Fix erroneous SPI Clock divisor calculation. Make sure SPI_BAUD is always
>= 2. Writing a value of 0 or 1 to the SPI_BAUD register disables the
serial clock.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flush or invalidate caches before doing DMA transfer, if needed.
[Mike Frysinger <vapier.adi@gmail.com>: add comment to address the
issue "Full duplex only works for non-DMA transfers".]
Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This controller can be found on the D-Link DNS-323 for instance, where
it is to be configured via static i2c_board_info in the board-specific
mach-orion/dns323-setup.c; this driver supports only the new-style
driver model.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Matthew Palmer <mpalmer@debian.org>
Signed-off-by: Laurie Bradshaw <bradshaw.laurie@googlemail.com>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not critical.
WARNING: drivers/char/esp.o(.text+0x278): Section mismatch in reference from the function show_serial_version() to the variable .init.data:serial_version
The function show_serial_version() references
the variable __initdata serial_version.
This is often because show_serial_version lacks a __initdata
annotation or the annotation of serial_version is wrong.
WARNING: drivers/char/esp.o(.text+0x27d): Section mismatch in reference from the function show_serial_version() to the variable .init.data:serial_name
The function show_serial_version() references
the variable __initdata serial_name.
This is often because show_serial_version lacks a __initdata
annotation or the annotation of serial_name is wrong.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andrew J. Robinson <arobinso@nyx.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (28 commits)
powerpc: Fix oops when loading modules
powerpc: Wire up preadv and pwritev
powerpc/ftrace: Fix printf format warning
powerpc/ftrace: Fix #if that should be #ifdef
powerpc: Fix ptrace compat wrapper for FPU register access
powerpc: Print information about mapping hw irqs to virtual irqs
powerpc: Correct dependency of KEXEC
powerpc: Disable VSX or current process in giveup_fpu/altivec
powerpc/pseries: Enable relay in pseries_defconfig
powerpc/pseries: Fix ibm,client-architecture comment
powerpc/pseries: Scan for all events in rtasd
powerpc/pseries: Add dispatch dispersion statistics
powerpc: Clean up some prom printouts
powerpc: Print progress of ibm,client-architecture method
powerpc: Remove duplicated #include's
powerpc/pmac: Fix internal modem IRQ on Wallstreet PowerBook
powerpc/wdrtas: Update wdrtas_get_interval to use rtas_data_buf
fsl-diu-fb: Pass the proper device for dma mapping routines
powerpc/pq2fads: Update device tree for use with device-tree-aware u-boot.
cpm_uart: Disable CPM udbg when re-initing CPM uart, even if not the console.
...
Asus boards have an ACPI interface for interacting with the hwmon (fan,
temperatures, voltages) subsystem; this driver exposes the relevant
information via the standard sysfs interface.
There are two different ACPI interfaces:
- an old one (based on RVLT/RFAN/RTMP)
- a new one (GGRP/GITM)
Both may be present but there a few cases (my board, sigh) where the
new interface is just an empty stub; the driver defaults to the old one
when both are present.
The old interface has received a considerable testing, but I'm still
awaiting confirmation from my tester that the new one is working as
expected (hence the debug code is still enabled).
Currently all the attributes are read-only, though a (partial) control
should be possible with a bit more work.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The legacy i2c binding model is going away really soon now, so convert
the lm95241 driver to the new binding model or it will break.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>
mount/1865 is trying to release lock (&lo->lo_ctl_mutex) at:
but there are no more locks to release!
mutex is already unlocked in loop_clr_fd(), we should not
try to unlock it in lo_release() again.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
'disable_delay' was static which is wrong as it is calculated using the per-device
bus speed. This patch turns 'disable_delay' into a per-device variable.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Support for the s6000 on-chip i2c controller.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch makes the I2C bus speed configurable by using the I2C node
property "clock-frequency". If the property is not defined, the old
fixed clock settings will be used for backward comptibility.
