Add a callback to the pll_params for custom dynamic ramping
functions which can be specified per PLL.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add logic which (if specified for a pll) can verify that a PLL is set
to the proper default value and if not can set it. This can be
specified per PLL as each will have different default values.
Based on original work by Aleksandr Frid <afrid@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This code makes use of the SDM fractional divider if present to
constrain the allowable programming range of the PLL divider register
bitfields to take advantage of higher frequency granularity that can
be induced by the SDM divider.
Based on original work by Aleksandr Frid <afrid@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 SoC's have 2 PLLs for memory usage. Add plumbing to register
and handle PLLMB.
PLLMB is used to allow switching between 2 PLLM's without having to use
and intermediate backup PLL, as we need to lock the PLL before we can
switch to it.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra210 SoC's, the logic to enable several of the plls is different
from previous generations. Therefore, add registration functions specific
to Tegra210 which will handle them appropriately.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
ACLK_VIO is the noc bus clock for display module, display cann't
read data from ddr without this clock enabled.
Due to it shouldn't belong to any driver, but we need it enabled,
so just mark it as the CLK_IGNORE_UNUSED flag.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Proper source for MFC block is mout_user_aclk333 (in datasheet named
USER_MUX_ACLK_333), not the output of CLKDIV_ACLK_333 MUX.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Fix cpu clock configuration data for Exynos5422/5800 SoCs
(they use higher PCLK_DBG divider values than Exynos5420 and
support additional frequencies).
Based on Hardkernel's kernel for ODROID-XU3 board.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
With the addition of the new Samsung specific cpu-clock type, the
arm clock can be represented as a cpu-clock type. Add the CPU clock
configuration data and instantiate the CPU clock type for Exynos5420.
Changes by Bartlomiej:
- split Exynos5420 support from the original patches
- moved E5420_[EGL,KFC]_DIV0() macros to clk-exynos5420.c
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds clocks, which are required for preserving parent clock
configuration on GSCL power domain on/off.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
multiplatform and extended DT support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Zhx3
-----END PGP SIGNATURE-----
Merge tag 'realview-base-armsoc-1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/multiplatform
Merge "Realview multiplatform support" from Linus Walleij:
The board and infrastructure changes for RealView
multiplatform and extended DT support.
* tag 'realview-base-armsoc-1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: realview: add an DT SMP boot method
ARM: realview: select SP810 and ICST for the DT variant
soc: versatile: add support for the PB11MPCore
clk: versatile-icst: add device tree support
clk: versatile-icst: refactor to allocate regmap separately
clk: versatile-icst: convert to use regmap
ARM: realview: remove private barrier implementation
ARM: no longer force unbuffered DMA for realview
clk/realview: stop using machine headers
ARM: realview: don't map undefined PCI registers
ARM: realview: remove sparsemem hack
Conflicts:
drivers/clk/versatile/Kconfig
Merge "ARM Versatile multi-platform support" from Rob Herring:
Arnd lit a fire under me to dust this off and get it merged. So here it
is. The main change from prior version is I merged all the code to a
single file. It's a bigger patch than I'd like, but I don't think trying
to do it in multiple steps is worth it.
This is dependent on some solution for the default platform choice on
!MMU builds (allnoconfig) as it can't be Versatile after this series.
Arnd has some ideas on how to address that.
This is tested under QEMU. Linus previously tested this on actual h/w
and had a problem with the display identification which needs
investigation or agreement to worry about it if and when someone
actually cares.
* versatile/multiplatform:
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
With DT support for clocks, irqchips, timers, and PCI now in place, DT
based booting has feature parity with non-DT legacy boot. The final
piece is actually enabling common clock support on Versatile. Enabling
full DT support requires either removing the old Versatile clock code,
updating the legacy boot to use the common clock code, or making DT and
legacy boot mutually exclusive. Given that removing legacy boot code is
the goal anyway, I am going with the 1st option.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds support for the ARM syscon ICST clocks to initialized
directly from the device tree syscon node on ARM Integrator,
Versatile and RealView reference designs.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Break out the registration function so it creates a regmap and
pass to the setup function, so the latter can be shared with
a device tree probe function that already has a regmap.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of passing around register bases, pass around a regmap
in this driver. This refactoring make things so much easier when
we later want to manage an ICST that is part of a syscon.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to move realview into multiplatform, we have to prevent device
drivers from accessing the machine header files.
In case of the clk driver, this is very simple, we just copy the
small set of register definitions into the driver that needs them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function can return negative values, so its result should
be assigned to signed variable.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
"index" needs to be signed for the error handling to work.
Fixes: ab6e23a4e3 ('clk: sunxi: Add H3 clocks support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that was
just added in 4.4, or that has been broken for many years without anyone
noticing.
at91/sama5d2
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin
- fix incorrect clock input for SDIO
exynos
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx
- Fix vf610 SAI clock configuration bug which is discovered by
the newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx
- fix prototypes for readl/writel functions
ls2080a
- use little-endian register access for GPIO and SDHCI
omap
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa
- use PWM lookup table for all ezx machines
s3c24xx
- Remove incorrect __init annotation from s3c24xx cpufreq driver structures.
versatile
- fix PCI IRQ mapping on Versatile PB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fgEd
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that
was just added in 4.4, or that has been broken for many years without
anyone noticing.
at91/sama5d2:
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin:
- fix incorrect clock input for SDIO
exynos:
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx:
- Fix vf610 SAI clock configuration bug which is discovered by the
newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx:
- fix prototypes for readl/writel functions
ls2080a:
- use little-endian register access for GPIO and SDHCI
omap:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of when
MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa:
- use PWM lookup table for all ezx machines
s3c24xx:
- Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
versatile:
- fix PCI IRQ mapping on Versatile PB"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
Reference the newly added efuse clock-ids in the clock-tree.
Signed-off-by: ZhengShunQian <zhengsq@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the clock tree definition for the new rk3228 SoC.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3228's armclk has 3 parents, so allow cpuclk to have
more than 2 parents.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The APBS clock on sun9i is the same as the APB0 clock on sun8i. With
sun9i we are supporting the PRCM clocks by using CLK_OF_DECLARE,
instead of through a PRCM mfd device and subdevices for each clock
and reset control. As such we need a CLK_OF_DECLARE version of
the sun8i-a23-apb0-clk driver.
Also, build it for sun9i/A80, and not just for configurations with
MFD_SUN6I_PRCM enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a new R-Car H3 Clock Pulse Generator / Module Standby and Software
Reset driver, using the new CPG/MSSR driver core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the common core for the new Renesas Clock Pulse Generator / Module
Standby and Software Reset driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Renesas DIV6 clocks provide a single clock output. Hence make the
"clock-output-names" DT property optional instead of mandatory. In case
the DT property is omitted the DT node name will be used.
Rename the variable "name" to "clk_name" to make the code more similar
with fixed-factor-clock.c, and to avoid a conflict with a nested local
variable while we're at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Shmobile is all multiplatform these days, so get rid of the reference to
CONFIG_ARCH_SHMOBILE_MULTI in drivers/clk/shmobile/.
Also instead of always enabling DIV6 and MSTP adjust the Makefile
to enable DIV6 and MSTP depending on if they are included in the
SoC or not.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The video engine has its own special module clock, consisting of a clock
gate, configurable dividers, and a reset control.
On later (sun[68]i) families, the reset control is moved out of this
piece of hardware and grouped with reset controls of other peripherals.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The H3 clock control unit is similar to the those of other sun8i family
members like the A23.
It adds a new bus gates clock similar to the simple gates, but with a
different parent clock for each single gate.
Some of the gates use the new AHB2 clock as parent, whose clock source
is muxable between AHB1 and PLL6/2. The documentation isn't totally clear
about which devices belong to AHB2 now, especially USB EHIC/OHIC, so it
is mostly based on Allwinner kernel source code.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A10/A20 share the same set of DRAM clock gates, which controls
direct memory access for some peripherals.
On the A10, bit 15 controls the system's DRAM clock output (possibly
to the DRAM chips), which we need to keep on.
On the A20 this has been moved to the DRAM controller, becoming a no-op.
However it is still listed in the user manual, so add it anyway.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
BCM63138 has a simple clocking domain which is primarily the ARMPLL
clocking complex, from which the ARM (CPU), APB and AXI clocks would be
derived from.
Since the ARMPLL controller is entirely compatible with the iProc ARM
PLL, we just initialize it without additional parameters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The timer clock aliases are needed early on dm814x. Let's also
add the aliases for the interconnects and MMC.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Due to a copy-paste error the the rk3368 cpuclk settings were acessing
rk3288-specific register offsets. This never caused problems till now,
as cpu frequency scaling in't used currently at all.
Reported-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Contrary to what the datasheet says, the pre divider doesn't seem to be
incremented by one in the PLL2, but just uses the value from the register,
with 0 being a bypass.
This fixes the audio playing too fast.
Since we now have the same pre-divider flags, and the only difference with
the A10 is the post-divider offset, also remove the structure to just pass
the offset as an argument.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: eb662f8547 ("clk: sunxi: pll2: Add A13 support")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently, of_clk_get_parent_name() returns a wrong parent clock name
when "clock-indices" property exists and the target index is not
found in the property. In this case, NULL should be returned.
For example,
oscillator {
compatible = "myclocktype";
#clock-cells = <1>;
clock-indices = <1>, <3>;
clock-output-names = "clka", "clkb";
};
consumer {
compatible = "myclockconsumer";
clocks = <&oscillator 0>, <&oscillator 1>;
};
Currently, of_clk_get_parent_name(consumer_np, 0) returns "clka"
(and of_clk_get_parent_name(consumer_np, 1) also returns "clka",
this is correct). Because the "clock-indices" in the clock parent
does not contain <0>, of_clk_get_parent_name(consumer_np, 0) should
return NULL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add aclk_bus and aclk_peri to the list of rk3368 critical clocks,
which are the base clocks that supply for all peripherals, never
to be disabled automatically.
Signed-off-by: Jianqun xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
To obtain exact pixel clocks, allow the DI clock selectors to influence
the PLLs that they are derived from.
Commit 4591b13289 ("ARM: i.MX6: ipu_di_sel clocks can set parent
rates") did this for i.MX6.
Port it to enable high display resolutions on i.MX53 based platforms
such as CX9020 Embedded PC, too.
Signed-off-by: Patrick Brünn <p.bruenn@beckhoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As we already have a 'imx_check_clocks' to do the clock error
check, so cleanup the error check code.
Signed-off-by: Bai Ping <b51503@freescale.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a virtual arm clk to abstract the actual steps
when changing the ARM core frequency.So we can using
the 'cpufreq-dt' driver on i.MX7D/Solo.
Signed-off-by: Bai Ping <b51503@freescale.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Synchronous Audio Interface (SAI) instances are clocked by
independent clocks: The bus clock and the audio clock (as shown in
Figure 51-1 in the Vybrid Reference Manual). The clock gates in
CCGR0/CCGR1 for SAI0 through SAI3 are bus clock gates, as access
tests to the registers with/without gating those clocks have shown.
The audio clock is gated by the SAIx_EN gates in CCM_CSCDR1,
followed by a clock divider (SAIx_DIV). Currently, the parent of
the bus clock gates has been assigned to SAIx_DIV, which is not
involved in the bus clock path for the SAI instances (see chapter
9.10.12, SAI clocking in the Vybrid Reference Manual).
Fix this by define the parent clock of VF610_CLK_SAIx to be the bus
clock.
If the driver needs the audio clock (when used in master mode), a
fixed device tree is required which assign the audio clock properly
to VF610_CLK_SAIx_DIV.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Most rk3368 boards (especially those with Pmic that followed the lead
from rk3368-evb-act8846) have a PWM regulator on them for vdd_logic.
This is the main voltage for all kinds of misc stuff including the
memory controller.
On these boards it is critically important to make sure that the PWM
never ever glitches and never loses its clock. Any glitch could
crash the system.
Right now there are no users of the PWM regulator and also Linux
thinks that the PWM regulator is disabled. Things happen to work
because firmware configured the PWM and Linux doesn't touch it.
..and the PWM's clock is marked as "ignore unused".
...but things _stop_ working if we turn off serial console. Why?
Because:
1. Serial console shares a parent clock with the PWM (pclk_cpu)
2. If we have no serial console then nobody is holding pclk_cpu on
at reboot time. It gets disabled.
We need to fix a lot of the above problems, but until we get
everything right the cleanest "hack" seems like it is to just keep
the "rk_pwm" clock on always.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Lots of header files are never included outside of a mach-pxa
directory and do not need to be made visible in include/mach,
so let's just move them all down one level.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The mmp clock drivers currently hardcode the physical addresses for
the clock registers. This is generally a bad idea, and it also gets in
the way of multiplatform builds, which make the platform header files
inaccessible to device drivers.
To work around the header file problem, this patch changes the calling
convention so the three mmp clock drivers get initialized with the base
addresses as arguments from the platform code.
It would still be useful to have a larger rework of the clock drivers,
with DT integration to let the clocks actually be probed automatically,
and the base addresses passed as DT properties. I am unsure if anyone
is still interested in the mmp platform, so it is possible that this
won't happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Chao Xie <chao.xie@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
We've been seeing some crashes at reboot test on rk3288-based systems,
which boards have not reset pin connected to NPOR, they reboot by
setting 0xfdb9 to RK3288_GLB_SRST_FST register. If the APLL works in
a high frequency mode, some IPs might hang during soft reset.
It appears that we can fix the problem by switching to slow mode before
reboot, just like what we did before suspend.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The "cpus" clock is the clock for the embedded processor in the A80.
It is also part of the PRCM clock tree. This clock includes a pre-
divider on one of its inputs. For now we are using a custom clock
driver for it. In the future we may want to develop a generalized
driver for these types of clocks, which also includes the AHB clock
driver on sun[5678]i.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds support for the PRCM apbs clock gates found on the
Allwinner A80 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a driver for the multimedia clock controller found on MSM8996
based devices. This should allow most multimedia device drivers
to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The GPU clocks on msm8996 have three dedicated PLLs, MMPLL2,
MMPLL8, and MMPLL9. We leave MMPLL9 at the maximum speed (624
MHz), and we use MMPLL2 and MMPLL8 for the other frequencies. To
make switching frequencies faster, we ping-pong between MMPLL2
and MMPLL8 when we're switching between frequencies that aren't
the maximum. Implement custom rcg clk ops for this type of
frequency switching.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the global clock controller found on MSM8996
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for configuring rates of, enabling, and disabling
Alpha PLLs. This is sufficient for the types of PLLs found in
the global and multimedia clock controllers.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When we use a clk divider with a divider table, we limit the
maximum divider value in divider_get_val() to the
div_mask(width), but when we calculate the divider in
divider_round_rate() we don't consider that the maximum divider
may be limited by the width. Pass the width along to
_get_table_maxdiv() so that we only return the maximum divider
that is valid. This is useful for clocks that want to share the
same divider table while limiting the available dividers to some
subset of the table depending on the width of the bitfield.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
for_each_available_child_of_node performs an of_node_get on each iteration,
so a break out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If get_pll_div() fails we exited by returning NULL but we missed
releasing hwc.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Fixes: 0dfc86b317 ("clk: qoriq: Move chip-specific knowledge into driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
do_div() is meant to be used with an unsigned dividend.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
do_div() is meant to be used with an unsigned dividend.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The word "cases" is doubled. Keep decent forms for the following
lines.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Errata i810 states that DPLL controller can get stuck while transitioning
to a power saving state, while its M/N ratio is being re-programmed.
As a workaround, before re-programming the M/N ratio, SW has to ensure
the DPLL cannot start an idle state transition. SW can disable DPLL
idling by setting the DPLL AUTO_DPLL_MODE=0 or keeping a clock request
active by setting a dependent clock domain in SW_WKUP.
This errata impacts OMAP5 and DRA7 chips, so enable the errata for these.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
sclk_mipidsi_24m is the gating of mipi dsi phy.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The common clk implementation for MMP broke without anyone noticing
when we stopped including linux/clk.h from the clk-provider header.
This did not show up in the defconfig builds because those use the
legacy MMP clk drivers, and it did not show up in my randconfig tests
either because I was testing with my mmp multiplatform series
applied, which at some point gained the fixup.
This fixes the three broken files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 61ae76563e ("clk: Remove clk.h from clk-provider.h")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add 'is_prepared' callback function for pllv3 type clk to make sure when
the system is bootup, the unused clk is in a known state to match the
prepare count info.
Signed-off-by: Bai Ping <b51503@freescale.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'osc' clock is already initialized by the fixed clock defined in
imx25.dtsi. The imx25 clock driver tries to add this clock for a second
time and fails with -EEXIST:
i.MX clk 1: register failed with -17
As the clock is already properly setup in DT with a different driver, we
can completely remove the handling in the imx25 clock driver.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
TI's mux and divider clock drivers do not require locking and they do
not initialize internal spinlocks. This code was occasionally
copy-posted from generic mux/divider drivers. So remove it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add missing clkdev dmtimer related entries for dm816x.
32Khz and ext sources were missing.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the clock tree definition for the new rk3036 SoC.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3036's pll and clock are different with base on the rk3066(rk3188,
rk3288, rk3368 use it), there are different adjust foctors and control
registers, so these should be independent and separate from the series
of rk3066s.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Set the newly added id for the crypto clk, so that it can be called
in other parts.
