Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the usage of CLK_IS_BASIC flag completely from TI clock driver.
In most cases, the use is completely redundant, but in some cases
we need to use the new API to check if the clock is an OMAP clock or not.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Currently, TI clock driver uses an encapsulated struct that is cast into
a void pointer to store all register addresses. This can be considered
as rather nasty hackery, and prevents from expanding the register
address field also. Instead, replace all the code to use proper struct
in place for this, which contains all the previously used data.
This patch is rather large as it is touching multiple files, but this
can't be split up as we need to avoid any boot breakage.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The OMAP36xx DPLL5, driving EHCI USB, can be subject to a long-term
frequency drift. The frequency drift magnitude depends on the VCO update
rate, which is inversely proportional to the PLL divider. The kernel
DPLL configuration code results in a high value for the divider, leading
to a long term drift high enough to cause USB transmission errors. In
the worst case the USB PHY's ULPI interface can stop responding,
breaking USB operation completely. This manifests itself on the
Beagleboard xM by the LAN9514 reporting 'Cannot enable port 2. Maybe the
cable is bad?' in the kernel log.
Errata sprz319 advisory 2.1 documents PLL values that minimize the
drift. Use them automatically when DPLL5 is used for USB operation,
which we detect based on the requested clock rate. The clock framework
will still compute the PLL parameters and resulting rate as usual, but
the PLL M and N values will then be overridden. This can result in the
effective clock rate being slightly different than the rate cached by
the clock framework, but won't cause any adverse effect to USB
operation.
Signed-off-by: Richard Watts <rrw@kynesim.co.uk>
[Upported from v3.2 to v4.9]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Convert DPLL support code to use clk_hw pointers for reference and bypass
clocks. This allows us to use clk_hw_* APIs for accessing any required
parameters for these clocks, avoiding some locking problems at least with
DPLL enable code; this used clk_get_rate which uses mutex but isn't
good under clk_enable / clk_disable.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
As the code in this file is being executed within irq context in some
cases, we must avoid the clk_get_rate which uses mutex internally.
Switch the code to use clk_hw_get_rate instead which is non-locking.
This fixes an issue where PM runtime will hang the system if enabled
with a serial console before a suspend-resume cycle.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Fixes: a53ad8ef3d ("clk: ti: Convert to clk_hw based provider APIs")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Errata i810 states that DPLL controller can get stuck while transitioning
to a power saving state, while its M/N ratio is being re-programmed.
As a workaround, before re-programming the M/N ratio, SW has to ensure
the DPLL cannot start an idle state transition. SW can disable DPLL
idling by setting the DPLL AUTO_DPLL_MODE=0 or keeping a clock request
active by setting a dependent clock domain in SW_WKUP.
This errata impacts OMAP5 and DRA7 chips, so enable the errata for these.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Mostly converted with the following snippet:
@@
struct clk_hw *E;
@@
-__clk_get_flags(E->clk)
+clk_hw_get_flags(E)
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
From Tero Kristo:
"This pull request contains the TI clock driver set to move the
clock implementations under clock driver. Some small portions of
the clock driver code still remain under mach-omap2 after this,
it should be decided whether this code is now obsolete and should
be deleted or should someone try to fix it."
Slight merge conflicts with determine_rate prototype changes.
With the legacy clock support gone, OMAP3 generic DPLL code can now be
moved over to the clock driver also. A few un-unused clkoutx2 functions
are also removed at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Thomas Gleixner