@fieldses.org>
Add some tracepoints around the POSIX locking code. These were useful
when tracking down problems when handling the race between setlk and
close.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Acked-by: "J. Bruce Fields" <bfields@fieldses.org>
We don't clean out OFD locks on close(), so there's no need to check
for a race with them here. They'll get cleaned out at the same time
that flock locks are.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Acked-by: "J. Bruce Fields" <bfields@fieldses.org>
Dmitry reported that he was able to reproduce the WARN_ON_ONCE that
fires in locks_free_lock_context when the flc_posix list isn't empty.
The problem turns out to be that we're basically rebuilding the
file_lock from scratch in fcntl_setlk when we discover that the setlk
has raced with a close. If the l_whence field is SEEK_CUR or SEEK_END,
then we may end up with fl_start and fl_end values that differ from
when the lock was initially set, if the file position or length of the
file has changed in the interim.
Fix this by just reusing the same lock request structure, and simply
override fl_type value with F_UNLCK as appropriate. That ensures that
we really are unlocking the lock that was initially set.
While we're there, make sure that we do pop a WARN_ON_ONCE if the
removal ever fails. Also return -EBADF in this event, since that's
what we would have returned if the close had happened earlier.
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Fixes: c293621bbf (stale POSIX lock handling)
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Acked-by: "J. Bruce Fields" <bfields@fieldses.org>
For large sparse or fragmented files, checking every single entry in
the bmapbt on every operation is prohibitively expensive. Especially
as such checks rarely discover problems during normal operations on
high extent coutn files. Our regression tests don't tend to exercise
files with hundreds of thousands to millions of extents, so mostly
this isn't noticed.
However, trying to run things like xfs_mdrestore of large filesystem
dumps on a debug kernel quickly becomes impossible as the CPU is
completely burnt up repeatedly walking the sparse file bmapbt that
is generated for every allocation that is made.
Hence, if the file has more than 10,000 extents, just don't bother
with walking the tree to check it exhaustively. The btree code has
checks that ensure that the newly inserted/removed/modified record
is correctly ordered, so the entrie tree walk in thses cases has
limited additional value.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
This allows us to see page cache driven readahead in action as it
passes through XFS. This helps to understand buffered read
throughput problems such as readahead IO IO sizes being too small
for the underlying device to reach max throughput.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
* bugfixes:
SUNRPC: Fixup socket wait for memory
SUNRPC: Fix a missing break in rpc_anyaddr()
pNFS/flexfiles: Fix an Oopsable typo in ff_mirror_match_fh()
NFS: Fix attribute cache revalidation
NFS: Ensure we revalidate attributes before using execute_ok()
NFS: Flush reclaim writes using FLUSH_COND_STABLE
NFS: Background flush should not be low priority
NFSv4.1/pnfs: Fixup an lo->plh_block_lgets imbalance in layoutreturn
NFSv4: Don't perform cached access checks before we've OPENed the file
NFS: Allow the combination pNFS and labeled NFS
NFS42: handle layoutstats stateid error
nfs: Fix race in __update_open_stateid()
nfs: fix missing assignment in nfs4_sequence_done tracepoint
The use of wait_on_atomic_t() for waiting on I/O to complete before
unlocking allows us to git rid of the NFS_IO_INPROGRESS flag, and thus the
nfs_iocounter's flags member, and finally the nfs_iocounter altogether.
The count of I/O is moved to the lock context, and the counter
increment/decrement functions become simple enough to open-code.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
[Trond: Fix up conflict with existing function nfs_wait_atomic_killable()]
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
As of the 4.3 kernel release, the fitrim ioctl can now discard any region
of a disk that is not allocated to any chunk/block group, including the
first megabyte which is used for our primary superblock and by the boot
loader (grub for example).
Fix this by not allowing to trim/discard any region in the device starting
with an offset not greater than min(alloc_start_mount_option, 1Mb), just
as it was not possible before 4.3.