The generic I2C clock properties, especially the CPU-specific source
clock pre-scaler are defined via the OF match table:
static const struct of_device_id mpc_i2c_of_match[] = {
...
{.compatible = "fsl,mpc8543-i2c",
.data = &(struct fsl_i2c_match_data) {
.setclock = mpc_i2c_setclock_8xxx,
.prescaler = 2,
},
},
The "data" field defines the relevant I2C setclock function and the
relevant pre-scaler for the I2C source clock frequency.
It uses arch-specific tables and functions to determine resonable
Freqency Divider Register (fdr) values for MPC83xx, MPC85xx, MPC86xx,
MPC5200 and MPC5200B.
The i2c->flags field and the corresponding FSL_I2C_DEV_* definitions
have been removed as they are obsolete.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch used the dev_dbg, dev_err, etc. functions for debug
and error output instead of printk and pr_debug.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix errors reported by checkpatch (indention, long lines, trailing
white space, etc.).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
[ben-linux@fluff.org: fix minor patch fault in remove]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This is required in order to ensure that core system devices such as
voltage regulators attached via I2C are avaiable early in boot.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The platform data for the i2c-s3c2410 driver used to allow a min,
max and desired frequency for the I2C bus. This patch reduces it
to simply a desired frequency ceiling and corrects all the uses
of the platform data appropriately.
This means, for example, that on a system with a 66MHz fclk, a
request for 100KHz will achieve 65KHz which is safe and
acceptable, rather than 378KHz which it would have achieved
without this change.
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
[ben-linux@fluff.org: tidy subject and description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The sda_delay field should be specified in ns, not in clock ticks
as when using cpufreq we could be changing the bus rate.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Implementation of I2C Adapter/Algorithm Driver for I2C Bus integrated
in Freescale's i.MX/MXC processors.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This driver supports mflash IO mode for linux.
Mflash is embedded flash drive and mainly targeted mobile and consumer
electronic devices.
Internally, mflash has nand flash and other hardware logics and supports 2
different operation (ATA, IO) modes. ATA mode doesn't need any new driver
and currently works well under standard IDE subsystem. Actually it's one
chip SSD. IO mode is ATA-like custom mode for the host that doesn't have
IDE interface.
Followings are brief descriptions about IO mode.
A. IO mode based on ATA protocol and uses some custom command. (read confirm,
write confirm)
B. IO mode uses SRAM bus interface.
C. IO mode supports 4kB boot area, so host can boot from mflash.
This driver is quitely similar to a standard ATA driver, but because of
following reasons it is currently seperated with ATA layer.
1. ATA layer deals standard ATA protocol. ATA layer have many low-
level device specific interface, but data transfer keeps ATA rule.
But, mflash IO mode doesn't.
2. Even though currently not used in mflash driver code, mflash has
some custom command and modes. (nand fusing, firmware patch, etc) If
this feature supported in linux kernel, ATA layer more altered.
3. Currently PATA platform device driver doesn't support interrupt.
(I'm not sure) But, mflash uses interrupt (polling mode is just for
debug).
4. mflash is somewhat under-develop product. Even though some company
already using mflash their own product, I think more time is needed for
standardization of custom command and mode. That time (maybe October)
I will talk to with ATA people. If they accept integration, I will
integrate.
Signed-off-by: unsik Kim <donari75@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add a method for discovering the first memory BAR. All Smart Array
controllers to date have always had the the memory BAR as the first BAR.
A new controller to be released later this year breaks that model.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The MSA2012 cannot inform the driver of configuration changes since all
management is out of band. This is a departure from any storage we have
supported in the past. We need some way to detect changes on the topology
so we implement this kernel thread. In some instances there's nothing we
can do from the driver (like LUN failure) so just print out a message. In
the case where logical volumes are added or deleted we call
rebuild_lun_table to refresh the driver's view of the world.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We must complete the full request, so store the request count and then set
the ->data_len to the residual count from the hardware.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The (relatively) new pmac_zilog driver doesn't use the pre-munged
IRQ numbers from the macio_dev unlike other macio things, it
directly maps it off the OF device-tree.