Signed-off-by: Zain Wang <zain.wang@rock-chips.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Move the xo and sleep clocks to device-tree, instead of hard-coding
them in the driver. This allows us to insert the RPM clocks (if they
are enabled) in between the on-board oscillators and the actual clock.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clk_hw_omap_ops structures are never modified, so declare this one as
const, like the others.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
BCM63138 has a simple clocking domain which is primarily the ARMPLL
clocking complex, from which the ARM (CPU), APB and AXI clocks would be
derived from.
Since the ARMPLL controller is entirely compatible with the iProc ARM
PLL, we just initialize it without additional parameters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
All these clock controllers are little endian devices, but so far
we've been relying on the regmap mmio bus handling this for us
without explicitly stating that fact. After commit 4a98da2164cf
(regmap-mmio: Use native endianness for read/write, 2015-10-29),
the regmap mmio bus will read/write with the __raw_*() IO
accessors, instead of using the readl/writel() APIs that do
proper byte swapping for little endian devices.
So if we're running on a big endian processor and haven't
specified the endianness explicitly in the regmap config or in
DT, we're going to switch from doing little endian byte swapping
to big endian accesses without byte swapping, leading to some
confusing results. On my apq8074 dragonboard, this causes the
device to fail to boot as we access the clock controller with
big endian IO accesses even though the device is little endian.
Specify the endianness explicitly so that the regmap core
properly byte swaps the accesses for us.
Reported-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
quadfs_pll_fs660c32_round_rate prints a few structure members
that are never initialized, and also doesn't print the only one
it cares about. We get a gcc warning about the ones that
are printed:
clk/st/clkgen-fsyn.c:560:93: warning: 'params.sdiv' may be used uninitialized in this function
clk/st/clkgen-fsyn.c:560:93: warning: 'params.mdiv' may be used uninitialized in this function
clk/st/clkgen-fsyn.c:560:93: warning: 'params.pe' may be used uninitialized in this function
clk/st/clkgen-fsyn.c:560:93: warning: 'params.nsdiv' may be used uninitialized in this function
This changes the code to no longer print uninitialized data, and
for good measure it also prints the ndiv member that is being
set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5f7aa9071e ("clk: st: Support for QUADFS inside ClockGenB/C/D/E/F")
Acked-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Commit dca1a4b5ff ("clk: at91: keep slow clk enabled to prevent system
hang") added a workaround for the slow clock as it is not properly handled
by its users.
Now that the slow clock is taken properly by the drivers, this workaround
is not necessary anymore, revert it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The X-Gene clock driver missed the divider shift operation when
set the divider value.
Signed-off-by: Loc Ho <lho@apm.com>
Fixes: 308964caee ("clk: Add APM X-Gene SoC clock driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This is according to figure 12 ("I2C Programming Procedure") in
"Si5351A/B/C Data Sheet"
(https://www.silabs.com/Support%20Documents/TechnicalDocs/Si5351-B.pdf).
Without the PLL soft reset, we were unable to get three outputs
working at the same time.
According to Silicon Labs support, performing PLL soft reset will only
be noticeable if the PLL parameters have been changed.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Signed-off-by: Jens Rudberg <jens@teenage.engineering>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This minor refactoring does not change the function behavior.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This if-block can be dropped because the of_parse_phandle_with_args()
in the following line returns -EINVAL for negative index.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If kzalloc fails we will already have many messages in the log and we do
not need another message to know that kzalloc for sp810 has failed.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PLLM is fixed for Tegra30 up through Tegra114. Starting with Tegra124
PLLM can change rate. Mark PLLM as TEGRA_PLL_FIXED for the generations
where it should be. Modify the check in clk_pll_round_rate() and
clk_pll_recalc_rate() to allow for the non-fixed version to return the
correct rate.
Note that there is no change for Tegra20. This is because PLLM is not
distinguished in that driver, and adding either the PLLM or FIXED_RATE
flags will cause potential problems.
PLLM never supported dynamic ramping. On Tegra20 and Tegra30, there is
no dynamic ramping at all, and on Tegra114, Tegra124 and Tegra132, only
PLLX and PLLC support dynamic ramping, so we can go ahead and remove the
specialized pllm_ops.
Signed-off-by: Danny Huang <dahuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This removes the conversion from pdiv to hw, which is already taken
care of by _get_table_rate before this code is run. This avoids
incorrectly converting pdiv to hw twice and getting the wrong hw value.
Also set the input_rate in the freq cfg in _calc_dynamic_ramp_rate while
setting all the other fields.
In order to prevent regressions on earlier SoC generations, all of the
frequency tables need to be updated so that they contain the actual
divider values. If they contain hardware values these would be converted
to hardware values again, yielding the wrong value.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[treding@nvidia.com: fix regressions on earlier SoC generations]
Signed-off-by: Thierry Reding <treding@nvidia.com>
If a PLL has a reset_reg specified, properly handle that in the
enable/disable logic paths.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For Tegra210, the logic to calculate out-of-table rates is different
from previous generations. Add callbacks that can be overridden to
allow for different ways of calculating rates. Default to
_cal_rate when not specified.
This patch also includes a new flag which is used to set which method
of fixed_mdiv calculation is used. The new method for calculating the
fixed divider value for M can be more accurate especially when
fractional dividers are in play. This allows for older chipsets to use
the existing logic and new generations to use a newer version which
may work better for them.
Based on original work by Aleksandr Frid <afrid@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds logic for taking SDM_DIN (Sigma Delta Modulator) setting into
the equation to calculate the effective N value for PLL which supports
fractional divider.
The effective N = NDIV + 1/2 + SDM_DIN/2^13, where NDIV is the integer
feedback divider.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
SoC specific drivers should define the appropriate flags for each
PLL rather than relying on the registration functions to automatically
set flags on their behalf. This will properly allow for changes between
SoC generations where flags might be different and allow sharing the
same logic functions.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
New SoC's may have more than 3 MISC registers, so bump up the array size
and use a #define to be more informative about the value.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Swap out the generic WARN_ON with a WARN which gives more information
about what is happening.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of having multiple similar wrapper functions for
_clk_pll_[enable|disable], we can simplify it to single
wrappers and use checks to avoid the logic we don't want to use.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Create a wrapper interface to make use of the existing
clk_pll_wait_for_lock. This will be useful for implementations
of callbacks in Tegra SoC specific clock drivers.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has significant differences in muxes for peripheral clocks.
One of the most important changes is that pll_m isn't to be used
as a source for peripherals. Therefore, we need to define the new
muxes and new clocks to use those muxes for Tegra210 support.
Tegra210 has some differences in the PLLP clock tree:
- Four new output clocks: PLLP_OUT_CPU, PLLP_OUT_ADSP, PLLP_OUT_HSIO,
and PLLP_OUT_XUSB.
- PLLP_OUT2 is fixed at 1/2 the rate of PLLP_VCO.
- PLLP_OUT4 is the child of PLLP_OUT_CPU.
Update the xusb_hs_src mux and add the xusb_ssp_src mux for Tegra210.
Including work by Andrew Bresticker <abrestic@chromium.org> and
Bill Huang <bilhuang@nvidia.com>.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The H3 has a usb-phy clk register which is similar to that of earlier
SoCs, but with support for a larger number of phys. So we can simply add
a new set of clk-data and a new compatible and be done with it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Get parent clk names in of_gpio_clk_setup() and store the names
in struct clk_gpio_delayed_register_data instead of doing it from
the clk provider's get() callback. of_clk_get_parent_name() can't
be called in struct of_clk_provider's get() callback since it may
make a call to of_clk_get_from_provider() and this in turn tries
to recursively lock of_clk_mutex.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Cc: Sergej Sawazki <ce3a@gmx.de>
Fixes: 0a4807c2f9 ("clk: Make of_clk_get_parent_name() robust with #clock-cells = 1")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If of_clk_parent_fill() fails then we printed an error message and
returned. But we missed freeing sp810.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use unsigned int for loop variables that can never become negative and
remove a couple of gratuitous blank lines. Also use single spaces around
operators and use a single space instead of a tab to separate comments
from code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The OSC_FREQ field of the OSC_CTRL register uses the value 12 for an
oscillator frequency of 26 MHz, not 260 MHz. This isn't really critical
because I don't think boards with such an oscillator have ever existed,
much less been supported upstream.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a gate clock for controlling all clocks of Security Sub System
(SSS).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Provide support for Sigma Designs Tango4 clock generator.
NOTE: This driver is incompatible with Tango3 clkgen.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[sboyd@codeaurora.org: Add kernel.h include for panic/sprintf]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Put these clocks into the dt files instead of registering them
from C code. This provides a few benefits. It allows us to
specify the frequency of these clocks at the board level instead
of hard-coding them in the driver. It allows us to insert an RPM
clock in between the consumers of the crystals and the actual
clock. And finally, it helps us transition the GCC driver to use
RPM clocks when that configuration is enabled.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We want to put the XO board clocks into the dt files, but we also
need to be backwards compatible with an older dtb. Add an API to
the common code to do this. This also makes a place for us to
handle the case when the RPM clock driver is enabled and we don't
want to register the fixed factor clock.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
As usual, this is the massive branch we have for each release. Lots of
various updates and additions of hardware descriptions on existing hardware,
as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and 32-bit
DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to tell
from the diffstat, so there's little point in duplicating listing it here.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qY1q
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
As we've enabled multiplatform kernels on ARM, and greatly done away with
the contents under arch/arm/mach-*, there's still need for SoC-related
drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
with power management blocks on these SoCs for use by clock, regulator and
bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be confused with
PSCI (Power State Coordination Interface). SCPI is used to communicate with
the assistant embedded cores doing power management, and we have yet to see
how many of them will implement this for their hardware vs abstracting in
other ways (or not at all like in the past).
- To make confusion between SCPI and PSCI more likely, this release also
includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWQC+cAAoJEIwa5zzehBx3jEUP/0GpxfDVanEUkudVLLe7J0RH
CNlRan107Cw6hXRUJo7elEsuCALjccXjc1CAH4+RnNpOAeBKW97n+WU7trTv+wUZ
sQX4SkBPKFBlgwGF2qhsi5q74gms/BrgtCa4kNb9joOYso039tlfIOPzK80DMkOm
TkyIJdUCgFJMjCQLhX6kGT0PDcrbIjb6aA2cF3FAVeaJA7uz8lNe/eHJr3oHxIEY
CvC651yJ2mIHQUU4BJx/AJo+wXg3dRUXNCAtBjwLRPEAzduYZXYm1ZTVIby/1q9r
dR2KDFEuibODXmXrDBzKNJwCu/TLJEwo/1oPaEIVfY91XLKfiWUhgVqa1o1I+d9U
XoGPibCW461qFahjQW87MfInALpCOA7/RbTNjFp+MVyipCYvkaYq7KFiYEldgFDx
z4Qx/J4hYc2TlDWrpNiUCZMfmhwi7y+Ib+tnenYTO1eyMuw0e9mfnVdjk5iU3Pvk
Ye4qPqpYclJruyHbYi164878+1lLaW2NCUgC3rkBO/GWPAzp7d9iLWoZ3PuyD5i5
PEjs668UcRdZYbI4rdrhGHL8Eq9Gnuc4Rthu7HxPOK+DG0XgP8r97PhM8aYGYVDO
+yikBtjWRsA9fPj3rMKA3UsQ61DAeR9LmZ0XPGjWFMCjCG0JlUoIMaA+Uu0i8fr8
95qxBVxbO7rhL39r1rhV
=dm+I
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
New and/or improved SoC support for this release:
- Marvell Berlin:
* Enable standard DT-based cpufreq
* Add CPU hotplug support
- Freescale:
* Ethernet init for i.MX7D
* Suspend/resume support for i.MX6UL
- Allwinner:
* Support for R8 chipset (used on NTC's $9 C.H.I.P board)
- Mediatek:
* SMP support for some platforms
- Uniphier:
* L2 support
* Cleaned up SMP support, etc.
+ A handful of other patches around above functionality, and a few other
smaller changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=h5xk
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New and/or improved SoC support for this release:
Marvell Berlin:
- Enable standard DT-based cpufreq
- Add CPU hotplug support
Freescale:
- Ethernet init for i.MX7D
- Suspend/resume support for i.MX6UL
Allwinner:
- Support for R8 chipset (used on NTC's $9 C.H.I.P board)
Mediatek:
- SMP support for some platforms
Uniphier:
- L2 support
- Cleaned up SMP support, etc.
plus a handful of other patches around above functionality, and a few
other smaller changes"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
ARM: uniphier: rework SMP operations to use trampoline code
ARM: uniphier: add outer cache support
Documentation: EXYNOS: Update bootloader interface on exynos542x
ARM: mvebu: add broken-idle option
ARM: orion5x: use mac_pton() helper
ARM: at91: pm: at91_pm_suspend_in_sram() must be 8-byte aligned
ARM: sunxi: Add R8 support
ARM: digicolor: select pinctrl/gpio driver
arm: berlin: add CPU hotplug support
arm: berlin: use non-self-cleared reset register to reset cpu
ARM: mediatek: add smp bringup code
ARM: mediatek: enable gpt6 on boot up to make arch timer working
soc: mediatek: Fix random hang up issue while kernel init
soc: ti: qmss: make acc queue support optional in the driver
soc: ti: add firmware file name as part of the driver
Documentation: dt: soc: Add description for knav qmss driver
ARM: S3C64XX: Use PWM lookup table for mach-smartq
ARM: S3C64XX: Use PWM lookup table for mach-hmt
ARM: S3C64XX: Use PWM lookup table for mach-crag6410
ARM: S3C64XX: Use PWM lookup table for smdk6410
...
Merging in the few patches I had kept separate from main next/dt, since others
got merged here directly.
* next/arm64:
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
arm64: dts: mt8173: Add clocks for SCPSYS unit
arm64: dts: mt8173: Add subsystem clock controller device nodes
+ Linux 4.3-rc5
- Kconfig: remove BE-only platforms from LE kernel build from Boqun Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference. from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from Colin Ian King
- Disable hugepd for 64K page size. from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file. from Paul Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages. from Christophe Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e kexec/kdump
support, a rework of the qoriq clock driver, device tree changes including
qoriq fman nodes, support for a new 85xx board, and some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for MPC512x
LocalPlus Bus FIFO with its device tree binding documentation, mpc512x
device tree updates and some minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YwcM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Kconfig: remove BE-only platforms from LE kernel build from Boqun
Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael
Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar
K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan
Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel
Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference, from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from
Colin Ian King
- Disable hugepd for 64K page size, from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh
Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file, from Paul
Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael
Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael
Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe
Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael
Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis
Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages, from Christophe
Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro
Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from
Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building
with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e
kexec/kdump support, a rework of the qoriq clock driver, device tree
changes including qoriq fman nodes, support for a new 85xx board, and
some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for
MPC512x LocalPlus Bus FIFO with its device tree binding
documentation, mpc512x device tree updates and some minor fixes.
* tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (106 commits)
powerpc/msi: Fix section mismatch warning in msi_bitmap_alloc()
powerpc/prom: Use of_get_next_parent() in of_get_ibm_chip_id()
powerpc/pseries: Correct string length in pseries_of_derive_parent()
powerpc/e6500: hw tablewalk: make sure we invalidate and write to the same tlb entry
powerpc/mpc85xx: Add FSL QorIQ DPAA FMan support to the SoC device tree(s)
powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan
powerpc/fsl: Add #clock-cells and clockgen label to clockgen nodes
powerpc: handle error case in cpm_muram_alloc()
powerpc: mpic: use IRQCHIP_SKIP_SET_WAKE instead of redundant mpic_irq_set_wake
powerpc/book3e-64: Enable kexec
powerpc/book3e-64/kexec: Set "r4 = 0" when entering spinloop
powerpc/booke: Only use VIRT_PHYS_OFFSET on booke32
powerpc/book3e-64/kexec: Enable SMP release
powerpc/book3e-64/kexec: create an identity TLB mapping
powerpc/book3e-64: Don't limit paca to 256 MiB
powerpc/book3e/kdump: Enable crash_kexec_wait_realmode
powerpc/book3e: support CONFIG_RELOCATABLE
powerpc/booke64: Fix args to copy_and_flush
powerpc/book3e-64: rename interrupt_end_book3e with __end_interrupts
powerpc/e6500: kexec: Handle hardware threads
...
support. The core framework is mostly unchanged this time
around, with only a couple patches to expose a clk provider
API and make getting clk parent names from DT more robust.
Driver updates:
- Support for clock controllers found on Broadcom Northstar
SoCs and bcm2835 SoC
- Support for Allwinner audio clocks
- A few cleanup patches for Tegra drivers and support for the
highest DFLL frequencies on Tegra124
- Samsung exynos7 fixes and improvements
- i.Mx SoC updates to add a few missing clocks and keep debug
uart clocks on during kernel intialization
- Some mediatek cleanups and support for more subsystem clocks
- Support for msm8916 gpu/audio clocks and qcom's GDSC power domain
controllers
- A new driver for the Silabs si514 clock chip
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=K6iN
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-20151104' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The majority of the changes are driver updates and new device support.
The core framework is mostly unchanged this time around, with only a
couple patches to expose a clk provider API and make getting clk
parent names from DT more robust.
