Mediatek MT7620 SoC has syscfg0 bits where it sets the type of memory being used.
However, sometimes those bits are not set properly (reading "11"). In this case, the SoC assumes SDRAM.
The patch below reflects that.
Signed-off-by: Sashka Nochkin <linux-mips@durdom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13135/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The "a" version of the MT7620 has single port PCIE bus. The driver is
straightforward without any special magic required. The driver works on
MT7620 and MT7628. There are a few magic values that get written to the
pcie phy and a register of which we only know the name. I marked these
places as vodoo in the comments above the code.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11996/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralink was acquired by Mediatek. Represent this in the cpuinfo. It
apparently confused people.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11994/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 418d29c870 ("MIPS: ralink: Unify SoC id handling") was not fully
correct. The logic for the SoC check got inverted. We need to check if it
is not a MT76x8.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11992/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MT7621 is based on a 1004k core. This patch adds support for the SoC. The
timer and IRQ is just boiler plate as GIC has recently been moved to
generic places in the kernel and just works.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11990/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some of the newer SoCs use the GIC. This patch splits the INTC out into its
own symbol, allowing us to add the gic code in the following patch.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11989/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"These are the highlists of the main MIPS pull request for 4.4:
- Add latencytop support
- Support appended DTBs
- VDSO support and initially use it for gettimeofday.
- Drop the .MIPS.abiflags and ELF NOTE sections from vmlinux
- Support for the 5KE, an internal test core.
- Switch all MIPS platfroms to libata drivers.
- Improved support, cleanups for ralink and Lantiq platforms.
- Support for the new xilfpga platform.
- A number of DTB improvments for BMIPS.
- Improved support for CM and CPS.
- Minor JZ4740 and BCM47xx enhancements"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (120 commits)
MIPS: idle: add case for CPU_5KE
MIPS: Octeon: Support APPENDED_DTB
MIPS: vmlinux: create a section for appended DTB
MIPS: Clean up compat_siginfo_t
MIPS: Fix PAGE_MASK definition
MIPS: BMIPS: Enable GZIP ramdisk and timed printks
MIPS: Add xilfpga defconfig
MIPS: xilfpga: Add mipsfpga platform code
MIPS: xilfpga: Add xilfpga device tree files.
dt-bindings: MIPS: Document xilfpga bindings and boot style
MIPS: Make MIPS_CMDLINE_DTB default
MIPS: Make the kernel arguments from dtb available
MIPS: Use USE_OF as the guard for appended dtb
MIPS: BCM63XX: Use pr_* instead of printk
MIPS: Loongson: Cleanup CONFIG_LOONGSON_SUSPEND.
MIPS: lantiq: Disable xbar fpi burst mode
MIPS: lantiq: Force the crossbar to big endian
MIPS: lantiq: Initialize the USB core on boot
MIPS: lantiq: Return correct value for fpi clock on ar9
MIPS: ralink: Add missing clock on rt305x
...
Seval of-enabled machines (bmips, lantiq, xlp, pistachio, ralink) copied
the arguments from dtb to arcs_command_line to prevent the kernel from
overwriting them.
Since there is now an option to keep the dtb arguments, default to the
new option remove the "backup" to arcs_command_line in case of USE_OF is
enabled, except for those platforms that still take the bootloader
arguments or do not use any at all.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Ganesan Ramalingam <ganesanr@broadcom.com>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11285/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code currently panics if PCI is enabled but the SoC has no PCI bus.
This check is superfluous as the driver only loads if enabled in the
devicetree.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11444/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MT7688 has several uarts that can be used for console. There are several
boards in the wild, that use ttyS1 or ttyS2. This patch applies a simply
autodetection routine to figure out which ttyS the bootloader used as
console. The uarts come up in 6 bit mode by default. The bootloader will
have set 8 bit mode on the console. Find that 8bit tty and use it.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11459/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If the USB HCD is running and the cpu is scaled too low, then the USB
stops working. Increase the idle speed of the core to fix this if the
kernel is built with USB support.
