Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
This patch allows the 1-wire bus to autoload the corresponding module
for each slave being attached.
This works similar to bluetooth protocols.
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for maxim ds1825 based 1-wire temperature sensors.
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michael Neuling <mikey@neuling.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix obvious cases of "it's" being used when "its" was meant.
Signed-off-by: Francis Galiegue <fgaliegue@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no point in implementing a detect callback for the DS2482, as
this device can't be detected. It was there solely to handle "force"
module parameters to instantiate devices, but now we have a better sysfs
interface that can do the same.
So we can get rid of the ugly module parameters and the detect callback.
This shrinks the binary module size by 21%.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Gardner <gardner.ben@gmail.com>
Send completion status of the commands to the userspace. Message and
protocol are described in the documentation.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Command which allows to reset the bus.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Paul Alfille <paul.alfille@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the 1-wire master interface for i.MX27 and
i.MX31.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide some additional details about the status of the driver and the
ds2490 hardware.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added strong pullup to thermal sensor driver and general documentation on
the sensor.
Signed-off-by: David Fries <david@fries.net>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a GPIO 1-wire bus master driver. The driver used the GPIO API to
control the wire and the GPIO pin can be specified using platform data
similar to i2c-gpio. The driver was tested with AT91SAM9260 + DS2401.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are three types of messages between w1 core and userspace:
1. Events. They are generated each time new master or slave device found
either due to automatic or requested search.
2. Userspace commands. Includes read/write and search/alarm search comamnds.
3. Replies to userspace commands.
From: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Special file in each w1 slave device's directory called "rw" is created
each time new slave and no appropriate w1 family is registered.
"rw" file supports read and write operations, which allows to perform
almost any kind of operations. Each logical operation is a transaction
in nature, which can contain several (two or one) low-level operations.
Let's see how one can read EEPROM context:
1. one must write control buffer, i.e. buffer containing command byte
and two byte address. At this step bus is reset and appropriate device
is selected using either W1_SKIP_ROM or W1_MATCH_ROM command.
Then provided control buffer is being written to the wire.
2. reading. This will issue reading eeprom response.
It is possible that between 1. and 2. w1 master thread will reset bus for
searching and slave device will be even removed, but in this case 0xff will
be read, since no device was selected.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Linus Torvalds