Peter Jones uncovered this one while we were debugging the framebuffer
issues. There are some references to -1 in the mxcc asm code, which
should be 0xffffffff.
This patch gets rid of the -1s.
Signed-off-by: Tom 'spot' Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sparc32 ksyms is missing a few more symbols, these are primarily
related to SMP, and will be needed as SMP gets beaten back into
functionality.
Specifically, add __cpu_data (PER_CPU), cpu_online_map, and
phys_cpu_present_map.
This patch assumes that the earlier "linux-2.6.11-sparc-fixksyms.patch"
is applied, otherwise, it will apply with fuzz.
Signed-off-by: Tom 'spot' Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables the sun linux logo to be selected on sparc32.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some missing sparc32 ksyms that are needed.
Specifically, ___rw_read_enter, ___rw_read_exit, ___rw_write_enter, and
sys_close.
Signed-off-by: Tom 'spot' Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the same logic as the other framebuffer fixes committed in 2.6.11,
this is a set of fixes to make TCX functional on the console again. Adds
the tcx_pan_display function, sets the
all->info.var.{red,green,blue}.length values to 8, and runs fb_set_cmap.
Also looks for the correct SUNW,tcx prom value.
This patch just slipped through the cracks.
Originally by: Georg Chini <georg.chini@triaton-webhosting.com>
Signed-off-by: Tom 'spot' Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is incredibly trivial, but it does resolve some of the user
confusion as to what "L1-A" actually is.
Clarify printk message to refer to Stop-A (L1-A).
Gentoo has a virtually identical patch in their kernel sources.
Signed-off-by: Tom 'spot' Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor cleanups for sparc specific drivers (sunbmac, sunqe, sunlance,
sunhme, esp) so that they have a full module version definition that is
consistent with other upstream drivers.
Signed-off-by: Tom 'spot' Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please apply, SCTP/DCCP needs this when INET_REFCNT_DEBUG
is set.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calculate hashtable size to fit into a page instead of a hardcoded
256 buckets hash table. Results in a 1024 buckets hashtable on
most systems.
Replace old naive extract-8-lsb-bits algorithm with a better
algorithm xor'ing 3 or 4 bit fields at the size of the hashtable
array index in order to improve distribution if the majority of
the lower bits are unused while keeping zero collision behaviour
for the most common use case.
Thanks to Wang Jian <lark@linux.net.cn> for bringing this issue
to attention and to Eran Mann <emann@mrv.com> for the initial
idea for this new algorithm.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SELinux hooks invoke ipv6_skip_exthdr() with an incorrect
length final argument. However, the length argument turns out
to be superfluous.
I was just reading ipv6_skip_exthdr and it occured to me that we can
get rid of len altogether. The only place where len is used is to
check whether the skb has two bytes for ipv6_opt_hdr. This check
is done by skb_header_pointer/skb_copy_bits anyway.
Now it might appear that we've made the code slower by deferring
the check to skb_copy_bits. However, this check should not trigger
in the common case so this is OK.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
And provide an example simply action in order to
demonstrate usage.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Panagiotis Issaris <takis@lumumba.luc.ac.be>
In the ENI155P device driver in six possible failure cases the requested
irq is not being released.
In three of the above possible failure cases additionally there seems to
be a memory leak.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem is that when doing MTU discovery, the too-large segments in
the write queue will be calculated as having a pcount of >1. When
tcp_write_xmit() is trying to send, tcp_snd_test() fails the cwnd test
when pcount > cwnd.
The segments are eventually transmitted one at a time by keepalive, but
this can take a long time.
This patch checks if TSO is enabled when setting pcount.
Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing the open coded equivalents and making ax25 look more like
a linux network protocol, i.e. more similar to inet.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NAT changes in 2.6.11 changed the position where helpers
are called and perform packet mangling. Before 2.6.11, a NAT
helper was called before the packet was NATed and had its
sequence number adjusted. Since 2.6.11, the helpers get packets
with already adjusted sequence numbers.
This breaks sequence number adjustment, adjust_tcp_sequence()
needs the original sequence number to determine whether
a packet was a retransmission and to store it for further
corrections. It can't be reconstructed without more information
than available, so this patch restores the old order by
calling helpers from a new conntrack hook two priorities
below ip_conntrack_confirm() and adjusting the sequence number
from a new NAT hook one priority below ip_conntrack_confirm().
Tracked down by Phil Oester <kernel@linuxace.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
void * __iomem foo is not a pointer to iomem - it's an iomem variable
containing void *. A pile of such guys in arch/sparc64/kernel/time.c,
drivers/sbus/char/rtc.c and include/asm-sparc64/mostek.h turned into
intended void __iomem *.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(!ARCH_S390 && !M68K && !IA64 && !UML) is obviously always true on ARM.
Intended behaviour for ARM is "absent unless we are on RiscPC or
EBSA285". So what we want is added && !ARM in the first term - without
it the last part (|| ARCH_RPC || ARCH_EBSA285, that is) doesn't do
anything.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Missing include, breaks at least on arm.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Turns __get_unaligned() and __put_unaligned into macros. That is
definitely safe; leaving them as inlines breaks on e.g. alpha [try to
build ncpfs there and you'll get unresolved symbols since we end up
getting __get_unaligned() not inlined].
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All boards dealt with by I2C_MPC are 32bit. Moreover, driver simply
won't build on ppc64 - it uses ppc32-only types all over the place.
Dependency fixed - it's PPC32, not PPC.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_HW_CONSOLE selects vt.c; without the stuff pulled by CONFIG_VT it
will not build. Normally we get both in drivers/char/Kconfig and there
HW_CONSOLE depends on VT. sparc64 does not pull drivers/char/Kconfig
and has that sutff in arch/sparc64/Kconfig instead. However, it forgets
to add the same dependency. As the result, turning VT off [which is
possible] will end up with broken build. For no good reason...
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dumb typo - __get_free_page() takes gfp mask (in this case -
GFP_KERNEL), not the page size...
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
zonelist_policy() forgot to mask non-zone bits from gfp when comparing
zone number with policy_zone.
ACKed-by: Andi Kleen <ak@suse.de>
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Somebody forgot that | has higher priority than ?:. As the result,
allocation is done with bogus flags - instead of GFP_ATOMIC + possibly
GFP_DMA we always get GFP_DMA and no GFP_ATOMIC.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
when stealing code from ati_remote for a GPL-driver of my usbradio (because of
its neat usb int transfers) I found out, that the inbuf is freed twice.
I don't have the ati-remote, so I don't know it is a problem at all, but it
looks strange to me anyway. Also I don't know if it has been fixed already in
newer kernel versions.
From: Patrick Boettcher <patrick.boettcher@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a somewhat more comprehensive fix for the problem of devices
like the newer Zaurii ... or in this case some Motorola cell phones.
To recap, the problem's root cause is that these devices aren't using
standard USB class specifications for their network links, and so far
we've had to add lots of device-specific driver entries. The vendor
fix abuses the CDC MDLM descriptors (they _could_ have conformed to
the spec, but didn't) and defines a "Belcarra firmware" pseudo-class.
This patch recognizes that pseudo-class by the GUIDs in those descriptors,
and handles the devices that just use the Zaurus framing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify the ASIX USB Ethernet code to make use of the new status
infrastructure in usbnet.
Additionally, add a link_reset() handler to the struct usbnet
structure to provide a generic means for a driver to perform link
reset tasks such as a determining link speed and setting
device flags accordingly.
Signed-off-by: David Hollis <dhollis@davehollis.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch below adjusts the MODALIAS generated by the usb hotplug
function to match the proposed change to scripts/mod/file2alias.c.
Signed-off-by: Roman Kagan <rkagan@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another attempt at that...
The attached patch fixes the longstanding problem with USB bcdDevice
numeric ranges incorrectly converted into patterns for MODULE_ALIAS
generation. Previously it put both the lower and the upper limits into
the pattern, dlXdhY, making it impossible to fnmatch against except for
a few special cases, like dl*dh* or dlXdhX.
The patch makes it generate multiple MODULE_ALIAS lines covering the
whole range with fnmatch-able patterns. E.g. for a range between 0x0001
and 0x8345 it gives the following patterns:
000[1-9]
00[1-9]*
0[1-9]*
[1-7]*
8[0-2]*
83[0-3]*
834[0-5]
Since bcdDevice is 2 bytes wide = 4 digits in hex representation, the
max no. of patters is 2 * 4 - 1 = 7.
The values are BCD (binary-coded decimals) and not hex, so patterns
using a dash seem to be safe regardless of locale collation order.
The patch changes bcdDevice part of the alias from dlXdhY to dZ, but
this shouldn't have big compatibility issues because fnmatch()-based
modprobing hasn't yet been widely used. Besides, the most common (and
almost the only working) case of dl*dh* becomes d* and thus continues to
work.
The patch is against 2.6.12-rc2, applies to -mm3 with an offset. The
matching patch to fix the MODALIAS environment variable now generated by
the usb hotplug function follows.
Signed-off-by: Roman Kagan <rkagan@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Phil Dibowitz wrote:
> 1. You're adding product IDs 1202, 1203, 1204, and 1205. 1203 was
> already there, but you remove it, OK, but 1205 is already there, so
> you'll need to fix that.
I was not removing 1203, it's just the extension of the bcd range. You are
right about 1205, as I wrote, it was a patch against 2.6.11.7. Attached is
a patch against 2.6.12-rc2.
> 2. I'm OK with the full bcd range if Apple is changing it on firmware
> revs... fine, but it's bcd, not hex... 0x9999 =)
I just copied from other entries. There're a lot 0xffffs in unusual_dev.h,
so I assumed it is correct. I changed it to 0x9999.
> 3. It's rather obnoxious to take the original submitter's credit away.
I didn't remove it, I changed it to "based on...". Because I changed
something (the range) in his entry, I thought it is the best to take the
responsibility but keep the origin. Anyway, in the new patch I did it in a
different way.
> 4. Your /proc/bus/usb/devices shows 1204, but I see no evidence 1202 is
> really an iPod.
I don't have an old iPod mini, but you find a lot of evidence here:
http://www.google.com/search?q=0x1202+ipod
Especially this one:
http://www.qbik.ch/usb/devices/showdescr.php?id=2737
> It also looks like 1205's entry is getting mangled, but I haven't
> attempted to apply the patch, so I'm not sure.
No, the patch was ok, but I agree it looks strange. It's not very
readable, because I cannot tell diff to work blockwise instead of
linewise. Because of the similarity of the entries, diff splits and merges
them. Anyway, the new patch "looks" better. ;-)
Signed-off-by: Sven Anderson <sven-linux@anderson.de>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tom 'spot' Callaway