The maximum timeout to wait for the PRCM to request that a module
exit idle or reach functionnal state is common to OMAP2/3/4 SoCs,
so, move it to the chip family-common cm.h include file.
Reduce the timeout from 20 ms to 2 ms.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 678bc9a2ea split dpll4_m2_ck,
creating a 34xx and a 36xx variant, to handle the additional 16
divider steps provided on the 36xx. This in turn required dynamic
rewriting of the clock tree during initialization, which is
undesirable. All this seems to be unnecessary, though, since the
additional 16 divider steps can simply be marked with RATE_IN_36XX.
This patch does so and re-merges the affected structures.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Vishwanath Sripathy <vishwanath.bs@ti.com>
Rename the RATE_IN_343X clksel_rate.rate flag to be RATE_IN_3XXX, to reflect
that these rates are valid on all OMAP3 platforms, not just 343X.
Also rename the RATE_IN_OMAP3430ES2 clksel_rate.rate flag to be
RATE_IN_OMAP3430ES2PLUS, to reflect that these flags are valid on all
OMAP3 platforms after 3430ES2.
This patch should not result in any functional changes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
This patch cleans up arch/arm/mach-omap2/clkt_clksel.c. It:
- makes several functions static that are not called outside the file;
- adds documentation;
- makes some code paths easier to read (hopefully), by breaking up
compound statements and removing redundant checks;
- converts some pr_err()s that indicate clock tree data problems into WARN()s,
so they are more likely to be noticed;
- and moves omap2_clk_round_rate() back into mach-omap2/clock.c, its proper
home, since it is not clksel-specific.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The DEFAULT_RATE clksel_rate flag is essentially useless. It was set
on some of the lowest divisors, which, when switching to a much
higher-rate parent, could have potentially resulted in rates that
exceeded the hardware specifications for downstream clocks in the
window between the clk_set_parent(), and a subsequent clk_set_rate().
It seems much safer to just remove the flag and always use the highest
available divisor (resulting in the lowest possible rate) after the
switch, and this patch does so.
Ideally, it would be best to first attempt to switch to a divisor that
matches the clock's rate with the previous parent, if at all possible.
But that is a project for some other day or some other person. The
parent changing code is rarely used.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Writes to the PM_*GRPSEL registers should use _GRPSEL_ macros, not _EN_ macros,
to match the TRM and guard against inadvertent error. This patch should
not cause any functional change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jouni Högander <jouni.hogander@nokia.com>
Fix all of the remaining PRCM register shift/bitmask macros that did not
use the _SHIFT/_MASK suffixes to use them. This makes the use of these
macros consistent. It is intended to reduce error, as code can be inspected
visually by reviewers to ensure that bitshifts and bitmasks are used in
the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Fix all of the remaining OMAP3 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them. This makes the use
of these macros consistent. It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Fix all of the remaining OMAP2 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them. This makes the use
of these macros consistent. It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
There are three i2c buses on am3517, and each i2c bus has several devices
on it, so we can't name the i2c boardinfo structures with one of these
devices. In order to make it more readable, now rename these three boardinfo
structures based on i2c indexes.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Acked-By: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves OMAP4 soc specific code from 4430sdp board file.
The change is necessary so that newer board support can be added
with minimal changes. This will be also problematic for
multi-board, multi-omap builds.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3517 don't have the register OMAP343X_CONTROL_PBIAS_LITE and the regulators
like "vmmc", so we set a noop "set_power" function for it.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is two gpio for mmc use, one is for card detecting, another is
used for checking write protect. Intialize its pinmux in case the bootloader
doesn't set it.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SDI Display subsystem needs access to the vdds_sdi supply
regulator. This is TWL4030's VAUX1 supply on RX-51.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
EHCI port on UI card and LCD share two pins (GPIO 181 and 182) thus
they have to be mutually exclusive.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upcoming change to tlv320aic3x codec driver require four supplies.
Implement this by connecting analogic supplies to TWL4030 VMMC2 and digital
supplies to TWL4030 VIO.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes possible to probe the audio codec and add another i2c2
components in the future.
Fix also indentation for the first omap_register_i2c_bus.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I believe the VMMC2 constraints must be the same than with VAUX3. Older
boards are using TWL4030 VMMC2 supply for internal MMC whereas newer are
using VAUX3 that has more limited constraints defined in this same file.
More over, the VMMC2 supply is used also for analog audio domain and the
miminum analog voltage of the TLV320AIC34 codec is 2.7 V.
To combine these two facts, the patch changes supply name to V28_A as the
newer boards register VMMC2_30 for VAUX3 and uses the same constraints than
VAUX3 since those constraints are ok for the TLV320AIC34.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some Overo add-on boards include a second ethernet port. This patch
adds support for that second port.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The emac driver currently uses Davinci clock names for the module and phy
clocks. Updated the omap3xxx_clks table to match the names
used by the Davinci emac driver.
Note that eventually the EMAC clocks should be renamed to be generic.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated patch description to match the patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Configuration for OMAP2430 should select ARCH_OMAP_OTG just like
it is done for OMAP2420
Signed-off-by: Viral Mehta <viral.mehta@lntinfotech.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform init code for OHCI USB on OMAP2430 SDP
Signed-off-by: Viral Mehta <viral.mehta@lntinfotech.com>
[tony@atomide.com: Updated subject to mention the board name]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds TLB preservation support to IOMMU module
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This patch provides the iommu support for OMAP4 co-processors.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This patch includes changes to omap3-iommu.c file to make it generic
for all OMAPs. Renamed omap3-iommu.c to omap-iommu.c
[Hiroshi DOYU: Remove unnecessary "iommu-y" in Makefile]
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Currently, the GPIO 'prepare' hook is only called when going to
off-mode, while the function is called 'prepare_for_retention.' This
patch renames the function to 'prepare_for_idle' and calls it for any
powersate != PWRDM_POWER_ON passing in the powerstate.
