There is no functional change in this patch, it only prepares the next one.
rt6_nexthop() will be used by ip6_dst_lookup_neigh(), which uses const
variables.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: kbuild test robot <lkp@intel.com>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace gpiod_set_value() with gpiod_set_value_cansleep(), as the switch
reset GPIO can be connected to e.g. I2C GPIO expander and it is perfectly
fine for the kernel to sleep for a bit in ksz_switch_register().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In configuration of vlan over bridge over aquantia device
it was found that vlan tagged traffic is dropped on chip.
The reason is that bridge device enables promisc mode,
but in atlantic chip vlan filters will still apply.
So we have to corellate promisc settings with vlan configuration.
The solution is to track in a separate state variable the
need of vlan forced promisc. And also consider generic
promisc configuration when doing vlan filter config.
Fixes: 7975d2aff5 ("net: aquantia: add support of rx-vlan-filter offload")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should rather have vlan_tci filled all the way down
to the transmitting netdevice and let it do the hw/sw
vlan implementation.
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We build vlan on top of bonding interface, which vlan offload
is off, bond mode is 802.3ad (LACP) and xmit_hash_policy is
BOND_XMIT_POLICY_ENCAP34.
Because vlan tx offload is off, vlan tci is cleared and skb push
the vlan header in validate_xmit_vlan() while sending from vlan
devices. Then in bond_xmit_hash, __skb_flow_dissect() fails to
get information from protocol headers encapsulated within vlan,
because 'nhoff' is points to IP header, so bond hashing is based
on layer 2 info, which fails to distribute packets across slaves.
This patch always enable bonding's vlan tx offload, pass the vlan
packets to the slave devices with vlan tci, let them to handle
vlan implementation.
Fixes: 278339a42a ("bonding: propogate vlan_features to bonding master")
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The syzbot reported
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xca/0x13e lib/dump_stack.c:113
print_address_description+0x67/0x231 mm/kasan/report.c:188
__kasan_report.cold+0x1a/0x32 mm/kasan/report.c:317
kasan_report+0xe/0x20 mm/kasan/common.c:614
qmi_wwan_probe+0x342/0x360 drivers/net/usb/qmi_wwan.c:1417
usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
Caused by too many confusing indirections and casts.
id->driver_info is a pointer stored in a long. We want the
pointer here, not the address of it.
Thanks-to: Hillf Danton <hdanton@sina.com>
Reported-by: syzbot+b68605d7fadd21510de1@syzkaller.appspotmail.com
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Fixes: e4bf63482c ("qmi_wwan: Add quirk for Quectel dynamic config")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the MAC address setup in the probe. The MAC address
retrieved using of_get_mac_address was checked for not containing an
error, but it may also be NULL which wasn't tested. Fix it by replacing
IS_ERR with IS_ERR_OR_NULL.
Fixes: 541ddc66d6 ("net: macb: support of_get_mac_address new ERR_PTR error")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 605ad7f184 "tcp: refine TSO autosizing",
outbound throughput is dramatically reduced for some connections, as sis900
is doing TX completion within idle states only.
Make TX completion happen after every transmitted packet.
Test:
netperf
before patch:
> netperf -H remote -l -2000000 -- -s 1000000
MIGRATED TCP STREAM TEST from 0.0.0.0 () port 0 AF_INET to 95.223.112.76 () port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 327680 327680 253.44 0.06
after patch:
> netperf -H remote -l -10000000 -- -s 1000000
MIGRATED TCP STREAM TEST from 0.0.0.0 () port 0 AF_INET to 95.223.112.76 () port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 327680 327680 5.38 14.89
Thx to Dave Miller and Eric Dumazet for helpful hints
Signed-off-by: Sergej Benilov <sergej.benilov@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When transmitting certain PTP frames, e.g. SYNC and DELAY_REQ, the
PTP daemon, e.g. ptp4l, is polling the driver for the frame transmit
hardware timestamp. The polling will most likely timeout if the tx
coalesce is enabled due to the Interrupt-on-Completion (IC) bit is
not set in tx descriptor for those frames.
This patch will ignore the tx coalesce parameter and set the IC bit
when transmitting PTP frames which need to report out the frame
transmit hardware timestamp to user space.
Fixes: f748be531d ("net: stmmac: Rework coalesce timer and fix multi-queue races")
Signed-off-by: Roland Hii <roland.king.guan.hii@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ADDSUB bit is set, the system time seconds field is calculated as
the complement of the seconds part of the update value.
For example, if 3.000000001 seconds need to be subtracted from the
system time, this field is calculated as
2^32 - 3 = 4294967296 - 3 = 0x100000000 - 3 = 0xFFFFFFFD
Previously, the 0x100000000 is mistakenly written as 100000000.
This is further simplified from
sec = (0x100000000ULL - sec);
to
sec = -sec;
Fixes: ba1ffd74df ("stmmac: fix PTP support for GMAC4")
Signed-off-by: Roland Hii <roland.king.guan.hii@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arc4 crypto is mandatory at ppp_mppe probe time, so let's put a
softdep line, so that the corresponding module gets prepared
gracefully. Without this, a simple inclusion to initrd via dracut
failed due to the missing dependency, for example.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain cards in conjunction with certain switches need a little more
time for link setup that results in ethtool link test failure after
offline test. Patch adds a loop that waits for a link setup finish.
Changes in v2:
- added fixes header
Fixes: 4276e47e2d ("be2net: Add link test to list of ethtool self tests.")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix leak of unqueued fragments in ipv6 nf_defrag, from Guillaume
Nault.
2) Don't access the DDM interface unless the transceiver implements it
in bnx2x, from Mauro S. M. Rodrigues.
3) Don't double fetch 'len' from userspace in sock_getsockopt(), from
JingYi Hou.
4) Sign extension overflow in lio_core, from Colin Ian King.
5) Various netem bug fixes wrt. corrupted packets from Jakub Kicinski.
6) Fix epollout hang in hvsock, from Sunil Muthuswamy.
7) Fix regression in default fib6_type, from David Ahern.
8) Handle memory limits in tcp_fragment more appropriately, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (24 commits)
tcp: refine memory limit test in tcp_fragment()
inet: clear num_timeout reqsk_alloc()
net: mvpp2: debugfs: Add pmap to fs dump
ipv6: Default fib6_type to RTN_UNICAST when not set
net: hns3: Fix inconsistent indenting
net/af_iucv: always register net_device notifier
net/af_iucv: build proper skbs for HiperTransport
net/af_iucv: remove GFP_DMA restriction for HiperTransport
net: dsa: mv88e6xxx: fix shift of FID bits in mv88e6185_g1_vtu_loadpurge()
hvsock: fix epollout hang from race condition
net/udp_gso: Allow TX timestamp with UDP GSO
net: netem: fix use after free and double free with packet corruption
net: netem: fix backlog accounting for corrupted GSO frames
net: lio_core: fix potential sign-extension overflow on large shift
tipc: pass tunnel dev as NULL to udp_tunnel(6)_xmit_skb
ip6_tunnel: allow not to count pkts on tstats by passing dev as NULL
ip_tunnel: allow not to count pkts on tstats by setting skb's dev to NULL
tun: wake up waitqueues after IFF_UP is set
net: remove duplicate fetch in sock_getsockopt
tipc: fix issues with early FAILOVER_MSG from peer
...
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
- Make switch to eMMC HS400 more robust for some controllers
- Add two SDIO func API to manage re-tuning constraints
- Prevent processing SDIO IRQs when the card is suspended
MMC host:
- sdhi: Disallow broken HS400 for M3-W ES1.2, RZ/G2M and V3H
- mtk-sd: Fixup support for SDIO IRQs
- sdhci-pci-o2micro: Fixup support for tuning
Wireless BRCMFMAC (SDIO):
- Deal with expected transmission errors related to the idle states
(handled by the Always-On-Subsystem or AOS) on the SDIO-based WiFi on
rk3288-veyron-minnie, rk3288-veyron-speedy and rk3288-veyron-mickey.
-----BEGIN PGP SIGNATURE-----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=IkL6
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"Here's quite a few MMC fixes intended for v5.2-rc6. This time it also
contains fixes for a WiFi driver, which device is attached to the SDIO
interface. Patches for the WiFi driver have been acked by the
corresponding maintainers.
Summary:
MMC core:
- Make switch to eMMC HS400 more robust for some controllers
- Add two SDIO func API to manage re-tuning constraints
- Prevent processing SDIO IRQs when the card is suspended
MMC host:
- sdhi: Disallow broken HS400 for M3-W ES1.2, RZ/G2M and V3H
- mtk-sd: Fixup support for SDIO IRQs
- sdhci-pci-o2micro: Fixup support for tuning
Wireless BRCMFMAC (SDIO):
- Deal with expected transmission errors related to the idle states
(handled by the Always-On-Subsystem or AOS) on the SDIO-based WiFi
on rk3288-veyron-minnie, rk3288-veyron-speedy and
rk3288-veyron-mickey"
* tag 'mmc-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: Prevent processing SDIO IRQs when the card is suspended
mmc: sdhci: sdhci-pci-o2micro: Correctly set bus width when tuning
brcmfmac: sdio: Don't tune while the card is off
mmc: core: Add sdio_retune_hold_now() and sdio_retune_release()
brcmfmac: sdio: Disable auto-tuning around commands expected to fail
mmc: core: API to temporarily disable retuning for SDIO CRC errors
Revert "brcmfmac: disable command decode in sdio_aos"
mmc: mediatek: fix SDIO IRQ detection issue
mmc: mediatek: fix SDIO IRQ interrupt handle flow
mmc: core: complete HS400 before checking status
mmc: sdhi: disallow HS400 for M3-W ES1.2, RZ/G2M, and V3H
There was an unused variable 'mvpp2_dbgfs_prs_pmap_fops'
Added a usage consistent with other fops to dump pmap
to userspace.
Cc: clang-built-linux@googlegroups.com
Link: https://github.com/ClangBuiltLinux/linux/issues/529
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa the full gnu general public license is included in this
distribution in the file called license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 8 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081207.801261482@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation see readme and copying for
more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081207.060259192@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the version 2 of the gnu general public
license as published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 10 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.259525894@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 53 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.904365654@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment is correct, but the code ends up moving the bits four
places too far, into the VTUOp field.
Fixes: 11ea809f1a (net: dsa: mv88e6xxx: support 256 databases)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Left shifting the signed int value 1 by 31 bits has undefined behaviour
and the shift amount oq_no can be as much as 63. Fix this by using
BIT_ULL(oq_no) instead.
Addresses-Coverity: ("Bad shift operation")
Fixes: f21fb3ed36 ("Add support of Cavium Liquidio ethernet adapters")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently after setting tap0 link up, the tun code wakes tx/rx waited
queues up in tun_net_open() when .ndo_open() is called, however the
IFF_UP flag has not been set yet. If there's already a wait queue, it
would fail to transmit when checking the IFF_UP flag in tun_sendmsg().
Then the saving vhost_poll_start() will add the wq into wqh until it
is waken up again. Although this works when IFF_UP flag has been set
when tun_chr_poll detects; this is not true if IFF_UP flag has not
been set at that time. Sadly the latter case is a fatal error, as
the wq will never be waken up in future unless later manually
setting link up on purpose.
Fix this by moving the wakeup process into the NETDEV_UP event
notifying process, this makes sure IFF_UP has been set before all
waited queues been waken up.
Signed-off-by: Fei Li <lifei.shirley@bytedance.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some transceivers may comply with SFF-8472 even though they do not
implement the Digital Diagnostic Monitoring (DDM) interface described in
the spec. The existence of such area is specified by the 6th bit of byte
92, set to 1 if implemented.
Currently, without checking this bit, bnx2x fails trying to read sfp
module's EEPROM with the follow message:
ethtool -m enP5p1s0f1
Cannot get Module EEPROM data: Input/output error
Because it fails to read the additional 256 bytes in which it is assumed
to exist the DDM data.
This issue was noticed using a Mellanox Passive DAC PN 01FT738. The EEPROM
data was confirmed by Mellanox as correct and similar to other Passive
DACs from other manufacturers.
Signed-off-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Broadcom SDIO cards are idled they go to sleep and a whole
separate subsystem takes over their SDIO communication. This is the
Always-On-Subsystem (AOS) and it can't handle tuning requests.
Specifically, as tested on rk3288-veyron-minnie (which reports having
BCM4354/1 in dmesg), if I force a retune in brcmf_sdio_kso_control()
when "on = 1" (aka we're transition from sleep to wake) by whacking:
bus->sdiodev->func1->card->host->need_retune = 1
...then I can often see tuning fail. In this case dw_mmc reports "All
phases bad!"). Note that I don't get 100% failure, presumably because
sometimes the card itself has already transitioned away from the AOS
itself by the time we try to wake it up. If I force retuning when "on
= 0" (AKA force retuning right before sending the command to go to
sleep) then retuning is always OK.
NOTE: we need _both_ this patch and the patch to avoid triggering
tuning due to CRC errors in the sleep/wake transition, AKA ("brcmfmac:
sdio: Disable auto-tuning around commands expected to fail"). Though
both patches handle issues with Broadcom's AOS, the problems are
distinct:
1. We want to defer (but not ignore) asynchronous (like
timer-requested) tuning requests till the card is awake. However,
we want to ignore CRC errors during the transition, we don't want
to queue deferred tuning request.
2. You could imagine that the AOS could implement retuning but we
could still get errors while transitioning in and out of the AOS.
