Add core infrastructure to support I3C in Linux and document it.
This infrastructure adds basic I3C support. Advanced features will be
added afterwards.
There are a few design choices that are worth mentioning because they
impact the way I3C device drivers can interact with their devices:
- all functions used to send I3C/I2C frames must be called in
non-atomic context. Mainly done this way to ease implementation, but
this is not set in stone, and if anyone needs async support, new
functions can be added later on.
- the bus element is a separate object, but it's tightly coupled with
the master object. We thus have a 1:1 relationship between i3c_bus
and i3c_master_controller objects, and if 2 master controllers are
connected to the same bus and both exposed to the same Linux instance
they will appear as two distinct busses, and devices on this bus will
be exposed twice.
- I2C backward compatibility has been designed to be transparent to I2C
drivers and the I2C subsystem. The I3C master just registers an I2C
adapter which creates a new I2C bus. I'd say that, from a
representation PoV it's not ideal because what should appear as a
single I3C bus exposing I3C and I2C devices here appears as 2
different buses connected to each other through the parenting (the
I3C master is the parent of the I2C and I3C busses).
On the other hand, I don't see a better solution if we want something
that is not invasive.
Missing features:
- I3C HDR modes are not supported
- no support for multi-master and the associated concepts (mastership
handover, support for secondary masters, ...)
- I2C devices can only be described using DT because this is the only
use case I have. However, the framework can easily be extended with
ACPI and board info support
- I3C slave framework. This has been completely omitted, but shouldn't
have a huge impact on the I3C framework because I3C slaves don't see
the whole bus, it's only about handling master requests and generating
IBIs. Some of the struct, constant and enum definitions could be
shared, but most of the I3C slave framework logic will be different
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Split scsi_common.o out of SCSI so that non-SCSI users can pull it in
easily for future sense buffer helper usage.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a new subsystem for GNSS (e.g. GPS) receivers.
While GNSS receivers are typically accessed using a UART interface they
often also support other I/O interfaces such as I2C, SPI and USB, while
yet other devices use iomem or even some form of remote-processor
messaging (rpmsg).
The new GNSS subsystem abstracts the underlying interface and provides a
new "gnss" class type, which exposes a character-device interface (e.g.
/dev/gnss0) to user space. This allows GNSS receivers to have a
representation in the Linux device model, something which is important
not least for power management purposes.
Note that the character-device interface provides raw access to whatever
protocol the receiver is (currently) using, such as NMEA 0183, UBX or
SiRF Binary. These protocols are expected to be continued to be handled
by user space for the time being, even if some hybrid solutions are also
conceivable (e.g. to have kernel drivers issue management commands).
This will still allow for better platform integration by allowing GNSS
devices and their resources (e.g. regulators and enable-gpios) to be
described by firmware and managed by kernel drivers rather than
platform-specific scripts and services.
While the current interface is kept minimal, it could be extended using
IOCTLs, sysfs or uevents as needs and proper abstraction levels are
identified and determined (e.g. for device and feature identification).
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ttq9
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- skip AER driver error recovery callbacks for correctable errors
reported via ACPI APEI, as we already do for errors reported via the
native path (Tyler Baicar)
- fix DPC shared interrupt handling (Alex Williamson)
- print full DPC interrupt number (Keith Busch)
- enable DPC only if AER is available (Keith Busch)
- simplify DPC code (Bjorn Helgaas)
- calculate ASPM L1 substate parameter instead of hardcoding it (Bjorn
Helgaas)
- enable Latency Tolerance Reporting for ASPM L1 substates (Bjorn
Helgaas)
- move ASPM internal interfaces out of public header (Bjorn Helgaas)
- allow hot-removal of VGA devices (Mika Westerberg)
- speed up unplug and shutdown by assuming Thunderbolt controllers
don't support Command Completed events (Lukas Wunner)
- add AtomicOps support for GPU and Infiniband drivers (Felix Kuehling,
Jay Cornwall)
- expose "ari_enabled" in sysfs to help NIC naming (Stuart Hayes)
- clean up PCI DMA interface usage (Christoph Hellwig)
- remove PCI pool API (replaced with DMA pool) (Romain Perier)
- deprecate pci_get_bus_and_slot(), which assumed PCI domain 0 (Sinan
Kaya)
- move DT PCI code from drivers/of/ to drivers/pci/ (Rob Herring)
- add PCI-specific wrappers for dev_info(), etc (Frederick Lawler)
- remove warnings on sysfs mmap failure (Bjorn Helgaas)
- quiet ROM validation messages (Alex Deucher)
- remove redundant memory alloc failure messages (Markus Elfring)
- fill in types for compile-time VGA and other I/O port resources
(Bjorn Helgaas)
- make "pci=pcie_scan_all" work for Root Ports as well as Downstream
Ports to help AmigaOne X1000 (Bjorn Helgaas)
- add SPDX tags to all PCI files (Bjorn Helgaas)
- quirk Marvell 9128 DMA aliases (Alex Williamson)
- quirk broken INTx disable on Ceton InfiniTV4 (Bjorn Helgaas)
- fix CONFIG_PCI=n build by adding dummy pci_irqd_intx_xlate() (Niklas
Cassel)
- use DMA API to get MSI address for DesignWare IP (Niklas Cassel)
- fix endpoint-mode DMA mask configuration (Kishon Vijay Abraham I)
- fix ARTPEC-6 incorrect IS_ERR() usage (Wei Yongjun)
- add support for ARTPEC-7 SoC (Niklas Cassel)
- add endpoint-mode support for ARTPEC (Niklas Cassel)
- add Cadence PCIe host and endpoint controller driver (Cyrille
Pitchen)
- handle multiple INTx status bits being set in dra7xx (Vignesh R)
- translate dra7xx hwirq range to fix INTD handling (Vignesh R)
- remove deprecated Exynos PHY initialization code (Jaehoon Chung)
- fix MSI erratum workaround for HiSilicon Hip06/Hip07 (Dongdong Liu)
- fix NULL pointer dereference in iProc BCMA driver (Ray Jui)
- fix Keystone interrupt-controller-node lookup (Johan Hovold)
- constify qcom driver structures (Julia Lawall)
- rework Tegra config space mapping to increase space available for
endpoints (Vidya Sagar)
- simplify Tegra driver by using bus->sysdata (Manikanta Maddireddy)
- remove PCI_REASSIGN_ALL_BUS usage on Tegra (Manikanta Maddireddy)
- add support for Global Fabric Manager Server (GFMS) event to
Microsemi Switchtec switch driver (Logan Gunthorpe)
- add IDs for Switchtec PSX 24xG3 and PSX 48xG3 (Kelvin Cao)
* tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe endpoint controller
PCI: endpoint: Fix EPF device name to support multi-function devices
PCI: endpoint: Add the function number as argument to EPC ops
PCI: cadence: Add host driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe host controller
PCI: Add vendor ID for Cadence
PCI: Add generic function to probe PCI host controllers
PCI: generic: fix missing call of pci_free_resource_list()
PCI: OF: Add generic function to parse and allocate PCI resources
PCI: Regroup all PCI related entries into drivers/pci/Makefile
PCI/DPC: Reformat DPC register definitions
PCI/DPC: Add and use DPC Status register field definitions
PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error()
PCI/DPC: Remove unnecessary RP PIO register structs
PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info()
PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info()
PCI/DPC: Make RP PIO log size check more generic
PCI/DPC: Rename local "status" to "dpc_status"
PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error()
...
Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android binder
fixes, the usual handful of hyper-v updates, and lots of other smaller
driver updates.
All of these have been in linux-next for a long time, with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLuZw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynS4QCcCrPmwfD5PJwaF+q2dPfyKaflkQMAn0x6Wd+u
Gw3Z2scgjETUpwJ9ilnL
=xcQ0
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android
binder fixes, the usual handful of hyper-v updates, and lots of other
smaller driver updates.
All of these have been in linux-next for a long time, with no reported
issues"
* tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (155 commits)
char: lp: use true or false for boolean values
android: binder: use VM_ALLOC to get vm area
android: binder: Use true and false for boolean values
lkdtm: fix handle_irq_event symbol for INT_HW_IRQ_EN
EISA: Delete error message for a failed memory allocation in eisa_probe()
EISA: Whitespace cleanup
misc: remove AVR32 dependencies
virt: vbox: Add error mapping for VERR_INVALID_NAME and VERR_NO_MORE_FILES
soundwire: Fix a signedness bug
uio_hv_generic: fix new type mismatch warnings
uio_hv_generic: fix type mismatch warnings
auxdisplay: img-ascii-lcd: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
uio_hv_generic: add rescind support
uio_hv_generic: check that host supports monitor page
uio_hv_generic: create send and receive buffers
uio: document uio_hv_generic regions
doc: fix documentation about uio_hv_generic
vmbus: add monitor_id and subchannel_id to sysfs per channel
vmbus: fix ABI documentation
uio_hv_generic: use ISR callback method
...
Clean up drivers/Makefile by moving the pci/endpoint and pci/dwc entries
from drivers/Makefile into drivers/pci/Makefile.
Since we don't want to introduce any dependency between CONFIG_PCI and
CONFIG_PCI_ENDPOINT, we now always execute drivers/pci/Makefile.
Hence all Makefiles in drivers/pci/ were updated accordingly so no file is
compiled when CONFIG_PCI is not defined.
Also, we add a comment to reinforce that EPC and EPF libraries must be
initialized before their users. Hence built-in EPC drivers, such as
those of Designware, are linked after the endpoint core libraries.
Finally, we add another comment to explain why obj-y has been chosen
instead of obj-$(CONFIG_PCIE_DW) to parse the dwc/ sub-folder.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@free-electrons.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This adds the base SoundWire bus type, bus and driver registration.
along with changes to module device table for new SoundWire
device type.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-By: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SLIMbus (Serial Low Power Interchip Media Bus) is a specification
developed by MIPI (Mobile Industry Processor Interface) alliance.
SLIMbus is a 2-wire implementation, which is used to communicate with
peripheral components like audio-codec.
SLIMbus uses Time-Division-Multiplexing to accommodate multiple data
channels, and control channel. Control channel has messages to do
device-enumeration, messages to send/receive control-data to/from
SLIMbus devices, messages for port/channel management, and messages to
do bandwidth allocation.
The framework supports multiple instances of the bus (1 controller per
bus), and multiple slave devices per controller.
This patch adds support to basic silmbus core which includes support to
SLIMbus type, slimbus device registeration and some basic data structures.
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SIOX is a bus system invented at Eckelmann AG to control their building
management and refrigeration systems. Traditionally the bus was
implemented on custom microcontrollers, today Linux based machines are
in use, too.
The topology on a SIOX bus looks as follows:
,------->--DCLK-->---------------+----------------------.
^ v v
,--------. ,----------------------. ,------
| | | ,--------------. | |
| |--->--DOUT-->---|->-|shift register|->-|--->---|
| | | `--------------' | |
| master | | device | | device
| | | ,--------------. | |
| |---<--DIN---<---|-<-|shift register|-<-|---<---|
| | | `--------------' | |
`--------' `----------------------' `------
v ^ ^
`----------DLD-------------------+----------------------'
There are two control lines (DCLK and DLD) driven from the bus master to
all devices in parallel and two daisy chained data lines, one for input
and one for output. DCLK is the clock to shift both chains by a single
bit. On an edge of DLD the devices latch both their input and output
shift registers.
This patch adds a framework for this bus type.
Acked-by: Gavin Schenk <g.schenk@eckelmann.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the visorbus driver out of staging (drivers/staging/unisys/visorbus)
and to drivers/visorbus. Modify the configuration and makefiles so they
now reference the new location. The s-Par header file visorbus.h that is
referenced by all s-Par drivers, is being moved into include/linux.
Signed-off-by: David Kershner <david.kershner@unisys.com>
Reviewed-by: Tim Sell <timothy.sell@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY drivers can use ULPI interfaces when CONFIG_USB (which is host side
support) is not enabled, so also build drivers/usb/ when CONFIG_USB_SUPPORT
is enabled so that drivers/usb/common/ is built.
ERROR: "ulpi_unregister_driver" [drivers/phy/ti/phy-tusb1210.ko] undefined!
ERROR: "__ulpi_register_driver" [drivers/phy/ti/phy-tusb1210.ko] undefined!
ERROR: "ulpi_read" [drivers/phy/ti/phy-tusb1210.ko] undefined!
ERROR: "ulpi_write" [drivers/phy/ti/phy-tusb1210.ko] undefined!
ERROR: "ulpi_unregister_driver" [drivers/phy/qualcomm/phy-qcom-usb-hs.ko] undefined!
ERROR: "__ulpi_register_driver" [drivers/phy/qualcomm/phy-qcom-usb-hs.ko] undefined!
ERROR: "ulpi_write" [drivers/phy/qualcomm/phy-qcom-usb-hs.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* pm-cpufreq-sched:
cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq
* pm-opp:
PM / OPP: Add dev_pm_opp_{un}register_get_pstate_helper()
PM / OPP: Support updating performance state of device's power domain
PM / OPP: add missing of_node_put() for of_get_cpu_node()
PM / OPP: Rename dev_pm_opp_register_put_opp_helper()
PM / OPP: Add missing of_node_put(np)
PM / OPP: Move error message to debug level
PM / OPP: Use snprintf() to avoid kasprintf() and kfree()
PM / OPP: Move the OPP directory out of power/
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drivers/base/power/ directory is special and contains code related
to power management core like system suspend/resume, hibernation, etc.
It was fine to keep the OPP code inside it when we had just one file for
it, but it is growing now and already has a directory for itself.
Lets move it directly under drivers/ directory, just like cpufreq and
cpuidle.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lguest seems to be rather unused these days. It has seen only patches
ensuring it still builds the last two years and its official state is
"Odd Fixes".
Remove it in order to be able to clean up the paravirt code.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: boris.ostrovsky@oracle.com
Cc: lguest@lists.ozlabs.org
Cc: rusty@rustcorp.com.au
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20170816173157.8633-3-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a new minimalistic subsystem that handles multiplexer controllers.
When multiplexers are used in various places in the kernel, and the
same multiplexer controller can be used for several independent things,
there should be one place to implement support for said multiplexer
controller.
A single multiplexer controller can also be used to control several
parallel multiplexers, that are in turn used by different subsystems
in the kernel, leading to a need to coordinate multiplexer accesses.
The multiplexer subsystem handles this coordination.
Thanks go out to Lars-Peter Clausen, Jonathan Cameron, Rob Herring,
Wolfram Sang, Paul Gortmaker, Dan Carpenter, Colin Ian King, Greg
Kroah-Hartman and last but certainly not least to Philipp Zabel for
helpful comments, reviews, patches and general encouragement!
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This branch introduces a generic TEE framework in the kernel, to handle
trusted environemtns (security coprocessor or software implementations
such as OP-TEE/TrustZone). I'm sending it separately from the other
arm-soc driver changes to give it a little more visibility, once
the subsystem is merged, we will likely keep this in the arm₋soc
drivers branch or have the maintainers submit pull requests directly,
depending on the patch volume.
I have reviewed earlier versions in the past, and have reviewed
the latest version in person during Linaro Connect BUD17.
Here is my overall assessment of the subsystem:
* There is clearly demand for this, both for the generic
infrastructure and the specific OP-TEE implementation.
* The code has gone through a large number of reviews,
and the review comments have all been addressed, but
the reviews were not coming up with serious issues any more
and nobody volunteered to vouch for the quality.
* The user space ioctl interface is sufficient to work with the
OP-TEE driver, and it should in principle work with other
TEE implementations that follow the GlobalPlatform[1] standards,
but it might need to be extended in minor ways depending on
specific requirements of future TEE implementations
* The main downside of the API to me is how the user space
is tied to the TEE implementation in hardware or firmware,
but uses a generic way to communicate with it. This seems
to be an inherent problem with what it is trying to do,
and I could not come up with any better solution than what
is implemented here.
For a detailed history of the patch series, see
https://lkml.org/lkml/2017/3/10/1277
Conflicts: needs a fixup after the drm tree was merged, see
https://patchwork.kernel.org/patch/9691679/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VzpB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-tee' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull TEE driver infrastructure and OP-TEE drivers from Arnd Bergmann:
"This introduces a generic TEE framework in the kernel, to handle
trusted environemtns (security coprocessor or software implementations
such as OP-TEE/TrustZone). I'm sending it separately from the other
arm-soc driver changes to give it a little more visibility, once the
subsystem is merged, we will likely keep this in the arm₋soc drivers
branch or have the maintainers submit pull requests directly,
depending on the patch volume.
I have reviewed earlier versions in the past, and have reviewed the
latest version in person during Linaro Connect BUD17.
Here is my overall assessment of the subsystem:
- There is clearly demand for this, both for the generic
infrastructure and the specific OP-TEE implementation.
- The code has gone through a large number of reviews, and the review
comments have all been addressed, but the reviews were not coming
up with serious issues any more and nobody volunteered to vouch for
the quality.
- The user space ioctl interface is sufficient to work with the
OP-TEE driver, and it should in principle work with other TEE
implementations that follow the GlobalPlatform[1] standards, but it
might need to be extended in minor ways depending on specific
requirements of future TEE implementations
- The main downside of the API to me is how the user space is tied to
the TEE implementation in hardware or firmware, but uses a generic
way to communicate with it. This seems to be an inherent problem
with what it is trying to do, and I could not come up with any
better solution than what is implemented here.
For a detailed history of the patch series, see
https://lkml.org/lkml/2017/3/10/1277"
* tag 'armsoc-tee' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dt: hikey: Add optee node
Documentation: tee subsystem and op-tee driver
tee: add OP-TEE driver
tee: generic TEE subsystem
dt/bindings: add bindings for optee
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=eE4D
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add framework for supporting PCIe devices in Endpoint mode (Kishon
Vijay Abraham I)
- use non-postable PCI config space mappings when possible (Lorenzo
Pieralisi)
- clean up and unify mmap of PCI BARs (David Woodhouse)
- export and unify Function Level Reset support (Christoph Hellwig)
- avoid FLR for Intel 82579 NICs (Sasha Neftin)
- add pci_request_irq() and pci_free_irq() helpers (Christoph Hellwig)
- short-circuit config access failures for disconnected devices (Keith
Busch)
- remove D3 sleep delay when possible (Adrian Hunter)
- freeze PME scan before suspending devices (Lukas Wunner)
- stop disabling MSI/MSI-X in pci_device_shutdown() (Prarit Bhargava)
- disable boot interrupt quirk for ASUS M2N-LR (Stefan Assmann)
- add arch-specific alignment control to improve device passthrough by
avoiding multiple BARs in a page (Yongji Xie)
- add sysfs sriov_drivers_autoprobe to control VF driver binding
(Bodong Wang)
- allow slots below PCI-to-PCIe "reverse bridges" (Bjorn Helgaas)
- fix crashes when unbinding host controllers that don't support
removal (Brian Norris)
- add driver for MicroSemi Switchtec management interface (Logan
Gunthorpe)
- add driver for Faraday Technology FTPCI100 host bridge (Linus
Walleij)
- add i.MX7D support (Andrey Smirnov)
- use generic MSI support for Aardvark (Thomas Petazzoni)
- make Rockchip driver modular (Brian Norris)
- advertise 128-byte Read Completion Boundary support for Rockchip
(Shawn Lin)
- advertise PCI_EXP_LNKSTA_SLC for Rockchip root port (Shawn Lin)
- convert atomic_t to refcount_t in HV driver (Elena Reshetova)
- add CPU IRQ affinity in HV driver (K. Y. Srinivasan)
- fix PCI bus removal in HV driver (Long Li)
- add support for ThunderX2 DMA alias topology (Jayachandran C)
- add ThunderX pass2.x 2nd node MCFG quirk (Tomasz Nowicki)
- add ITE 8893 bridge DMA alias quirk (Jarod Wilson)
- restrict Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
(Manish Jaggi)
* tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (146 commits)
PCI: Don't allow unbinding host controllers that aren't prepared
ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
MAINTAINERS: Add PCI Endpoint maintainer
Documentation: PCI: Add userguide for PCI endpoint test function
tools: PCI: Add sample test script to invoke pcitest
tools: PCI: Add a userspace tool to test PCI endpoint
Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
misc: Add host side PCI driver for PCI test function device
PCI: Add device IDs for DRA74x and DRA72x
dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
PCI: dwc: dra7xx: Workaround for errata id i870
dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
PCI: dwc: dra7xx: Add EP mode support
PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
dt-bindings: PCI: Add DT bindings for PCI designware EP mode
PCI: dwc: designware: Add EP mode support
Documentation: PCI: Add binding documentation for pci-test endpoint function
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: imx6: Fix spelling mistake: "contol" -> "control"
...
* Region media error reporting: A libnvdimm region device is the parent
to one or more namespaces. To date, media errors have been reported via
the "badblocks" attribute attached to pmem block devices for namespaces
in "raw" or "memory" mode. Given that namespaces can be in "device-dax"
or "btt-sector" mode this new interface reports media errors
generically, i.e. independent of namespace modes or state. This
subsequently allows userspace tooling to craft "ACPI 6.1 Section
9.20.7.6 Function Index 4 - Clear Uncorrectable Error" requests and
submit them via the ioctl path for NVDIMM root bus devices.
* Introduce 'struct dax_device' and 'struct dax_operations': Prompted by
a request from Linus and feedback from Christoph this allows for dax
capable drivers to publish their own custom dax operations. This fixes
the broken assumption that all dax operations are related to a
persistent memory device, and makes it easier for other architectures
and platforms to add customized persistent memory support.
* 'libnvdimm' core updates: A new "deep_flush" sysfs attribute is
available for storage appliance applications to manually trigger memory
controllers to drain write-pending buffers that would otherwise be
flushed automatically by the platform ADR (asynchronous-DRAM-refresh)
mechanism at a power loss event. Support for "locked" DIMMs is included
to prevent namespaces from surfacing when the namespace label data area
is locked. Finally, fixes for various reported deadlocks and crashes,
also tagged for -stable.
* ACPI / nfit driver updates: General updates of the nfit driver to add
DSM command overrides, ACPI 6.1 health state flags support, DSM payload
debug available by default, and various fixes.
Acknowledgements that came after the branch was pushed:
commmit 565851c972 "device-dax: fix sysfs attribute deadlock"
Tested-by: Yi Zhang <yizhan@redhat.com>
commit 23f4984483 "libnvdimm: rework region badblocks clearing"
Tested-by: Toshi Kani <toshi.kani@hpe.com>
-----BEGIN PGP SIGNATURE-----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=Ox0s
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"The bulk of this has been in multiple -next releases. There were a few
late breaking fixes and small features that got added in the last
couple days, but the whole set has received a build success
notification from the kbuild robot.
