Without a hwmod for am43xx emif use counting for emif clockdomain does
not happen correctly so it may be shut off by pm code unintentionally.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We support decoding the bootloader values if DEBUG is defined.
But we also need to change the struct omap_hwmod flags to have
HWMOD_INIT_NO_RESET to avoid the GPMC being reset during the
boot. Otherwise just the default timings will be displayed
instead of the bootloader configured timings.
This also allows us to clean up the various GPMC related
hwmod flags. For debugging, we only need HWMOD_INIT_NO_RESET,
and HWMOD_INIT_NO_IDLE is not needed.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
- omap mmc driver supports multiplexing, omap_mmc_hs doesn't
this leads to one of the major confusions in the omap_hsmmc driver
- platform data should be read-only for the driver
most callbacks are not set by the omap3 platform init code while still
required. So they are set from the driver probe function, which is against
the paradigm that platform-data should not be modified by the driver
typical examples are card_detect, read_only callbacks
un-bundling by searching for driver name \"omap_hsmmc in the
arch/arm folder. omap_hsmmc_platform_data is not initialized directly,
but from omap2_hsmmc_info, which is defined in a separate header file
not touched by this patch
hwmod includes platform headers to declare features of the platform. All
the declared features are prefixed OMAP_HSMMC. There is no need to
include platform header from hwmod other except for feature defines
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Only a few files really need that platform header. When later splitting
omap_mmc_platform_data into omap_mmc and omap_mmc_hs, those files
declaring an hs mmc platform data will have to change the platform
include, which is a good sanity check.
Also removing omap242x_init_mmc, which is not used anywhere, checked
with grep.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some of the includes are totally unnecessary, remove some others in
preparation to make the PRCM its own driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: updated to apply; fixed build error on OMAP2xxx-only configs]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add hwmod support for IP's that are present in AM43x, but not in AM335x.
AM43x additional ones added here are,
1. synctimer
2. timer8-11
3. ehrpwm3-5
4. spi2-4
5. gpio4-5
AM43x pruss interconnect which is different as compared to AM335x, has
been taken care.
And register offsets for same hwmod's shared with AM335x is different,
AM43x register offsets are updated appropriately.
ocp clock of those in l4_wkup is fed from "sys_clkin_ck" instead of
"dpll_core_m4_div2_ck", so "ocpif" for those in AM43x l4_wkup has been
added seperately.
hwmod's has been added for those that have main clock (wkup_m3, control,
gpio0) and clock domain (l4_hs) different from AM335x. debugss and
adc_tsc that have different clocks and clockdomains repectively has not
been added due to the reasons mentioned below.
AM43x also has IP's like qspi, hdq1w, vpfe, des, rng, usb, dss, debugss,
adc_tsc. These are not handled here due to both/either of following
reasons,
1. To avoid churn; most of them don't have DT bindings, which would
necessitate adding address space in hwmod, which any way would have
to be removed once DT bindings happen with driver support.
2. patches would come in from sources other than the author
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Hwmod common to AM43x and AM335x has register offsets different. It is
now updated based on SoC detection at run time, hence remove statically
initialized ones.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Most of IP's in AM335x is present on AM43x and so in those cases both
will use same hwmod database (except for a few cases where clock related
details differ), but there is difference w.r.t register offset between
these. Update register offsets at runtime based on the SoC detected to
help in sharing otherwise same hwmod.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
AM335x and AM43x have most of the IP's and interconnect's similar.
Instead of adding redundant hwmod data, move interconnects and hwmod
similar between AM335x and AM43x to a common location. This helps in
reuse on AM43x.
AM335x interconnects that has difference and not present in AM43x are
not moved. ocp clock of those in l4_wkup is fed from a different source
for AM43x. Also pruss interconnect is different.
AM335x hwmod's that has difference other than prcm register offsets
(difference is in clocks of wkup_m3, control, gpio0, debugss and clock
domain of l4_hs, adc_tsc as compared to AM43x) and those that are not
present in AM43x are not moved.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Dave Gerlach