Similarly you could imagine a seamless transition into and out of
the AOS (with no CRC errors) even if the AOS couldn't handle
tuning.
ALSO NOTE: presumably there is never a desperate need to retune in
order to wake up the card, since doing so is impossible. Luckily the
only way the card can get into sleep state is if we had a good enough
tuning to send it the command to put it into sleep, so presumably that
"good enough" tuning is enough to wake us up, at least with a few
retries.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are certain cases, notably when transitioning between sleep and
active state, when Broadcom SDIO WiFi cards will produce errors on the
SDIO bus. This is evident from the source code where you can see that
we try commands in a loop until we either get success or we've tried
too many times. The comment in the code reinforces this by saying
"just one write attempt may fail"
Unfortunately these failures sometimes end up causing an "-EILSEQ"
back to the core which triggers a retuning of the SDIO card and that
blocks all traffic to the card until it's done.
Let's disable retuning around the commands we expect might fail.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 29f6589140.
After that patch landed I find that my kernel log on
rk3288-veyron-minnie and rk3288-veyron-speedy is filled with:
brcmfmac: brcmf_sdio_bus_sleep: error while changing bus sleep state -110
This seems to happen every time the Broadcom WiFi transitions out of
sleep mode. Reverting the commit fixes the problem for me, so that's
what this patch does.
Note that, in general, the justification in the original commit seemed
a little weak. It looked like someone was testing on a SD card
controller that would sometimes die if there were CRC errors on the
bus. This used to happen back in early days of dw_mmc (the controller
on my boards), but we fixed it. Disabling a feature on all boards
just because one SD card controller is broken seems bad.
Fixes: 29f6589140 ("brcmfmac: disable command decode in sdio_aos")
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Double Lo <double.lo@cypress.com>
Cc: Madhan Mohan R <madhanmohan.r@cypress.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
Number of Rx queues used for flow hashing returned by the driver is
incorrect and this bug prevents user to use the last Rx queue in
indirection table.
Let's say we have a NIC with 6 combined queues:
[root@sm-03 ~]# ethtool -l enp4s0f0
Channel parameters for enp4s0f0:
Pre-set maximums:
RX: 5
TX: 5
Other: 0
Combined: 6
Current hardware settings:
RX: 0
TX: 0
Other: 0
Combined: 6
Default indirection table maps all (6) queues equally but the driver
reports only 5 rings available.
[root@sm-03 ~]# ethtool -x enp4s0f0
RX flow hash indirection table for enp4s0f0 with 5 RX ring(s):
0: 0 1 2 3 4 5 0 1
8: 2 3 4 5 0 1 2 3
16: 4 5 0 1 2 3 4 5
24: 0 1 2 3 4 5 0 1
...
Now change indirection table somehow:
[root@sm-03 ~]# ethtool -X enp4s0f0 weight 1 1
[root@sm-03 ~]# ethtool -x enp4s0f0
RX flow hash indirection table for enp4s0f0 with 6 RX ring(s):
0: 0 0 0 0 0 0 0 0
...
64: 1 1 1 1 1 1 1 1
...
Now it is not possible to change mapping back to equal (default) state:
[root@sm-03 ~]# ethtool -X enp4s0f0 equal 6
Cannot set RX flow hash configuration: Invalid argument
Fixes: 594ad54a2c ("be2net: Add support for setting and getting rx flow hash options")
Reported-by: Tianhao <tizhao@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ef7bfa8472.
Russell King espressed some strong opposition to this
change, explaining that this is trying to make phylink
behave outside of how it has been designed.
Signed-off-by: David S. Miller <davem@davemloft.net>
We get this regression when using RTL8366RB as part of a bridge
with OpenWrt:
WARNING: CPU: 0 PID: 1347 at net/switchdev/switchdev.c:291
switchdev_port_attr_set_now+0x80/0xa4
lan0: Commit of attribute (id=7) failed.
(...)
realtek-smi switch lan0: failed to initialize vlan filtering on this port
This is because it is trying to disable VLAN filtering
on VLAN0, as we have forgot to add 1 to the port number
to get the right VLAN in rtl8366_vlan_filtering(): when
we initialize the VLAN we associate VLAN1 with port 0,
VLAN2 with port 1 etc, so we need to add 1 to the port
offset.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_state field of phylink should carry only valid information
especially when this can be passed to the .mac_config callback.
Update the an_enabled field with the autoneg state in the
phylink_phy_change function.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For better consistency of synthetic NIC names, we set the probe mode to
PROBE_FORCE_SYNCHRONOUS. So the names can be aligned with the vmbus
channel offer sequence.