Change summary:
- Region media error reporting: A libnvdimm region device is the
parent to one or more namespaces. To date, media errors have been
reported via the "badblocks" attribute attached to pmem block
devices for namespaces in "raw" or "memory" mode. Given that
namespaces can be in "device-dax" or "btt-sector" mode this new
interface reports media errors generically, i.e. independent of
namespace modes or state.
This subsequently allows userspace tooling to craft "ACPI 6.1
Section 9.20.7.6 Function Index 4 - Clear Uncorrectable Error"
requests and submit them via the ioctl path for NVDIMM root bus
devices.
- Introduce 'struct dax_device' and 'struct dax_operations': Prompted
by a request from Linus and feedback from Christoph this allows for
dax capable drivers to publish their own custom dax operations.
This fixes the broken assumption that all dax operations are
related to a persistent memory device, and makes it easier for
other architectures and platforms to add customized persistent
memory support.
- 'libnvdimm' core updates: A new "deep_flush" sysfs attribute is
available for storage appliance applications to manually trigger
memory controllers to drain write-pending buffers that would
otherwise be flushed automatically by the platform ADR
(asynchronous-DRAM-refresh) mechanism at a power loss event.
Support for "locked" DIMMs is included to prevent namespaces from
surfacing when the namespace label data area is locked. Finally,
fixes for various reported deadlocks and crashes, also tagged for
-stable.
- ACPI / nfit driver updates: General updates of the nfit driver to
add DSM command overrides, ACPI 6.1 health state flags support, DSM
payload debug available by default, and various fixes.
Acknowledgements that came after the branch was pushed:
- commmit 565851c972 "device-dax: fix sysfs attribute deadlock":
Tested-by: Yi Zhang <yizhan@redhat.com>
- commit 23f4984483 "libnvdimm: rework region badblocks clearing"
Tested-by: Toshi Kani <toshi.kani@hpe.com>"
* tag 'libnvdimm-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (52 commits)
libnvdimm, pfn: fix 'npfns' vs section alignment
libnvdimm: handle locked label storage areas
libnvdimm: convert NDD_ flags to use bitops, introduce NDD_LOCKED
brd: fix uninitialized use of brd->dax_dev
block, dax: use correct format string in bdev_dax_supported
device-dax: fix sysfs attribute deadlock
libnvdimm: restore "libnvdimm: band aid btt vs clear poison locking"
libnvdimm: fix nvdimm_bus_lock() vs device_lock() ordering
libnvdimm: rework region badblocks clearing
acpi, nfit: kill ACPI_NFIT_DEBUG
libnvdimm: fix clear length of nvdimm_forget_poison()
libnvdimm, pmem: fix a NULL pointer BUG in nd_pmem_notify
libnvdimm, region: sysfs trigger for nvdimm_flush()
libnvdimm: fix phys_addr for nvdimm_clear_poison
x86, dax, pmem: remove indirection around memcpy_from_pmem()
block: remove block_device_operations ->direct_access()
block, dax: convert bdev_dax_supported() to dax_direct_access()
filesystem-dax: convert to dax_direct_access()
Revert "block: use DAX for partition table reads"
ext2, ext4, xfs: retrieve dax_device for iomap operations
...
DWC3 driver uses of_usb_get_phy_mode() which is
implemented in drivers/usb/phy/of.c and in bare minimal
configuration it might not be pulled in kernel binary.
In case of ARC or ARM this could be easily reproduced with
"allnodefconfig" +CONFIG_USB=m +CONFIG_USB_DWC3=m.
On building all ends-up with:
---------------------->8------------------
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Building modules, stage 2.
MODPOST 5 modules
ERROR: "of_usb_get_phy_mode" [drivers/usb/dwc3/dwc3.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
---------------------->8------------------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: linux-snps-arc@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want dax capable drivers to be able to publish a set of dax
operations [1]. However, we do not want to further abuse block_devices
to advertise these operations. Instead we will attach these operations
to a dax device and add a lookup mechanism to go from block device path
to a dax device. A dax capable driver like pmem or brd is responsible
for registering a dax device, alongside a block device, and then a dax
capable filesystem is responsible for retrieving the dax device by path
name if it wants to call dax_operations.
For now, we refactor the dax pseudo-fs to be a generic facility, rather
than an implementation detail, of the device-dax use case. Where a "dax
device" is just an inode + dax infrastructure, and "Device DAX" is a
mapping service layered on top of that base 'struct dax_device'.
"Filesystem DAX" is then a mapping service that layers a filesystem on
top of that same base device. Filesystem DAX is associated with a
block_device for now, but perhaps directly to a dax device in the
future, or for new pmem-only filesystems.
[1]: https://lkml.org/lkml/2017/1/19/880
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Introduce a new EP core layer in order to support endpoint functions in
linux kernel. This comprises the EPC library (Endpoint Controller Library)
and EPF library (Endpoint Function Library). EPC library implements
functions specific to an endpoint controller and EPF library implements
functions specific to an endpoint function.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Initial patch for generic TEE subsystem.
This subsystem provides:
* Registration/un-registration of TEE drivers.
* Shared memory between normal world and secure world.
* Ioctl interface for interaction with user space.
* Sysfs implementation_id of TEE driver
A TEE (Trusted Execution Environment) driver is a driver that interfaces
with a trusted OS running in some secure environment, for example,
TrustZone on ARM cpus, or a separate secure co-processor etc.
The TEE subsystem can serve a TEE driver for a Global Platform compliant
TEE, but it's not limited to only Global Platform TEEs.
This patch builds on other similar implementations trying to solve
the same problem:
* "optee_linuxdriver" by among others
Jean-michel DELORME<jean-michel.delorme@st.com> and
Emmanuel MICHEL <emmanuel.michel@st.com>
* "Generic TrustZone Driver" by Javier González <javier@javigon.com>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Tested-by: Jerome Forissier <jerome.forissier@linaro.org> (HiKey)
Tested-by: Volodymyr Babchuk <vlad.babchuk@gmail.com> (RCAR H3)
Tested-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4Owc
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add ASPM L1 substate support
- enable PCIe Extended Tags when supported
- configure PCIe MPS settings on iProc, Versatile, X-Gene, and Xilinx
- increase VPD access timeout
- add ACS quirks for Intel Union Point, Qualcomm QDF2400 and QDF2432
- use new pci_irq_alloc_vectors() in more drivers
- fix MSI affinity memory leak
- remove unused MSI interfaces and update documentation
- remove unused AER .link_reset() callback
- avoid pci_lock / p->pi_lock deadlock seen with perf
- serialize sysfs enable/disable num_vfs operations
- move DesignWare IP from drivers/pci/host/ to drivers/pci/dwc/ and
refactor so we can support both hosts and endpoints
- add DT ECAM-like support for HiSilicon Hip06/Hip07 controllers
- add Rockchip system power management support
- add Thunder-X cn81xx and cn83xx support
- add Exynos 5440 PCIe PHY support
* tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (93 commits)
PCI: dwc: Remove dependency of designware on CONFIG_PCI
PCI: dwc: Add CONFIG_PCIE_DW_HOST to enable PCI dwc host
PCI: dwc: Split pcie-designware.c into host and core files
PCI: dwc: designware: Fix style errors in pcie-designware.c
PCI: dwc: designware: Parse "num-lanes" property in dw_pcie_setup_rc()
PCI: dwc: all: Split struct pcie_port into host-only and core structures
PCI: dwc: designware: Get device pointer at the start of dw_pcie_host_init()
PCI: dwc: all: Rename cfg_read/cfg_write to read/write
PCI: dwc: all: Use platform_set_drvdata() to save private data
PCI: dwc: designware: Move register defines to designware header file
PCI: dwc: Use PTR_ERR_OR_ZERO to simplify code
PCI: dra7xx: Group PHY API invocations
PCI: dra7xx: Enable MSI and legacy interrupts simultaneously
PCI: dra7xx: Add support to force RC to work in GEN1 mode
PCI: dra7xx: Simplify probe code with devm_gpiod_get_optional()
PCI: Move DesignWare IP support to new drivers/pci/dwc/ directory
PCI: exynos: Support the PHY generic framework
Documentation: binding: Modify the exynos5440 PCIe binding
phy: phy-exynos-pcie: Add support for Exynos PCIe PHY
Documentation: samsung-phy: Add exynos-pcie-phy binding
...
