Add DSD support for new Amanero Combo384 firmware version with a new
PID. This firmware uses DSD_U32_BE.
Fixes: 3eff682d76 ("ALSA: usb-audio: Support both DSD LE/BE Amanero firmware versions")
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A Senheisser headset requires the typical sample-rate quirk for
avoiding spurious errors from inquiring the current sample rate like:
usb 1-1: 2:1: cannot get freq at ep 0x4
usb 1-1: 3:1: cannot get freq at ep 0x83
The USB ID 1395:740a has to be added to the entries in
snd_usb_get_sample_rate_quirk().
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1052580
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add missing endianness conversion when using the USB device-descriptor
bcdDevice field when applying the Amanero Combo384 (endianness!) quirk.
Fixes: 3eff682d76 ("ALSA: usb-audio: Support both DSD LE/BE Amanero firmware versions")
Cc: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Plantronics BT600 does not support reading the sample rate which leads
to many lines of "cannot get freq at ep 0x1" and "cannot get freq at
ep 0x82". This patch adds the USB ID of the BT600 to quirks.c and
avoids those error messages.
Signed-off-by: Dennis Kadioglu <denk@post.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add DSD support for both little endian (DSD_U32_LE) and big endian
(DSD_U32_BE) version of the Amanero firmware.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds native DSD support for the following devices.
- TEAC NT-503
- TEAC UD-503
- TEAC UD-501
(1) Add quirks for native DSD support for TEAC devices.
(2) A specific vendor command is needed to switch between PCM/DOP and
DSD mode, same as Denon/Marantz devices.
Signed-off-by: Nobutaka Okabe <nob77413@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Avoid getting sample rate on B850V3 CP2114 as it is unsupported and
causes noisy "current rate is different from the runtime rate" messages
when playback starts.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The quirk seems to be necessary not only for TEAC UD-H01 devices, but to
more that are based on the Tenor 8802TL chipset. Devices built by T+A
are affected too, and they apparently all use the same USB PID:PID.
Extend the quirky handling for that device as well, and rename the
quirks flag.
Reported-and-tested-by: Thomas Gresens <T.Gresens@intershop.de>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
That's a quirk, after all, so move it where to all the other quirks
live.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ELP HD USB Camera (05a3:9420) needs this quirk for suppressing
the unsupported sample rate inquiry.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98481
Cc: <stable@vger.kernel.org>
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VF0610 does not support reading the sample rate which leads to many
lines of "cannot get freq at ep 0x82". This patch adds the USB ID
(0x041E:4080) to snd_usb_get_sample_rate_quirk() list.
Signed-off-by: Piotr Karasinski <peter.karasinski@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Phoenix Audio has yet another device with another id (even a different
vendor id, 0556:0014) that requires the same quirk for the sample
rate.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=110221
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Phoenix Audio MT202pcs (1de7:0114) and MT202exe (1de7:0013) need the
same workaround as TMX320 for avoiding the firmware bug. It fixes the
frequent error about the sample rate inquiries and the slow device
probe as consequence.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=117321
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Plantronics BT300 does not support reading the sample rate which leads
to many lines of "cannot get freq at ep 0x1". This patch adds the USB
ID of the BT300 to quirks.c and avoids those error messages.
Signed-off-by: Dennis Kadioglu <denk@post.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Phoenix Audio TMX320 gives the similar error when the sample rate is
asked:
usb 2-1.3: 2:1: cannot get freq at ep 0x85
usb 2-1.3: 1:1: cannot get freq at ep 0x2
....
Add the corresponding USB-device ID (1de7:0014) to
snd_usb_get_sample_rate_quirk() list.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=110221
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
create_fixed_stream_quirk(), snd_usb_parse_audio_interface() and
create_uaxx_quirk() functions allocate the audioformat object by themselves
and free it upon error before returning. However, once the object is linked
to a stream, it's freed again in snd_usb_audio_pcm_free(), thus it'll be
double-freed, eventually resulting in a memory corruption.
This patch fixes these failures in the error paths by unlinking the audioformat
object before freeing it.
Based on a patch by Takashi Iwai <tiwai@suse.de>
[Note for stable backports:
this patch requires the commit 902eb7fd1e ('ALSA: usb-audio: Minor
code cleanup in create_fixed_stream_quirk()')]
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1283358
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Cc: <stable@vger.kernel.org> # see the note above
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Microsoft HD-5001 webcam microphone does not support sample rate
reading as the HD-5000 one.
This results in dmesg errors and sound hanging with pulseaudio.
Signed-off-by: Victor Clément <victor.clement@openmailbox.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
create_fixed_stream_quirk() may cause a NULL-pointer dereference by
accessing the non-existing endpoint when a USB device with a malformed
USB descriptor is used.
This patch avoids it simply by adding a sanity check of bNumEndpoints
before the accesses.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=971125
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Plantronics DA45 does not support reading the sample rate which leads
to many lines of "cannot get freq at ep 0x4" and "cannot get freq at
ep 0x84". This patch adds the USB ID of the DA45 to quirks.c and
avoids those error messages.
Signed-off-by: Dennis Kadioglu <denk@post.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Microsoft LifeCam HD-6000 (045e:076f) requires the similar quirk for
avoiding the stall due to the invalid sample rate reads.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111491
Signed-off-by: Lev Lybin <lev.lybin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In my patch adding native DSD support for the Oppo HA-1, the wrong vendor ID got
through. This patch fixes the vendor ID and aligns the comment.
Fixes: a4eae3a506 ('ALSA: usb: Add native DSD support for Oppo HA-1')
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a preliminary patch for the later change to allow a better
quirk ID management. In the current USB-audio code, there are a few
places looking at usb_device idVendor and idProduct fields directly
even though we have already a static member in snd_usb_audio.usb_id.
This patch modifies such codes to refer to the latter field.
For achieving this, two slightly intensive changes have been done:
- The snd_usb_audio object is set/reset via dev_getdrv() for the given
USB device; it's needed for minimizing the changes for some existing
quirks that take only usb_device object.
- __snd_usbmidi_create() is introduced to receive the pre-given usb_id
argument. The exported snd_usbmidi_create() is unchanged by calling
this new function internally.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TEAC UD-501/UD-503/NT-503 fail to switch properly between different
rate/format. Similar to 'Playback Design', this patch corrects the
invalid clock source error for TEAC products and avoids complete
freeze of the usb interface of 503 series.
Signed-off-by: Guillaume Fougnies <guillaume@eulerian.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds native DSD support for the Oppo HA-1. It uses a XMOS chipset
but they use their own vendor ID.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Avoid getting sample rate on AudioQuest DragonFly as it is unsupported
and causes noisy "cannot get freq at ep 0x1" messages when playback
starts.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The CH345 USB MIDI chip has two output ports. However, they are
multiplexed through one pin, and the number of ports cannot be reduced
even for hardware that implements only one connector, so for those
devices, data sent to either port ends up on the same hardware output.
This becomes a problem when both ports are used at the same time, as
longer MIDI commands (such as SysEx messages) are likely to be
interrupted by messages from the other port, and thus to get lost.
It would not be possible for the driver to detect how many ports the
device actually has, except that in practice, _all_ devices built with
the CH345 have only one port. So we can just ignore the device's
descriptors, and hardcode one output port.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Zoom R16/24 have a nonstandard playback format where each isochronous
packet contains a length descriptor in the first four bytes. (Curiously,
capture data does not contain this and requires no quirk.)
The quirk involves adding the extra length descriptor whenever outgoing
isochronous packets are generated, both in pcm.c (outgoing audio) and
endpoint.c (silent data).
In order to make the quirk as unintrusive as possible, for
pcm.c:prepare_playback_urb(), the isochronous packet descriptors are
initially set up in the same way no matter if the quirk is enabled or not.
Once it is time to actually copy the data into the outgoing packet buffer
(together with the added length descriptors) the isochronous descriptors
are adjusted in order take the increased payload length into account.
For endpoint.c:prepare_silent_urb() it makes more sense to modify the
actual function, partly because the function is less complex to start with
and partly because it is not as time-critical as prepare_playback_urb()
(whose bulk is run with interrupts disabled), so the (minute) additional
time spent in the non-quirk case is motivated by the simplicity of having
a single function for all cases.
The quirk is controlled by the new tx_length_quirk member in struct
snd_usb_substream and struct snd_usb_audio, which is conveyed to pcm.c
and endpoint.c from quirks.c in a similar manner to the txfr_quirk member
in the same structs.
In contrast to txfr_quirk however, the quirk is enabled directly in
quirks.c:create_standard_audio_quirk() by checking the USB ID in that
function. Another option would be to introduce a new
QUIRK_AUDIO_ZOOM_INTERFACE or somesuch, which would have made the quirk
very plain to see in the quirk table, but it was felt that the additional
code needed to implement it this way would just make the implementation
more complex with no real gain.
Tested with a Zoom R16, both by doing capture and playback separately
using arecord and aplay (8 channel capture and 2 channel playback,
respectively), as well as capture and playback together using Ardour, as
well as Audacity and Qtractor together with jackd.
The R24 is reportedly compatible with the R16 when used as an audio
interface. Both devices share the same USB ID and have the same number of
inputs (8) and outputs (2). Therefore "R16/24" is mentioned throughout the
patch.
Regression tested using an Edirol UA-5 in both class compliant (16-bit)
and "advanced" (24 bit, forces the use of quirks) modes.
Signed-off-by: Ricard Wanderlof <ricardw@axis.com>
Tested-by: Panu Matilainen <pmatilai@laiskiainen.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds native DSD support for the Gustard DAC-X20U.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds native DSD support for the XMOS based JLsounds I2SoverUSB board
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This quirk allows us to avoid the noisy:
current rate 0 is different from the runtime rate
message every time playback starts. While USB DAC in the RR2150
supports reading the sample rate, it never returns a sample rate
other than zero in my observation with common sample rates.
Signed-off-by: Eric Wong <normalperson@yhbt.net>
Cc: Joe Turner <joe@oampo.co.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Microsoft LifeCam Studio (045e:0772) needs a similar quirk for
suppressing the wrong sample rate inquiry.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98481
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds Microsoft LifeCam Cinema USB ID to the snd_usb_get_sample_rate_quirk list as the Lifecam Cinema does not appear to support getting the sample rate.
Fixes the issue where the LifeCam Cinema would wait for USB timeout and log the message "cannot get freq at ep 0x82" when accessed.
Addresses bug report https://bugzilla.kernel.org/show_bug.cgi?id=95961.
Signed-off-by: Adam Honse <calcprogrammer1@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding this quirk allows us to avoid the noisy
"cannot get freq at ep 0x1" message in dmesg output every time
playback starts.
This ought to affect other Benchmark DAC1 variations using the same
"Microchip Technology, Inc." chip as well, but I have only tested
with the "Pre" variant.
Signed-off-by: Eric Wong <normalperson@yhbt.net>
Cc: Joe Turner <joe@oampo.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix problem where playback of Denon DA-300USB DAC sometimes does not
start and leads to error messages like "clock source 41 is not valid,
cannot use".
Solution: Treat this device the same as other Denon/Marantz devices in
sound/usb/quirks.c.
Tested with both PCM and DSD formats.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93261
Signed-off-by: Frank C Guenther <bugzilla.frnkcg@spamgourmet.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds a quirk to disable the check that the sample rate has been set correctly, as the Lifecam does not support getting the sample rate.
This means that we don't need to wait for the USB timeout when attempting to get the sample rate. Waiting for the timeout causes problems in some applications, which give up on the device acquisition process before it has had time to complete, resulting in no sound.
[minor tidy up by tiwai]
Signed-off-by: Joe Turner <joe@oampo.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds native DSD support for two XMOS based DACs from Matrix Audio:
- X-Sabre
- Mini-i Pro
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This makes the midi interface and capture work out of the box with
R16 (and presumably R24 too but untested). Playback stream would also
seem to function fine except for one caveat: no sound is produced,
so it is disabled for now. Mixer descriptors are garbage and will
require further quirks to enable functionality, also disabled here.
Signed-off-by: Panu Matilainen <pmatilai@laiskiainen.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [7a2e9ddc: ALSA: usb-audio: Add native DSD support for
Denon/Marantz DACs] requires the new format definition that has
landed only in for-next branch.
Denon/Marantz USB DACs need a specific vendor command to switch between PCM and
DSD mode. This patch adds a new quirk function to switch between the two modes
using the specific USB vendor command.
This patch applies to the following devices:
- Marantz SA-14S1
- Marantz HD-DAC1
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jussi Laako