The "magic" values are taken from the Ralink SDK Kernel.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11441/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Seeing the 'of' characters in a symbol that is being called from
ACPI seems to freak out people. So let's do a bit of pointless
renaming so that these folks do feel at home.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Migrate ralink driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linaro-kernel@lists.linaro.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Patchwork: https://patchwork.linux-mips.org/patch/10610/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull irq fixes from Thomas Gleixner:
"This contains:
- a series of fixes for interrupt drivers to prevent a potential race
when installing a chained interrupt handler
- a fix for cpumask pointer misuse
- a fix for using the wrong interrupt number from struct irq_data
- removal of unused code and outdated comments
- a few new helper functions which allow us to cleanup the interrupt
handling code further in 4.3
I decided against doing the cleanup at the end of this merge window
and rather do the preparatory steps for 4.3, so we can run the final
ABI change at the end of the 4.3 merge window with less risk"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
ARM/LPC32xx: Use irq not hwirq for __irq_set_handler_locked()
genirq: Implement irq_set_handler_locked()/irq_set_chip_handler_name_locked()
genirq: Introduce helper irq_desc_get_irq()
genirq: Remove irq_node()
genirq: Clean up outdated comments related to include/linux/irqdesc.h
mn10300: Fix incorrect use of irq_data->affinity
MIPS/ralink: Fix race in installing chained IRQ handler
MIPS/pci: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
m68k/psc: Fix race in installing chained IRQ handler
avr32/at32ap: Fix race in installing chained IRQ handler
sh/intc: Fix race in installing chained IRQ handler
sh/intc: Fix potential race in installing chained IRQ handler
pinctrl/sun4i: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/exynos: Fix race in installing chained IRQ handler
pinctrl/st: Fix race in installing chained IRQ handler
pinctrl/adi2: Fix race in installing chained IRQ handler
...
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
|
-irq_set_chained_handler(E1, E3);
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
...
|
-irq_set_chained_handler(E1, E3);
...
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Aleksey Makarov <aleksey.makarov@auriga.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86@kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-acpi@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10086/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Due to a typo the illegal access interrupt is never cleared in by
the interupt handler, causing an effective deadlock on the first
illegal access.
This was broken since the code was introduced in 5433acd81e ("MIPS:
ralink: add illegal access driver"), but only exposed when the Kconfig
symbol was added, thus enabling the code.
Cc: <stable@vger.kernel.org> [3.18+]
Fixes: a7b7aad383 ("MIPS: ralink: add missing symbol for RALINK_ILL_ACC")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/10172/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A driver was added in commit 5433acd81e ("MIPS: ralink: add illegal access
driver") without the Kconfig section being added. Fix this by adding the symbol
to the Kconfig file.
Signed-off-by: John Crispin <blogic@openwrt.org>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9299/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
This is the small version of MT7620a.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8030/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the new MT7621/8 SoC and kill ifdefs.
Cleanup some whitespace error while we are at it.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8028/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Before we had a pinctrl driver we used a custom OF api. This patch converts the
soc specific pinmux data to a new set of structs. We also add some new pinmux
setings.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8009/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is a regression caused by:
commit afb46f7996
Author: Rob Herring <robh@kernel.org>
Date: Wed Apr 2 19:07:24 2014 -0500
mips: ralink: convert to use unflatten_and_copy_device_tree
Make the of init code reuse the cmdline defined inside the dts.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8008/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds a trivial driver that allows userland to extract the bootrom of
a SoC via debugfs.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8002/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Register the wireless mac clock on rti3883. This is required by the wifi driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8007/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Register the wireleass mac clock on rt2880. This is required by the wifi driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8006/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This function was missing causing make allmod to fail.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8005/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
RT5350 relies on the bootloader setting up the memc correctly. On some boards
the setup is incorrect leading to 32 MB being available but only 16 MB being
recognized. Allow these boards to manually override the memory range.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8004/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These SoCs have a special irq that fires upon an illegal memmory access.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/8003/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Print the PMU and LDO settings on boot.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/7999/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Álvaro Fernández Rojas