CONFIG_PCI is used to enable host mode PCI. In preparation for adding
endpoint mode support to designware driver, remove the dependency of
designware on CONFIG_PCI and make only the host-specific part depend on
CONFIG_PCI.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This change adds the initial (empty) fsi bus definition, and introduces
drivers/fsi/.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Chris Bostic <cbostic@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to break the hard dependency between the PTP clock subsystem and
ethernet drivers capable of being clock providers, this patch provides
simple PTP stub functions to allow linkage of those drivers into the
kernel even when the PTP subsystem is configured out. Drivers must be
ready to accept NULL from ptp_clock_register() in that case.
And to make it possible for PTP to be configured out, the select statement
in those driver's Kconfig menu entries is converted to the new "imply"
statement. This way the PTP subsystem may have Kconfig dependencies of
its own, such as POSIX_TIMERS, without having to make those ethernet
drivers unavailable if POSIX timers are cconfigured out. And when support
for POSIX timers is selected again then the default config option for PTP
clock support will automatically be adjusted accordingly.
The pch_gbe driver is a bit special as it relies on extra code in
drivers/ptp/ptp_pch.c. Therefore we let the make process descend into
drivers/ptp/ even if PTP_1588_CLOCK is unselected.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-kbuild@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Michal Marek <mmarek@suse.com>
Link: http://lkml.kernel.org/r/1478841010-28605-4-git-send-email-nicolas.pitre@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I was on vacation during the merge window (a long vacation)
but this is a bug fix that should go in and a new driver that shouldn't
hurt anything.
This has been in linux-next for a month or so.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlgKVpoACgkQIXnXXONXERdGBACeONBS0wOf4Rv+bxSOdeJcTwLJ
rmoAoJ2R0BpWE1imvcC+AqXOoqg2c48k
=P4Dz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull IPMI updates from Corey Minyard:
"A small bug fix and a new driver for acting as an IPMI device.
I was on vacation during the merge window (a long vacation) but this
is a bug fix that should go in and a new driver that shouldn't hurt
anything.
This has been in linux-next for a month or so"
* tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: fix crash on reading version from proc after unregisted bmc
ipmi/bt-bmc: remove redundant return value check of platform_get_resource()
ipmi/bt-bmc: add a dependency on ARCH_ASPEED
ipmi: Fix ioremap error handling in bt-bmc
ipmi: add an Aspeed BT IPMI BMC driver
This patch adds a simple device driver to expose the iBT interface on
Aspeed SOCs (AST2400 and AST2500) as a character device. Such SOCs are
commonly used as BMCs (BaseBoard Management Controllers) and this
driver implements the BMC side of the BT interface.
The BT (Block Transfer) interface is used to perform in-band IPMI
communication between a host and its BMC. Entire messages are buffered
before sending a notification to the other end, host or BMC, that
there is data to be read. Usually, the host emits requests and the BMC
responses but the specification provides a mean for the BMC to send
SMS Attention (BMC-to-Host attention or System Management Software
attention) messages.
For this purpose, the driver introduces a specific ioctl on the
device: 'BT_BMC_IOCTL_SMS_ATN' that can be used by the system running
on the BMC to signal the host of such an event.
The device name defaults to '/dev/ipmi-bt-host'
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
[clg: - checkpatch fixes
- added a devicetree binding documentation
- replace 'bt_host' by 'bt_bmc' to reflect that the driver is
the BMC side of the IPMI BT interface
- renamed the device to 'ipmi-bt-host'
- introduced a temporary buffer to copy_{to,from}_user
- used platform_get_irq()
- moved the driver under drivers/char/ipmi/ but kept it as a misc
device
- changed the compatible cell to "aspeed,ast2400-bt-bmc"
]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[clg: - checkpatch --strict fixes
- removed the use of devm_iounmap, devm_kfree in cleanup paths
- introduced an atomic-t to limit opens to 1
- introduced a mutex to protect write/read operations]
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Several SoCs implement platform drivers for clocks rather than
CLK_OF_DECLARE(). Clocks should come earlier because they are
prerequisites for many of other drivers. It will help to mitigate
EPROBE_DEFER issues.
Also, drop the comment since it does not carry much value.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- New vsock device support in host and guest
- Platform IOMMU support in host and guest,
including compatibility quirks for legacy systems.
- Misc fixes and cleanups.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXofvbAAoJECgfDbjSjVRpUTIH/iEoK9h636tBayXy0PXkPby0
6fMaRFy6H1HgEttgDhJE8Pqg/ba3qaW9Em0fHyFq7Mp2waFHAZ8hAT8phC6TAK3c
CIBnfzyyuI8u3N9SnNOfelPVcwCBfuALuuTsXB/rwKbYQEVv+U5Rdt3Vyx9+lXkj
P005klz7PfqxFhQrrnj4Eh7VawtHwmMuLH8YoWpCZpM71dHPo6eL+3ftKwhH2boo
qK86uVprwba03Pewpm13vQnotemfVfUUkjXd4EJpG3dx7E0KZosuj0ZG9OV8mPGQ
Cl2gBdUhocdJgeUnAHmf6tumYi9KFlYfy6xLy44YMmN7FL3E9nQjaKZp25UKfiM=
=ztIm
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost updates from Michael Tsirkin:
- new vsock device support in host and guest
- platform IOMMU support in host and guest, including compatibility
quirks for legacy systems.
- misc fixes and cleanups.
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
VSOCK: Use kvfree()
vhost: split out vringh Kconfig
vhost: detect 32 bit integer wrap around
vhost: new device IOTLB API
vhost: drop vringh dependency
vhost: convert pre sorted vhost memory array to interval tree
vhost: introduce vhost memory accessors
VSOCK: Add Makefile and Kconfig
VSOCK: Introduce vhost_vsock.ko
VSOCK: Introduce virtio_transport.ko
VSOCK: Introduce virtio_vsock_common.ko
VSOCK: defer sock removal to transports
VSOCK: transport-specific vsock_transport functions
vhost: drop vringh dependency
vop: pull in vhost Kconfig
virtio: new feature to detect IOMMU device quirk
balloon: check the number of available pages in leak balloon
vhost: lockless enqueuing
vhost: simplify work flushing
* proper runtime pm support for omap-ssi and ssi-protocol
* misc. fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WPyp
-----END PGP SIGNATURE-----
Merge tag 'hsi-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi
Pull HSI updates from Sebastian Reichel:
- proper runtime pm support for omap-ssi and ssi-protocol
- misc fixes
* tag 'hsi-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi: (24 commits)
HSI: omap_ssi: drop pm_runtime_irq_safe
HSI: omap_ssi_port: use rpm autosuspend API
HSI: omap_ssi: call msg->complete() from process context
HSI: omap_ssi_port: ensure clocks are kept enabled during transfer
HSI: omap_ssi_port: replace pm_runtime_put_sync with non-sync variant
HSI: omap_ssi_port: avoid calling runtime_pm_*_sync inside spinlock
HSI: omap_ssi_port: avoid pm_runtime_get_sync in ssi_start_dma and ssi_start_pio
HSI: omap_ssi_port: switch to threaded pio irq
HSI: omap_ssi_core: remove pm_runtime_get_sync call from tasklet
HSI: omap_ssi_core: use pm_runtime_put instead of pm_runtime_put_sync
HSI: omap_ssi_port: prepare start_tx/stop_tx for blocking pm_runtime calls
HSI: core: switch port event notifier from atomic to blocking
HSI: omap_ssi_port: replace wkin_cken with atomic bitmap operations
HSI: omap_ssi: convert cawake irq handler to thread
HSI: ssi_protocol: fix ssip_xmit invocation
HSI: ssi_protocol: replace spin_lock with spin_lock_bh
HSI: ssi_protocol: avoid ssi_waketest call with held spinlock
HSI: omap_ssi: do not reset module
HSI: omap_ssi_port: remove useless newline
hsi: Only descend into hsi directory when CONFIG_HSI is set
...
- LED driver for TI LP3952 6-Channel Color LED
LED core improvements:
- Only descend into leds directory when CONFIG_NEW_LEDS is set
- Add no-op gpio_led_register_device when LED subsystem is disabled
- MAINTAINERS: Add file patterns for led device tree bindings
LED Trigger core improvements:
- return error if invalid trigger name is provided via sysfs
LED class drivers improvements
- is31fl32xx: define complete i2c_device_id table
- is31fl32xx: fix typo in id and match table names
- leds-gpio: Set of_node for created LED devices
- pca9532: Add device tree support
Conversion of IDE trigger to common disk trigger:
- leds: convert IDE trigger to common disk trigger
- leds: documentation: 'ide-disk' to 'disk-activity'
- unicore32: use the new LED disk activity trigger
- parisc: use the new LED disk activity trigger
- mips: use the new LED disk activity trigger
- arm: use the new LED disk activity trigger
- powerpc: use the new LED disk activity trigger
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=8lmX
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"New LED class driver:
- LED driver for TI LP3952 6-Channel Color LED
LED core improvements:
- Only descend into leds directory when CONFIG_NEW_LEDS is set
- Add no-op gpio_led_register_device when LED subsystem is disabled
- MAINTAINERS: Add file patterns for led device tree bindings
LED Trigger core improvements:
- return error if invalid trigger name is provided via sysfs
LED class drivers improvements
- is31fl32xx: define complete i2c_device_id table
- is31fl32xx: fix typo in id and match table names
- leds-gpio: Set of_node for created LED devices
- pca9532: Add device tree support
Conversion of IDE trigger to common disk trigger:
- leds: convert IDE trigger to common disk trigger
- leds: documentation: 'ide-disk' to 'disk-activity'
- unicore32: use the new LED disk activity trigger
- parisc: use the new LED disk activity trigger
- mips: use the new LED disk activity trigger
- arm: use the new LED disk activity trigger
- powerpc: use the new LED disk activity trigger"
* tag 'leds_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: is31fl32xx: define complete i2c_device_id table
leds: is31fl32xx: fix typo in id and match table names
leds: LED driver for TI LP3952 6-Channel Color LED
leds: leds-gpio: Set of_node for created LED devices
leds: triggers: return error if invalid trigger name is provided via sysfs
leds: Only descend into leds directory when CONFIG_NEW_LEDS is set
leds: Add no-op gpio_led_register_device when LED subsystem is disabled
unicore32: use the new LED disk activity trigger
parisc: use the new LED disk activity trigger
mips: use the new LED disk activity trigger
arm: use the new LED disk activity trigger
powerpc: use the new LED disk activity trigger
leds: documentation: 'ide-disk' to 'disk-activity'
leds: convert IDE trigger to common disk trigger
leds: pca9532: Add device tree support
MAINTAINERS: Add file patterns for led device tree bindings
Core changes:
- The big item is of course the completion of the character
device ABI. It has now replaced and surpassed the former
unmaintainable sysfs ABI: we can now hammer (bitbang)
individual lines or sets of lines and read individual lines
or sets of lines from userspace, and we can also register
to listen to GPIO events from userspace. As a tie-in we
have two new tools in tools/gpio: gpio-hammer and
gpio-event-mon that illustrate the proper use of the new
ABI. As someone said: the wild west days of GPIO are now
over.
- Continued to remove the pointless
ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB Kconfig symbols.
I'm patching hexagon, openrisc, powerpc, sh, unicore,
ia64 and microblaze. These are either ACKed by their
maintainers or patched anyways after a grace period and
no response from maintainers. Some archs (ARM) come in from
their trees, and others (x86) are still not fixed, so I
might send a second pull request to root it out later in
this merge window, or just defer to v4.9.
- The GPIO tools are moved to the tools build system.
New drivers:
- New driver for the MAX77620/MAX20024.
- New driver for the Intel Merrifield.
- Enabled PCA953x for the TI PCA9536.
- Enabled PCA953x for the Intel Edison.
- Enabled R8A7792 in the RCAR driver.
Driver improvements:
- The STMPE and F7188x now supports the .get_direction()
callback.
- The Xilinx driver supports setting multiple lines at
once.
- ACPI support for the Vulcan GPIO controller.
- The MMIO GPIO driver supports device tree probing.
- The Acer One 10 is supported through the _DEP ACPI
attribute.
Cleanups:
- A major cleanup of the OF/DT support code. It is way
easier to read and understand now, probably this improves
performance too.
- Drop a few redundant .owner assignments.
- Remove CLPS711x boardfile support: we are 100% DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXlcT4AAoJEEEQszewGV1zACwQAK5SZr0F5c3QvYbJSiJBCGA7
MZKUYHnYoBpZaPKcFKoOXEM1WOvlABlh9U0y0xkL8gQ6giyKup1wYJJCuYgW29gL
ny4r7Z8rs2Wm1ujL+FLAwuxIwCY3BnhUucp8YiSaHPBuKRfsHorFPvXiAgLZjNYC
Qk3Q48xYW4inw9sy2BbMfsU3CZnkvgy5euooyy1ezwachRhuHdBy/MVCG012PC4s
0d6LGdByEx1uK4NeV7ssPys444M8unep2EWgy6Rvc1U+FmGA487EvL+X8nxTQTj3
uTMxA8nddmZTEeEIqhpRw/dPiFlWxPFwfWmNEre05gKLb/LUK2tgsUOnmIFgVUw/
t41IzdQNLQQZxmiXplZn6s5mAr2VNuTxkRq1CIl4SwQW+Uy4TU3q8aDPkKzsyhiR
yw6o6ul0pQs8UZEggnht8ie6JiSnJ55ehI/nlRxpK/797Ff6Yp4FARs3ZtFnQDDu
SWewnbRatZQ89lvy4BA7QCWeV4Scjk4k/e2HjUAFnkfMDaYqpi4vTdzwnWdVjd+F
hMgu6VnkN3oSE7ZMrKJMh7b7h1uMnIwKBFWbkrlOEuhT1X0ZDsEOBv5juSBPYomN
EOIJUyWqxn0ZfxeONbdbCPteYlfJF+TW/rE9LQMxS1nNwsqw2IQW6NCmrM9Nx6Fv
FP++26nYMTSh82gwOYw3
=NwcK
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.8 kernel cycle. The big
news is the completion of the chardev ABI which I'm very happy about
and apart from that it's an ordinary, quite busy cycle. The details
are below.
The patches are tested in linux-next for some time, patches to other
subsystem mostly have ACKs.
I got overly ambitious with configureing lines as input for IRQ lines
but it turns out that some controllers have their interrupt-enable and
input-enabling in orthogonal settings so the assumption that all IRQ
lines are input lines does not hold. Oh well, revert and back to the
drawing board with that.
Core changes:
- The big item is of course the completion of the character device
ABI. It has now replaced and surpassed the former unmaintainable
sysfs ABI: we can now hammer (bitbang) individual lines or sets of
lines and read individual lines or sets of lines from userspace,
and we can also register to listen to GPIO events from userspace.
As a tie-in we have two new tools in tools/gpio: gpio-hammer and
gpio-event-mon that illustrate the proper use of the new ABI. As
someone said: the wild west days of GPIO are now over.
- Continued to remove the pointless ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
Kconfig symbols. I'm patching hexagon, openrisc, powerpc, sh,
unicore, ia64 and microblaze. These are either ACKed by their
maintainers or patched anyways after a grace period and no response
from maintainers.
Some archs (ARM) come in from their trees, and others (x86) are
still not fixed, so I might send a second pull request to root it
out later in this merge window, or just defer to v4.9.
- The GPIO tools are moved to the tools build system.
New drivers:
- New driver for the MAX77620/MAX20024.
- New driver for the Intel Merrifield.
- Enabled PCA953x for the TI PCA9536.
- Enabled PCA953x for the Intel Edison.
- Enabled R8A7792 in the RCAR driver.
Driver improvements:
- The STMPE and F7188x now supports the .get_direction() callback.
- The Xilinx driver supports setting multiple lines at once.
- ACPI support for the Vulcan GPIO controller.
- The MMIO GPIO driver supports device tree probing.
- The Acer One 10 is supported through the _DEP ACPI attribute.
Cleanups:
- A major cleanup of the OF/DT support code. It is way easier to
read and understand now, probably this improves performance too.
- Drop a few redundant .owner assignments.
- Remove CLPS711x boardfile support: we are 100% DT"
* tag 'gpio-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (67 commits)
MAINTAINERS: Add INTEL MERRIFIELD GPIO entry
gpio: dwapb: add missing fwnode_handle_put() in dwapb_gpio_get_pdata()
gpio: merrifield: Protect irq_ack() and gpio_set() by lock
gpio: merrifield: Introduce GPIO driver to support Merrifield
gpio: intel-mid: Make it depend to X86_INTEL_MID
gpio: intel-mid: Sort header block alphabetically
gpio: intel-mid: Remove potentially harmful code
gpio: rcar: add R8A7792 support
gpiolib: remove duplicated include from gpiolib.c
Revert "gpio: convince line to become input in irq helper"
gpiolib: of_find_gpio(): Don't discard errors
gpio: of: Allow overriding the device node
gpio: free handles in fringe cases
gpio: tps65218: Add platform_device_id table
gpio: max77620: get gpio value based on direction
gpio: lynxpoint: avoid potential warning on error path
tools/gpio: add install section
tools/gpio: move to tools buildsystem
gpio: intel-mid: switch to devm_gpiochip_add_data()
gpio: 74x164: Use spi_write() helper instead of open coding
...
When CONFIG_NEW_LEDS is not set make will still descend into the leds
directory but nothing will be built. This produces unneeded build
artifacts and messages in addition to slowing the build. Fix this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
When CONFIG_HSI is not set make will still descend into the hsi
directory but nothing will be built. This produces unneeded build
artifacts and messages in addition to slowing the build. Fix this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
When CONFIG_GPIOLIB is not set make will still descend into the gpio
directory but nothing will be built. This produces unneeded build
artifacts and messages in addition to slowing the build. Fix this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commits 71d076ceb2 ("ARM: shmobile: Enable PM and
PM_GENERIC_DOMAINS for SoCs with PM Domains") and 2ee98234b8
("arm64: renesas: Enable PM and PM_GENERIC_DOMAINS for SoCs with PM
Domains"), CONFIG_PM and CONFIG_PM_GENERIC_DOMAINS are enabled
unconditionally for Renesas ARM-based SoCs. Hence the legacy clock
domain is no longer used on these SoCs.
Remove the related support code, and stop entering drivers/sh/ on ARM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Device DAX is the device-centric analogue of Filesystem DAX
(CONFIG_FS_DAX). It allows memory ranges to be allocated and mapped
without need of an intervening file system. Device DAX is strict,
precise and predictable. Specifically this interface:
1/ Guarantees fault granularity with respect to a given page size (pte,
pmd, or pud) set at configuration time.
2/ Enforces deterministic behavior by being strict about what fault
scenarios are supported.
For example, by forcing MADV_DONTFORK semantics and omitting MAP_PRIVATE
support device-dax guarantees that a mapping always behaves/performs the
same once established. It is the "what you see is what you get" access
mechanism to differentiated memory vs filesystem DAX which has
filesystem specific implementation semantics.
Persistent memory is the first target, but the mechanism is also
targeted for exclusive allocations of performance differentiated memory
ranges.
This commit is limited to the base device driver infrastructure to
associate a dax device with pmem range.
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently the reset/power off handlers (POWER_RESET) and Adaptive Voltage
Scaling class (POWER_AVS) are not built when POWER_SUPPLY is disabled.
The POWER_RESET is also not visible in drivers main section of config.
However they do not really depend on power supply so they can be built
always. The objects for power supply drivers already depend on
particular Kconfig symbols so there is no need for any changes in
drivers/power/Makefile.
This allows selecting POWER_RESET from main drivers config section and
fixes following build warning (encountered on ARM exynos defconfig when
POWER_SUPPLY is disabled manually):
warning: (ARCH_HISI && ARCH_INTEGRATOR && ARCH_EXYNOS && ARCH_VEXPRESS && REALVIEW_DT) selects POWER_RESET which has unmet direct dependencies (POWER_SUPPLY)
warning: (ARCH_EXYNOS) selects POWER_RESET_SYSCON which has unmet direct dependencies (POWER_SUPPLY && POWER_RESET && OF)
warning: (ARCH_EXYNOS) selects POWER_RESET_SYSCON_POWEROFF which has unmet direct dependencies (POWER_SUPPLY && POWER_RESET && OF)
Reported-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add support for registering as a LightNVM device. This allows us to
evaluate the performance of the LightNVM subsystem.
In /drivers/Makefile, LightNVM is moved above block device drivers
to make sure that the LightNVM media managers have been initialized
before drivers under /drivers/block are initialized.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Fix by Jens Axboe to remove unneeded slab cache and the following
memory leak.
Signed-off-by: Jens Axboe <axboe@fb.com>
Here is the big char/misc driver update for 4.4-rc1. Lots of different
driver and subsystem updates, hwtracing being the largest with the
addition of some new platforms that are now supported. Full details in
the shortlog.
All of these have been in linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6d/oACgkQMUfUDdst+yl93ACcCf91y+ufwU3cmcnq5LpwHPfx
VbkAn08Cn6Wu6IcihoEpR4hqGgIOtjqW
=1a3d
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver update for 4.4-rc1. Lots of
different driver and subsystem updates, hwtracing being the largest
with the addition of some new platforms that are now supported. Full
details in the shortlog.
All of these have been in linux-next for a long time with no reported
issues"
* tag 'char-misc-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (181 commits)
fpga: socfpga: Fix check of return value of devm_request_irq
lkdtm: fix ACCESS_USERSPACE test
mcb: Destroy IDA on module unload
mcb: Do not return zero on error path in mcb_pci_probe()
mei: bus: set the device name before running fixup
mei: bus: use correct lock ordering
mei: Fix debugfs filename in error output
char: ipmi: ipmi_ssif: Replace timeval with timespec64
fpga: zynq-fpga: Fix issue with drvdata being overwritten.
fpga manager: remove unnecessary null pointer checks
fpga manager: ensure lifetime with of_fpga_mgr_get
fpga: zynq-fpga: Change fw format to handle bin instead of bit.
fpga: zynq-fpga: Fix unbalanced clock handling
misc: sram: partition base address belongs to __iomem space
coresight: etm3x: adding documentation for sysFS's cpu interface
vme: 8-bit status/id takes 256 values, not 255
fpga manager: Adding FPGA Manager support for Xilinx Zynq 7000
ARM: zynq: dt: Updated devicetree for Zynq 7000 platform.
ARM: dt: fpga: Added binding docs for Xilinx Zynq FPGA manager.
ver_linux: proc/modules, limit text processing to 'sed'
...
Open-channel SSDs are devices that share responsibilities with the host
in order to implement and maintain features that typical SSDs keep
strictly in firmware. These include (i) the Flash Translation Layer
(FTL), (ii) bad block management, and (iii) hardware units such as the
flash controller, the interface controller, and large amounts of flash
chips. In this way, Open-channels SSDs exposes direct access to their
physical flash storage, while keeping a subset of the internal features
of SSDs.
LightNVM is a specification that gives support to Open-channel SSDs
LightNVM allows the host to manage data placement, garbage collection,
and parallelism. Device specific responsibilities such as bad block
management, FTL extensions to support atomic IOs, or metadata
persistence are still handled by the device.
The implementation of LightNVM consists of two parts: core and
(multiple) targets. The core implements functionality shared across
targets. This is initialization, teardown and statistics. The targets
implement the interface that exposes physical flash to user-space
applications. Examples of such targets include key-value store,
object-store, as well as traditional block devices, which can be
application-specific.
Contributions in this patch from:
Javier Gonzalez <jg@lightnvm.io>
Dongsheng Yang <yangds.fnst@cn.fujitsu.com>
Jesper Madsen <jmad@itu.dk>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch moves the NVMe driver from drivers/block/ to its own new
drivers/nvme/host/ directory. This is in preparation of splitting the
current monolithic driver up and add support for the upcoming NVMe
over Fabrics standard. The drivers/nvme/host/ is chose to leave space
for a NVMe target implementation in addition to this host side driver.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
[hch: rebased, renamed core.c to pci.c, slight tweaks]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
API to support programming FPGA's.
The following functions are exported as GPL:
* fpga_mgr_buf_load
Load fpga from image in buffer
* fpga_mgr_firmware_load
Request firmware and load it to the FPGA.
* fpga_mgr_register
* fpga_mgr_unregister
FPGA device drivers can be added by calling
fpga_mgr_register() to register a set of
fpga_manager_ops to do device specific stuff.
* of_fpga_mgr_get
* fpga_mgr_put
Get/put a reference to a fpga manager.
The following sysfs files are created:
* /sys/class/fpga_manager/<fpga>/name
Name of low level driver.
* /sys/class/fpga_manager/<fpga>/state
State of fpga manager
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel(R) Trace Hub (TH) is a set of hardware blocks (subdevices) that
produce, switch and output trace data from multiple hardware and
software sources over several types of trace output ports encoded
in System Trace Protocol (MIPI STPv2) and is intended to perform
full system debugging.
For these subdevices, we create a bus, where they can be discovered
and configured by userspace software.
This patch creates this bus infrastructure, three types of devices
(source, output, switch), resource allocation, some callback mechanisms
to facilitate communication between the subdevices' drivers and some
common sysfs attributes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A System Trace Module (STM) is a device exporting data in System Trace
Protocol (STP) format as defined by MIPI STP standards. Examples of such
devices are Intel(R) Trace Hub and Coresight STM.
This abstraction provides a unified interface for software trace sources
to send their data over an STM device to a debug host. In order to do
that, such a trace source needs to be assigned a pair of master/channel
identifiers that all the data from this source will be tagged with. The
STP decoder on the debug host side will use these master/channel tags to
distinguish different trace streams from one another inside one STP
stream.
This abstraction provides a configfs-based policy management mechanism
for dynamic allocation of these master/channel pairs based on trace
source-supplied string identifier. It has the flexibility of being
defined at runtime and at the same time (provided that the policy
definition is aligned with the decoding end) consistency.
For userspace trace sources, this abstraction provides write()-based and
mmap()-based (if the underlying stm device allows this) output mechanism.
For kernel-side trace sources, we provide "stm_source" device class that
can be connected to an stm device at run time.
Cc: linux-api@vger.kernel.org
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cycle
Core changes:
- It is possible configure groups in debugfs.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx also wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
Driver feature enhancements:
- Power management support for the SiRF SoC Atlas 7.
- Power down support for the Qualcomm driver.
- Intel Cherryview and Baytrail: switch drivers to use raw
spinlocks in IRQ handlers to play nice with the realtime
patch set.
- Rework and new modes handling for Qualcomm SPMI-MPP.
- Pinconf power source config for SH PFC.
New drivers and subdrivers:
- A new driver for Conexant Digicolor CX92755.
- A new driver for UniPhier PH1-LD4, PH1-Pro4, PH1-sLD8,
PH1-Pro5, ProXtream2 and PH1-LD6b SoC pin control support.
- Reverse-egineered the S/PDIF settings for the Allwinner
sun4i driver.
- Support for Qualcomm Technologies QDF2xxx ARM64 SoCs
- A new Freescale i.mx6ul subdriver.
Cleanup:
- Remove platform data support in a number of SH PFC
subdrivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4QFX
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.3 development
cycle.
Like with GPIO it's a lot of stuff. If my subsystems are any sign of
the overall tempo of the kernel v4.3 will be a gigantic diff.
[ It looks like 4.3 is calmer than 4.2 in most other subsystems, but
we'll see - Linus ]
Core changes:
- It is possible configure groups in debugfs.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data(). This series was
created by Thomas Gleixner after the problem was observed by
Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx also wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
Driver feature enhancements:
- Power management support for the SiRF SoC Atlas 7.
- Power down support for the Qualcomm driver.
- Intel Cherryview and Baytrail: switch drivers to use raw spinlocks
in IRQ handlers to play nice with the realtime patch set.
- Rework and new modes handling for Qualcomm SPMI-MPP.
- Pinconf power source config for SH PFC.
New drivers and subdrivers:
- A new driver for Conexant Digicolor CX92755.
- A new driver for UniPhier PH1-LD4, PH1-Pro4, PH1-sLD8, PH1-Pro5,
ProXtream2 and PH1-LD6b SoC pin control support.
- Reverse-egineered the S/PDIF settings for the Allwinner sun4i
driver.
- Support for Qualcomm Technologies QDF2xxx ARM64 SoCs
- A new Freescale i.mx6ul subdriver.
Cleanup:
- Remove platform data support in a number of SH PFC subdrivers"
* tag 'pinctrl-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (95 commits)
pinctrl: at91: fix null pointer dereference
pinctrl: mediatek: Implement wake handler and suspend resume
pinctrl: mediatek: Fix multiple registration issue.
pinctrl: sh-pfc: r8a7794: add USB pin groups
pinctrl: at91: Use generic irq_{request,release}_resources()
pinctrl: cherryview: Use raw_spinlock for locking
pinctrl: baytrail: Use raw_spinlock for locking
pinctrl: imx6ul: Remove .owner field
pinctrl: zynq: Fix typos in smc0_nand_grp and smc0_nor_grp
pinctrl: sh-pfc: Implement pinconf power-source param for voltage switching
clk: rockchip: add pclk_pd_pmu to the list of rk3288 critical clocks
pinctrl: sun4i: add spdif to pin description.
pinctrl: atlas7: clear ugly branch statements for pull and drivestrength
pinctrl: baytrail: Serialize all register access
pinctrl: baytrail: Drop FSF mailing address
pinctrl: rockchip: only enable gpio clock when it setting
pinctrl/mediatek: fix spelling mistake in dev_err error message
pinctrl: cherryview: Serialize all register access
pinctrl: UniPhier: PH1-Pro5: add I2C ch6 pin-mux setting
pinctrl: nomadik: reflect current input value
...
Boris Brezillon