Driver updates:
- Support for clock controllers found on Broadcom Northstar SoCs and
bcm2835 SoC
- Support for Allwinner audio clocks
- A few cleanup patches for Tegra drivers and support for the highest
DFLL frequencies on Tegra124
- Samsung exynos7 fixes and improvements
- i.Mx SoC updates to add a few missing clocks and keep debug uart
clocks on during kernel intialization
- Some mediatek cleanups and support for more subsystem clocks
- Support for msm8916 gpu/audio clocks and qcom's GDSC power domain
controllers
- A new driver for the Silabs si514 clock chip"
* tag 'clk-for-linus-20151104' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (143 commits)
clk: qcom: msm8960: Fix dsi1/2 halt bits
clk: lpc18xx-cgu: fix potential system hang when disabling unused clocks
clk: lpc18xx-ccu: fix potential system hang when disabling unused clocks
clk: Add clk_hw_is_enabled() for use by clk providers
clk: Add stubs for of_clk_*() APIs when CONFIG_OF=n
clk: versatile-icst: fix memory leak
clk: Remove clk_{register,unregister}_multiplier()
clk: iproc: define Broadcom NS2 iProc clock binding
clk: iproc: define Broadcom NSP iProc clock binding
clk: ns2: add clock support for Broadcom Northstar 2 SoC
clk: iproc: Separate status and control variables
clk: iproc: Split off dig_filter
clk: iproc: Add PLL base write function
clk: nsp: add clock support for Broadcom Northstar Plus SoC
clk: iproc: Add PWRCTRL support
clk: cygnus: Convert all macros to all caps
ARM: cygnus: fix link failures when CONFIG_COMMON_CLK_IPROC is disabled
clk: imx31: add missing of_node_put
clk: imx27: add missing of_node_put
clk: si5351: add missing of_node_put
...
- Add new API to set VCCQ voltage - mmc_regulator_set_vqmmc()
- Add new ioctl to allow userspace to send multi commands
- Wait for card busy signalling before starting SDIO requests
- Remove MMC_CLKGATE
- Enable tuning for DDR50 mode
- Some code clean-up/improvements to mmc pwrseq
- Use highest priority for eMMC restart handler
- Add DT bindings for eMMC hardware reset support
- Extend the mmc_send_tuning() API
- Improve ios show for debugfs
- A couple of code optimizations
MMC host:
- Some generic OF improvements
- Various code clean-ups
- sirf: Add support for DDR50
- sunxi: Add support for card busy detection
- mediatek: Use MMC_CAP_RUNTIME_RESUME
- mediatek: Add support for eMMC HW-reset
- mediatek: Add support for HS400
- dw_mmc: Convert to use the new mmc_regulator_set_vqmmc() API
- dw_mmc: Add external DMA interface support
- dw_mmc: Some various improvements
- dw_mmc-rockchip: MMC tuning with the clock phase framework
- sdhci: Properly clear IRQs during resume
- sdhci: Enable tuning for DDR50 mode
- sdhci-of-esdhc: Use IRQ mode for card detection
- sdhci-of-esdhc: Support both BE and LE host controller
- sdhci-pci: Build o2micro support in the same module
- sdhci-pci: Support for new Intel host controllers
- sdhci-acpi: Support for new Intel host controllers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gn/m
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.4' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add new API to set VCCQ voltage - mmc_regulator_set_vqmmc()
- Add new ioctl to allow userspace to send multi commands
- Wait for card busy signalling before starting SDIO requests
- Remove MMC_CLKGATE
- Enable tuning for DDR50 mode
- Some code clean-up/improvements to mmc pwrseq
- Use highest priority for eMMC restart handler
- Add DT bindings for eMMC hardware reset support
- Extend the mmc_send_tuning() API
- Improve ios show for debugfs
- A couple of code optimizations
MMC host:
- Some generic OF improvements
- Various code clean-ups
- sirf: Add support for DDR50
- sunxi: Add support for card busy detection
- mediatek: Use MMC_CAP_RUNTIME_RESUME
- mediatek: Add support for eMMC HW-reset
- mediatek: Add support for HS400
- dw_mmc: Convert to use the new mmc_regulator_set_vqmmc() API
- dw_mmc: Add external DMA interface support
- dw_mmc: Some various improvements
- dw_mmc-rockchip: MMC tuning with the clock phase framework
- sdhci: Properly clear IRQs during resume
- sdhci: Enable tuning for DDR50 mode
- sdhci-of-esdhc: Use IRQ mode for card detection
- sdhci-of-esdhc: Support both BE and LE host controller
- sdhci-pci: Build o2micro support in the same module
- sdhci-pci: Support for new Intel host controllers
- sdhci-acpi: Support for new Intel host controllers"
* tag 'mmc-v4.4' of git://git.linaro.org/people/ulf.hansson/mmc: (73 commits)
mmc: dw_mmc: fix the wrong setting for UHS-DDR50 mode
mmc: dw_mmc: fix the CardThreshold boundary at CardThrCtl register
mmc: dw_mmc: NULL dereference in error message
mmc: pwrseq: Use highest priority for eMMC restart handler
mmc: mediatek: add HS400 support
mmc: mmc: extend the mmc_send_tuning()
mmc: mediatek: add implement of ops->hw_reset()
mmc: mediatek: fix got GPD checksum error interrupt when data transfer
mmc: mediatek: change the argument "ddr" to "timing"
mmc: mediatek: make cmd_ints_mask to const
mmc: dt-bindings: update Mediatek MMC bindings
mmc: core: Add DT bindings for eMMC hardware reset support
mmc: omap_hsmmc: Enable omap_hsmmc for Keystone 2
mmc: sdhci-acpi: Add more ACPI HIDs for Intel controllers
mmc: sdhci-pci: Add more PCI IDs for Intel controllers
arm: lpc18xx_defconfig: remove CONFIG_MMC_DW_IDMAC
arm: hisi_defconfig: remove CONFIG_MMC_DW_IDMAC
arm: exynos_defconfig: remove CONFIG_MMC_DW_IDMAC
arc: axs10x_defconfig: remove CONFIG_MMC_DW_IDMAC
mips: pistachio_defconfig: remove CONFIG_MMC_DW_IDMAC
...
This is a major overhaul of the clk-qoriq driver, which I'm merging
via PPC with Stephen Boyd's ack in order to apply subsequent PPC patches
that depend on it.
Pull ARM fixes from Russell King:
"Two fixes for ARM and one for clkdev:
- Fix another build issue with vdsomunge on non-glibc systems
- Fix a randconfig build error caused by an invalid configuration
- Fix a clkdev problem causing the Nokia n700 to no longer boot"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
clkdev: fix clk_add_alias() with a NULL alias device name
ARM: 8445/1: fix vdsomunge not to depend on glibc specific byteswap.h
ARM: make RiscPC depend on MMU
The halt bits for these clocks seem wrong. I get the following
warning while booting on an msm8960-cdp:
WARNING: CPU: 0 PID: 1 at drivers/clk/qcom/clk-branch.c:97 clk_branch_toggle+0xd0/0x138()
dsi1_clk status stuck at 'on'
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.3.0-rc3-00113-g5532cfb567fe #110
Hardware name: Qualcomm (Flattened Device Tree)
[<c0216984>] (unwind_backtrace) from [<c02138f8>] (show_stack+0x10/0x14)
[<c02138f8>] (show_stack) from [<c04a525c>] (dump_stack+0x70/0xbc)
[<c04a525c>] (dump_stack) from [<c0223c70>] (warn_slowpath_common+0x78/0xb4)
[<c0223c70>] (warn_slowpath_common) from [<c0223d40>] (warn_slowpath_fmt+0x30/0x40)
[<c0223d40>] (warn_slowpath_fmt) from [<c05fc2dc>] (clk_branch_toggle+0xd0/0x138)
[<c05fc2dc>] (clk_branch_toggle) from [<c05f3f3c>] (clk_disable_unused_subtree+0x98/0x1b0)
[<c05f3f3c>] (clk_disable_unused_subtree) from [<c05f3ec4>] (clk_disable_unused_subtree+0x20/0x1b0)
[<c05f3ec4>] (clk_disable_unused_subtree) from [<c05f5474>] (clk_disable_unused+0x58/0xd8)
[<c05f5474>] (clk_disable_unused) from [<c0209710>] (do_one_initcall+0xac/0x1ec)
[<c0209710>] (do_one_initcall) from [<c0991db4>] (kernel_init_freeable+0x11c/0x1e8)
[<c0991db4>] (kernel_init_freeable) from [<c0727ae0>] (kernel_init+0x8/0xec)
[<c0727ae0>] (kernel_init) from [<c0210238>] (ret_from_fork+0x14/0x3c)
Fix the status bits and the errors go away.
Fixes: 5532cfb567 ("clk: qcom: mmcc-8960: Add DSI related clocks")
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clock consumer (CCU) of the CGU must be able to check if a CGU
base clock is really running since access to the CCU registers
requires a running base clock. Access with a disabled base clock will
cause the system to hang. Fix this issue by adding code that check if
the parent clock is running in the is_enabled clk_ops callback. Since
certain clocks can be cascaded this must be added to all clock gates.
The hang would occur if the boot ROM or boot loader didn't setup and
enable the USB0 clock. Then when the clk framework tried to access
the CCU register it would hang the system.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
CCU branch clock register must only be accessed while the base
(parent) clock is running. Access with a disabled base clock
will cause the system to hang. Fix this issue by adding code
that check if the parent clock is running in the is_enabled
clk_ops callback.
This hang would occur when disabling unused clocks after AMBA
runtime pm had already disabled some of the clocks.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add clk_hw_is_enabled() to the provider APIs so clk providers can
use a struct clk_hw instead of a struct clk to check if a clk is
enabled or not.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Let's use DIV_ROUND_CLOSEST for rounding, not just truncating
division. This lets us get closer to the right rate.
Before this:
set_phase(86) delay_nums=26 reg[0xf000420c]=0x468 actual_degrees=83
set_phase(89) delay_nums=27 reg[0xf000420c]=0x46c actual_degrees=86
After this:
set_phase(86) delay_nums=27 reg[0xf000420c]=0x46c actual_degrees=86
set_phase(89) delay_nums=28 reg[0xf000420c]=0x470 actual_degrees=90
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because of the inexact nature of the extra MMC delay elements (it's
not possible to keep the phase monotonic and to also make phases (mod
90) > 70), we previously only allowed phases (mod 90) of 22.5, 45,
and 67.5.
But it's not the end of the world if the MMC clock phase goes
non-monotonic. At most we'll be 25 degrees off. It's way better to
test more phases to look for bad ones than to be 25 degrees off, because
in the case of MMC really the point is to find bad phases and get as far
asway from the as possible. If we get to test extra phases by going
slightly non-monotonic then that might be fine. Worst case we would
end up at a phases that's slight differnt than the one we wanted, but
at least we'd still be quite far away from the a bad phase.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Fold in more precise variance-values of 44-77 instead of 40-80.
Fold in the actual removal of the monotonic requirement and adapt
patch message accordingly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Support for the Audio PLL and child clocks
- Support for the A33 AHB gates
- New clk-multiplier generic driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WtVW
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clocks-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Bringing in the sunxi clock branch since it introduces header file contents
that is needed by the DT branch. This is a stable tag shared with the clk tree.
Allwinner clock additions for 4.4
- Support for the Audio PLL and child clocks
- Support for the A33 AHB gates
- New clk-multiplier generic driver
* tag 'sunxi-clocks-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi: mod1 clock support
clk: sunxi: codec clock support
clk: sunxi: pll2: Add A13 support
clk: sunxi: Add a driver for the PLL2
clk: Add a basic multiplier clock
clk: sunxi: Add A33 gates support
Signed-off-by: Olof Johansson <olof@lixom.net>
This pull request contains the DT changes for BCM2835 in 4.4. It
pulls in clk/clk-bcm2835 (which Stephen Boyd has said would be stable)
because the DT changes to enable the clock driver need the driver
itself to be present. These changes include the following:
- Eric Anholt, moves the bcm2835 clock driver under bcm/ where it belongs with
other Broadcom clock providers drivers, defines the binding for new clock
driver, adds support for programming the BCM2835 audio domain, adds the DDC I2C
controller to Device Tree, and finally migrates the Device Tree to use the new
clock driver binding
- Lubomir Rintel adds support for the Raspberry Pi Model A+ and B revision 2, and
remove the I2S controller which is non-existent on Raspberry Pi Model B
- Stefan Wahren adds an uart0 label for referencing the UART adapter
* tag 'arm/soc/for-4.4/rpi-dt-v2' of https://github.com/Broadcom/stblinux:
ARM: bcm2835: Add the DDC I2C controller to the device tree.
ARM: bcm2835: Switch to using the new clock driver support.
ARM: bcm2835: dt: Add Raspberry Pi Model A+
ARM: bcm2835: dt: Add Raspberry Pi Model B rev2
ARM: bcm2835: dt: Raspberry Pi Model B had no I2S
ARM: bcm2835: add label for uart0
clk: bcm2835: Add support for programming the audio domain clocks
clk: bcm2835: Add binding docs for the new platform clock driver.
clk: bcm2835: Move under bcm/ with other Broadcom SoC clk drivers.
Signed-off-by: Olof Johansson <olof@lixom.net>
- use exynos5420-dw-mshc instead of exynos5250 for exynos3250
- add DISP1 clocks and the DISP1 power domain of two closk
on exynos5250 (clock commit got Stephen's ack)
- add vbus regulators on exynos3250, exynos4210 and exynos4412 boards
- fix typo in regulator enable GPIO property on s5pv20-aquila and goni
- document: correct the example of exynos power domain clocks
- document: consolidate exynos SoC dt-bindings and non-Samsung
boards related compatibles (FriendlyARM, Google, Hardkernel
and Insignal)
- update MAINTAINER entries accordingly (documentation)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=UPmG
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Samsung 2nd DT updates for v4.4
- use exynos5420-dw-mshc instead of exynos5250 for exynos3250
- add DISP1 clocks and the DISP1 power domain of two closk
on exynos5250 (clock commit got Stephen's ack)
- add vbus regulators on exynos3250, exynos4210 and exynos4412 boards
- fix typo in regulator enable GPIO property on s5pv20-aquila and goni
- document: correct the example of exynos power domain clocks
- document: consolidate exynos SoC dt-bindings and non-Samsung
boards related compatibles (FriendlyARM, Google, Hardkernel
and Insignal)
- update MAINTAINER entries accordingly (documentation)
* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
MAINTAINERS: Add documentation and dt-bindings for exynos stuff
dt-bindings: EXYNOS: Document compatibles from other vendors
dt-bindings: Consolidate Exynos SoC bindings
ARM: dts: Add clocks to DISP1 domain in exynos5250
dt-bindings: Correct the example for Exynos power domain clocks
ARM: dts: Fix typo in regulator enable GPIO property in s5pv210-goni
ARM: dts: Fix typo in regulator enable GPIO property in s5pv210-aquila
ARM: dts: Add vbus regulator to USB2 phy nodes on exynos3250, exynos4210 and exynos4412 boards
clk: samsung: exynos5250: Add DISP1 clocks
ARM: dts: use exynos5420-dw-mshc compatible for exynos3250
Signed-off-by: Olof Johansson <olof@lixom.net>
A static code checker found a memory leak in the Versatile
ICST code. Fix it.
Fixes: a183da637c "clk: versatile: respect parent rate in ICST clock"
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These APIs aren't used, so remove them. This can be reverted if
we get a user at some point.
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Suggested-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When the DISP1 power domain is powered off, there's two clocks that need
to be temporarily reparented to OSC, and back to their original parents
when the domain is powered on again.
We expose these two clocks in the DT bindings so that the DT node of the
power domain can reference them.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
- Add IOMUXC LPSR (Low Power State Retention) device for i.MX7D.
- Add a few low power mode related devices and touch controller for
i.MX6UL.
- Add a number of devices for i.MX7D SDB board support, USB, Dual FEC,
and eMMC5.0.
- i.MX6 Boundary Devices updates: relicense under GPLv2/X11, add Okaya
LCD, touch and wifi support, add new boards Nitrogen6_Lite and
Nitrogen6_Max.
- Enable touch screen and NAND Flash controller for a few Vybrid
devices.
- Some random and small updates on LS1021A and MXS support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWJQUPAAoJEFBXWFqHsHzOo+cH/irx+abVdFV97q6M0VwFsQ3/
Tf4/CsdiTjM5ZDrKZEtXzP8BZl+ZO4tQXLspP+wVceQ+PVUiVvdAHu0l68iuJRrA
+Bj9VrLIzMDf7FVpzbZHZD3kd1NALGh/5i0TerkuZMNl1KH57HyGjLnjKH43n7uz
mFPeZFAQMwSjEnRJj/6217Itqi+LurARJsnXQs6uhQ7feSsA88HU3EQ8QsiZqiAu
MULAJBYaE09shlokuXIKx67t8outdb8C0Uue64nt42y8NR0m5eVVG7NJoF+23T6C
CRX5zveYa7D2QXTkihvjdRpazhLiPnwV3RCVejLOZMk0G14hD9U39jkTp+9ws1w=
=kPBq
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree changes for 4.4:
- Add IOMUXC LPSR (Low Power State Retention) device for i.MX7D.
- Add a few low power mode related devices and touch controller for
i.MX6UL.
- Add a number of devices for i.MX7D SDB board support, USB, Dual FEC,
and eMMC5.0.
- i.MX6 Boundary Devices updates: relicense under GPLv2/X11, add Okaya
LCD, touch and wifi support, add new boards Nitrogen6_Lite and
Nitrogen6_Max.
- Enable touch screen and NAND Flash controller for a few Vybrid
devices.
- Some random and small updates on LS1021A and MXS support.
