Some old AD codecs don't like the independent HP handling, either it
contains a single DAC (AD1981) or it mandates the mixer routing
(AD1986A). This patch removes the indep_hp flag for such codecs.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=68081
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCI devices with DMA masks smaller than 32bit should enable
CONFIG_ZONE_DMA. Since the recent change of page allocator, page
allocations via dma_alloc_coherent() with the limited DMA mask bits
may fail more frequently, ended up with no available buffers, when
CONFIG_ZONE_DMA isn't enabled. With CONFIG_ZONE_DMA, the system has
much more chance to obtain such pages.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=68221
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The failures of buffer preallocations at driver initializations aren't
critical but it's still helpful to inform, so that user can know that
something doesn't work as expected.
For example, the recent page allocator change triggered regressions,
but developers didn't notice until recently because the driver didn't
complain.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch implements a device-tree-only CPU DAI driver for Freescale ESAI
controller that supports:
- 12 channels playback and 8 channels record.
[ Some of the inner transmitters and receivers are sharing same group of
pins. So the maxmium 12 output or 8 input channels are only valid if
there is no pin conflict occurring to it. ]
- Independent (asynchronous mode) or shared (synchronous mode) transmit and
receive sections with separate or shared internal/external clocks and frame
syncs, operating in Master or Slave mode.
[ Current ALSA seems not to allow CPU DAI drivers to configure DAI format
separately for PLAYBACK and CAPTURE. So this first version only supports
the case that uses the same DAI format for both directions. ]
- Various DAI formats: I2S, Left-Justified, Right-Justified, DSP-A and DSP-B.
- Programmable word length (8, 16, 20 or 24bits)
- Flexible selection between system clock or external oscillator as input
clock source, programmable internal clock divider and frame sync generation.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add controls to enable/disable the headphone short circuit protection of
the headphone outputs.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Occasionally, on playback stream ringbuffer wraparound, the EMU20K1
hardware will momentarily return 0 instead of the proper current(loop)
address. This patch handles that case, fixing the problem of playback
position corruption and subsequent loss of buffered sound data, that
occurs with some common buffering layout patterns(e.g. multiple
simultaneous output streams with differently-sized or
non-power-of-2-sized buffers).
An alternate means of fixing the problem would be to read the ca
register continuously, until two sequential reads return the same
value; however, that would be a more invasive change, has performance
implications, and isn't necessary unless there are also issues with the
value not being updated atomically in regards to individual bits or
something similar(which I have not encountered through light testing).
I have no EMU20K2 hardware to confirm if the issue is present there,
but even if it's not, this change shouldn't break anything that's not
already broken.
Signed-off-by: Sarah Bessmer <aotos@fastmail.fm>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the dt is used and the cinfo is NULL, the -ENOMEM should be return.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
If the dt is not used, the cinfo will be always NULL before using it.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For those platforms using DAI master mode like I2S, it's better to pre-set
a default slot number so that there's no need for these common cases to set
the slot number from its machine driver any more.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add the missing clk_disable_unprepare() before return from
fsl_ssi_probe() in the request irq error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some DMA cores might add additional restrictions on which in memory audio
formats can be supported by the compound sound card. If the PCM component
specifies a set of formats it supports (by setting the formats field to non 0)
take these into account when calculating the format set for the compound sound
card.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
single_open requires a function with signature
'int (*)(struct seq_file *, void *)'. This patch fixes the warning by
fixing the wrong return type of fsl_ssi_stats_show.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of keeping a separate snd-page-alloc module, merge into the
core snd-pcm module, as we don't need to keep it as an individual
module due to the drop of page reservation.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Nowadays we have CMA for obtaining the contiguous memory pages
efficiently. Let's kill the old kludge for reserving the memory pages
for large buffers. It was rarely useful (only for preserving pages
among module reloading or a little help by an early boot scripting),
used only by a couple of drivers, and yet it gives too much ugliness
than its benefit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Broadwell and Haswell have the same behavior on display audio. So this patch
defines is_haswell_plus() to include codecs for both Haswell and its successor
Broadwell, and apply all Haswell fix-ups to Broadwell.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x80862808) and module alias for Broadwell
display codec.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the device ID for Intel Broadwell display HD-Audio controller,
and applies Haswell properties to this device.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_SND_SOC_DMAENGINE_PCM was renamed to CONFIG_SND_DMAENGINE_PCM
recently. And yet we don't have to select it since
CONFIG_SND_GENERIC_DMAENGINE_PCM selects the dependency by itself, so
just rip it off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move the start of booting the DSP to earlier in the DAPM process, and
move the final starting of the DSP to later in the DAPM process. This
allows us to overlap some of the processing with other components of the
system being brought up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move the ADSP2 boot proceedure into a work structure in preparation for
running it asynchronously with the reset of the audio path bring up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The normal trigger function can now be used for AC97. Drop AC97 trigger
function.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch defines the appropriate register values for different
oparation modes and IP versions. We have to handle DMA/FIQ, AC97,
DEBUG-IRQs and offline/online configuration support.
With this patch we cleanup some driver code that was not reference
manual conform and try to cleanup the whole trigger function to seperate
the actual register values from the enable/disable logic, which is now
hidden in fsl_ssi_config helpers.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a struct 'fsl_ssi_rxtx_reg_val' which holds register
values necessary to enable rx/tx. Based on those preset register values,
the added configuration functions will cleanly enable/disable different
parts of the SSI IP while supporting online/offline configuration.
Different operating modes can be setup directly as different register
values in fsl_ssi_reg_val.
These functions and structs will help to cleanup and simplify the
trigger function to support many different IP versions (online/offline
configuration) and different operating modes.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
imx50-ssi and later versions of this IP support online reconfiguration
of all registers. The reference manual does not list any registers that
can only be configured while the SSI unit is disabled. This patch
introduces the flag for later use.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
irqs should only be requested/released with enabled DMA. Previously
interrupt statistics where disabled for IMX Processors because of
different writeable SISR bits.
This patch introduces support for irqstats on imx processors again by
creating a sisr writeback mask and introducing a imx35-ssi compatible.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a small but significant difference between imx21-ssi and
imx51-ssi and above. imx21-ssi does not allow online reconfiguration of
some registers. They have to be configured at the beginning.
imx51-ssi has to reconfigure the SSI unit while it is running. Otherwise
it would not be possible to have two streams in parallel. The new SDMA
unit in imx51 and above has to be configured before the first DMA
request arrives. Therefor we need to setup TDMAE/RDMAE just before
starting the stream.
This patch introduces distinct imx51-ssi as compatible and adds
of_device_id matching in the probe function.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Interrupt statistics of fsl_ssi are mainly for debugging purpose. Most
of those interrupts show error states, e.g. under/overflow.
The stats should be exposed via debugfs instead of sysfs.
This patch moves the statistics file to debugfs.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes the error handling in the fsl-ssi probe function.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Both patch_realtek.c and patch_conexant.c contain the fairy same code
snippet for supporting Thinkpad ACPI LED controls. Split them into
thinkpad_helper.c and include it from both places. Although this
isn't the best approach from the code size POV, the probability for
coexistence of both Realtek and Conexant codecs on a single machine is
pretty low, thus it'll end up with less memory footprint than
splitting to yet another module.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SSM260x also supports 16kHz with external master clocks of 12.000MHz,
12.288MHz and 18.432MHz.
Add matching coefficients, update constraints and announced rates.
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
To avoid another lookup for the twl4030_priv in there.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There's no other users of this functionality, the code can be moved inside
of twl4030_write.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Over time the multi line alignment got messed up. Correct them in one go
so the code will look consistent.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Depend on the regmap reg cache implementation for register caching done in
the twl-core driver.
The local register cache can be removed and we can keep only shadow copies
of certain ctl registers for pop noise reduction.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Few registers need to be cached in the codec driver level. These registers
should only be written when the path is active to avoid pop noise on the
given path.
This patch adds an array which covers the range where the sensitive registers
are located and uppon loadinf the driver the ctl cache will be initialized.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The register states now tracked by the regmap implementation in the core which
makes the reset registers functionality 'redundant' since we know the state
of the registers now all the time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No need to keep the check defaults functionality anymore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simplifies the code a bit and prepares it to the removal of local caching.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes the following sparse warning:
sound/soc/ux500/ux500_msp_i2s.c:649:5: warning:
symbol 'ux500_msp_i2s_of_init_msp' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver defines ADAU1701_SEROCTL_WORD_LEN_16 as 0x10 while it should be b10,
so 0x2. This patch fixes it.
Reported-by: Magnus Reftel <magnus.reftel@lockless.no>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Connect the DAPM graph through each BE DAI link to the componnent(s) on the
other side of the BE DAI link. This allows the graph to be walked on
both sides of the link when graph changes are made.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Provide a quick way to tell if a DAI is a dummy DAI or a regular DAI.
This is for internal DAPM usage only and is used to determine whether to
insert a DAI link connection into the DAPM graph.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
AD1986A mic pins (0x1d and 0x1f) share the same widget for controlling
the loopback volume/mute, but the generic parser didn't check it.
This ended up with the duplicated controls for the same effect.
This patch adds the check of the duplication for avoiding it.
After this fix, there will be only one control although it affects
both paths; this remaining issue should be fixed later in a different
patch.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66621
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The 3stack pin configs for AD1986A codec had incorrect values that
resulted in broken mic and line-in.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66621
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some tags used in the firmware patch file are inconsistent with hwdep
sysfs file names, such as, the firmware patch takes [hint] tag while
sysfs file is */hints. This makes even me referring back to the
document often. Let's provide the same tag names as sysfs for
reducing confusions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just a code refactoring: the need_codec flag in hda_patch_item struct
can be removed by checking the current mode instead. No functional
change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turned out that some AMD HDMI controllers still don't provide
proper values in GCAP register (all zero), and the driver assigns only
one stream in that case, although the connected codec chip supports
more than one stream.
In this patch, the default max number of streams for AMD HDMI
controllers is increased to 8, which should suffice for most use
cases. The overhead by this increase is more azx_dev struct and BDL
allocations, so it's negligible. Of course, if the controller
provides a proper GCAP register, the register value would be used.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some BE DAIs can be "dummy" (when the DSP is controlling the DAI) and as such
wont have set a minimum number of playback or capture channels required for BE
DAI registration (to establish supported stream directions).
Force machine drivers to explicitly set whether they support playback and capture
stream directions for every BE DAIs.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the platform driver has no ops, the platform function
bespoke_trigger() is no more called.
The problem was introduced by the commit c5914b0aae
"ASoC: pcm: Check for ops before deferencing them"
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
Even though we might not have rigor rule for the simple card property names,
according to the existing ones, they are all in a same pattern:
[simple-audio-card,]XXX;
Rename simple-audio-routing to simple-audio-card,routing, and make the simple
card's properties has one unified name.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We no longer have a means to differentiate between MSP devices at probe
time, mainly because we don't really have to. So rather than have an over-
sized static data structure in place, where the only difference between
devices is the ID and name (which are unused), we'll just create one
succinct, statically assigned and shared one instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
If booting with full DT support (i.e. DMA too, the last piece of the
puzzle), then we don't need to use the compatible_request_channel call
back or require some of the historical bumph which probably isn't
required by a platform data start-up now either. This will also be
ripped out in upcoming commits.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In this patch we do two things. Firstly, instead of open coding the
store of DMA data in to the DAI for later use, we use the API provided.
Secondly we create and store similar DMA data for the DT case, only
this time we use 'struct snd_dmaengine_dai_dma_data' which is provided
by the core for this very reason.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Soon we will strip out pdata support from the Ux500 set of ASoC drivers.
When this happens it will have to supply a DMA slave_config to the
dmaengine. At the moment a great deal of this comes from pdata via
AUXDATA. We need to become independent of this soon. This patch starts
the process by allocating memory for the associated data structures and
fetches the MSP id used for const struct indexing.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In preparation for full Device Tree enablement we must differentiate
between the two varying ways DMA data can be held in the DAI store. If
we're booting with Device Tree the provided 'snd_dmaengine_dai_dma_data'
data structure shall be used, whereas in order to avoid breaking legacy
platform data we also need to be able to translate DMA data stored using
the UX500 specific 'ux500_msp_dma_params' method.
Once we move over to solely use Device Tree, we can enforce the use of
'snd_dmaengine_dai_dma_data' and this code can be removed altogether.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Slave Config's addr_width attribute is populated by data_width of
dma_cfg, which in turn is derived from dma_params' data_size attribute
and that comes from the slot_width which is always 16 bits (2 Bytes).
We're cutting out the middle man here and just setting the DMA Slave
Config directly.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
We're getting closer to fully enabling the Ux500 ASoC driver for Device
Tree. When we switch over from using AUXDATA we'll need to match platform
by only Device Tree nodes. In this patch we NULL out the platform_name,
and supply nodes for each platform device.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
These drivers will not work without platform specific data, which is
passed in via Device Tree or Platform Data. To avoid the chance of
NULL pointer dereferencing and alike, let's ensure we have at least
one of the methods in play before continuing.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 7b11304 ("dma: mxs-dma: Report correct residue for cyclic DMA")
the mxs dmaengine driver has support for residue reporting. So there is no need
to specify the SND_DMAENGINE_PCM_FLAG_NO_RESIDUE flag anymore. This allows a
finer grained resolution for the PCM pointer as well as avoids the race
condition that can occur with the period counting that is used when the
dmaengine driver does not support residue reporting.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 6873ee464a (ASoC: fsl_ssi: Fix printing return code on clk error) caused
the following build warning:
sound/soc/fsl/fsl_ssi.c: In function 'fsl_ssi_probe':
sound/soc/fsl/fsl_ssi.c:1196:6: warning: format '%d' expects argument of type 'int', but argument 3 has type 'long int' [-Wformat]
Fix it by using '%ld' to print the 'long int' format.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Allow PCMs that do not impose any restrictions on the supported formats to set
the formats field to 0, Instead of assuming that this means that the PCM does
not support any formats (which doesn't make much sense), assume that it supports
all formats. This brings the behavior of DPCM closer to that of non-DPCM.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have the same code for initializing the runtime pcm on both the playback and
the capture path. Factor this out into a common helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is a trivial cleanup: remove useless variable mc13xxx and
extra spaces. No functional changes.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are no users of this driver without pdata, so stop using
constant assignment of ADC and DAC ports.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
mc13783-codec is probed only by MC13XXX MFD core driver so
use module_platform_driver_probe().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Mark Brown