It does that because it can be initialized much earlier than the
registration of the macio devices, in order to get a serial
console early.
Unfortunately, that means that it "misses" some fixups done
by the macio layer to work around missing interrupt descriptions
in the device-tree of the Wallstreet machines.
This patch brings the necessary workaround into the pmac_zilog
driver itself to bring it back to working condition.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The buffer passed to the ibm,get-system-parameter RTAS call must be
in the RMA. To ensure we pass an address in the RMA use rtas_data_buf
for the actual RTAS call and then copy the result to value. We can't
just make it static because this can be compiled in as a module.
Also add the WDRTAS_SP_SPI_LEN so we don't litter '4' throughout the
function.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Tested-by: Adrian Reber <adrian@lisas.de>
Acked-by: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
b44: Use kernel DMA addresses for the kernel DMA API
forcedeth: Fix resume from hibernation regression.
xfrm: fix fragmentation on inter family tunnels
ibm_newemac: Fix dangerous struct assumption
gigaset: documentation update
gigaset: in file ops, check for device disconnect before anything else
bas_gigaset: use tasklet_hi_schedule for timing critical tasklets
net/802/fddi.c: add MODULE_LICENSE
smsc911x: remove unused #include <linux/version.h>
axnet_cs: fix phy_id detection for bogus Asix chip.
bnx2: Use request_firmware()
b44: Fix sizes passed to b44_sync_dma_desc_for_{device,cpu}()
socket: use percpu_add() while updating sockets_in_use
virtio_net: Set the mac config only when VIRITO_NET_F_MAC
myri_sbus: use request_firmware
e1000: fix loss of multicast packets
vxge: should include tcp.h
Conflict in firmware/WHENCE (SCSI vs net firmware)
We must not use the device DMA addresses for the kernel DMA API, because
device DMA addresses have an additional offset added for the SSB translation.
Use the original dma_addr_t for the sync operation.
Cc: stable@kernel.org
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset phy state on resume, fixing a regression caused by powering down
the phy on hibernate.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The client_register and client_unregister methods are optional so
there is no point in defining stub ones. Especially when these methods
are likely to be removed soon.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove an unnecessary error check and reorder some code.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Touching the hflip/vflip register while doing the read/modify/write corrupts the image. Just read from the sensor ctrl cache instead and all is good.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The vflip quirk is better checked at probe time as it's only needed once.
Also add an extra reset at init time to resolve a suspend to ram regression.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reading and writing to a register doesn't always work reliably. Add a cache
and ensure that it is deallocated properly upon module disconnect.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Previously all resolution setting was done with precalculated tables.
When the image is vflipped we need to adjust the alignment which would
require another table. Now we can adjust the parameters on the fly instead.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ov9650: Reading the COM1 register corrupts the image.
Decrease the granularity of the exposure and limit its upper range
as setting such high values doesn't have any effect on the image.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Autogain is on by default, properly set the default value in the v4l2 ctrl.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove an unused sd struct member. Remove a redundant define while we're at it.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move over the v4l2 controls to the sensor specific source file.
Remove the now redundant sensor struct member.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By separating the supported for each sensor into a separate vector we can
eliminate the nmodes variable and instead calculate it at runtime.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Previously, all sensors allocated a part of a large ctrl vector.
Define this vector separately for each sensor instead.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a hack preventing a suspend-to-ram/disk regression.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to save energy, put the sensor in soft sleep mode when not active
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch toggles the led seen on many laptops having a m5602 connected
to a Samsung s5k83a sensor.
Signed-off-by: Lukas Karas <lukas.karas@centrum.cz>
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cleans some unnecessary temporary variable usage in the ov9650 start function.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 34aecd2851 was made obsolete
and invalid by commit 40cf65d149.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch contains the unified driver for Legend Silicon LGS8913 and
LGS8GL5. It should replace lgs8gl5.c in media/dvb/frontends in the future.