* tag 'imx-dt-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (53 commits)
ARM: dts: ls1021a: Add quirk for Erratum A009116
ARM: imx6sx-sdb: Fix typo in regulator enable GPIO property
ARM: dts: imx6: phyFLEX: fix typo in "pinctrl-names"
ARM: dts: imx6: change the core clock of spdif
ARM: dts: vf-colibri: enable NAND flash controller
ARM: dts: vf610twr: add NAND flash controller peripherial
ARM: dts: imx: add Boundary Devices Nitrogen6_Lite board
ARM: dts: imx: add Boundary Devices Nitrogen6_Max board
ARM: dts: imx6dl-nitrogen6x: change manufacturer to Boundary Devices
ARM: dts: imx6q-nitrogen6x: change manufacturer to Boundary Devices
of: Add Boundary Devices Inc. vendor prefix
ARM: dts: imx6qdl-sabrelite: relicense under GPLv2/X11
ARM: dts: imx6qdl-nitrogen6x: relicense under GPLv2/X11
ARM: dts: imx6qdl-nitrogen6x: add wifi wl1271 support
ARM: dts: imx6dql-nitrogen6x: add touchscreen support
ARM: dts: imx6qdl-sabrelite: add Okaya LCD panel
ARM: dts: imx6qdl-nitrogen6x: add Okaya LCD panel
ARM: dts: vf500-colibri: Add device tree node for touchscreen support
ARM: dts: i.MX35: fix cpu compatible value
ARM: dts: i.MX31: fix cpu compatible value
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for the Allwinner R8 SoC used in the CHIP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o6P8
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/soc
Allwinner core changes for 4.4
Add support for the Allwinner R8 SoC used in the CHIP.
* tag 'sunxi-core-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: Add R8 support
Signed-off-by: Olof Johansson <olof@lixom.net>
* clk-iproc:
clk: iproc: define Broadcom NS2 iProc clock binding
clk: iproc: define Broadcom NSP iProc clock binding
clk: ns2: add clock support for Broadcom Northstar 2 SoC
clk: iproc: Separate status and control variables
clk: iproc: Split off dig_filter
clk: iproc: Add PLL base write function
clk: nsp: add clock support for Broadcom Northstar Plus SoC
clk: iproc: Add PWRCTRL support
clk: cygnus: Convert all macros to all caps
ARM: cygnus: fix link failures when CONFIG_COMMON_CLK_IPROC is disabled
The Broadcom Northstar 2 SoC is architected under the iProc
architecture. It has the following PLLs: GENPLL SCR, GENPLL SW,
LCPLL DDR, LCPLL Ports, all derived from an onboard crystal.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some PLLs have separate registers for Status and Control. The means the
pll_base needs to be split into 2 new variables, so that those PLLs can
specify device tree registers for those independently. Also, add a new
driver flag to identify this presence of the split, and let the driver
know that additional registers need to be used.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The PLL loop filter/gain can be located in a separate register on some
SoCs. Split these off into a separate variable, so that an offset can
be added if necessary. Also, make the necessary modifications to the
Cygnus and NSP drivers for this change.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
All writes to the PLL base address must be flushed if the
IPROC_CLK_NEEDS_READ_BACK flag is set. If we add a function to make the
necessary write and reads, we can make sure that any future code which
makes PLL base writes will do the correct thing.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Broadcom Northstar Plus SoC is architected under the iProc
architecture. It has the following PLLs: ARMPLL, GENPLL, LCPLL0, all
derived from an onboard crystal.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some iProc SoC clocks use a different way to control clock power, via
the PWRDWN bit in the PLL control register. Since the PLL control
register is used to access the PWRDWN bit, there is no need for the
pwr_base when this is being used. A new flag, IPROC_CLK_EMBED_PWRCTRL,
has been added to identify this usage. We can use the AON interface to
write the values to enable/disable PWRDOWN.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
[sboyd@codeaurora.org: Remove useless parentheses]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The macros that are being used to initialize the values of the clk
structures should be all caps. Find and replace all of them with their
relevant counterparts.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When CONFIG_CYGNUS is set but CONFIG_COMMON_CLK_IPROC is disabled, the
following link failures are caused:
drivers/built-in.o: In function `cygnus_armpll_init':
:(.init.text+0x1d290): undefined reference to `iproc_armpll_setup'
drivers/built-in.o: In function `cygnus_genpll_clk_init':
:(.init.text+0x1d2c4): undefined reference to `iproc_pll_clk_setup'
drivers/built-in.o: In function `cygnus_lcpll0_clk_init':
:(.init.text+0x1d304): undefined reference to `iproc_pll_clk_setup'
drivers/built-in.o: In function `cygnus_mipipll_clk_init':
:(.init.text+0x1d344): undefined reference to `iproc_pll_clk_setup'
drivers/built-in.o: In function `cygnus_asiu_init':
:(.init.text+0x1d370): undefined reference to `iproc_asiu_setup'
It is fixed it by always selecting COMMON_CLK_IPROC from
ARCH_BCM_IPROC, and making COMMON_CLK_IPROC a silent option (thus
preventing it from being erroneously disabled by a user).
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- Support for the Audio PLL and child clocks
- Support for the A33 AHB gates
- New clk-multiplier generic driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WtVW
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clocks-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Pull Allwinner clock additions for 4.4 from Maxime Ripard:
- Support for the Audio PLL and child clocks
- Support for the A33 AHB gates
- New clk-multiplier generic driver
* tag 'sunxi-clocks-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi: mod1 clock support
clk: sunxi: codec clock support
clk: sunxi: pll2: Add A13 support
clk: sunxi: Add a driver for the PLL2
clk: Add a basic multiplier clock
clk: sunxi: Add A33 gates support
for_each_compatible_node performs an of_node_get on each iteration, so a
break out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e;
@@
for_each_compatible_node(n,...) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
for_each_compatible_node performs an of_node_get on each iteration, so a
break out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e;
@@
for_each_compatible_node(n,...) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
The resulting puts were manually moved to the end of the function for
conciseness.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
for_each_matching_node_and_match performs an of_node_get on each iteration,
so a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression e1,e2,e;
local idexpression np;
@@
for_each_matching_node_and_match(np, e1, e2) {
... when != of_node_put(np)
when != e = np
(
return np;
|
+ of_node_put(np);
? return ...;
)
...
}
// </smpl>
Besides the problem identified by the semantic patch, this patch adds an
of_node_get in front of saving np in a field of parent, to account for the
fact that this value will be put on going on to the next element in the
iteration, and then adds of_node_puts in the two loops where the parent
pointer can be freed.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
LS2080A is the first implementation of the chassis 3 clockgen, which
has a different register layout than previous chips. It is also little
endian, unlike previous chips.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
The device tree should describe the chips (or chip-like subblocks) in
the system, but it generally does not describe individual registers --
it should identify, rather than describe, a programming interface.
This has not been the case with the QorIQ clockgen nodes. The
knowledge of what each bit setting of CLKCnCSR means is encoded in
three places (binding, pll node, and mux node), and the last also needs
to know which options are valid on a particular chip. All three of
these locations are considered stable ABI, making it difficult to fix
mistakes (of which I have found several), much less refactor the
abstraction to be able to address problems, limitations, or new chips.
Under the current binding, a pll clock specifier of 2 means that the
PLL is divided by 4 -- and the driver implements this, unless there
happen to be four clock-output-names rather than 3, in which case it
interprets it as PLL divided by 3. This does not appear in the binding
documentation at all. That hack is now considered stable ABI.
The current device tree nodes contain errors, such as saying that
T1040 can set a core clock to PLL/4 when only PLL and PLL/2 are options.
The current binding also ignores some restrictions on clock selection,
such as p5020's requirement that if a core uses the "wrong" PLL, that
PLL must be clocked lower than the "correct" PLL and be at most 80% of
the rated CPU frequency.
Possibly because of the lack of the ability to express such nuance in
the binding, some valid options are omitted from the device trees, such
as the ability on p4080 to run cores 0-3 from PLL3 and cores 4-7 from
PLL1 (again, only if they are at most 80% of rated CPU frequency).
This omission, combined with excessive caution in the cpufreq driver
(addressed in a subsequent patch), means that currently on a 1500 MHz
p4080 with typical PLL configuration, cpufreq can lower the frequency
to 1200 MHz on half the CPUs and do nothing on the others. With this
patchset, all CPUs can be lowered to 1200 MHz on a rev2 p4080, and on a
rev3 p4080 half can be lowered to 750 MHz and the other half to 600
MHz.
The current binding only deals with CPU clocks. To describe FMan in
the device tree, we need to describe its clock. Some chips have
additional muxes that work like the CPU muxes, but are not described in
the device tree. Others require inspecting the Reset Control Word to
determine which PLL is used. Rather than continue to extend this mess,
replace it. Have the driver bind to the chip-specific clockgen
compatible, and keep the detailed description of quirky chip variations
in the driver, where it can be easily fixed, refactored, and extended.
Older device trees will continue to work (including a workaround for
old ls1021a device trees that are missing compatible and reg in the
clockgen node, which even the old binding required). The pll/mux
details in old device trees will be ignored, but "clocks" properties
pointing at the old nodes will still work, and be directed at the
corresponding new clock.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
The module 1 type of clocks consist of a gate and a mux and are used on
the audio blocks to mux and gate the PLL2 outputs for AC97, IIS or
SPDIF. This commit adds support for them on the sunxi clock driver.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
The codec clock on sun4i, sun5i and sun7i is a simple gate with PLL2 as
parent. Add a driver for such a clock.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
The A13, unlike the A10 and A20, doesn't use a pass-through exception for
the 0 value in the pre and post dividers, but increments all the values
written in the register by one.
Add an exception for both these cases to handle them nicely.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
The PLL2 on the A10 and later SoCs is the clock used for all the audio
related operations.
This clock has a somewhat complex output tree, with three outputs (2X, 4X
and 8X) with a fixed divider from the base clock, and an output (1X) with a
post divider.
However, we can simplify things since the 1X divider can be fixed, and we
end up by having a base clock not exposed to any device (or at least
directly, since the 4X output doesn't have any divider), and 4 fixed
divider clocks that will be exposed.
This clock seems to have been introduced, at least in this form, in the
revision B of the A10, but we don't have any information on the clock used
on the revision A.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Some clocks are using a multiplier component, however, unlike their mux,
gate or divider counterpart, these factors don't have a basic clock
implementation.
This leads to code duplication across platforms that want to use that kind
of clocks, and the impossibility to use the composite clocks with such a
clock without defining your own rate operations.
Create such a driver in order to remove these issues, and hopefully factor
the implementations, reducing code size across platforms and consolidating
the various implementations.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
This patch affects the clocks that use fractional ndivider in their
PLL output frequency calculation. Instead of 2^20 divide factor, the
clock's ndiv integer shift was used. Fixed the bug by replacing ndiv
integer shift with 2^20 factor.
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Fixes: 5fe225c105 ("clk: iproc: add initial common clock support")
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The clocks' properties have been already properly set, so there's no
need to set this flag for sdio0 and sdio1 clk any more.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Since we have added the necessary two clks' properties in dts, we can
remove the "sdio" clk's CLK_IGNORE_UNUSED flag now.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
clk_add_alias() was not correctly handling the case where alias_dev_name
was NULL: rather than producing an entry with a NULL dev_id pointer,
it would produce a device name of (null). Fix this.
Cc: <stable@vger.kernel.org>
Fixes: 2568999835 ("clkdev: add clkdev_create() helper")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This contains a patch that allows the DFLL to use clock rates higher
than 2^31-1 Hz by using the ->determine_rate() operation instead of the
->round_rate() operation. Other than that there's a couple of cleanups
in preparation for Tegra210 support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4qKy
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.4-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.4-rc1
This contains a patch that allows the DFLL to use clock rates higher
than 2^31-1 Hz by using the ->determine_rate() operation instead of the
->round_rate() operation. Other than that there's a couple of cleanups
in preparation for Tegra210 support.
tegra_audio_clk_init was written expecting a single PLL to be
passed in directly. Change this to accept an array which will
allow for supporting multiple plls and specifying specific data
about them, like their parent, which may change over time.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Benson Leung pointed out that the kerneldoc for this structure has
become stale. Update the field descriptions to match the structure
content.
Reported-by: Benson Leung <bleung@chromium.org>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some fields moved from the tegra_clk_pll struct to the tegra_pll_params
struct. Update the struct comments to reflect where the fields really
are.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The monitor code is used with DEBUG_FS only, so move it into the
corresponding #ifdef block to avoid potential compiler warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The R8 is a new Allwinner SoC based on the A13. While both are very
similar, there's still a few differences. Introduce a new compatible to
deal with them.
In order to have a consistent naming, instead of mentioning the Allwinner
A series as the machine name, switch to sun4i/sun5i like what is done for
the other families.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
This reverts commit e79b202c63.
Now that we use of_clk_get() inside of_clk_get_parent_name() we
can safely use it here.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add rcg and branch clk structs for DSI1 and DSI2 blocks found in MSM8960
and APQ8064. Each DSI instance has 4 pairs of rcg and branch clocks.
Populate arrays mmcc_msm8960_clks and mmcc_apq8064_clks with these clocks.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
DSI specific RCG clocks required customized clk_ops. There are
a total of 4 RCGs per DSI block: DSI, BYTE, ESC and PIXEL.
There are a total of 2 clocks coming from the DSI PLL, which serve as
inputs to these RCGs. The BYTE and ESC RCGs are fed by one of the
post dividers of DSI1 or DSI2 PLLs, and the DSI and PIXEL RCGs are fed by
another divider of the PLL.
In each of the 2 groups above, only one of the clocks sets its parent.
These are BYTE RCG and DSI RCG for each of the groups respectively, as
shown in the diagram below.
The DSI and BYTE RCGs serve as bypass clocks. We create a new set of ops
clk_rcg_bypass2_ops, which are like the regular bypass ops, but don't
take in a freq table, since the DSI driver using these clocks is
parent-able.
The PIXEL RCG needs to derive the required pixel clock using dsixpll.
It parses a m/n frac table to retrieve the correct clock.
The ESC RCG doesn't have a frac M/N block, it can just apply a pre-
divider. Its ops simply check if the required clock rate can be
achieved by the pre-divider.
+-------------------+
| |---dsixpllbyte---o---> To byte RCG
| | | (sets parent rate)
| | |
| | |
| DSI 1/2 PLL | |
| | o---> To esc RCG
| | (doesn't set parent rate)
| |
| |----dsixpll-----o---> To dsi RCG
+-------------------+ | (sets parent rate)
( x = 1, 2 ) |
|
o---> To pixel rcg
(doesn't set parent rate)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These drivers only have runtime but no build time dependencies so can be
built for testing purposes if the Kconfig COMPILE_TEST option is enabled.
This is useful to have more build coverage and make sure that drivers are
not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When calling __clk_get_name() on a const clock:
warning: passing argument 1 of '__clk_get_name' discards 'const' qualifier from pointer target type
include/linux/clk-provider.h:613:13: note: expected 'struct clk *' but argument is of type 'const struct clk *'
__clk_get_name() does not modify the passed clock, hence make it const.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
r8a7778_rates[] and r8a7778_divs[] are only used in clk-r8a7778.c, and
never modified.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- A couple of fixes on i.MX31 and i.MX35 clock initialization functions
which makes mxc_timer_init() currently be called twice for DT boot.
- Increase i.MX6UL AXI bus clock rate to 264MHz which is the optimal
design target.
- Add a few missing clocks, ADC clock for i.MX7D, OCOTP clock for
Vybrid, and SPDIF_GCLK for i.MX6.
- A series from Lucas to fix early debug UART clock setup. This is
currently a one-off fix for i.MX platform, and can be extended to
become a generic solution later.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWIRFyAAoJEFBXWFqHsHzOE7wH/25WaamOOOL3vGVCBeIs2+aB
nibCEKCPGu2/b1YN+BEQMlh+K7d59Ogd0xVtTkLEGhIBW+LF5zDpsd6jNl7Ts6PQ
5w3gG7K/NqPzIXlgo+z5Oa4UI1DlDemcA1xihR+hFWjLQb8DBmnusK52ctS5MLfP
6SoepDWHJvtuAfoL/3ytNTi/xCW12sEVkzRV7QbG9GV2UmUgF2AVWKBkH+c28vnP
dyt2Cyrr4+9ov6p0k0OJnHDv1AxkkNlHh0G33pZMZmnqcn/ZagmdH2GReGWZi6PM
XLMY/piEK7zzryJ51hL9AGZi7so1LWs27kBtYo9r7bN9/cG4kaENGw6Du1jEf4I=
=OBCO
-----END PGP SIGNATURE-----
Merge tag 'imx-clk-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-next
Pull i.MX updates from Shawn Guo:
"The i.MX clock updates for 4.4:
- A couple of fixes on i.MX31 and i.MX35 clock initialization functions
which makes mxc_timer_init() currently be called twice for DT boot.
- Increase i.MX6UL AXI bus clock rate to 264MHz which is the optimal
design target.
- Add a few missing clocks, ADC clock for i.MX7D, OCOTP clock for
Vybrid, and SPDIF_GCLK for i.MX6.
- A series from Lucas to fix early debug UART clock setup. This is
currently a one-off fix for i.MX platform, and can be extended to
become a generic solution later."
