o NPAR configuration which is programmed in fw, need to
restore after fw recovery.
o Update version to 5.0.7
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following changes are made:
1.Obtain capabilities of Nic partition.
2.Configure tx bandwidth of particular Nic partition.
3.Configure the eswitch for setting port mirroring, enable mac
learning, promiscous mode.
Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver uses FW API version 2 and thus code corresponding to FW API
version 1 has become obsolete. Clean up this from the driver.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After destroying recv ctx, context state remain same.
Fix it by marking as FREED.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we were allocating device resources during probe and
release them during remove.
Now alloc during interface up and release in interface down.
This helps in device performance, as it doesn't need to keep
track of inactive resources.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier all poll routine can process rx and tx, But now
one poll routine to process rx + tx and other for rx only.
Last msix vector will be used for separate tx interrupt.
o This is supported from fw version 4.4.2.
o Bump version 5.0.5
Signed-off-by: Sony Chacko <schacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Remove extra printing of mac address
o This driver also supports NIC only Qlogic adapters.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was not detecting the presence of NIC partitioning capability of the
firmware properly. Now, it checks the eswitch set bit in the FW capabilities
register and accordingly sets the driver mode as NPAR capable or not.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following changes have been added to enable the adapter to work in
NIC partitioning mode where multiple PCI functions of an adapter port can
be configured to work as NIC functions. The first function that is enumerated on
the PCI bus assumes the role of management function which, besides being able
to do all the NIC functionality, can configure other NIC partitions. Other NIC
functions can be configured as privileged or non privileged functions.
Privileged function can not configure other NIC functions but can do all the
NIC functionality including any firmware initialization, chip reset etc. Non
privileged functions can do only basic IO. For chip reset etc, it depends on the
privilege or management function.
1. Added code to determine PCI function number independent of kernel API.
2. Added Driver - FW version 2.0 support.
3. Changed producer and consumer register offset calculation.
4. Added management and privileged operation modes for npar functions. A module
parameter has been added to control it.
5. Added support for configuring the eswitch in the adapter.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes memory leak in error path when memory allocation
for adapter data structures fails.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupt test (offline) added in ethtool self test.
Register a temporary interrupt handler and then send command to fw
to raise an interrupt.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 1G/10G Ethernet Driver for Qlgic QLE8240 and QLE8242 CNA devices.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anirban Chakraborty