Support the next generation Intel Atom processor
mirco-architecture, formerly called Silvermont.
The server version, formerly called "Avoton",
is named the "Intel(R) Atom(TM) Processor C2000 Product Family".
The client version, formerly called "Bay Trail",
is named the "Intel Atom Processor Z3000 Series",
as well as various "Intel Pentium Processor"
and "Intel Celeron Processor" brands, depending
on form-factor.
Silvermont has a set of MSRs not far off from NHM,
but the RAPL register set is a sub-set of those previously supported.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This specific processor supports 3 new package sleep states.
Provide a monitor, so that the user can see their usage.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add Haswell model numbers to snb_register() as it also supports the
C-states introduced in SandyBridge processors.
[rjw: Changelog]
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Example:
cpupower idle-set -d 3
will disable C-state 3 on all processors (set commands are active on
all CPUs by default), same as:
cpupower -c all idle-set -d 3
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Latest kernel allows to disable C-states via:
/sys/devices/system/cpu/cpuX/cpuidle/stateY/disable
This patch provides lower level sysfs access functions to make use of
this interface. A later patch will implement the higher level stuff.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use unsigned int as the data type for some variables related to CPU
idle states which allows the code to be simplified slightly.
[rjw: Changelog]
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On platforms with C8-C10 support, the additional C-states cause
turbostat to overrun its output buffer of 128 bytes per CPU. Increase
this to 256 bytes per CPU.
[ As a bugfix, this should go into 3.10; however, since the C8-C10
support didn't go in until after 3.9, this need not go into any stable
kernel. ]
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull idle update from Len Brown:
"Add support for new Haswell-ULT CPU idle power states"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
intel_idle: initial C8, C9, C10 support
tools/power turbostat: display C8, C9, C10 residency
Display residency in the new C-states, C8, C9, C10.
C8, C9, C10 are present on some:
"Fourth Generation Intel(R) Core(TM) Processors",
which are based on Intel(R) microarchitecture code name Haswell.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Correct spelling typos in various part of printk.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The SMI counter is popular -- so display it by default
rather than requiring an option. What the heck,
we've blown the 80 column budget on many systems already...
Note that the value displayed is the delta
during the measurement interval.
The absolute value of the counter can still be seen with
the generic 32-bit MSR option, ie. -m 0x34
Signed-off-by: Len Brown <len.brown@intel.com>
When verbose is enabled, print the C1E-Enable
bit in MSR_IA32_POWER_CTL.
also delete some redundant tests on the verbose variable.
Signed-off-by: Len Brown <len.brown@intel.com>
This patch enables turbostat to run properly on the
next-generation Intel(R) Microarchitecture, code named "Haswell" (HSW).
HSW supports the BCLK and counters found in SNB.
Signed-off-by: Len Brown <len.brown@intel.com>
Change the default location to install acpidump into from /usr/bin
to /usr/sbin, as this tool needs to be run as root.
[rjw: Subject and changelog]
Signed-off-by: Thomas Renninger <trenn@suse.de>
Tested-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull powertool update from Len Brown:
"This updates the tree w/ the latest version of turbostat, which
reports temperature and - on SNB and later - Watts."
Fix up semantic merge conflict as per Len.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools: Allow tools to be installed in a user specified location
tools/power: turbostat: make Makefile a bit more capable
tools/power x86_energy_perf_policy: close /proc/stat in for_every_cpu()
tools/power turbostat: v3.0: monitor Watts and Temperature
tools/power turbostat: fix output buffering issue
tools/power turbostat: prevent infinite loop on migration error path
x86 power: define RAPL MSRs
tools/power/x86/turbostat: share kernel MSR #defines
When building x86_energy_perf_policy or turbostat within the confines of
a packaging system such as RPM, we need to be able to have it install to
the buildroot and not the root filesystem of the build machine. This
adds a DESTDIR variable that when set will act as a prefix for the
install location of these tools.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The turbostat Makefile is pretty simple, its output is placed in the
same directory as the source, the install rule has no concept of a
prefix or sysroot, and you can set CC to use a specific compiler but
not use the more familiar CROSS_COMPILE. By making a few minor changes
these limitations are removed while leaving the default behavior
matching what it used to be.