Signed-off-by: David T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch fixes cleanup procedure in si470x_usb_driver_probe. Add new label
err_video and change order of freeing memory.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes kfree problem on driver removal, fixes streamoff problem
and removes unnecessary videobuf_waiton from free_buffer function.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch removes empty open and release functions in pci and isa radio
drivers, setting them to NULL. V4L module doesn't call for them due to
previous patch.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch allows v4l2_open and v4l2_release functions return 0 if open and
release driver callbacks set to NULL. This will be used in radio
drivers.
--
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support to the SQ-905 driver to pass back to user space the
sensor orientation information obtained from the camera during init.
Modifies gspca and the videodev2.h header to create the necessary
API.
[mchehab@redhat.com: Changed "Output is" to "Frames are" at the comments, as suggested at LMML]
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to panagonov <panagonov@mail.bg> for requesting support and
testing patches.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove support for the debug call VIDIOC_INT_S_AUDIO_ROUTING from cx18
and ivtv. These internal ioctls shouldn't be exposed. These were only
used through the cx18-ctl and ivtv-ctl utilities, and only when testing
a new card variant.
This cleanup allows the removal of this ioctl from v4l2-common.h.
Cc: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is no longer needed to use a struct pointer as argument, since v4l2_subdev
doesn't require that ioctl-like approach anymore. Instead just pass the input,
output and config (new!) arguments directly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The line-in was muted twice instead of the line-in and the cd-in.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With all the v4l2_subdev changes that were made to these drivers it is a
good idea to increase the version number of each driver.
It's just the patch level that is increased, except for the zoran and saa7146
drivers where the minor number was increased due to the more substantial
changes that were made to those two drivers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than duplicating this list everywhere, just put it in tvaudio.h.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The functions v4l2_i2c_new_subdev and v4l2_i2c_new_probed_subdev relied on
i2c_get_adapdata to return the v4l2_device. However, this is not always
possible on embedded platforms. So modify the API to pass the v4l2_device
pointer explicitly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add utility function to probe for a single address, rather than a list
of addresses.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Originally the intention was to switch to the new style i2c API starting with
the introduction of the API in 2.6.22. However, the i2c_new_probed_device()
function has a lethal bug that wasn't fixed until 2.6.25. Or more accurately,
it was only fixed in the stable series of 2.6.25 and 2.6.26.
Given the fact that the new i2c API also changed starting with 2.6.26 (the
addition of i2c_device_id), it is easiest to switch APIs starting with
2.6.26.
This patch updates all the legacy code accordingly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s_std didn't belong in the tuner ops. Stricly speaking it should be part of
the video ops, but it is used by audio and tuner devices as well, so it is
more efficient to make it part of the core ops.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The init callback was used in several places to load firmware. Make a separate
load_fw callback for that. This makes the code a lot more understandable.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s_standby is only used to put the tuner in powersaving mode, so move it
from core to tuner.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that all drivers are converted to v4l2_subdev we can remove legacy code
in v4l2-common. Also move the documentation of the internal API to
v4l2-subdev.h where it really belongs.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2-subdev.c and v4l2-i2c-drv-legacy.h were used to support the old i2c
API. All v4l drivers are now converted to v4l2_subdev, so these two files
can be removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All drivers that use tvaudio now use v4l2_subdev, so we can remove the
legacy code from tvaudio.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All drivers that use the tuner module now use v4l2_subdev, so we can remove the
legacy code from this module.
Note that TUNER_SET_CONFIG is still called by tuner-simple.c, so we have
to handle it via a .command callback. There must be a better way to do this,
but for now this will work.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All drivers that use tvp5150 now use v4l2_subdev, so we can remove the
legacy code from tvp5150.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All drivers that use saa7115 now use v4l2_subdev, so we can remove the
legacy code from saa7115.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All drivers that use msp3400 now use v4l2_subdev, so we can remove the
legacy code from msp3400.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Hennerich