Fixes: af0a5646cb ("use the new async probing feature for the hyperv drivers")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with CONFIG_NET_DSA_REALTEK_SMI and CONFIG_REALTEK_PHY
enabled as loadable modules, we see the following warning:
warning: same module names found:
drivers/net/phy/realtek.ko
drivers/net/dsa/realtek.ko
Rework so the driver name is realtek-smi instead of realtek.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If some of the switch ports were not listed in the device tree, due to
being unused, the ksz_mib_read_work function ended up accessing a NULL
dp->slave pointer and causing an oops. Skip checking statistics for any
unused ports.
Fixes: 7c6ff470aa ("net: dsa: microchip: add MIB counter reading support")
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Permit mux_id values up to 254 to be used in qmimux_register_device()
for compatibility with ip(8) and the rmnet driver.
Fixes: c6adf77953 ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch qmimux_unregister_device() and qmi_wwan_disconnect() to
use unregister_netdevice_queue() and unregister_netdevice_many()
instead of unregister_netdevice(). This avoids RCU stalls which
have been observed on device disconnect in certain setups otherwise.
Fixes: c6adf77953 ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QMAP code in the qmi_wwan driver is based on the CodeAurora GobiNet
driver which does not process QMAP padding in the RX path correctly.
Add support for QMAP padding to qmimux_rx_fixup() according to the
description of the rmnet driver.
Fixes: c6adf77953 ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* a few memory leaks
* fixes for management frame protection security
and A2/A3 confusion (affecting TDLS as well)
* build fix for certificates
* etc.
-----BEGIN PGP SIGNATURE-----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=AHi5
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-06-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes, all over:
* a few memory leaks
* fixes for management frame protection security
and A2/A3 confusion (affecting TDLS as well)
* build fix for certificates
* etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing all VID filters, the mvpp2_prs_vid_entry_remove would be
called with the TCAM id incorrectly used as a VID, causing the wrong
TCAM entries to be invalidated.
Fix this by directly invalidating entries in the VID range.
Fixes: 56beda3db6 ("net: mvpp2: Add hardware offloading for VLAN filtering")
Suggested-by: Yuri Chipchev <yuric@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VID filtering is implemented in the Header Parser, with one range of 11
vids being assigned for each no-loopback port.
Make sure we use the per-port range when looking for existing entries in
the Parser.
Since we used a global range instead of a per-port one, this causes VIDs
to be removed from the whitelist from all ports of the same PPv2
instance.
Fixes: 56beda3db6 ("net: mvpp2: Add hardware offloading for VLAN filtering")
Suggested-by: Yuri Chipchev <yuric@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PVID is removed from a bridge port, the Linux bridge drops both
untagged and prio-tagged packets. Align mlxsw with this behavior.
Fixes: 148f472da5 ("mlxsw: reg: Add the Switch Port Acceptable Frame Types register")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to an issue on Spectrum-2, in front-panel ports split four ways, 2 out
of 32 port buffers cannot be used. To work around this, the next FW release
will mark them as unused, and will report correspondingly lower total
shared buffer size. mlxsw will pick up the new value through a query to
cap_total_buffer_size resource. However the initial size for shared buffer
pool 0 is hard-coded and therefore needs to be updated.
Thus reduce the pool size by 2.7 MiB (which corresponds to 2/32 of the
total size of 42 MiB), and round down to the whole number of cells.
Fixes: fe099bf682 ("mlxsw: spectrum_buffers: Add Spectrum-2 shared buffer configuration")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TOS value was not extracted correctly. Fix it.
Fixes: 87996f91f7 ("mlxsw: spectrum_flower: Add support for ip tos")
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver tries to periodically refresh neighbours that are used to
reach nexthops. This is done by periodically calling neigh_event_send().
However, if the neighbour becomes dead, there is nothing we can do to
return it to a connected state and the above function call is basically
a NOP.
This results in the nexthop never being written to the device's
adjacency table and therefore never used to forward packets.
Fix this by dropping our reference from the dead neighbour and
associating the nexthop with a new neigbhour which we will try to
refresh.
Fixes: a7ff87acd9 ("mlxsw: spectrum_router: Implement next-hop routing")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same hash function and seed are used for both ECMP and LAG hash.
Therefore, when a LAG device is used as a nexthop device as part of an
ECMP group, hash polarization can occur and all the traffic will be
hashed to a single LAG slave.
Fix this by using a different seed for the LAG hash.
Fixes: fa73989f26 ("mlxsw: spectrum: Use a stable ECMP/LAG seed")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel