This patch reduces the value for I2C timeout and udelay.
The udelay was reduced to 10 (old: 40) which is still very high as for
standard-mode I2C even 5 should work. This gives a speedup of factor 4
when talking to I2C devices.
The timeout was reduced to 2 (old: 20) which is taken from the radeon
driver so it should work as well. This gives a speedup of factor 10 when
detecting that there is no I2C device we want to talk to.
This causes a huge improvement of device initialization time.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch enables the I2C port to talk with the CRT. This allows adding
EDID reading and parsing capability for CRTs.
Just a small preparation, no notable changes in user experience yet.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: Joseph Chan <JosephChan@via.com.tw>
i2c_transfer returns negative errno on error and number of messages
processed on success. Just returning this value would give a poor
interface as it is not obvious that you must compare with 2 after reading
1 or n bytes and with 1 after writing 1 byte to determine if it was
successful. To avoid this error prone interface convert the error code
of a successful read/write to zero and all other non-negative values to
an negative error code.
This fixes a regression introduced by
via: Rationalize vt1636 detection
which resulted in no longer detecting a VT1636 chip and therefore has
broken the output in configurations which contain this chip.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: stable@kernel.org
This patch merges tbl1636 into vt1636 and cleans it up as the data was
only used there anyway. No runtime changes are expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch moves common parts of dvi.c, lcd.c and vt1636.c to hw.c to
start a per output device power management. There should be no runtime
changes aside that this patch enables the proc interface to enable/disable
devices when needed which greatly increases the chances that changes to
the output device configuration will work. However the power management is
not yet complete so it might fail on some configurations. As this area is
quite complex and touches undocumented things there is a slight chance of
regressions.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch cleans the LCD code up. It forbids overwritting global
decissions like what IGA should be used as the source and whether to
enable the second display channel. Additionally it removes a bit code
duplication.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch extends the proc entry to contain a possibility to view and
change the output devices for each IGA. This is useful for debugging
output problems as it provides a reliable way to query which low level
devices are active after VIAs output device configuration nightmare
happended. It's as well suitable for daily use as one can change the
output configuration on the fly for example to connect a projector.
At the moment it's still unstable. The reason is that we have to handle
a bunch of undocumented output devices (those without a proper name) and
that this patch is the first step to collect and verify the needed
information. Basically the only configuration change that is expected to
work at the moment is switching output devices between IGA1 and IGA2.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Andrew Morton <akpm@linux-foundation.org>
This patch merges the remaining functionality of the output path
function in the associated enabling functions. This is very natural as
most of the remaining code does actually enable the device.
Just some more or less intelligent code merge. If no stupid mistakes
occured there should be no regressions.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch uses the iga{1,2}_devices variables to select which IGA
should be the source. Doing this is convinient, more powerfull
than the older scheme and easy extendable to support further output
devices. It is not yet completed as the device on/off selection needs
to be converted to the same scheme to take full advantage.
No visible changes yet as we want to complete the transition before
anouncing any unstabke interface.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch adds a new output device management that stores for each
IGA which output devices are routed to it and a compatiblity layer
that converts the old per-output device values in the new format.
Bounding the output devices to each IGA is a central idea of the
cleanup. Doing it this way should be easier and make much more sense
than the old format which happily mixed different output devices
together and did not even take into account that some devices are no
longer available on newer chipsets.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
The result of viafb_set_iga_path can change after init only in the
hotplug ioctl. So we can move it there rather than doing it always
when a new mode is set. The setup during init is done via a call
from the init chip funtion.
This change enables a stable mapping between the old device scheme
and a new more powerfull one.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
There are a lot of init functions which are not marked as such.
Fix this.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch rips the device routing out of the 3 main functions to
separate functions to make them available for transition to a better
controlling scheme.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Move the enabling of the second display channel to the generic
output routing function and do it exactly if something is using it.
This unifies a zoo of variants how to do it and does no longer
disable it if LCD is not on the second display which is much saner
as there can be other users who need it. Probably this did not cause
any problems so far as we only recently started dual fb support and
otherwise there won't be other users and LCD is preferred assigned to
second display channel.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Move all output path routing directly in the viafb_setmode. This
gives a better overview and allows to factor similar parts out.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch moves the power on/off sequences to lcd.c as they are only
used there. This allows removing lcdtbl.h as the other stuff is not
used.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Looks like we did reset the PLL of the (whatever) engine instead of
the PLL of the secondary display (IGA2, LCDCK). This patch fixes it.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
The VIAFB_GET_INFO device ioctl allows unprivileged users to read 246
bytes of uninitialized stack memory, because the "reserved" member of
the viafb_ioctl_info struct declared on the stack is not altered or
zeroed before being copied back to the user. This patch takes care of
it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
drivers/video/via/via-gpio.c: In function 'viafb_gpio_probe':
drivers/video/via/via-gpio.c:216: warning: assignment from incompatible pointer type
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
VIA UniChrome and Chrome9 GPUs only exist as Integrated Graphics
Processors in x86 chipsets.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch moves two functions from .devexit to .text,
which are called on the probe error path.
Also a function which is called by probe is moved
from .text to .devinit.
WARNING: vmlinux.o(.devinit.text+0x2ca5): Section mismatch in reference
from the function via_pci_probe() to the function
devexit.text:via_teardown_subdevs()
The function __devinit via_pci_probe() references
a function __devexit via_teardown_subdevs().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
via_teardown_subdevs() so it may be used outside an exit section.
WARNING: vmlinux.o(.devinit.text+0x2cb1): Section mismatch in reference
from the function via_pci_probe() to the function
devexit.text:via_pci_teardown_mmio()
The function __devinit via_pci_probe() references
a function __devexit via_pci_teardown_mmio().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
via_pci_teardown_mmio() so it may be used outside an exit section.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
viafb: fix accel_flags check_var bug
In check_var we should check and modify the var given and not the
one which is currently active. So this code was obviously wrong.
Probably this was doing no harm because all acceleration functions
also check whether acceleration is possible. (otherwise I would
expect this to lead to a null pointer dereference)
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: probe cleanups
Removal of strange special cases that must not exist as well as a
useless check.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: remove ioctls which break the framebuffer interface
The ioctls VIAFB_SET_DEVICE, VIAFB_SET_DEVICE_INFO and
VIAFB_SET_SECOND_MODE are removed because they prevent a clean
framebuffer driver because they modify the hardware and/or the
internal structures.
There are no known applications using these ioctls so no breakage is
expected. Additionaly the main functionality was duplicating the
framebuffer interface so there really should not exist any user.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: update fix before calculating depth
As the depth calculation depends on information in fix it is saner to
do the update first.
No runtime change expected as the value visual in fix used never
changes to MONO.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: PLL value cleanup
This is a big change of how PLL values are handled on the road to
dynamic PLL value generation. The table was converted automatically in
the relevant parameters for frequency generation. Sadly there were some
bits set whose meaning is unknown. Those differences are documented
but ignored as the unichrome code implies that they are not important
(a big thanks to Luc for his amazing work).
The PLL values for 31490000 and 133308000 are deleted as they were more
than 5% off and not used anyway. The values for CX700@60466000 and
VX855@153920000 are corrected as they were wrong and easily correctable
as enough correct values was available because CX700 and VX855 support
the same values only with a little difference in hardware format.
All remaining values are not more than 2% off.
Additionally the surrounding code is changed as needed especially the
byte order of the values written to hardware to allow nicer conversion
functions.
This is mostly a change preparing for dynamic PLL generation and the two
corrected values aside no runtime change is expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: simplify lcd size "detection"
Remove all occurences of get_lcd_size_method as only the values
GET_LCD_SIZE_BY_VGA_BIOS and GET_LCD_SIZE_BY_USER_SETTING were used
which had the identical code so there is no need to make things look
more complicated than they actually are.
Just a bit of of cleanup, really no regressions expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: fix PCI table
This patch fixes an oddity in the device table where the P4M890 ID was
assigned with the enumeration value of CN700 which itself was missing.
This is a regression introduced by
"viafb: make viafb a first-class citizen using pci_driver"
While at it reorder the table to reflect the order of the enumeration
values.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Harald Welte <laforge@gnumonks.org>
viafb: add lcd scaling support for some IGPs
These IGPs should also support lcd scaling but likely this switch was
missed when adding support for them. Fix it, allowing lcd scaling on
CN750, VX800 and VX855. At least this improves the situation for
VX855. (there seems to be another scaling unrelated bug somewhere)
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: improve lcd code readability
This changes the code to better reflect that we can (currently) only
perform upscaling.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
viafb: remove duplicated scaling code
The code for P4M900 does the same as for all newer IGPs so there is no
reason to duplicate it. Just reducing the code to maintain.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Pointed out by Lucas who found the new one in a comment in
setup_percpu.c. And then I fixed the others that I grepped
for.
Reported-by: Lucas <canolucas@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a nuc900 lcd build error.
Since the 'nuc900_driver_clksrc_div()' API cannot be merged into mainline
successfully, I removed this clock source selection hook in this driver.
This means nuc900 lcd driver has to select default clock source from the
external crystal now.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Qiang Wang <rurality.wq@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: vmlinux.o(.data+0x196e8): Section mismatch in reference from the
variable lxfb_driver to the function .init.text:lxfb_probe() The variable
lxfb_driver references the function __init lxfb_probe()
This changes lxfb_probe and friends to use __devinit, and also adds
__devexit to lxfb_remove.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: vmlinux.o(.data+0x195d8): Section mismatch in reference from the
variable gxfb_driver to the function .init.text:gxfb_probe() The variable
gxfb_driver references the function __init gxfb_probe()
This changes gxfb_probe and friends to use __devinit, and also adds
__devexit to gxfb_remove.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code in rfbi.c tried to get the omapdss platform_device via a static
member defined in dispc.c, leading to a compile error. The same
platform_device is available through rfbi-struct.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
I was observing the following error messages on my OMAP1 based Amstrad Delta
board when first changing from text to graphics mode or vice versa after the
LCD display had been blanked:
omapfb omapfb: timeout waiting for FRAME DONE
with a followup error message while unblanking it back:
omapfb omapfb: resetting (status 0xffffffb2,reset count 1)
As a visible result, image pixels happened to be shifted by a few bits,
giving wrong colors.
Examining the code, I found that this problem occures when an OMAP1 internal
LCD controller is disabled from omap_lcdc_suspend() and then a subsequent
omap_lcdc_setup_plane() calls disable_controller() again. This potentially
error provoking behaviour is triggered by the lcdc.update_mode flag being kept
at OMAP_AUTO_UPDATE, regardless of the controller and panel being suspended.
This patch tries to correct the problem by replacing both omap_lcdc_suspend()
and omap_lcdc_resume() function bodies with single calls to
omap_lcdc_set_update_mode() with a respective OMAP_UPDATE_DISABLE or
OMAP_AUTO_UPDATE argument. As a result, exactly the same lower level
operations are performed, with addition of changing the lcdc.update_mode flag
to a value better suited for the controller state. This prevents any further
calls to disable_controller() from omap_lcdc_setup_plane() while the display
is suspended.
Created against linux-2.6.34-rc7.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: Make intc messages consistent via pr_fmt.
sh: make sure static declaration on ms7724se
sh: make sure static declaration on mach-migor
sh: make sure static declaration on mach-ecovec24
sh: make sure static declaration on mach-ap325rxa
clocksource: sh_cmt: compute mult and shift before registration
clocksource: sh_tmu: compute mult and shift before registration
sh: PIO disabling for x3proto and urquell.
sh: mach-sdk7786: conditionally disable PIO support.
sh: support for platforms without PIO.
usb: r8a66597-hcd pio to mmio accessor conversion.
usb: gadget: r8a66597-udc pio to mmio accessor conversion.
usb: gadget: m66592-udc pio to mmio accessor conversion.
sh: add romImage MMCIF boot for sh7724 and Ecovec V2
sh: add boot code to MMCIF driver header
sh: prepare MMCIF driver header file
sh: allow romImage data between head.S and the zero page
sh: Add support MMCIF for ecovec
sh: remove duplicated #include
input: serio: disable i8042 for non-cayman sh platforms.
...
Commit f601441916 ("imxfb: add support for
i.MX25:) has inserted the symbol HAVE_FB_IMX, which does not depend on FB
after the menuconfig FB. This breaks the menu, presenting most of the
drivers outside of it, when using menuconfig.
Moving the symbol to the start of the file, just like HAVE_FB_ATMEL, fixes
the problem without breaking it for iMX25 configurations (tested with
ARCH=arm, no build).
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed by Nick Piggin, ->page_mkwrite provides a way to keep a page
locked until the associated PTE is marked dirty.
Re-implement the fix by using this mechanism.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 49bbd815fd ("fb_defio:
fix for non-dirty ptes").
Although the fix provided is correct, it's been suggested to avoid the
underlying race in the same way as it is currently done in filesystems
like NFS, for maintainability.
A following patch "fb_defio: redo fix for non-dirty ptes" will provide
such an alternate fix.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Cc: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I2C drivers can use the clientdata-pointer to point to private data. As I2C
devices are not really unregistered, but merely detached from their driver, it
used to be the drivers obligation to clear this pointer during remove() or a
failed probe(). As a couple of drivers forgot to do this, it was agreed that it
was cleaner if the i2c-core does this clearance when appropriate, as there is
no guarantee for the lifetime of the clientdata-pointer after remove() anyhow.
This feature was added to the core with commit
e4a7b9b04d to fix the faulty drivers.
As there is no need anymore to clear the clientdata-pointer, remove all current
occurrences in the drivers to simplify the code and prevent confusion.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fixes build errors in a number of framebuffer drivers caused
by the OF device_node pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use the same color-calculating algorithm as in atyfb_imageblit in this
driver or in generic cfb_fillrect.
This patch fixes bad colors when using an accelerator in 15-bit and
16-bit modes.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Florian Tobias Schandinat