The hook itself is then responsible for doing various preparation
based on the powerstate.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Off mode is now using the omap2 retention fix code for scanning GPIOs
during off-mode transitions. All the *non_wakeup_gpios variables
are now used for off-mode transition tracking on OMAP3. This patch fixes
cases where GPIO state changes are missed during off-mode.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
We can remove this wakeup dependency since now, when
GPIO2-6 are enabled for IO-pad wakeup, PER domain is gauranteed
to be awake or be woken up to service.
The previous dependency did not handle all corner cases. Since there
was no sleep dependency between CORE and PER domains, if PER enters
RET and CORE is ON, PER will not be active for GPIO handling.
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
IO events can also come from GPIO modules, which reside in the PER domain.
It is possible for the PER to enter RET while CORE is still in ON.
If GPIO 2-6 are enabled for IO-pad wakeups, the PER domain will not
wakeup in this case, unless we enable it.
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch enables the wakeup capabilities of ads7846 touchscreen driver.
ads7846 driver can now wakeup the system from suspend on OMAP3430 EVM
and SDP boards.
The earlier approach of enabling wakeup on the touchscreen GPIO pin during
board level mux init is removed. Instead the wakeup flag in
ads7846_platform_data is enabled. Based on the flag, the ads7846 driver
will do an enable_irq_wake which will eventually call into the OMAP GPIO
layer and will enable the wakeup capability on the GPIO pin.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP3530 TRM section 7.4.4.4.2 requires OFFOUTENABLE to be set (active low)
if wakeup capabilities are enabled on a pad. During OFF mode testing
on OMAP3530 EVM, it was observed that the device was not residing in
the OFF state. The device enters into the OFF state and immediately exits
from that state as if an IO wakeup event has occured. The issue was traced
down to the pad configuration of wkaeup enabled pad's.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Millisecond resolution is possible and there are use cases for it
(automatic testing).
Seconds-based interface is preserved for compatibility.
Signed-off-by: Ari Kauppi <Ext-Ari.Kauppi@nokia.com>
Reviewed-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
While handling PRCM IRQs, mask out interrupts that are not enabled in
PRM_IRQENABLE_MPU. If these are not masked out, non-enabled
interrupts are caught, a WARN() is printed due to no 'handler' and the
events are cleared. In addition to being noisy, this can also
interfere with independent polling of this register by SR/VP code.
This was noticed using SmartReflex transitions which cause the VPx_*
interrupts to be handled since they are set in PRM_IRQSTATUS_MPU even
but not enabled in PRM_IRQENABLE_MPU.
Acked-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
These are currently non-muxable, so let's save some memory
and remove them. Otherwise we get the following warnings:
mux: Unknown ball offset 0x5e
mux: Unknown ball offset 0x60
mux: Unknown ball offset 0x62
...
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we can get the following error:
error: variable 'tdo24m_mcspi_config' has initializer but incomplete type
...
Signed-off-by: Tony Lindgren <tony@atomide.com>
Zoom2 and 3 have UARTs only on the external debug board.
GPMC needs to be mapped early to use it for DEBUG_LL.
Additionally, 0xfb000000 overlaps with other areas, so
use 0xfa400000 for the virtual address instead.
Note that with the pending serial.c patches you need to
set console=ttyS0,115200n8 as it will be the only UART
mapped. To use DEBUG_LL, you need to pass also earlyprintk
in cmdline.
Cc: Allen Pais <allen.pais@ti.com>
Acked-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This removes the dependency to the UART1 being available for storing
the debug configuration in uncompress.h. This will simplify the
DEBUG_LL UART configuration for boards that may not have UART1, or
have an external UART as it requires only one mapping for DEBUG_LL.
The patch has a few limitations. Basically now we're assuming that
the kernel uncompress code won't overlap with OMAP_UART_INFO. We also
assume the printascii is called at least once before paging_init in
order for addruart to have a chance to read the UART setup from
OMAP_UART_INFO.
As suggested by Cyril Chemparathy <cyril@ti.com>,
Vikram Pandita <vikram.pandita@ti.com> and
Kevin Hilman <khilman@deeprootsystems.com>. Based on an earlier
patch posted for Davinci by Cyril Chemparathy <cyril@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (39 commits)
omap: delete unused bootloader tag variables
omap: Devkit8000: Remove unused pins
omap: Devkit8000: Change position of init calls
omap: Devkit8000: Remove unnecessary include file
omap: Devkit8000: Fix typo in pin name
omap: Devkit8000: Add missing package selection
omap: Devkit8000: Fix typo in supplies
n8x0_defconfig: remove CONFIG_NILFS2_FS override
omap: board-sdp-flash.c: Fix typos in debug output
omap4: Fix McBSP4 base address
omap: rx51_defconfig: Remove CONFIG_SYSFS_DEPRECATED*=y options
omap: rx51_defconfig: Remove duplicate phonet
omap: fix a gpmc nand problem
AM3517: initialize i2c subsystem after mux subsystem
omap: remove one of the define of INT_34XX_BENCH_MPU_EMUL
omap: fix the compile error if CONFIG_MTD_NAND_OMAP2 is notenabled
OMAP4: Clocks: Change SPI Instance Names
omap: Devkit8000: Fix wrong usb port on Devkit8000
OMAP4: Fix for CONTROL register Base
OMAP4-HSMMC: FIX for MMC5 Controller IRQ Base
...
Benoit Cousson