* tag 'imx-clk-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx6: Add SPDIF_GCLK clock in clock tree
clk: imx7d: add ADC root clock
clk: imx31: Do not call mxc_timer_init twice when booting with DT
clk: imx7d: retain early UART clocks during kernel init
clk: imx6: retain early UART clocks during kernel init
clk: imx5: retain early UART clocks during kernel init
clk: imx35: retain early UART clocks during kernel init
clk: imx31: retain early UART clocks during kernel init
clk: imx27: retain early UART clocks during kernel init
clk: imx25: retain early UART clocks during kernel init
clk: imx: add common logic to detect early UART usage
clk: imx35: Do not call mxc_timer_init twice when booting with DT
clk: clk-vf610: Add clock for Vybrid OCOTP controller
clk: imx: increase AXI clock rate to 264MHz for i.MX6UL
If a clock provider has #clock-cells = 1 and we call
of_clk_get_parent_name() on it we may end up returning the name
of the provider node if the provider doesn't have a
clock-output-names property. This doesn't make sense, especially
when you consider that calling of_clk_get_parent_name() on such a
node with different indices will return the same name each time.
Let's try getting the clock from the framework via of_clk_get()
instead, and only fallback to the node name if we have a provider
with #clock-cells = 0. This way, we can't hand out the same name
for different clocks when we don't actually know their names.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add cpuclk in the Berlin BG2Q clock driver. This clk has a divider
fixed to 1.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The email address listed in MODULE_AUTHOR() no longer exist so to prevent
people to send emails to the old address, replace it with my current one.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This partially reverts commit eca61c9ff2.
Thomas reports that it causes regressions on Armada XP devices.
This is because of_clk_get_parent_name() relies on the property
'clock-output-names' to resolve the name of a clock's parent,
without trying to get the clock from the framework and call
__clk_get_name(). Given that Armada XP devices don't have the
'clock-output-names' property, of_clk_get_parent_name() returns
the name of the node which doesn't match the actual parent
clock's name at all, causing CPU clocks to never link up with
their parents.
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9u+p
-----END PGP SIGNATURE-----
Merge tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
Merge "ARM System Control and Power Interface(SCPI) support" from Sudeep Holla
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
* tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
hwmon: Support thermal zones registration for SCP temperature sensors
hwmon: Support sensors exported via ARM SCP interface
firmware: arm_scpi: Extend to support sensors
Documentation: add DT bindings for ARM SCPI sensors
cpufreq: arm_big_little: add SCPI interface driver
clk: scpi: add support for cpufreq virtual device
clk: add support for clocks provided by SCP(System Control Processor)
firmware: add support for ARM System Control and Power Interface(SCPI) protocol
Documentation: add DT binding for ARM System Control and Power Interface(SCPI) protocol
for_each_child_of_node performs an of_node_put on each iteration, so
putting an of_node_put before a continue results in a double put.
The semantic match that finds this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
iterator name for_each_child_of_node;
@@
for_each_child_of_node(root, child) {
... when != of_node_get(child)
* of_node_put(child);
...
* continue;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* clk-bcm2835:
clk: bcm2835: Add support for programming the audio domain clocks
clk: bcm2835: Add binding docs for the new platform clock driver.
clk: bcm2835: Move under bcm/ with other Broadcom SoC clk drivers.
This adds support for enabling, disabling, and setting the rate of the
audio domain clocks. It will be necessary for setting the pixel clock
for HDMI in the VC4 driver and let us write a cpufreq driver. It will
also improve compatibility with user changes to the firmware's
config.txt, since our previous fixed clocks are unaware of it.
The firmware also has support for configuring the clocks through the
mailbox channel, but the pixel clock setup by the firmware doesn't
work, and it's Raspberry Pi specific anyway. The only conflicts we
should have with the firmware would be if we made firmware calls that
result in clock management (like opening firmware V3D or ISP access,
which we don't support in upstream), or on hardware over-thermal or
under-voltage (when the firmware would rewrite PLLB to take the ARM
out of overclock). If that happens, our cached .recalc_rate() results
would be incorrect, but that's no worse than our current state where
we used fixed clocks.
The existing fixed clocks in the code are left in place to provide
backwards compatibility with old device tree files.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Correct SPDIF clock setting issue in clock tree, the SPDIF_GCLK is also
one clock of SPDIF, which is missed before.
We found an issue that imx can't enter low power mode with spdif
if IMX6x_CLK_SPDIF is used as the core clock of spdif. Because
spdif driver will register IMX6x_CLK_SPDIF clock to regmap, regmap will do
clk_prepare in init function, then IMX6x_CLK_SPDIF clock is prepared in probe,
so its parent clock (PLL clock) is prepared, the prepare operation of
PLL clock is to enable the clock. But I.MX needs all PLL clock is disabled,
then it can enter low power mode.
So we can't use IMX6x_CLK_SPDIF as the core clock of spdif, the correct spdif
core clock is SPDIF_GCLK, which share same gate bit with IMX6x_CLK_SPDIF clock.
SPDIF_GCLK's parent clock is ipg clock.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
8960 family of devices have TSENS as part of GCC in hardware.
Hence DT would represent a GCC node with GCC properties as well
as TSENS. Create a virtual platform child device here for TSENS
so the driver can probe it and use the parent (GCC) to extract DT
properties.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[sboyd@codeaurora.org: Massaged to work with devm friendly
qcom_cc_probe()]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Having this hidden config below the COMMON_CLK_QCOM config causes
menuconfig to stop indenting config items after it.
<*> Support for Qualcomm's clock controllers
{M} APQ8084 Global Clock Controller
<M> APQ8084 Multimedia Clock Controller
{M} IPQ806x Global Clock Controller
<M> IPQ806x LPASS Clock Controller
<M> MSM8660 Global Clock Controller
<M> MSM8916 Global Clock Controller
{M} APQ8064/MSM8960 Global Clock Controller
<M> APQ8064/MSM8960 LPASS Clock Controller
<M> MSM8960 Multimedia Clock Controller
{M} MSM8974 Global Clock Controller
<M> MSM8974 Multimedia Clock Controller
Move it up above anything else so that we don't get odd
indenting.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that qcom_cc_remove() is a nop, drop calls to
qcom_cc_remove() and any empty driver remove functions.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some APIs in qcom_cc_probe() don't have a devm counterpart, so we
have to use the calling device's platform data to pass pointers
to the remove path. Let's use devm_add_action() instead, so that
the remove path doesn't need to do anything, allowing us to
remove qcom_cc_remove() entirely.
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for new PLL-type for stih418 A9-PLL.
Currently the 407_A9_PLL type being used, it is corrected with this patch
4600c28 PLL allows to reach higher frequencies
so its programming algorithm is extended.
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Change A9 PLL rate, as per requirement from the cpufreq framework,
for DVFS. For rate change, the A9 clock needs to be temporarily sourced
from PLL external to A9 and then sourced back to A9-PLL
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The patch adds support for enable/disable of the Clockgen PLLs.
clkgen_pll_enable/clkgen_pll_disable added as generic function for all PLLs.
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The oxili_cx GDSC is inside the power domain of the oxili GDSC.
Add the dependency so that the CX domain can properly power up.
Reported-by: Rob Clark <robdclark@gmail.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds the driver and devicetree documentation for the
Silicon Labs SI514 clock generator chip. This is an I2C controlled
oscillator capable of generating clock signals ranging from 100kHz
to 250MHz.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
[sboyd@codeaurora.org: Drop clk.h include, remove some casts]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* Consider "zb_clk" suitable for power management
This part of a multi-stage effort by Geert Uytterhoeven to add:
"Clock Domain support to the Clock Pulse Generator (CPG) Module Stop
(MSTP) Clocks driver using the generic PM Domain, to be used on shmobile
SoCs without device power domains (R-Car Gen1 and Gen2, RZ). This allows
to power-manage the module clocks of SoC devices that are part of the
CPG/MSTP Clock Domain using Runtime PM, or for system suspend/resume,
similar to SoCs with device power domains (SH-Mobile and R-Mobile)."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lwZa
-----END PGP SIGNATURE-----
Merge tag 'renesas-clk-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
Merge "Renesas ARM Based SoC Clk Updates for v4.4" from Simon Horman:
* Consider "zb_clk" suitable for power management
This part of a multi-stage effort by Geert Uytterhoeven to add:
"Clock Domain support to the Clock Pulse Generator (CPG) Module Stop
(MSTP) Clocks driver using the generic PM Domain, to be used on shmobile
SoCs without device power domains (R-Car Gen1 and Gen2, RZ). This allows
to power-manage the module clocks of SoC devices that are part of the
CPG/MSTP Clock Domain using Runtime PM, or for system suspend/resume,
similar to SoCs with device power domains (SH-Mobile and R-Mobile)."
* tag 'renesas-clk-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
clk: shmobile: mstp: Consider "zb_clk" suitable for power management
* ARM: shmobile: R-Mobile: Use CPG/MSTP Clock Domain attach/detach helpers
This part of a multi-stage effort by Geert Uytterhoeven to add:
"Clock Domain support to the Clock Pulse Generator (CPG) Module Stop
(MSTP) Clocks driver using the generic PM Domain, to be used on shmobile
SoCs without device power domains (R-Car Gen1 and Gen2, RZ). This allows
to power-manage the module clocks of SoC devices that are part of the
CPG/MSTP Clock Domain using Runtime PM, or for system suspend/resume,
similar to SoCs with device power domains (SH-Mobile and R-Mobile)."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OvKg
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Renesas ARM Based SoC Updates for v4.4" from Simon Horman:
* ARM: shmobile: R-Mobile: Use CPG/MSTP Clock Domain attach/detach helpers
This part of a multi-stage effort by Geert Uytterhoeven to add:
"Clock Domain support to the Clock Pulse Generator (CPG) Module Stop
(MSTP) Clocks driver using the generic PM Domain, to be used on shmobile
SoCs without device power domains (R-Car Gen1 and Gen2, RZ). This allows
to power-manage the module clocks of SoC devices that are part of the
CPG/MSTP Clock Domain using Runtime PM, or for system suspend/resume,
similar to SoCs with device power domains (SH-Mobile and R-Mobile)."
* tag 'renesas-soc-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: R-Mobile: Use CPG/MSTP Clock Domain attach/detach helpers
clk: shmobile: mstp: Consider "zb_clk" suitable for power management
Pull mediatek clock support and fixes from James Liao:
"This is a collection of new Mediatek clocks support and fixes.
These patches come from Joe and me, including clock support for
subsystems, GPT and some minor fixes."
* 'v4.3-rc3-clk' of https://github.com/jamesjjliao/linux:
clk: mediatek: Add USB clock support in MT8173 APMIXEDSYS
clk: mediatek: Add subsystem clocks of MT8173
dt-bindings: ARM: Mediatek: Document devicetree bindings for clock controllers
clk: mediatek: Fix rate and dependency of MT8173 clocks
clk: mediatek: Add fixed clocks support for Mediatek SoC.
clk: mediatek: Add __initdata and __init for data and functions
clk: mediatek: Remove unused code from MT8173.
clk: mediatek: Removed unused dpi_ck clock from MT8173
clk: mediatek: add 13mhz clock for MT8173
drivers/clk/samsung/clk-exynos7.c:896:33:
warning: symbol 'fixed_rate_clks_fsys0' was not declared. Should
it be static?
drivers/clk/samsung/clk-exynos7.c:1010:33:
warning: symbol 'fixed_rate_clks_fsys1' was not declared. Should
it be static?
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch converts the code to use rational best approximation algorithm which
is much more precise.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The ->mwidth and ->nwidth fields will be used by clk-fractional-divider when it
will be switched to rational base approximation algorithm.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The patch adds mwidth and nwidth fields to the struct clk_fractional_divider
for further usage. While here, use GENMASK() instead of open coding this
functionality.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Rename function parameter to be more explicit what it is for. This also makes
it in align with struct clk_ops.
There is no functional change.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The default clock enabling functions for TI clocks -
omap2_dflt_clk_enable() and omap2_dflt_clk_disable() perform a
NULL check for the enable_reg field of the clk_hw_omap structure.
This enable_reg field however is merely a combination of the index
of the master IP module, and the offset from the master IP module's
base address. A value of 0 is perfectly valid, and the current error
checking will fail in these cases. The issue was found when trying
to enable the iva2_ck clock on OMAP3 platforms.
So, switch the check to use IS_ERR. This correction is similar to the
logic used in commit c807dbedb5 ("clk: ti: fix ti_clk_get_reg_addr
error handling").
Fixes: 9f37e90efa ("clk: ti: dflt: move support for default gate clock..")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
On the OMAP AM3517 platform the uart4_ick gets registered
twice, causing any power management to /dev/ttyO3 to fail
when trying to wake the device up.
This solves the following oops:
[] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa09e008
[] PC is at serial_omap_pm+0x48/0x15c
[] LR is at _raw_spin_unlock_irqrestore+0x30/0x5c
Fixes: aafd900cab ("CLK: TI: add omap3 clock init file")
Cc: stable@vger.kernel.org
Cc: mturquette@baylibre.com
Cc: sboyd@codeaurora.org
Cc: linux-clk@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-kernel@lists.codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The ABE related clocks should be configured via DT and not have it wired
inside of the kernel.
Fixes: a74c52def9 ("clk: ti: clk-7xx: Correct ABE DPLL configuration")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
clk-bcm2835.c predates the drivers under bcm/, but all the new BCM
drivers are going in there so let's follow them.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This simplifies the given function by getting rid of the manual
sign extension as well as saving an absolute value in an extra
variable.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
mmc host controller's IO input/output timing is unpredictable if
bootloader execute tuning for HS200 mode. It might make kernel failed
to initialize mmc card in identification mode. The root cause is
tuning phase and degree setting for HS200 mode in bootloader aren't
applicable to that of identification mode in kernel stage. Anyway, we
can't force all bootloaders to reset tuning phase and degree setting
before into kernel. Simply reset it in rockchip_clk_register_mmc.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On drivers/clk/mxs/clk-frac.c, the function clk_frac_round_rate returned a bad
result. The division before multiplication computes a wrong value ; the
calculation is inverted to fix the problem. The second issue is that the exact
rate have decimals and they are truncate. The consequence is that the function
clk_frac_set_rate (which use the result of clk_frac_round_rate) computes a
wrong value for the register (the rate generated can be closer to the desired
rate). The correction is : if there is decimal to the result, it is rounded to
the next larger integer.
On drivers/clk/mxs/clk-frac.c, the function clk_frac_recalc_rate returned
a bad result. The multiplication is made before the division to compute a
correct value.
Signed-off-by: Victorien Vedrine <victorien.vedrine@ophrys.net>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Separate the update of pll registers from the actual set_rate function
so that the init callback does not need to access clk-API functions.
As we now have separated the getting and setting of the pll parameters
we can also directly use these new functions in other places too.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a new type of clocks that can be provided to a peripheral.
In addition to the peripheral clock, this new clock that can use several
input clocks as parents can generate divided rates.
This would allow a peripheral to have finer grained clocks for generating
a baud rate, clocking an asynchronous part or having more
options in frequency.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[sboyd@codeaurora.org: Transition to new clk_hw provider APIs]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the new sama5d2 SoC and adapt capabilities.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
As some more information is added to the PCR register, we'd better use
a copy of its content and modify just the peripheral-related bits.
Implement a read-modify-write for the enable() and disable() callbacks.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add _MASK and _OFFSET values and cleanup register fields layout.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add REF2USB_TX clock support into MT8173 APMIXEDSYS. This clock
is needed by USB 3.0.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Most multimedia subsystem clocks will be accessed by multiple
drivers, so it's a better way to manage these clocks in CCF.
This patch adds clock support for MM, IMG, VDEC, VENC and VENC_LT
subsystems.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Remove the dependency from clk_null, and give all root clocks a
typical rate, include clkph_mck_o, usb_syspll_125m and hdmitx_dig_cts.
dpi_ck was removed due to no clock reference to it.
Replace parent clock of infra_cpum with cpum_ck, which is an external
clock and can be defined in the device tree.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
This patch adds fixed clocks support by using CCF fixed-rate
clock implementation.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Add __init for clock registration functions, and add __initdata for
mtk_gate_regs initial structures.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Remove unused header files from MT8173, and remove unused
keywords from function declaration.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
The dpi_ck clock can be removed because it not actually used
in topckgen and subsystems.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Add 13mhz clock used by GPT timer in infracfg.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
mxc_timer_init must not be called from within mx31_clocks_init_dt. It will
eventually be called by imx31_timer_init_dt
(drivers/clocksource/timer-imx-gpt.c).
This arranges the initialization code similar to clk-imx27.c
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Power management on of NoC(Notwork On Chip) requires that disconnect
and reconnect routine should been done during clk disable/enable.
also there are different types of clocks,
For NoC Macro clocks, write idle_bit and wait for hardward ACK;
For Socket clocks, write idle_bit;
For others, do nothing.
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
re-order the codes more reasonable by moving variable-definition
together.
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The clocks for the CPUs are provided by SCP and are managed by this
clock driver. So the cpufreq device needs to be added only after the
clock get registered and removed when this driver is unloaded.
This patch manages the cpufreq virtual device based on the clock
availability.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@baylibre.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jon Medhurst (Tixy) <tixy@linaro.org>
Cc: linux-clk@vger.kernel.org
On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control. System Control and Power Interface(SCPI) Message Protocol
is defined for the communication between the Application Cores(AP)
and the SCP.
This patch adds support for the clocks provided by SCP using SCPI
protocol.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@baylibre.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jon Medhurst (Tixy) <tixy@linaro.org>
Cc: linux-clk@vger.kernel.org
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Both earlycon and eralyprintk depend on the bootloader setup UART
clocks being retained. This patch adds the common logic to detect such
situations and make the information available to the clock drivers, as
well as adding the facilities to disable those clocks at the end of
the kernel init.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mxc_timer_init must not be called from within mx35_clocks_init_dt. It will
eventually be called by imx31_timer_init_dt
(drivers/clocksource/timer-imx-gpt.c).
This arranges the initialization code similar to clk-imx27.c
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add clock support for Vybrid On-Chip One Time Programmable
(OCOTP) controller.
While the OCOTP block does not require explicit clock gating,
for programming the OCOTP timing register the clock rate of
ipg clock is required for timing calculations related to fuse
and shadow register read sequence. We explicitly specify the
ipg clock for OCOTP as a result.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
CLK_CPU_HAS_DIV1 and CLK_CPU_NEEDS_DEBUG_ALT_DIV masks were
incorrectly used as a bit numbers. Fix it.
Tested on Exynos4210 based Origen board and on Exynos5250 based
Arndale board.
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Fixes: ddeac8d96 ("clk: samsung: add infrastructure to register cpu clocks")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
in the framework to avoid oops when get_parent ops return out of range
values on tegra platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LSuc
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A few driver fixes for tegra, rockchip, and st SoCs and a two-liner in
the framework to avoid oops when get_parent ops return out of range
values on tegra platforms"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
drivers: clk: st: Rename st_pll3200c32_407_c0_x into st_pll3200c32_cx_x
clk: check for invalid parent index of orphans in __clk_init()
clk: tegra: dfll: Properly protect OPP list
clk: rockchip: add critical clock for rk3368
The A33 gates are different from the A23 ones, add a new hook to simple
gates to handle this clock
Reported-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently the CPG/MSTP Clock Domain code looks for MSTP clocks to power
manage a device.
Unfortunately, on R-Mobile APE6 (r8a73a4) and SH-Mobile AG5 (sh73a0),
the Bus State Controller (BSC) is not power-managed by an MSTP clock,
but by a plain CPG clock (zb_clk). Add a special case to handle this,
so the clock is properly managed, and devices connected to the BSC work
as expected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the msm8916 audio clocks. This includes core bus,
low-power audio and codec clocks. They are required for audio playback.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the msm8916 BIMC (Bus Integrated Memory Controller)
clocks that are needed for GPU.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some root clock generators may have child branches that are controlled
by different CPUs. These RCGs require some special operations:
- some enable bits have to be toggled when we set the rate;
- if RCG is disabled we only cache the rate and set it later when enabled;
- when the RCG is disabled, the mux is set to the safe source;
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
[sboyd@codeaurora.org: Simplify recalc_rate implementation]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the msm8916 TCU (Translation Control Unit) clocks that
are needed for IOMMU.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use a generic name for this kind of PLL
Correction in dts files are already done here:
commit 5eb26c6059 ("ARM: STi: DT: Rename st_pll3200c32_407_c0_x into st_pll3200c32_cx_x")
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There are cleary typo errors so can be removed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On i.MX6UL, AXI clock rate's design target is 264MHz, but by default
it is only set to 198MHz which is NOT good enough for performance,
this patch increases AXI clock rate from 198MHz to 264MHz to meet
the design target, this is done by switching its parent clock
"periph" from 396MHz PFD to 528MHz PLL.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
If a mux clock is initialised (by hardware or firmware) with an
invalid parent, its ->get_parent() can return an out of range
index. For example, the generic mux clock attempts to return
-EINVAL, which due to the u8 return type ends up a rather large
number. Using this index with the parent_names[] array results
in an invalid pointer and (usually) a crash in the following
strcmp().
This patch adds a check for the parent index being in range,
ignoring clocks reporting invalid values.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Tested-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the GDSC instances that exist as part of apq8084 MMCC block.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the GDSC instances that exist as part of apq8084 GCC block
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the GDSC instances that exist as part of msm8974 MMCC block
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There's just one GDSC as part of the msm8974 GCC block.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add all data for the GDSCs which are part of msm8916 GCC block.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Certain devices can have GDSCs' which support ON as the only state.
They can't be power collapsed to either hit RET or OFF.
The clients drivers for these GDSCs' however would expect the state
of the core to be reset following a GDSC disable and re-enable.
To do this assert/deassert reset lines every time the client
driver would request the GDSC to be powered on/off instead.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Along with the GDSC power switch, there is additional control
to either retain all memory (core and peripheral) within a given
powerdomain or to turn them off while the GDSC is powered down.
Add support for these by modelling a RET state where all
memory is retained and an OFF state where all memory gets turned
off.
The controls provided are granular enough to be able to support
various differnt levels of RET states, like a 'shallow RET' with all memory
retained and a 'deep RET' with some memory retained while some others
are lost. The current patch does not support this and considers
just one RET state where all memory is retained. Futher work, if
needed can support multiple different levels of RET state.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The common clk probe registers a clk provider and a reset controller.
Update it to register a genpd provider using the gdsc data provided
by each platform.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
GDSCs (Global Distributed Switch Controllers) are responsible for
safely collapsing and restoring power to peripherals in the SoC.
These are best modelled as power domains using genpd and given
the registers are scattered throughout the clock controller register
space, its best to have the support added through the clock driver.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On 32-bit architectures, 'unsigned long' (the type used to hold clock
rates, in Hz) is often only 32 bits wide. DIV_ROUND_UP() (as used in,
e.g., commit b11d282dbe "clk: divider: fix rate calculation for
fractional rates") can yield an integer overflow on clock rates that are
not (by themselves) too large to fit in 32 bits, because it performs
addition before the division. See for example:
DIV_ROUND_UP(3000000000, 1500000000) = (3.0G + 1.5G - 1) / 1.5G
= OVERFLOW / 1.5G
This patch fixes such cases by always promoting the dividend to 64-bits
(unsigned long long) before doing the division. While this patch does
not resolve the issue with large clock rates across the common clock
framework nor address the problems with doing full 64-bit arithmetic on
a 32-bit architecture, it does fix some issues seen when using clock
dividers on a 3GHz reference clock to produce a 1.5GHz CPU clock for an
ARMv7 Brahma B15 SoC.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reference: http://lkml.kernel.org/g/20150413201433.GQ32500@ld-irv-0074
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In the error path of at91_clk_register_system(), sys->irq is freed
unconditionally but it may not exist or be request at all.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
at91_pmc_read is a workaround to allow external drivers to acces some
registers of the PMC. There is no need for it in clk-utmi.c as we aready
have a pointer to the struct at91_pmc.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sometimes the display driver may want to change the parent PLL of
the display clocks (byte and pixel clocks) depending on the
use-case. Currently the parent is fixed by means of having a
frequency table with one entry that chooses a particular parent.
Remove this restriction and use the parent the clock is
configured for in the hardware during clk_set_rate(). This
requires consumers to rely on the default parent or to configure
the parent with clk_set_parent()/assigned-clock-parents on the
clocks before calling clk_set_rate().
Tested-by: Archit Taneja <architt@codeaurora.org>
Cc: Hai Li <hali@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The OPP list needs to be protected against concurrent accesses. Using
simple RCU read locks does the trick and gets rid of the following
lockdep warning:
===============================
[ INFO: suspicious RCU usage. ]
4.2.0-next-20150908 #1 Not tainted
-------------------------------
drivers/base/power/opp.c:460 Missing rcu_read_lock() or dev_opp_list_lock protection!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
4 locks held by kworker/u8:0/6:
#0: ("%s""deferwq"){++++.+}, at: [<c0040d8c>] process_one_work+0x118/0x4bc
#1: (deferred_probe_work){+.+.+.}, at: [<c0040d8c>] process_one_work+0x118/0x4bc
#2: (&dev->mutex){......}, at: [<c03b8194>] __device_attach+0x20/0x118
#3: (prepare_lock){+.+...}, at: [<c054bc08>] clk_prepare_lock+0x10/0xf8
stack backtrace:
CPU: 2 PID: 6 Comm: kworker/u8:0 Not tainted 4.2.0-next-20150908 #1
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
Workqueue: deferwq deferred_probe_work_func
[<c001802c>] (unwind_backtrace) from [<c00135a4>] (show_stack+0x10/0x14)
[<c00135a4>] (show_stack) from [<c02a8418>] (dump_stack+0x94/0xd4)
[<c02a8418>] (dump_stack) from [<c03c6f6c>] (dev_pm_opp_find_freq_ceil+0x108/0x114)
[<c03c6f6c>] (dev_pm_opp_find_freq_ceil) from [<c0551a3c>] (dfll_calculate_rate_request+0xb8/0x170)
[<c0551a3c>] (dfll_calculate_rate_request) from [<c0551b10>] (dfll_clk_round_rate+0x1c/0x2c)
[<c0551b10>] (dfll_clk_round_rate) from [<c054de2c>] (clk_calc_new_rates+0x1b8/0x228)
[<c054de2c>] (clk_calc_new_rates) from [<c054e44c>] (clk_core_set_rate_nolock+0x44/0xac)
[<c054e44c>] (clk_core_set_rate_nolock) from [<c054e4d8>] (clk_set_rate+0x24/0x34)
[<c054e4d8>] (clk_set_rate) from [<c0512460>] (tegra124_cpufreq_probe+0x120/0x230)
[<c0512460>] (tegra124_cpufreq_probe) from [<c03b9cbc>] (platform_drv_probe+0x44/0xac)
[<c03b9cbc>] (platform_drv_probe) from [<c03b84c8>] (driver_probe_device+0x218/0x304)
[<c03b84c8>] (driver_probe_device) from [<c03b69b0>] (bus_for_each_drv+0x60/0x94)
[<c03b69b0>] (bus_for_each_drv) from [<c03b8228>] (__device_attach+0xb4/0x118)
ata1: SATA link down (SStatus 0 SControl 300)
[<c03b8228>] (__device_attach) from [<c03b77c8>] (bus_probe_device+0x88/0x90)
[<c03b77c8>] (bus_probe_device) from [<c03b7be8>] (deferred_probe_work_func+0x58/0x8c)
[<c03b7be8>] (deferred_probe_work_func) from [<c0040dfc>] (process_one_work+0x188/0x4bc)
[<c0040dfc>] (process_one_work) from [<c004117c>] (worker_thread+0x4c/0x4f4)
[<c004117c>] (worker_thread) from [<c0047230>] (kthread+0xe4/0xf8)
[<c0047230>] (kthread) from [<c000f7d0>] (ret_from_fork+0x14/0x24)
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fixes: c4fe70ada4 ("clk: tegra: Add closed loop support for the DFLL")
[vince.h@nvidia.com: Unlock rcu on error path]
Signed-off-by: Vince Hsu <vince.h@nvidia.com>
[sboyd@codeaurora.org: Dropped second hunk that nested the rcu
read lock unnecessarily]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The new determine_rate prototype allows for clock rates exceeding
2^31-1 Hz to be used. Switch the DFLL clock to use determine_rate
instead of round_rate and unlock the top rates supported by the
Tegra124.
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Signed-off-by: Thierry Reding <treding@nvidia.com>
FSYS0 fixed clocks are not added to fsys0_cmu_info, this makes
some of the usb clocks orphans. This fixes the same.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch renames CMU_FSYS1 clocks names to match with user manual.
And also adds missing gate clock for aclk_fsys1_200.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch renames CMU_FSYS0 clocks names to match with user manual.
And also adds missing gate clock for aclk_fsys0_200.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch renames CMU_PERIS clocks names to match with user manual.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch renames CMU_PERIC1 clocks names to match with user manual.
And also adds missing gate clock for aclk_peric1_66.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch renames CMU_PERIC0 clocks names to match with user manual.
And also adds missing gate clock for aclk_peric0_66.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch renames CMU_CCORE clocks names to match with user manual.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch renames CMU_TOP1 clocks names to match with user manual.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch renames CMU_TOP0 clocks names to match with user manual.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This adds some of the missing GATE clocks of CMU_TOPC block.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Corrects the CMU_TOPC block clock names as per user manual.
This does not change any functionalities.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
nr_clk_ids for FSYS1 block is wrongly set as TOP1 block,
this patch corrects it.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch corrects the nr_clk_ids for fsys0 block
which is wrongly set to number of clocks of the TOP1 CMU.
This also adjusts the gate clocks order.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
As per UM, sclk_mmc2 is bit 16 of SEL_TOP1_FSYS0. Also the DIV
and the GATE clocks are at bit 16 in their respective registers.
For mmc1 and mmc0 clock MUXs are in TOP1_FSYS11 instead of TOP1_FSYS1.
And their DIV and GATE clks are in xxx_TOP1_FSYS11 instead of TOP1_FSYS1.
This patch corrects it.
This also adds xxx_FSYS11 to be saved/restore during s2r cycles.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Corrects the bit width of DIV_TOPC3 register.
These are wrongly set to 3 which should be 4 bit wide as per UM.
This also adjusts the MUX clock order.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
handful of patches to add more critical clocks on rockchip SoCs that
are affected by newly introduced gpio clock handling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Y9Y4
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A couple build fixes for drivers introduced in the merge window and a
handful of patches to add more critical clocks on rockchip SoCs that
are affected by newly introduced gpio clock handling"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: rockchip: Add pclk_peri to critical clocks on RK3066/RK3188
clk: rockchip: add pclk_cpu to the list of rk3188 critical clocks
clk: rockchip: handle critical clocks after registering all clocks
clk: Hi6220: separately build stub clock driver
clk: h8s2678: Fix compile error
Again a result of the gpio-clock-liberation the rk3368 needs the
pclk_pd_pmu marked as critical, to boot successfully.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This is a collection of a few late fixes and other misc. stuff that
had dependencies on things being merged from other trees.
The bulk of the changes are for samsung/exynos SoCs for some changes
that needed a few minor reworks so ended up a bit late. The others
are mainly for qcom SoCs: a couple fixes and some DTS updates.
There's one conflict with drivers/cpufreq/exynos-cpufreq.c because
it's now been completely removed, but there were some fixes that hit
mainline in the meantime.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=85Ck
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM SoC updates from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The bulk of the changes are for samsung/exynos SoCs for some changes
that needed a few minor reworks so ended up a bit late. The others
are mainly for qcom SoCs: a couple fixes and some DTS updates"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: multi_v7_defconfig: Enable PBIAS regulator
soc: qcom: smd: Correct fBLOCKREADINTR handling
soc: qcom: smd: Use correct remote processor ID
soc: qcom: smem: Fix errant private access
ARM: dts: qcom: msm8974-sony-xperia-honami: Use stdout-path
ARM: dts: qcom: msm8960-cdp: Use stdout-path
ARM: dts: qcom: msm8660-surf: Use stdout-path
ARM: dts: qcom: ipq8064-ap148: Use stdout-path
ARM: dts: qcom: apq8084-mtp: Use stdout-path
ARM: dts: qcom: apq8084-ifc6540: Use stdout-path
ARM: dts: qcom: apq8074-dragonboard: Use stdout-path
ARM: dts: qcom: apq8064-ifc6410: Use stdout-path
ARM: dts: qcom: apq8064-cm-qs600: Use stdout-path
ARM: dts: qcom: Label serial nodes for aliasing and stdout-path
reset: ath79: Fix missing spin_lock_init
reset: Add (devm_)reset_control_get stub functions
ARM: EXYNOS: switch to using generic cpufreq driver for exynos4x12
cpufreq: exynos: Remove unselectable rule for arm-exynos-cpufreq.o
ARM: dts: add iommu property to JPEG device for exynos4
ARM: dts: enable SPI1 for exynos4412-odroidu3
...
Now that the rockchip clock subsystem does clock gating with GPIO banks,
these are no longer enabled once during probe and no longer stay enabled
for eternity. When all these clocks are disabled, the parent clock pclk_peri
might be disabled too, as no other child claims it. So, we need to add pclk_peri
to the critical clocks.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Tested-by: Michael Niewoehner <linux@mniewoehner.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
pclk_cpu needs to keep running because it is needed for devices like
the act8865 regulator but with the recent gpio clock handling this is
not always the case anymore. So add it to the list of critical clocks.
Signed-off-by: Michael Niewoehner <linux@mniewoehner.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently the registration of critical clocks is done in the function
shared between rk3066 and rk3188 clock trees. That results in them
getting handled maybe before all of them are registered.
Therefore move the critical clock handling down to the end of the soc-
specific clock registration function, so that all clocks are registered
before they're maybe handled as critical clock.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Michael Niewoehner <linux@mniewoehner.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull i2c updates from Wolfram Sang:
"Features:
- new drivers: Renesas EMEV2, register based MUX, NXP LPC2xxx
- core: scans DT and assigns wakeup interrupts. no driver changes needed.
- core: some refcouting issues fixed and better API for that
- core: new helper function for best effort block read emulation
- slave framework: proper DT bindings and userspace instantiation
- some bigger work for xiic, pxa, omap drivers
.. and quite a number of smaller driver fixes, cleanups, improvements"
* 'i2c/for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (65 commits)
i2c: mux: reg Change ioread endianness for readback
i2c: mux: reg: fix compilation warnings
i2c: mux: reg: simplify register size checking
i2c: muxes: fix leaked i2c adapter device node references
i2c: allow specifying separate wakeup interrupt in device tree
of/irq: export of_get_irq_byname()
i2c: xgene-slimpro: dma_mapping_error() doesn't return an error code
i2c: Replace I2C_CROS_EC_TUNNEL dependency
eeprom: at24: use i2c_smbus_read_i2c_block_data_or_emulated
i2c: core: Add support for best effort block read emulation
i2c: lpc2k: add driver
i2c: mux: Add register-based mux i2c-mux-reg
i2c: dt: describe generic bindings
i2c: slave: print warning if slave flag not set
i2c: support 10 bit and slave addresses in sysfs 'new_device'
i2c: take address space into account when checking for used addresses
i2c: apply DT flags when probing
i2c: make address check indpendent from client struct
i2c: rename address check functions
i2c: apply address offset for slaves, too
...
cycle
Core changes:
- It is possible configure groups in debugfs.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx also wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
Driver feature enhancements:
- Power management support for the SiRF SoC Atlas 7.
- Power down support for the Qualcomm driver.
- Intel Cherryview and Baytrail: switch drivers to use raw
spinlocks in IRQ handlers to play nice with the realtime
patch set.
- Rework and new modes handling for Qualcomm SPMI-MPP.
- Pinconf power source config for SH PFC.
New drivers and subdrivers:
- A new driver for Conexant Digicolor CX92755.
- A new driver for UniPhier PH1-LD4, PH1-Pro4, PH1-sLD8,
PH1-Pro5, ProXtream2 and PH1-LD6b SoC pin control support.
- Reverse-egineered the S/PDIF settings for the Allwinner
sun4i driver.
- Support for Qualcomm Technologies QDF2xxx ARM64 SoCs
- A new Freescale i.mx6ul subdriver.
Cleanup:
- Remove platform data support in a number of SH PFC
subdrivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4QFX
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.3 development
cycle.
Like with GPIO it's a lot of stuff. If my subsystems are any sign of
the overall tempo of the kernel v4.3 will be a gigantic diff.
[ It looks like 4.3 is calmer than 4.2 in most other subsystems, but
we'll see - Linus ]
Core changes:
- It is possible configure groups in debugfs.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data(). This series was
created by Thomas Gleixner after the problem was observed by
Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx also wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
Driver feature enhancements:
- Power management support for the SiRF SoC Atlas 7.
- Power down support for the Qualcomm driver.
- Intel Cherryview and Baytrail: switch drivers to use raw spinlocks
in IRQ handlers to play nice with the realtime patch set.
- Rework and new modes handling for Qualcomm SPMI-MPP.
- Pinconf power source config for SH PFC.
New drivers and subdrivers:
- A new driver for Conexant Digicolor CX92755.
- A new driver for UniPhier PH1-LD4, PH1-Pro4, PH1-sLD8, PH1-Pro5,
ProXtream2 and PH1-LD6b SoC pin control support.
- Reverse-egineered the S/PDIF settings for the Allwinner sun4i
driver.
- Support for Qualcomm Technologies QDF2xxx ARM64 SoCs
- A new Freescale i.mx6ul subdriver.
Cleanup:
- Remove platform data support in a number of SH PFC subdrivers"
* tag 'pinctrl-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (95 commits)
pinctrl: at91: fix null pointer dereference
pinctrl: mediatek: Implement wake handler and suspend resume
pinctrl: mediatek: Fix multiple registration issue.
pinctrl: sh-pfc: r8a7794: add USB pin groups
pinctrl: at91: Use generic irq_{request,release}_resources()
pinctrl: cherryview: Use raw_spinlock for locking
pinctrl: baytrail: Use raw_spinlock for locking
pinctrl: imx6ul: Remove .owner field
pinctrl: zynq: Fix typos in smc0_nand_grp and smc0_nor_grp
pinctrl: sh-pfc: Implement pinconf power-source param for voltage switching
clk: rockchip: add pclk_pd_pmu to the list of rk3288 critical clocks
pinctrl: sun4i: add spdif to pin description.
pinctrl: atlas7: clear ugly branch statements for pull and drivestrength
pinctrl: baytrail: Serialize all register access
pinctrl: baytrail: Drop FSF mailing address
pinctrl: rockchip: only enable gpio clock when it setting
pinctrl/mediatek: fix spelling mistake in dev_err error message
pinctrl: cherryview: Serialize all register access
pinctrl: UniPhier: PH1-Pro5: add I2C ch6 pin-mux setting
pinctrl: nomadik: reflect current input value
...
The previous code, kernel builds Hi6220's common clock driver and stub
clock driver together. Stub clock driver has introduced the dependency
with CONFIG_MAILBOX, so kernel will not build Hi6220's common clock
driver due ARM64's defconfig have not enabled CONFIG_MAILBOX by default.
So separately build stub clock driver and common clock driver for
Hi6220; and only let stub clock driver has the dependency with
CONFIG_MAILBOX.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Recent cleanup removed some include files without checking if the cleaned
up code still compiles. This results in the following compile error.
drivers/clk/h8300/clk-h8s2678.c: In function ‘h8s2678_pll_clk_setup’:
drivers/clk/h8300/clk-h8s2678.c:99:14: error:
implicit declaration of function ‘kzalloc’
drivers/clk/h8300/clk-h8s2678.c:138:2: error:
implicit declaration of function ‘kfree’
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- Cleanups for Renesas shmobile platforms
- Lots of added devices on LPC18xx
- Lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some branches
that are primarily merged through the clock tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D2Pm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
Some releases this branch is nearly empty, others we have more stuff. It
tends to gather drivers that need SoC modification or dependencies such
that they have to (also) go in through our tree.
For this release, we have merged in part of the reset controller tree
(with handshake that the parts we have merged in will remain stable),
as well as dependencies on a few clock branches.
In general, new items here are:
- Qualcomm driver for SMM/SMD, which is how they communicate with the
coprocessors on (some) of their platforms
- Memory controller work for ARM's PL172 memory controller
- Reset drivers for various platforms
- PMU power domain support for Marvell platforms
- Tegra support for T132/T210 SoCs: PMC, fuse, memory controller per-SoC support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV5Ou9AAoJEIwa5zzehBx3/k4P/jA5CVNiDvIs0GoTR3uGOuec
MYd19oKf76reV1oL5bBSpg9uryJd3fPzK0JC/qU3pYfsCVFp2TWZD7liNpitqHyt
2xL02gzJQgjHzL3QrxTQrOFJDO6P8Vm2k/5pI0KX1beoulHvI+iHejNryXGjSKSx
9vbs1GPXU9IV831YOHSaMmHz727J65bbZE8Up113ctT+WbEIc1g/ihKzUgi/8xXW
RniMxGsX8HynE3VH+UBDMbY6XkOmzZa1Wabgll735MXwIUFG1+TsvHNuGehXUski
ySwqk67en25i0F/Q7oobLSZwCPbA6Ylxk9aOfr0AnAqOEKwgKWS+K7HkEiNMz7yh
nt22b5SVkQ80sTCbNEkdJajOZ8oRalUae19CGxvMfVh77LmQ2sRI9iJrwXcxkt8W
ASs6uDDAUNC5pIWfjeJE50vsDr//Hed/WtsIjenYOtb+RI1kru5iTTgp4oLPBiy5
OeHxOfiL7gPvyZQbuPgMKAGdoGBsa/7wTM7KWJCMP6mPGHpShO8XUUsuljqKHm4w
nBV7eZRMiIuWkjRKw4bjp7R0NVKR5sOfAkZhjCsXB0aqA/NU2zyNbViWcGCh6yj8
3beZ93SdEdrKX6N8pPiAhGTMFA6eev8YeUHO7kM4IhC91ILjHlPpCs1pYk3pwEkO
ABC7GyMY6Olg1pZJweEa
=B6jn
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some releases this branch is nearly empty, others we have more stuff.
It tends to gather drivers that need SoC modification or dependencies
such that they have to (also) go in through our tree.
For this release, we have merged in part of the reset controller tree
(with handshake that the parts we have merged in will remain stable),
as well as dependencies on a few clock branches.
In general, new items here are:
- Qualcomm driver for SMM/SMD, which is how they communicate with the
coprocessors on (some) of their platforms
- memory controller work for ARM's PL172 memory controller
- reset drivers for various platforms
- PMU power domain support for Marvell platforms
- Tegra support for T132/T210 SoCs: PMC, fuse, memory controller
per-SoC support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
ARM: tegra: cpuidle: implement cpuidle_state.enter_freeze()
ARM: tegra: Disable cpuidle if PSCI is available
soc/tegra: pmc: Use existing pclk reference
soc/tegra: pmc: Remove unnecessary return statement
soc: tegra: Remove redundant $(CONFIG_ARCH_TEGRA) in Makefile
memory: tegra: Add Tegra210 support
memory: tegra: Add support for a variable-size client ID bitfield
clk: shmobile: rz: Add CPG/MSTP Clock Domain support
clk: shmobile: rcar-gen2: Add CPG/MSTP Clock Domain support
clk: shmobile: r8a7779: Add CPG/MSTP Clock Domain support
clk: shmobile: r8a7778: Add CPG/MSTP Clock Domain support
clk: shmobile: Add CPG/MSTP Clock Domain support
ARM: dove: create a proper PMU driver for power domains, PMU IRQs and resets
reset: reset-zynq: Adding support for Xilinx Zynq reset controller.
docs: dts: Added documentation for Xilinx Zynq Reset Controller bindings.
MIPS: ath79: Add the reset controller to the AR9132 dtsi
reset: Add a driver for the reset controller on the AR71XX/AR9XXX
devicetree: Add bindings for the ATH79 reset controller
reset: socfpga: Update reset-socfpga to read the altr,modrst-offset property
doc: dt: add documentation for lpc1850-rgu reset driver
...
New or improved SoC support:
- Addition of support for Atmel's SAMA5D2 SoC
- Addition of Freescale i.MX6UL
- Improved support of TI's DM814x platform
- Misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch are
also here (acked by appropriate maintainers):
- Power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- Clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8T5Z
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New or improved SoC support:
- add support for Atmel's SAMA5D2 SoC
- add support for Freescale i.MX6UL
- improved support for TI's DM814x platform
- misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch
are also here (acked by appropriate maintainers):
- power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: rockchip: pm: Fix PTR_ERR() argument
ARM: imx: mach-imx6ul: Fix allmodconfig build
clk: ti: fix for definition movement
ARM: uniphier: drop v7_invalidate_l1 call at secondary entry
memory: kill off set_irq_flags usage
rtc: snvs: select option REGMAP_MMIO
ARM: brcmstb: select ARCH_DMA_ADDR_T_64BIT for LPAE
ARM: BCM: Enable ARM erratum 798181 for BRCMSTB
ARM: OMAP2+: Fix power domain operations regression caused by 81xx
ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend
ARM: rockchip: set correct stabilization thresholds in suspend
ARM: rockchip: rename osc_switch_to_32k variable
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
ARM: davinci: cp_intc: use IRQCHIP_SKIP_SET_WAKE instead of irq_set_wake callback
soc: mediatek: Fix SCPSYS compilation
ARM: at91/soc: add basic support for new sama5d2 SoC
...
and the addition of new clock drivers. Stephen Boyd has also done a lot
of subsystem-wide driver clean-ups (thanks!). There are also fixes to
the framework core and changes to better split clock provider drivers
from clock consumer drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QAiQ
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Michael Turquette:
"The clk framework changes for 4.3 are mostly updates to existing
drivers and the addition of new clock drivers. Stephen Boyd has also
done a lot of subsystem-wide driver clean-ups (thanks!). There are
also fixes to the framework core and changes to better split clock
provider drivers from clock consumer drivers"
* tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (227 commits)
clk: s5pv210: add missing call to samsung_clk_of_add_provider()
clk: pistachio: correct critical clock list
clk: pistachio: Fix PLL rate calculation in integer mode
clk: pistachio: Fix override of clk-pll settings from boot loader
clk: pistachio: Fix 32bit integer overflows
clk: tegra: Fix some static checker problems
clk: qcom: Fix MSM8916 prng clock enable bit
clk: Add missing header for 'bool' definition to clk-conf.h
drivers/clk: appropriate __init annotation for const data
clk: rockchip: register pll mux before pll itself
clk: add bindings for the Ux500 clocks
clk/ARM: move Ux500 PRCC bases to the device tree
clk: remove duplicated code with __clk_set_parent_after
clk: Convert __clk_get_name(hw->clk) to clk_hw_get_name(hw)
clk: Constify clk_hw argument to provider APIs
clk: Hi6220: add stub clock driver
dt-bindings: clk: Hi6220: Document stub clock driver
dt-bindings: arm: Hi6220: add doc for SRAM controller
clk: atlas7: fix pll missed divide NR in fraction mode
clk: atlas7: fix bit field and its root clk for coresight_tpiu
...
Commit d5e136a21b ("clk: samsung: Register
clk provider only after registering its all clocks", merged to v3.17-rc1)
modified a way that driver registers registers to core framework. This
change has not been applied to s5pv210 clocks driver, which has been
merged in parallel to that commit. This patch adds a missing call to
samsung_clk_of_add_provider(), so the driver is operational again.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: stable@vger.kernel.org # v3.17+
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Current critical clock list for pistachio enables
only mips and sys clocks by default but there are
also other clocks that are not claimed by anyone and
needs to be enabled by default.
This patch updates the critical clocks that need
to be enabled by default.
Add a separate struct to distinguish the critical clocks
as listed:
1.) core clocks:
a.) mips clock
2.) peripheral system clocks:
a.) sys clock
b.) sys_bus clock
c.) DDR clock
d.) ROM clock
Fixes: b35d7c33419c("CLK: Pistachio: Register core clocks")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
.recalc_rate callback for the fractional PLL doesn't take operating
mode into account when calculating PLL rate. This results in
the incorrect PLL rates when PLL is operating in integer mode.
Operating mode of fractional PLL is based on the value of the
fractional divider. Currently it assumes that the PLL will always
be configured in fractional mode which may not be
the case. This may result in the wrong output frequency.
Also vco was calculated based on the current operating mode which
makes no sense because .set_rate is setting operating mode. Instead,
vco should be calculated using PLL settings that are about to be set.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PLL enable callbacks are overriding PLL mode (int/frac) and
Noise reduction (on/off) settings set by the boot loader which
results in the incorrect clock rate.
PLL mode and noise reduction are defined by the DSMPD and DACPD bits
of the PLL control register. PLL .enable() callbacks enable PLL
by deasserting all power-down bits of the PLL control register,
including DSMPD and DACPD bits, which is not necessary since
these bits don't actually enable/disable PLL.
This commit fixes the problem by removing DSMPD and DACPD bits
from the "PLL enable" mask.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresitcker <abrestic@chromium.org>
Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This commit fixes 32bit integer overflows throughout the pll driver
(i.e. wherever the result of integer multiplication may exceed the
range of u32).
One of the functions affected by this problem is .recalc_rate. It
returns incorrect rate for some pll settings (not for all though)
which in turn results in the incorrect rate setup of pll's child
clocks.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The latest Tegra clk pull had some problems. Fix them.
drivers/clk/tegra/clk-tegra124.c:1450:6: warning: symbol 'tegra124_clock_assert_dfll_dvco_reset' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra124.c:1466:6: warning: symbol 'tegra124_clock_deassert_dfll_dvco_reset' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra124.c:1476:5: warning: symbol 'tegra124_reset_assert' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra124.c:1486:5: warning: symbol 'tegra124_reset_deassert' was not declared. Should it be static?
drivers/clk/tegra/clk-dfll.c:590 dfll_load_i2c_lut() warn: inconsistent indenting
drivers/clk/tegra/clk-dfll.c:1448 dfll_build_i2c_lut() warn: unsigned 'td->i2c_lut[0]' is never less than zero.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This contains the DFLL driver needed to implement CPU frequency scaling
on Tegra.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QWKO
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.3-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.3-rc1
This contains the DFLL driver needed to implement CPU frequency scaling
on Tegra.
Fix the enable bit of the pseudorandom number generator clock.
Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Fixes: 3966fab8b6 "clk: qcom: Add MSM8916 Global Clock Controller support"
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Init data marked const should be annotated with __initconst for
correctness and not __initdata. This also fixes LTO builds that
otherwise fail with section mismatch errors.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
[sboyd@codeaurora.org: Dropped hunks that moved const char *
arrays to const char * const]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The structure is xin24m -> pll -> pll-mux (xin24m,pll,xin32k). The pll
does have an init callback to make sure the boot-selected frequency is
using the expected pll settings and resets the same frequency using
the values provided in the driver if necessary.
The setting itself also involves remuxing the pll-mux temporarily to
the xin24m source to let the new pll rate settle. Until now this worked
flawlessly, even when it had the flaw of accessing the mux settings
before the mux actually got registered.
With the recent clock-core conversions this flaw became apparent in
null pointer dereference in
[<c03fc400>] (clk_hw_get_num_parents) from [<c0400df0>] (clk_mux_get_parent+0x14/0xc8)
[<c0400ddc>] (clk_mux_get_parent) from [<c040246c>] (rockchip_rk3066_pll_set_rate+0xd8/0x320)
So to fix that, simply register the pll-mux before the pll, so that
it will be fully initialized when the pll clock executes its init-
callback and possibly touches the pll-mux clock.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The base addresses for the Ux500 PRCC controllers are hardcoded,
let's move them to the clock node in the device tree and delete
the constants.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
__clk_set_parent_after() actually used the second argument then we
could put this duplicate logic in there and call it with a different
order of arguments in the success vs. error paths in this function.
Cc: Mike Turquette <mturquette@linaro.org>
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use the provider based method to get a clock's name so that we
can get rid of the clk member in struct clk_hw one day. Mostly
converted with the following coccinelle script.
@@
struct clk_hw *E;
@@
-__clk_get_name(E->clk)
+clk_hw_get_name(E)
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kevin Cernekee <cernekee@chromium.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On Hi6220, there have some clocks which can use mailbox channel to send
messages to power controller to change frequency; this includes CPU, GPU
and DDR clocks.
For dynamic frequency scaling, firstly need write the frequency value to
SRAM region, and then send message to mailbox to trigger power controller
to handle this requirement. This driver will use syscon APIs to pass SRAM
memory region and use common mailbox APIs for channels accessing.
This init driver will support cpu frequency change firstly.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PLL VCO frequency is given by Fvco = Fref * 2 * NF / NR
in integer-N mode, or by Fvco = Fref * SSN / NR in Spread
Spectrum (fractional-N) mode. Thus fix the missing part
of NR
Signed-off-by: Guo Zeng <guo.zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
bit4 thcpum_cpudiv4_clken r/w
thcpum_cpudiv4_clk clock enable (default: 1)
Root clock CPU_CLK must be enabled for this clock to be enabled
bit3 coresight_tpiu_clken r/w
coresight_tpiu_clk clock enable (default: 0)
Root clock TPIU_CLK must be enabled for this clock to be enabled
Signed-off-by: Guo Zeng <guo.zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
I cannot believe that I spend quite a lot time in finding this bug.
It seems a pitfall people tend to fall in.
In "int64 = int32 * int32", conversion from 32-bits to 64-bits comes
after the multiplication. So this statement may not work as expected.
Signed-off-by: Yibo Cai <yibo.cai@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
this patch makes mux clks can be referenced by device drivers.
Signed-off-by: Guo Zeng <guo.zeng@csr.com>
Signed-off-by: Barry Song <Barry.Song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The debug base clock can be bypassed from the main PLL to the OSC1 clock.
The bypass register is the staysoc1(0x10) register that is in the clock
manager.
This patch adds the option to get the correct parent for the debug base
clock.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This code is unused and not coming back. Let's kill it off.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Remove these APIs now that we've converted all users to the
replacement struct clk_hw based versions.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This driver uses __clk_get_name() when it's dealing with struct
clk_hw pointers. Use the simpler form so that we can get rid of
the clk member in struct clk_hw one day.
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API. This code is
calling the consumer APIs to change the parent to a 1 MHz fixed
rate clock for each of the clocks that the driver provides. Move
to using the assigned-clock-parents DT property for this instead.
Because this is an ABI break, detect if the property is missing
and fall back to setting the parent explicitly before the clocks
are registered.
Acked-by: Pawel Moll <pawel.moll@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: "Emilio López" <emilio@elopez.com.ar>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Cc: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs. This also
removes a clk_get() in this driver that can just as easily use
of_clk_get_parent_name() instead.
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Cc: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This code is never called with a basic clock type, so the check
here is not doing anything useful and is blocking the removal of
__clk_get_flags(). Remove the check so we can delete the
__clk_get_flags() API.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Mostly converted with the following snippet:
@@
struct clk_hw *E;
@@
-__clk_get_flags(E->clk)
+clk_hw_get_flags(E)
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
clk providers shouldn't need to use the consumer APIs (clk.h).
Add provider APIs to replace the __clk_*() APIs that take a
struct clk_hw as their first argument instead of a struct clk.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Enables CPU frequency scaling on Jetson TK1 and enables the GK20A GPU on
Venice2 and Jetson TK1. This also enables support for the PMU hardware
found on Tegra124, which among other things, can be used for performance
measurements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=tdwi
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.3-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
ARM: tegra: Devicetree changes for v4.3-rc1
Enables CPU frequency scaling on Jetson TK1 and enables the GK20A GPU on
Venice2 and Jetson TK1. This also enables support for the PMU hardware
found on Tegra124, which among other things, can be used for performance
measurements.
* tag 'tegra-for-4.3-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
pinctrl: tegra: Only set the gpio range if needed
clk: tegra: Add the DFLL as a possible parent of the cclk_g clock
clk: tegra: Save/restore CCLKG_BURST_POLICY on suspend
clk: tegra: Add Tegra124 DFLL clocksource platform driver
clk: tegra: Add DFLL DVCO reset control for Tegra124
clk: tegra: Introduce ability for SoC-specific reset control callbacks
clk: tegra: Add functions for parsing CVB tables
clk: tegra: Add closed loop support for the DFLL
clk: tegra: Add library for the DFLL clock source (open-loop mode)
clk: tegra: Add binding for the Tegra124 DFLL clocksource
Signed-off-by: Olof Johansson <olof@lixom.net>
- add cpu clock configuration data and instantiate cpu clock
for exynos3250, 4210, 4412 and 5250 SoCs to support Samsung
specific cpu-clock type
* Note this branch has been provided to clk tree as a topic branch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=AWdl
-----END PGP SIGNATURE-----
Merge tag 'samsung-clk-driver' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/late
Samsung clk driver updates for v4.3
- add cpu clock configuration data and instantiate cpu clock
for exynos3250, 4210, 4412 and 5250 SoCs to support Samsung
specific cpu-clock type
* Note this branch has been provided to clk tree as a topic branch
* tag 'samsung-clk-driver' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
clk: exynos4x12: add cpu clock configuration data and instantiate cpu clock
clk: exynos3250: Add cpu clock configuration data and instaniate cpu clock
clk: exynos5250: add cpu clock configuration data and instantiate cpu clock
Signed-off-by: Olof Johansson <olof@lixom.net>
DPLL for am4372 cpsw Ethernet driver. Also add ARM global and
local timers for am4372.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4z1B
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.3/dt-pt4-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Fix up bogus RTC compatible change for am4372 and add missing
DPLL for am4372 cpsw Ethernet driver. Also add ARM global and
local timers for am4372.
* tag 'omap-for-v4.3/dt-pt4-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: dts: am4372: Set the default clock rate for dpll_clksel_mac_clk clock
ARM: dts: AM437X: add dpll_clksel_mac_clk node
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add audio and eTSEC device support and update dspi node for LS1021A.
- Add initial i.MX6UL and imx6ul-14x14-evk board support, and enable
a bunch of device support for i.MX6UL, including RTC, power key, USB,
QSPI, and dual FEC.
- Enable HDMI and LVDS dual display support for a few imx6qdl boards.
- Support of imx6sl-warp board rev1.12, the version which will be
publicly available for the customers.
- A few i.MX7D device additions, watchdog, cortex-a7 coresight
components, RTC, power key, power off.
- Some Vybrid updates: add device support for I2C, QSPI, eSDHC etc.,
update ADC node, and define stdout-path property.
- A few random updates for i.MX27 and i.MX53 devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVyhktAAoJEFBXWFqHsHzOjQwH/0CXyzRUCJjHqxAHsnvHzOZG
AvjYWqaimxP5PD6TRG1bRxfWWXNL7zZGqj9Jd/l5HIWdWfUxnOLeMy40yfcs+AsH
9CHUunu0rahIDY6YF4gA7F5jyfnSIzxwE8Bkva7nmXvf0XmazTwhCXxYPzdBjMSG
Cf39datyTj9ZS3DD/DAKzRN//zebQCJmPuAdmIlRZljBkoLVPeEZrVxkSN0trRin
vKPQIpamM2DXIMmdiPK52J0j8Vwq4qbiGvvAwUKsaRCUVYfpunpVcZSYgMqm8iEa
7PKuurbVeuvZLzS0Bdq05tCkwVXt0upk0ayf0i8DkHFExX79TNTbONOLJwmigjo=
=iAvA
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree updates for 4.3:
- Add audio and eTSEC device support and update dspi node for LS1021A.
- Add initial i.MX6UL and imx6ul-14x14-evk board support, and enable
a bunch of device support for i.MX6UL, including RTC, power key, USB,
QSPI, and dual FEC.
- Enable HDMI and LVDS dual display support for a few imx6qdl boards.
- Support of imx6sl-warp board rev1.12, the version which will be
publicly available for the customers.
- A few i.MX7D device additions, watchdog, cortex-a7 coresight
components, RTC, power key, power off.
- Some Vybrid updates: add device support for I2C, QSPI, eSDHC etc.,
update ADC node, and define stdout-path property.
- A few random updates for i.MX27 and i.MX53 devices.
* tag 'imx-dt-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (44 commits)
ARM: dts: imx6ul: add snvs power key support
ARM: dts: imx6ul: add RTC support
ARM: dts: imx6ul: enable GPC as extended interrupt controller
ARM: dts: imx6sx: correct property name for wakeup source
ARM: dts: add property for maximum ADC clock frequencies
ARM: dts: imx7d: enable snvs rtc, onoffkey and power off
ARM: dts: imx6ul-14x14-evk: add fec1 and fec2 support
ARM: dts: imx: add fec1 and fec2 nodes for SOC i.MX6UL
ARM: dts: imx27: add support of internal rtc
ARM: dts: vf-colibri: define stdout-path property
ARM: dts: ls1021a: Enable the eTSEC ports on QDS and TWR
ARM: dts: ls1021a: Add the eTSEC controller nodes
ARM: dts: imx6ul: add qspi support
ARM: dts: imx6ul: fix low case define in imx6ul-pinfunc.h
ARM: dts: imx6ul: add usb host and function support
ARM: dts: vfxxx: Add io-channel-cells property for ADC node
ARM: dts: ls1021a: Add dts nodes for audio on LS1021A
ARM: imx6qdl-sabreauto.dtsi: enable USB support
ARM: dts: imx: update snvs to use syscon access register
ARM: dts: imx: add imx6ul and imx6ul evk board support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=IHq6
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock fix from Stephen Boyd:
"A one-liner for a regression found in the PXA clock driver"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: pxa: pxa3xx: fix CKEN register access
With the addition of the new Samsung specific cpu-clock type, the
arm clock can be represented as a cpu-clock type. Add the CPU clock
configuration data and instantiate the CPU clock type for Exynos4x12.
Based on the earlier work by Thomas Abraham.
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
pclk_pd_pmu needs to keep running and with the upcoming gpio clock
handling this is not always the case anymore. So add it to the list
of critical clocks for now.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Neither spdif_src nor spdif_pll exists, judging by the vendor kernel in
both cases spdif_pre was meant. This brings the naming in line and
hierachy in line with that of sclk_i2s0.
Also allow sclk_spdif and spdif_frac to change their parents rate as
that the upstream dividers are purely there to feed sclk_spdif
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Nothing uses it, and I can't find any evidence that anything ever has.
Its role is now filled by the core clock in the firmware driver.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
While children of orphan clocks are not carried in the orphan-list itself,
they're nevertheless orphans in their own right as they also don't have an
input-rate available. To ease tracking if a clock is an orphan or has an
orphan in its parent path introduce an orphan field into struct clk and
update it and the fields in child-clocks when a clock gets added or removed
from the orphan-list.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Alex Elder <elder@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: kernel@pengutronix.de
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Chao Xie <chao.xie@marvell.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Barry Song <baohua@kernel.org>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Gabriel FERNANDEZ <gabriel.fernandez@st.com>
Cc: emilio@elopez.com.ar
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Michal Simek <michal.simek@xilinx.com>
[sboyd@codeaurora.org: s/clk/core/ in new function]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The gates were handled with a common piece of framework that was
registering all gates array, that was not using the CLK_OF_DECLARE logic,
and was not using clock-indices but some private masks that were pretty
much equivalent.
Move this code in a new driver that handles all the gates array and solves
both these issues.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
[sboyd@codeaurora.org: Include clk.h for consumer API usage]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The i.MX clock updates for 4.3:
- Provide a better IPU clock initial settings on imx6dl for getting
HDMI and LVDS at the same time.
- Add clock driver support for i.MX6UL SoC
- Add a second clock for RTC device on i.MX31 and i.MX35
Add Clock Domain support to the RZ Clock Pulse Generator (CPG) driver
using the generic PM Domain. This allows to power-manage the module
clocks of SoC devices that are part of the CPG/MSTP Clock Domain using
Runtime PM, or for system suspend/resume.
SoC devices that are part of the CPG/MSTP Clock Domain and can be
power-managed through an MSTP clock should be tagged in DT with a proper
"power-domains" property.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Clock Domain support to the R-Car Gen2 Clock Pulse Generator (CPG)
driver using the generic PM Domain. This allows to power-manage the
module clocks of SoC devices that are part of the CPG/MSTP Clock Domain
using Runtime PM, or for system suspend/resume.
SoC devices that are part of the CPG/MSTP Clock Domain and can be
power-managed through an MSTP clock should be tagged in DT with a proper
"power-domains" property.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Clock Domain support to the R-Car H1 Clock Pulse Generator (CPG)
driver using the generic PM Domain. This allows to power-manage the
module clocks of SoC devices that are part of the CPG/MSTP Clock Domain
using Runtime PM, or for system suspend/resume.
SoC devices that are part of the CPG/MSTP Clock Domain and can be
power-managed through an MSTP clock should be tagged in DT with a proper
"power-domains" property.
Also update the reg property in the DT binding doc example to match the
actual dtsi, which uses #address-cells and #size-cells == 1, not 2.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Clock Domain support to the R-Car M1A Clock Pulse Generator (CPG)
driver using the generic PM Domain. This allows to power-manage the
module clocks of SoC devices that are part of the CPG/MSTP Clock Domain
using Runtime PM, or for system suspend/resume.
SoC devices that are part of the CPG/MSTP Clock Domain and can be
power-managed through an MSTP clock should be tagged in DT with a proper
"power-domains" property.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Clock Domain support to the Clock Pulse Generator (CPG) Module Stop
(MSTP) Clocks driver using the generic PM Domain. This allows to
power-manage the module clocks of SoC devices that are part of the
CPG/MSTP Clock Domain using Runtime PM, or for system suspend/resume.
SoC devices that are part of the CPG/MSTP Clock Domain and can be
power-managed through an MSTP clock should be tagged in DT with a
proper "power-domains" property.
The CPG/MSTP Clock Domain code will scan such devices for clocks that
are suitable for power-managing the device, by looking for a clock that
is compatible with "renesas,cpg-mstp-clocks".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add CAAM clock support to the i.MX6 clocking infrastructure.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We have a driver now for IIC, so disable reset for them.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Clocks 0 to 31 are on CKENA, and not CKENB. The clock register names
were inadequately inverted. As a consequence, all clock operations were
happening on CKENB, because almost all but 2 clocks are on CKENA.
As the clocks were activated by the bootloader in the former tests, it
escaped the testing that the wrong clock gate was manipulated. The error
was revealed by changing the pxa3xx-nand driver to a module, where upon
unloading, the wrong clock was disabled in CKENB.
Fixes: 9bbb8a338f ("clk: pxa: add pxa3xx clock driver")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2014320
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The imx35 don't define clocks for rtc.
This patch add two clocks, as needed
by the mxc rtc driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The mxc rtc driver needs two clock.
It was defined only one clock, so we
define the second clock.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Fix earlyprintk, jump trampoline for SMP
- Update git tree location
- Setup PL310 aux (bit 22)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlW7MWAACgkQykllyylKDCHkTACfT3Kzs+Cl7jc9A4kQ6dkbUqtC
E1MAn0g3yHcqGHgUtfyHu6lXtptJFbDn
=DuTZ
-----END PGP SIGNATURE-----
Merge tag 'zynq-soc-for-4.3' of https://github.com/Xilinx/linux-xlnx into next/soc
arm: Xilinx Zynq SoC patches for v4.2
- Fix earlyprintk, jump trampoline for SMP
- Update git tree location
- Setup PL310 aux (bit 22)
* tag 'zynq-soc-for-4.3' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: reserve space for jump target in secondary trampoline
clk: zynq: remove redundant $(CONFIG_ARCH_ZYNQ) in Makefile
MAINTAINERS: Update Zynq git tree location
ARM: zynq: Set bit 22 in PL310 AuxCtrl register (6395/1)
ARM: zynq: Fix earlyprintk in big endian mode
Signed-off-by: Olof Johansson <olof@lixom.net>
*of_iomap()* will check the device node pointer, and if the pointer is
NULL it will return error code. So refine clock's init flow by checking
the device node with this simple way; and polish a little for the print
out message.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Kbuild descends into drivers/clk/zynq/ only when CONFIG_ARCH_ZYNQ
is enabled. (see drivers/clk/Makefile)
$(CONFIG_ARCH_ZYNQ) in drivers/clk/zynq/Makefile always evaluates
to 'y'.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The ">" should be ">=" or we end up reading beyond the end of the array.
Fixes: 6e973d2c43 ('clk: vexpress: Add separate SP810 driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The TSADC gate clock was used in Exynos4x12 DTSI for exynos-adc driver.
However TSADC is present only on Exynos4210 so on Trats2 board (with
Exynos4412 SoC) the exynos-adc driver could not be probed:
ERROR: could not get clock /adc@126C0000:adc(0)
exynos-adc 126c0000.adc: failed getting clock, err = -2
exynos-adc: probe of 126c0000.adc failed with error -2
Instead on Exynos4x12 SoCs the main clock used by Analog to Digital
Converter is located in different register and it is named in datasheet
as PCLK_ADC. Regardless of the name the purpose of this PCLK_ADC clock
is the same as purpose of TSADC from Exynos4210.
The patch adds gate clock for Exynos4x12 using the proper register so
backward compatibility is preserved. This fixes the probe of exynos-adc
driver on Exynos4x12 boards and allows accessing sensors connected to it
on Trats2 board (ntc,ncp15wb473 AP and battery thermistors).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: c63c574330 ("ARM: dts: Add ADC's dt data to read raw data for exynos4x12")
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also modify IRQ_NOPROBE and this has been maintained although it
is not clear that is really needed. There appears to be a great deal of
blind copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Mike Turquette <mturquette@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The array of parent names can be made as array of const pointers to
const strings.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Rhyland Klein