A reproducer test case for xfstests follows.
seq=`basename $0`
seqres=$RESULT_DIR/$seq
echo "QA output created by $seq"
tmp=/tmp/$$
status=1 # failure is the default!
trap "_cleanup; exit \$status" 0 1 2 3 15
_cleanup()
{
cd /
rm -f $tmp.*
}
# get standard environment, filters and checks
. ./common/rc
. ./common/filter
# real QA test starts here
_need_to_be_root
_supported_fs btrfs
_supported_os Linux
_require_scratch
rm -f $seqres.full
_scratch_mkfs >>$seqres.full 2>&1
# Write to the [0, 64Kb[ and [68Kb, 1Mb[ ranges of the device. These ranges are
# reserved for a boot loader to use (GRUB for example) and btrfs should never
# use them - neither for allocating metadata/data nor should trim/discard them.
# The range [64Kb, 68Kb[ is used for the primary superblock of the filesystem.
$XFS_IO_PROG -c "pwrite -S 0xfd 0 64K" $SCRATCH_DEV | _filter_xfs_io
$XFS_IO_PROG -c "pwrite -S 0xfd 68K 956K" $SCRATCH_DEV | _filter_xfs_io
# Now mount the filesystem and perform a fitrim against it.
_scratch_mount
_require_batched_discard $SCRATCH_MNT
$FSTRIM_PROG $SCRATCH_MNT
# Now unmount the filesystem and verify the content of the ranges was not
# modified (no trim/discard happened on them).
_scratch_unmount
echo "Content of the ranges [0, 64Kb] and [68Kb, 1Mb[ after fitrim:"
od -t x1 -N $((64 * 1024)) $SCRATCH_DEV
od -t x1 -j $((68 * 1024)) -N $((956 * 1024)) $SCRATCH_DEV
status=0
exit
Reported-by: Vincent Petry <PVince81@yahoo.fr>
Reported-by: Andrei Borzenkov <arvidjaar@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=109341
Fixes: 499f377f49 (btrfs: iterate over unused chunk space in FITRIM)
Cc: stable@vger.kernel.org # 4.3+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
The nlmsvc_binding structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
When converting a filesystem via balance check that metadata mode
is at least as redundant as the data mode. For example give warning
when:
-dconvert=raid1 -mconvert=single
Signed-off-by: Sam Tygier <samtygier@yahoo.co.uk>
[ minor message reformatting ]
Signed-off-by: David Sterba <dsterba@suse.com>
There is one ENOSPC case that's very confusing. There's Available
greater than zero but no file operation succeds (besides removing
files). This happens when the metadata are exhausted and there's no
possibility to allocate another chunk.
In this scenario it's normal that there's still some space in the data
chunk and the calculation in df reflects that in the Avail value.
To at least give some clue about the ENOSPC situation, let statfs report
zero value in Avail, even if there's still data space available.
Current:
/dev/sdb1 4.0G 3.3G 719M 83% /mnt/test
New:
/dev/sdb1 4.0G 3.3G 0 100% /mnt/test
We calculate the remaining metadata space minus global reserve. If this
is (supposedly) smaller than zero, there's no space. But this does not
hold in practice, the exhausted state happens where's still some
positive delta. So we apply some guesswork and compare the delta to a 4M
threshold. (Practically observed delta was 2M.)
We probably cannot calculate the exact threshold value because this
depends on the internal reservations requested by various operations, so
some operations that consume a few metadata will succeed even if the
Avail is zero. But this is better than the other way around.
Signed-off-by: David Sterba <dsterba@suse.com>
We can also preallocate btrfs_path that's used during pending snapshot
creation and avoid another late ENOMEM failure.
Signed-off-by: David Sterba <dsterba@suse.com>
The actual snapshot creation is delayed until transaction commit. If we
cannot get enough memory for the root item there, we have to fail the
whole transaction commit which is bad. So we'll allocate the memory at
the ioctl call and pass it along with the pending_snapshot struct. The
potential ENOMEM will be returned to the caller of snapshot ioctl.
Signed-off-by: David Sterba <dsterba@suse.com>
The values of btrfs_path::locks are 0 to 4, fit into a u8. Let's see:
* overall size of btrfs_path drops down from 136 to 112 (-24 bytes),
* better packing in a slab page +6 objects
* the whole structure now fits to 2 cachelines
* slight decrease in code size:
text data bss dec hex filename
938731 43670 23144 1005545 f57e9 fs/btrfs/btrfs.ko.before
938203 43670 23144 1005017 f55d9 fs/btrfs/btrfs.ko.after
(and the generated assembly does not change much)
The main purpose is to decrease the size of the structure without
affecting performance. The byte access is usually well behaving accross
arches, the locks are not accessed frequently and sometimes just
compared to zero.
Note for further size reduction attempts: the slots could be made u16
but this might generate worse code on some arches (non-byte and non-int
access). Also the range of operations on slots is wider compared to
locks and the potential performance drop should be evaluated first.
Signed-off-by: David Sterba <dsterba@suse.com>
The level is 0..7, we can use smaller type. The size of btrfs_path is now
136 bytes from 144, which is +2 objects that fit into a 4k slab.
Signed-off-by: David Sterba <dsterba@suse.com>
The possible values for reada are all positive and bounded, we can later
save some bytes by storing it in u8.
Signed-off-by: David Sterba <dsterba@suse.com>
Replace the integers by enums for better readability. The value 2 does
not have any meaning since a717531942
"Btrfs: do less aggressive btree readahead" (2009-01-22).
Signed-off-by: David Sterba <dsterba@suse.com>
There are a few statically initialized arrays that can be made const.
The remaining (like file_system_type, sysfs attributes or prop handlers)
do not allow that due to type mismatch when passed to the APIs or
because the structures are modified through other members.
Signed-off-by: David Sterba <dsterba@suse.com>
Preparatory work for making btrfs_free_space_op constant. In
test_steal_space_from_bitmap_to_extent, we substitute use_bitmap with
own version thus preventing constification. We can rework it so we
replace the whole structure with the correct function pointers.
Signed-off-by: David Sterba <dsterba@suse.com>
Use list_for_each_entry*() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Use list_for_each_entry_safe() instead of list_for_each_safe() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Use list_for_each_entry*() instead of list_for_each*() to simplify
the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We use many constants to represent size and offset value. And to make
code readable we use '256 * 1024 * 1024' instead of '268435456' to
represent '256MB'. However we can make far more readable with 'SZ_256MB'
which is defined in the 'linux/sizes.h'.
So this patch replaces 'xxx * 1024 * 1024' kind of expression with
single 'SZ_xxxMB' if 'xxx' is a power of 2 then 'xxx * SZ_1M' if 'xxx' is
not a power of 2. And I haven't touched to '4096' & '8192' because it's
more intuitive than 'SZ_4KB' & 'SZ_8KB'.
Signed-off-by: Byongho Lee <bhlee.kernel@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It's slightly cleaner to zero-out the delayed node upon allocation
than to do it by hand in btrfs_init_delayed_node() for a few members
Signed-off-by: Alexandru Moise <00moses.alexander00@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Alexandru Moise <00moses.alexander00@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Conform to __btrfs_fs_incompat() cast-to-bool (!!) by explicitly
returning boolean not int.
Signed-off-by: Alexandru Moise <00moses.alexander00@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The inode argument is never used from the beginning, so remove it.
Signed-off-by: Byongho Lee <bhlee.kernel@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Although we prefer to use separate caches for various structs, it seems
better not to do that for struct btrfs_delalloc_work. Objects of this
type are allocated rarely, when transaction commit calls
btrfs_start_delalloc_roots, requesting delayed iputs.
The objects are temporary (with some IO involved) but still allocated
and freed within __start_delalloc_inodes. Memory allocation failure is
handled.
The slab cache is empty most of the time (observed on several systems),
so if we need to allocate a new slab object, the first one has to
allocate a full page. In a potential case of low memory conditions this
might fail with higher probability compared to using the generic slab
caches.
Signed-off-by: David Sterba <dsterba@suse.com>
We can handle the special case of num_stripes == 0 directly inside
btrfs_read_sys_array. The BUG_ON in btrfs_chunk_item_size is there to
catch other unhandled cases where we fail to validate external data.
A crafted or corrupted image crashes at mount time:
BTRFS: device fsid 9006933e-2a9a-44f0-917f-514252aeec2c devid 1 transid 7 /dev/loop0
BTRFS info (device loop0): disk space caching is enabled
BUG: failure at fs/btrfs/ctree.h:337/btrfs_chunk_item_size()!
Kernel panic - not syncing: BUG!
CPU: 0 PID: 313 Comm: mount Not tainted 4.2.5-00657-ge047887-dirty #25
Stack:
637af890 60062489 602aeb2e 604192ba
60387961 00000011 637af8a0 6038a835
637af9c0 6038776b 634ef32b 00000000
Call Trace:
[<6001c86d>] show_stack+0xfe/0x15b
[<6038a835>] dump_stack+0x2a/0x2c
[<6038776b>] panic+0x13e/0x2b3
[<6020f099>] btrfs_read_sys_array+0x25d/0x2ff
[<601cfbbe>] open_ctree+0x192d/0x27af
[<6019c2c1>] btrfs_mount+0x8f5/0xb9a
[<600bc9a7>] mount_fs+0x11/0xf3
[<600d5167>] vfs_kern_mount+0x75/0x11a
[<6019bcb0>] btrfs_mount+0x2e4/0xb9a
[<600bc9a7>] mount_fs+0x11/0xf3
[<600d5167>] vfs_kern_mount+0x75/0x11a
[<600d710b>] do_mount+0xa35/0xbc9
[<600d7557>] SyS_mount+0x95/0xc8
[<6001e884>] handle_syscall+0x6b/0x8e
Reported-by: Jiri Slaby <jslaby@suse.com>
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
CC: stable@vger.kernel.org # 3.19+
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_delayed_extent_op can be packed in a better way, it's 40 bytes now
and has 8 unused bytes. Reducing the level type to u8 makes it possible
to squeeze it to the padding byte after key. The bitfields were switched
to bool as there's space to store the full byte without increasing the
whole structure, besides that the generated assembly is smaller.
struct btrfs_delayed_extent_op {
struct btrfs_disk_key key; /* 0 17 */
u8 level; /* 17 1 */
bool update_key; /* 18 1 */
bool update_flags; /* 19 1 */
bool is_data; /* 20 1 */
/* XXX 3 bytes hole, try to pack */
u64 flags_to_set; /* 24 8 */
/* size: 32, cachelines: 1, members: 6 */
/* sum members: 29, holes: 1, sum holes: 3 */
/* last cacheline: 32 bytes */
};
The final size is 32 bytes which gives +26 object per slab page.
text data bss dec hex filename
938811 43670 23144 1005625 f5839 fs/btrfs/btrfs.ko.before
938747 43670 23144 1005561 f57f9 fs/btrfs/btrfs.ko.after
Signed-off-by: David Sterba <dsterba@suse.com>
Inodes for delayed iput allocate a trivial helper structure, let's place
the list hook directly into the inode and save a kmalloc (killing a
__GFP_NOFAIL as a bonus) at the cost of increasing size of btrfs_inode.
The inode can be put into the delayed_iputs list more than once and we
have to keep the count. This means we can't use the list_splice to
process a bunch of inodes because we'd lost track of the count if the
inode is put into the delayed iputs again while it's processed.
Signed-off-by: David Sterba <dsterba@suse.com>
Since we will add support for -d dup for non-mixed filesystem,
kernel need to support converting to this raid-type.
This patch remove limitation of above case.
Tested by following script:
(combination of dup conversion with fsck):
export TEST_DEV='/dev/vdc'
export TEST_DIR='/var/ltf/tester/mnt'
do_dup_test()
{
local m_from="$1"
local d_from="$2"
local m_to="$3"
local d_to="$4"
echo "Convert from -m $m_from -d $d_from to -m $m_to -d $d_to"
umount "$TEST_DIR" &>/dev/null
./mkfs.btrfs -f -m "$m_from" -d "$d_from" "$TEST_DEV" >/dev/null || return 1
mount "$TEST_DEV" "$TEST_DIR" || return 1
cp -a /sbin/* "$TEST_DIR"
[[ "$m_from" != "$m_to" ]] && {
./btrfs balance start -f -mconvert="$m_to" "$TEST_DIR" || return 1
}
[[ "$d_from" != "$d_to" ]] && {
local opt=()
[[ "$d_to" == single ]] && opt+=("-f")
./btrfs balance start "${opt[@]}" -dconvert="$d_to" "$TEST_DIR" || return 1
}
umount "$TEST_DIR" || return 1
./btrfsck "$TEST_DEV" || return 1
echo
return 0
}
test_all()
{
for m_from in single dup; do
for d_from in single dup; do
for m_to in single dup; do
for d_to in single dup; do
do_dup_test "$m_from" "$d_from" "$m_to" "$d_to" || return 1
done
done
done
done
}
test_all
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We hit this panic on a few of our boxes this week where we have an
ordered_extent with an NULL inode. We do an igrab() of the inode in writepages,
but weren't doing it in writepage which can be called directly from the VM on
dirty pages. If the inode has been unlinked then we could have I_FREEING set
which means igrab() would return NULL and we get this panic. Fix this by trying
to igrab in btrfs_writepage, and if it returns NULL then just redirty the page
and return AOP_WRITEPAGE_ACTIVATE; so the VM knows it wasn't successful. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Looks like oversight, call brelse() when checksum fails. Further down the
code, in the non error path, we do call brelse() and so we don't see
brelse() in the goto error paths.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
make sure the isize we read doesn't change during the process.
Signed-off-by: Fan li <fanofcode.li@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
There was a subtle bug on nat cache management which incurs wrong nid allocation
or wrong block addresses when try_to_free_nats is triggered heavily.
This patch enlarges the previous coverage of nat_tree_lock to avoid data race.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Use to_delayed_work() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If we failed to create a hard link we were not always releasing the
the transaction handle we got before, resulting in a memory leak and
preventing any other tasks from being able to commit the current
transaction.
Fix this by always releasing our transaction handle.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
gendisk with part==0 is obviously gendisk->disk_name.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Number of fds is already known based on passed list.
No functional changes.
Signed-off-by: Mateusz Guzik <mguzik@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
XFS now uses CRC verification over a limited section of the log to
detect torn writes prior to a crash. This is difficult to test directly
due to the timing and hardware requirements to cause a short write.
Add a mechanism to inject CRC errors into log records to facilitate
testing torn write detection during log recovery. This mechanism is
dangerous and can result in filesystem corruption. Thus, it is only
available in DEBUG mode for testing/development purposes. Set a non-zero
value to the following sysfs entry to enable error injection:
/sys/fs/xfs/<dev>/log/log_badcrc_factor
Once enabled, XFS intentionally writes an invalid CRC to a log record at
some random point in the future based on the provided frequency. The
filesystem immediately shuts down once the record has been written to
the physical log to prevent metadata writeback (e.g., AIL insertion)
once the log write completes. This helps reasonably simulate a torn
write to the log as the affected record must be safe to discard. The
next mount after the intentional shutdown requires log recovery and
should detect and recover from the torn write.
Note again that this _will_ result in data loss or worse. For testing
and development purposes only!
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Certain types of storage, such as persistent memory, do not provide
sector atomicity for writes. This means that if a crash occurs while XFS
is writing log records, only part of those records might make it to the
storage. This is problematic because log recovery uses the cycle value
packed at the top of each log block to locate the head/tail of the log.
This can lead to CRC verification failures during log recovery and an
unmountable fs for a filesystem that is otherwise consistent.
Update log recovery to incorporate log record CRC verification as part
of the head/tail discovery process. Once the head is located via the
traditional algorithm, run a CRC-only pass over the records up to the
head of the log. If CRC verification fails, assume that the records are
torn as a matter of policy and trim the head block back to the start of
the first bad record.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
* pnfs_generic:
NFSv4.1/pNFS: Cleanup constify struct pnfs_layout_range arguments
NFSv4.1/pnfs: Cleanup copying of pnfs_layout_range structures
NFSv4.1/pNFS: Cleanup pnfs_mark_matching_lsegs_invalid()
NFSv4.1/pNFS: Fix a race in initiate_file_draining()
NFSv4.1/pNFS: pnfs_error_mark_layout_for_return() must always return layout
NFSv4.1/pNFS: pnfs_mark_matching_lsegs_return() should set the iomode
NFSv4.1/pNFS: Use nfs4_stateid_copy for copying stateids
NFSv4.1/pNFS: Don't pass stateids by value to pnfs_send_layoutreturn()
NFS: Relax requirements in nfs_flush_incompatible
NFSv4.1/pNFS: Don't queue up a new commit if the layout segment is invalid
NFS: Allow multiple commit requests in flight per file
NFS/pNFS: Fix up pNFS write reschedule layering violations and bugs
NFSv4: List stateid information in the callback tracepoints
NFSv4.1/pNFS: Don't return NFS4ERR_DELAY unnecessarily in CB_LAYOUTRECALL
NFSv4.1/pNFS: Ensure we enforce RFC5661 Section 12.5.5.2.1
pNFS: If we have to delay the layout callback, mark the layout for return
NFSv4.1/pNFS: Add a helper to mark the layout as returned
pNFS: Ensure nfs4_layoutget_prepare returns the correct error
Peng Tao points out that the call to pnfs_mark_matching_lsegs_return()
could race with pnfs_put_lseg(), in which case the layout segment is
cleared, but no layoutreturn will be sent.
Fix is to replace the call to pnfs_mark_matching_lsegs_invalid().
Reported-by: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Fix a bug whereby if all the layout segments could be immediately freed,
the call to pnfs_error_mark_layout_for_return() would never result in
a layoutreturn.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
If pnfs_mark_matching_lsegs_return() needs to mark a layout segment for
return, then it must also set the return iomode.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
get_zeroed_page does alloc_page and returns page_address of the result;
subsequent virt_to_page will recover the page, but since the caller
needs both page and its page_address() anyway, why bother going through
that wrapper at all?
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
A _lot_ of ->write() instances were open-coding it; some are
converted to memdup_user_nul(), a lot more remain...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If a name contains at least some characters with Unicode values
exceeding single byte, the CS0 output should have 2 bytes per character.
And if other input characters have single byte Unicode values, then
the single input byte is converted to 2 output bytes, and the length
of output becomes larger than the length of input. And if the input
name is long enough, the output length may exceed the allocated buffer
length.
All this means that conversion from UTF8 or NLS to CS0 requires
checking of output length in order to stop when it exceeds the given
output buffer size.
[JK: Make code return -ENAMETOOLONG instead of silently truncating the
name]
CC: stable@vger.kernel.org
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Jan Kara <jack@suse.cz>
udf_CS0toUTF8 function stops the conversion when the output buffer
length reaches UDF_NAME_LEN-2, which is correct maximum name length,
but, when checking, it leaves the space for a single byte only,
while multi-bytes output characters can take more space, causing
buffer overflow.
Similar error exists in udf_CS0toNLS function, that restricts
the output length to UDF_NAME_LEN, while actual maximum allowed
length is UDF_NAME_LEN-2.
In these cases the output can override not only the current buffer
length field, causing corruption of the name buffer itself, but also
following allocation structures, causing kernel crash.
Adjust the output length checks in both functions to prevent buffer
overruns in case of multi-bytes UTF8 or NLS characters.
CC: stable@vger.kernel.org
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Jan Kara <jack@suse.cz>
ConfigFS lacked binary attributes up until now. This patch
introduces support for binary attributes in a somewhat similar
manner of sysfs binary attributes albeit with changes that
fit the configfs usage model.
Problems that configfs binary attributes fix are everything that
requires a binary blob as part of the configuration of a resource,
such as bitstream loading for FPGAs, DTBs for dynamically created
devices etc.
Look at Documentation/filesystems/configfs/configfs.txt for internals
and howto use them.
This patch is against linux-next as of today that contains
Christoph's configfs rework.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[hch: folded a fix from Geert Uytterhoeven <geert+renesas@glider.be>]
[hch: a few tiny updates based on review feedback]
Signed-off-by: Christoph Hellwig <hch@lst.de>
The qtree_fmt_operations structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jan Kara <jack@suse.cz>
A new warning has come up from a recent cleanup:
fs/udf/inode.c: In function 'udf_setup_indirect_aext':
fs/udf/inode.c:1927:28: warning: 'adsize' may be used uninitialized in this function [-Wmaybe-uninitialized]
If the alloc_type is neither ICBTAG_FLAG_AD_SHORT nor
ICBTAG_FLAG_AD_LONG, the value of adsize is undefined. Currently,
callers of these functions make sure alloc_type is one of the two valid
ones but for future proofing make sure we handle the case of invalid
alloc type as well. This changes the code to return -EIOin that case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: fcea62babc ("udf: Factor out code for creating indirect extent")
Signed-off-by: Jan Kara <jack@suse.cz>
Dan Williams