Example build with these changes:
make CROSS_COMPILE=i686-wrs-linux-gnu- DESTDIR=/tmp install
or from the tools directory
make CROSS_COMPILE=i686-wrs-linux-gnu- DESTDIR=/tmp turbostat_install
Signed-off-by: Mark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Instead of returning out of for_every_cpu() we should break out of the loop=
which will then tidy up correctly by closing the file /proc/stat.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Show power in Watts and temperature in Celsius
when hardware support is present.
Intel's Sandy Bridge and Ivy Bridge processor generations support RAPL
(Run-Time-Average-Power-Limiting). Per the Intel SDM
(Intel® 64 and IA-32 Architectures Software Developer Manual)
RAPL provides hardware energy counters and power control MSRs
(Model Specific Registers). RAPL MSRs are designed primarily
as a method to implement power capping. However, they are useful
for monitoring system power whether or not power capping is used.
In addition, Turbostat now shows temperature from DTS
(Digital Thermal Sensor) and PTM (Package Thermal Monitor) hardware,
if present.
As before, turbostat reads MSRs, and never writes MSRs.
New columns are present in turbostat output:
The Pkg_W column shows Watts for each package (socket) in the system.
On multi-socket systems, the system summary on the 1st row shows the sum
for all sockets together.
The Cor_W column shows Watts due to processors cores.
Note that Core_W is included in Pkg_W.
The optional GFX_W column shows Watts due to the graphics "un-core".
Note that GFX_W is included in Pkg_W.
The optional RAM_W column on server processors shows Watts due to DRAM DIMMS.
As DRAM DIMMs are outside the processor package, RAM_W is not included in Pkg_W.
The optional PKG_% and RAM_% columns on server processors shows the % of time
in the measurement interval that RAPL power limiting is in effect on the
package and on DRAM.
Note that the RAPL energy counters have some limitations.
First, hardware updates the counters about once every milli-second.
This is fine for typical turbostat measurement intervals > 1 sec.
However, when turbostat is used to measure events that approach
1ms, the counters are less useful.
Second, the 32-bit energy counters are subject to wrapping.
For example, a counter incrementing 15 micro-Joule units
on a 130 Watt TDP server processor could (in theory)
roll over in about 9 minutes. Turbostat detects and handles
up to 1 counter overflow per measurement interval.
But when the measurement interval exceeds the guaranteed
counter range, we can't detect if more than 1 overflow occured.
So in this case turbostat indicates that the results are
in question by replacing the fractional part of the Watts
in the output with "**":
Pkg_W Cor_W GFX_W
3** 0** 0**
Third, the RAPL counters are energy (Joule) counters -- they sum up
weighted events in the package to estimate energy consumed. They are
not analong power (Watt) meters. In practice, they tend to under-count
because they don't cover every possible use of energy in the package.
The accuracy of the RAPL counters will vary between product generations,
and between SKU's in the same product generation, and with temperature.
turbostat's -v (verbose) option now displays more power and thermal configuration
information -- as shown on the turbostat.8 manual page.
For example, it now displays the Package and DRAM Thermal Design Power (TDP):
cpu0: MSR_PKG_POWER_INFO: 0x2f064001980410 (130 W TDP, RAPL 51 - 200 W, 0.045898 sec.)
cpu0: MSR_DRAM_POWER_INFO,: 0x28025800780118 (35 W TDP, RAPL 15 - 75 W, 0.039062 sec.)
cpu8: MSR_PKG_POWER_INFO: 0x2f064001980410 (130 W TDP, RAPL 51 - 200 W, 0.045898 sec.)
cpu8: MSR_DRAM_POWER_INFO,: 0x28025800780118 (35 W TDP, RAPL 15 - 75 W, 0.039062 sec.)
Signed-off-by: Len Brown <len.brown@intel.com>
In periodic mode, turbostat writes to stdout,
but users were un-able to re-direct stdout, eg.
turbostat > outputfile
would result in an empty outputfile.
Signed-off-by: Len Brown <len.brown@intel.com>
If an MSR based monitor is run in parallel this is not needed. This is the
default case on all/most Intel machines.
But when only sysfs info is read via cpupower monitor -m Idle_Stats (typically
the case for non root users) or when other monitors are PCI based (AMD),
Idle_Stats, read from sysfs can be totally bogus:
cpupower monitor -m Idle_Stats
PKG |CORE|CPU | POLL | C1-N | C3-N | C6-N
0| 0| 0| 0.00| 0.00| 0.24| 99.81
0| 0| 32| 0.00| 0.00| 0.00| 100.7
...
0| 17| 20| 0.00| 0.00| 0.00| 173.1
0| 17| 52| 0.00| 0.00| 0.07| 173.0
0| 18| 68| 0.00| 0.00| 0.00| 0.00
0| 18| 76| 0.00| 0.00| 0.00| 0.00
...
With the -c option all cores are woken up and the kernel
did update cpuidle statistics before reading out sysfs.
This causes some overhead. Therefore avoid if possible, use
if needed:
cpupower monitor -c -m Idle_Stats
PKG |CORE|CPU | POLL | C1-N | C3-N | C6-N
0| 0| 0| 0.00| 0.00| 0.00| 100.2
0| 0| 32| 0.00| 0.00| 0.00| 100.2
...
0| 8| 8| 0.00| 0.00| 0.00| 99.82
0| 8| 40| 0.00| 0.00| 0.00| 99.81
0| 9| 24| 0.00| 0.00| 0.00| 100.3
0| 9| 56| 0.00| 0.00| 0.00| 100.2
0| 16| 4| 0.00| 0.00| 0.00| 99.75
0| 16| 36| 0.00| 0.00| 0.00| 99.38
...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The pkgs member of cpupower_topology is being used as the number of
cpu packages. As the comment in get_cpu_topology notes, the package ids
are not guaranteed to be contiguous. So, simply setting pkgs to the value
of the highest physical_package_id doesn't actually provide a count of
the number of cpu packages. Instead, calculate pkgs by setting it to
the number of distinct physical_packge_id values which is pretty easy
to do after the core_info structs are sorted. Calculating pkgs this
way also has the nice benefit of getting rid of a sign comparison warning
that GCC 4.6 was reporting.
Signed-off-by: Palmer Cox <p@lmercox.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpu_info member of cpupower_topology was being declared as an unnamed
structure. This member was then being malloced using the size of the
parent cpupower_topology * the number of cpus. This works
because cpu_info is smaller than cpupower_topology. However, there is
no guarantee that will always be the case. Making cpu_info its own
top level structure (named cpuid_core_info) allows for mallocing the actual
size of this structure. This also lets us get rid of a redefinition of
the structure in topology.c with slightly different field names.
Signed-off-by: Palmer Cox <p@lmercox.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix a variety of issues with sysfs_topology_read_file:
* The return value of sysfs_topology_read_file function was not properly
being checked for failure.
* The function was reading int valued sysfs variables and then returning
their value. So, even if a function was trying to check the return value
of this function, a caller would not be able to tell an failure code apart
from reading a negative value. This also conflicted with the comment on the
function which said that a return value of 0 indicated success.
* The function was parsing int valued sysfs values with strtoul instead of
strtol.
* The function was non-static even though it was only used in the
file it was declared in.
Signed-off-by: Palmer Cox <p@lmercox.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix minor warnings reported with GCC 4.6:
* The sysfs_write_file function is unused - remove it.
* The pr_mon_len in the print_header function is unsed - remove it.
