Commit a471fcde8c ("ALSA: dice: fix detection of Weiss devices") adds
a quirk of Weiss models. According to users' reports, Loud models also
have the similar quirk. They have 0x10 in the category field.
This commit adds support for Mackie Onyx Blackbird and Onyx-i series.
As long as I know, Dice-based models produced by
Focusrite/Alesis/PreSonus/M-Audio/TC Electronic have default value (0x04)
in their category field, thus it may be reasonable to add a condition
statement for Loud models, instead of removing the check of category value.
Reported-by: Rouge Etienne <erouge.externe@m6.fr>
Reported-by: Etilem <contact@etilem.net>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A commit to add support for this model should have added a comment
about this model to Kconfig.
Fixes: 759a2f40c9fa('ALSA: oxfw: add an entry for TASCAM FireOne')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Digi 002/003 family uses two ways to transfer MIDI messages. They're
different mechanisms, while it's better to handle the ways in different
ALSA rawmidi character devices because one character device has just a
set of operations.
This commit adds another rawmidi character device for control MIDI port. As
a result, first rawmidi character device is just for MIDI messages
transferred by isochronous packets.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Digi 002/003 family has two types of MIDI port; one is for physical MIDI
port and another is for MIDI control message. The former is transferred in
isochronous packet, and the latter is transferred by asynchronous
transaction. These transmission mechanisms are completely different, while
current ALSA digi00x driver defines a set of operations for them with
several condition statements. As a result, codes for the operation are
messy.
This commit adds a set of MIDI operation for control MIDI ports. In later
commit, it's applied as an operation for ALSA rawmidi character device.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In following commit, new functions and variables are added for operations
of MIDI control port.
This commit is a preparation. Current identifiers are renamed so that they
mean physical MIDI ports.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When MIDI buffer stores two or more MIDI messages, TASCAM driver
transfers asynchronous transactions including one MIDI message and
extra bytes from second MIDI message.
This commit fixes this bug by clearing needless bytes in the buffer. The
consumed bytes are already calculated correctly, thus the sequence of
transactions is already correct.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In transactions for MIDI messages, the first byte is used for label and
the rest is for MIDI bytes. In current code, these are handled correctly,
while there's a small mistake for loop condition to include meaningless
statement.
This commit adds two local variables for them and improve the loop
condition.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the callback function of asynchronous MIDI port, the intension of some
local variables are not clear.
This commit improves them. The 'len' variable is used to calculate the
number of MIDI bytes including in the transaction. The 'consume' variable
is used to return the actual number of consumed bytes in ALSA MIDI buffer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the callback function of asynchronous MIDI port, some local variables
are declared 'unsigned int', while they're assigned to int value of return
from snd_rawmidi_transmit_peek().
This commit fixes the type.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The given buffer to callback function is cleared in caller side.
This commit removes buffer initialization in callee side.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Let's leave space for the NUL char otherwise the static checkers
complain that we go beyond the end of the array.
Fixes: 53b3ffee78 ('ALSA: firewire-tascam: change device probing processing')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireOne is based on OXFW971 and ALSA OXFW driver can support it.
These are values of identical registers.
$ ./firewire-request /dev/fw1 read 0xfffff0050000
result: 97100105
$ ./firewire-request /dev/fw1 read 0xfffff0090020
result: 39373100
This commit adds an entry for this model. This model has physical controls
and its MIDI control messages are transferred to second MIDI data stream
multiplexed in one MIDI conformant data channel.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In IEC 61883-6, sequence multiplexing is applied to MIDI conformant data
channel. As a result, eight MIDI data streams are included in the channel.
Although ALSA AM824 data block processing layer implements this
multiplexing, current OXFW driver doesn't utilize it due to wrong
calculation of MIDI ports.
This commit fixes this bug to add proper calculation. Although this commit
allows to use 8 MIDI data streams, the number of available MIDI ports is
limited by the number of ALSA MIDI ports added by the driver.
Fixes: df075feefbd3('ALSA: firewire-lib: complete AM824 data block processing layer')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current OXFW driver calculates the number of MIDI ports just before adding
ALSA MIDI ports. It's convenient for some devices with quirks to move
these codes before handling quirks.
This commit implements this idea.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When asynchronous MIDI port is closed before callbacked, the callback
function causes NULL pointer dereference to missing MIDI substream.
This commit fixes this bug.
Fixes: e8a40d9bcb23('ALSA: firewire-lib: schedule work again when MIDI substream has rest of MIDI messages')
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The contents of Config ROM in firewire device structure are already
aligned to CPU-endianness. Thus, no need to convert it again.
This commit removes needless conversions
Fixes: 9edf723fd858('ALSA: firewire-digi00x: add skeleton for Digi 002/003 family')
Fixes: c0949b278515('ALSA: firewire-tascam: add skeleton for TASCAM FireWire series')
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commit, metering is supported for BeBoB based models
customized by M-Audio. The data in transaction is aligned to
big-endianness, while in the driver code u16 typed variable is assigned
to the data. This causes sparse warnings.
bebob_maudio.c:651:31: warning: cast to restricted __be16
bebob_maudio.c:651:31: warning: cast to restricted __be16
bebob_maudio.c:651:31: warning: cast to restricted __be16
bebob_maudio.c:651:31: warning: cast to restricted __be16
This commit fixes this bug by using __be16 variable for the data.
Fixes: 3149ac489ff8('ALSA: bebob: Add support for M-Audio special Firewire series')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commit, snd_efw_command_get_phys_meters() was added to handle
metering data. The given buffer is used to save transaction result and to
convert between endianness. But this causes sparse warnings.
fireworks_command.c:269:25: warning: incorrect type in argument 1 (different base types)
fireworks_command.c:269:25: expected unsigned int [usertype] *p
fireworks_command.c:269:25: got restricted __be32 [usertype] *
This commit fixes this bug.
Fixes: bde8a8f23bbe('ALSA: fireworks: Add transaction and some commands')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commit, u32 data was assigned to __be32 variable instead of an
int variable. This is not enough solution because it still causes sparse
warnings.
dice.c:80:23: warning: incorrect type in assignment (different base types)
dice.c:80:23: expected restricted __be32 [usertype] value
dice.c:80:23: got unsigned int
dice.c:81:21: warning: restricted __be32 degrades to integer
dice.c:81:46: warning: restricted __be32 degrades to integer
This commit fixes this bug.
Fixes: 7c2d4c0cf5ba('ALSA: dice: Split transaction functionality into a file')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some local variables in some functions are typed as unsigned int, while
__be32 value is assigned to them. This causes sparse warnings.
dice-stream.c:50:17: warning: incorrect type in assignment (different base types)
dice-stream.c:50:17: expected unsigned int [unsigned] channel
dice-stream.c:50:17: got restricted __be32 [usertype] <noident>
dice-stream.c:74:17: warning: incorrect type in assignment (different base types)
dice-stream.c:74:17: expected unsigned int [unsigned] channel
dice-stream.c:74:17: got restricted __be32 [usertype] <noident>
This commit fixes this bug.
Fixes: 288a8d0cb04f('ALSA: dice: Change the way to start stream')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A former commit moves oxfw-related codes to a sub-directory, while it
forgot to remove an entry from Makefile in parent directory.
Fixes: 1a4e39c2e5ca('ALSA: oxfw: Move to its own directory')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When committed to upstream, these four modules had wrong entries for
Makefile. This forces them to be loadable modules even if they're set
as built-in.
This commit fixes this bug.
Fixes: b5b04336015e('ALSA: fireworks: Add skelton for Fireworks based devices')
Fixes: fd6f4b0dc167('ALSA: bebob: Add skelton for BeBoB based devices')
Fixes: 1a4e39c2e5ca('ALSA: oxfw: Move to its own directory')
Fixes: 14ff6a094815('ALSA: dice: Move file to its own directory')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
My static checker complains because tscm->spec->midi_capture_ports is
either 2 or 4 but the tscm->tx_midi_substreams[] array has 4 elements so
this is possibly off by one. I have looked at the code and I think it
should be >= instead of > as well.
Fixes: 107cc0129a ('ALSA: firewire-tascam: add support for incoming MIDI messages by asynchronous transaction')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We recently tried to add some new code to support turning the LED on and
off but the code in snd_tscm_transaction_reregister() is unreachable.
Fixes: e65e2cb99e ('ALSA: firewire-tascam: Turn on/off FireWire LED')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, this driver picks up model name with be32_to_cpu() macro
to align characters. This is wrong operation because the result is
different depending on CPU endiannness.
Additionally, vendor released several versions of firmware for this
series. It's not better to assign model-dependent information to
device entry according to the version field.
This commit fixes these bugs. The name of model is picked up correctly
and used to identify model-dependent information.
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fixes: c0949b2785 ('ALSA: firewire-tascam: add skeleton for TASCAM FireWire series')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series has some LEDs on its surface. These LEDs can be
turned on/off by receiving asynchronous transactions to a certain
address. One of the LEDs is labels as 'FireWire'. It's better to light it
up when this driver starts to work. Besides, the LED for 'FireWire' is
turned off at bus reset.
This commit implements this idea.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commits, this driver got functionalities to transfer/receive
MIDI messages to/from TASCAM FireWire series.
This commit adds some ALSA MIDI ports to enable userspace applications
to use the functionalities.
I note that this commit doesn't support virtual MIDI ports which console
models support. A physical controls can be assigned to a certain MIDI
ports including physical and virtual. But the way is not clear.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series use asynchronous transaction to receive MIDI
messages. The transaction should be sent to a certain address.
This commit supports the outgoing MIDI messages. The messages in the
transaction includes some quirks:
* One MIDI message is transferred in one quadlet transaction, except for
system exclusives.
* MIDI running status is not allowed, thus transactions always include
status byte.
* The basic data format is the same as transferring MIDI messages
supported in previous commit.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series use asynchronous transaction to transfer MIDI
messages. The transaction is sent to a registered address.
This commit supports the incoming MIDI messages. The messages in the
transaction include some quirks:
* Two quadlets are used for one MIDI message and one timestamp.
* Usually, the first byte of the first quadlet includes MIDI port and MSB
4 bit of MIDI status. For system exclusive message, the first byte
includes MIDI port and 0x04, or 0x07 in the end of the message.
* The rest of the first quadlet includes MIDI bytes up to 3.
* Several set of MIDI messages and timestamp can be transferred in one
block transaction, up to 8 sets.
I note that TASCAM FireWire series ignores ID bytes of system exclusive
message. When receiving system exclusive messages with ID bytes on physical
MIDI bus, the series transfers the messages without ID bytes on IEEE 1394
bus, and vice versa.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commits, asynchronous transactions are supported for physical
controls. This commit adds a pair of MIDI ports for them.
This driver already adds diferrent number of ALSA MIDI ports for physical
MIDI ports, and the number of in/out ports are different. As seeing as
'amidi' program in alsa-utils package, a pair of in/out MIDI ports is
expected with the same name. Therefore, this commit adds a pair of new
ports to the first.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In previous commit, asynchronous transaction for incoming MIDI messages
from physical controls is supported. The physical controls may be
controlled by receiving MIDI messages at a certain address.
This commit supports asynchronous transaction for this purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Digi 00x series has two types of model; rack and console. The console
models have physical controls. The model can transmit control messages.
These control messages are transferred by asynchronous transactions to
registered address.
This commit supports the asynchronous transaction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds MIDI functionality to capture/playback MIDI messages
from/to physical MIDI ports. These messages are transferred in isochronous
packets.
When no substreams request AMDTP streams to run, this driver starts the
streams at current sampling rate. When other substreams start at different
sampling rate, the streams are stopped temporarily, then start again at
requested sampling rate. This operation can generate missing MIDI bytes,
thus it's preferable to start PCM substreams at favorite sampling rate in
advance.
Digi 002/003 console also has a set of MIDI port for physical controls.
These ports are added in later commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In Digi 002/003 protocol, MIDI messages are transferred in the last data
channel of data blocks. Although this data channel has a label of 0x80,
it's not fully MIDI conformant data channel especially because the Counter
field always zero independently of included MIDI bytes. The 4th byte of
the data channel in LSB tells the number of included MIDI bytes. This byte
also includes the number of MIDI port. Therefore, the data format in this
data channel is:
* 1st: 0x80 as label
* 2nd: MIDI bytes
* 3rd: 0 or MIDI bytes
* 4th: the number of MIDI byte and the number of MIDI port
This commit adds support of MIDI messages in data block processing layer.
Like AM824 data format, this data channel has a capability to transfer
more MIDI messages than the capability of phisical MIDI bus. Therefore, a
throttle for data rate is required to prevent devices' internal buffer to
overflow.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Original code for 'DoubleOhThree' encoding was written with '__u8' type,
while the type is usually used to export something to userspace.
This commit replaces the type with 'u8'.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In firewire-lib, isochronous packet streaming is stopped when detecting
wrong value for FMT field of CIP headers. Although this is appropriate
to IEC 61883-1 and 6, some BeBoB based devices with vendors' customization
use invalid value to FMT field of CIP headers in the beginning of
streaming.
$ journalctl
snd-bebob fw1.0: Detect unexpected protocol: 01000000 8000ffff
I got this log with M-Audio FireWire 1814. In this line, the value of FMT
field is 0x00, while it should be 0x10 in usual AMDTP.
Except for the beginning, these devices continue to transfer packets with
valid value for FMT field, except for the beginning. Therefore, in this
case, firewire-lib should continue to process packets. The former
implementation of firewire-lib performs it.
This commit loosens the handling of wrong value, to continue packet
processing in the case.
Fixes: 414ba022a5 ('ALSA: firewire-lib: add support arbitrary value for fmt/fdf fields in CIP header')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The structures of type snd_bebob_clock_spec, snd_bebob_rate_spec,
snd_bebob_meter_spec, and snd_bebob_spec are never modified after they are
initialized. Make them all const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, when asynchronous transactions finish in error state and
retries, work scheduling and work running also continues. This
should be canceled at fatal error because it can cause endless loop.
This commit enables to cancel transferring MIDI messages when transactions
encounter fatal errors. This is achieved by setting error state.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Typically, the target devices have internal buffer to adjust output of
received MIDI messages for MIDI serial bus, while the capacity of the
buffer is limited. IEEE 1394 transactions can transfer more MIDI messages
than MIDI serial bus can. This can cause buffer over flow in device side.
This commit adds throttle to limit MIDI data rate by counting intervals
between two MIDI messages. Usual MIDI messages consists of two or three
bytes. This requires 1.302 to 1.953 mili-seconds interval between these
messages. This commit uses kernel monotonic time service to calculate the
time of next transaction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, when two MIDI trigger callbacks can be called immediately,
transactions for the second MIDI messages can be postpone till next trigger
callback. This is not good for real-time message transmission.
This commit schedules work again at response handling callback if the
MIDI substream still includes untransferred MIDI messages.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, when waiting for a response, callers can start another
transaction by scheduling another work. This is not good for error
processing of transaction, especially the first response is too late.
This commit serialize request/response transactions, by adding one
boolean member to represent idling state.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some models receive MIDI messages via IEEE 1394 asynchronous transactions.
In this case, MIDI messages are transferred in fixed-length payload. It's
nice that firewire-lib module has common helper functions.
This commit implements this idea. Each driver adds
'struct snd_fw_async_midi_port' in its instance structure. In probing,
it should call snd_fw_async_midi_port_init() to initialize the
structure with some parameters such as target address, the length
of payload in a transaction and a pointer for callback function
to fill the payload buffer. At 'struct snd_rawmidi_ops.trigger()'
callback, it should call 'snd_fw_async_midi_port_run()' to start
transactions. Each driver should ensure that the lifetime of MIDI
substream continues till calling 'snd_fw_async_midi_port_finish()'.
The helper functions support retries to transferring MIDI messages when
transmission errors occur. When transactions are successful, the helper
functions call 'snd_rawmidi_transmit_ack()' internally to consume MIDI
bytes in the buffer. Therefore, Each driver is expected to use
'snd_rawmidi_transmit_peek()' to tell the number of bytes to transfer to
return value of 'fill' callback.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other IEEE 1394 sound devices
has.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds PCM functionality to transmit/receive PCM samples.
When one of PCM substreams are running or external clock source is
selected, current sampling rate is used. Else, the sampling rate is
changed as an userspace application requests.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds streaming functionality for both direction. To utilize
the sequence of the number of data blocks in packets, full duplex with
synchronization is applied.
Besides, TASCAM FireWire series allows drivers to decide which PCM data
channels are enabled. For convenience, this driver always enable whole the
data channels.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series uses non-blocking transmission for AMDTP packet
streaming, while the format of data blocks is unique.
The CIP headers includes specific value in FMT field and no SYT
information.
In transmitted packets, the first data channel represents event counter,
and the last data channel has status and control information. The rest
has 24bit PCM samples with right padding.
In received packets, all of data channels include 16, 24, 32bit PCM
samples. There's no other kind of information.
This commit adds support for this protocol. For convenience, the size of
PCM samples in outgoing packet is limited by 16 and 24bit. The status and
control information will be supported in future commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series has certain registers for firmware information.
This commit adds proc node to show the information.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TASCAM FireWire series doesn't tell drivers their capabilities, thus
the drivers should have model-dependent parameters and apply it to
detected devices.
This commit adds a structure to represent such parameters.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for TASCAM FireWire series. In this commit,
this driver just creates/removes card instance according to bus event.
More functionalities will be added in following commits.
TASCAM FireWire series consists of:
* PDI 1394P23 for IEEE 1394 PHY layer
* PDI 1394L40 for IEEE 1394 LINK layer and IEC 61883 interface
* XILINX XC9536XL
* XILINX Spartan-II XC2S100
* ATMEL AT91M42800A
Ilya Zimnovich had investigated TASCAM FireWire series in 2011, and
discover some features of his FW-1804. You can see a part of his research
in FFADO project.
http://subversion.ffado.org/wiki/Tascam
A part of my work are based on Ilya's investigation, while this series
doesn't support the FW-1804, because of a lack of config ROM
information and its protocol detail, especially for PCM channels.
I observed that FW-1884 and FW-1082 don't work properly with 1394 OHCI
controller based on VT6315. The controller can actually communicate packets
to these models, while these models generate no sounds. It may be due to
the PHY/LINK layer issues. Using 1394 OHCI controller produced by the other
vendors such as Texas Instruments may work. Or adding another node on the
bus.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto