This patch defines the common operations to support multiple chips. It
includes common header file modifications to support the current chips
(T4 and T5). It also includes the following bug fixes:
- reconfirms the rnode state after an implicit logo.
- corrects the stats array size.
- sets up and checks flags correctly when coming up as master and finding
the card initialized
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Arvind Bhushan <arvindb@chelsio.com>
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a new file for T5 adapter operations.
Signed-off-by: Arvind Bhushan <arvindb@chelsio.com>
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch separates T4 adapter operations into a new file.
Signed-off-by: Arvind Bhushan <arvindb@chelsio.com>
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T5 adapter does not support onchip queue memory. Present logic fails to
allocate QP for T5 and returns an error. Also, if module parameter ocqp_support
is zero then we are unable to allocate QP which should not be the case. Ideally
if ocqp_support parameter is 0 or onchip queue support is disable then host QP
should be allocated before returning an error.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always bump the tcam_full stat. Also, bump wr reply timeout to 30 seconds.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It enables direct DMA by HW to memory region PBL arrays and fast register PBL
arrays from host memory, vs the T4 way of passing these arrays in the WR itself.
The result is lower latency for memory registration, and larger PBL array
support for fast register operations.
This patch also updates ULP_TX_MEM_WRITE command fields for T5. Ordering bit of
ULP_TX_MEM_WRITE is at bit position 22 in T5 and at 23 in T4.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both DB Flow-Control and DB Coalescing are disabled by default on T5
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for Chelsio T5 adapter.
Enables T5's Write Combining feature.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All T5 adapters will only support VFs on PF0-3 despite the ability of the
hardware to support them on PF4-7. This keeps our T4 and T5 adapters more
similar which simplifies host driver software.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements a low latency Write Combining (aka Write Coalescing) work
request path. PCIE maps User Space Doorbell BAR2 region writes to the new
interface to SGE. SGE pulls a new message from PCIE new interface and if its a
coalesced write work request then pushes it for processing. This patch copies
coalesced work request to memory mapped BAR2 space.
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable dev is initialized but never used
otherwise, so remove the unused variable.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QLogic applications use these callbacks to perform
o NIC Partitioning (NPAR) configuration and management
o Diagnostic tests
o Flash access and updates
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N says:
====================
This patch serires implements the following features in CPSW driver
* get/set phy link settings
* interrupt pacing
* get phy id via ioctl cmd SIOCGMIIPHY
Changes from initial version
* Made active-slave common for cpts, ethtool and SIOCGMIIPHY ioctl
* Cleaned CPSW DT binding documentation by seperating slave nodes
under sub-section
* implemented get phy id via ioctl cmd SIOCGMIIPHY
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement get phy_id via ioctl SIOCGMIIPHY. In switch mode active phy_id
is returned and in dual EMAC mode slave's specific phy_id is returned.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements support for interrupt pacing block of CPSW via ethtool
Inetrrupt pacing block is common of both the ethernet interface in
dual emac mode
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements get/set of the phy settings via ethtool apis
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change cpts_active_slave to active_slave so that the same DT property
can be used to ethtool and SIOCGMIIPHY.
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all the slave note properties to separate section to reduce the
confusion between slave note properties and cpsw node properties
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement to collect ethernet statistical information on ks8851_mll device.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove cast for kmalloc/kzalloc return value.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
remove cast for kmalloc return value.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been tested on a qnap TS-119P II. Note that enabling WOL with
"ethtool -s eth0 wol g" is not enough; you also need to tell the PIC
microcontroller inside the qnap that WOL should be enabled by sending
0xF2 with qcontrol(1) and you have to disable EUP ("Energy-using
Products", a European power-saving thing) by sending 0xF4.
Signed-off-by: Michael Stapelberg <michael@stapelberg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows ethernet drivers (such as the mv643xx_eth) to support
Wake on LAN on platforms where PHY registers have to be configured
for Wake on LAN (e.g. the Marvell Kirkwood based qnap TS-119P II).
Signed-off-by: Michael Stapelberg <michael@stapelberg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the second of the TLP patch series; it augments the basic TLP
algorithm with a loss detection scheme.
This patch implements a mechanism for loss detection when a Tail
loss probe retransmission plugs a hole thereby masking packet loss
from the sender. The loss detection algorithm relies on counting
TLP dupacks as outlined in Sec. 3 of:
http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01
The basic idea is: Sender keeps track of TLP "episode" upon
retransmission of a TLP packet. An episode ends when the sender receives
an ACK above the SND.NXT (tracked by tlp_high_seq) at the time of the
episode. We want to make sure that before the episode ends the sender
receives a "TLP dupack", indicating that the TLP retransmission was
unnecessary, so there was no loss/hole that needed plugging. If the
sender gets no TLP dupack before the end of the episode, then it reduces
ssthresh and the congestion window, because the TLP packet arriving at
the receiver probably plugged a hole.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series implement the Tail loss probe (TLP) algorithm described
in http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01. The
first patch implements the basic algorithm.
TLP's goal is to reduce tail latency of short transactions. It achieves
this by converting retransmission timeouts (RTOs) occuring due
to tail losses (losses at end of transactions) into fast recovery.
TLP transmits one packet in two round-trips when a connection is in
Open state and isn't receiving any ACKs. The transmitted packet, aka
loss probe, can be either new or a retransmission. When there is tail
loss, the ACK from a loss probe triggers FACK/early-retransmit based
fast recovery, thus avoiding a costly RTO. In the absence of loss,
there is no change in the connection state.
PTO stands for probe timeout. It is a timer event indicating
that an ACK is overdue and triggers a loss probe packet. The PTO value
is set to max(2*SRTT, 10ms) and is adjusted to account for delayed
ACK timer when there is only one oustanding packet.
TLP Algorithm
On transmission of new data in Open state:
-> packets_out > 1: schedule PTO in max(2*SRTT, 10ms).
-> packets_out == 1: schedule PTO in max(2*RTT, 1.5*RTT + 200ms)
-> PTO = min(PTO, RTO)
Conditions for scheduling PTO:
-> Connection is in Open state.
-> Connection is either cwnd limited or no new data to send.
-> Number of probes per tail loss episode is limited to one.
-> Connection is SACK enabled.
When PTO fires:
new_segment_exists:
-> transmit new segment.
-> packets_out++. cwnd remains same.
no_new_packet:
-> retransmit the last segment.
Its ACK triggers FACK or early retransmit based recovery.
ACK path:
-> rearm RTO at start of ACK processing.
-> reschedule PTO if need be.
In addition, the patch includes a small variation to the Early Retransmit
(ER) algorithm, such that ER and TLP together can in principle recover any
N-degree of tail loss through fast recovery. TLP is controlled by the same
sysctl as ER, tcp_early_retrans sysctl.
tcp_early_retrans==0; disables TLP and ER.
==1; enables RFC5827 ER.
==2; delayed ER.
==3; TLP and delayed ER. [DEFAULT]
==4; TLP only.
The TLP patch series have been extensively tested on Google Web servers.
It is most effective for short Web trasactions, where it reduced RTOs by 15%
and improved HTTP response time (average by 6%, 99th percentile by 10%).
The transmitted probes account for <0.5% of the overall transmissions.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using devm_request_and_ioremap() can make the code cleaner and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI header is not needed, so get rid of it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using for_each_set_bit() to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using for_each_set_bit_from() to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using list_move() instead of list_del() + list_add().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent bnx2x devices which are used mainly for storage from using zero
MAC addresses as their primary MAC address.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure SFP+ tap values to optimize link signal according to NVRAM setup.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RJ45 SFP module detection. In case the user set 10G link speed, and the
module doesn't support it, then force the speed to 1G and notify the user.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Bhushan