Load switches are modeled as regulators but they just provide
the voltage of their parent input supply. So the drivers for
these switches usually don't provide a .get_voltage function
handler but there is code in the kernel that assumes that all
regulators should be able to provide its current voltage rail.
So, if the output voltage for a regulator is not available and
it has a parent supply, then pass the voltage of its parent.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
With commit 064d5cd110
(regulator: core: Fix the init of DT defined fixed regulators)
We ensure that regulator must be capable of providing it's current
voltage when constraints are used, however adding the return value in
the print is a little more informative to explain the nature of the
failure involved.
So, instead of providing message such as:
smps9: failed to get the current voltage
having error value added to the message such as:
smps9: failed to get the current voltage(-22)
is a little more informative for debugging the error.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When a regulator is defined using DT and it has a single voltage the
regulator init always tries to apply this voltage. However it fails if
the regulator isn't settable because it is using an internal low level
function. To overcome this we now first query the regulator and only
set it if needed.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
regulator_init_complete does a scan of regulators which dont have
always-on or consumers are automatically disabled as being unused.
However, with deferred probing, late_initcall() is too soon to
declare a regulator as unused as the regulator itself might not
have registered due to defferal - Example: A regulator deffered due
to i2bus not available which in turn is deffered due to pinctrl
availability.
Since deferred probing is done in late_initcall(), do the cleanup of
unused regulators by regulator_init_complete in late_initcall_sync
instead of late_initcall.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
[nm@ti.com: minor rewording]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the spirit of conservatism that governs our general approach to
permissions it is better if we don't touch regulators we weren't explicitly
given permissions to control. This avoids the need to explicitly specify
unknown regulators in DT as always on, if a regulator is not otherwise
involved in software control it can be omitted from the DT.
Regulators explicitly given constraints in DT still need to have an always
on constraint specified as before.
Signed-off-by: Mark Brown <broonie@linaro.org>
The voltages in axp20x_ldo4_data table are in ascendant order, so use
regulator_map_voltage_ascend.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use more compact of_property_read_{bool|u32}() calls instead of the
of_{find|get}_property() calls in of_get_regulation_constraints() where
possible (note that of_property_read_{bool|u32}() were already used to read
some properties).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
regulator_get_optional() doesn't hold an exclusive reference to
the regulator. Fix the documentation and reword the exclusive
documentation to fix the grammatical error "this reference is
held".
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
commit 2cce4be9e6 "regulator: arizona-ldo1: Add processing of init_data
from device tree" added a call to of_get_child_by_name() but
did not add an #include to the header file declaring that function.
I got a build error when doing randconfig testing on this, which
is fixed by this patch to include of.h.
drivers/regulator/arizona-ldo1.c:192:2: error: implicit declaration of function 'of_get_child_by_name' [-Werror=implicit-function-declaration]
drivers/regulator/arizona-ldo1.c:193:2: error: implicit declaration of function 'of_parse_phandle' [-Werror=implicit-function-declaration]
drivers/regulator/arizona-ldo1.c:213:2: error: implicit declaration of function 'of_node_put' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code has .enable_reg and .enable_mask settings, but the implementation
for corresponding callbacks are missing. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Robin Gong <b38343@freescale.com>
Acked-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When fixed_uV is set and n_voltage is 1, regulator core will return
rdev->desc->fixed_uV in regulator_get_voltage() and regulator_list_voltage().
Rename ltc3589_standby_regulator_ops to ltc3589_fixed_standby_regulator_ops,
this makes the code clear that the ops is for fixed voltage regulator.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make this driver depend on I2C and select REGMAP_I2C to fix build failure.
Also allows this driver to be built as module.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use regulator_set_voltage_time_sel() instead of open-coded.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TPS658640 has a different set of output voltage for most LDO and
the RTC LDO isn't settable. This chip also report 2 different version
ID, as the datasheet doesn't list the possible values the second ID
has simply been named TPS658640v2.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add the required definitions and macros to allow easily adding fixed
regulators. This required for the TPS658640 that doesn't allow setting
the LDO_RTC output voltage.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Previously, the PFUZE100 would try to allocate gpio0 io0 because
config.ena_gpio defaults to 0, which can be a valid GPIO. To prevent this
from happening, set this parameter to -EINVAL.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SWB regulators have the ability to be turned on and off. Add
enable/disable support for these regulators.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use more compact of_property_read_{bool|u32}() calls instead of the
of_{find|get}_property() calls.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Linear Technology LTC3589, LTC3589-1,
and LTC3589-2 8-output I2C voltage regulator ICs.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the register for ramp delay of buck1 regulator. Buck1 and buck6
share the field (offset 4) in ramp delay register S2MPA01_REG_RAMP2.
The driver used the same register and field for ramp delay of buck3 and
buck1. This lead to updating of ramp delay of buck3 when setting buck1
and actually the ramp delay of buck1 was never set.
Fixes: f187927146 ("regulator: Add support for S2MPA01 regulator")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org>
Use map_voltage_linear_range() if list_voltage_linear_range() is in use and
nothing is set.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The bcm590xx MFD driver now exposes a secondary regmap descriptor
making the registers for regulators on the secondary I2C slave address
available. Add support for GPLDO1-6 and VBUS regulators found within
this register range.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The of_find_node_by_name function will search for a DT node named
"regulators" after the provided np node, but will not ensure that this node
is a child of np.
This might result in retrieving a "regulators" node that is not related to
the axp20x PMIC.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use regulator API rdev_get_id() to access id of regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
S2MPS11 supports enabling/disabling ramp delay only for buck[2346].
Other bucks have ramp delay enabled always.
However the bit shift for enabling buck6 ramp delay in register is equal
to 0. When ramp delay was set for the bucks unsupporting enable/disable
(buck[15789] and buck10), the ramp delay for buck6 was also enabled.
Fixes: b96244fad9 ("regulator: s2mps11: Don't check enable_shift before setting enable ramp rate")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
S2MPA01 supports enabling/disabling ramp delay only for buck[1234].
Other bucks have ramp delay enabled always.
However the bit shift for enabling buck4 ramp delay in register is equal
to 0. When ramp delay was set for the bucks unsupporting enable/disable
(buck[56789] and buck10), the ramp delay for buck4 was also enabled.
Fixes: f7b1a8dc1c ("regulator: s2mpa01: Don't check enable_shift before setting enable ramp rate")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
of.h is presently being included through asm-generic/gpio.h so will not
be included on some architectures, causing implicit declaration errors
for of_get_child_by_name, of_parse_phandle and of_node_put.
This patch adds the direct include that should be there.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch (60e91b5 regulator: tps65090: Allow setting the overcurrent
wait time) introduced a crash on Tegra Dalmore. On Dalmore the device
tree doesn't have an entry for all of the FETs so it leaves tps_pdata
NULL in some cases. Add a check for NULL like the rest of the code
does.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
GPIO 0 is a valid GPIO so allow using it as external control for
S2MPS14 regulators.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
GPIO 0 is a valid GPIO so allow using it as external control for
regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
An issue was discovered with tps65090 where sometimes the FETs
wouldn't actually turn on when requested (they would report
overcurrent). The most problematic FET was the one used for the LCD
backlight on the Samsung ARM Chromebook (FET1). Problems were
especially prevalent when the device was plugged in to AC power (when
the backlight voltage was higher).
Mitigate the problem by adding retries on the enables of the FETs,
which works around the problem fairly effectively.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Javier Martinez Canillas