CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a typo here so we do a double lock instead of an unlock.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FPGA can't handled unaligned DMA (yet). So copy into an aligned buffer,
if skb->data isn't suitably aligned.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dwmw2: Tidy up a little, simpler matching on which GPIO is being accessed,
only register on newer boards, register under PCI device instead of
duplicating them under each ATM device.
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We weren't clearing card->tx_skb[port] when processing the TX done interrupt.
If there wasn't another skb ready to transmit immediately, this led to a
double-free because we'd free it *again* next time we did have a packet to
send.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
David Woodhouse says:
====================
This is the result of pulling on the thread started by Krzysztof Mazur's
original patch 'pppoatm: don't send frames to destroyed vcc'.
Various problems in the pppoatm and br2684 code are solved, some of which
were easily triggered and would panic the kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- Flush pending TX skbs from the queue rather than waiting for them all to
complete (suggested by Krzysztof Mazur <krzysiek@podlesie.net>).
- Clear ATM_VF_ADDR only when the PKT_PCLOSE packet has been submitted.
- Don't clear ATM_VF_READY at all — vcc_destroy_socket() does that for us.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
... and ensure that the next skb is set up for RX in the DMA case.
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We should no longer be calling the old pop routine for the vcc, after
vcc_release() has completed. Make sure we wait for any pending TX skbs
to complete, by waiting for our own PKT_PCLOSE control skb to be sent.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There was a forever loop introduced here when we converted this to
request_firmware() back in 2008.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA support has finally made its way to the top of the TODO list, having
realised that a Geode using MMIO can't keep up with two ADSL2+ lines
each running at 21Mb/s.
This patch fixes a couple of bugs in the DMA support in the driver, so
once the corresponding FPGA update is complete and tested everything
should work properly.
We weren't storing the currently-transmitting skb, so we were never
unmapping it and never freeing/popping it when the TX was done.
And the addition of pci_set_master() is fairly self-explanatory.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent changes for how we compute the skb truesize it occurs to me
we are probably going to have a lot of calls to skb_end_pointer -
skb->head. Instead of running all over the place doing that it would make
more sense to just make it a separate inline skb_end_offset(skb) that way
we can return the correct value without having gcc having to do all the
optimization to cancel out skb->head - skb->head.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'break' is unnecessary after 'return' statement.
Remove all such 'break' as clean up.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
- add eni_do_release() to balance eni_do_init
- turn the zeroes DMA area into a per device data
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert calls to free_irq so that the second argument is the same as the
last argument of the corresponding call to request_irq. Without this
property, free_irq does nothing.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
The calls to pci_iounmap are in the wrong order, as compared to the
associated calls to pci_iomap.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,x;
statement S,S1;
int ret;
@@
e = pci_iomap(x,...)
... when != pci_iounmap(x,e)
if (<+...e...+>) S
... when any
when != pci_iounmap(x,e)
*if (...)
{ ... when != pci_iounmap(x,e)
return ...; }
... when any
pci_iounmap(x,e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct spelling "reseting" to resetting" in
drivers/atm/lanai.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
dp83640: free packet queues on remove
dp83640: use proper function to free transmit time stamping packets
ipv6: Do not use routes from locally generated RAs
|PATCH net-next] tg3: add tx_dropped counter
be2net: don't create multiple RX/TX rings in multi channel mode
be2net: don't create multiple TXQs in BE2
be2net: refactor VF setup/teardown code into be_vf_setup/clear()
be2net: add vlan/rx-mode/flow-control config to be_setup()
net_sched: cls_flow: use skb_header_pointer()
ipv4: avoid useless call of the function check_peer_pmtu
TCP: remove TCP_DEBUG
net: Fix driver name for mdio-gpio.c
ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
ipv4: fix ipsec forward performance regression
jme: fix irq storm after suspend/resume
route: fix ICMP redirect validation
net: hold sock reference while processing tx timestamps
tcp: md5: add more const attributes
Add ethtool -g support to virtio_net
...
Fix up conflicts in:
- drivers/net/Kconfig:
The split-up generated a trivial conflict with removal of a
stale reference to Documentation/networking/net-modules.txt.
Remove it from the new location instead.
- fs/sysfs/dir.c:
Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
with Eric Biederman's changes for tagged directories.
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly PHY access and a few (ugly) debug statements for DMA control.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Cc: linux-atm-general@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver reads PCI subsystem IDs from the PCI configuration registers while
it is already stored by the PCI subsystem in the 'subsystem_device' field of
'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro FILL_RX_POOLS_IN_BH is never been used, in order to avoid
the compiler reports error because of the usage of function INIT_WORK,
we just delete the marco.
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Cc: linux-atm-general@lists.sourceforge.net
Signed-off-by: Wang Shaoyan <wangshaoyan.pt@taobao.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This is just a readback to entire completion of a register
write, keep the readback but kill the unused variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
Two cases here:
1) idt77252_rx_raw() really does not make any use of the
extracted PTI field of the atm header.
2) idt77252_collect_stat() only uses the register values
in code which has been compiled out by a "NOTDEF" cpp
test for more than 10 years. Just kill this NOTDEF
code entirely, but keep the register reads in case
they have side effects.
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC complains in these queue index operations because we
perform operations of the form:
x = some_operation(++x);
which is undefined. Replace with:
x = some_operation(x + 1);
which is well defined and provides the intended operation.
Signed-off-by: David S. Miller <davem@davemloft.net>
The "iavcc" and "iadev" cases are obvious.
The intr_status and frmr_intr cases are reading a register to clear
the chip status. This driver is pretty old and creaky, and uses
volatile pointer dereferences to do register I/O when it should be
using readl() and friends. However that it outside of the scope of
these changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't flap VCs when carrier state changes; higher-level protocols
can detect loss of connectivity and act accordingly. This is more
consistent with how other network interfaces work.
We no longer use release_vccs() so we can delete it.
release_vccs() was duplicated from net/atm/common.c; make the
corresponding function exported, since other code duplicates it
and could leverage it if it were public.
Signed-off-by: Philip A. Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Omit pkt_hdr preamble when dumping transmitted packet as hex-dump;
we can pull this up because the frame has already been sent, and
dumping it is the last thing we do with it before freeing it.
Also include the size, vpi, and vci in the debug as is done on
receive.
Use "port" consistently instead of "device" intermittently.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use VPI.VCI notation consistently throughout the module. This is the
one remaining place where the VCI is used before the VPI in any output.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
Final step to eliminate of_platform_bus_type. They're all just
platform drivers now.
v2: fix type in pasemi_nand.c (thanks to Stephen Rothwell)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If alloc_skb() fails to allocate memory and returns NULL then we want to
return -ENOMEM from drivers/atm/solos-pci.c::popen() regardless of the
value of net_ratelimit(). The way the code is today, we may not return if
net_ratelimit() returns 0, then we'll proceed to pass a NULL pointer to
skb_put() which will blow up in our face.
This patch ensures that we always return -ENOMEM on alloc_skb() failure
and only let the dev_warn() be controlled by the value of net_ratelimit().
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
copy_to_user() used PRIV(dev)->stats instead of local stats variable.
Zero stats were returned to user in case of (zero != 0), also memcpy()
was pointless.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure to call release_firmware() will result in memory leak in
drivers/atm/ambassador.c::ucode_init().
This patch makes sure we always call release_firmware() when needed,
thus removing the leak(s).
Yes, I know checkpatch complains about this patch, but it was either that
or completely mess up the existing style, so I opted to use the existing
style and live with the checkpatch related flak.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The earlier call to atm_dev_lookup increases the reference count of dev,
so decrease it on the way out.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x, E;
constant C;
@@
x = atm_dev_lookup(...);
... when != false x != NULL
when != true x == NULL
when != \(E = x\|x = E\)
when != atm_dev_put(dev);
*return -C;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
The ATM subsystem was incorrectly creating the 'device' link for ATM
nodes in sysfs. This led to incorrect device/parent relationships
exposed by sysfs and udev. Instead of rolling the 'device' link by hand
in the generic ATM code, pass each ATM driver's bus device down to the
sysfs code and let sysfs do this stuff correctly.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Cc: linux-atm-general@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC (rightfully) complains that:
drivers/atm/fore200e.c:614:5: warning: operation on 'cmdq->head' may be undefined
This is due to the FORE200E_NEXT_ENTRY macro, which essentially
evaluates to:
i = ++i % m
Make it what's explicitly intended here which is:
i = (i + 1) % m
and the warning goes away.
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing 'FirmwareVersion' attribute only covers the DSP firmware as
provided by Conexant; not the overall version of the device firmware. We
do want to be able to see the full version number too.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed <module>-objs to <module>-y in Makefile.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Stanse found that ia_init_one locks a spinlock and inside of that it
calls ia_start which calls:
* request_irq
* tx_init which does kmalloc(GFP_KERNEL)
Both of them can thus sleep and result in a deadlock. I don't see a
reason to have a per-device spinlock there which is used only there
and inited right before the lock location. So remove it completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found we do in console_show:
kfree_skb(skb);
return skb->len;
which is not good. Fix that by remembering the len and use it in the
function instead.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code does not call deinit_card(card); in an error case, as done in
other error-handling code in the same function. But actually, the called
function init_sram can only return 0, so there is no need for the error
check at all.
init_sram is also given a void return type, and its single return statement
at the end of the function is dropped.
A simplified version of the sematic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
@r@
statement S1,S2,S3;
constant C1,C2,C3;
@@
*if (...)
{... S1 return -C1;}
...
*if (...)
{... when != S1
return -C2;}
...
*if (...)
{... S1 return -C3;}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Cc: linux-atm-general@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
The function has an unsigned return type, but returns a negative constant
to indicate an error condition. The result of calling the function is
always stored in a variable of type (signed) int, and thus unsigned can be
dropped from the return type.
A sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@exists@
identifier f;
constant C;
@@
unsigned f(...)
{ <+...
* return -C;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indent the branch of an if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (59 commits)
igbvf.txt: Add igbvf Documentation
igb.txt: Add igb documentation
e100/e1000*/igb*/ixgb*: Add missing read memory barrier
ixgbe: fix build error with FCOE_CONFIG without DCB_CONFIG
netxen: protect tx timeout recovery by rtnl lock
isdn: gigaset: use after free
isdn: gigaset: add missing unlock
solos-pci: Fix race condition in tasklet RX handling
pkt_sched: Fix sch_sfq vs tcf_bind_filter oops
net: disable preemption before call smp_processor_id()
tcp: no md5sig option size check bug
iwlwifi: fix locking assertions
iwlwifi: fix TX tracer
isdn: fix information leak
net: Fix napi_gro_frags vs netpoll path
usbnet: remove noisy and hardly useful printk
rtl8180: avoid potential NULL deref in rtl8180_beacon_work
ath9k: Remove myself from the MAINTAINERS list
libertas: scan before assocation if no BSSID was given
libertas: fix association with some APs by using extended rates
...
We were seeing faults in the solos-pci receive tasklet when packets
arrived for a VCC which was currently being closed:
[18842.727906] EIP: [<e082f490>] br2684_push+0x19/0x234 [br2684] SS:ESP 0068:dfb89d14
[18845.090712] [<c13ecff3>] ? do_page_fault+0x0/0x2e1
[18845.120042] [<e082f490>] ? br2684_push+0x19/0x234 [br2684]
[18845.153530] [<e084fa13>] solos_bh+0x28b/0x7c8 [solos_pci]
[18845.186488] [<e084f711>] ? solos_irq+0x2d/0x51 [solos_pci]
[18845.219960] [<c100387b>] ? handle_irq+0x3b/0x48
[18845.247732] [<c10265cb>] ? irq_exit+0x34/0x57
[18845.274437] [<c1025720>] tasklet_action+0x42/0x69
[18845.303247] [<c102643f>] __do_softirq+0x8e/0x129
[18845.331540] [<c10264ff>] do_softirq+0x25/0x2a
[18845.358274] [<c102664c>] _local_bh_enable_ip+0x5e/0x6a
[18845.389677] [<c102666d>] local_bh_enable+0xb/0xe
[18845.417944] [<e08490a8>] ppp_unregister_channel+0x32/0xbb [ppp_generic]
[18845.458193] [<e08731ad>] pppox_unbind_sock+0x18/0x1f [pppox]
This patch uses an RCU-inspired approach to fix it. In the RX tasklet's
find_vcc() function we first refuse to use a VCC which already has the
ATM_VF_READY bit cleared. And in the VCC close function, we synchronise
with the tasklet to ensure that it can't still be using the VCC before
we continue and allow the VCC to be destroyed.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Nathan Williams <nathan@traverse.com.au>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (63 commits)
of/platform: Register of_platform_drivers with an "of:" prefix
of/address: Clean up function declarations
of/spi: call of_register_spi_devices() from spi core code
of: Provide default of_node_to_nid() implementation.
of/device: Make of_device_make_bus_id() usable by other code.
of/irq: Fix endian issues in parsing interrupt specifiers
of: Fix phandle endian issues
of/flattree: fix of_flat_dt_is_compatible() to match the full compatible string
of: remove of_default_bus_ids
of: make of_find_device_by_node generic
microblaze: remove references to of_device and to_of_device
sparc: remove references to of_device and to_of_device
powerpc: remove references to of_device and to_of_device
of/device: Replace of_device with platform_device in includes and core code
of/device: Protect against binding of_platform_drivers to non-OF devices
of: remove asm/of_device.h
of: remove asm/of_platform.h
of/platform: remove all of_bus_type and of_platform_bus_type references
of: Merge of_platform_bus_type with platform_bus_type
drivercore/of: Add OF style matching to platform bus
...
Fix up trivial conflicts in arch/microblaze/kernel/Makefile due to just
some obj-y removals by the devicetree branch, while the microblaze
updates added a new file.
Both of_bus_type and of_platform_bus_type are just #define aliases
for the platform bus. This patch removes all references to them and
switches to the of_register_platform_driver()/of_unregister_platform_driver()
API for registering.
Subsequent patches will convert each user of of_register_platform_driver()
into plain platform_drivers without the of_platform_driver shim. At which
point the of_register_platform_driver()/of_unregister_platform_driver()
functions can be removed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Cc: linux-atm-general@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate changes to upper atm layer, so userspace netmontor knows when DSL
showtime reached.
Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves SPARC architecture specific data members out of
struct of_device and into the pdev_archdata structure. The reason
for this change is to unify the struct of_device definition amongst
all the architectures. It also remvoes the .sysdata, .slot, .portid
and .clock_freq properties because they aren't actually used by
anything.
A subsequent patch will replace struct of_device entirely with struct
platform_device and the of_platform support code will share common
routines with the platform bus (but the bus instances themselves can
remain separate).
This patch also adds 'struct resources *resource' and num_resources
to match the fields defined in struct platform_device. After this
change, 'struct platform_device' can be used as a drop-in replacement
for 'struct of_platform'.
This change is in preparation for merging the of_platform_bus_type
with the platform_bus_type.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Instead of a fixed list of buffers, use the buffer pool correctly and
keep track of the outstanding buffer indexes using a fixed table.
Resolves reported HBUF_ERR's -- failures due to lack of receive buffers.
Signed-off-by: Chas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
solos-pci uses request_firmware() for firmware upgrades
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a new function to return the waitqueue of a "struct sock".
static inline wait_queue_head_t *sk_sleep(struct sock *sk)
{
return sk->sk_sleep;
}
Change all read occurrences of sk_sleep by a call to this function.
Needed for a future RCU conversion. sk_sleep wont be a field directly
available.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replaces (skb->len - skb->data_len) occurrences by skb_headlen(skb)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Replace open-coded loop with for_each_set_bit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
sizeof(TstSchedTbl) is just the size of the pointer. Change it to the size
of the referenced data.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
due to reference counting sk_wmem_alloc now has a value of 1 when all
the outstanding data has been sent.
Signed-off-by: Chas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/atm/solos-pci.c: In function 'flash_upgrade':
drivers/atm/solos-pci.c:528: warning: 'fw_name' may be used uninitialized in this function
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: Nathan Williams <nathan@traverse.com.au>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables are unsigned so the `< 0' test always fails, the
other part of the test catches wrapped values.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides safety against negative optlen at the type
level instead of depending upon (sometimes non-trivial)
checks against this sprinkled all over the the place, in
each and every implementation.
Based upon work done by Arjan van de Ven and feedback
from Linus Torvalds.
Signed-off-by: David S. Miller <davem@davemloft.net>
The prefix decrement causes a very long loop if pci_pool_alloc() failed
in the first iteration. Also I swapped rbps and rbpl arguments.
Reported-by: Juha Leppanen <juha_motorsportcom@luukku.com>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
he_dev->rbps_virt or he_dev->rbpl_virt allocation may fail, s
them. Make sure that he_init_group() cleans up after errors.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression x,__divisor;
@@
- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
str has already been tested. It seems that this test should be on the
recently returned value snr.
A simplified version of the semantic match that finds this problem is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E;
@@
if (x == NULL || ...) { ... when forall
return ...; }
... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\)
(
*x == NULL
|
*x != NULL
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
InterleaveRDn and InterleaveRUp only apply to G.dmt. The equivalents for ADSL2
and 2+ are BisRDn and BisRUp. In addition, the INPdown and INPup statuses are
useful when trying to track down instability on a line.
Signed-off-by: Simon Farnsworth <simon@farnz.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is the second go through of the old DMA_nBIT_MASK macro,and there're not
so many of them left,so I put them into one patch.I hope this is the last round.
After this the definition of the old DMA_nBIT_MASK macro could be removed.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes there can be received packets with the size field set to 0xFFFF.
This seems to only occur after an FPGA or firmware upgrade.
This patch discards packets with an invalid size.
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Buffer sizes have been changed to 2048 bytes.
Flash upgrades use a dedicated RAM block.
Add support for daughterboard.
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Change printk() argument to fix compiler warning.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fore 200 ATM driver fails to handle request_firmware failures and oopses
when no firmware file was found. Fix it by checking for the right return
values and propaganting the return value up.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
I don't much like the trick with multiple inclusions of solos-attrlist.c
but don't really see a saner way to do it without repeating the list.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There are still a _lot_ of attributes, but for at least the basic ones
we want to be able to get/set them from the kernel. Especially the ones
we want to inform the ATM core about (link state, speed).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We no longer try to load firmware while the ATM is up and running.
However, this means that we _do_ make init_module() wait for it, and it
takes a long time for now (since we're using ultra-conservative code in
the FPGA for that too).
The inner loop which uses swahb32p() was by Simon Farnsworth.
Simon has patches which migrate us to request_firmware_nowait(), for
which we'll actually need to take down the ATM devices, do the upgrade,
then reregister them.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is just a straight pull in of changes, syncing us up to 0.07 from
openadsl.sf.net
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: Simon Farnsworth <simon@farnz.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Print a message if pskb_expand_head fails.
Make atmdebug writable by root, so that you can turn printing of data sent to
and received from the card on and off at runtime - useful for tracking
corruption.
Signed-off-by: Simon Farnsworth <simon@farnz.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The length field shouldn't ever include the size of the header itself.
This fixes the problem that some people were seeing with 1500-byte
packets.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In preparation for the introduction of a generic swap() macro.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds basic support for the 'Solos' PCI ADSL2+ cards being developed
by Traverse Technologies and Xrio Ltd:
http://www.traverse.com.au/productview.php?product_id=116
Signed-off-by: Nathan Williams <nathan@traverse.com.au>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One fail path in hrz_probe omitted device disable. Fix it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
In the case of the file drivers/atm/eni.c, I am a little bit suspicious of
the -1 at the end of the affected expression. Please check that that is
what is wanted.
An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression n,d;
@@
(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in preparation for the subsequent asm/sbus.h removal.
Also, make these routines take a "struct device" or no
arguments, as appropriate.
Signed-off-by: David S. Miller <davem@davemloft.net>
And all the SBUS dma interfaces are deleted.
A private implementation remains inside of the 32-bit sparc port which
exists only for the sake of the implementation of dma_*().
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix direct casts of pointers to u32 in the InterPhase ATM driver. These are
all arguments being passed to printk() calls. So drop the cast and change the
%x to a %p.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it had various regions to be loaded to separate addresses, and it
wanted to do them in fairly small chunks anyway, switch it to use the
new ihex code. Encode the start address in the first record.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
This fixes the most obvious 64-bit problems, but it is still very very
broken in other aspects.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
This causes the suni driver to oops if you try to use sonetdiag to get
the statistics. Also add the corresponding phy->stop call to fix another
oops if you try to remove the module.
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Kroah-Hartman