Signed-off-by: Palmer Cox <p@lmercox.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The files generated by the Makefiles in the debug directories aren't listed
in the .gitignore file in the root of the cpupower tool which causes these
files to show up in the output of 'git status'.
Signed-off-by: Palmer Cox <p@lmercox.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The clean targets from the cpupower tools' Makefiles use brace expansion to
remove some generated files. However, the default shells on many systems do
not support this feature resulting in some generated files not being removed
by clean.
Signed-off-by: Palmer Cox <p@lmercox.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Turbostat assumed if it can't migrate to a CPU, then the CPU
must have gone off-line and turbostat should re-initialize
with the new topology.
But if turbostat can not migrate because it is restricted by
a cpuset, then it will fail to migrate even after re-initialization,
resulting in an infinite loop.
Spit out a warning when we can't migrate
and endure only 2 re-initialize cycles in a row
before giving up and exiting.
Signed-off-by: Len Brown <len.brown@intel.com>
Now that turbostat is built in the kernel tree,
it can share MSR #defines with the kernel.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
Remove duplicated include.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull kbuild fixes from Michal Marek:
"Here are two fixes I intended to send after v3.6-rc7, but failed to do
so. So please pull them for v3.7-rc1 and they will be picked up by
stable.
The first one fixes gcc -x <language> syntax in various build-time
tests, which icecream and possible other gcc wrappers did not
understand (and yes, icecream is going to be fixed as well).
The second one fixes make tar-pkg so that unpacking the tarball does
not replace the /lib -> /usr/lib symlink on recent Fedora releases."
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Fix gcc -x syntax
kbuild: Do not package /boot and /lib in make tar-pkg
Counting SMIs is popular, so add a dedicated "-s" option to do it,
and juggle some of the other option letters.
-S is now system summary (was -s)
-c is 32 bit counter (was -d)
-C is 64-bit counter (was -D)
-p is 1st thread in core (was -c)
-P is 1st thread in package (was -p)
bump the minor version number
Signed-off-by: Len Brown <len.brown@intel.com>
The correct syntax for gcc -x is "gcc -x assembler", not
"gcc -xassembler". Even though the latter happens to work, the former
is what is documented in the manual page and thus what gcc wrappers
such as icecream do expect.
This isn't a cosmetic change. The missing space prevents icecream from
recognizing compilation tasks it can't handle, leading to silent kernel
miscompilations.
Besides me, credits go to Michael Matz and Dirk Mueller for
investigating the miscompilation issue and tracking it down to this
incorrect -x parameter syntax.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Cc: Bernhard Walle <bernhard@bwalle.de>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
# turbostat -d 0x34
is useful for printing the number of SMI's within an interval
on Nehalem and newer processors.
where
# turbostat -m 0x34
will simply print out the total SMI count since reset.
Suggested-by: Andi Kleen
Signed-off-by: Len Brown <len.brown@intel.com>
The -M option dumps the specified 64-bit MSR with every sample.
Previously it was output at the end of each line.
However, with the v2 style of printing, the lines are now staggered,
making MSR output hard to read.
So move the MSR output column to the left where things are aligned.
Signed-off-by: Len Brown <len.brown@intel.com>
The "turbo-limit" is the maximum opportunistic processor
speed, assuming no electrical or thermal constraints.
For a given processor, the turbo-limit varies, depending
on the number of active cores. Generally, there is more
opportunity when fewer cores are active.
Under the "-v" verbose option, turbostat would
print the turbo-limits for the four cases
of 1 to 4 cores active.
Expand that capability to cover the cases of turbo
opportunities with up to 16 cores active.
Note that not all hardware platforms supply this information,
and that sometimes a valid limit may be specified for
a core which is not actually present.
Signed-off-by: Len Brown <len.brown@intel.com>
This is unchanged version 20101221, plus a small bit in
DEFINE_ALTERNATE_TYPES to enable building with latest kernel headers.
This version finds dynamic tables exported by Linux in
/sys/firmware/acpi/tables/dynamic
Signed-off-by: Yakui Zhao <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown